Installation
Well, installed it on Saturday - a professional looking, wires-hidden install took less than an hour - quite impressed as i'm not a 'Pro'
The kit comes with everything needed to install it, so as long as you know which wire is which in your car audio harness, you should be ok.
I purchased a spare ISO harness (£10) and chopped into that sitting inside, rather than cramped into my car. It also means if i change cars it's easy to move the car kit without taking wires from the car. The instructions aren't really much cop... But there is a chart detailing which wire on the wiring loom should be connected to which on your car audio leads.
It uses your ignition switched ACC circuit to turn on and off the power to your device, so you won't discharge your car battery if you leave your XDA in the charger. If you don't have an ignition controlled ACC circuit or you don't want it controlled like that, just connect both the 12v and ignition sense leads to your BATT lead on your car audio (put a switch in the ignition sense lead on the car kit if you want to control it yourself.
The kit uses your drivers side car speaker (or which ever one you want). You simply split the pair of cables between your head unit and speakers and the control box sits 'between' them. An external speaker is available but not included (despite what expansys' site said for ages) They can sell you the speaker but they don't stock it.
The microphone has a fairly stiff wire so it's easy to pass it through the headlining in your car to hide it. It's not as 'discrete' a microphone as the "bump" ones that come with Nokia car kits - think Tie-Clip mic and you're on the right track. It more than makes up for it's looks in pick up and echo reduction though.
I hide the fairly chunky control box behind the glovebox in my VX Vectra. It's about 2 foot from there to the back of the head unit and there is cable on the loom to spare. There's about a yard of cable from box to cradle as well. Watch out - the box gets quite warm when powered up, so be careful where you place it.
The cradle itself comes with backing plate connected to the cradle by a ball and socket connector that doesn't budge when tightened. however the backing plate can only move through fairly small angles, so for certain cars you'll need right angle brackets or custom made mounting points to put it on.
Sound Quality
The Sound quality on this is excellent. . There's no echo, no hiss, and the tones are natural unlike the usual tinny or dead car kit speakers. There is a car kit speaker for it seperately if you don't want to use your existing car speakers.
The kit doesn't have any problems powering my aftermarket 70W front speakers either - full volume is TOO loud (no distortion though).
The microphone is excellent. there's no need for the usual 'shouting' down the mic so the caller can hear you. On the motorway at '70' mph (!) i can talk softly and the caller hears me perfectly.
No echo or feedback and there wasn't any Dut-Dutde-Dut-Dutde-Dut pickup either (you know what I mean - the interference the phone signal makes)
GPS
The system provides a female PS2 port for GPS connection & external powering. Be warned! The PS2 port is the 'wrong way round' for Rikaline, Holux, Fortuna etc PS2 GPS mice. Expansys list the adaptor cable (female to female PS2 lead) as one of the accessories for the device, but don't regularly stock it.
I bought a Fortuna U2 PS2 GPS mouse - cheapest one they stock - and it's excellent. TomTom 5 accepts it as a TomTom branded wired GPS and cold start to readings on 7 Satellites was about 35 seconds. Perhaps it comes preloaded with some Epheremis data? I dunno. If i drive from home to work (50 miles) with everything switched off and then plug it in, tom tom takes maybe 5 seconds to notice the change. So far it seems spot on. MPH is out by 2 MPH compared to my speedo, but think that's my speedo
Audio Out & Telemute
The car kit has a telemute cord that you attach to the telemute wire on your head unit or car loom. In my case the head unit mutes the sound to the speakers completely and the car kit 'takes over' the front speaker.
As far as I can see the car kit notices the sound coming out of the XDA and mutes the radio then - theres no telemute signal coming from the XDA. The mute lasts for about 10 seconds AFTER the sound has finished. So when you first press TALK on the phone, the car kit mutes, but if the call hasn't connected and given you a ringing tone 10 seconds later, the kit 'demutes' the stereo. As soon as the car kit starts playing the ringing tone the stereo mutes again. A bit annoying when connection takes a while. The ten second pause in my stereo just because i've recieved a text message gets irritating, but not too much.
The downside for me is that the device plays everything the XDA2s outputs. TomTom, phone, WMA, notifications, the lot, and therefore mutes the stereo while this is going on, so i can't use the headphone socket to play MP3 into the Aux In on my stereo. I'm sure, however that i can figure out some way to 'switch' the wires into a WMA mode where telemute and speaker leads are disconnected. I'd have to switch it back for calls though...
Summary
Excellent car kit , let down slightly by the telemute and audio out function, but fantastic sound quality and nice connections. 8/10. Considering the opposition, there's no contest.
Fortuna U2 GPS seems an excellent receiver, made all the better by the £50 price tag...
Pics later in the week
Links (on Expansys)
Car Kit: http://www.expansys.com/product.asp?code=122685
Extra Speaker: http://www.expansys.com/product.asp?code=124130
Fortuna U2 GPS: http://www.expansys.com/product.asp?code=108897
PS2 Adapter cable: http://www.expansys.com/product.asp?code=122674
Related
I'm sick of trying to find a car cradle that has audio out, ps2 and 12v for charging!
Why is it that no manufacturers of xda cradles ever realise that some of us want to listen to mp3's in the car and have tom-tom voice prompts coming through our stereos!
Being right handed, I want my PDA on the right of the steering wheel, so I can operate Tom-Tom before setting off, or change tracks on media player. I did look at the Brodit pro-clip solutions, but they all seem to be for the centre console for my car (a citroen AX)
I've discovered that the driver's side vent mount has a removable panel, which means I can easily mount a small piece of wood (effectively a small flat shelf) for mounting a cradle, this also brings the device out of the reflective glare zone in the windscreen during night driving. It also means all I need is a standard xda iis cradle to do this mod.
So with much careful thought I've decided to do the following:
Buy a spare cradle:
http://www.my-xda.com/xda2s_other.html
Which leads me to the next question....
Has anyone got any modding experience with the xda2/xdaiis cradle?
similar to this old posting for the Wallaby...
http://forum.xda-developers.com/viewtopic.php?t=256&highlight=cradle
(although I couldnt see any of the images on this old posting!)
In theory, this project has 3 key issues to resolve...
1) Powering the cradle and Bluetooth GPS
Three options seem to be available...
a) The hobbyist approach...I've seen various "car-kit diagrams" like this one,
http://forum.xda-developers.com/files/xda_car_kit_circuit.jpg
but to be honest I have no pcb making experience.
b) 12V to 5dc cigarette socket transformer adapter to provide power to the cradle, and perhaps to the bluetooth gps for charging. This should be easier to achieve!
Anyone have any links for low cost solutions for this, obviously it would need to convert 12VDC to 5DC at 2-3Amps
c) As the xdaiis usb cradle charges directly from a USB power source, this seems an Ideal solution!
http://www.expansys.com/product.asp?code=EXP_USB-CLA
2) Audio out: THE MAIN PROBLEM!
Ideally I just want to get in the car and cradle the device, no other connections being required.
Therefore I need to modify the xdaiis cradle for audio output...
Ideally, the feed for the audio should come from the bottom connector, when the xdaiis is cradled.
With this in mind, I found this article about dismantling an xdaii cradle...
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=42&PN=1
If you look at the images on this web-page, you can see that - at the back of the cradle on the opposite side of the usb cable from the 5volt dc input is what looks like a pcb pinout for a headphone connector...
is this right? Can anyone confirm this.
Would it be possible to solder a connector onto here (assuming the solder pads connect to the 22pin connector!)
As this would be far easier than mucking about trying to solder onto the miniscule pins on the bottom of the 22pin connector on the cradle as it goes into the pcb!
If it works of course!
b) modify a headset
I did consider modifying an old wallaby headset to wire it into my car amp
http://wiki.xda-developers.com/wiki/Connectors , does anyone have any info on the pinout for the himalaya/blue angel headphone socket? I have also tried a friend's xda II headset on the IIs and yet again they have changed the pinout! The audio connections are once again totally different, resulting in the "echoing" effect when one headset is plugged in from the other device. This means that the audio ground pin has changed since the xdaII headphone socket schematic! This difference is also confirmed by looking at the handsfree "pod" on both headsets... The IIs has one button for answering a call, where the II has two buttons, wether it is the same as the XDA1 (Wallaby) remains to be seen....
c) buy a PDA2k 3.5mm headphone adapter...
http://www.expansys.com/product.asp?code=118289&sbadd=118289
Then use a standard lead to connect it to the hi-fi amp in the car.
3) charging the TOM TOM BLUETOOTH GPS
I'm wary of putting anything other than the recommended voltage (5VDC) into this device, so the best option is to supply power using (1b) or (1c) above, perhaps cutting into the supplied RJ cable to minijack psu to hook it up from the same supply.
While I'm on the subject of the bluetooth gps.... Does anyone knopw how long does the tom tom bluetooth gps work with a full charge?
Does it vary based on an active connection, or is it the same as on standby?
Do I need to power it in the car at all? Can I not just charge it as required at home? There doesnt seem to be much literature about the Bluetooth GPS reciever's battery life in the box!
Anyone care to comment on these ideas?
:lol: :lol:
I think the fact that no-one makes a cradle which provides audio-out through the bottom connector of the XDA2 is because the XDA2 doesn't provide this possibility. It's not the car-kit manufacturers' fault. Blame HTC.
However, I could be wrong... :roll:
My solution: I bought one of these XDA2 mounts ( http://www.pdamods.com/proddetail.asp?prod=A11XDA2MNT&cat=23 ) which works really well. It charges the phone and my TomTom BT GPS. To achieve audio-out I plan (eventually) to use the XDA2's headphone socket by drilling a hole through the mount's base in the right spot and using a 2.5mm jack adapted to play through the car stereo. Not an ideal solution, but surely must be simpler for you than trying to build a reliable (and safe!) 12V -> 5V convertor and butchering a spare XDA2 desktop cradle?
Just a suggestion... 8) Let us know how you get on. Good luck!
QUOTE 12V to 5dc cigarette socket transformer adapter to provide power to the cradle, and perhaps to the bluetooth gps for charging. This should be easier to achieve!
Anyone have any links for low cost solutions for this, obviously it would need to convert 12VDC to 5DC at 2-3Amps
Just about any mobile phone car charger will do.
Silicon s, you must be wrong :lol:
I have found someone that makes a DSP handsfree set with Audio on your car speakers, separate mic and all with the bottom connector. It even delivers laptopconnection for Dialup and GPS.
The overview
http://www.thb.de/showpage.php?lang=en&mode=show_product&cat=1&pid=2
Car Talk DSP
http://www.thb.de/showpage.php?lang=en&mode=show_product&cat=1&pid=2
The Cradles
http://www.thb.de/showpage.php?lang=en&mode=show_product&cat=1&pid=2
XDA docked
http://www.thb.de/bilder/take_talk/mda2_gps_big.jpg
http://www.thb.de/bilder/take_talk/mdaIII_large.jpg
MDA III - Important Information:
Replace file "Wavedev.dll" on your MDA III and restart the system. Audio response now can be listen via loudspeaker.
http://www.thb-service.de/download/MDAIII/Wavedev.dll
FYI, It appears that the replacement WaveDev.dll file offered by the car Kit company causes bluetooth headsets to stop working at all (not just in the car).
tfletch said:
FYI, It appears that the replacement WaveDev.dll file offered by the car Kit company causes bluetooth headsets to stop working at all (not just in the car).
Click to expand...
Click to collapse
That's what I'm looking for. Have you found anywhere to actually buy them? I looked over the whole site.
How about this alternative cradle. I bought one for my XDAIIs and it works perfectly. Got one for the birds XDA2 and that work great too.
It provides power to either a wired GPS or charges a bluetooth GPS, it has a built in speaker and a cables provided to run from the XDA's headphone socket to the cradle. THIS THING IS LOUD!
One word of caution, the speakers in my car are shielded so I don't get that warning noise from them that I am about to get a call or text. The speaker on the cradle is NOT shielded and so you do get interference when you are about to get a call or switch cells.
http://www.pdamods.com/proddetail.asp?prod=A1SSSPKMNT&cat=23
i thought about using my 6601 as an MP3 player in my car as well. but since my eclipse cdplayer does mp3, i abandoned the idea
option 1: cut up a 2.5mm headset and plug it into the top of the device
pros: cheap and effective
cons: have to plug it in every time (and unplug it to take a call)
option 2: pair a bluetooth headset with the device, crack it open and wire the speaker to a preamp
pros: wireless
cons: ruin an otherwise good bt headset, music would be in mono
option 3:
http://motorola.digitalriver.com/se...e&SiteID=motostor&productID=36065700&Env=BASE
"transfer audio to hands-free"
pros: wireless
cons: EXPENSIVE, pretty vague description
option 4:
http://www.itechdynamic.com/html/border22.htm
http://xprnnews.xfn.info/itech/nightingaleBSH338/en.htm
pros: wireless, stereo, routes incoming cails through car
cons: i cant find it anywhere
its called the "nightingale BSH338" or the "Bluetooth Stereo Clip Headset"
if anyone finds one, please reply with a link
ok i did some more reading on the subject and i found this (page 2 of the forum)
http://www.seidioonline.com/ProductDetails.asp?ProductCode=CK8AG21MXDA3
http://forum.xda-developers.com/viewtopic.php?t=17149
After thb introduced their first 'real' blueangel carkit, could this be the second ? I prefer this one because you don't have to connect a wire, but have a real cradle. The gps is also a plus.
http://www.expansys.com/product.asp?code=122685
Ciaos,
Kristof
I have it installed now and it worx good. Only problem is that it keeps muted VERY long (about 10 - 12 secs) when the BA produces a sound. Have to find somthing to fix this. I know this is a problem of the carkit because when the mute wire is grounded it switches directly on & off.
Just purchased this, and it looks pretty good, but the instructions are a bit naff.
Do i gather that the car kit's control box in effect gets placed in circuit "between" the car's head unit and the Front Right (or left) speaker. The cables are labelled radio FR + and - and FR speaker + and -. Do I just cut the iso cables for the front right speaker and connect the two ends to the ends of the car kit cables? I'm fine with car audio so this shouldn't be a problem
Does the car kit mute the radio for *every* noise or just phone, tom-tom etc? I guess I could just stick a switch in the middle of the mute circuit if i wanted to stop this (like WMA playing through aux in on head unit)
Hoping to have a play tonight...
It depends on the car you have. I have an Opel Omega with Bose Sound System fully integrated. At the passenger side under the glove compartemant was a plug that had al connections. The BSS has a phone audio input that outputs the pda sound to all speakers including Tomtom, and yes, all system sounds come over the speakers too. If this bothers you you could turn the sounds off in the Sound & Notifications menu. Check your car, maybe it has such a same plug (for factory fitted Carkits). First i wired it directly to the radio but it produced a horrible sound when the phone was cradled. It sounded like if 10 cats where fighting on the backseat. But that is over now. Could you let me know how long it takes for the mute signal to UNmute it after a sound is played. It takes about 12 secs here and that is WAY to long for every damn sound.
GaMeR64
Oh ok. I have a vauxhall vectra with the same mobile pre-wiring so I wonder if that might work for me as well.
Did the car kit cables just clicp straight in or did you 'butcher' them?
I'll let you know about the delay to turn mute back off again once i've fitted it (probably at the weekend )
What i did not to kill the originall plug is that i soldered off a connector from a broken VGA card. It should be the same one as that where you plug in your IDE HDD at the back off the HDD (male plug strip). I soldered all the carkit wires to that. It almost looks factory fitted. Pay special attention when connecting the audio wires to your plug. At first i fixed tham at the back of my radio but that made a sound of 10 fighting horny cats on the backseat. Be sure to connect it to the plug because there is some filter between it. At least that`s with my carstereo (Philips CCR800 /w Bose Sound System.
If anyone could help me with modifying teh Tomtom 5 sounds the help will be appreciated. I unpacked all the voice files but i can`t seem to find the RIGHT editor to open these .ogg files. I tried SoundForge and Audicity but no luck. They can`t open them.
Hi everyone, I am looking for Ideas on how to build speakers and a microphone into a full faced motorcycle helmet that communicates with my Wing (in stereo) via Bluetooth. I know there are commercial solutions but for the most part they are crap and a good setups (chatterbox) will cost in excess of $400. So I figure with the right guidance I could make a good system for a fraction of that $400.
What I’m thinking: (of course cheap is the slogan of the day)
1. Bluetooth adapter that will pair with my Wing and receive a stereo signal.
2. Noise canceling microphone
3. Decent (yet thin) speakers
The real question:
Would it be possible to strip apart a Bluetooth adapter and solder in speakers and mic. Allowing me to listen to music on my Wing while riding my bike. I would also like to be able to verbally answer and dial the wing with this setup. One of the big stumbling block is how to power the speakers (would an BT adapter have enough juice?), easily recharge (or replace batteries) in the adapter, and make pairing painless.
I would appreciate any ideas and comments you have. Thanks
Hello and Welcome to the forum!
But if you want to make some speakers in your helmet, Contact the police first and ask if it's legal.
I know a mate who has done that before and when he got a speeding ticket, the officers saw there were speakers.
He got a ticket for that aswell because it may inflect the safety and durability of the helmet.. LOL
Anyway, If i were you i just bought the original HTC headset wich is wired, and plug them in my ears.
Put on your helmet and you can call and such.
But maybe other people will have some other thoughts.
You think the mic will work in that enviroment?
ermm, well if you have a noise canceling mic than it should be no problem.
But i did some research for you and there are helmets availible with a bluetooth headset built-in. Connect your phone with that headset and play some music.
I've been looking to do the same thing. Its REALLY hard to get my helmet on with a bluetooth headset in my ear, its hurts as a matter of fact. I have to take some of the padding out from the helmet if I dont want pain, but thats just not worth the safety risk; I bought a $500 helmet for a reason. Lol.
The mic wouldnt even have to be noise canceling IF you kept the mic behind the chin wind gaurd or inside the helmet somehow.
I totally understand, I paid $700 for an Arai helmet for a reason and its not because of the *****en graphics. What I have started to do…
I have a set of Skull Candy headphones that I removed the speakers from that will fit nicely into my helmet and have great sound. I did a test and spliced the speakers in to the USB headphone adapter (stock) for my wing. I ran into my first problem…. The wing doesn’t have enough poop to drive the speakers. So I will need to use some kind of speaker amp. I found a cheap ($8 + shipping) and small amp on Ebay ( http://cgi.ebay.com/ws/eBayISAPI.dl...STRK:MEWA:IT&viewitem=&item=260255057258&rd=1 )
So I’m thinking that if I can find a cheap Bluetooth (stereo and voice command capable) I could crack it open cut out the original speaker wires and solder in wires to connect to the head set amp. The head set amp looks small enough that I should be able to hide it someplace in the padding of my helmet. Then solder in wires to run from the amp to the speakers and finally mount the Bluetooth on the face guard infront of were my mouth would be.
What I am stumbling with is power. I need to figure out how to make the Bluetooth easy to charge and how to power the amp (requires 1 AAA battery). I would need to make the amp easily accessible to change out the battery which seems like a pain in the ass and may look ugly. What I would really like to do is have a common power source for both device so when I am home I just plug in one cord to the helmet. But I don’t know if that is even possible.
I really want to make this work but in the end this all needs to be functional and CLEAN. I don’t want it to look like I Forest Gumped my way though this project.
You might look at a tactical throat mic and a in-helmet speaker setup from midland. You could also try a in ear tube type setup from Midland also. Both products are for their GMRS radios, but I think with some modification you coud get it to talk to a bluetooth device.
Also you might look at Fire/police communication sights as some departments use bluetooth adapters with their 2 way radios for hands-free mic's that don't have to be connected to the radios.
Let me know if you ever come up with anything, this sounds like a very interesting project....
BG
I found this Bluetooth car unit last weekend and would like to share with you all.
In my own experience, this is the best one I ever tried.
LiquidAUX™ Bluetooth® Car Kit
http://us.kensington.com/html/14484.html
I got it for total $75 in Comp USA. This unit plugs directly to car cigaratte power plug, and the 3.5 mm audio jack plugs to your car AUX port. Yes, its designed for car stereo that has an audio AUX plug. I know there are some products that also integrate FM transmitter for feeding the audio to the car stereo, and I have tried those, but this one is much better if your car has an AUX input and you simply need to add a bluetooth connection to your phone.
The microphone is very good, even though my power plug in deep buried, and I was thinking to extend the plug with an extension cord, but indeed it still works well.
It auto connect to my HD when I turn on the car, and it transmits both phone and music (A2DP) with a very good sound quality.
It comes with a remote control that you can tied to your steering wheel to make it even better. Our HD does not have a DPAD and controlling music playing has been a challenge in the car. With this remote, all those issue no longer there.
I used to use a direct cable connection to connect my HD to my car stereo, and sometimes when I simply forget or feel lazy and just want to go right away, I will not be able to accept call or play music from my HD. With this BT connection, when I walk in to my car and switch it on, it auto connects to the HD, and the remote works right away to start playing music or make a phone call.
The previous BT dongle I used to have, such as the itech BT dongle, or the Jabra BT dongle, I always have issue to swith them on, swith them off, and sometimes it does not connect, and then have to remember to charge them once in a while.
With this unit, I don't have all of those issues, and it simply merges together nicely with my car stereo as if it has BT integrated.
I highly recommend it, if you have a AUX port in your car stereo. If you have a casette player, it should work also, but you would like to use a coupler to connect the both 3.5 mm audio jack together.
I got one of these from for about £40 from Amazon, but I had the problem of the cig lighter always being on show, which was annoying.
I go this handsfree kit, http://www.parrot.com/uk/products/hands-free-car-kits, which is by far the best I have ever used. Has full iPod support, 3.5mm jack and usb support.
Full colour screen and phonebook storage / voice dial.
nicelad_uk said:
I got one of these from for about £40 from Amazon, but I had the problem of the cig lighter always being on show, which was annoying.
I go this handsfree kit, http://www.parrot.com/uk/products/hands-free-car-kits, which is by far the best I have ever used. Has full iPod support, 3.5mm jack and usb support.
Full colour screen and phonebook storage / voice dial.
Click to expand...
Click to collapse
a parrot that works well with a smartphone?! really...? I'd heard nothing but bad about probs with the old touch dual i had - has this been fixed since & works with the HD then? if so i'm in...
Lord of the Badgers said:
a parrot that works well with a smartphone?! really...? I'd heard nothing but bad about probs with the old touch dual i had - has this been fixed since & works with the HD then? if so i'm in...
Click to expand...
Click to collapse
Yep, parrot really works fine both with my HTC Touch Cruise(P3650) as the HTC Touch HD
I use the xcarlink USB/SD adaptor with bluetooth module. It plugs directly into the CD changer port of the stereo, allows me to charge my phone via the USB port whilst streaming audio through the bluetooth connection. Audio auto-pauses when I receive calls, which also use the stereo speaker system and music functionality is controlled via the normal stereo controls or the cars steering wheel controls. Track time, etc., is displayed on the normal car stereo display.
There are a few functionality niggles, but they are easily overcome with a dash mount for the phone and a skin for mobile media player that has large buttons. I designed a skin, just for use in the car, so everything is really easy now.
http://www.shop2us.com/car_mount/d2_fm_kit.jpg
Hi All,
I have just purchased and tested this product. It cost just £22 from Ebay. Quite a bargain really. The build quality is quite poor. However, the D2 does fit quite nicely and you don't need to fiddle with it too much to get the mini USB connected. One strange thing is the side flanges. They do overlap the green and red phone buttons slightly, so you could find yourself accidentally calling someone when inserting the D2 into the cradle.
Once in, it is an excellent product. The sound quality through the car radio is superb. Even driving through London (where the airways are filled with legal and illegal radio stations) there is no interference with this transmitter. I have tried a few of these type of FM transmitters and can happily say this is easily the best so far. The volume on the D2 needs to be turned down to about 13 or 20% on the HTC, otherwise you will get some distortion when playing loud music.
Re-tuning is a breeze with the back-lit LCD screen, if the frequency you have it on has some interference.
One problem is making or receiving a call. When a call comes in, you can hear the ringing through the car speakers. However, this device disables the D2 microphone and does not have one built in itself. The only work around for this is to have a bluetooth headset. Therefore, once a call comes in, the bluetooth headset will then provide the sound and microphone and so you can speak/hear as normal. The car speakers will be disabled once you accept the call through the bluetooth headset. Obviously the headset will need to be connected first. Personally, I use a small programme called bluepower. This turns on bluetooth on my D2 when it is being charged and then turns it off (to save battery) when it is not being charged. Therefore, as soon as I put the D2 into the cradle, it links with my already paired bluetooth headset
So, I can now sit in my car with my D2 charging, playing music through my car radio and make/receive calls using my bluetooth headset without any problems....
All sounds great doesn't it?
However, there is one small problem.
If I choose to listen to a different radio station, I will not be able to hear my D2 ring or hear when an email/text comes in, or to the voice guidance on my iGO8 (not that I use it).... You may consider this a safety feature because you don't want to have this distraction whilst driving do you? Obviously you can still see these events in the usual way, if your screen is turned on. This is not such a huge problem I don't think, but some might.
Perhaps it will be easy to be able to somehow link up a working microphone with this system and have a rather decent hands free system, but I don't know how to. I have seen other threads which have also described this problem with other such systems, but never a solution except the bluetooth headset one. Maybe someone can suggest a registry tweak for this or a Mortscript programme???
Anyway, to conclude, I am very happy with this purchase, especially at the price.
Hope this helps someone
will the Pure fit in a TD2 cradle?
Will the Pure fit in a TD2 cradle? The bottom ends appear to be differently shaped. Is it close enough that the two can be interchanged for a cradle like mitsi posted?
I want a nice cradle with a built in usb plug so I dont have to figit. The proclip one is too darn expensive. Whereas the custom fitted car cradles for the TD2 are plentiful...
Mic For the FM Transmitter ALMOST !!!
Well like you i bought one of these fine products I did come across a couple of issues (and work arounds).
1. At certain output frequency's the GPS did not work ??, noticed that when the power to the FM Tx was removed the GPS signal returned. as I tried different channels the interference varied so worth looking out for.
2. Again at different output channels I would pickup the mobile trying to make a connection to the network (approx every 10min), again changed the channel the effect varied from bad to zero.
Microphone, I took my unit apart and the pcb has the position for a MIC marked on the pcb but no mic fitted. I took out a mic from the supplied handsfree kit supplied with the phone this fitted and off I went to try but no luck.
On further investigation the mic needed to be wired pack to the usb plug BUT the pins for the plug are enclosed in the glue used to hold the plug in position and there were no leads off the plug to wire too !!!!!!!!!!!!
But like u the unit is still worth the cash