Related
Guys, I'm frustrated now. I've refreshed the ROM of my G4 version of Dopod 818pro (2.15.0001 or something I just can't remember). Unfortunately it fails and I cannot even turn the power on. My WinCE colleague told me that the Boot Loader was damaged. I am now seeking for some place to re-program the chip and hope if someone can provide me boot loader program. I really appreciate your guys help!!!
Are your Bootloader Realy damage? You mean you cant enter it? Or you havent Power to start your Device?
SD Flashing doesnt work without Bootloader!!
JTAG Flashing (hardware nearest Flashing!!) isnt developed for G4 Plattform. (i think so ... look in the Wizard board ... they talk about JTAG flashing and Wizard G4 must simulare like Prophet G4!!)
the bootloader really damaged, I cannot enter the three stripe screen by holding CAM, PWR button and hit reset hole. Do you mean that I even cannot use JTag to burn the chip???
I do have two fully charged batteries. But it should not be a problem of battery, I tried to connect it to charger but it gives no response, no LED
Using JTAG to revive a wizard is either a myth, or an undiscovered secret. If you cant get into bootloader, your chances of reviving your device are slim.
JTAG isnt a secret ... its more like ... hardware knowlage. If you know what IC is your ROM. You can found over the IC Spec the right Pins for JTAG Programming. If i can get a G4 S200, i can try my best.
yes, I know that using Jtag to rewrite boot loader is complex, but it seems like it's my last chance. NetrunnerAT I really appreciate your help but I'm in Shanghai, China so I have to find someone locally who can help me with that. Wish me good luck and I'll keep you guys updated about the result
If I can find someone who can help Jtag my phone, where can I find the correct bootloader program for my cell? is it downloadable?
guys, I finally found a place to revive my prophet. However, they don't know how to jtag it either, neither do they have a programer to rewrite the chip because they say the programer is very very very expensive. They just changed the old chip with one which has correct ROM and now my G4 Prophet turns to a G3 one...anyway, I can use it now.
Thx!
You have change your rom and it is now G3!!
Can you say me what IC they have exchange! If i know it ... and get a damage device, its possible to found a solution for all Prophet users!
No problem, I kept the damaged IC at home, I'll check the model No. and will let you know
er... One more question, I want to dump the current ROM to my SD card, however the wiki doc says it needs to unlock G3 first. But another doc also says unlocking G3 will downgrade my OS to 1.0.13.21. It's like a kind of deadlock, can I just unlock G3 without changing OS?
uhm ... i think you must downgrade your OS first to CID unlock ... after that you can upgrade to your rom and make SD-Dump!
ok, then that is to say i'll never be able to get a backup of the ROM I currently have.
I'll wait for some weeks and will try to "torture" my prophet again. It was just fixed and I'm supposed to "rest" it for some days, but sooner or later it'll be unlocked, hey heyhey....
Hi, I'm back, the chip is a "M-System MD8832-d16-v3-xp" with a clearly name "Disk On Chip" on it, hope this can help you locate the chip
http://www.m-systems.com/NR/rdonlyr.../0/EOL_DOC_G3_P3.pdf|EOL_DiskOnChip_G3_P3.pdf
Cool ... i read some PDFs ... this is are very nice entry in the PDF!
Compatibility Issues
The recommended replacement, DiskOnChip G4 1Gb/2Gb 9x12mm FBGA, and H1 2Gb
12x18mm FBGA are ball to ball compatible with DiskOnChip G3/P3 7x10mm, 9x10mm FBGA
products that are being discontinued. It is necessary to upgrade software based on TrueFFS 6.2.x
to TrueFFS 6.3.2 and above when upgrading to DiskOnChip G4.
If the different betwen G3 and G4 is the TrueFFS Driver and the G4/H1 is Pin Conpatibel ... possible if i get a half damage device i try to solder a H1 DOC on the PBC and reformat it.
[edit]Holly ****! THX i have found the Migration Document with JTAG Pins!!!
http://www.m-systems.com/NR/rdonlyr...MigrationGuideDOC_G4_1Gb_to_H3_1Gb_Rev0.2.pdf
how are you going to access the pins on a FBGA?
yanuk said:
how are you going to access the pins on a FBGA?
Click to expand...
Click to collapse
you dont. you take a bricked one, de-solder it, and manually trace them to somewhere on the motherboard using a multimeter.
can any body help me with a jtag points for a g4 wizard doomed with a incorrect ipl
Give me a damage Wizard board and i say the JTAG Pins! G4 and G3 have the same JTAG Pins.
I search for a damage Prophet to but i doesnt want pay over 80€ for a community project without any payment. It some on give me a wizard or prophet Board ... i desolder the IC ... search for JTAG Pins ... and reflash it ... send it back but working :->
the device doesnt damage if i resolder the DOC ... i have the right soldering mashine.
NetrunnerAT
Where you saw on DOC points jtag ?
You need the signals TDO TCK TMS TRST TDI.
DOC only memory and there no these signal.
What jtag you will use? And no program for flash DOC through jtag - see about Universal jtag.
hello
im using my o2 XDA atom (black) for six months with no problem and regular rom upgrades till yesterday when i accidently used the ATOM EXECUTIVE boot loader eboot.nb0 file on my 2GB miniSD card and entered bootloader on (camera + reset) the ATOM.
Now i cannot use my ATOM bootloader atall.
when i enter it, just a black screen and no buttons work either until i remove battery and insert and power on.(while in the bootloader when connected to pc the orange led lights but no connectivity)
the phone works fine although bootloader is not possible with SD or via PC
Im still using the fone with no problems but seeking help to repair the bootloader.
Im willing to upgrade my rom to the latest rom upgrade available from Jiggs.
sidhrath said:
hello
im using my o2 XDA atom (black) for six months with no problem and regular rom upgrades till yesterday when i accidently used the ATOM EXECUTIVE boot loader eboot.nb0 file on my 2GB miniSD card and entered bootloader on (camera + reset) the ATOM.
Now i cannot use my ATOM bootloader atall.
when i enter it, just a black screen and no buttons work either until i remove battery and insert and power on.(while in the bootloader when connected to pc the orange led lights but no connectivity)
the phone works fine although bootloader is not possible with SD or via PC
Im still using the fone with no problems but seeking help to repair the bootloader.
Im willing to upgrade my rom to the latest rom upgrade available from Jiggs.
Click to expand...
Click to collapse
At 6 months time I believed your device is still covered under the warranty, why don't you refer back to your supplier.
powerwoot said:
At 6 months time I believed your device is still covered under the warranty, why don't you refer back to your supplier.
Click to expand...
Click to collapse
I doubt if service center will accept the unit since it was flashed "accidentally" with an ATOM EXEC boot loader.......
brian_2cool4u said:
I doubt if service center will accept the unit since it was flashed "accidentally" with an ATOM EXEC boot loader.......
Click to expand...
Click to collapse
why you don't try to reflash it back to WM6/WM5 for ATOM via DSUU mode (the bootloader will also overwrite during the update process)
note: just my thought, I don't have experience on this issue. just be aware the bootloader issue is the most dangerous part. one mistake will make your device become a paper weight.
yea but the sad part is that i dont have warranty
and the rom upgrade via pc is not able to continue
as once the fone goes to boot loader mode
its just dead like full black screen with no buttons working
sidhrath said:
yea but the sad part is that i dont have warranty
and the rom upgrade via pc is not able to continue
as once the fone goes to boot loader mode
its just dead like full black screen with no buttons working
Click to expand...
Click to collapse
bro, upgrade via DSUU not bootloader
hock up your usb, sync with activesync then run Device Software Update Utility.exe
to be safe copies the 6 files into your c:\windows\temp and run the exe from there
yeah, why don't you reflash as what chartreux suggest. Read wiki here on how-to http://wiki.xda-developers.com/index.php?pagename=ATOM_DSUU
Hi guys,
Hi,
I'm a hp rw6828 user and is very much enthusiast to try out those wm6 roms made by those experts. However, i did a mistake while trying to flash.
I tried flashing with a rom from wantat but i forgotten to delete the EBOOT.nb0 before i clicked "upgrade". Then the program stopped at 6% for a long time and didnt move. I disconnect the cables and tried to turn the device on.
THe device can go into the wm6 and the start button can be use but the screen is "moved" to the right side and other function is not working.
After that, i did a hard reset and the the os seem to work like normal. However, when i tried to go into bootloader mode by pressing both "_" and soft reset. That didnt work. I tried another way by taking out the batt, leave it for a 10mins, press both "_" and soft reset, put in batt, release soft reset then "_" keys. That didn't work either.
But, just lately, i've tried taking out batt, holding the camera key and softreset, place back batt, release soft reset n camera button. This method works and i get what it seems to be an atom bootloader?
i get a black background with "MN1 Bootloader Mar 29 2006 13;52;14 copyright..... 1) debug module through UART 2) jump to DM Enter your selection.
I've searched the forums and found few ways to downgrade back to wm5 but those aren't the same conditions with what im facing. Can someone recommend how can i downgrade back to wm5 with the conditions that im facing? All you help is much appreciated. THank you.
You are lucky , at lease your device now become atom. My was totally cannot on power and just vibrate. Till I have to sent it back to HP SC and change the main board . Can you understand chinese , if yes than I have a solution you may try . Else you have to wait . I just download a program and doing some testing , the program is in chinese language .
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
elus said:
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
Click to expand...
Click to collapse
I don't think you still can claim under warranty unless you can make your phone total can't on and access to windows mobile. Last time I sent it back they charge me RM 385 to change the main board . I did talk to their technical personal , it seen like they don't know what is bootloader and flash it back to original rom . What they do was just change the main board with preloaded program .
Good luck
If you think that you can claim you warranty , than you just go a head . If not , may be you can access my thread "HP6828 WM6" , download any one of the rom that I post , follow the instruction accept downgrade bootloader . Enter your phone in bootloader mode . If you can start the process , than it will flash a new hp bootloader into your phone .
Against . Good luck
Cheers
I'm from malaysia also.
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
elus said:
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
Click to expand...
Click to collapse
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
nhocbanme said:
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
Click to expand...
Click to collapse
Can share the information how to restore back the HP original bootloader ? And the procedure . Thanks
First you must have HP bootloader file (Eboot.nb0) 1.01 or 1.05 are OK.
- Use DRUU to restore Bootloader : replace ATOM bootloader file with HP bootloader file
- Use miniSD to restore Bootloader : copy Eboot.nb0 to miniSD card, go to bootloader ... wait 1' it will auto hard reset.
After flash successfull remmember remove Eboot.nb0 from miniSD.
- Reflashing Bootloader using JTAG. (Use only when can't use two above menthods)
HP Bootloader 1.01 : http://rapidshare.com/files/82853862/HP_BL1.0.1.rar
HP Bootloader 1.05 : http://rapidshare.com/files/82853924/HP_BL1.0.5.rar
nhocbanme could you please specify which specfic DRUU should be use for your method? Thank you.
You should use DRUU of Chartreux, replace Eboot.nb0 and choose OS and Eboot
Remember copy a HP68xx ROM (diskimage_Ver.nb0) to C:\Windows\Temp with DRUU of Chartreux then start...
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
elus said:
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
Click to expand...
Click to collapse
-You must extract RUU in C:\Windows\Temp (no sub folder) then replace Eboot.nb0 with Hp bootloader 1.01/1.05
-Copy a diskimage_Ver.nb0 (any ROM WM6 for HP 68xx) to C:\Windows\Temp
-Run the DRUU program and choose OS and Eboot and start.
Goodluck !!!
It worked! Thx a lot nhocbanme and wantat. The methods restore the atom bootloader to hp bootloader. The DSUU by chartreux is a good tool.
Now, i would like to put this solution up into the wiki. How may i do so? Thank you.
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
williamSun said:
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
Click to expand...
Click to collapse
OK, please read my topic, I'll post a WM5 ROM flash via miniSD
help !!
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
I dont think i can help u much here as im still new. From the looks of your problem, i guess u forgotten to cut the first 12bits (or something like that) of your bootloader when u use it to flash via mini sd. Maybe you can try the JTAG method mentioned in the atom wiki to restore your bootloader. Good luck.
Thanks guys!
The same exact thing happened to me yesterday..I was already about to sell my ipaq as a dead unit and i came upon this thread and after following the steps it did made ipaq alive again..
thank you very much guys,i hope you continue to help more people..
god bless and best of luck to you
more power xda-dev!
hello,all the masters of this site and pda phones....i have a spv m3000 from orange G4 locked and tried to flash t-mobile radio prodigy with softSPL...it went on first screen with the beer image and got stuck on it...after i removed my battery it wouldn't start,enter bootloader,soft,hard reset it wont even charge(red led not blinking) my computer doesn't recognize it.i tried giving the batey a 9v,6v shock and nothing happened phone is still dead...i'm not a good electronist so i can't use the method to rewrite the inernal memory soldering wires...etc....could you give me a solution???i'm desperate(
xardas_90 said:
hello,all the masters of this site and pda phones....i have a spv m3000 from orange G4 locked and tried to flash t-mobile radio prodigy with softSPL...it went on first screen with the beer image and got stuck on it...after i removed my battery it wouldn't start,enter bootloader,soft,hard reset it wont even charge(red led not blinking) my computer doesn't recognize it.i tried giving the batey a 9v,6v shock and nothing happened phone is still dead...i'm not a good electronist so i can't use the method to rewrite the inernal memory soldering wires...etc....could you give me a solution???i'm desperate(
Click to expand...
Click to collapse
Well, there's no such rom 't-mobile radio prodigy',you are mixing things here.Its either Radio Rom or OS(Rom). Assuming by your post 'the beer image' as you say,it must be the "Button's Rom 1.05" with IPL/SPL 1.05 (G3 Bootloaders). Did you flash the Button's Rom 1.05 on your G4 device,well,if so then,its a "BRICK",coz flashing a G3 Rom with IPL/SPL in it'll certainly brick a G4 phone,Now nothing can be done with it.
well i've heard something of leaving it 24 hours without the battery and shoking the battery but no luck so far...isn't there any program that would recognize this brick as a flash memory so i could just put the bootloader back?and yes i have put a g3 rom on my g4....and it makes me feel like an idiot...can't i just jump start the thing into the bootloader?(T-Mobile_UK_2.19.11_Radinly - this is what i flashed)
xardas_90 said:
well i've heard something of leaving it 24 hours without the battery and shoking the battery but no luck so far...isn't there any program that would recognize this brick as a flash memory so i could just put the bootloader back?and yes i have put a g3 rom on my g4....and it makes me feel like an idiot...can't i just jump start the thing into the bootloader?(T-Mobile_UK_2.19.11_Radinly - this is what i flashed)
Click to expand...
Click to collapse
Are you sure it was T-Mobile_UK_2.19.11_Radio only which you flashed and not the Button's Rom 1.05 ? coz flashing any Radio rom will not Brick any phone,regardless it being a G3 or G4,coz it doesn't include any IPL/SPL (Bootloaders) in it,its safe to flash to any G3 or G4 phone.
But what about you said it boots up to splash screen with a 'Beer Mug' on it,coz only Button's Rom splash screen displays a Beer Mug on it.
i'm certain this is what i flashed...and it was a beer mug(at least half of it) now it doesn't do anything...after i removed the battery it died
Could it be the battery?????
xardas_90 said:
i'm certain this is what i flashed...and it was a beer mug(at least half of it) now it doesn't do anything...after i removed the battery it died
Could it be the battery?????
Click to expand...
Click to collapse
Strange !!!
A Radio Rom never flashes any splash screen and it never displays any splash screen,especially a Beer Mug splash screen,you must have been mistaken and downloaded and flashed the Button's Rom 1,05,which has G3 IPL/SPL in it,and now its Bricked,nothing can be done with it to revive,except replacement of the 'DOC Chip' (M-System Flash Chip),which I'm afraid is not possible by anybody other then the manufacturer/vendor of the device.
just found out that in the directory named T-Mobile_UK_2.19.11_Radinly was CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE....did i brick it?...and how much would it cost to change that chip?...any place i could order another motherboard? maybe it's another way to do it...maybe someone does know how to use JTAG...give me some advice please...
xardas_90 said:
just found out that in the directory named T-Mobile_UK_2.19.11_Radinly was CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE....did i brick it?...and how much would it cost to change that chip?...any place i could order another motherboard? maybe it's another way to do it...maybe someone does know how to use JTAG...give me some advice please...
Click to expand...
Click to collapse
!
YUP !!! there it is,I was correct, its Button's Rom 1.05.
Well,yes ! its "BRICKED"
Only,manufacturer/vendor can provide you the motherboard or tell you the exact cost of it,or you can try the Ebay if they have it or can provide it.
Secondly,its still not known or if anyone can revive it through 'JTAG' ,guys here have been working on it,but were not successful and stopped trying it,you can have further info on it by checking out this link or 'Search' through google.
http://forum.xda-developers.com/showthread.php?t=274766
one more question and that's all...will the orange service or repair center notice that i've been "playing" with the device?maybe with a little luck they will replace it..or replace the motherboard :-S...thank you o much for helping
well....to all the readers of this post...i didn't manage to revive it through any method and decided to send it to the provider repair center...i have sent a message to caesar54 who managed to revive his wizard using jtag and waiting for a reply....IMPORTANT : DO NOT FLASH YOUR G4 DEVICE WITH A G3 ROM IT WILL BRICK YOUR PDA (I JUST FOUD OUT THE HARD WAY) SO REMEMBER..IF YOU DON'T KNOW WHAT YOU ARE DOING....DONT DO IT...i will post updates on what i have done with mine if someone intersted...
xardas_90 said:
well....to all the readers of this post...i didn't manage to revive it through any method and decided to send it to the provider repair center...i have sent a message to caesar54 who managed to revive his wizard using jtag and waiting for a reply....IMPORTANT : DO NOT FLASH YOUR G4 DEVICE WITH A G3 ROM IT WILL BRICK YOUR PDA (I JUST FOUD OUT THE HARD WAY) SO REMEMBER..IF YOU DON'T KNOW WHAT YOU ARE DOING....DONT DO IT...i will post updates on what i have done with mine if someone intersted...
Click to expand...
Click to collapse
Wish you a very goodluck there ! hope you get it working
thank you very much zabardast....i went to the orange shop where i was instructed by someone "high ranked" and someone over there told me that they have a tool that writes software even when the phone is dead...probably through a service cable or something...they said it would be back in 2 weeks maximum...and i will be informed of the price of the repair wich i will post (including my decision) anyway agan "DO NOT FLASH IF YOU DON'T KNOW WHAT YOU ARE DOING"...hope it will get it back after 1 week functionally and cheap...i will search other forums and find posible solutions that i will post...till' then...good luck and work safe
until my phone comes back repaired or not i'm searching for an alternative...does anyone have a wizarrd to sell?preferably a broken one...broken display or something...but with the mainboard intact?
hello xardas_90
i have a recently bricked wizard (xda mini s)
now we are working on finding the jtag test points on the main board to reflash the
bricked 1 , so i am glad if u join us in thread (( Dead WIZARD Never! Let's REVIVE ))
to share info.s and to reach our goal . please join us
well when the board comes back be sure i'll help...but there would be another soluution...we could find a site or store that sell DOC chips...the rest is simple...we just need that chip...i'll search other forums for wizard jatg points...i really like your initiative...
There Is Hope
1.Se poate scrie bootloader prin JTAG
2.Nu exista nici un DOC cip.
3.Nu va putem furniza informatii gratuite service pe mail incercati pe www.flashgsm.ro/forum
----- Original Message -----
From: Rebirth A.D.
To: office
Sent: Friday, May 02, 2008 9:17 PM
Subject: Re: reparatie
aveti cumva DOC cipul care contine bootloaderul?sau o placa de baza second hand?...sunt din ploiesti si nu pot veni in bucuresti momentan...nu se poate scrie bootloaderul prin JTAG?multumesc pentru reply si astept un raspuns
Translation : Original message : do you have the DOC chip that contains the bootloader?i'm from ploiesti and i can't come ti bucharest for the moment....can't we write the bootloader through JTAG? Thank you for the reply and i'm waiting for your answer...
Answer
1 - IT CAN BE WRITTEN THROUGH JTAG
2-no doc chip
3- use out forum because we can't tell you how to repair your phone free through e-mail
a fiend of mine wich works at a repair center said he could discover JTAG points but omly with a board that is functional...anyone out there willing to sacrifice or sell?i'll post news on JTAG
so it is a good news , that guy could help , keep trying with me.............
Where r u xardas_90 ??!
any news about ur device , jtag
nothing
nothing new....ssince i don't have a functional mainboard...nobody can tell me the jtag points....still waiting for my device to come back from the provider...i'm waiting for 2 weeks...
i upgrade p3400i with (HTC Gene - stock - 1.17.720 - ROM)
and now my Phone is Dead no red or green light
only when i press hard reset key with stylus the red and green key bilk at ones
plz help me
ankit360 said:
i upgrade p3400i with (HTC Gene - stock - 1.17.720 - ROM)
and now my Phone is Dead no red or green light
only when i press hard reset key with stylus the red and green key bilk at ones
plz help me
Click to expand...
Click to collapse
sorry to say its your mistake , you select the wrong Rom .
The 1.17.720 - ROM , its for p3400 not for p3400i
i dont have any solution for you,
maybe somebody can help you
thankx
sprite clone backup
i have taken backup of rom through sprite clone
can any body help me now
i was planning to run gene_hspl_HT8x.exe but it failed.
i am also wish to update rom but for that we need to remove spl hspl first as someone said that newer version are locked for rom update.
for more info on this talk you can see here
http://htc-android.com/viewtopic.php?f=5&t=64&sid=01547ccf0c90499d8f75f30018715da4
my phone is still running.
lots of people i think have 3400i now but this xda-developer forum has no info for this device.
i wish someone could start adding sub forum for this device so that newcomers like us get proper help to the things we do with our device.
regards
mak
india
?
hi atomicmak
i m from india also
can i send my phone to service centre ?
or go to shop and get it replace because it is only 2 day old
i've heared that sony people are doing servicing of htc and they are authorized service centers.
you can surely try to catch them and tell them you messed up with the phone and need recovery and i think they will be able to solve your issue with some money they charge.
hope this helps.
mital
Unbrick solution
Have you people really checked the following post?
http://forum.xda-developers.com/showthread.php?t=434349
ankit360 said:
hi atomicmak
i m from india also
can i send my phone to service centre ?
or go to shop and get it replace because it is only 2 day old
Click to expand...
Click to collapse
try pressing power key and camera button and press soft reset using stylus when you get into the boot loader try to flash with the stock ROM. Make sure that your SPL is changed to normal from orefklovs ... if the SPL is changed they will tell you that the warranty is void now. i got my board replaced after i flash with the stock ROM. which state are you living in? I think somebody has introduced an unbricker try that also..... my advice is dont do anything in excitement..... please study and research everything after that apply it in the phone....... gudluck.....
no man i try it but it not showing bootloader i think ipl is also damage
ankit360 said:
no man i try it but it not showing bootloader i think ipl is also damage
Click to expand...
Click to collapse
try again and again (press camera and power button together and soft reset with stylus) until you get into into the botloader screen... at once flash with original stock rom and make sure olipros SPL is changed to normal SPL.....it worked in my set... i dont know any details...
to http://www.dig-cn.com/forum-110-1.html
find the solution
to suchunjian
in that link i saw one spl mentioning that p3400i. is that really for the new gene. i dont know that language. if it is for the new gene then please inform all the gurus about it.
i upgrade p3400i with (GENE HARD SPL)
and now my Phone is Dead no red or green light
only when i press hard reset key with stylus the red and green key bilk at ones
plz help me
my gene dead :?(
i have same issue bcoz wrong flash i go to htc service crntre they repair it
if u don't have warranty use jtag method
P3400i is Dead HELP ME
y device Info
Serial No. - HTC8xxx
ONBL - 1.06.0000
SPL - 1.06.0000
The handset can only enter the safe mode, brushes any software to 2% to be defeated
thanks:
Closed as per OP Request.
Dave