1. problem started when trying to down grade cingular 8525 from Black Satin 2.10.Olipro for warranty return.
2. Used mrvanx downgrading guide to wm5.
3. Used the following Rom to downgrade:
New cing/ATT aku3.5.2 WWE_2_1_.15.502.3_6275_1.40.30.00
Oli SPL 1.40, OS, Ext Rom, and 1.40 radio
http://forum.xda-developers.com/showthread.php?t=302092
4. after that I'm stuck @ tricolor screen with IPL 1.03 and SPL 1.40.Olipro
5. Used mtty without problem.
Cmd>info 2
HTCSSuperCIDHTCE
Cmd>info 4
HTCSCWS__001Ùü¤HHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1D500
Partition[3], type=0x4, start=0x20500, total=0x1A300
CE Total Length(with sector info) = 0x41A2800
CE CheckSum Length(without sector info) = 0x40A0000
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x91BAA20E
CE CRC checksum = 0x91AAF967
ExtROM CRC checksum = 0x8026B8EF
Radio Image CRC checksum = 0x967D13F3
5. Tried flashing with POF's unlocker v3 from SD flash successful.
I can flash with any rom from cingular's original wm6 to any rom without
any problem but can't boot.
When I press power button, the screen goes blank and green light but does
nothing else.
6. I've have read all the thread from Dead Hermes to HardSpl stickies and
searched the forums for 2 weeks now but can't find an answer. The
problem is that I have to returned the phone in 2 days or cingular's billing
me for the phone.
7. I tried flashing 1.10.Olipro, 2.10.Olipro, etc to replace 1.40.olipro from sd.
I says each time successful flash but during reset it remains the same it
stuck in green light blank screen and when I enter the bootloader mode it
says the same IPL 1.03 and SPL 1.40.Olipro.
Thanks in advance. any help is greatly appreciated. I'm stomped.
Related
help me??????????
i can't down grade bootloader 1.09 to 1.04.(error:262)
USB>task 32
Level = FF
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a S024
Device Name: H, Bootloader Version : 1.09
Built at: Nov 7 2006 22:59:17
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B600
Partition[3], type=0x4, start=0x1E600, total=0x1C200
CE Total Length(with sector info) = 0x3DB3000
CE CheckSum Length(without sector info) = 0x3CC0000
USB>checkimage
IPL CRC checksum = 0x59C1EC20
SPL CRC checksum = 0x91BDD7D5
CE CRC checksum = 0xB5F30AD6
ExtROM CRC checksum = 0xDBC1AB54
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
My device is x01ht help me ????????????
welcome to the growing population of bricked TyTns because of the 1.09 bootloader. Send it back to HTC for main board replacement. Don't bother wasting your time, there is no fix for this problem. If you type info 2 in mtty you will see that your CID is corrupt. I have the same problem.
axiom said:
welcome to the growing population of bricked TyTns because of the 1.09 bootloader. Send it back to HTC for main board replacement. Don't bother wasting your time, there is no fix for this problem. If you type info 2 in mtty you will see that your CID is corrupt. I have the same problem.
Click to expand...
Click to collapse
Thanks....but how to "Send it back to HTC for main board replacement" ??
Contact the nearest service centre in your country.
pof said:
Contact the nearest service centre in your country.
Click to expand...
Click to collapse
but my device is x01ht(softbank),i flashed htcZ(NTT Docomo) rom ,service center is said "Not Proper item",so Outside repair .
Then you have a total brick
Probably in the future someone finds a solution for this... but now it's not known how to fix.
I suggest you to play with your bricked device, and probably can be the one who finds the solution
Thanks .... pof and axiom,
i while studying , repair this fix.
How to change my boot screen??
how to change my splash screen.(no cid && bootloader 1.09)
After trying to fix MapKing problem by flashing different SPL and OS, I have a new problem: shows "no gsm" then hang at windows mobile splash screen.
I have SPL 1.04, HTC_BOOT 1.08, and the wiki says "Flash a ROM with SPL-1.09+KITL enabled OS", but how do I know which OS has KITL enabled?
In addition, all the ROMs are now in RapidShare, and I have problem downloading. Could anyone please help share it in other places?
kuekpeow said:
After trying to fix MapKing problem by flashing different SPL and OS, I have a new problem: shows "no gsm" then hang at windows mobile splash screen.
I have SPL 1.04, HTC_BOOT 1.08, and the wiki says "Flash a ROM with SPL-1.09+KITL enabled OS", but how do I know which OS has KITL enabled?
In addition, all the ROMs are now in RapidShare, and I have problem downloading. Could anyone please help share it in other places?
Click to expand...
Click to collapse
You just need to spend more time reading the wiki...
trashcan said:
You just need to spend more time reading the wiki...
Click to expand...
Click to collapse
What I understand from WIKI is that all ROMs with SPL-1.06, SPL-1.09, or SPL-1.11 have KITL enabled. However, no ROM from Dopod has SPL-1.09 so I will need to flash the ROM from either HTC or Cingular. However, I'm worried that if I still can't get KITL mode, then I can't recover it myself using PB+KITL method. I understand that only SPL-1.04 has the CID bug to be able to flash other operator's ROM, therefore I would probably be stuck with HTC or Cingular splash, which will definitly void my Dopod warranty.
Therfore I will really appreciate if any knowledgable and helpful person could confirm with me that I should proceed to flash shipped SPL-1.09 ROM from other Operator to get KITL enabled OS, in order to use PB+KITL method to recover my bricked Dopod 838 Pro. If this is not a fool proof method, then I would rather sent the unit to Dopod Service Centre for repair...
I also posted in another thread asking for help ("dead hermes? corrupted radio? Post comments here" http://forum.xda-developers.com/showthread.php?t=286755&page=89), but have not got any reply yet...
Original Config: SPL=1.04, HTC_BOOT=1.08, Radio=1.38.00.10, ROM=Jasjamming WM6 v1.2.
What Happened: Flash by CustomRUU v4.2 Forced SSPL: SPL=1.04, HTC_BOOT=1.08, Radio=1.06.00.10, ROM=Dopod 1.23.707.4.
Current Problem: HTC Innovation Splash will show No GSM after few seconds, then hang at WM5 Splash. info 2 does not return SuperCID string anymore, and cannot boot into KITL mode.
Failed Recovery: Flash WM6 LVSW 2007-03-26 result in ERROR [262]:UPDATE ERROR.
USB>task 32
-> Level = FF
USB>info 2
->CID: Wait Interpreter timeout
HTCSUSB>
USB>info 3
->HTCSH
USB>info 7
->HTC Integrated Re-Flash Utility, Common Base Version: 1.50a
Device Name: H, Bootloader Version: 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version= 0x4
Main Board version=0x6
USB>info 8
->Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x0x1CD00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
Already answered in the brick thread.
Cuivienor said:
Already answered in the brick thread.
Click to expand...
Click to collapse
Thanks
while updating to XDA live frm Schaps, my JASJAM stuck at 51%, now it's showing tri-colour screen
i did mitty here are the details
Cmd>info 2
HTCSSuperCID HTCE
Cmd>info 3
HTCSH
Cmd>info 4
HTCS Lœ3ÆHTCE
Cmd>info 6
HTCST ÚÈÒHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1800
Partition[2], type=0x25, start=0x3100, total=0x1E500
Partition[3], type=0x4, start=0x21600, total=0x19200
CE Total Length(with sector info) = 0x43CB000
CE CheckSum Length(without sector info) = 0x42C0000
pls help me to bring my JASJAM to life..
Yes Did It! Yey!
i finally able to bring back my JAMJAM to life by this procedure!
1. Disable Activesync: connections -- settings -- uncheck "Allow USB Connections"
2. Take out battery, sim, and sd card
3. Look at your phone for SPL version. Mine was 1.40
4. Run RUUWrapper.exe on a ROM that you know would work. I used Scahps. Choose -2.02 bootloader option on the phone bootloader option.
5. Wait, don't hook up USB cable to your phone yet. Check the box where you're agreed to upgrade then hit Next
6. Now hook your phone to activesync and let RUUWrapper picks it up.
7. That's all. I guess if it didn't recognize your device at step 6, then I would try again if i were you."
and my JASJAM was working again!
1. problem started when trying to down grade cingular 8525 from Black Satin 2.10.Olipro for warranty return.
2. Used mrvanx downgrading guide to wm5.
3. Used the following Rom to downgrade:
New cing/ATT aku3.5.2 WWE_2_1_.15.502.3_6275_1.40.30.00
Oli SPL 1.40, OS, Ext Rom, and 1.40 radio
http://forum.xda-developers.com/showthread.php?t=302092
4. after that I'm stuck @ tricolor screen with IPL 1.03 and SPL 1.40.Olipro
5. Used mtty without problem.
Cmd>info 2
HTCSSuperCIDHTCE
Cmd>info 4
HTCSCWS__001Ùü¤HHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1D500
Partition[3], type=0x4, start=0x20500, total=0x1A300
CE Total Length(with sector info) = 0x41A2800
CE CheckSum Length(without sector info) = 0x40A0000
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x91BAA20E
CE CRC checksum = 0x91AAF967
ExtROM CRC checksum = 0x8026B8EF
Radio Image CRC checksum = 0x967D13F3
5. Tried flashing with POF's unlocker v3 from SD flash successful.
I can flash with any rom from cingular's original wm6 to any rom without
any problem but can't boot.
When I press power button, the screen goes blank and green light but does
nothing else.
6. I've have read all the thread from Dead Hermes to HardSpl stickies and
searched the forums for 2 weeks now but can't find an answer. The
problem is that I have to returned the phone in 2 days or cingular's billing
me for the phone.
7. I tried flashing 1.10.Olipro, 2.10.Olipro, etc to replace 1.40.olipro from sd.
I says each time successful flash but during reset it remains the same it
stuck in green light blank screen and when I enter the bootloader mode it
says the same IPL 1.03 and SPL 1.40.Olipro.
Thanks in advance. any help is greatly appreciated. I'm stomped.
Hi,
I have been working for days and nights through wiki (you guys do a great job) and reading forums on the issues of bricked hermes, and wanted to know am i wasting my time with mine as follows;
Dopod 838 pro (Hermes100)
IPL-1.01
SPL-1.09 (BEFORE 1.04)
Corrupted CID, IMEI, RADIO (NO gsm)
USB>task 32
CID: Wait interpreter timeout
Level = FF
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a S024
Device Name: H, Bootloader Version : 1.09
Built at: Nov 7 2006 22:59:17
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
USB>info 4
HTCSDOPOD001Û<wHTCEUSB>
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0xD(13) is BAD block !!!
USB>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x91BDD7D5
CE is None.
ExtROM is None.
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
spl-1.04 which allowed me to flash original roms but hung at 14%, i guess this is when the rom installs the radio part of the rom which mine was corrupt when trying in the first instance to update radio rom 1.54.30.10 which got me in this mess.
So its looking like service center i guess?
Were you flashing it at the time it stopped working? What is the history?
history i had a crc10.2 version rom, flashed supercid, flashed hardsplv7, then flashed original dopod shipped 3 rom 3.54.707.4 radio 1.47.30.10 worked great. Then flashed upgraded radio 1.54.30.10 and then bricked. Downgraded spl to 1.01mfg using mtty and then it corrupted my cid and imei. so now i left with a corrupted imei,cid and radio.
Did you use the "task 2a" command to fix bad blocks?
Might help....
task 2a command only works with mfg bootlooder eg spl-1.01 MFG, i cant go back to mfg 1.01 because your cid needs to be supercid. so my is answer no regrettably. iam thinking with spl-1.09 i could flash the factory rom via sd card? but where do you get factory roms from not upgrades considering my cid is locked.
There were a heap of roms on the wiki (dont know if they're still available) both cooked and stock roms. Who you with? Might be an idea to let people know as they might be able to supply links... Just a thought...Cheers
i am currently with 3, but i bought the phone used not sure who it was prior.
only a thought but are using a usb hub,if so stop and connect directly,dont know if my problems were exactly the same but 4 days of frantic flashing and stomach ulceration were instantly relieved by doing the above,good luck,btw the 3 rom from dopodasia is still available online and used with a mod wrapper would allow a card intall
i have tried hut..3 roms via flashing usb and by sd get error via sd not allowed. i guess the roms online are upgrades where i need the factory wm5 rom.
wm5 rom is a good idea and there are plenty stock wm5/6 roms floating around,but use the modded wrapper to install via usb,no hub,many people swear by at&t roms to get them out of trouble
thanks Stevie boy for your ideas and comments, still having problems i have tried all the dopod roms on xda developers using the custom RUU wrapper so i can select my spl which is spl-1.09 and i get invalid vendor id. if i had SPL-1.04 it has a bug where i leave the phone connected to USB and run the wrapper twice and it updates but this is not working now on spl1.09 bummer.
i feel your pain man,all i can say is that the wiki saved me,there is so much info there its a bit hard to see your way thru but you should be able to work it out.i assume you can still force bootloader is so it seems all is not lost try pm to mr vanx to get more specific advice
.....
I'm with the same problem...
can anyone give more advices...
_______________________________________________
Spv m3100
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a S024
Device Name: H, Bootloader Version : 1.09
Built at: Nov 7 2006 22:59:17
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
USB>task 32
CID: Wait interpreter timeout
Level = FF
USB>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x7725B228
CE is None.
ExtROM is None.
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0xD(13) is BAD block !!!
how to install???
hello guys,, since i am new with smartphones,, just bought a htc touch,, but don't knowq how to install the T9 pad,,
can anyone help me???
Is the HTC touch even a Hermes???
Me too, this posts seem no one able to fix it.
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x15E(350) is BAD block !!!
Block 0x184(388) is BAD block !!!
Block 0x1CF(463) is BAD block !!!
Block 0x1E8(488) is BAD block !!!
Block 0x2EA(746) is BAD block !!!
Block 0x2F3(755) is BAD block !!!
Block 0x311(785) is BAD block !!!
Block 0x364(868) is BAD block !!!
Block 0x3C6(966) is BAD block !!!
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x1CE00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
anyone can help ?
Try "task 2a"... Thats the command to fix bad blocks.
ultramag69 said:
Try "task 2a"... Thats the command to fix bad blocks.
Click to expand...
Click to collapse
Thanks for the reply, I tried tat too. nothing happend.
I tried almost everything, like cid unlocker, flash radio, flash back to original rom, flash from sdcard...etc..
Now trying to get the window platform builder.
You need to downgrade your SPL to 1.10 for those commands to work. If you haven't, nothing will work...
ultramag69 said:
You need to downgrade your SPL to 1.10 for those commands to work. If you haven't, nothing will work...
Click to expand...
Click to collapse
The problem is, I can't flash any of the rom. radio, hard spl, or others.