UnBrick the Bricked Hermes with "SPL 2.03 - IPL 1.04 - NO GSM - KITL Disabled"
There are many people have this kind of brick but still no solution for it.
I want to ask the mods to make this thread sticky so if anyone find a sulotion for this type of brick would post it Here.
Summary :
IPL: 1.04
SPL: 2.03
CID: NO CID (Request timeout on mtty.exe)
NO GSM
KITL Disabled
I have tested all the possible sulotions available in the wiki but none of the could help me unbrick my hermes.
P.S. : Please just post your sulotions here NOT your comments like "you should superCID your device first", "It's your fault to use telstra wm6",....
Has anyone found a sulotion for this???
You Pm-ed me asking what to do and i pointed you in the correct direction so why have you started this thread?!
Hermes Unbricking Thread
and
Wiki page: How to unbrick your bricked hermes
EVERYTHING you need is there, you just have to read.
Maybe You do not read my Pm!
I have read all the wiki and thread concerning my problem several times!
The simple truth is that some phones are unrecoverable and have to be sent off for repair. Yours is one of these situations and I very much doubt that this will change. More and more of the pioneering technical guys will have updated their Hermes to another phone and the much admired POF has not been seen since he was accused of stealing...
The tacit feeling is that there is enough information and utilities to prevent people bricking their phones (i.e HardSPL and Update from MicroSD card) so if you do find yourself in this unfortunate position and can not recover your phone then you have to bite the bullet, and be better informed the next time.
POF accused of stealing !!!!????
What's that all about?
I dunno if I have a the same problem, but a similar issue, and trust me I am "PC guys, AMD fanboy, A+ tech:"whatever you wanna call i, I am expanding my horizons and I got into the mobile PC world. Trust me I am NOT Google lazy, i have read and read and read and researched and cross-checked and tried literally everything. I am stuck, I know what is wrong with my Hermes, I know where it messes up, and I DO see threads in other sites with 99.9% the same problem I have and I see NO soultion or anyone who knows or Really wants to help, I feel for Koorosh we need help, I have come to terms if have to send it away to repair. That bugs me I got it Literally 3 days ago, and ONLY used the OFFICAL AT&T WM6 Rom to upgrade
on my bootloader all I see is this........
IPL: 1.04
SPL: 2.03
I have too see in my display
IPL: 1.04
SPL: 2.03
when i can flash radio 1% and restart device!
try it
i also had the same problem.i have resolved using rom update through memory card.look for it in wike section.all the best.try it with original rom that came with the phone.
this will not work in this site again no solution for bricked spl2.03 cid locked
biswajitghosh said:
i also had the same problem.i have resolved using rom update through memory card.look for it in wike section.all the best.try it with original rom that came with the phone.
Click to expand...
Click to collapse
Do you know to read micro sd flash not work when device is not superCID!!!
I maybe have the same issue.
From the HTC ROM I flashed my device to Shannix Grass rom, a few days later I flashed to Satin Black rom, so far so good. After that I want to flash back to Shannix Grass and my deviced crashed. While booting he stuck at the HTC screen.
I tried to hard reset, flash another rom (stuck and reset at 1%), flash the bootloader (stuck and reset at 7%). After the failed ROM flashing I get error 270 image is corrupted.
In mtty I tried to format the NAND, and tried the erase command, nothing worked.
How can I diagnose the problem further. Is it possible to see why the ROM update failed or why the OS won't boot? I did some monitoring with USB monitor but I didn't get results where I get some conclusions of.
---
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
(My device is Herm200)
wow , i have the problem too. i almost live in phoneless .
.
SOLVED !!!!!!!! my phone now works
If your device became inoperable like mine, because i had a failed ROM upgrade,and the device failed to power up i have good news for ya.
MY DEVICE info is as below.
Problem:
Phone does not boot up, and looks like a red brick.
IPL: 1.04
SPL: 2.03
(it always gave an error 206 at 1% of any ROM update i tried)
Solution:
I downloaded the official WM6 ROM from the HTC's website below,
http://www.america.htc.com/support/8525/software-downloads.html
Then reset my device to the bootloader screen.
(holding the 'ok' button and the 'power' button and then using my stylus to push the 'reset' button close to the USB port.
i then disconnect the USB cable from my phone, and the display showed 'serial'.
i then ran the downloaded file, and waited till the collecting information from phone window came up, then i connected the usb cable back to the phone.
it connected, and VOALLA!!!... it started the update.
at least its better to have a working phone(without all the custom stuff), than none.
I hope this was not booring( with all the detail and all), but i hope it will help anyone out there who's device wont bootup.
wow , congraution!
i will take the method. but i wonder should i have to get the "connecting time" in the right point, or the computer can't find my phone??
( hope u know what i mean?)
Um.... i cant say for sure
weyun0513 said:
wow , congraution!
i will take the method. but i wonder should i have to get the "connecting time" in the right point, or the computer can't find my phone??
( hope u know what i mean?)
Click to expand...
Click to collapse
Well.. i can't say you should wait 1 or 2 seconds, but just plug it in as soon as you get that screen. i hope it works for you tooo.
what was ur exact situation beforeu can unbrick ur phone???
IPL?
SPL?
KITL??
NO GSM ERROR?
what was the rom that has bricked ur device??
where did it stuck during the brick phase?
is that 1st splash,2nd splash,...??
This method did not work for me!!!!!
Try the Official Cingular ROM
koorosh_bsboys said:
This method did not work for me!!!!!
Click to expand...
Click to collapse
My Hermes "red hot brick" happened when i tried upgrading to aCRCs_PHKv12r8, from a Schaps_WM6Pro_Hermes_4.31_WWE_Full ROM.
My device is a Cingulat 8525.
The upgrade went to the tricolor screen, and after 1% , my phone magically went off. I tried powering on, but it went to the tricolor screen again showing
IPL 1.04
SPL 2.03
and underneath showed "serial".
me too i'm having the same problem....any experts out there that could help us?
Related
Heh apologoies for title but im really stuck and desperate for any help!!
I have been trying to unlock my Cingular 8525 for many hours now without any luck.
I bought it off ebay knowing it was locked because I had seen these forums and knew it wasnt too harder job. I live in NZ we have a compatible 3G network here (they sell these phones branded as JasJams).
Anyway I dont have a cingular sim card, only a Vodafone NZ simcard. I dont know if that is a problem for me or not...
My problem is that I get part way through the update process and the connection between pc and phone gets cut everytime at the same place.
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
It then gives me the button to select the Update button (Update the radio and bootloader)
So I click that, it gives the next screen, click next, tells you its going to take 10 minutes etc, so click next,
It then instantly disconnects the active sync connection and about a minute later I get an error screen saying the unlocker encountered communications errors.
I have been through this whole proccess 6 times now with no joy
Someone pleeeeeeeeease help me
Thanks
im willing to pay for a code all i want is a unlocked sim phone none of this radio stuff etc
try Wiki
http://wiki.xda-developers.com/
or alternatively
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Thanks but not really helpful, I have read the wiki through and through. I have tried that flashing HardSPL v7 and i get exactly the same problem.
PLEASE somebody help me
The only piece that is confusing is what to do once your done. The instructions say that you will be replacing your radio with a tweaked one to allow the unlock. After the entire process is done I assume you will need to have your favorite radio (1.40.3 in my case) handy to flash back onto your Hermes?
I also assume that flashing your favorite radio back to the Hermes won't lock it back again.
To be honest, I'd suggest going back to basics. You could try quite a few workarounds and end up doing this anyway..:
Reflash the original ROM your phone came with. Should be found easily via wiki.
Then you can start upgrading again.
If that's difficult, try flashing from your MicroSD card, which I've found never fails, having bricked my Hermes quite a few times now with my own cockamayme (sp) versions of ROMs that I've cobbled together from bits of code and chewing-gum.
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
amet said:
as far as I know you dont need to CID unlock before flashing.... With olipro spl and custom RUU updater you can flash anything on your phone....
laurasaur, after you have installed 1.4 olipro, use custom RUU updater
http://forum.xda-developers.com/showthread.php?t=298737
use the RUU updater with your choice of Rom.
or if yo want to unlock the device before
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
She want's to SIM-Unlock, not to CID-Unlock.
Do you use Vista? I encountered a similar problem with Windows Vista. Try a PC with Windows XP for the unlocking process.
ok my bad....
I've seen this issue with v1.4 Olipro. Upgrade bootloader to the latest Olipro 2.1 version then re-attempt.
ok thanks everyone for your advice but i am still screwed.
im not running vista.
i can not upgrade to olipro 2.1 because the upgrade utility always gets error 260 (update error) the update utility cannot connect to your PDA Phone.
I have now tried on 3 computers, my own, my parents and my work all resulting in the same thing.
I think now I will try and flash a WM6 rom onto my phone just using the olipro 1.4 and the custom RUU updater and see how I go but I dont have much hope
ok im currently updating the rom to wm6 as posted on the forums and oh my gosh i have a progress bar for the first time ever!! woot~~
um ok. now i have WM6 dopod version and fkn still sim locked someone help me before i throw my phone at the wall lol im going on holiday tomorrow and will have no phone for a week if i dont fix this in the next 3 hrs
Sim Unlock
http://forum.xda-developers.com/showthread.php?t=293665
laurasaur said:
On my bootload screen during the setup it says
HERM100 IPL-SSPL by Des
HERM100 SPL-1.09.ds
and then
HERM100 IPL-1.01
HERM100 SPL-1.40.Olipro
Then I tick the appropriate checkboxes, I HAVE to soft reset my phone here to get it to sync up with my PC again, I dont think this should be a problem though,
Click to expand...
Click to collapse
Do *NOT* soft reset your phone here, it is normal that activesync disconnects while the pda is in bootloader mode (activesync only works while OS is running). Just click "next, next, next" in the RUU and it will go fine.
woooa i think i love you Pof, I seriously do. Im not sure how I became such a noob at reading instructions but im sorry and thank you so much I now have progress bar
if you're short on time avoid any radio updates, they seem a bit hit and miss - its not worth upgrading then going away to find you've got a tossy signal!!!!
hope it worked out!
Hi all,
First of all I want to let you know that I did search the forum for a solution. In fact, I found a lot of workarounds but none of them actually worked.
Let me give some details about my problem: My Hermes was working fine. I was running the official WM6 ROM supplied by HTC, so no customized ROM here.
It was going fine until the WM frozed. Then I soft reset the device and after that I never got cellular signal again.
While booting the device I got the message: "no GSM".
First thing I tried was to flash a new radio ROM. In all the attempts the progress bar never moved from 0% and after a while I got the communication problem error.
Then I tried flashing a whole ROM. This time the progress bar stopped at 81%. Apparently in the first 81% it flashes the OS and in the last 19% it writes the radio. Anyway, I tried this a few times and never finished.
In fact, after every communication error message I got stuck in the bootloader screen.
The only thing that works is to flash a ROM WITHOUT the radio!!
Is there anything I can do to save my phone or am I condemned to use my Hermes as a phone-less pda?
I tried everything I found in the wiki/forums, but I couldn't find a working solution.
I suspect that the blocks of memory where the radio data reside got corrupted, could that be possible?
PLEASE HELP!
thanks in advance!
Chris
A similar thing happen to me several months ago. While on a call my phone froze and when I soft-reset it the dreaded 'No GSM' issue appeared. I tried flashing radios/full roms/etc, but nothing worked. I ended up sending my phone to the htc repair facility and they fixed it at no cost. (Other than not having a phone for ~10 days)
Thanks dang, but I don't have a HTC service center where I live (Argentina, LATAM)
I'm faithful that the people of this wonderful community will be able to help me.
Just for curiosity, where did you send your device? Is it in the US?
cheers
sounds like a hardware problem to me...
Hi, there! I found that a lot of us who have bricked our Hermes, don't have a responsive radio bootloader, so when they try to flash a full rom, the progress bar hangs to 13%, or 81%. This is because at that time the flasher is trying to enter the radio bootloader, but because it's corrupted, it hangs. Till today there is no known solution to this one. I'm far away from England where I bought my Hermes, so I'm not thinking to send it back for repair. I'm a programmer, so my knowledge may be usefull here. The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
How can I try that?
windshearx said:
The first thing I must know is if i can use the "lnb" command without being SuperCID. I mean if there is something like a Hard-SPL with an "lnb" command - (or renamed for security reasons). Maybe there is hope!
Click to expand...
Click to collapse
You can use 'lnb' in HardSPL without having a real SuperCID; however you will not be able to flash a radio with 'lnb' command. The radio chipset has its own bootloader, the and the SPL just acts as a pass-through sending the data directly to radio chipset through the s2410 UART.
I had one device with non-responsive htc_boot and tried all kinds of SPL patches to flash htc_boot again on radio, without success. The only known method to fix this is to take the BGA chip out with hot air and reflash it with special hardware, as it is not common to have this equipment at home, your only option is to send it somewhere to do it for you.
However, I don't want to discourage you to research on it, maybe you find something i didn't
I have a similar problem
I also have a NO GSM and corrupted CID but I can access KITL and use it with PB 5.0. and I followed this steps here but the phone doesnt boot completely. It stops just after the two boot screens on Black WM6 ending on a white screen and the debug window on PB after loading all sort of things begin showing these lines over and over:
@@@@@@ HUB state changes now @@@@@@
[HDC]HubStatusChangeThreadPN TRUE
[HDC]HubStatusChangeThreadPN FALSE
Is there any hope for me? I have the cingular 8525
thanks
Gents, do you think the solution presented in http://forum.xda-developers.com/showthread.php?t=280425 could help me?
Please advise.
thanks again
chriscec said:
Just for curiosity, where did you send your device? Is it in the US?
Click to expand...
Click to collapse
I sent it to the HTC service center in Texas, US.
I just got my replacement from ATT.. Had the same problem. Its a hardware problem.. I wouldnt waste anymore of your time.
first, i'm sorry for my english
I've the same problem with a V1605 (french SFR), i've tried every solution but flash radio doesn't work.
I can flash cooked os without any problem, but it's impossible to put official
It's only a pda now, it's better than a brick
My hernes use to be the same as you 'NoGSM'.I tried to install the official rom,but it 's not work at all.I called to service center ask this problem,so they said that it must be only changed the mainboard. That 's terrible!!!
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
otoro_315 said:
for ALL -that has NO GSM and stuck at OS boot,
please follow this link -
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
the link above help me to bring back my hermes alive (about four hours work).
Click to expand...
Click to collapse
That only works with phones with KITL...which I don't seem to have.
Sorry, how to config the phone with KITL and solve the no gsm problem.
No GSM but when sim inserted
Hi all, First sorry for my bad english.
I also have 2 bricked Tytn Hermes 200. Its not my personal ones Its my company's property, which pple were using this phones. So i'm facin with problem which many pple here having but with exception. both phones having no gsm error when sim inserted but without sim its fine. In other words , device info showing every info including IMEI when sim unavailable. And some times works with sim but after making few call and receiving phone hangs(not system) and goes off from network but anthena signal still showing few bars. I'm thinking maybe the radio hangs totally and goes off, and after soft restart NO GSM. I also tried many flashing upgrading those things nothing can really help me.
When im flashing original rom from HTC (the latest one HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108) its hanging on 12% and doing 3 or 4 times recovery , but its finishes succesfully. So what exactly happening in 12th%?. Maybe its started flashing radio and stopped on bad block ? But then why its finishes succesfully after few retry?. Ok so if any one wants to experiments on the phones except radio welcome. I'll help. And some can give me quick example of how to check bad blocks?.
Tnx.
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
otoro_315 said:
@akarandomjames -
#1. have you try the comm button+reset button hold for 2-3 seconds
#2. OR try the comm button+OK button+reset button hold for 2-3 seconds
anyway, i'm not sure if KITL is dependend on the ROM version. because when my device was in NO GSM status, SPL is 1.04, HTC bootloader is 0108, and lost SuperCID. Because of my device is still has SPL 1.04, i was able to load WM5 full ROM upgrade using WWE HTC English QTEK_001 2.05.255.1 01/17/07 version (ROM available on this site under HERMES Upgrade link), run it twice. once you have successful load the WM5 ROM then try to do step #1 or #2 above to get KITL USB display on your screen device.
Note: i don't think KITL mode is not available once your device is in Production Mode. anyone here can verify this?
Click to expand...
Click to collapse
My device is still SuperCID and I know I don't have KITL...I have SPL 1.04 as well and HTC Bootloader is 0108. I can't install any ROMs with radios as they will hang at 11/12%. I will attempt this "overload" method where it seems some people have had luck with it...after a few recoveries it just finally installs...but I don't think that will be the case.
If I can't fix this in a few days, I will most likely use my warranty or just wait for the Kaiser.
My variation of No GSM
I feel like I have problem 1A...where I am able to boot into OS but no GSM.
I am still SuperCID, SPL 1.04, HTC Bootloader 0108. Last known radio before corruption was 1.48.00.00. ROM where this problem occured: VP3G 3.60.1.
I was not even in the middle of an upgrade...just a soft reset after my phone ALREADY lost GSM capabilities during a tether session. It was stuck with no signal in Phone Mode...I put it in Flight Mode...then tried to move it back to Phone Mode and it wouldn't do so. I soft reset...and the no GSM stuck.
I tried to reinstall radio...many errors...stuck on bootloader. At first, OS's only were not installing as well but I got past that. Now I am able to boot into OS's with limited capabilities...and they will NOT ACTIVESYNC at all. Regardless of how old or new the ROM is. I tried older OS's that I knew worked in the past for me...but they refused to activesync.
Due to that, I am not able to install latest HardSPL 2.10Oli via SSPL. That seems to be the only way to do it according to my knowledge and what I've read. Maybe mtty was capable but I'm not sure. HardSPL 1.40Oli wasn't giving me any problems though, but I just wanted to have the latest one so I can avoid IPL damage.
I can only install anything if I start the device in bootloader...and I'm only limited to the OS since my Radio Bootloader seems corrupted.
I'm not sure what caused the corruption in the first place...but I feel annoying now posting on different parts of the forum with a problem that seems to be growing in the community.
Hi guys. Mass apologies for my stupidity, but here goes...
I have now spent over 2 days on this site reading all that I can, but I am at a loss and desperate for your expertise!
I am running a UK Tmobile Vario 2. I was having problems with the phone crashing constantly and not getting any signal at all so I installed WM6 yesterday hoping this would help. Its not crashing as much, but its still not getting any signal.
After reading loads of threads and posts all over the place (I have read enough WIKI to make my eyes bleed), I think I need to update the radio version. This is the information I can gather from my phone:
Bootloader info-
Herm300
IPL-1.04
SPL-2.03
I cant figure out how to enter commands in bootloader to gather any more info I tried the mtty.exe thing with no avail. When I go to "device information" it reads like this:
ROM version: 3.60.110.4
ROM date: 09/05/07
Radio version: SAYS NOTHING!!!!
Protocol version: SAYS NOTHING!!
IMEI: SAYS NOTHING!!
When I do a soft reset I get red letters and numbers appearing and not the "no gsm" message.
This is a 2nd hand phone off of ebay as my original phone was stolen. I have contacted Tmobile, but they refuse to help me as its not the original phone that I bought.
I would be most grateful for any help you can give me!!
Thanks,
April
OK, firstly.....flash hardspl.........instructions here
Next flash ANY radio......try version 1.48.00.10.
with the device booted up and synched with Activesync, download the radio ROM, unzip and run the RUUprogram (the only exe in the zip).
select autodetect, it should highlite SPL v2.10 and tick the "HardSPL?" box.
go through each screen and accept everything......the radio will be flashed.
Hopefully your device will work properly after this.
uh oh...
Thanks so much for your speedy response. Obviously I managed to screw this up.
got to this stage
"select autodetect, it should highlite SPL v2.10 and tick the "HardSPL?" box."
It didnt autodetect, so selected SPL v2.10 and ticked "HardSPL" box manually. Went through all the other bits and when it starts to do its thing it just sits at 0% then i get error message "ERROR 262: UPDATE ERROR. The rom update utility has encountered communication errors during the update process. THe program will guide you step by step to recover from the errors so you can continue with the update."
So I followed the recovery process instructions several times. Nothing has worked. Have tried restarting my computer and doing a hard reset on phone, and stuck with the bootloader screen reading IPL 1.04 and HERM300 SPL-2.10.01Olipro.
Manage to get back to this stage
"select autodetect, it should highlite SPL v2.10 and tick the "HardSPL?" box."
and go through the ticks but always ends up with error message 262.
SORRY!
Sorry to hear about your problems.
Was it the official T-Mobile WM6 ?
If so it was another 1.50 Radio!
I have same now!
http://forum.xda-developers.com/showthread.php?t=357275
I read in another thread try putting phone in fridge for 15mins first without the battery.
Good Luck
fridge vs. floor
Yes, it was the official WM6 from T-Mobile.
Im worried now that my limited experience with flashing, cooking, and now crying will leave me with a proper "brick".
I will try the fridge thing, if I ever get it to loads WM6 again but for the mean time, I will continue to throw it on the floor.
What do you mean by it was another 1.50 radio? I dont know what version I once had, but as suggested by mrvanx, I was trying to upload the 1.48.00.01.
Again apologies for my complete ignorance, but Im sure there are others that share my stupidity and will benefit from me asking goofy questions. If anyone else has any more simpleton advice on how to revive my poor phone, I would be much obliged!
Thanks,
April
The 1.50 radio bit; If it was the official T-Mobile WM6 upgrade, then your radio will have been 1.50 (I am pretty sure)
I dont know what else to do!!??
Ok since trying to update my radio from nothing to 1.48.00.01 and receiving error message 262 during the update, my phone now only goes into bootloader mode reading the following:
HERM300
IPL-1.04
SPL-2.10.0lipro
I have tried the following to bring it back to life (but not in any particular order):
- restarted my pc several times
- made sure my Windows XP SP2 was up to date
- made sure I had .net framework up to date
- hard reset on phone
- soft reset on phone
- leaving battery out overnight
- updating SPL to 2.10.0lipro (again) doesnt get to any percentage, just straight to error 260
- updating radio to 1.48.00.01 (again) - wont autodetect. tried radio button SPL2.10, then just force safe, then just HardSPL. each option dies at 0% then error message 262)
- reinstalling TMobile version WM6 (again) - dies at 11% - error message 262
I saw the post by pof "How to unbrick your bricked hermes" and the solution was to "Flash any radio in NBH format", but I cant figure out how to do that!? (I have tried clicking on the nbh file in the downloaded radio folder, but dont know what program to use to unload all the info. Have also looked at all the links on "Radio sudden death issue knowledge consolidation" and nothing has helped.
Sorry again guys, but can someone please help
If not, does anyone want to buy my brick?
alachlan said:
Sorry again guys, but can someone please help
If not, does anyone want to buy my brick?
Click to expand...
Click to collapse
Dude - there are enough bricks around these parts to build a 500 story repair centre! All we need is MS to merge their NT, CE and ME technologies into CEMENT then we can hold all the bricks together
Error 260 (comms error) is usually caused by using Vista without "fixing" it or Win2K/XP without the .net framework on it
Error 262 is USB port not available - turning hermes off and on (or removing the battery if that fails) at that point and putting it manually into bootloader usually cures that one then continuing with the flash.
Incorrect.
Its more than likely this Vario II was irepairably bricked before the TC bought it, the Radio upgrade is failing on a Tmobile official ROM (which includes a radio) and on a standard CustomRUU upgrade for the radio only.
A "checkimage" command in mtty would probabaly return a failed radio checksum and following on from that the mtty commands to get into the radio bootloader will fail (rtask a......then rversion).
Also there may be a corrupted CID on the device which again isnt good.
Ive seen these types of bricks MANY times.
Sorry dude, looks like your Hermes was a paperweight when you bought it.
Never thought of that - shameful given the amount of radio investigating I've done recently Too busy on 260's with part flashes from people not installing .net (also the amount of hits you should be getting to your vista guide now is scary!)
Still say we should collect up all the bricks and build a repair centre
Mikeapollo said:
.....the amount of hits you should be getting to your vista guide now is scary!....
Click to expand...
Click to collapse
73039 hits according to the site
Pretty much the only fatal brick now is a damaged radio/CID flash. If there was a way for Olipro/Pof/Us to flash a hardspl type package in place of the radio bootloader then it would be solid.
What type of mortar should we use?
mrvanx said:
73039 hits according to the site
Pretty much the only fatal brick now is a damaged radio/CID flash. If there was a way for Olipro/Pof/Us to flash a hardspl type package in place of the radio bootloader then it would be solid.
Click to expand...
Click to collapse
Yup.. Must admit I think that's the one thing that will not happen anytime soon as the interactions between bootloader, radio bootloader and the radio PLA/PIC is a tad complex... It'll be a very difficult thing to test and even finding a suitable vunerability is difficult - certainly beyond my abilities presently. Though the same was said 12 months ago about the No-Wifi issue and Olipro led some excellent progress in that area...
Mind you - the key to fixing CID/radio bricks is to educate the masses not to make them in the first place and not to just blindly execute whatever they stumble across - more of a challenge than rewriting the bootloader by hand on paper tape and almost as frustrating
Oh... as for Mortar... we could have a mass scrape of all that weird dirt stuff that "grows" under the "invisible-until-you-open-it" edges of the screens and around the battery cover and add a drop of water
Wonder if it's the electronic equivelent of belly button fluff?
does that mean its dead?
Thanks for all the entertaining posts guys. Just to clarify things, Im running XP SP2, and the phone did actually work for about 3 months until suddenly one day it gradually started dropping signal, until the signal vanished completely.
Are you guys trying to tell me that my phone is completely dead then? Could I have prevented this by knowing what the hell I was doing or was it a fault of the phone?
With regards to the mortar issue I think a combination of tears and sh*t would do. I think I would build a big wall around the jackasses who release products that arent completely stable but still charge us an arm and a leg for them. (excuse my grumpiness)
Oh and just wanted to say that since my vario has been out of action, I have been relying on the trustiest brick Ive ever owned, my XDA IIs. This thing has been dropped so many times and is held together with super glue, but it does the job and gets on with things, just not very quickly.
Thanks again for all the help.
alachlan said:
Thanks for all the entertaining posts guys. Just to clarify things, Im running XP SP2, and the phone did actually work for about 3 months until suddenly one day it gradually started dropping signal, until the signal vanished completely.
Are you guys trying to tell me that my phone is completely dead then? Could I have prevented this by knowing what the hell I was doing or was it a fault of the phone?
With regards to the mortar issue I think a combination of tears and sh*t would do. I think I would build a big wall around the jackasses who release products that arent completely stable but still charge us an arm and a leg for them. (excuse my grumpiness)
Oh and just wanted to say that since my vario has been out of action, I have been relying on the trustiest brick Ive ever owned, my XDA IIs. This thing has been dropped so many times and is held together with super glue, but it does the job and gets on with things, just not very quickly.
Thanks again for all the help.
Click to expand...
Click to collapse
By the sounds of it you might have a permenant brick but unless i had your device here and actually went through everything myself i cant be sure. take a read through the sticky thread above this one about unbricking......it will take some time to read through but you will see what techniques are used to try and revive the device.
when cid corruped with spl 2.03 and not have gsm no solution can not flash with sd card when you see that level=fff only when level=0 in mtty console can use sd card for flashing rom.
THIS TIME ONLY SOLUTION TO UNBRICK HERMES WITH SPL 2.03 NO CID AND IMEI -
SENT Imei-check to fix this ??
?
uuuummm....
Thanks mbsshop1302gsm for the response, but did I mention that I have limited knowledge on this stuff? So the more basic the instructions are, the better.
Thanks,
April
Hey, my phone is an At&t 8525 and after finally fixing the white screen problem and flashing hard-spl v7 and a couple of roms I bricked the phone when flashing the last touch flo rom. During the flash the ruu wrapper stopped and indicated there was an error. I did the recovery and it supposedly completed succesfully if I can remember right. When it reboot it would not get past boot loader. And thats where I am now, the phone will not get past boot loader.
I've tried every method on these forum I could found
SD card flashing dosent work, I get the 002..... error in red.
Flashing the factory an at&t rom dosent work either, gets the same error
\
As for as I know the MTTY method dosent work, I don't know how to type in commands into bootloader and when I type in 14 0 in MTTY nothing happens
KITL is not enabled
IPL-1.04
SPL-2.03
The phone does not boot into bootloader when I hit the power button, I have to hold the comm button, power button, and soft reset in order to bring up bootloader.
When bootloader is up and the phone is connected to the computer via usb bootloader displays usb on the screen and windows detects the device as an HTC device.
Again i've spent about a week and a half trying to fix this phone and I don't know what to do anymore, i've tried more methods than listed above I can't remember though. If anyone can give me a hint on what to do I would highly appreciate it. Thanks
P.S Can someone please tell me how you type commands in bootloader or MTTY
You DON'T have Hard SPL V7 installed..... Otherwise your SPL would be 2.10.
Connect the Hermes to the pc, make sure active sync has benn disabled - got to settings, untick connect by USB. It should register on the pc. Go to bootloader then run the .nbh file for your stock rom... Make sure its the carrier rom that it was shipped with. It doesn't have to be WM05 but it DOES have to be your ORIGINAL carrier rom. Let it run through, you may gewt lucky.....
If it works, INSTALL HARD SPL V7....... Makes it so much easier to fix then...
Good luck...
Thanks for the reply, much appreciated
I tried downloading and sd card flashing a stock rom from a list of factory roms of all Hermes that I found here on xda. It gave me the same error though. I'm not exactly sure which exact rom to download from that list either. Any more help would be appreciated, thx
Wow I feel retarded, I used the wrong factory rom. After I used the right one it worked perfectly, I now have my 8525 back! Thx so much man, ur the friggin man!
Congrats bro you got it atlast. good luck & take care your baby in future. try to help others with your experience.
Glad you fixed it mate, but if I were you I'd also make sure you have Hard SPL V7 installed. It is the safety net to help when things go wrong... Never gonna be 100% safe but better odds with Hard SPL V7...
SPL - 2.10 oli
Cheers...
Ok... Rejoining the 8525 Clan
Is this Forum still alive???
Been a while guys, figured I would break out the 8525... charge it up and see what kind of things are new in this community. Unfortunately, it looks as if the radio is bricked on it. Seems like it will install ROM's that the radio is not included on. NO GSM is on the boot display, which is strange as I was using this phone until I got the Tilt about 1 1/2-2 yrs ago. I was a hardcore flasher back then... every other day it seemed, so I know it has (or had) everything it needed like the Oli 2.10 SPL... but it seems like I cannot recover this radio issue.
I am messing with the different original OEM and Carrier ROMs hoping I can get passed the 11-12% mark, and I will let you know if something changes. Any idea if un-installing SPL 2.10 Oli, and then trying to walk back through the old SPL steps could help? I am just trying to figure out another way to get around this radio issue... or basically I have a PDA, no phone Damn phone hasn't been touched in like 2 years, you think it would be just as fine as it was when I took the SIM out.
Cheers
Can u plz tell me how do you fix the white screen problem ?????
kashifmehmood said:
Can u plz tell me how do you fix the white screen problem ?????
Click to expand...
Click to collapse
Please try searching before posting.
Your answer lies within
Thread closed
I want to help someone on this please , bcs HTC SPV M3100 when i'm trying to switch on phone was stuck on HTC logo and nothing more , i have try to put on boatloader mode and phone was going on bootloader mode three color screen and show this:
HERM100
IPL-1.04
HERM100
SPL-2.03
i'm trying with hard spl from Pof soft but error getting.
Can someone find a time to help me?
hallooo
experts please!
Hello haveri,
what ROM are you trying to start? I was stuck on HTC logo too, when I tried to start a ROM without installing Striped ROM first, which was highly needed. So I done hard reset(three color screen), and flashed again.
For starters, put in bootloader, connect to PC (1st untick "Allow USB Connections" in activesync) and run Hard SPL V7. Install it on your Herms and hope it works because otherwise you are in for a whole heap of hairpulling frustration...
If you get Hard SPL onto your Hermes then use the sd card method to flash a new rom...
You could have avoided this by doing a little research instead of going full pelt into flashing, you Hard SPL BEFORE you get into trouble, NOT AFTER....
Hi guys,
I have a similar problem with a T-Mobile branded TyTn from a friend of mine who thought flashing ROMs without putting device into HardSPL would be clever.
The devices has also IPL-1.04 and SPL-2.03 and from the bootscreen it looks like WM5 should have been installed. I also get the "NO GSM" message and I REALLY tried every fking method but without success.
I even created a Goldcard (and verified on another device it's working, level 0 instead FF) and tried to flash several ROMs (also Cingular WM5 ROM and original german T-Mobile ROM) but no luck.
I also tried to run HardSPL V7 but as far as I remember it just said it cannot connect.
Funny thing: HardSPL V9 DOES start flashing and on the PDA and the PC the bar shows 100% but some moments later it says "Could not update" (or something like that).
I even tried different mtty methods from several posts from the forum (erasing the NAND on different ways, qtek loader method with erasing the first blocks) but I'm really really frustrated now and I believe there is no solution here?! (device has no guarentee)
So, if someone has ANY hint or useful information write it down or send me a PM.
I gladly appreciate your help and hope for a solution!
Cheers
P.S.: I couldn't find any information saying Goldcard method works (or even exists) for Hermes. Can someone confirm it does really work?