Hello , i've an Orange SPV M3100 HTC and when i've tried to upload the ITA rom near the 81% of uploading the upload have a self crash !!! now i can'nt do nothing.... no hardreset or something !!! When i try to start i can see on display only The red-green-blu-white colours with derscribe : HERM100 IPL-1.01 !!! Please , help me for a new life for my Baby !!!
first on pc go to activesync settings and untick "allow usb connection". Connect to pc and run the install for the original rom (reboot into bootloader BEFORE connecting by holding power,ok button above the flywheel and reset with stylus, hold all buttons in to go to the tricolour screen. I know you're there already but this is now officially bootloader not a f***ed up boot). Theres a chance you will be able to fix it this way. No guarantees.....
Afterwards install Hard SPL on your "baby" so you increase your chance of recovery.
Hi, Thanks for your help ! I've tried but activesync do'nt show nothing . HardSPL cannot see nothing... the only thing i can read in the white stream of "baby" is the scribe change from serial to usb when i connect it to the pc .... Any idea ???
Install the Shipped Stock rom... It WON'T be picked up by activesync but that doesn't matter. Its registering that there is a usb connection so install the shipped stock rom.
DO NOT INSTALL ANOTHER ROM AS THIS MAY PERMANENTLY BRICK YOUR PHONE....
Thanks Mentore , i've a little problem more because i have'nt the original rom....Do you know where i can download it ? Migthy TTTT
hi, i've find it! ( I suppose...) >>>> Official Orange SPV M3100 AKU 3.3 update . It's a full rom official by Orange. I try now and i'll tell you if i kill me...
nothing............the program can't find via usb the baby......arghh
did you go to bootloader before trying - hold power, OK button above flywheel and reset with stylus, hpld all buttons in until it ets to bootloader ?
yes, before when i put the battery it's off, when you put in the battery is off , when you make a hard reset it's start in bootloader red-blu-green ecc. no usb connection display say " serial " , when in usb connection display say "USB" but nothing can find the "baby" in the pc-usb.....
one of probably solution i think is :WM5torage for find in usb , windows mobile 5-6 for read WM5torage and try to load original Orange rom . But i have'nt any 5 or 6...
Hold down the buttons I said on my last 2 posts to go to bootloader. Just resetting means you have a screwed up reset not bootloader reset...
Yhaooooooooooo!!! i've connect to a vista notebook and all black but with right red led on. After i've connected it to my xp desk and autoreboot the old rom.... mistery .....ghost..... bah, now is ok. Thanks overall , see next one. Ciao from Italy.
Cool, Glad you fixed it.
Related
Sorry for my english fisrt of all. When i upgrade wm5 to wm6 i lost the connection with the pc. Both s200 and pc stop to response. I restart the pc and now the ActiveSync can't recognize my device. To my pda now appears a white screen and i can't do anything on it. What can i do???
manolisf said:
Sorry for my english fisrt of all. When i upgrade wm5 to wm6 i lost the connection with the pc. Both s200 and pc stop to response. I restart the pc and now the ActiveSync can't recognize my device. To my pda now appears a white screen and i can't do anything on it. What can i do???
Click to expand...
Click to collapse
There is a WIKI for this, but I guess you're to much in a stress to search...
First of all, Allthough it looks like that connection fails on several moments, don't panic. That's only normal, just be patient after some nailbreaking minutes (or even more...) things will continue.
What to do with your device now? Put it in bootloader mode:
Press the Camera button and soft reset. It will startup with a tricolor screen.
DISable the "allow USB connection" setting within ActiveSync
Connect your device to the USB port of your PC
Run the WM5 RUU again that you were using for the "Step1"
And now, just be patient!! First it seems to stop at 80% but it will continue. Then it pauses again at 95% but don't worry. Eventually it will make it to 100%.
After that: do nothing, don't touch nothing, just start the "Upgrade.bat" from the "Step2" folder. That will take some time to before it finishes, but it will. At last, DON'T FORGET TO MAKE A PROPER HARD RESET!
Rondol1 thank you. You don't know how helped me now. I lost ten years of my life. It works, thank you.
manolisf said:
Rondol1 thank you. You don't know how helped me now. I lost ten years of my life. It works, thank you.
Click to expand...
Click to collapse
You'r welcome, I spoke out of experience......
hahaha, I remember my first wm6 upgrade that went wrong , i freaked out the same way
hma4 said:
hahaha, I remember my first wm6 upgrade that went wrong , i freaked out the same way
Click to expand...
Click to collapse
Me too .. Guess thats just normal.. Upgradnig to a hole new operating system makes you think that it is critical to your pda's life.. And when it goes wrong you think your pure prophet is gone..
manolisf said:
Sorry for my english fisrt of all. When i upgrade wm5 to wm6 i lost the connection with the pc. Both s200 and pc stop to response. I restart the pc and now the ActiveSync can't recognize my device. To my pda now appears a white screen and i can't do anything on it. What can i do???
Click to expand...
Click to collapse
I advice u following this way:
1 - U unplug the battery for few minutes, then plug it into ur device
2 - Charge ur battery until it full (about 2 hours). Note: DO NOT USE USB_CHARGE, just use the adaptor.
3 - Uninstall the current Active Sync, then install the newest Active Sync from Microsoft (ver. 4.5)
4 - Turn on ur Prophet, then make it in the Bootloader status, connect with PC, up the step 1 (from PDAViet). Be patient until it complete.
5 - Continue with any step 2 u like.
Good luck.
Me ! Help me pls ! Stuck in bootimage and Win
My Xda Neo, it's stucked WIN, now it appeared bootimage blue ---> Align Screen --> Win ---> hang ---> and not connect with PC by active sync " LED always ON " ).
I used J A F tool may saved myxda but i couldn' do anything ( Stranged " I can up any rom by J A F and Active Sync )
I changed from 2.20.0001 to 2.13.0001 and 1.00.0001 and more but it's not still work now. Although I downgraded but IPL/SPL not changed 2.20, only changed OS ???
Who can show me how to resolve ! Pls help me !
Thanks !
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
p.s srry for my bad english
Did you rename it to eboot.nbo ? Have any files in root folder of your miniSD ?
Who make you try this way ???
i rename as i mentioned above with the long name only change the .nbf to .nb0
i also regret now coz cant even see anything from the screen >> althought tried reset eith all the mothod..
izzit my 6828 dead ad?
cant even repair by myself and have to send it back to hp for repair?
williamSun said:
i rename as i mentioned above with the long name only change the .nbf to .nb0
i also regret now coz cant even see anything from the screen >> althought tried reset eith all the mothod..
izzit my 6828 dead ad?
cant even repair by myself and have to send it back to hp for repair?
Click to expand...
Click to collapse
If you don't rename to eboot.nb0 => Your device didn't flash it => Your device not dead. Have another files in the root folder of miniSD card ? List for me!!!
--Try this way :
Press both softkeys (two "-" keys) and remove battery then insert battery again (don't unpress two softkeys) and softreset, wait 2-3 seconds. It'll go bootloader mode. You can flash your device again.
hmm, tried u way ad didt make it to boot screen..>.<
in case i rename to eboot.nb0 >>i not really sure<<
>>izzit case sencetive?
>>izzit 6828 dead??
williamSun said:
hmm, tried u way ad didt make it to boot screen..>.<
in case i rename to eboot.nb0 >>i not really sure<<
>>izzit case sencetive?
>>izzit 6828 dead??
Click to expand...
Click to collapse
What is your current bootloader, 1.01 or 1.05 ?
If you follow that menthod but it didn't go to bootloader, your bootloader was dead.
You can send it to HP to repair, or try this way : http://wiki.xda-developers.com/index.php?pagename=DeadBoot
I recommend to sent it to HP.
while the PDA is still can open and bootloader screen
is 1.01
and im trying to use the EBOOT0502_MNT_01.01.03.nbf which found in the
HP official RUU PC flash ROM
and rename to EBOOT0502_MNT_01.01.03.nb0
then put in the root of memory card
then start to flash ..
now the PDA wouldn't reapond to any button HR, SR, soft-key + reset ...etc
only can charge and orange LED indicated
williamSun said:
while the PDA is still can open and bootloader screen
is 1.01
and im trying to use the EBOOT0502_MNT_01.01.03.nbf which found in the
HP official RUU PC flash ROM
and rename to EBOOT0502_MNT_01.01.03.nb0
then put in the root of memory card
then start to flash ..
now the PDA wouldn't reapond to any button HR, SR, soft-key + reset ...etc
only can charge and orange LED indicated
Click to expand...
Click to collapse
You was flash wrong bootloader due to make your device dead.
Now you need restore bootloader.
If you send to HP, they will replace board you must pay for it.
But you try the JTAG menthod to restore bootloader it'll make your warranty expired.
thx for all ur answer, i really appreeciated.
btw, for sure hp center will replace a board in it and that will be expensive rite?
if i sent to other shop which is not HP official service, will they do the same?
izzit juz flash using tools they hv>?
and expensive?
Here is what I did ... might help you
Hi
Make sure your phone is powered, it would be wise to charge the phone via AC power at least for 1-2 hours before you try to install anything.
I finally managed to install WM6 on my HP ipaq rw6828. But it wasnt easy, it took me 1 full day to get it installed. Just to help other people who are installing this, here is my experience -
What all I did and how I finally got there -
1.
Tried to install it via PC. When I already had a higher version of the Bootloader installed. Best way is to install it via 1GB mini SD card.
2.
After reading other posts I managed to downgrade the bootloader to version 1.0.1 (not sure of the version number...but its the version you get after installing the HP SP34074).
3.
Once I managed to downgrade. I got into the Bootloader mode on my device( its pretty simple to get into BL mode, make sure you ask someone to help you with it, its easier with two people, to get into Bootloader mode - a)press the two "-" buttons on the phone together. b)While the two "-" are pressed have a second person remove the battery. c) Wait for a few seconds and ask the person to insert the battery back. d)Once the battery is in place ask the second person to use the stylus and push into the soft reset hole (its hole on the left of the USB connecter on the phone). e) Wait for a few seconds and then phone should go into the BL mode. f) release the two "-" buttons after it enters the BL mode. Sometimes for me it entered the BL mode after I released the "-" buttons also. But dont release the "-" buttons till you have pressed into the hole with the stylus.
4.
With my phone now in the BL mode and showing the older version 1.0.1 (not sure but it should not be 1.0.5) I clicked the Device Software Update Utility.exe. I got the screen where you get a combo/dropdown with "ALL" pre-selected. The install step clearly says choose "OS" only and not "ALL". But I made a mistake here, for some reason using the mouse I didnt see any other option in the dropdown accept for "ALL". so I selected ALL and did a next. The setup kicked in and I got different screens showing status of install. But on the final screen it got stuck at 6% and stayed like that for well over 6 hours...I didnt touch the install as the instruction clearly say not to disconnect or stop the exe. But after 6 hours I realized that something is wrong and i killed the Device Software Update Utility.exe file.
5.
I did a soft reset on the phone and to my surprise after a while it loaded WM6....but that was it. Has the install failed in between the WM6 on the phone was totally screwed up...nothing worked properly. I coudnt even get ActiveSync to recogonise my device or connect to it.
6.
I tried the whole sequence mentioned in step 4 again but no luck now Device Software Update Utility.exe would error out I assume it could be because of the BL version 1.0.5. So I thought let downgrade and install the older BL version....but with no active sync i coudnt downgrade the device.
7.
Then i read somewhere SD card boot method to copy the EBOOT0908_MNT_1.00.05.nbf from the SP34074 and rename to eboot.nbo. This didnt work either, am not sure if I renamed the file correctly to .nbo(Orange) or .nb0(zero). Well I dont know whats correct eboot.nbo or eboot.nb0. But since this step didnt work. I was really upset as I felt I was stuck...then GOD had mercy on me and I did something which simply worked ...
8.
I took my mini SD card out connected to my Laptop in the SD card slot with the SD adapter. Did a quickformat to clean it up...if you have data its a good idea to back up the SD card in a seperate folder.
9.
Now I had a clean SD card with no files I downloaded the 1.0.5a (for 68x8) for miniSD. I copied the diskimg.nb0, size : 64,000 KB to the SD card root folder.
10.
Since I was trying the SD card method, I connected the mobile to AC power instead of the PC just to make sure I had enough power for install.
11.
I popped the SD card back into the phone. Removed the phone battery. Then entered into the Bootloader mode (refer to step 3 for getting into BL mode). Well nothing seemed to be happening...but I decided to stay on the BL mode .... to my surprise after 10-15 min i got a message asking my reset and goto factory mode. I wasnt sure if it was asking me to do something or was just a message. While I was wondering...the phone restarted automatically and it loaded WM6 ..asked me to do the tap thing to configure like the initial factory setup .. after all this I poped my SIM inside. Connected the phone to my PC. Active Sync finally recognized my device and synched everthing. Now everything WORKS!!! Though there are some issues like the camera flash doesnt come on.. etc but more or less everything seems to work. I havent tried other applications like email SMS wifi bluetooth etc.. I will post soon my experience weather all main applications work without a glitch...but am so happy my patience paid off..
Thanks to nhocbanme for WM6 version for HP ipqa rw6828, my biggest mistake was not to properly follow steps listed by nhocbanme. For people trying to install WM6 on HP ipaq rw6828....please please use the SD card method...it works and takes less then 30 minutes...you can follow my steps 8,9,10,11 to have a trouble free setup.
Good luck
Amit Reddy
Hi... my bootloader is dead any I cannot locate the fin out to flash my ipaq rw6828... please tell me where exactly are the pin out for rw6828
Thanks you.
Hi WilliamSun,
if you can go to boot loader it mean you can repair your device. You should download WM5/WM6/WM6.1 ROM that design to flash via mini SD. you can download it from nhocbanme's or hellowordl1's thread, and flash your device again.
Good Luck.
HELP
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
in this case i cant solve my problem
downgrade with SP34074 from PC (like intruction on screen PC)
1. run SP34074 from PC
2. remove battrey from device for sec, and put back to device
3. connect the device via USB, n make sure the PC is respon that
4. follow the instruction in screen
its work for me
Guys i tried to upgrade my imate jasmin, to wm6 the problem was that it started to upgrade the rom but the process was interrupted, when i tried to turn it on again it does not pass the initial blue screen that gives the info of the rom. The active sync does not work because the PDA does not connect to the computer and doesn´t pass from the initial blue screen.
Is there anything you can do, or the PDA is to the trash.
Hope you can help thanks. http://forum.xda-developers.com/images/smilies/confused.gif
Which Rom
Which ROM you use?
well i used the rom that is the upgrade for wm6 that is on the portal, the one that is for prophet, but the upgrade didn´t reach the end and now the pda does not pass from the blue initial screen and it isn´t possible to achive any type of conection to the PC i don´t know what to do...
deltav13 said:
well i used the rom that is the upgrade for wm6 that is on the portal, the one that is for prophet, but the upgrade didn´t reach the end and now the pda does not pass from the blue initial screen and it isn´t possible to achive any type of conection to the PC i don´t know what to do...
Click to expand...
Click to collapse
Bro. Try the methode found in the sticky:
FLASHING TOOL For all nk.nbf (WM6.1), 3 color bootup? SOLUTIONS ... in
http://forum.xda-developers.com/showthread.php?t=353547
In ur case, although the connection seem disabled, we could still force the activesync to work for flashing. Just right click the activesync icon in lower right corner of ur pc, choose connection, force it to search the usb. retry once or twice if u r not sure, then try to reflash the rom while the activesync seem still searching for devices. If it won't start, then the better way is to follow the step from Dioxda2 above. If it started halfway as before mean u have to re download the rom with its all suitable methode such as Hardspl, jumpSpl etc.
This work on my Dopod 818pro while stucked on 3 colour bootloader screen. Hope it will work on ur case too. Good luck.
thanks bro, hope it works, i will tell you later if the pda is back online
deltav13 said:
thanks bro, hope it works, i will tell you later if the pda is back online
Click to expand...
Click to collapse
Hi again, bro. Any progress? Good luck.
[img=http://img444.imageshack.us/img444/2017/dscn1600br9.th.jpg]
you will need
microsoft activesync installed on your windows pc
download ubrhurricane.rar from rapidshare HERE (link dead use this one)
http://www.megaupload.com/?d=JLO5H1L7
unrar this to your desktop.
to unlock go to the unlock folder and copy the cert.cab file to your phone using activesync and run the app from your phone. if your phone wont run the file then use the SDA_applicationUnlock.exe.
in the unlock folder you will find SPVServices.exe click SIMLock Tool and let it do its magic, after this click CID Tool. This will set your phones CID to 1111...
your phone will now be unlocked
we will now patch the ruu,
you will need to turn your phone off and hold the camera button whilst putting the usb into the phone. this will turn it on and show you a three colour screen. go to the spl folder use Patched_RUU.exe to flash your phone, after the bar has reached 100% you can unplug the phone. and turn it off.
now, use as.exe to kill microsoft activesync and then double click on MMTY142.exe this is what we will be using to flash your phone.
do the same thing we did before, hold the camera button and it will show you a 3 colour screen. but this time it will say
need an I U(0)?
make sure you select Y. (youwont see a N) you might need to do this a few times to get it right.
click the usb button and then it will show you a terminal which you will then type:
info2
this should tell you that your phone is SUPERCID (if it isnt then go back and unlock again otherwise the rest wont work)
now type
format BINFS
after that you will then need to tell them where the rom is, we will be using 413.bin which is selang09's wm 6.1.
type in
l c:\thefilepathtoyourdesktopgoeshere\ubrhurricane\413.bin
this will then flash your phone and you can turn it off after it says its complete. if this fails then just try it again its probally because you didnt get a Y at need an I U(0)? )
you can reboot and you will see your phone with wm 6.1 when it boots up it will be in the chinese language. this can be changed by pressing start, 6, 0, 2 and then select US English.
install t9 english.cab using activesync onto your phone to sort out the chinese keypad.
you will now have a working wm6.1 in english with an english t9.
at the moment selang09 413 wm6.1 rom is the best i have used. its VERY RELIABLE.
htc hurricane 4 ever
ps, use www.skyfire.com
Link not valid anymore.
Could you reupload ubrhurricane.rar
http://www.megaupload.com/?d=JLO5H1L7
sweet! just flashed it yesterday and it seems to be working fine.
I'm glad to see someone is still active in this part of the forum. been awfully quiet around here lately.
Hello, what other languages are there in the ROM? Any known problems?
only chinese and english mate, no problems. do rember to install the english t9 or one for your own language. everything works cheers.
Unlockable
I just get "phone is unlockable" message when trying sda_applcationunlock.exe.
On an orange UK g only sim c550 with vista and active sync active
Tried on XP and vista.
Anybody any thoughts appreciated.
are you sure you have copyed the cab file to your phone and its executed? then run the exe..?
is it a chinese rom?
hey guys, now i am tried 3 diffrent roms and always it is in chinese is it right.
may i change the language or do i need an english rom?
how can i change the language?
where i can find an english rom?
thanks a lot
lessew
ubrdave said:
click the usb button and then it will show you a terminal which you will then type:
info2
Click to expand...
Click to collapse
Hi there, i think there's meant to be a space between 'info' and 2,
e.g. "info 2"
cheers!
Definitely a space between info and 2
Couple of other little things that might be worth editing in your fine original post...
do the same thing we did before, hold the camera button and it will show you a 3 colour screen. but this time it will say
need an I U(0)?
make sure you select Y. (youwont see a N) you might need to do this a few times to get it right.
Click to expand...
Click to collapse
You might want to make ultra clear that we need to press 0/zero at this point, I was stumped for a while, tried pressing every key...
click the usb button and then it will show you a terminal which you will then type:
Click to expand...
Click to collapse
You might want to clarify this is the USB button in MMTY142, as I saw USB in the bottom left corner of my phone, and kept trying to press the left soft button instead.
Finally, to reassure people that nothing is wrong, they will need to restart after selecting US English as the language, for all menus to not show Chinese any more.
Thanks a lot for putting the guide together, I've had to go back to my C550/Hurricane after I cracked the screen on my Kaiser - I was getting annoyed with so few new/useful apps working on WM2003SE / pre-NET CF3, and had still had a backup-backup phone in the form of my SE K700, so decided to give WM6.1 a shot. Off to try and install PockeTwit now
Hi, my phone totally dies before I ran the Patched_RUU.exe; it just don't turn on or do anything else. Can you tell me something to bring it back?
Sorry, I don't know the answer, but others may find it useful to know if your phone won't enter the three colour screen, OR just won't turn on normally?
Just to confirm, what happens if you hold down the camera button on the side, then connect a (known working) USB lead between it and your PC? And if you connect your phone to a mains charger, does the orange LED light up to indicate charging is taking place? Any other previous symptoms with this phone?
SilentlyScreaming said:
Sorry, I don't know the answer, but others may find it useful to know if your phone won't enter the three colour screen, OR just won't turn on normally?
Just to confirm, what happens if you hold down the camera button on the side, then connect a (known working) USB lead between it and your PC? And if you connect your phone to a mains charger, does the orange LED light up to indicate charging is taking place? Any other previous symptoms with this phone?
Click to expand...
Click to collapse
Hi;
The phone is totally dead (No three colors screen, no ligth on, no nothing).
If I hold down the camera button on the side and then I connect a (known working) USB to the PC; guess what... yes! Nothing Happens!
If I connect the phone to a main charger then the orange LED light up.
If I remove the battery and then put it back again and try to turn it on the LED light up in red (it blinks just once).
Could anybody help pleeeeeease!!!!
THX
Hi,
I have a problem with the flash:
After "info 2" I get this:
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
HTCSSuperCID ' HTCE
And then nothing happend with "format BINFS"
What's the problem? I did something wrong? I tryed again with the unlocking procedure but it happened everytime!!
PLS HELP GUYS
You sure choose "Y" when you've been asked for UI interface.
You sure unkock your hurricane I'm mean Sim, Cid, SDA Applicattion.
Hi,
Yes I did! I used the spv tool for it, but no way to pass the "info 2".
Why?!?
Help Please
info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0xF400000 Bytes
HTCSSuperCID ' HTCE
Cmd>format BINFS
Format BinFS partition.
Format is completed!!
Cmd>l c:\rom.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImage "c:\rom.bin"
:F=c:\rom.bin
start download
SHAddress 82040000h Length 02630000h
Before flashing new image , formatting old OS is completed!!
Start flashing new image!!!
*checksum = 0, skip checking
OEMFlashWrite(82040000h,8C080000h,01C00000h)
Update BINFS offset 0x00000000 length 0x01C00000 ...
WBinFS D=0x0 L=0x1C00000 CS=0xD3D7666A
WBINFS from S 0 l=29360128 57344 SS
ReadB A=0x0 L=0x1C00000 CS=0xD3D7666A
Update BINFS success.
2nd download dwVaddr=0x8C080000
*
Then it hangs for5 mins and mtty says about being idle for 5 mins? is it still flashing please can someone help thankyou
thanks for giving me a tutorial that help me
efficiently BRICK my hurricane in less then 2 minutes!
yay!
Followed instructions precisely..
after i did the "patched_RUU" update..
BRICKED.
bullshi*.
oraeanast said:
thanks for giving me a tutorial that help me
efficiently BRICK my hurricane in less then 2 minutes!
yay!
Followed instructions precisely..
after i did the "patched_RUU" update..
BRICKED.
bullshi*.
Click to expand...
Click to collapse
What an ungrateful & rude person you are. YOUR phone was bricked when YOU decided to try something on it. No-one forced you to attempt it.
As you may have guessed from other responses here, most of us have flashed this and other ROMs with no problem.
Is it definitely bricked? Have you tried various recovery techniques.
Have you previously tried asking for assistance in a non-confrontational manner, or even just asking for assistance?
The problem I have is that my HD2 used to last for about 48hrs, but after playing around with it as we do with roms! the battery life suddenly drained in hours.
Battery used to last about 48 hrs with a charge time of less than 2 hrs. It then started to last 8hrs with a 4hr charge time, now it lasts 6hrs.
This is with all apps turned off no data connection, only sending txt and quick calls during the day. 100% power at night and it will be dead by the morning!
I have removed all programs and gone back to UK t mobile 1.72 rom, with same results.
I phoned T mobile and they have been kind enough to send me another free battery to solve the problem but to no avail!!!!
I am now going to send it back to get repaired, however HSPL is installed and it is being a proper pain to remove. I have done searches and watched the utube clips, so please dont say use search, as I have done for 2 days now!!
My HD2 will not enter bootloader by the buttons, I HAVE to use the bootloader cab file and install it and do it that way. Next problem is when it asks me to press the power button to start update image, it does not respond to the power button or the down button to cancel! (have to pull battery of to restart)
I have tried lots of renamed ruu_signed files (uk t mobile and htc) on a FAT32 formatted SD card, same problem.
details are as follows
OS version 5.2.21889 (21889.5.0.87)
Manila version 2.5.20121429.0
ROM version 1.72.110.4 (86525) WWE
ROM date 04/02/10
Radio version 2.07.51.22_2
Protocol version 15.32.50.07U
Really need to get rid of HSPL so it can get repaired!!
Any ideas to this strange problem? Anyone experienced this aswell?
Thanks in Advance
AJ
run hspl2 and choose 1.66.0000
hspl gone.
Thanks for the quick reply!
I downloaded and tried to install HSPL2 from the search results.
I follow the on screen instructions, as it waits for a USB connection I get an critical error box appear on the laptop.
Flow: 00000001
Error code: 00000002
Description: USB Connect failed!
Freezes on the bootloader screen.
I have tried all 3 USB ports on the laptop and another USB cable to no joy!
Has my phone got gremlins crawling inside it or what!
Any help to save my sanity will be greatly appreciated!
Thanks
AJ
normally i would say enter bootloader manually then run hspl but you cant, so, let it fail, then exit hspl, leave teh phone in bootloader, and run it again. You can try over and over, different ports, whatever, no need to re start the phone each time, just leave it in bootloader and connect the usb cable.
As always, the following applies,
1 - right click hspl.exe and choose run as administrator
2 - dont use front mounted usb ports, or ports through hubs, DO use a port around back of the pc (i.e one connected to teh motherboard) EDIT - oh its a laptop, could be problematic, find a friend with a real computer.
Just cos a port works for active sync doesnt mean it will work for hspl, so keep trying ports.
If all else fails use a different pc.
Cancel last, it just worked!!!
Thanks very much for your help.
One question though, now that the spl is 1.66 and the original was 1.42, can they tell that the phone has been tampered with?
aussiejock said:
Cancel last, it just worked!!!
Thanks very much for your help.
One question though, now that the spl is 1.66 and the original was 1.42, can they tell that the phone has been tampered with?
Click to expand...
Click to collapse
you said you upgraded teh rom to 1.72, , well if you hadnt had hspl installed it would have upgraded the spl to 1.66.0000, which is why i said go for that one.
Thanks Samsamuel,
Everything is back to normal. I put it in for warranty repair yesterday, need to wait 2-3 weeks now!
again thanks for your help.
AJ
hehe, start marking off the days on ya calendar.