This thread is to answer the popular question of:
"How can I get my Fuze back to stock and be able to return it for warranty service?"
I've been able to find very convoluted instructions and containing unnecessary manual effort for no reason. I returned phones to AT&T and HTC w/o any problems and I learned the shortest method of complying with the expectations involved. The thread will contain pictures of boot-screens pertaining to the process so that people can use them for reference. There will also be pictures of the progress and the different variations of devices out there.
This is for AT&T Fuze ONLY. The concept, however, can be used on any HTC Touch Pro (GSM and probably CDMA) as long as you get the correct Stock ROM from the Stock ROM Wiki.
You only need to do this if you have HardSPL already on your device.
To get to the canary screen / flashing screen (instruction for Fuze press and hold power and volume-down then press the small reset button on the right of the charging hole).
OliNex 1.90 HardSPL will refer to OliNex HardSPL for GSM Raphael devices.
OliNex 1.90 Stock Warranty SPL will refer to software also obtained from the same thread as above.
Screenshots below show RAPH110 and RAPH*** - there is no difference, so don't concentrate on that.
If your phone is Security Unlocked and you feel that you need to lock it back up (optional), please look at the procedures in post #2. However, I feel that AT&T and HTC will not care if it's security locked or unlocked, the screenshots below with the unlocked verbiage is actually a replacement that AT&T sent to me already Security and SIM unlocked.
Tri-color RUU bootloader refers to the colorful screen seen when the device is booted into flashing mode. This is accessed by holding down the Power Button with the Volume-Down Button and pressing the reset button. Reset button is located next to the charger hole. A screen showing the RUU boot screen like below will come up.
For the AT&T "World Phone" boot splash screen, see this post, but splash screen should come with an AT&T ROM applied in the step #5 below.
YOU WANT YOUR DEVICE TO END UP JUST LIKE ONE OF THESE SCREENSHOTS BELOW.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
YOU ONLY NEED THESE INSTRUCTIONS IF YOU HAVE THE HARDSPL
LIKE PICTURED BELOW, OTHERWISE YOU'RE WASTING YOUR TIME.
Some Explanation:
The concern is the fact that my Fuze came stock with 1.95 SPL, not 1.90 that OliNex provides, so to return my device with 1.90 SPL was a problem for me. I am including OliNex's 1.90 Warranty SPL which I hex-edited to show 1.95 instead. The reason why I did that is in case the person forgets or screws up on flashing the stock 1.95 ROM as noted in the last step of the instructions below.
OliNex's HardSPL does not allow any SPL to overwrite it. This is the reason why you need to flash the Warranty SPL, to overwrite that write-protected HardSPL. There is something special about that OliNex Warranty SPL because it's the only UNSIGNED SPL that seems to be able to overwrite the HardSPL. When I tried to apply any of my extracted SPL's (repository here) it would not work, like the author mentions in large and bold edit and had a Moderator close his thread. However, once you're at step #4, you can then flash only a full Stock Signed ROM (original HTC basically) from step #5 or any other Stock ROM (full list). Whatever SPL is included in that Stock ROM from step #5, will actually overwrite the Warranty SPL applied in step #4. Just an SPL extract/dump cannot be applied to the device because they are not signed. It also cannot be done when the HardSPL is present because the HardSPL does not allow overwriting of itself.
Steps to return the Fuze back to STOCK:
Unzip the attachment called JZ_Fuze_WarrantySPL_1.95.zip to a new folder.
Run the EXE file to flash OliNex's 1.90 Warranty SPL. I hacked his file to say 1.95 (if HardSPL is NOT present on your device expect the flashing process to stop at zero percent w/o any progress, and ask yourself did I read bullet 2 at the very top!)
Get to the tri-colored boot screen by holding power+volumeDown+reset to verify that you see 1.95... you're not done. It should look like this... (NOTICE: THE LAST TWO LINES ARE MISSING WHEN COMPARED TO THE VERY FIRST SCREENSHOTS AT THE TOP)
Not done yet if your tri-color boot screen looks like this:
At this point, you're ready to flash the AT&T Stock 1.95 ROM which can be downloaded from here or here. If this is done correctly you should see the same tri-color boot screen as in the very first screenshot on top.
Props go out to: Olipro, Cmonex and mskip - thanks for the software and the insightful info!
Thanks!
JZ
Security and SIM Locked Info...
If your phone is Security or SIM Unlocked and you feel that you need to lock it back up, below is some info. However, I feel that AT&T and HTC will not care if it's security locked or unlocked, the screenshots below with the unlocked verbiage is actually a replacement that AT&T sent to me already Security and SIM unlocked.
SIM Unlocked: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security Unlocked: Allows you to flash radios from another device (i.e. Blackstone or Diamond) - It does other stuff, but this is all the casual user will use it for.
To check if your phone is SIM or Security Locked you need ATCommander. Below are the commands for ATCommander to check the status of those two things.
[email protected]?40 --- tells you if you are SIM Locked (all zero's is unlocked)
[email protected]?AA --- tells you if you are Security Locked (all zero's is unlocked or here)
1) Reset Call Timers to zeros (optional and needed!) AT command: [email protected]=270f,270f
2) SIM relock is not needed for Warranty Service, per Olipro.
3) Relock Security last with Secrelock.zip by running the EXE on the device. Or AT command to Security Lock: [email protected]=7,1
To SIM unlock your phone for FREE, call AT&T and say that you're traveling abroad and need your phone to work with another SIM chip, they will give you an unlock code!!! It will not look like the one pictured at the top of this thread, on the right, which says "Security Unlocked", but it will be SIM Unlocked. Keep in mind that a ROM can change your IMEI by the last two digits causing the need for a new unlock code from AT&T.
reserved post 2
reserved post 3
would you be able to do this hack for SPL 1.69 Raph 300 as well? That's T-Mobile
Dust2Dust said:
would you be able to do this hack for SPL 1.69 Raph 300 as well? That's T-Mobile
Click to expand...
Click to collapse
Once I explain a bit more, I think your need for a hacked SPL will disappear.
Basically, apply either my attached zip on post #1 or use the Warranty SPL from OliNex... this brings you to a level where you can just apply a STOCK ROM (which includes the SPL) and whatever SPL is on that ROM will overwrite the warranty SPL... simply use a ROM that has that 1.69 SPL version and apply it to your device.
JZ SmartMort said:
Once I explain a bit more, I think your need for a hacked SPL will disappear.
Basically, apply either my attached zip on post #1 or use the Warranty SPL from OliNex... this brings you to a level where you can just apply a STOCK ROM (which includes the SPL) and whatever SPL is on that ROM will overwrite the warranty SPL... simply use a ROM that has that 1.69 SPL version and apply it to your device.
Click to expand...
Click to collapse
would that be like the one I created but has not yet been tested?? As there is no dutch factory T-Mobile rom available other than reconstructed ones that only have OS.nb.
http://forum.xda-developers.com/showthread.php?t=504570
If so I am going to flash the thing and see what happens with radio and splash.
Great, keep it up!
Dust2Dust said:
would that be like the one I created but has not yet been tested?? As there is no dutch factory T-Mobile rom available other than reconstructed ones that only have OS.nb.
http://forum.xda-developers.com/showthread.php?t=504570
If so I am going to flash the thing and see what happens with radio and splash.
Great, keep it up!
Click to expand...
Click to collapse
Interesting method of mixing different ROM pieces, a little on the desperate side but I've done lots of desperate things with NBHtool.
The problem is the key-word that you see at the top of this thread, your ROM is not "SIGNED" which means that your ROM might not be able to be applied to the device at all.
JZ SmartMort said:
Interesting method of mixing different ROM pieces, a little on the desperate side but I've done lots of desperate things with NBHtool.
The problem is the key-word that you see at the top of this thread, your ROM is not "SIGNED" which means that your ROM might not be able to be applied to the device at all.
Click to expand...
Click to collapse
Thanx m8 , that is the feedback I needed and was asking for. I will take the spl out and try to flash and see what happens.
It is not that I am on the desperate side, I just want to get this over with and be prepared once I am desperate, which hopefully doesn't happen for a while anymore
EDIT: I took out SPL, splash and radio and it allows me to flash ! using the czech stuff, Flashing as we speak...
Finished in czech:
Hey Dust2Dust did you manage to make a warranty RMA ROM for the MDA Vario IV?
Part of the first post said:
if you want to security unlock your phone for FREE, call AT&T and say that you're traveling abroad and need your phone to work with another SIM chip, they will give you an unlock code!!! It will not look like the one pictured below on the right, but it will still be security unlocked.
Click to expand...
Click to collapse
I have to point out that what you just discribed is not security unlocked... but SIM unlocked. There is a difference. SIM unlocked (which is what you are describing) is where you can put in another carriers SIM card and still use your phone with 100% functionality. Security unlocked is when you can put another carriers radio on.
Just dont want people to get confused.
great thread
AdamNimrod said:
I have to point out that what you just discribed is not security unlocked... but SIM unlocked. There is a difference. SIM unlocked (which is what you are describing) is where you can put in another carriers SIM card and still use your phone with 100% functionality. Security unlocked is when you can put another carriers radio on.
Just dont want people to get confused.
Click to expand...
Click to collapse
Got it, thanks for clearing it up, I will correct it. Learn something new every day
Questions though:
SIM Unlock is something that you need a "code" for from the phone vendor another carrier's SIM can now be used, correct?
Security Unlock will allow you to flash another device's radio?
HardSPL allows you to flash a non-signed OS, Radio & Splash? Or just a non-standard Radio (from another device)?
Security unlocking is achieved how? HardSPL? So, security unlock=hardspl/softspl?
OliPro used Security/SIM/CID unlock in this thread title, do all three mean the same thing? Or will OliPro send a different activation code for each feature?
secrelock.zip that I reference in the first post is to re-lock the Security Unlock? Or SIM unlock?
On my first screenshot, top-most phone pictures (on the right) says "Security Unlocked" and I received it this way from AT&T warranty, which feature is unlocked on the device, Security or SIM? Seems odd that AT&T would send me a phone that I can flash any ROM to... (it does say security unlocked after all)
Anybody that knows please speak up, this is interesting stuff.
Thanks!
JZ
EDIT: per these posts (post1, post2, post3, post4) I definitely learned that SIM unlock is different from Security Unlocked. Two different commands in ATCommander:
[email protected]?40 --- tells you if you are SIM Locked (all zero's is unlocked)
[email protected]?AA --- tells you if you are Security Locked (all zero's is unlocked)
The phone that I have in the screenshot (with the white "Security Unlocked" verbiage) shows that I'm both SIM & Security UNLOCKED... the phone w/o that white band shows 1's for both settings so it's actually locked yet I do have a OliPro's HardSPL on it. I wonder if the white band is available on older devices.
JZ SmartMort said:
Got it, thanks for clearing it up, I will correct it. Learn something new every day
Questions though:
SIM Unlock is something that you need a "code" for from the phone vendor another carrier's SIM can now be used, correct?
Security Unlock will allow you to flash another device's radio?
HardSPL allows you to flash a non-signed OS, Radio & Splash? Or just a non-standard Radio (from another device)?
Security unlocking is achieved how? HardSPL? So, security unlock=hardspl/softspl?
OliPro used Security/SIM/CID unlock in this thread title, do all three mean the same thing? Or will OliPro send a different activation code for each feature?
secrelock.zip that I reference in the first post is to re-lock the Security Unlock? Or SIM unlock?
On my first screenshot, top-most phone pictures (on the right) says "Security Unlocked" and I received it this way from AT&T warranty, which feature is unlocked on the device, Security or SIM? Seems odd that AT&T would send me a phone that I can flash any ROM to... (it does say security unlocked after all)
Anybody that knows please speak up, this is interesting stuff.
Thanks!
JZ
EDIT: per these posts (post1, post2, post3, post4) I definitely learned that SIM unlock is different from Security Unlocked. Two different commands in ATCommander:
[email protected]?40 --- tells you if you are SIM Locked (all zero's is unlocked)
[email protected]?AA --- tells you if you are Security Locked (all zero's is unlocked)
The phone that I have in the screenshot (with the white "Security Unlocked" verbiage) shows that I'm both SIM & Security UNLOCKED... the phone w/o that white band shows 1's for both settings so it's actually locked yet I do have a OliPro's HardSPL on it. I wonder if the white band is available on older devices.
Click to expand...
Click to collapse
Here are some answers that I got from DaveShaw. He answers most of my questions. The only left-over question is secrelock.zip will lock both SIM and Security or just Security?
http://forum.xda-developers.com/showthread.php?p=3225507#post3225507
SIM: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security: Allows you to flash radios from another device (i.e. Raphael) - It does other stuff, but this is all the casual user will use it for
CID: CID unlocking is an old concept, nowadays you flash Hard SPL instead. This lets you flash any ROM, Splash or Radio (depending on sec unlock) to your device. N.B. the CID is the carrier ID (e.g. HTC__001). The stock SPL's only let you flash ROM's that match the CID in the ROM image with the CID on your device.
Also, SuperCID is an even older concept no longer valid on newer devices.
Help
I'm really new to all this and I need to bring my phone back in for warranty repair and I just need to replace the SPL. I downloaded your zip file, unzipped it and tried running the .exe in the folder. It started the program but gave me an error after the second screen saying that the updater couldn't open the requested file. I'm not sure what I'm doing wrong. Can you help me?
Kyireana said:
I'm really new to all this and I need to bring my phone back in for warranty repair and I just need to replace the SPL. I downloaded your zip file, unzipped it and tried running the .exe in the folder. It started the program but gave me an error after the second screen saying that the updater couldn't open the requested file. I'm not sure what I'm doing wrong. Can you help me?
Click to expand...
Click to collapse
This kinda stuff is not easy to troubleshoot remotely so I'll give you some pointers... take a picture of your bootloader so I can have a look. Also take a screenshot of the error you get (if on the computer) use print-screen key and paste into mspaint or MSWord...
From the sound of it, you do not have a HardSPL so you're trying to reverse something that you probably don't have activated.
Thank you for the guide.
I just flashed back to stock spl / os.
I have one concern, the screenshot from the Att fuze show Raph*** in the tri-color boot screen, mine however shows Raph110. Is that acceptable for a warranty exchange?
Thanks in advance!
trancer_84 said:
Thank you for the guide.
I just flashed back to stock spl / os.
I have one concern, the screenshot from the Att fuze show Raph*** in the tri-color boot screen, mine however shows Raph110. Is that acceptable for a warranty exchange?
Thanks in advance!
Click to expand...
Click to collapse
Yeah, you're perfectly fine... this is a quote from the first post:
Screenshots below show RAPH110 and RAPH*** - there is no difference, so don't concentrate on that.
And make sure to actually look at those screenshots (top-most) on the first post as you want to use them for comparison.
Also make sure to have the last two lines:
PCBID 0x80
RID 0x0
Huh I get both a one and a zero
JZ SmartMort said:
To check if your phone is SIM or Security Locked you need ATCommander. Below are the commands for ATCommander to check the status....
[*][email protected]?AA --- tells you if you are Security Locked (all zero's is unlocked
Click to expand...
Click to collapse
OK ran the software and not sure of the result.
Got for the AA run "@secu_flag 1 0"
So since I got both a one and a zero I'm not sure of the status.
webfrm said:
OK ran the software and not sure of the result.
Got for the AA run "@secu_flag 1 0"
So since I got both a one and a zero I'm not sure of the status.
Click to expand...
Click to collapse
You actually quoted my first post with the answer --- all zero's is unlocked... you have a 1 that means locked. Click the link too all zero's is unlocked from above... you would have seen your answer.
Related
i was gonna unlock my 8525 via pof's unlocker and downgrade solution when i read this post http://forum.xda-developers.com/showpost.php?p=1062526&postcount=7 I then figured it wouldnt hurt to just called cingular and see if they would give me the unlock code...i placed a call to cingular's international department and get them to send me the unlock code in less then 12 hours by telling them i was planning to go on a trip out of the country on sunday and what is the soonest i could get the code..i then acted like i didnt know anything about getting a phone unlocked and he recommended that i place international roaming on my phone yada yada yada..... i declined and asked if i would still be able to roam while out of the country.. he said yes... i said thats fine.. but i would also like to have the phone unlocked incase i would like to buy a sim and use it for making local calls in the country that i will be in.. he said sure no problem... he submitted a request and in less then 12 hours i had the unlock code in my mailbox... i hope this helps anyone on cingular trying to unlock there phone with no modding...
now the second part of this thread is relating to the bootloader versions.. now i know that my bootloader is 1.6.. is it necessary for me to still use pof's method in combination with the downgrade in order to supercid unlock my phone in order to flash the rom with different hermes roms even tho' my phones sim is unlocked....is it possible to use pof's file to supercid unlock and then reflash back the same radio with no patch and same cingular rom to have the phone back to fully stock out of the box with the exception of having it be fully unlocked with the sim and sid..... also.. .is the same necessary for flashing the radio with different versions??..from what i understand you can "unhind the ext roms to see them but not activate themm.. and in order to use the features in the extended roms do i need to be supercid unlocked in order to unlock the ext.roms??i have fit4cat tweaker installed already and it makes the changes making me feel like i am accessing the ext.rom features already... and if so when i cid unlock my phone can i just pick and chose the .cabs to install from the different options on the different roms... .. i am not in an area that supports Edge .. but when i am will it display so on my screen with a E? or is that a mod i will need to do as well.. and i also see a feature in fit4cat that enables hsdpa.. i thought my phone would default using the connectin if it was available.. am i wrong.. and the ptt hack that someone on this forum created as a .cabs.. do i need to have it supercid ulocked to use that as well...
im sorry if alot of you have answered these questions time and time again.. i have really tried to answer my own questions for the last 8 hours or so with reading the forums and wiki's.. after a while it becomes a blur...
Ps. when using mtty.exe and i hook it up following exact settings and instructions when it connects it says CLIENTCLIENT then i hit the I to type info and i get CLIENT again.. no prompt.. ??help<< i was not in bootloader mode...oops.. it worked fine after i placed it in bootloader mode
thanks in advance
Abe
honestabe said:
now i know that my bootloader is 1.6.. is it necessary for me to still use pof's method in combination with the downgrade in order to supercid unlock my phone in order to flash the rom with different hermes roms even tho' my phones sim is unlocked....
Click to expand...
Click to collapse
Yes, you need to patch the radio to CID-Unlock. It doesn't matter if the phone is SIM-Locked or not. This needs bootloader 1.04, you can have it by flashing cingular's 1.30 rom.
honestabe said:
is it possible to use pof's file to supercid unlock and then reflash back the same radio with no patch and same cingular rom to have the phone back to fully stock out of the box with the exception of having it be fully unlocked with the sim and sid..... also.. .is the same necessary for flashing the radio with different versions??
Click to expand...
Click to collapse
Yes, it is possible but you need to downgrade your bootloader to 1.04 for this, otherwise you won't be able to flash any radio (patched or not).
honestabe said:
from what i understand you can "unhind the ext roms to see them but not activate themm.. and in order to use the features in the extended roms do i need to be supercid unlocked in order to unlock the ext.roms??i have fit4cat tweaker installed already and it makes the changes making me feel like i am accessing the ext.rom features already... and if so when i cid unlock my phone can i just pick and chose the .cabs to install from the different options on the different roms...
Click to expand...
Click to collapse
You need to have a SuperCID phone in order to UNLOCK the extrom, this means WRITE to it (i.e. delete cab files you don't need and use it as storage space, or put signed cab files from other ExtROM). If your Hermes is not SuperCID you'll be able to unhide it, but will not be able to unlock it.
honestabe said:
i am not in an area that supports Edge .. but when i am will it display so on my screen with a E? or is that a mod i will need to do as well..
Click to expand...
Click to collapse
It will not display "E", and the previous hack used in HTC Wizard for this doesn't work on Hermes. It displays "G" if you are under GPRS or EDGE coverage and "U" or "3G" if you are under UMTS/3G or HSDPA coverage.
honestabe said:
and i also see a feature in fit4cat that enables hsdpa.. i thought my phone would default using the connectin if it was available.. am i wrong..
Click to expand...
Click to collapse
Cingular ROMs have HSDPA enabled by default, you don't need to use that option from fit4cat hermes tweaker (it won't hurt if you do it), but it is there because not all roms have HSDPA enabled by default.
honestabe said:
and the ptt hack that someone on this forum created as a .cabs.. do i need to have it supercid ulocked to use that as well...
Click to expand...
Click to collapse
No, you don't need SuperCID to use this.
honestabe said:
im sorry if alot of you have answered these questions time and time again.. i have really tried to answer my own questions for the last 8 hours or so with reading the forums and wiki's.. after a while it becomes a blur...
Click to expand...
Click to collapse
ALL I answered is in the wiki, but probably explained in a bad way because I am not english native speaker, I would be very glad if you EDIT the wiki and explain it better/clearer than it is, so other people like you can understand it next time they read.
one more question... if i flash back to the cingular rom that is a 1.6 bootloader after i have done this whole process am i still able to flash to whatever i want providing that i have flashed from 1.6 to 1.4 unlocked sim and supercid previously.. basically does this flash the cidlock back on it.. or must i keep the bootloader in 1.4 in order to keep flashing roms
On another note.. i read these forums all night for the first time and i want to tell you Pof that you are the most helpful person i have ever come across on ANY forum board and the xda members are lucky to have you here... also extremely intelligent... thanks
extremely grateful
Abe
The main reason to SuperCID your Hermes is to be able to flash "whatever" rom you like, without having to bother with bootloader versions. If you use SIM & CID unlocker v2a to make your Hermes SuperCID it will be SuperCID forever, so the CID lock will not be back anymore.
Basically, after your device is SuperCID you only need to go back to bootloader 1.04 if you want to be able to flash extracted radio-upgrade only, as this is not possible with other bootloader versions.
is the patch u put in the radio overwritten when i apply a new rom???
the radio file is included in the rom you flash right?
or you can just find the radio file and flash that alone??
does the radio flash require it to be hooked via active synch or dissable
i have gotten Error 120 country id error twice now trying to flash ur radio flash.. any advice?
i should be outa noob questions shortly..
thank you again
if all goes well(im in the process of this whole precedure as i type...30% now) i shall write this in the wiki in n00b language...
honestabe said:
is the patch u put in the radio overwritten when i apply a new rom???
the radio file is included in the rom you flash right?
Click to expand...
Click to collapse
Yes and yes
honestabe said:
or you can just find the radio file and flash that alone??
Click to expand...
Click to collapse
Yes, see wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
honestabe said:
does the radio flash require it to be hooked via active synch or dissable
Click to expand...
Click to collapse
It doesn't really matter, as the RUU will kill activesync anyway, but I always recommend to disable activesync and start the update from bootloader mode (tri-color screen).
honestabe said:
i have gotten Error 120 country id error twice now trying to flash ur radio flash.. any advice?
Click to expand...
Click to collapse
Follow all the instructions, read and read
honestabe said:
if all goes well(im in the process of this whole precedure as i type...30% now) i shall write this in the wiki in n00b language...
Click to expand...
Click to collapse
Thanks, that would be great!
And good luck with the flashing
presto everything is working fine all done..
when it gave me the error i just closed the flash and restarted it...(just like what it said to do in the "if your having problems flashing post"
ran ur unlocker supercid program.. and voila
anyway.. ill write up somethin real user friendly..
thanks again Pof
-abe
Hey abe,
thanks for the tip on getting my phone unlocked...It worked like a charm.
okay, being a newbie to the Softbank X01HT, I went through the forums, FAQs, and Wiki as much as I can...
anyway, i checked with imei-check in regards to unlocking my SIM; however, their method unlocks the SIM, as well as SuperCID the device. from what i undertand - SuperCID the device would void the warranty, correct?
this being the case, if i do use imei-check, is there a way to "undo" the SuperCID?
similary, i can also use a process that only unlocks the SIM, ie., pof's free unlocker... however, as ive read, this is NOT compatible with Softbank X01HT models released after December 2006. right?
in this case, are there any other ways to unlock the SIM?
----
on the other hand, all i need is to unlock the SIM (no need for a SuperCID) - if there are people out there who have a better idea in going about this, please teach me...
thanks in advanced...!!!
PS: here is my Softbank X01HT
ROM: 1.33.761.4
ROM Date: 11/10/06
Radio Version: 1.14.00.10
As far as I know once you supercid it can't be reversed. I believe that if you use the hard-spl to flash, supercid isn't required anymore.
Now onto the unlocking the sim. I'm also a little bit confused on the options available. Please one of the gurus here step in and offer an explanation
garydempsy said:
As far as I know once you supercid it can't be reversed. I believe that if you use the hard-spl to flash, supercid isn't required anymore.
Now onto the unlocking the sim. I'm also a little bit confused on the options available. Please one of the gurus here step in and offer an explanation
Click to expand...
Click to collapse
the way i would understand is that if imei-check.co.uk unlocker is used, there arent any issue or problems. can anyone confirm/verify this?
however, for my needs at least - all i need is for my X01HT to be SIM unlocked. i dont need it to be SuperCID, nor i need to flash any other ROM. and unfortunately, imei-check cannot do this (there are NO options for a SIM unlock-only, or a SIM unlock and SuperCID)...
i hope any of the gurus here can help, or at least confirm this understanding...
old X01HT can perfectly unlocked by V3.
how do you know the date about your X01HT produced?
lyerx said:
old X01HT can perfectly unlocked by V3.
how do you know the date about your X01HT produced?
Click to expand...
Click to collapse
well, if you look at the System Info tag in Settings you'll see a date... mine is at:
>ROM: 1.33.761.4
>ROM Date: 11/10/06
>Radio Version: 1.14.00.10
Just for clarification:
imei-check temporarily SuperCIDs your device, you lost the SuperCID status when you flash another radio on it.
With the 1.16 patched radio included in my unlocker you also temporarily SuperCID the device, then you have to run the exe file on your Hermes which will let you choose if you just want to SIM-Unlock or both (do the SuperCID sticky forever). If you don't choose the SuperCID option, then the SuperCID status is lost when you flash another radio on it.
I have had reports of people unlocking without problems X01ht devices with v3, but some others reported they can't boot OS after unlocking, and as I can't test it I put the warning, so do it at your own risk.
Anyway, I'm planning to release a new unlocker version soon
pof said:
Just for clarification:
imei-check temporarily SuperCIDs your device, you lost the SuperCID status when you flash another radio on it.
With the 1.16 patched radio included in my unlocker you also temporarily SuperCID the device, then you have to run the exe file on your Hermes which will let you choose if you just want to SIM-Unlock or both (do the SuperCID sticky forever). If you don't choose the SuperCID option, then the SuperCID status is lost when you flash another radio on it.
I have had reports of people unlocking without problems X01ht devices with v3, but some others reported they can't boot OS after unlocking, and as I can't test it I put the warning, so do it at your own risk.
Click to expand...
Click to collapse
thanks for the reply, pof...
on the other hand, what do you mean by "temporarily SuperCIDs..."...? would it mean that the device is still registered to Softbank and at the same time you can flash another ROM?
all i want though is just have my device SIM-free so i dont have to deal with exorhbitant roaming rates when travelling abroad... not much privy with playing with other ROMs, yet; as well as not wanting to void my warranty.
Anyway, I'm planning to release a new unlocker version soon
Click to expand...
Click to collapse
really? what would be the new stuff that youd be adding in?
I am an owner of a BEFORE DEC. model X01HT and sim unlock&SuperCID by pof's v2a unlocker.
Since April is coming, I have to update the rom to use the net according SB. I wonder if the sim-unlock will remain after I update. i hope so sadly.
I, TOO, don't mind the SuperCID.
Anyway, thank pof ad waiting for the new unlocker.
ps: if i use another sim card other than SB, I can use WIFI or BT only about two minites continiously. then it will be disconnected automatically. Anyone else has same experience? I use SB_USIM to avoid the annoying popup.
I submit this post via my X01HT.
Yeas, Ive read the thread...
http://forum.xda-developers.com/showthread.php?t=293665
Click to expand...
Click to collapse
Does the info need updating, or do I need to do something different...
v3a [03-04-2007] - New RUU will make sure HardSPL-1.40 is installed before flashing the radio
Now the unlocking process is faster & safer
Click to expand...
Click to collapse
I have SPL-2.10 on my phone, not 1.40 as stated above....
v2 [12-11-2006] - updated to patched radio 1.16
Click to expand...
Click to collapse
Q: After finishing the process it still asks for unlock code, what should I do?
A: Make sure you have radio version 1.16 and run Herm_Unlock_v3.exe on your phone and select unlock option. If entering any unlock code fails, please repeat the unlocking process again (you did something wrong the first time).
Click to expand...
Click to collapse
My Radio is 1.38.00.01.. will using this downgrade it to 1.16??, or do I need to pu 1.16 on before using this tool...??
Ot, once it is unlocked, can I simply stick a new radio on it???
Do I alsoneed to have the working orange sim in their.. as if I put the t-mobile sim in, it is just asking for the simlock code...
As ther eis always a chance of bricking your phone, I just want to be sure everything is ok, before I do it..!! I have the offical wm6 rom installed.
Thanks
Anyone...???
So no one has used this to unlock a phone that has HardSPL-2.10, or a later Radio....??? or reflashed their phone after unlocking...???
Once unlocked, does it remain unlocked for good???
PATIENCE....let us answer when we can!!
Your SPL will end up being downgraded to 1.40.olipro......but thats not a problem as you can just flash HardSPL 2.10.olipro again.
Your Radio WILL be downgraded to 1.16 as this is a hacked radio image which allows the SIM/CID to be unlocked.
You really should update the radio once the device is unlocked since there are BIG improvments with the new ones.
ANY SIM card will work in the device once the device is unlocked....the sim pin pad pops up when the SIM card requires the sim pin code. Obviously if you know the pin you can turn this off in phone settings.
Soory for my impatience.. Ive been biting at the bit all day, after my contract ended and waiting over 2 weeks to sort a new deal out... I was so eager to get my handset up and running...!!!
Thanks for your information... I was unsure whether you could simply re-apply the radio and spl after the unlock....
Maybe this info could be added to the sticky.. after reading through the 50 odd pages, there were many such requests, with no answers....
So as I understand, downlograding to the hacked radio simply facilitates the unlocking, rather than providing the unlock, so flashing back up after, and replacing the hacked radio with a genuine one does not reverse the unlock...
Seriously though, this could do with being on the appropriate thread about SIM/Cid unlocking....!!
Discovering this site about a month ago, and what developers and contributors have done has breathed new life into what was already a great little device...
THANK YOU!!
The seller said it is unlocked. How can I verify it?
I read CID Unlocking and Sim Unlocking. How can I confirm both.
Also, how can I tell which version of the radio?
and which version of SPL (3.5 or 1.2)?
Or is there any great tutorial I can setup for the AP4?
I am starting to get confused.
the seller probably was not lying as it is easy to do (thanks to olipro - cmonex/olinex) but if you want to check, press and hold your camera button, whilst doing that press the reset button, and tell us the details on the rainbow screen.
this will also tell you if it is SPL 1.1-1.2 or 3.5
when your done just press reset again
LOCKing is related to SPL. SPL is a part of the "bios" (just to use the PC paradign IPL and SPL are "extended bios" ), then you have the RADIO section of the rom and the OS (WMxx)
Other part of the rom are the EXTENDED ROM (where the file needed for operator customizzation during first install are stored) and splash screens (a FULL ROM means IPL,SPL, SPLASH 1, SPLASH 2, RADIO, OS, EXTENDED ROM).
This "bios" , called SPL can receive commands from RUU (Rom Update Utility, the sw used to flash the rom file). ROM info are "wrapped" in a .nbf file and the RUU, interacting with SPL with some batch commands, flash into the device memory the ROM parts (Splash are flashed in their locations, os, radio, ....) RUU opens the .nbf file, read abatch command file, and send the commands to the SPL to flash the rom sections
Now you can understand how a custom ROM is done: using a "kicken" you can prepare a .nbf file containing the data and the batch command file used by RUU to flash it in the right location of your ROM (SPL, RADIO, OS, SPLASH, or all together) SPL is a KEY part for this process.
With the stock RUU IPL and SPL some controls are done before flashing, first of all device's language and vendor ID, so called CID. If they doesn't mach with the ROM file you will have an error and RUU exits: wrong language, wrong vendor, ....
Flashing a custom SPL you avoid this check (or it sets the CID to "supercid", it means I accept every language and vendor ID)
The SIM unlock (phone working with all SIM card) needs something more complex. In the ATHENA FORUM whe have ATHENA UNLOCKER, from OLIPRO, for SIM Unlock and CID Unlock and ATHENA WRAPPER, just for CID unlock. They will update the HTC SPL to OLIPRO 1.2
Hi sergiopi,
Your post is so concise. You told us the whole theory it may take me more than a day to find. You have the potential to be a book author. Thanks anyway.
Questions:
1. How can I tell whether the sim is unlocked?
2. How can I tell whether the cid is unlocked? Or it is no harm to run the ATHENA UNLOCKER again?
3. What is the different btw SPL 3.5 and 1.2? Should I update it? I am planning to run the AP4.
Thanks again!
Did you completely miss my previous post, if you follow the simple instructions. I gave you earlier, we will be able to answer all your questions.
ice_coffee said:
Did you completely miss my previous post, if you follow the simple instructions. I gave you earlier, we will be able to answer all your questions.
Click to expand...
Click to collapse
To check if your Athena is SIM Unlocked take a SIM from your friend's phone who is in another network and put it in your Athena. If it refuses to accept the SIM then it is locked and you have to unlock it. If it accepts the SIM and lets you place a call, it is SIM unlocked and most probably CID Unlocked. To check if it is CID unlocked just do what ice_coffe says.
I didn't miss the post from ice_coffee. My Athena is still in shipping. I just want to get more info first. Besides testing with a real sim card, is there any method we can run from the machine?
alui said:
Hi sergiopi,
Your post is so concise. You told us the whole theory it may take me more than a day to find. You have the potential to be a book author. Thanks anyway.
Questions:
1. How can I tell whether the sim is unlocked?
2. How can I tell whether the cid is unlocked? Or it is no harm to run the ATHENA UNLOCKER again?
3. What is the different btw SPL 3.5 and 1.2? Should I update it? I am planning to run the AP4.
Thanks again!
Click to expand...
Click to collapse
Thanks, the post is for you and for other newbies, to help everyone to understand. This is a DEVELOPER'S forum, we like smart users!
alui said:
Hi sergiopi,
Your post is so concise. You told us the whole theory it may take me more than a day to find. You have the potential to be a book author. Thanks anyway.
Questions:
1. How can I tell whether the sim is unlocked?
2. How can I tell whether the cid is unlocked? Or it is no harm to run the ATHENA UNLOCKER again?
3. What is the different btw SPL 3.5 and 1.2? Should I update it? I am planning to run the AP4.
Thanks again!
Click to expand...
Click to collapse
Listen Alui. The question numbr 3 shows of your post shows that you are realy a noobie. So if you are still waiting for your new device, do not waste your time but start reading. If you already decided that you want to go for AP4, then did you realy read the AP4 thread from first post? I am almost sure, you didn't.
So please remember, if you do not know what you are doing then you have a big chance to convert your super device into a brick.
And once more, if you browse this forum, you can see how many threads is there, and how many post is in each thread. If you see this you should be sure that you are not the first person here who just got his new device. All your questions were answered many times here so just read and read and after a week of reading start to plan what to do next.
Hello,
I have tried absolutely everything I know and that I have read. 3 different micro sd cards and 2 card readers. I actually bought a Kingston card and kingston card reader because I read kingston works fine for goldcard. I am desperate for fixing this.
There is no way I can get passed the loading screen after rebooting the phone in usb host mode. This are the steps I follow.
My phone at&t Titan pi39100
1. Create goldcard using a 2gb kingston.
1.1 Format the card in Fat32
1.2 Apply the goldcard tool
1.3 Copy the eterimg.nhb file that comes in the file provided by Cotulla for the SPL. (25 mb) ( I have actually tried inverting the order of steps 1.2 and 1.3 just for the sake of trying)
2. Prepare the Y cable as you can see in the pictures attached and reboot the phone and try to flash the SPL. Pressing power, vol - and camera. It gets in to the usb host mode and then a loading screen appears for a few seconds. Next thing I see is the spl screen reading
PI39100 MFG
SPL-2.5 160015.3 (137079)
eMMC SND 15188MB
TOUCH A1 (F:81, ID:1, V11, B:F8)
RADIO- 16.23.02.26_A
Now, I have noticed that if after this I try to flash the hspl I get the congratulations message, but my phone has not changed at all and I cannot flash any custom rom.
I read somewhere that the MFG may be a type of SPL that is impossible to flash, Can someone please confirm that I am not missing any step that that there is just no hope for my phone?
I have spent hours and hours reading and trying with this. I had the hope that some of the problems I have with the phone will be fixed with a Custom Rom, but if I can't flash it, I think I'm getting rid of the phone. I see lots of potential with the windows phone but my personal experience has been terrible
If someone can help I would be totally thankful.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
andres22 said:
Hello,
I have tried absolutely everything I know and that I have read. 3 different micro sd cards and 2 card readers. I actually bought a Kingston card and kingston card reader because I read kingston works fine for goldcard. I am desperate for fixing this.
There is no way I can get passed the loading screen after rebooting the phone in usb host mode. This are the steps I follow.
My phone at&t Titan pi39100
1. Create goldcard using a 2gb kingston.
1.1 Format the card in Fat32
1.2 Apply the goldcard tool
1.3 Copy the eterimg.nhb file that comes in the file provided by Cotulla for the SPL. (25 mb) ( I have actually tried inverting the order of steps 1.2 and 1.3 just for the sake of trying)
2. Prepare the Y cable as you can see in the pictures attached and reboot the phone and try to flash the SPL. Pressing power, vol - and camera. It gets in to the usb host mode and then a loading screen appears for a few seconds. Next thing I see is the spl screen reading
PI39100 MFG
SPL-2.5 160015.3 (137079)
eMMC SND 15188MB
TOUCH A1 (F:81, ID:1, V11, B:F8)
RADIO- 16.23.02.26_A
Now, I have noticed that if after this I try to flash the hspl I get the congratulations message, but my phone has not changed at all and I cannot flash any custom rom.
I read somewhere that the MFG may be a type of SPL that is impossible to flash, Can someone please confirm that I am not missing any step that that there is just no hope for my phone?
I have spent hours and hours reading and trying with this. I had the hope that some of the problems I have with the phone will be fixed with a Custom Rom, but if I can't flash it, I think I'm getting rid of the phone. I see lots of potential with the windows phone but my personal experience has been terrible
If someone can help I would be totally thankful.
Click to expand...
Click to collapse
the AT&T Branded HTC Titan is not compatible with DFT's HSPL at the moment. Any attempt will update your SPL from 1.10 to 2.5 which is locked to the phone. Only Rom that is flashable is the Stock AT&T image.
Last we heard from Cotulla among other HTC Titan users are testing possible issues/solution. So for the time being there is no ETA as usual and we AT&T Titan owners are stock with what we currently have.
So the best you can do is flash the stock rom and update to 8107 and patiently wait for any news from DFT/Cotulla
Hey yo...is this an ATT Titan? or an unbranded Titan? It looks like an ATT Titan...but anyway, if it is an ATT Titan, did you successfully debrand the device to the Euro Rom first?
I see Tachi has beaten me to the punch...
Yes...I think we need to tell Cotulla or DFT to put a warning to ATT users who want to try this on the direction page.
IT IS AN ABSOLUTE MUST FOR AT&T TITANS THAT IN ORDER TO INSTALL THE DFT SPL/HSPL - YOU MUST FIRST DEBRAND YOUR DEVICE TO A EURO ROM! - lol -- However, I hear that soon ATT users will be getting some updates along with the 2.5 SPL...so this may be only temporary.
Try to flash back to the original ATT rom and see if the SPL will return back to 1.10. If it doesn't...be patient...they are working on a fix for this.
the AT&T Branded HTC Titan is not compatible with DFT's HSPL at the moment. Any attempt will update your SPL from 1.10 to 2.5 which is locked to the phone. Only Rom that is flashable is the Stock AT&T image.
Last we heard from Cotulla among other HTC Titan users are testing possible issues/solution. So for the time being there is no ETA as usual and we AT&T Titan owners are stock with what we currently have.
So the best you can do is flash the stock rom and update to 8107 and patiently wait for any news from DFT/Cotulla
Click to expand...
Click to collapse
Hi Tachi91, Yes I updated to 8107. I guess it is all I can do for now. Thanks for your answer!
Hey yo...is this an ATT Titan? or an unbranded Titan? It looks like an ATT Titan...but anyway, if it is an ATT Titan, did you successfully debrand the device to the Euro Rom first?
I see Tachi has beaten me to the punch...
Yes...I think we need to tell Cotulla or DFT to put a warning to ATT users who want to try this on the direction page.
IT IS AN ABSOLUTE MUST FOR AT&T TITANS THAT IN ORDER TO INSTALL THE DFT SPL/HSPL - YOU MUST FIRST DEBRAND YOUR DEVICE TO A EURO ROM! - lol -- However, I hear that soon ATT users will be getting some updates along with the 2.5 SPL...so this may be only temporary.
Try to flash back to the original ATT rom and see if the SPL will return back to 1.10. If it doesn't...be patient...they are working on a fix for this.
Today 09:02 PM
Click to expand...
Click to collapse
I cant go back to 1.10 I am stuck at 2.5 no matter what I do. I tried to debrand to a Euro Rom with no success either, this is actually what had me confused cause I could read some post from AT&T users confirming that they had flashed the DFT HSPL.
Well I will keep waiting. I agree with you that a warning for AT&T usera at the beginning of the post would be helpful.
Thanks a lot to both of you. At least I can sleep tonight knowing I it's not that I am missing some evident step.
AT&T sucks their policy is an abuse of power (to the eyes of a European) There are lots of things I miss from the US and I am looking forward to go back, but my phone carrier is not one of them
P.S. I can't make backups of the phone with Zune either, it give me an error and neither the patch from htc or the solution from microsoft work. Just sharing it in case it helps someone.
xconomicron said:
Hey yo...is this an ATT Titan? or an unbranded Titan? It looks like an ATT Titan...but anyway, if it is an ATT Titan, did you successfully debrand the device to the Euro Rom first?
I see Tachi has beaten me to the punch...
Yes...I think we need to tell Cotulla or DFT to put a warning to ATT users who want to try this on the direction page.
IT IS AN ABSOLUTE MUST FOR AT&T TITANS THAT IN ORDER TO INSTALL THE DFT SPL/HSPL - YOU MUST FIRST DEBRAND YOUR DEVICE TO A EURO ROM! - lol -- However, I hear that soon ATT users will be getting some updates along with the 2.5 SPL...so this may be only temporary.
Try to flash back to the original ATT rom and see if the SPL will return back to 1.10. If it doesn't...be patient...they are working on a fix for this.
Click to expand...
Click to collapse
I have Bootloader version: 1.10. What does this mean? I can debrand my at&t titan without goldcard method?
Strangely, I also have internet sharing on my AT&T titan.
zup2sky said:
I have Bootloader version: 1.10. What does this mean? I can debrand my at&t titan without goldcard method?
Thanks
Click to expand...
Click to collapse
NO!
Flash the European ROM so that your titan can be debranded. If you attempt to DFT unlock now you will be stuck like the rest of us
Tachi91 said:
NO!
Flash the European ROM so that your titan can be debranded. If you attempt to DFT unlock now you will be stuck like the rest of us
Click to expand...
Click to collapse
Somewhere in the forum, you must use GOLDCARD method to debrand- does this applies to me as well? I bought the AT&T Titan used- the previous owner somehow has internet-sharing option under the settings.
zup2sky said:
Somewhere in the forum, you must use GOLDCARD method to debrand- does this applies to me as well? I bought the AT&T Titan used- the previous owner somehow has internet-sharing option under the settings.
Click to expand...
Click to collapse
Yes you need a goldcard to debrand the titan. To get internet sharing under settings the previous owner must have updated to 8107 since thats how i got that under settings as well. So you can check under "About" and if you have anything other then 7720 under "OS Version" that means they used the cabsender.
Tachi91 said:
Yes you need a goldcard to debrand the titan. To get internet sharing under settings the previous owner must have updated to 8107 since thats how i got that under settings as well. So you can check under "About" and if you have anything other then 7720 under "OS Version" that means they used the cabsender.
Click to expand...
Click to collapse
I have 7.10.7720.68 - So by your logic, he did not use 'cabsender.'
I wonder how he got internet sharing there- can this phone be possibly unlocked?
zup2sky said:
I have 7.10.7720.68 - So by your logic, he did not use 'cabsender.'
I wonder how he got internet sharing there- can this phone be possibly unlocked?
Click to expand...
Click to collapse
If by unlock you mean full on Interop DFT unlock then yes if you have SPL 1.10
Those who have had success using DFT unlock had previously used a Goldcard to flash a European ROM. The issue we are having is that if you attemp to flash DFT unlock with SPL 1.10 to get stuck.
So if you want custom roms it will be smart to first flash a European ROM (2.05) using the goldcard. Once you are runnig the unbranded 8107 rom then start the DFT unlock process
No problem andres22,
haha, And yes, I would agree...as would most-all AT&T users too.
zup2sky said:
Somewhere in the forum, you must use GOLDCARD method to debrand- does this applies to me as well? I bought the AT&T Titan used- the previous owner somehow has internet-sharing option under the settings.
Click to expand...
Click to collapse
All the AT&T Titan I believe, had the Internet Sharing in the stock Rom. I got 2 Titan last November with 7720 ROM with it.
Just want to let everyone in this thread know;
I see claims that debranding must be done and guarantees success...
There has been no quantitative proof that debranding does anything. The success stories are the loudest, of course, and more and more threads keep popping up where users are saying "if only I debranded I wouldn't be stuck on SPL 2.05!"
Having met with success after debranding doesn't prove anything. I didn't debrand and I got my Titan to HSPL, admittedly it was a lengthy and unnerving process. I don't think that debranding does anything, I don't think it even logically CAN do anything, but what I do know is that the AT&T titan is not "not supported", as was claimed in one of the first posts. It was supported, but I'd say half (or less than half, again, loudest of the bunch) of users are having issues with at least two parts of the process, and DFT is looking into it.
I guess I should get off my ass and see if I can unstick the SPL on my second titan.
link68759 said:
Just want to let everyone in this thread know;
I see claims that debranding must be done and guarantees success...
There has been no quantitative proof that debranding does anything. The success stories are the loudest, of course, and more and more threads keep popping up where users are saying "if only I debranded I wouldn't be stuck on SPL 2.05!"
Having met with success after debranding doesn't prove anything. I didn't debrand and I got my Titan to HSPL, admittedly it was a lengthy and unnerving process. I don't think that debranding does anything, I don't think it even logically CAN do anything, but what I do know is that the AT&T titan is not "not supported", as was claimed in one of the first posts. It was supported, but I'd say half (or less than half, again, loudest of the bunch) of users are having issues with at least two parts of the process, and DFT is looking into it.
I guess I should get off my ass and see if I can unstick the SPL on my second titan.
Click to expand...
Click to collapse
If your claim is true- this changes everything.
Care to elaborate how you obtained HSPL on your titan? I am sure at&t titan owners are eager to know
Well I have two AT&T Titans, because I thought I half bricked my first one with the f400 error. Then I f400'd the second Titan.
I went back to work on my original Titan, I got rid of the f400 error and I THINK I was stuck on SPL 2.05, HSPL wouldn't install even though it said success. Some combination of hard resetting and flashing the stock ROM brought me back to SPL 2.10, from there I flashed 2.05 again and then HSPL worked.
I have spent significantly less time trying to HSPL my second Titan, but for what it's worth I have been unable to duplicate whatever I did to my first Titan in my half hour of tinkering with it. Stuck on 2.05.
(I think I spent no less than 20 hours on my first Titan, though most of that was because goldcard wasn't working with all but one of my USB devices.
Stuck at spl screen with 2.05 spl
link68759 said:
well i have two at&t titans, because i thought i half bricked my first one with the f400 error. Then i f400'd the second titan.
I went back to work on my original titan, i got rid of the f400 error and i think i was stuck on spl 2.05, hspl wouldn't install even though it said success. Some combination of hard resetting and flashing the stock rom brought me back to spl 2.10, from there i flashed 2.05 again and then hspl worked.
I have spent significantly less time trying to hspl my second titan, but for what it's worth i have been unable to duplicate whatever i did to my first titan in my half hour of tinkering with it. Stuck on 2.05.
(i think i spent no less than 20 hours on my first titan, though most of that was because goldcard wasn't working with all but one of my usb devices.
Click to expand...
Click to collapse
can you give the link for the stock rom with spl 2.10 and did you boot the phone successfully after flashing this stock rom???? Please help i am stuck on the spl screen indefinitely and nothing is working to get my phone back to working condition...