PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
Related
i have tried install chiense wm5 3.5.2 akuu and now my boot loader dont workin first says usb error and i tried try instal new one boot loader with memory stick but now bootloader totaly crashed no workin no cant see colores screen
i have tried found in forum but a lot topic
and sorry for low english
1. take out yr battery from yr atom for about 1 minute
2. press the camera button and the reset
3. load the AKU 3.3.3 or the original O2 atom software
Violalie.. and waiting for 20 to 30 minutes as it will flash.. Good Luck mate.
dude thx for info but it didint work i did take out battery sim card and memory card 12 hour still cant enter boot load only a black screen comin and goin
Try the following:
For those of you who have downloaded and flashed using SD Card method who ended up in a brick! ITEX recovers his Atom by following procedure:
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode.
Taken from http://forum.xda-developers.com/showthread.php?t=314613
ehm didint work what should i do
can i change bios my atom
Your bootloader was destroyed and you can only send your device to service.
1) your devices can boot up and use well?
2) did you mean that even if you try to hard reset your devices, it wont goes to boot loader mode?
3) PC cannot detect your hardware when you goes to boot loader mode / WM5 mode?
Did u try copying aku 3.3.3 image file in memory card and try boot loading?..
no i didnt try because my boat loader no workin cam+reset and volume+rec+reset dont working i cant load anything
Remove Battery
press power + Joystick + Reset(Stylus) then place the battery ??..
Normally i press Power+Joystic+Reset(Stylus) to go into bootloader.
If you closely read AKU 3.3.3 thread.. there is one place you can see methods to bootup Bricked ATOM.. try page 78 onwards??
Thanks.
Remove Battery
press power + Joystick + Reset(Stylus) then place the battery ??..
Normally i press Power+Joystic+Reset(Stylus) to go into bootloader.
If you closely read AKU 3.3.3 thread.. there is one place you can see methods to bootup Bricked ATOM.. try page 78 onwards??
Thanks
Click to expand...
Click to collapse
dude its only resetting phone taking factoty settings no i didint i am readin now
when i remove battery and wait a while and put it back orange led ligthing one time its mean my brick not fail totaly ?
vhd99 said:
when i remove battery and wait a while and put it back orange led ligthing one time its mean my brick not fail totaly ?
Click to expand...
Click to collapse
Your atom is still live.. check out below thread .. how they recover a dead atom..
http://forum.xda-developers.com/showthread.php?t=314613&page=76
http://forum.xda-developers.com/showthread.php?t=314613&page=77
http://forum.xda-developers.com/showthread.php?t=314613&page=78
what mean hard reset
ok i got what hard reset i did hard reset but still no goin boot loadin i tried all methods
It's NOT hard Reset.
1) Remove the battery for at least 1 min.
2) Take back the battery in
3) Press the Camera Button following with the pin hole(reset button)
i erased boot by misyake any body help me how to restor boot device now fully dead
just orange led when i plug usb
You should search the forums first, however, this might help http://forum.xda-developers.com/showthread.php?t=331818&page=2
thx mate for replay
but not help coz device totaly dead anad dont enter boot loader
abcrino50
Use JTAG cable and JFLASHMM software to restore bootloader.
And learn russian Boys from 4pda.ru already restored their bootloaders.
PLEASE LEARN TO READ THE WIKI PAGE...after reading this , last resort is the forum
http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK
Your device is bricked, if and only if, your device won't start normally... even if you press soft-reset, hard-reset, or even bootloader mode buttons. Usually a brick is caused by improper ROM upgrade, and using tools that modify the ROM. Before panicking, do the following:
Brick Test:
1. Make sure your device has ample battery charge. If you're not sure plug it in with the wall charger for at least 10min
2. Remove your battery for at least 1 minute
3. Replace your battery while observing the LED lights
4. If the LED blinks once upon battery insertion, you might have hope yet
The only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding the buttons
4. Release the buttons at the same time (You should see bootloader screen)
Note: Failure to hold the buttons at the same time during battery insertion will cause it not to work.
----------------------------------------------
If nothing HAPPENED after this trial of revival, your atom MAYBE BRICKED/forever dead.
If there is no LED LIGHT on ur atom, YOUR ATOM IS BRICKED.
sorry my friend, your phone is a paperweight NOW if this is the situation.
LAST RESORT: O2 service center, ur lucky if they have support in ur country. but the price for fixing (if not under warranty)...mmmm a new iphone ;-)
abcrino50 said:
i erased boot by misyake any body help me how to restor boot device now fully dead
just orange led when i plug usb
Click to expand...
Click to collapse
abcrino50
Please read
http://forum.xda-developers.com/showthread.php?t=336278
and waiting 1-3 days
when i power on my atom,
it only flash the orange led and never work anymore,
even if i reset or push the power button,
it happens nothing.
the only way make me think it's not a brick is to replace the battery,,
keep holding reset and center button then put the battery on and off many times,
then i put the battery on and release all buttons,
it goes into the bootloader,
then i connect atom with usb cable,
my computer shows unknown device.
johnjohn1977 said:
when i power on my atom,
it only flash the orange led and never work anymore,
even if i reset or push the power button,
it happens nothing.
the only way make me think it's not a brick is to replace the battery,,
keep holding reset and center button then put the battery on and off many times,
then i put the battery on and release all buttons,
it goes into the bootloader,
then i connect atom with usb cable,
my computer shows unknown device.
Click to expand...
Click to collapse
read the wiki...
Did you Flash a new ROM?
Regards,
Carty..
Carty said:
Did you Flash a new ROM?
Regards,
Carty..
Click to expand...
Click to collapse
yes
i flash a wm6 rom without reading the attention carefully
use spritebackup
Hi there,
If you plug the carger in and the red light shows, then it's charging. If this is the case you may be able to put it into bootloader and try again, but with proper rom.
hope this helps
2234jones said:
Hi there,
If you plug the carger in and the red light shows, then it's charging. If this is the case you may be able to put it into bootloader and try again, but with proper rom.
hope this helps
Click to expand...
Click to collapse
i can't flash my device with any rom
the bootloader seems have some problem
i can't use camera+reset to change into bootloader mode
johnjohn1977 said:
i can't flash my device with any rom
the bootloader seems have some problem
i can't use camera+reset to change into bootloader mode
Click to expand...
Click to collapse
remove your battery about 1-2 minutes and plug in back, after that try to press camera + reset.
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Qiky said:
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Click to expand...
Click to collapse
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
just want to add dolphin post
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
knoxbrotherhood said:
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck