Hi everyone,
I need some help with pairing the bluetooth with my Touch2.
Followed the instructions for the headphones, everything happens as it should (red and blue light flashes alternately on the headset), but the phone won't see the headset.
Later I saw on the headset box that bluetooth version is "V2.0 + EDR", on the other hand on my Touch2 box b'tooth version is "2.1 + EDR and A2DP".
Is the difference between b'tooth versions the reason that they don't pair, or something else causes the problem?
Long Press the power button of blutooth headset,then search headset in the Touch2.
Good luck!
I'm sorry for my English!
Nicholaszeng said:
Long Press the power button of blutooth headset,then search headset in the Touch2.
Good luck!
I'm sorry for my English!
Click to expand...
Click to collapse
I managed to pair, but first i had to replace the bluetooth headset because it wasn't working properly. I was lucky my friend had the same b'tooth headset, we tried with his and it was a success. It was a bit hard to convince the guy in the store that headset wasn't working properly before i bought it, so everyone: TEST YOUR ACCESSORIES IF YOU CAN IN THE STORE THE VERY MOMENT YOU BUY IT.
Thanks for the answer anyway
Related
Hi there! I have an MDA II and a Parrot CK-3000 (with sw ver. 3.13) carkit. I read about the outcoming of this sw and I decided to install it on my MDAII. But, after a correct installing procedure, it simply doesn't work: my carkit remains mute like a fish!!! :shock: I'm asking you, guys already use successfully this sw, a hand of help to solve my trouble (if possible). Note that I downloaded it from this
http://bluetooth.i-networx.de/index_e.html
and I tried to follow all the instructions placed in there...
Thank you all!
pap
paperuccio said:
Hi there! I have an MDA II and a Parrot CK-3000 (with sw ver. 3.13) carkit. I read about the outcoming of this sw and I decided to install it on my MDAII. But, after a correct installing procedure, it simply doesn't work: my carkit remains mute like a fish!!! :shock: I'm asking you, guys already use successfully this sw, a hand of help to solve my trouble (if possible). Note that I downloaded it from this
http://bluetooth.i-networx.de/index_e.html
and I tried to follow all the instructions placed in there...
Thank you all!
pap
Click to expand...
Click to collapse
Why not email the author, he is most helpful.
Had the same issue with the Parrot. My Plantronics headset works a treat, but not the Parrot.
I mailed the author who confirmed there are some problems and a new release will be needed.
As the author is doing this work unpaid and the functionality is so good, I can wait.
@ mrg2003
I send an e-mail some days ago but still had no response.
Anyway, I agree with IanF and I'll wait for the new release.
I wish I read this bulletin board more often.
Yes, I have exactly the same problem with the CK3000 (v3.13) and PBT. HBH-35 works a treat but CK3000 does not bond (XDA thinks it does but there is no handshaking and CK3000 repeats request to bond).
Back to basics again ...
Incidentally, does anyone know if Tobias plans to engineer a way to trigger Voice Command and take input from the car microphone for voice recognition? Would be the dogs and well worth a major donation ....
Cheers
I've had some problems with pocket bluetooth. I have emailed tobias as follows and am awaiting a reply. Was wondering if anyone has faced similar problems:
Tobias,
Thanks for all the hard work in getting these tools working. I have just bought an XDAII with the latest 1.60.00 ROM using the 1.10.00 radio version.
At the same time, I have a WIDCOMM bluetooth dongle on my PC which supports numerous profiles including the headset profile, which allows me to use the PC's speakers and mic as a 'headset' with the XDAII.
I set up the XDAII with the PC, using the built-in bluetooth bonding and pairing application and managed to get it all working fine with the PC using the speakers and the mic as the headset, with the phone automatically transferring the call to the PC when the 'Bluetooth Headset mode is enabled' shows on the today screen. Furthermore, activesync also seems to work fine too.
After installing Pocket Bluetooth Tools, the headset stops working. Before installing it, I unpaired the device by deleting it from the list of paired devices. After installation and going through the process of pairing the device again, it correctly gives me the option to choose the Serial Port, ActiveSync, Modem, and Headset profile. I select all of these and click on OK. Once this happens, my PC gives me a message saying that the XDAII has connected with the headset. However, this doesn’t happen once but goes into a continuous loop giving me notifications every 2-3 seconds that this is the case. Furthermore, when making a call to see if the voice has been transferred to the PC< this stops working and the XDAII's speaker and mic continue to be used. The only way to stop the constant loop of connections is to switch off the bluetooth radio on the XDAII. Furthermore, when deleting the pairing from the XDAII this constant loop continues.
Have you faced this issue previously, as I think it may be a bug. The only reason I installed pocket Bluetooth is that my current b.tooth headset is a Nokia HDW-30 that supports the handsfree profile and your documentation states that Pocket Bluetooth tools supports this profile.
Let me know if there is a fix for this.
pap[/quote]
Why not email the author, he is most helpful.[/quote]
maybe just because he doesn't answer
i wrote a very long report some days after the long awaited new version came out in april, but haven't got any reply. (maybe my email got lost - who knows ...)
i have exactly the same problems. i also have a parrot ck3000 (tried with firmware 3.11 and 3.13) and an mda2 with rom 1.6.00GER and extROM 1.60.07. the two devices pair, and sometime i can even select the "headphone profile" afterwards. i even managed to make it work ONCE, after several hours, of installing, reinstalling, pairing, reparing, ect, ect ...
what did work once was making calls. but after the first call came in, i could answer it, the caller could hear me, but i couldn't hear anything. this happened twice and then i just turned off bt and used the mobile as always.
as i'm using my mda in my car for work and not for fun this is no solution for me . i went back to the original bt stack that works quite well. i can make and take calls w/o any problems.
one thing i'd like to see changed (as soon as parrot and mda work together) is, that ALL calls are made via the handsfree, as, as long i'm in the car it HAVE TO use the handsfree by law (and it's much more comfortable anyway). it's not practicle to dial with the mobile, and then by pressing the green button on the parrot to move the call to the handsfree. but that's the only way you can do it when using speeddial.
another thing i desperately miss is a way to change the volume of the handsfree. i could do this using the volume slider of my nokia 6310, but volume stays all the same when using the mda. and it's just too low when doing higher speeds on the autobahn
of course voice dialing would be a great feature to have ... but it's not that necessary.
please don't get me wrong .. i'm don't want to be ungrateful as i'm not paying for this software - i just want to help ppl by saying that they are not alone with their problem and they should give up wasting their time and better wait for a new release....
and of course i'm very willing to PAY for that software as well as soon as it is any improvement over the original bt stack (for me of course. for most of you it already is)
maybe TOWA could say some words here. that would be really appreciated.
thanks anyway a lot to all ppl that spend their free time developing software and providing it to the comunity!!! thumbs up !
regards ize|man
Bluetooth tools and ROM 1.72
Does ROM version 1.72 require TOWA's bluetooth tools? In this ROM, there are options for COM port selection etc under Bluetooth settings and the clubimate site mentions bluetooth improvements. Anyone with this info?
other com settings then
Inbound COM port com4
outbound COM port com5
??
if so what are they?
Rudegar
You are right. Inbound 4, outbound 5. Likely required for GPS devices, if i am not mistaken
faisal said:
Rudegar
You are right. Inbound 4, outbound 5. Likely required for GPS devices, if i am not mistaken
Click to expand...
Click to collapse
These are the ports for BT beaming, as I understand! (not for BT GPS).
For BT GPS you do not specifically need BTHTools anymore (since 1.66) because WM can install a BT GPS com at first bonding.
Something is different however (vs BTHTools) since with 1 application (Alturion) I can not get the BT GPS working anymore, which can also not be solved by still installing BTHTools!! (while I have no problems with my other application TT. Figure that out?!)
Ronald
I now have the same problem, the parrot ck3000 was working until I insatlle dthe bluetooth tools, and now it doesn't.
Its a shame I did not see this thread before
Will the 1.72 rom work with both parrot and my emtac bluetooth gps?
Cheers
Justinp
justinp
have you tried uninstalling Bluetoothtools?
no not yet, I might give that a go, but then my gps wont work :?
justinp said:
no not yet, I might give that a go, but then my gps wont work :?
Click to expand...
Click to collapse
I think it will still work!
With my working application (TT3) I see the GPS on COM5 (installed by WM) + on COM7 (installed by BTHTools) + on the BT/SIRF interface!
If I uninstall BTHTools I only loose the selection for COM7. The other two selections still work!
Of course you must have acknowledged the WM com installation with first bonding (in any case for the serial operation)! My BT/SIRF connection always works in TT3 regardless of WM/BTHTools installation of serial ports.
Ronald
I'm also having that strange problem with the parrot CK3000. I did install the previous version of BT but I don't see any difference with or without BT. But when I de-install and want to go back to the original state, the same problem persist. Is there any way to download anyware the original Bluetooth stack without re-install everything (and loosing all my settings and software)?
Thanks for helping out.
Frank.
Sorry if it has been answered before, but I tried searching and it came up with about 1500 responses... :roll:
I used the Broadcomm BT stack but it doesn't support the headset profile. So I removed them, but during the removal process my 2020 hard reseted... Any way I got up and working with a fresh backup with the standard MS BT Stack, but now the Bluetooth Headset Plugin in the Today Screen, the one used to set on or off the Headset option has dissapeared. Now I paired my BT headset but have no way to start the BT Handsfree profile since I miss the BT Plugin... Any way to find it back?
Thanx and sorry for the mess...
Thanx for your... help. Solved the problem.
welcome
Hi!
I've got a Jabra BT3030 headset which works great with the phone and media player in my opinion. It's just that I have problems connecting.
First connection went fine, but when the device already is paired with the phone and I attempt to connect again it fails. I get to input a pin code then (standard should be 0000 according to manual), but it just says failed to connect.
If I unpair and pair them again it works (it doesn't ask for pin then).
Saw a fix on the Sony Ericsson forum where someone had this problem for Xperia, and they posted some cab file (Cyberon_Voice_Speed_Dial_v1.2___BT_Fix.cab), but I'm doubting it's possible to use on my Hero, and if it is, I have no idea how to do that.
Any thoughts?
Thanks.
You can't use any .cab's in android. and i think that fix is a registry fix and android doensn't have a fix.
i also noticed that bluetooth doesn't work without errors i hope that it will be fixed with android 2.0 we have to wait. but i didn't had any problems with my BT headset it also pairs automaticly.
Yeah I thought it wouldn't work... Well hoping for a fix.
Same problem here.
Yes I got the same problem with it not reconnecing. You can get it to work evensually by turn you bluetooth off and on afew time but i find it quicker just to unpair then repair each time. But apart for that, it works and sounds great.
Isn't 1234 the correct standard code ?
Problems with Bluetouth Headset Jabra BT3030
I have the same probleme, for me Jabra BT3030 Headset works wery well with WM 5,and 6 but doesn't works with WM6,1 or WM6,5
Is anyone has a solution or tips.
HTC Touch Cruise (P3650)
WM6,5
Manila 2D v2.0 build 19191432.04
Thanks.
Jabra BT3030 Headset with HTC
Yes, good news for me .
I did finaly fix my bluetouth Jabra BT 3030 with WM6.5 when I upgraded my HTC Touch Cruise from this (Hotfix to enhance the security mechanism of Bluetooth service)
http://www.htc.com/europe/supportdownloadlist.aspx?p_id=59&act=sd&cat=0
Now it works very well., I was a good hotfix for bluetouth
HTC Touch Cruise (P3650)
WM6,5
Manila 2D v2.0 build 19191432.04
Had the same problem with the BT3030 but suddenly it's not doing it anymore!
Just works great!
i bought the same one ... guys how many hours it should take for charge ? also i am very confused with the lights red. yellow n etc etc is there anyone using the same one ?& can give me bit manual how to use it .? would be very grateful..
http://www.jabra.co.uk/sites/Jabra/.../BT3030/Documents/UM/BT3030_UM_UK_EN_3124.pdf
sadape said:
http://www.jabra.co.uk/sites/Jabra/.../BT3030/Documents/UM/BT3030_UM_UK_EN_3124.pdf
Click to expand...
Click to collapse
Thanks Manual is really awesome .. that works
I've also had some strange problems pairing. Try holding the call button in for 6-7 seconds(instead of the 2-3 seconds) till the device shine solid blue and then pair from other device. This is the method I used to pair to the PC. Goodluck
hi guys, just started using MIUI for a few weeks but when trying to use bluetooth through to car stereo when i try to connect this screen happens:
and it just stays like that... any tips or workarounds or why i cant i assume see a accept pairing request button?
MIUI 2.3.1.6
thanks in advance
try to use another radio
SOLVED! see my reply below
Hello all.
I just got my new LG V30. An amazing smartphone.
Only trouble I have is volume sync when using my Sennheiser PXC550 bluetooth.
Volume up and down on the headset does not sync with volume on the phone.
I have tested some other headset and the only one I managed to test out that the sync worked was with Sony WH-1000XM2.
Anyone here tested other headset and it's working?
Problem SOLVED!
LG Nordic raised the question to LG South-Korea and they came back with the following answer and solution:
"Volume sync with bluetooth can only be guaranteed with certain tested devices.
The list is as follows;
LG HBS series, Sony MW600 / WH-1000XM2 / WH-1000X,
Apple BeatsSolo Wireless, Plantronics Backbeat Go,
Jabra MOVE / COACH / PULSE, Bose QuietComfort 30/35,
B&O H5 / H7 / H9 / H9i
This is also probably given if they have the correct AVRCP version.
Regardless; We have a tip that can make it work anyway;
1. Connect smartphone with Bluetooth headset.
2. Settings> Network> Bluetooth> Select the headset settings icon (right)>
Edit the name of the device> Rename the device name as "ABS-DO-ENABLE".
3. Disconnect the headset> Reconnect the headset."
I have testet this on my Sennheiser PXC550 and it works!
Volume now syncs on BT.
Hey thanks a thousand times! I have the same headset (PXC 550). The best piece of hardware I ever owned. I will try that tip because this was the only point I disliked.
So lucky I came across your thread
---------- Post added at 08:36 PM ---------- Previous post was at 08:20 PM ----------
Worked for me too! Thanks again.
Nice tip! Works for my BT headset also. Any idea how to make it work for more than one BT device - not connected at the same time, but I have a few different headsets.
Thanks for this. Just got it working with my Jabra elite 65t. Was driving me crazy!
fclifton said:
Nice tip! Works for my BT headset also. Any idea how to make it work for more than one BT device - not connected at the same time, but I have a few different headsets.
Click to expand...
Click to collapse
This was driving me bonkers too, but I think I've got it figured out. Name each device with the same prefix, but add a bit to the end to specify which each is. Here's how I have it set up:
ABS-DO-ENABLE (headphones)
ABS-DO-ENABLE (car)
ABS-DO-ENABLE (speakers)
Wonky, yeah, but at least it's working now.
Hey there,
i can confirm this workaround exept on behalf of the of the time this is working. When i delete my device from known devices and reconnect it afterwards while renaming it to the above pattern it works exactly one time. After a reconnect it behaves like before. Im assuming there might be some side effect regarding the used connection protocol. Do you know which AVRCP Version is used at your device ?
Tymo55 said:
Hey there,
i can confirm this workaround exept on behalf of the of the time this is working. When i delete my device from known devices and reconnect it afterwards while renaming it to the above pattern it works exactly one time. After a reconnect it behaves like before. Im assuming there might be some side effect regarding the used connection protocol. Do you know which AVRCP Version is used at your device ?
Click to expand...
Click to collapse
Hi, @Tymo55.
My headphone device, Sennheiser PXC550, uses AVRCP ver. 1.5 according to the manual.
I recommend you run the native LG app "Smart doctor", "optimize device" and reboot your LG V30-phone.