I've tried about a million times now and can not get my Gtab into clockwork recovery. I downloaded the internal version of clockworkmod and hooked my gtab up to the computer and placed the clockworkmod zip in the recovery folder and unzipped it. Then I turned my device off and held down the power button + vol + it then says "Recovery key detected" and acts like its installing. Then It reboots and I turn it off again and it just keeps doing the same thing saying "
recovery key detected" and won't boot into clockwork!!!! Advice please?? And I know this is a noob question, I do. I tried following the instructions on the stickies but they're vague as to which clockwork zip I am to download??? Please help. Thanks!!!
From what I gather, after you download the internal zip you unzip that so you see the update.zip file & recovery folder. You move both of those to the root of the g-tab which would be /sdcard. I haven't done it yet since mine is charging right now.
Trying it now
GOLDEN....Finally! Thank you sir!
peurifoyd said:
I've tried about a million times now and can not get my Gtab into clockwork recovery. I downloaded the internal version of clockworkmod and hooked my gtab up to the computer and placed the clockworkmod zip in the recovery folder and unzipped it. Then I turned my device off and held down the power button + vol + it then says "Recovery key detected" and acts like its installing. Then It reboots and I turn it off again and it just keeps doing the same thing saying "
recovery key detected" and won't boot into clockwork!!!! Advice please?? And I know this is a noob question, I do. I tried following the instructions on the stickies but they're vague as to which clockwork zip I am to download??? Please help. Thanks!!!
Click to expand...
Click to collapse
Hmm?.. I think the issue you are having is moving the update zip into the recovery folder.
when you extract the files from the zip file extract them to the main directory "/SCARD" and thats it.
After you extract it you should see (in that directory) a folder that says "Recovery" , within that folder there should be a file named "Command" and thats it, no more files in there.
Also in that main directory you should see an "update.zip" file, leave it there. DON'T MOVE IT into the recovery folder.
from there follow directions to boot into recovery mode.
1) Power down
2) Press and Hold down volume up + rocker
3) Press and hold Power Button
4) when device powers on you will see "Recovery Key Detected"
5) release buttons
6) recovery will install and reboot as normal.
7) Power down and follow steps 1 through 5 again.
8) You should be in recovery mode now.
Edit:
Took too long to make this post!! LOL
my noob questions...what version did you use and can you post a link to it?? i am getting my g tab today!!
thx...
Follow the instructions on this link.
http://forum.xda-developers.com/showthread.php?t=865245&highlight=clockwork
Rumbleweed said:
Follow the instructions on this link.
http://forum.xda-developers.com/showthread.php?t=865245&highlight=clockwork
Click to expand...
Click to collapse
thx. i'm up n runnin vegan 5....
Tekrhino, I feel stupid but I have to ask for your help re: this same issue. It seems so clear on what to do from your instructions but I still can't get clockwork recovery to load. I'm having the exact same issue of not getting into clockwork recovery so I must be doing something wrong.
Maybe by telling my steps you can get me on the right path.
1. Downloaded clockwork mod to desktop.
2. extracted update.zip now I have a file that says update unzipped.
3. attached gtab to usb, recognized by computer as removable disk.
4. click on "open folder to view files and see list of different files on gtab
5. copy and paste recovery and update unzipped to this window and disconnect gtab from computer and then try to do the above mentioned steps to get into recovery. get the recovery key is detected message but can't get into clockwork recovery.
I must be doing something wrong but can't figure out what! Any suggestions that can point out the error of my process will be very much appreciated.
GGGwhatever!!
You don't need to unzip update.zip. You just put it in the /sdcard directory and the reboot to CWM and take the CWM options to run it.
Rev
Download CWM to your computer.
Uncompress it get two files (recovery and update.zip) Do not unzip update.zip
put these two files in your root directory on your Gtab ( SDCARD)
Hold Vol+ button turn on.
Sit back and watch
GGGTABBB! said:
Tekrhino, I feel stupid but I have to ask for your help re: this same issue. It seems so clear on what to do from your instructions but I still can't get clockwork recovery to load. I'm having the exact same issue of not getting into clockwork recovery so I must be doing something wrong.
Maybe by telling my steps you can get me on the right path.
1. Downloaded clockwork mod to desktop.
2. extracted update.zip now I have a file that says update unzipped.
3. attached gtab to usb, recognized by computer as removable disk.
4. click on "open folder to view files and see list of different files on gtab
5. copy and paste recovery and update unzipped to this window and disconnect gtab from computer and then try to do the above mentioned steps to get into recovery. get the recovery key is detected message but can't get into clockwork recovery.
I must be doing something wrong but can't figure out what! Any suggestions that can point out the error of my process will be very much appreciated.
Click to expand...
Click to collapse
I just got my tablet today and am still playing around with the stock, but from what I read I think your mistake is unzipping the "update.zip" file.
You only unzip the clockwork mod file you downloaded. Then you have two files: 'update.zip' and 'recovery' (folder). Leave the update.zip alone, don't unzip it and put these two files onto your gtab. Either internal storage (sdcard) or microsd card (sdcard2), depending on which clockwork file you have.
Thanks Rev! I know it is something simple but it was what I needed to get started.
Now I can play!
Newbie possible screwup
Help, followed install for Cwd and all get is the recovery reconized and it just stays on theviewsonic open page. Willnot go any further it is stuck.
I messed up the G Tablet soon after receiving it.
Here are two links with information on how to get it restored.
Viewsonic GTablet For Dummies
Guide - Restore G Tablet after a failed Recovery Mode update
Hope this helps.
djab67
(If I have helped, please hit the "Thanks" button)
I ordered my g tablet yesterday and cant wait for it to come in. So tonight I am downloading a rom and clockworkmod v8 so I will be ready when it comes in. However I need a little help. I read the guide on installing clockworkmod and a rom but cant firgure something out. It says to un zip the files into the root of the device. When it means un-zip does it mean to "right click" than "extract all" Because when I do this the recovery folder doesn't have the zipper on it anymore but the update folder still does. Is this right?
The recovery folder and the zip file called update is what you will need to transfer to the root of your SD card when you connect your tablet to the PC. The recovery folder should not be in a zip format, but the update file should be.
ok thanks. But both folders go in the root right?
Yes. Then boot into recovery and it will start the update after so many seconds.
the update folder just says "update" it doesn't say update.zip however it is a zipped folder. Is it the same thing?
Most operating systems, referring to Mcrosoft, hides the extensions of files, but if it has the look of a zip file or what ever software you may be using, I would assume that would be the update file just not showing the .zip extension.
You are making it hard. Just do this.
Hook up Gtablet to your pc by USB. See which drive your pc asigns to your GTablet. Download the correct Clockwork Mod you need.
Unzip it to a folder on your pc. Then just drag and drop the two files after zipping to the drive your pc assigned to your Gtablet. On mine it is G. Yours may be F.
Then just power down your GTablet and then power up holding down power and volume + till you get Viewsonic screen and a message in upper left corner that recovery has started.
Then go here: http://forum.xda-developers.com/showthread.php?t=865245
If ClockworkMod installed, start with Part 1, step 6 or 7. READ IT ALL.
Everything looked like it was going good... I made a folder names cminstall and put the 3 files in there....opened up cmd prompt and typed this is "novacom boot mem:// < ACMEInstaller" Everything was installing good until i got this error
"looking for the install images... initial install files not found. please download it from touchpad.linuxhacker.ru and put in sminstall folder on media partition. the name should start with update-cm end end with .zip..."
Anyone else have this problem? I searched google and found a guy with this prob but no solution.
I pressed the home and power button and it got me to the normal hp os
What did I do wrong?
Any help would be great!
Have you tried just the basics like downloading the files again and perhaps with a different browser/site to make sure they are not corrupt?
johnnyboy1 said:
Everything looked like it was going good... I made a folder names cminstall and put the 3 files in there....opened up cmd prompt and typed this is "novacom boot mem:// < ACMEInstaller" Everything was installing good until i got this error
"looking for the install images... initial install files not found. please download it from touchpad.linuxhacker.ru and put in sminstall folder on media partition. the name should start with update-cm end end with .zip..."
Anyone else have this problem? I searched google and found a guy with this prob but no solution.
I pressed the home and power button and it got me to the normal hp os
What did I do wrong?
Any help would be great!
Click to expand...
Click to collapse
You either don't have a CMINSTALL folder on the root of your Touchpad, or your zip files have (1)s or (2)s behind them and need to be removed, or you just didn't but the files in the folder at all.
help me please
Hi to everyone, my name is Federico and I have the same problem!
When I started the ACMEInstaller after some minutes appeared the message "Looking for the install images...
Initial install files not found.
Please download it from touchpad.linuxhacker.ru
and put in sminstall folder on media partition
the name should start with update-cm and end with .zip"
the main issue is tha I'm not able to restar the device =(
How can I do? Please help me.
What are you installing and what exactly did you put in the cminstall folder.
Details are very useful
hold down the off button and the home button for a good 20 seconds, this is hardcoded to the device and should reset it
johnnyboy1 said:
Everything looked like it was going good... I made a folder names cminstall and put the 3 files in there....opened up cmd prompt and typed this is "novacom boot mem:// < ACMEInstaller" Everything was installing good until i got this error
"looking for the install images... initial install files not found. please download it from touchpad.linuxhacker.ru and put in sminstall folder on media partition. the name should start with update-cm end end with .zip..."
Anyone else have this problem? I searched google and found a guy with this prob but no solution.
I pressed the home and power button and it got me to the normal hp os
What did I do wrong?
Any help would be great!
Click to expand...
Click to collapse
should be novacom boot mem:// < ACMEInstaller2
Depending on what you were trying to flash, you may need ACMEInstaller2.
You need a folder on your PC named cminstall and the same folder on your tab. In that you'll need moboot, cwm, acmeinstaller2 and your rom.
Cm9 needs acmeinstaller2
Sent from my DROIDX using XDA App
After 3 days tried to find out how to recovered or fix bootloop/brick ME170C, here is the way which was succeed for me.
1. Download latest firmware from ASUS website
the best way using complete firmware (containing stock rom) like this version UL-K017-WW-11.2.3.18.2-user, if succeed then later on you can continue with OTA system update
2. Rename the firmware file to K017_sdupdate.zip and put on SD card then Insert the SD card into a tablet. (Use good one SD card, Sandisk perfect I don't know others)
3. Download flashtools and USB driver at the bottom of this thread
4. Enter the DROIDBOOT, for this purpose on the tablet off push and hold button volume + and power then connect USB cable to tablet and PC.
5. Open your firmware archive and copy or drag & drop the boot.img, fastboot.img, splashscreen.img into Flashtools folder ( in computer )
6. go to flashtools folder and then push button shift and right click together and choose “Open command windows here”, to start open CMD on the right folder (in computer)
7. Test your device by typing fastboot devices on that cmd (in computer)
8. Enter the queue codes on CMD; (in computer)
fastboot erase cache
fastboot erase userdata
fastboot erase system
fastboot flash boot boot.img
fastboot flash fastboot fastboot.img
fastboot flash splashscreen splashscreen.img
fastboot reboot-bootloader
8. Disconnect the USB cable and select the SD update or Recovery.
9. Take your coffee and sit, walaaaaaaa I see you are smiling
I am curious , is it work for others ASUS tablet? do with your own risk, but btw with this step I did wake up a hard brick devices.
Tag [ Asus memopad fonepad zenfone ME170 brick, bootloop, stuck on asus logo, boot problem, solved brick, guide how to]
So awesome you figured this out! Glad it worked out for you and I'll be saving this in case I find myself in the same boat. Thank you for this!!
Sent from my Nexus 6
K01A, aka ASUS MeMO Pad ME170CX
Prod date 2014-10 IIRC.
I appreciate you taking time to create this thread, have been unable to flash stock firmware to the ME170CX using just the ME170CX itself. ASUS website just mentions a SOP method and when I insert SD that has had the firmware files which have been extracted (1) time to the SD card, the prompt that is supposed to "pop-up" on the taskbar as mentioned in the PDF's I found online about the SOP method does NOT occur.
(I have 2 ME170CX's about 30-days old running 4.4.2, firmware Version WW_V11.2.3.27 in which one of them all the sudden the camera app crashes 100% of the time, then gives a "No camera is found" error message.
Beyond a hardware issue no-one knows what causes this beyond (1) poster that mentioned he thought problem first occurred after hitting the "Home" button right after hitting the cam icon and the thought is the app gets confused by this and the app/firmware for the camera gets corrupted.
Reset via OS itself. Wiping data and choosing "Recovery" in DROIDBOOT with "FASTBOOT" text at bottom of screen didn't make any difference. Camera is dead, dead, dead.
Figured I'd re-flash with same Version WW_V11.2.3.27, if that doesn't work try Version WW_V11.2.3.28 before RMA'ing it back to ASUS so I appreciate you listing the steps, and also attaching the needed files.)
***************
Question about Step 2, Please clarify:
2. Extract (archive in archive) and throws to the SD card. Rename the file to K017_sdupdate.zip and Insert the flash drive into a tablet. (Use good one SD card)
Click to expand...
Click to collapse
To clarify you are saying to extract the firmware from the "zip" package of zip that matches the firmware specific to the device from ASUS, which itself contains a zip file named IFWI.ZIP (1 ), one time, then rename the file named IFWI.ZIP (which contains 4 Bin files) to K017_sdupdate.zip.
Upon extraction process completing and renaming the zip you then copy the contents over to a known good MiroSD of at least 2GB which is formatted FAT32 to the ROOT of the drive.
IE: You do not extract the zip within the archive, you're just renaming IFWI.ZIP to K017_sdupdate.zip?
OR are you saying to extract the BINS also?
If so do these go in the ROOT of the SD card?
Another question, is there a reason for renaming IFWI.zip to K017_sdupdate.zip?
.
WeAreNotAlone said:
K01A, aka ASUS MeMO Pad ME170CX
Prod date 2014-10 IIRC.
I appreciate you taking time to create this thread, have been unable to flash stock firmware to the ME170CX using just the ME170CX itself. ASUS website just mentions a SOP method and when I insert SD that has had the firmware files which have been extracted (1) time to the SD card, the prompt that is supposed to "pop-up" on the taskbar as mentioned in the PDF's I found online about the SOP method does NOT occur.
(I have 2 ME170CX's about 30-days old running 4.4.2, firmware Version WW_V11.2.3.27 in which one of them all the sudden the camera app crashes 100% of the time, then gives a "No camera is found" error message.
Beyond a hardware issue no-one knows what causes this beyond (1) poster that mentioned he thought problem first occurred after hitting the "Home" button right after hitting the cam icon and the thought is the app gets confused by this and the app/firmware for the camera gets corrupted.
Reset via OS itself. Wiping data and choosing "Recovery" in DROIDBOOT with "FASTBOOT" text at bottom of screen didn't make any difference. Camera is dead, dead, dead.
Figured I'd re-flash with same Version WW_V11.2.3.27, if that doesn't work try Version WW_V11.2.3.28 before RMA'ing it back to ASUS so I appreciate you listing the steps, and also attaching the needed files.)
***************
Question about Step 2, Please clarify:
To clarify you are saying to extract the firmware from the "zip" package of zip that matches the firmware specific to the device from ASUS, which itself contains a zip file named IFWI.ZIP (1 ), one time, then rename the file named IFWI.ZIP (which contains 4 Bin files) to K017_sdupdate.zip.
Upon extraction process completing and renaming the zip you then copy the contents over to a known good MiroSD of at least 2GB which is formatted FAT32 to the ROOT of the drive.
IE: You do not extract the zip within the archive, you're just renaming IFWI.ZIP to K017_sdupdate.zip?
OR are you saying to extract the BINS also?
If so do these go in the ROOT of the SD card?
Another question, is there a reason for renaming IFWI.zip to K017_sdupdate.zip?
.
Click to expand...
Click to collapse
some firmware when you download it from asus site ZIP compresed twice, you can rename it directly from WW_V11.2.3.28.zip to K017_sdupdate.zip, if your device is K01A try to renaming firmware to K01A_sdupdate.zip and then put in SD card (do not created any folder in SD card ). the key to success is the SD card compatibility with ASUS DROIDBOOT, I was using Sandisk SD card. I did format fat32 the SD card and insert in another android devices first and then put the renamed firmware file there.
inside firmware file there is boot.img, fastboot.img and splashscreen.img you need to extract it in flashtool/fasboot folder and then flashing it your tablet. this trick to make firmware recognize correct devices to be update.
try again.
sevensvr said:
some firmware when you download it from asus site ZIP compresed twice, you can rename it directly from WW_V11.2.3.28.zip to K017_sdupdate.zip, if your device is K01A try to renaming firmware to K01A_sdupdate.zip and then put in SD card (do not created any folder in SD card ). the key to success is the SD card compatibility with ASUS DROIDBOOT, I was using Sandisk SD card. I did format fat32 the SD card and insert in another android devices first and then put the renamed firmware file there.
inside firmware file there is boot.img, fastboot.img and splashscreen.img you need to extract it in flashtool/fasboot folder and then flashing it your tablet. this trick to make firmware recognize correct devices to be update.
try again.
Click to expand...
Click to collapse
RE: boot.img, fastboot.img and splashscreen.img you need to extract it in flashtool/fasboot folder ???????
Having some progress, renaming ifwi.zip which contains (4) bin files when Recovery was selected caused the robot with the Updating System Settings to appear, but a couple of seconds later it said ERROR with the robot laying on it's back, then it exits. Device reboots as normal.
To clarify:
WW_V11.2.3.28.zip download from ASUS was extracted with a Windows computer,
WW_V11.2.3.28.zip extracting /creating following folders, files, then the contents were copied to the ROOT of a MicroSD card formated Fat32
1: boot.img, fastboot.img and splashscreen.img (TO ROOT)
2: ifwi.zip to ROOT. (contains (4) bin files, is this supposed to be extracted to I assume folder by same name off root? OR does this ZIP file just get renamed?)
3: System folder
4: Recovery folder
5: META-INF folder
I do not see a flashtool/fasboot folder. (Fastboot, right?)
Q: Is boot.img, fastboot.img and splashscreen.img supposed to be in a folder named "Flashtool" OR are they supposed to be in folder named "Fastboot" with a pathway of Root (Drive) D:/Flashtool/fastboot ?
.
(NOTE ALL OF THIS IS BEING DONE ON THE DEVICE ITSELF, with contents on SD card.)
Still getting the ERROR! message wit the Adroid robot that is laying on his back.
The zip file that extracts from the main zip WW_V11.2.3.28.zip is named:
ifwi.zip...
I have left a copy of it in the ROOT, plus copied it and renamed it to
K01A_sdupdate.zip
K017_sdupdate.zip
LEAVING COPIES OF ALL IN THE ROOT OF THE SDCARD.
Q: If more than (1) zip is present does this confuse fastboot? OR does fastboot automatically look for zip zip which matches model ID of device? (K01A)
I have left copies of boot.img, fastboot.img and splashscreen.img in the ROOT of the drive.
AND
Created: (ROOT) flashtools/fastboot with *img files in it.
Created: (ROOT) fastboot with *img files in it.
Copied the *img files to under "Flashtools" folder in flashtools/fastboot.
Figuring all the bases would be covered. (EG: *img Files in ROOT, files in Flashtools, Flashtools/fastboot, and a folder named fastboot as well.
Q: I've noticed on the SD card files appearing that previously were not there, when the flash aborts is there some kind of file or files you need to delete, or is it ok to leave the newly generated files there?
---------- Post added at 03:43 AM ---------- Previous post was at 03:37 AM ----------
Deleted:
ifwi.zip.
K017_sdupdate.zip
Tried:
K01A_sdupdate.zip
Still getting robot on it's back with ERROR!
who said you need to renaming ifwi.zip, What you need is read all instruction carefully,
do not put more than 1 zip file in SD card only firmware file which is already renamed to K017_sdupdate.zip, and use good brand SD card.
I successfully complete all step after "Installing system update" nothing change again stuck on asus logo.
commando987 said:
I successfully complete all step after "Installing system update" nothing change again stuck on asus logo.
Click to expand...
Click to collapse
when installing update, the robot end with error or not?, the installing bar moved till finish ? the installing process will take 3 to 5 minutes.
if you did all above and still got stuck on asus logo, try to change the firmware with this version UL-K017-WW-11.2.3.18.2-user, if succeed then you can continue with OTA system update
My Asus MemoPad ME170C has risen again!
sevensvr said:
After 3 days tried to find out how to recovered or fix bootloop/brick ME170C, here is the way which was succeed for me.
1. Download latest firmware from ASUS website
2. Rename the firmware file to K017_sdupdate.zip and put on SD card then Insert the SD card into a tablet. (Use good one SD card, Sandisk perfect I don't know others)
3. Download flashtools and USB driver at the bottom of this thread
4. Enter the DROIDBOOT, for this purpose on the tablet off push and hold button volume + and power then connect USB cable to tablet and PC.
5. Open your firmware archive and copy or drag & drop the boot.img, fastboot.img, splashscreen.img into Flashtools folder ( in computer )
6. go to flashtools folder and then push button shift and right click together and choose “Open command windows here”, to start open CMD on the right folder (in computer)
7. Test your device by typing fastboot devices on that cmd (in computer)
8. Enter the queue codes on CMD; (in computer)
fastboot erase cache
fastboot erase userdata
fastboot erase system
fastboot flash boot boot.img
fastboot flash fastboot fastboot.img
fastboot flash splashscreen splashscreen.img
fastboot reboot-bootloader
8. Disconnect the USB cable and select the SD update or Recovery.
9. Take your coffee and sit, walaaaaaaa I see you are smiling
I am curious , is it work for others ASUS tablet? do with your own risk, but btw with this step I did wake up a hard brick devices.
Tag [ Asus memopad fonepad zenfone ME170 brick, bootloop, stuck on asus logo, boot problem, solved brick, guide how to]
Click to expand...
Click to collapse
I bought my memopad 170c just a couple of days ago and because of excitement i flash the wrong firmware and it went dead i tried the recovery method but nothing happens i'm beginning to get nervous as this tablet is a gift for my daughter but thankfully i found this site especially to your instruction did every step with my finger crossed and like what you said sit back and walaaaaa! my tablet err my daughter's tablet has risen again. thank you for sharing your knowledge.
sevensvr said:
when installing update, the robot end with error or not?, the installing bar moved till finish ? the installing process will take 3 to 5 minutes.
if you did all above and still got stuck on asus logo, try to change the firmware with this version UL-K017-WW-11.2.3.18.2-user, if succeed then you can continue with OTA system update
Click to expand...
Click to collapse
Installing bar not complete at the end but not give error and restart. After restart stuck on asus logo. Now i download version UL-K017-WW-11.2.3.18.2 and check it.
mapagmatyag said:
I bought my memopad 170c just a couple of days ago and because of excitement i flash the wrong firmware and it went dead i tried the recovery method but nothing happens i'm beginning to get nervous as this tablet is a gift for my daughter but thankfully i found this site especially to your instruction did every step with my finger crossed and like what you said sit back and walaaaaa! my tablet err my daughter's tablet has risen again. thank you for sharing your knowledge.
Click to expand...
Click to collapse
you welcome friend
commando987 said:
Installing bar not complete at the end but not give error and restart it. After restart stuck on asus logo. Now i download version UL-K017-WW-11.2.3.18.2 and check it.
Click to expand...
Click to collapse
it seems the tablet didn't read your SD card, to assure SD card problem when the robot appear while system update press buttom vol + and - rapidly to show installing status.
if the tablet didn't read ur SD card try to use another SD card
BIG Thanks
I've been stuck with the bricked 2 day old tablet for at least 3 months. Today I did the procedure you described and it worked. I had to install version V11.2.3.18.2 and then, once unbricked, apply latest version update.
Again, thanks a lot!.. Best regards.
mnabarro said:
I've been stuck with the bricked 2 day old tablet for at least 3 months. Today I did the procedure you described and it worked. I had to install version V11.2.3.18.2 and then, once unbricked, apply latest version update.
Again, thanks a lot!.. Best regards.
Click to expand...
Click to collapse
happy to heard it
Hi, am trying to fix my ME170CX because an original root attempt that failed and am getting a demo error message that won't go away.
I tried following all your instructions to fix this but it gets stuck "waiting for device" once I begin entering the commands.
I have tried multiple sd cards (including a sandisk) and both the V11.2.3.27 & V11.2.3.28 firmware versions to no avail.
I also tried naming the zip file K017 & K01A.
I am also wondering why we need to download the USB driver file? I don't see anywhere in your instructions on what to do with this.
Any help would be greatly appreciated.
Mike
mashton70 said:
Hi, am trying to fix my ME170CX because an original root attempt that failed and am getting a demo error message that won't go away.
I tried following all your instructions to fix this but it gets stuck "waiting for device" once I begin entering the commands.
I have tried multiple sd cards (including a sandisk) and both the V11.2.3.27 & V11.2.3.28 firmware versions to no avail.
I also tried naming the zip file K017 & K01A.
I am also wondering why we need to download the USB driver file? I don't see anywhere in your instructions on what to do with this.
Any help would be greatly appreciated.
Mike
Click to expand...
Click to collapse
Youll want to get your answer from him but i think i may be able to help. You need to install usb drivers so you can access abd and give commands to your tablet. Which i think is why it just says waiting for device... I could be wrong though....
Sent from my Nexus 6
anthonyg45157 said:
Youll want to get your answer from him but i think i may be able to help. You need to install usb drivers so you can access abd and give commands to your tablet. Which i think is why it just says waiting for device... I could be wrong though....
Sent from my Nexus 6
Click to expand...
Click to collapse
OK, I finally got the usb drivers working on my computer and made it through all commands which is much further than I was getting before.
I got to step 8 "Disconnect the USB cable and select the SD update or Recovery" and selected "Recovery" in DROIDBOOT (I don't have an "SD update" option there) and after like 1 second of "installing system updates" I get the android falling over guy error and then it hangs on the asus splash screen for ever.
download ME70CX for ME170CX
anthonyg45157 said:
Youll want to get your answer from him but i think i may be able to help. You need to install usb drivers so you can access abd and give commands to your tablet. Which i think is why it just says waiting for device... I could be wrong though....
Sent from my Nexus 6
Click to expand...
Click to collapse
have you been able to restore it ?
Can NOT use download of ME170C
Use download of ME70CX. Just did it, and tablet back to "almost" normal.
I have wifi button issue now. Button is stuck.
bye
ydobon.999 said:
have you been able to restore it ?
Can NOT use download of ME170C
Use download of ME70CX. Just did it, and tablet back to "almost" normal.
I have wifi button issue now. Button is stuck.
bye
Click to expand...
Click to collapse
That did it!
I used the firmware ME70CX and renamed the file "K01A_sdupdate.zip" and followed all of the other steps as per the original instructions and got my ME170CX working again but for one problem. . . I was still getting the "demo has stopped" error! So I proceeded to attempt root again, this time with RootZenFone-1.4.6r and and now it's working perfectly and rooted as well!
Many thanks to all!!