Hey all,
Does anyone here have any tips to protect the camera lens of this phone? It sticks out the back a little and I'm afraid it will get scratched over time. Is that too made of gorilla glass, is it scratch resistant? Or should i go for a case.
Problem with the case is that dust is getting accumulated between Bezel and screen and i hate it.
I have some scratches on the lens, but haven't noticed any affect of that in photos.
But if you want not to scratch it more, then either you have to put a protective scratch guard, you can see Martinfield website for that OR you have to use a case which will cover the lens from scratch when you place it on a flat hard surface. You can use a good case for that, like- CM Tough, Pop, SGP Neo etc., but those cases as you said will keep the dust inside the bezel and the case. If you don't like that, then you have to use a Flip Top cover, some leather good ones are available like, SGP Argos, Zenus Prestige Carbon etc.
Regards.
Sent from my GT-I9100
thanks Bro.
I have just thinking about that yesterday. I am afraid that it could get scratch while dragging the phone off the table or some other surface...
My idea: buy very cheap screen protector (1 €/$), cut it and place it on the camera lens. I will do that as soon as I buy one.
Related
Have you left the camera bezel as is or have you covered it up with something?
When I got the phone I was worried about it getting scratched up so I took a screen protector and cut out a square to go over the camera of course I also cut out a hole for the camera to see through but for those who have done nothing do you find the bezel or camera lens has gotten scratched up?
I guess I would also like to know about the silver bezels which go around the width of the phone - scratched up from daily use?
No issue here, but i keep the device in my jacket pocket and never in my pants pocket.
Especially levi fabric...(sand paper )....g
First 4 months i had a flip cover on my phone so it was protected a little bit. Last 5 months has been naked stock cover. No issues at all. Carry it in front pocket all the time. Of course it was mostly summer so it was in shorts pockets but have carried it in my jeans pockets numerous times.
from a galaxy far far away....
no scuffs or scratches... but the battery cover has some pretty good signs of wear. the silver trim around the lens also has some wear if you look closely but the camera cover does not have anything
kingofkings11 said:
Have you left the camera bezel as is or have you covered it up with something?
When I got the phone I was worried about it getting scratched up so I took a screen protector and cut out a square to go over the camera of course I also cut out a hole for the camera to see through but for those who have done nothing do you find the bezel or camera lens has gotten scratched up?
I guess I would also like to know about the silver bezels which go around the width of the phone - scratched up from daily use?
Click to expand...
Click to collapse
for times when I dont have my Otterbox Defender case on it (rare), I have a Skinomi body skin protector on it and the Martin Fields screen+camera protector!
Full body coverage x2! the Martin Fields camera lens protector fits PERFECTLY, and from my own before/after experience, doesn't cause any visible distortion.
My job entails me crawling around under houses in the dirt, so I'm looking for a case that will help protect the N6 from dirt and cover the screen so it hopefully doesn't get cracked. Does the Unicorn Beetle Pro sound like the case for me?
Yeah, the built-in protector will help a bit when it comes to dirt getting to the phone, and the shell protection is good for being single-layer. Plus, it has built-in covers for the ports.
I did find that dirt can still get in in the seam between its built-in cover and the shell frame, but it didn't reach the phone easily due to the inner glue line.
I'd offer my barely used Beetle Pro case, but I removed the built-in protector when deciding to use a different screen cover - then, I went with dual-layer cases for even more shock safety.
- wader
I purchased the Beetle Pro along with a intelliARMOR PRO edge to edge glass screen protector. Is the Beetle Pro the only case with a holster or something that actually covers the screen? Used to like the OtterBox, but they don't hold up well and don't think they ever made a N6 case.
https://www.amazon.com/gp/aw/d/B00OGYP52Y/ref=yo_ii_img?ie=UTF8&psc=1#
I work in maintenance and am always dirty, greasy, crawling around and under equiptment. I use my phone a lot for manuals, pics, emails and such. I had the above case for about a week. I scratched the screen protector pretty quickly and noticed grit getting under the case pretty easy. I know it's not the greatest build quality, but quickly decided that 2 piece cases blow. I've bought a used tablet that had an otter box case and the back of the tablet has scratches all other the back from being on it.
Anyway I've learned that in my line of work, that a simple jelly type case and no screen protector seem to do best. The case is good for the occasional drop and no grit to get trapped between the screen and protector. I'm just very aware to keep it in my front pocket and nothing else goes in that pocket. I do remove the case occasionally to clean the phone and case if any grit gets build up, but it is usually little too none. If i do get grit in my pockect from dirt, welding, dust, etc. I just clean out my pocket best i can and the phone goes back in. No issues or scratches so far after a couple of months.
Not sure about tempered screen protectors, but IMHO anything that I can't remove easily to clean under is just asking for trouble with scratches. My two cents anyway.
Mike
When I first got my S8+, I was worried the back glass would scratch easy (turns out I was right ), so I wanted to protect it, even though I knew I would have a case on it. I've seen dirt get between phones and cases before and cause horrible scratches.
I first tried a clear wet application skin from BSE, but I could never make it look right. The midnight black shoes every imperfection and bubble, whereas my wife's Orchid Grey looks perfect with the skin on. You can't tell it's there, even on the sides.
So I began thinking it would be nice if someone made a tempered glass protector for the back. The sides are curved, but so is the screen, and there's plenty of TGSPs on the market. But I couldn't find any.
Then last week I saw one on Amazon. It comes with a full screen TGSP, a TGP for the back, and a TGP for the camera. Link is below.
It appears the back protector is like other TGSPs. It has no glue on the middle, just along the edges. That's not a big deal, as I would apply it like I did my TGSP. I would remove the adhesive strip on the edge and use LOCA to adhere it fully to the phone. Most camera lens TGPs get horrible reviews on Amazon, so it would likely go in the trash.
I'm trying to decide what to do. Here are my pros and cons, but I wanted everyone else's opinion, and also want to know if anyone else has any experience with this set. Again, I'm currently using a TGSP for the screen, so this is a question about the TGP for the BACK.
Pros:
*Protection for the back cover as well as the front.
*Protects from scratches and adds some drop protection
*Protectors are both glass, so it would still feel like a naked device.
*Back protector is Crystal clear, and with LOCA, would show off the beautiful black back glass without any bubbles, glare, etc.
*Glass doesn't get marks and dents like wet application protectors.
Cons:
*It would (probably) be too thick to use a case, so increased chance of damage if dropped.
*These TGSPs typically use cheap oleophobic coatings, so it would still be a fingerprint magnet on the back.
*This would leave a ridge around the screen and the back protector, so it MAY make it uncomfortable to hold.
*No protection for the side frame
*It will scratch (but can always be replaced
*I wish the cutouts were more precise. I'd like three separate cutouts for camera and sensors, not one big one. Would make it more seemless.
Again, looking for other thoughts and opinions and any experience.
No offense, but if all you have to say is that you go naked and have no scratches, or that you don't like screen protectors, then please don't reply. I'm not interested in a screen protector debate. I'm only interested in your opinions about this particular set and using a protector on the back. Also, I know about the liquid nano stuff and have no interest in it. I've seen all the reviews.
Thanks!
JimBird Tempered Glass Screen Protector Front + Back + Camera Lens Protector For Galaxy S8 Plus S8+ 9H Anti-Scratch Anti-Fingerprint https://www.amazon.com/dp/B073S4YZW1/ref=cm_sw_r_cp_apa_MohHzbHWHA99A
Mr. Orange 645 said:
When I first got my S8+, I was worried the back glass would scratch easy (turns out I was right ), so I wanted to protect it, even though I knew I would have a case on it. I've seen dirt get between phones and cases before and cause horrible scratches.
I first tried a clear wet application skin from BSE, but I could never make it look right. The midnight black shoes every imperfection and bubble, whereas my wife's Orchid Grey looks perfect with the skin on. You can't tell it's there, even on the sides.
So I began thinking it would be nice if someone made a tempered glass protector for the back. The sides are curved, but so is the screen, and there's plenty of TGSPs on the market. But I couldn't find any.
Then last week I saw one on Amazon. It comes with a full screen TGSP, a TGP for the back, and a TGP for the camera. Link is below.
It appears the back protector is like other TGSPs. It has no glue on the middle, just along the edges. That's not a big deal, as I would apply it like I did my TGSP. I would remove the adhesive strip on the edge and use LOCA to adhere it fully to the phone. Most camera lens TGPs get horrible reviews on Amazon, so it would likely go in the trash.
I'm trying to decide what to do. Here are my pros and cons, but I wanted everyone else's opinion, and also want to know if anyone else has any experience with this set. Again, I'm currently using a TGSP for the screen, so this is a question about the TGP for the BACK.
Pros:
*Protection for the back cover as well as the front.
*Protects from scratches and adds some drop protection
*Protectors are both glass, so it would still feel like a naked device.
*Back protector is Crystal clear, and with LOCA, would show off the beautiful black back glass without any bubbles, glare, etc.
*Glass doesn't get marks and dents like wet application protectors.
Cons:
*It would (probably) be too thick to use a case, so increased chance of damage if dropped.
*These TGSPs typically use cheap oleophobic coatings, so it would still be a fingerprint magnet on the back.
*This would leave a ridge around the screen and the back protector, so it MAY make it uncomfortable to hold.
*No protection for the side frame
*It will scratch (but can always be replaced
*I wish the cutouts were more precise. I'd like three separate cutouts for camera and sensors, not one big one. Would make it more seemless.
Again, looking for other thoughts and opinions and any experience.
No offense, but if all you have to say is that you go naked and have no scratches, or that you don't like screen protectors, then please don't reply. I'm not interested in a screen protector debate. I'm only interested in your opinions about this particular set and using a protector on the back. Also, I know about the liquid nano stuff and have no interest in it. I've seen all the reviews.
Thanks!
Click to expand...
Click to collapse
I was thinking about the same thing, this post is very helpful.
Mr Orange, I am thinking on the same lines as you were. Did you end up buying the JimBird TGSP? If so, what are your opinions of it and how well did it work for you? It seems like something simple to offer, but so hard to find. Thanks!
I was just curious that how many of you use your phone without any protection? I just started using like that and it feels really nice. The hyper-cut diamond finish gives a good grip to the hand.
I really like the feel of the phone in the hand, nicest I've had to hold, and is the only phone I ever use a case with...I just know if I leave it out the case there will be an expensive accident.
I use it without cover but with a glass screen protector
I don't use any glass or cover. I buy nice designed phones to feel the nice full metal unibody with a slim design.
If i would like to feel any cheap, fat plastic body i can buy a phone with a cheap plastic body.
I use xtremeskins UK sticker on top of back of my phone and plastic film screen protector as the one preinstalled has worn out. I have black carbon fibre version of the sticker with red accent on camera lens (which actually matches power button colour ) it looks cool and gives that extra grip.
Here is a link to website:
https://www.xtremeskins.co.uk/products/huawei-p10-skins?variant=36513341329
You can see for yourself how will your phone look like before you buy the actuall skin. The quality of a skin is amazing ,it's hardly add any bulk to the device and it does make it feel better in hand as well as add that extra wow factor when you pull out your phone from pocket.
I received my P10 on Thurs 07/12 and wanted to get a few opinions on whether i should remove the factory fitted screen protector prior to applying a glass screen protector or if i should just clean the factory fitted protector with the alcohol pads/swabs provided and stick the new glass screen protector on top?
Does the factory fitted protector reduce the clarity/sharpness of the screen in any way?
Would this be adequate:
https://www.amazon.co.uk/SUFUS-Prot...-4&keywords=huawei+p10+screen+protector+glass
Kind Regards
I'm using the original Huawei Flip cover and a full glass screen protector. As an electrician my hands aren't clean Everytime I grab my phone and sometimes I need to put some tools in the same pocket as the P10 is in.
But I hate the glass protector even it works very well. There's a black border around the whole protector and after a few month the protector doesn't fit perfectly anymore, it moved a bit to the left. The transparent part of the protector is a bit smaller than the screen and this is kind of annoying especially know it's moved.
I don't want to use a protector, but I think I need one. I don't want an ugly scratch on the screen.
Hi,
I removed the factory installed film in the screen and replaced it with a matte IQ Shield protector. It's great. It's not glass, but it has no reflections. Like most laptops.
Hello im Veronica and this is my first post owing this phone and im loving it! i bought a glass protection that come is curve design but it didnt fit well bubbles of air started to appear and i took it off
Have you tried the liquid protection ? i dont know the name of the product but is a liquid you put in the screen and it makes it hard
Please help me what do you use to protect it?
I use the uv Loca glue and glue on the curved tempered glass protectors on mine
Hi veronica. I own now an s8, but my previous phone was a galaxy s7 (the flat one), in which I had a tempered glass protector. But now, with the curved display of miss s8, the tempered glass I've found are not so great. I really don't recommend the liquid protection , that supposed nano tech solution. I've seen it, and its effects are practically none. U can't tell when u you've applied or not.
As the previous post says, the better solution is to take a tempered glass and UV glue between that and the gorilla glass, and dry it in the UV lamp. That way, u get a better protection, but need to try take out the air bubbles that may get in the process before dry.
I'm sorry if my English can't be excellent, because it's not my original language.
Greetings to u.
I also would be interested in mounting a tempered glass screen protector with a liquid adhesive and then drying it with a UV lamp. The end result looks very good, but I wonder if it does affect the screen of the phone. In case that I would like to remove the foil or replace it ... I do not know if the adhesive is "peaceful", if it leaves residual traces or I risk of having to change the touchscreen at the same time with the glass: D
I'd like to buy this: https://bit.ly/2SSQMZT (Aliexpress).
To be honest, the Spigen NeoFlex is the absolute best option in my opinion. I normally do not like these "Self-Healing" type but, it has been amazing, stays on all corners and I can continue to use my very light but very protective Spigen case as well. I normally do not like cases but the one I use is okay, especially since I have already shattered the front and rear of the phone once. Don't want to do it again.
I second this...
frozeninferno said:
To be honest, the Spigen NeoFlex is the absolute best option in my opinion. I normally do not like these "Self-Healing" type but, it has been amazing, stays on all corners and I can continue to use my very light but very protective Spigen case as well. I normally do not like cases but the one I use is okay, especially since I have already shattered the front and rear of the phone once. Don't want to do it again.
Click to expand...
Click to collapse
I've tried about 6 different tempered glass protectors, and all have either made it very difficult to pull down the top menu, or have gotten dust/lint behind the screen. Went to the Spigen NeoFlex 'film' and never looked back. In fact, I just ordered another set of them because I got polyurethane fingerprints on the screen while doing a wood railing. I had zero problems, it doesn't affect touch sensitivity. I will say that getting the sides to stay took a few minutes of work, but once stuck, it has stayed that way for 8 months so far. I paired it with a Spigen LiquidArmor case. I've dropped the phone onto my ceramic floors several times already and had no damage to the phone. I use wireless charging with no problems.