how to to wp7 bootloader needed files + miRom 7 radio 0321 as .tsw (if is not rename it to tg01wp_00.tsw)
read this first or if you have problems tnx avathar
1. make sure your battery are 100% FULLcharged!
2. copy flash the wm6.5 rom with 0321 radio to SD card PRG folder. Copy tg_ssdl.exe + tg_ssdl+.exe in the same folder
3. press on tg_ssdl+.exe to start the download
4. after 20 min. you have wm 6.5.x OS with 0321 radio.
5. Install tg downloader and the 32 bit driver. By first screen check all three rom variants
6. DownLoade Modus1: turn device off, pull battery out/in, then press and hold Camera + Power button (you get white led)
7. Start tg downloader. If you get a error window, press ok
8. connect your device + pc over usb
9. select over browse the file from wp7bootloader folder
10. Start download. on the 99% stay 1-2 min. PLEASE wait the 100% and the auto reboot
NOW you have the wp7bootloader and you able to flash wp7 rom
how to to flash wp7 rom if you allready on wp7 needed files
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
wp7 rom flash.zip
1. DownLoade Modus2: turn device off, pull battery out/in, then press and hold Camera + Power button (you get Blue led)
2. Install ZTEiT Common downloader and install the acer f1 driver
3. copy a wp7 rom, flash.bin in wp7OS_files
4. run ZTEiT Common downloader (select multi—download), browse to wp7OS_files folder and select him (check with advanced if the three files are set)
5. press START all and wait 20 - 28 min.
now you are on wp7 OS (if you like later to flash a other wp 7 rom, do the steps from howto to flash wp7 rom)
Now do this at end FIX 3G /RADIO SIGNAL
from wp7 to wm6 bootloader and flash back to 6.5 OS
ok i have managed it with few times (today) with succes: Charge your battery 100% full (few hours!)
(if is not possible to charge the battery in the phone read this)
needed TOOLS ( ZTEiT Common downloader, Tg downloader and Toshiba_TSW)
Prepare a 6.5 rom as .bin ROM with Toshiba_TSW browse to your exist 6.5 tsw rom, select Toshiba Tg01, press decode= you get a 6.5 bin ROM (or download my miROM7 Radio 0321as .bin)
1. TOOL ZTEiT Common downloader (get the 6.5 bootloader back- no OS)
1.1 turn the phone off
1.2 pull battery out/in, press Camera+Power button= Blue led go on ,you are on wp7 Download mode
1.3 Connect usb
1.4 run ZTEiT Common downloader (select multi- download) (to use you have to install the ACER F1 driver x86)
1.5 go to browse and select the folder
downgrade_WM6_boot.zip with the needed files
1.6 press advanced to check the selected files NPRG8650.hex, partition.mbn. dbl.mbn,fsbl.mbn,and osbl.mbn
1.7 press start all
after few seconds you got a white led, then close ZTEiT Common downloader, cut the usb connection
1.8 take the battery out (for few seconds) then press and hold the Camera and then the press and hold the Power button= white led go on
2 TOOL tg downloader (flash a 6.5 ROM)
2.1. run tg downloader (if get a error press ok)
2.2. connect your phone over usb- the programm recognize Toshiba download Port com
2.3. select browse your prepared 6.5 BIN ROM (if get a error press ok)
2.4. press Start Download, download starts led changing different colors. on 99% stay a while- but WAIT the 100% and it will reebot
NOW you on 6.5 OS
IT WORKS- BUT: IF the Download not start, try again step 1.8. and 2.1 -2.4
AND if the Download not start, log off/log on your pc and try again step 1.8. and 2.1 -2.4 (if is not possible to charge the battery in the phone read this)
DISCLAIMER
I will not take any responsibility for any damages caused directly or indirectly from using the software-package or the instructions. Read the instructions thoroughly and proceed carefully!
mirolg said:
from wp7 to wm6 bootloader and flash back to 6.5 OS
ok i have managed it with few times (today) with succes: Charge your battery 100% full (few hours!)
needed TOOLS ( ZTEiT Common downloader, Tg downloader)
Prepare a 6.5 rom as .bin ROM with Toshiba_TSW.zip browse to your exist 6.5 tsw rom, select Toshiba Tg01, press decode= you get a 6.5 bin ROM
1. TOOL ZTEiT Common downloader (get the 6.5 bootloader back- no OS)
1.1 turn the phone off
1.2 press Camera+Power button= Blue led go on ,you are on wp7 Download mode
1.3 Connect usb
1.4 run ZTEiT Common downloader (select multi- download)
1.5 go to browse and select the folder WM6boot with the needed files
1.6 press advanced to check the selected files NPRG8650.hex, partition.mbn. dbl.mbn,fsbl.mbn,and osbl.mbn
1.7 press start all
after few seconds you got a white led, then close ZTEiT Common downloader, cut the usb connection
1.8 take the battery out (for few seconds) then press and hold the Camera and then the press and hold the Power button= white led go on
2 TOOL tg downloader (flash a 6.5 ROM)
2.1. run tg downloader (if get a error press ok)
2.2. connect your phone over usb- the programm recognize Toshiba download Port com
2.3. select browse your prepared 6.5 BIN ROM (if get a error press ok)
2.4. press Start Download, download starts led changing different colors. on 99% stay a while- but WAIT the 100% and it will reebot
NOW you on 6.5 OS
IT WORKS- BUT: IF the Download not start, try again step 1.8. and 2.1 -2.4
AND if the Download not start, log off/log on your pc and try again step 1.8. and 2.1 -2.4
many thankst to qinwengui for his method/tools/files
Click to expand...
Click to collapse
Nice Tut., but qinwengui write only bootloader files *.mbn for *.bin file.
He not find other method upgrade etc.. then i dont understand why you write wrong info.
Nokser said:
Nice Tut., but qinwengui write only bootloader files *.mbn for *.bin file.
He not find other method upgrade etc.. then i dont understand why you write wrong info.
Click to expand...
Click to collapse
I not write a wrong info. exactly so i have do it 4 times, what files/info are wrong? in his folder WM6boot are five files: NPRG8650.hex, partition.mbn. dbl.mbn,fsbl.mbn,and osbl.mbn
you can download it and/or try it how write only bootloader files *.mbn for *.bin file?
example this line:
mirolg said:
for his method/tools/files
Click to expand...
Click to collapse
He not generate "NPRG8650.hex" file
Nokser said:
example this line:
He not generate "NPRG8650.hex" file
Click to expand...
Click to collapse
oh, sorry, your copyright and so ... I will ad microsoft, da_g, the half xda comunity and you ...
mirolg said:
oh, sorry, your copyright and so ... I will ad microsoft, da_g, the half xda comunity and you ...
Click to expand...
Click to collapse
Because I do not understand, why write some nonsense
I do not want you to thank me, but how can you thank someone who did not.
Believe me a lot of time spent on it all.
Nokser said:
Because I do not understand, why write some nonsense
I do not want you to thank me, but how can you thank someone who did not.
Believe me a lot of time spent on it all.
Click to expand...
Click to collapse
is not nonsense. I wanted to be fair to qinwengui;, I have this info + files from his thread:
qinwengui said:
3. wp7 to wm6 bootloader and flash 6.5 os
Camera+Power(Blue led) ,on Download mode,use ZTEiT Common downloader (select multi—download, not backup)
need file NPRG8650.hex,partition.mbn. dbl.mbn,fsbl.mbn,osbl.mbn
After finished 6.5boot,(Connect the pc Re),then,
Camera+Power Download mode,
dirver is Toshiba Download Port com,
If not, please replace,,
use TG-Downloader,flash the rom for 6.5...
file: http://cn.ziddu.com/download/625316/WM6boot.rar.html
demo video
http://cn.ziddu.com/download/625312/wp7-wm6.rar.html
TOOLS file: http://cn.ziddu.com/download/625313/TOOLS.rar.html
Click to expand...
Click to collapse
and he don´t write credits or copyright on this stuff- then i thank him .....
and who write partition.mbn. dbl.mbn,fsbl.mbn,and osbl.mbn and the other hounderts fils in your ROM
in your thread you don´t write the credits to other developer/manufacturer or what ...
....AND please don´t spam this IMPORTANT INFO THREAD
mirolg said:
and who write partition.mbn. dbl.mbn,fsbl.mbn,and osbl.mbn and the other hounderts fils in your ROM
Click to expand...
Click to collapse
no one ...
I build Factory Image file in parttsb.exe....
Back to 6,5 solved...
mirolg said:
from wp7 to wm6 bootloader and flash back to 6.5 OS
ok i have managed it with few times (today) with succes: Charge your battery 100% full (few hours!)
needed TOOLS ( ZTEiT Common downloader, Tg downloader)
Prepare a 6.5 rom as .bin ROM with Toshiba_TSW.zip browse to your exist 6.5 tsw rom, select Toshiba Tg01, press decode= you get a 6.5 bin ROM
1. TOOL ZTEiT Common downloader (get the 6.5 bootloader back- no OS)
1.1 turn the phone off
1.2 press Camera+Power button= Blue led go on ,you are on wp7 Download mode
1.3 Connect usb
1.4 run ZTEiT Common downloader (select multi- download)
1.5 go to browse and select the folder WM6boot with the needed files
1.6 press advanced to check the selected files NPRG8650.hex, partition.mbn. dbl.mbn,fsbl.mbn,and osbl.mbn
1.7 press start all
after few seconds you got a white led, then close ZTEiT Common downloader, cut the usb connection
1.8 take the battery out (for few seconds) then press and hold the Camera and then the press and hold the Power button= white led go on
2 TOOL tg downloader (flash a 6.5 ROM)
2.1. run tg downloader (if get a error press ok)
2.2. connect your phone over usb- the programm recognize Toshiba download Port com
2.3. select browse your prepared 6.5 BIN ROM (if get a error press ok)
2.4. press Start Download, download starts led changing different colors. on 99% stay a while- but WAIT the 100% and it will reebot
NOW you on 6.5 OS
IT WORKS- BUT: IF the Download not start, try again step 1.8. and 2.1 -2.4
AND if the Download not start, log off/log on your pc and try again step 1.8. and 2.1 -2.4
many thankst to qinwengui for his method, microsoft, da_g, the half xda comunity for developer tools and nokser .for.other files ...
Click to expand...
Click to collapse
Hi miro,
thanks for the info... I just back to 6,5. again. Very clear explanation.
I use your ROM´s but I must pass this phone to my wife, and I need a spanish version rom.Can you recommend me a spanish version. You might know some good Spanish version. There are many of good English one like yours, very fluide, but I must migrate to a Spanish one.
Thanks for your suppport and thanks again for the post.
Br
Patito
i'm in 1,8 state... white led!! but the phone stay in this state for only 5 sec... i think this is the battery...but the battery don't charging in this state... any idea??
Godric8 said:
i'm in 1,8 state... white led!! but the phone stay in this state for only 5 sec... i think this is the battery...but the battery don't charging in this state... any idea??
Click to expand...
Click to collapse
USB cable short charging
aeroflyluby said:
USB cable short charging
Click to expand...
Click to collapse
and what is it? or how can I build it?
---------- Post added at 06:26 PM ---------- Previous post was at 06:14 PM ----------
the phone does not charging because I think it goes in bootloadermode each 3 sec!LED changes from white to red each 3 sec
Godric8 said:
and what is it? or how can I build it?
---------- Post added at 06:26 PM ---------- Previous post was at 06:14 PM ----------
the phone does not charging because I think it goes in bootloadermode each 3 sec!LED changes from white to red each 3 sec
Click to expand...
Click to collapse
I will complain it about 5th time...
You cut USB cable, any type, unisolate red and black wires and put red to + and black to - in battery, wait about a minute holding it like this and check, if fails, repeat this cycle until you get battery working.
You can also check battery voltage with voltagemeter, 4.20 is 100%, 3.7 is about 60% and 3.0 is critical state assuming you damaged your cells.
Any overcharging or undercharging (more than 4.20 or less than 3.0) would make your battery funking explode...
ok i resolved the phone work perfect with 6.5 rom!! thanks all for help!!
PATITOPATITO said:
Hi miro,
thanks for the info... I just back to 6,5. again. Very clear explanation.
I use your ROM´s but I must pass this phone to my wife, and I need a spanish version rom.Can you recommend me a spanish version. You might know some good Spanish version. There are many of good English one like yours, very fluide, but I must migrate to a Spanish one.
Thanks for your suppport and thanks again for the post.
Br
Patito
Click to expand...
Click to collapse
very nice, patito
here my spanish rom miROM 10 SP
and here the ifo thread miROM10_ENG/GER/SPN
cheers, miro
Godric8 said:
i'm in 1,8 state... white led!! but the phone stay in this state for only 5 sec... i think this is the battery...but the battery don't charging in this state... any idea??
Click to expand...
Click to collapse
Just a tip ...Some might have same behavior.
when you open the tG downloader,The phone model its in the TG01W by defect. Change to TG01C. .You will see in ports option your phone conected to port . Them download.
If you leave it in tg01W option , most of the time the phone is detected but as soon as you try to update, it appears not found or port locked.
I hope this info can help you.
Br
---------- Post added at 08:33 PM ---------- Previous post was at 08:28 PM ----------
mirolg said:
very nice, patito
here my spanish rom miROM 10 SP
and here the ifo thread miROM10_ENG/GER/SPN
cheers, miro
Click to expand...
Click to collapse
Hi MIRO,
will download right now... Concerning The radio version in the file its 1800 already?.What radio version you can recomend me.
landscape scree ok with the tip in the post. Now all ok.
Thaks for the suppport
Patito
i did few time with tg01w and no problems at all
nikola92 said:
i did few time with tg01w and no problems at all
Click to expand...
Click to collapse
no matter.... normally you can select all three options ...... and if get error- ignore
PATITOPATITO said:
Just a tip ...Some might have same behavior.
when you open the tG downloader,The phone model its in the TG01W by defect. Change to TG01C. .You will see in ports option your phone conected to port . Them download.
If you leave it in tg01W option , most of the time the phone is detected but as soon as you try to update, it appears not found or port locked.
I hope this info can help you.
Br
---------- Post added at 08:33 PM ---------- Previous post was at 08:28 PM ----------
Hi MIRO,
will download right now... Concerning The radio version in the file its 1800 already?.What radio version you can recomend me.
landscape scree ok with the tip in the post. Now all ok.
Thaks for the suppport
Patito
Click to expand...
Click to collapse
yeeah, very good . I thik in the re-uploaded miROM 10 SPN ROM (tnx Pere) is my recomanded radio for your region, 1800 radio! 1600 are good foe east europa, 0300 and 0321 for UK
best regards, miro
mirolg said:
yeeah, very good . I thik in the re-uploaded miROM 10 SPN ROM (tnx Pere) is my recomanded radio for your region, 1800 radio! 1600 are good foe east europa, 0300 and 0321 for UK
best regards, miro
Click to expand...
Click to collapse
Hi
I tested today and good reception, so I wont change it.
Thanks my friend.
Br
Patito
---------- Post added at 08:06 PM ---------- Previous post was at 07:59 PM ----------
mirolg said:
no matter.... normally you can select all three options ...... and if get error- ignore
Click to expand...
Click to collapse
HiMIRO
In my case, No errors when you open the aplication and load the .bin with TG01W option, but if i press download, it appears locked and the process wont go further.
If i use option TG01 C . when you open the .bin ,the error appears, you ignore it and if i press dowload, the process goes normally.
I put the post just in case other people had the same behavior, couse they wont be able to go further (it was my case). They need to use just TG01C option
Br
Patito
Related
i just update rom Photon ROM 6.5 Standard Edition
http://forum.xda-developers.com/showthread.php?t=943396
now it hang only logo touch diamind 2.
how to do next?
please help me
Hi,
Remove SD Card, if any, and do a Hard Reset and see if that help.
Do let me know what is the result so that I can help you.
Cheers!!!
prabhat said:
Hi,
Remove SD Card, if any, and do a Hard Reset and see if that help.
Do let me know what is the result so that I can help you.
Cheers!!!
Click to expand...
Click to collapse
my phone Topa100 before update phone work well but i need change china language to english.
after update phone hang with logo touch diamond2
i try hard reset but not work for me.
Vichka said:
my phone Topa100 before update phone work well but i need change china language to english.
after update phone hang with logo touch diamond2
i try hard reset but not work for me.
Click to expand...
Click to collapse
Topa100: Looks like your device is NOT HTC Diamond2 or Topaz (Check WiKi - Check Model Numbers at Intro section)? If SO, you may have to try different ROM, as Photon ROM is for Topaz/HTC Diamond2 devices ONLY.
Let me know if I can help you in any way...
Cheers!!!
prabhat said:
Hi,
Remove SD Card, if any, and do a Hard Reset and see if that help.
Do let me know what is the result so that I can help you.
Cheers!!!
Click to expand...
Click to collapse
Dear prabhat,
Can you help see my case?
I flash a Diamond2 with official WM 6.1 ROM, after finish the phone stack on the tri-color screen, showing "Turbo SW/HW not match!". can any help help to save the Diamond2? Thank you.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Rom file name:RUU_Topaz_HKCSL_CHT_1.40.832.2_Radio_Sign_Topaz_61.25t.25.19_3.44.25.27_Ship.exe
Rom: 1.40.832.2
Radio: 3.44.25.27
Protocol: 61.25t.25.19
Some member teacher me try to reflash TopazSPLRelocker SPL133 first, but when I reflash "TopazSPLRelocker SPL133", the phone can change from tricolor screen to progress bar but the phone stuck at 0%, than after several minutes PC prompt [ERROR 262]. I follow the program to recovery the connection but still the same.
Also I appear same problem which stuck at 0% when flash any cooked rom, e.g. Photon ROM 6.5 and TiGeR Light Ver 1.
I also try flashing by using Storage Card by rename the cooked rom (.nbh) file to TOPAIMG.nbh, the result is same stuck on 0%.
I also try Advanced ROM Update Utility for TOUCH DIAMOND2/TOPAZ by Barin and "CustomRUU.exe" but still stuck at 0% and [ERROR 262], but it is success using official update exe (RUU_Topaz_HKCSL_CHT_1.40.832.2_Radio_Sign_Topaz_6 1.25t.25.19_3.44.25.27_Ship.exe).
Thank you.
Bun
hinbun said:
Dear prabhat,
Can you help see my case?
I flash a Diamond2 with official WM 6.1 ROM, after finish the phone stack on the tri-color screen, showing "Turbo SW/HW not match!". can any help help to save the Diamond2? Thank you.
Rom file name:RUU_Topaz_HKCSL_CHT_1.40.832.2_Radio_Sign_Topaz_61.25t.25.19_3.44.25.27_Ship.exe
Rom: 1.40.832.2
Radio: 3.44.25.27
Protocol: 61.25t.25.19
Some member teacher me try to reflash TopazSPLRelocker SPL133 first, but when I reflash "TopazSPLRelocker SPL133", the phone can change from tricolor screen to progress bar but the phone stuck at 0%, than after several minutes PC prompt [ERROR 262]. I follow the program to recovery the connection but still the same.
Also I appear same problem which stuck at 0% when flash any cooked rom, e.g. Photon ROM 6.5 and TiGeR Light Ver 1.
I also try flashing by using Storage Card by rename the cooked rom (.nbh) file to TOPAIMG.nbh, the result is same stuck on 0%.
I also try Advanced ROM Update Utility for TOUCH DIAMOND2/TOPAZ by Barin and "CustomRUU.exe" but still stuck at 0% and [ERROR 262], but it is success using official update exe (RUU_Topaz_HKCSL_CHT_1.40.832.2_Radio_Sign_Topaz_6 1.25t.25.19_3.44.25.27_Ship.exe).
Thank you.
Bun
Click to expand...
Click to collapse
Hi,
Looks like your device is locked for official rom till now so you are not able to install any custom ROM and it fails. As you did before, please do HARD-SPL again with step by step given in the same thread.
Make Sure you have Internet access on PC
Disable AV software if any
Connect the device to PC - ActiveSync/WMDC
Follow the "Instructions" in the thread. (Use Topaz-HardSPL_V5_09R6_CRT_183HSPL.zip)
PC may install some driver on first reboot of your device.
It should finish the task on your device and it should be ready.
Cheers!!!
prabhat said:
Hi,
Looks like your device is locked for official rom till now so you are not able to install any custom ROM and it fails. As you did before, please do HARD-SPL again with step by step given in the same thread.
Make Sure you have Internet access on PC
Disable AV software if any
Connect the device to PC - ActiveSync/WMDC
Follow the "Instructions" in the thread. (Use Topaz-HardSPL_V5_09R6_CRT_183HSPL.zip)
PC may install some driver on first reboot of your device.
It should finish the task on your device and it should be ready.
Cheers!!!
Click to expand...
Click to collapse
Thank you for your reply.
I CANNOT succeed do HARD-SPL. Any help? Thank you.
I follow every thing in the thread.
1. PC have Internet access.
2. PC install ActiveSync(XP)
3. PC installed driver on when first reboot the device.
4. Reboot PC before HSPL.
5. I use Topaz-HardSPL_V5_09R6_CRT_183HSPL.zip
6. I disable antivirus and windows firewall.
7. On the white part of tricolor screen it show "USB".
First I try automatic flash but show the following error:
I cannot not install the enablerapinew.cab because I cannot boot into WM.
Then I try Manual Flash, but also fail, the phone stuck at 0% and PC show ERROR [262], I followed the recovery procedure and try again it also fail the do HSPL.
hinbun said:
Thank you for your reply.
I CANNOT succeed do HARD-SPL. Any help? Thank you.
I follow every thing in the thread.
1. PC have Internet access.
2. PC install ActiveSync(XP)
3. PC installed driver on when first reboot the device.
4. Reboot PC before HSPL.
5. I use Topaz-HardSPL_V5_09R6_CRT_183HSPL.zip
6. I disable antivirus and windows firewall.
7. On the white part of tricolor screen it show "USB".
First I try automatic flash but show the following error:
I cannot not install the enablerapinew.cab because I cannot boot into WM.
Then I try Manual Flash, but also fail, the phone stuck at 0% and PC show ERROR [262], I followed the recovery procedure and try again it also fail the do HSPL.
Click to expand...
Click to collapse
try to reflash via SD-Card ! rename RUU_Signed.nbh file to TOPAIMG.NBH and put the file on the SD card
Hakim Rahman said:
try to reflash via SD-Card ! rename RUU_Signed.nbh file to TOPAIMG.NBH and put the file on the SD card
Click to expand...
Click to collapse
Thank you.
But probably not success because It is fail to use sd card to flash cook rom or radio. The phone always stuck at "Loading..." screen.
By the way, which "RUU_Signed.nbh" should I use? The Hard SPL is an exe. Thank you.
hinbun said:
Thank you.
But probably not success because It is fail to use sd card to flash cook rom or radio. The phone always stuck at "Loading..." screen.
By the way, which "RUU_Signed.nbh" should I use? The Hard SPL is an exe. Thank you.
Click to expand...
Click to collapse
this RUU file that can be you use Hard-SPL 1.83.OliNex
Hakim Rahman said:
this RUU file that can be you use Hard-SPL 1.83.OliNex
Click to expand...
Click to collapse
Dear Rahman,
I also try flashing Hard-SPL 1.83.OliNex by using Storage Card by rename the to to TOPAIMG.nbh, but the phone keep stuck on "Loading..." screen. Thank you.
Bun
Just a wild guess... try removing your SIM and SD Card and re-try.
Cheers!!!
Hakim Rahman said:
this RUU file that can be you use Hard-SPL 1.83.OliNex
Click to expand...
Click to collapse
Dear Rahman,
it is also fail to use SD card to do HSPL!! Ths phone was stuck on "Loading" screen.
Another other method? Thank you
---------- Post added at 09:35 AM ---------- Previous post was at 09:33 AM ----------
prabhat said:
Just a wild guess... try removing your SIM and SD Card and re-try.
Cheers!!!
Click to expand...
Click to collapse
Dear prabhat,
I try removed the SIM and SD Card its also fail!! Stuck on "Loading..." screen. Any method to save my phone? Thank you
Your Problem will be 100% solve. I tested.
Vichka said:
my phone Topa100 before update phone work well but i need change china language to english.
after update phone hang with logo touch diamond2
i try hard reset but not work for me.
Click to expand...
Click to collapse
Your Problem will be 100% solve. I tested.
You Need to update your Radio version. Download from Here....
my tg01 wont start after win 7 .....and no charge .....what can i do?.....it's my favorit phone ......... when i want to start him ..he just blinking the red led ...and nothing more ...(( sorry for bad english ,im from romania
crosz7 said:
my tg01 wont start after win 7 .....and no charge .....what can i do?.....it's my favorit phone ......... when i want to start him ..he just blinking the red led ...and nothing more ...(( sorry for bad english ,im from romania
Click to expand...
Click to collapse
you must charge battery.
Connect via USB, and wait... when u phone start, write him in Bootloader Menu(+- Volume), select USBfnSerial, save, and wait for green LED
well.....when i wont to start him i se green led but black screen ...and vol+.- plus power dont work ...just camera and power for blue led and black screen
Hello
I had exactly the same problem and after 3 days of trying different things managed to get back to WM 6.5
I believe black screen and blue LED means you are in Bootloader mode, I followed this from 3.
wp7 can get back to wm6 now £¬Cheer
The test is successful
TG01 and T01A
very important
you need backup your EFS2.BIN£¨imei£©¡£¡£
Demo Video for writer All bootloader, os, falsh back
1/wm6 to wp7 bootloader
Short pin 1,3 or 0321rom Camera+Power ,on Download mode,use TG-Downloader
file tg01 wm6 Update wp7 Bootloader.bin, no os
http://cn.ziddu.com/download/625263/wp7boot.rar.html
demo video
http://cn.ziddu.com/download/625310/...7boot.rar.html
2.flash wp7 os
Camera+Power(Blue led) ,on Download mode,setup acer f1 driver ,use ZTEiT Common downloader(select multi—download, not backup)
or other tool(qpst / acer euu etc..)
need file flash.bin(os.nb) ,NPRG8650.hex,partition.mbn.
file: http://cn.ziddu.com/download/625315/WP7os.rar.html
demo video:
http://cn.ziddu.com/download/625311/flashos.rar.html
3. wp7 to wm6 bootloader and flash 6.5 os
Camera+Power(Blue led) ,on Download mode,use ZTEiT Common downloader (select multi—download, not backup)
need file NPRG8650.hex,partition.mbn. dbl.mbn,fsbl.mbn,osbl.mbn
After finished 6.5boot,(Connect the pc Re),then,
Camera+Power Download mode,
dirver is Toshiba Download Port com,
If not, please replace,,
use TG-Downloader,flash the rom for 6.5...
file: http://cn.ziddu.com/download/625316/WM6boot.rar.html
demo video
http://cn.ziddu.com/download/625312/wp7-wm6.rar.html
TOOLS file: http://cn.ziddu.com/download/625313/TOOLS.rar.html
If you want to be able to flash other ROMS from your SD card you will need to convert any tsw file to a bin file. Follow this and you should be ok. If not I'm willing to sort it out for you but you will need to send me your phone. I live in the UK
and qpst wont work he sey: qpst can't connect vaio atlas server //my laptop is a vaio
men help me i cant't instal botloader ......i flashed the phone and win7 dont work ...and i want to reinstal botloader with tg downloader and i cant what can i do ?
crosz7 said:
men help me i cant't instal botloader ......i flashed the phone and win7 dont work ...and i want to reinstal botloader with tg downloader and i cant what can i do ?
Click to expand...
Click to collapse
NOT WITH TG DOWNLOADER! YOU NEED THIS STEPS BEFORE:
to get the 6.5.x Bootloader:
go in bootloader mode Camera+Power (Blue led) ,on Download mode,use ZTEiT Common downloader (select multi—download, not backup)
need file NPRG8650.hex,partition.mbn. dbl.mbn,fsbl.mbn,osbl.mbn
After finished you have the 6.5 bootloader. NOW charge your battery 5-6 hours full!!!
Prepare a 6.5.x .TSW ROM as .BIN ROM
TSW TOOLS
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Toshiba_TSW.zip - encoder/decoder for tsw files / bin files
tnx http://cotulla.pp.ru/Misc.html
- browse to your toshiba ROM .tsw, then select Toshiba TG01 and you get a toshiba ROMas .bin file- ready to flash with TG Downloader
use/install TG-Downloader + Toshiba drivers. bring with Camera+Power to Download mode use TG-Downloader to flash the 6.5 BIN ROM
the tools + files + tut you find here: toshiba tg01 WP7 ROM
mirolg said:
NOT WITH TG DOWNLOADER! YOU NEED THIS STEPS BEFORE:
to get the 6.5.x Bootloader:
go in bootloader mode Camera+Power (Blue led) ,on Download mode,use ZTEiT Common downloader (select multi—download, not backup)
need file NPRG8650.hex,partition.mbn. dbl.mbn,fsbl.mbn,osbl.mbn
After finished you have the 6.5 bootloader. NOW charge your battery 5-6 hours full!!!
Prepare a 6.5.x .TSW ROM as .BIN ROM
TSW TOOLS
Toshiba_TSW.zip - encoder/decoder for tsw files / bin files
tnx http://cotulla.pp.ru/Misc.html
- browse to your toshiba ROM .tsw, then select Toshiba TG01 and you get a toshiba ROMas .bin file- ready to flash with TG Downloader
use/install TG-Downloader + Toshiba drivers. bring with Camera+Power to Download mode use TG-Downloader to flash the 6.5 BIN ROM
the tools + files + tut you find here: toshiba tg01 WP7 ROM
Click to expand...
Click to collapse
Hi Mirolg,
What do you do when ZTEiT Common downloader doesn't detect your phone? I tried qpst but it doen'st detect either. The computer detects Incorporated Qualcomm CDMA Technologies MSM pilot from the phone but that's it.
Thanks
jonslayer0 said:
Hi Mirolg,
What do you do when ZTEiT Common downloader doesn't detect your phone? I tried qpst but it doen'st detect either. The computer detects Incorporated Qualcomm CDMA Technologies MSM pilot from the phone but that's it.
Thanks
Click to expand...
Click to collapse
before I install ZTEiT Common downloader, I install the ACER Driver too- then detect the device ....
mirolg said:
before I install ZTEiT Common downloader, I install the ACER Driver too- then detect the device ....
Click to expand...
Click to collapse
Thanks Mirolg it worked. But I had to do it with a round about method (lol):
-I have XP 32 installed on a virtual box cause tg downloader wasn't working with seven,
-BUT the acer drivers wouldn't install on XP so I had to install them and common downloader on seven, and common downloader detected my phone.
-Then I flashed the wm6 bootloader on seven,
-switched to XP to flash 321 rom. A real mess I tell you.
-Now I'm going to wait till my phone is fully charged and try to flash to wp7.
Again thanks a lot Mirolg
jonslayer0 said:
Thanks Mirolg it worked. But I had to do it with a round about method (lol):
-I have XP 32 installed on a virtual box cause tg downloader wasn't working with seven,
-BUT the acer drivers wouldn't install on XP so I had to install them and common downloader on seven, and common downloader detected my phone.
-Then I flashed the wm6 bootloader on seven,
-switched to XP to flash 321 rom. A real mess I tell you.
-Now I'm going to wait till my phone is fully charged and try to flash to wp7.
Again thanks a lot Mirolg
Click to expand...
Click to collapse
uuuoo what for a confused but cool solution - RESPECT!
THX for everyone ....my tg01 is work ...sory for bad english
Maybe olly could revive his device by this method?
crosz7 said:
THX for everyone ....my tg01 is work ...sory for bad english
Click to expand...
Click to collapse
tnx for the good news - but how exactly have you get it works? please be
collegial an explain it a little bit more- maybe it will helps other .....
men now i have a major problem
i instalated my windows 7 and i dont like it and i instalated bot loader for win 6.5 using comon downloader and every thing goes ok ....and now i must instal win 6.5 bin with tg downloader but i can't he stock on 20%
yes it does crash just keep forsing it to close and re open tg downloader it took me about 4 times before it started
to work haha
I've got the same problem.
Followed the qinwengui guide and downloaded all the files from that thread.
I can load the boot loader and then use Common Downloader to load the WP7 image.
It appears to complete but WP7 doesn't boot.
I can then put the phone into bootloader mode and go back to 6.5, no problem.
Done this 2 or 3 times with the same result - no boot.
My phone is currently on charge with the 321 6.5 image, awaiting the next attempt...
The WP7 package from the qinwengui thread only contains 3 files:
flash.bin
NPRG8650.hex
partition.mbn
Nokser's threads mention the following files:
1.dbl.mbn
2.fsbl.mbn
3.osbl.mbn
4.amss.mbn
5.apps.mbn – this file you must uncheck
6.appsboot.mbn
7.flash.bin
8.dsp1.mbn
which I don't have and can't find
I assume the partition.mbn contains the appropriate information but I'd still like to try with the other files as this may be the issue wih my phone.
Also I can't find tsunagi_ffu.exe - does anyone have a link as I'd like to try that method as well.
Thanks.
Please help me!
I had to downgrade to 6.5 but with common after flash downloader wm6 boot files can not flash the system! with tgdownloader I do not recognize the phone even if it is in downloader mode!
Edit:
The process is blocked in Phone state beign confirmed 20%
Edit:
I try to refresh the boot but nope... error: DL.Nop fail
---------- Post added at 01:53 AM ---------- Previous post was at 01:10 AM ----------
Originally Posted by PATITOPATITO View Post
I have the BATT charged... Now what should i do.... If i put the tg download with a 6,5 bin, the aplicationsais locked...xd.
If i try to put bootolade 6,5 with common downloader, the phone is detected and stops at 20%...the light goes to blue...but nothing happends.
Any idea?
idem... do you have solved?
I reloaded and now the phone does not go into bootloader .. the light stays red... if i press camera + power the phone go into bootloader for 5 sec...
With other battery the phone stay in bootloader mode but common downloader and tgdownloader doesn't start the flash... any idea?? help pls
i Try with qpst but the phone change the color of led... Now the light stays red even with this battery...! i think my battery don't charging
First charge your batt. I have made a usb charger for the batt with the help of this site method.
USB CHARGER.
Cut the head of a usb you had (a spare one you have)Normally they have 5 wires inside the cable.
Put the red wire to + of the batt , and black to the - (both are marked in the batt). Do not put ANYTHING in the middle pole of batt or it will be damage.
I sticked the wires with fix type. Very easy.
Leave charging a couple of hrs.
No that you have the batt charge, put it on the phone and see thats happend for sure.
Br I hope this tip helps.
Patito
PATITOPATITO said:
First charge your batt. I have made a usb charger for the batt with the help of this site method.
USB CHARGER.
Cut the head of a usb you had (a spare one you have)Normally they have 5 wires inside the cable.
Put the red wire to + of the batt , and black to the - (both are marked in the batt). Do not put ANYTHING in the middle pole of batt or it will be damage.
I sticked the wires with fix type. Very easy.
Leave charging a couple of hrs.
No that you have the batt charge, put it on the phone and see thats happend for sure.
Br I hope this tip helps.
Patito
Click to expand...
Click to collapse
You know that overcharging battery may cause it to explode really? Couple of hours is TOO MUCH.
hello guys;
i am in a bit of trouble on win7 x64.
i am trying to flash my tablet with a new rom via livesuitepack 1.7 but the driver which comes with the livesuite doesn't do the trick.
the complete id of the device in device manager is "USB\VID_1F3A&PID_EFE8". and i am wondering if anyone has or know where could i find the suitable driver for that id.
thanks a lot
xgeek
xgeek.cub said:
hello guys;
i am in a bit of trouble on win7 x64.
i am trying to flash my tablet with a new rom via livesuitepack 1.7 but the driver which comes with the livesuite doesn't do the trick.
the complete id of the device in device manager is "USB\VID_1F3A&PID_EFE8". and i am wondering if anyone has or know where could i find the suitable driver for that id.
thanks a lot
xgeek
Click to expand...
Click to collapse
I'm curious what tablet you have and if you'd have any progress. I recently got a Craig CMP741e and was trying to see if I could get into the bootloader. Now it's stuck with a blank screen and shows the same device when plugged in. Seems to be unresponsive, and it looks like it won't boot up normally unless I take it apart and cut power or let the battery drain.
Hello,
It seems that you messed up your bootloader.
The problem you replied to was about the Freelander PD60 (a chinese tablet) 's device driver. The driver to use and flash a rom to it.
I suggest you go and find your latest rom for your device and flash your tablet with it.
Sent from my SXZ-PDX0-03 using Tapatalk HD
Your device should be off and you should press volume - and connect your tablet to the pc.
Install the driver and use live suite to flash new rom into.
If you need any specific let me know.
If the is a driver issue, let me know to give you a link for my driver. If the hardware id is the same you could use that.
Sent from my SXZ-PDX0-03 using Tapatalk HD
Thanks
I'm facing exactly the same issue with Windows 8 (x64) although it worked with Windows 7.
Gesendet von meinem HTC Wildfire S A510e mit Tapatalk 4 BETA
djolivier said:
I'm facing exactly the same issue with Windows 8 (x64) although it worked with Windows 7.
Gesendet von meinem HTC Wildfire S A510e mit Tapatalk 4 BETA
Click to expand...
Click to collapse
As far as I know there is no driver for win8 64bit edition. But there may be a driver for that if you could find LiveSuit 1.9 from your vendor.
you are the one
xgeek.cub said:
Your device should be off and you should press volume - and connect your tablet to the pc.
Install the driver and use live suite to flash new rom into.
Sent from my SXZ-PDX0-03 using Tapatalk HD
Click to expand...
Click to collapse
DUDE DUDE DUEEEEEEEEEEEEEEEE . God bless you soooo hard. you saved my tablet after 4 days hard research in google, to find a solution .How to thank you ! i give you 5 stars.
I could not find any solution to get into Fastboot & boot loader, and the worst was i did install CMBook 10 and i got stuck on "encryption unsuccess" . no access to "Clock Work"
NOW I AM IN .... thanks alot for your solution.
driver request
xgeek.cub said:
Your device should be off and you should press volume - and connect your tablet to the pc.
Install the driver and use live suite to flash new rom into.
If you need any specific let me know.
If the is a driver issue, let me know to give you a link for my driver. If the hardware id is the same you could use that.
Sent from my SXZ-PDX0-03 using Tapatalk HD
Click to expand...
Click to collapse
could you please provide that same driver, i effed up my bootloader to
tablet AT792HC (great tab but support is close to none)
also i am trying to find a custom recovery that might worth with this one, it has an allwinner a20 chipset with dual Mali 400 gpu
i would greatly apreciate any help
reply
seventh_burn said:
could you please provide that same driver, i effed up my bootloader to
tablet AT792HC (great tab but support is close to none)
also i am trying to find a custom recovery that might worth with this one, it has an allwinner a20 chipset with dual Mali 400 gpu
i would greatly apreciate any help
Click to expand...
Click to collapse
Hello, no worries, Now you options are not limited, you can even use suasage script instead of Livesuit. But I recommend livesuite. The latest version that I know is livesuit 1.11 and you can get it from softpedia. But it would be better if you coukd get the kates version of livesuit for your own tablet. From the manufacturer website.
I will post a series of livesuits here also for all of us.
In terms of ROM, ask aroud. You could found yours or relatively similar Roms. But bebcareful don't flase just any rom. That may damage you device.
now that was fast o.o
xgeek.cub said:
Hello, no worries, Now you options are not limited, you can even use suasage script instead of Livesuit. But I recommend livesuite. The latest version that I know is livesuit 1.11 and you can get it from softpedia. But it would be better if you coukd get the kates version of livesuit for your own tablet. From the manufacturer website.
I will post a series of livesuits here also for all of us.
In terms of ROM, ask aroud. You could found yours or relatively similar Roms. But bebcareful don't flase just any rom. That may damage you device.
Click to expand...
Click to collapse
right now i just want to get the device running again hahahaha (and if luck may see fit.. root the damn thing LOL)
think you could help me out.? i won my self a MASIVE fail trying to mess with a device i just recently purchased T.T
reply
seventh_burn said:
right now i just want to get the device running again hahahaha (and if luck may see fit.. root the damn thing LOL)
think you could help me out.? i won my self a MASIVE fail trying to mess with a device i just recently purchased T.T
Click to expand...
Click to collapse
Sure, give me your device exact specs like make and model , inch, memory, hard, cpu and gpu ... , and I give you list of Roms if I found any.
Then after you booted your device, I tell you how to root it.
Don't worry
device info
xgeek.cub said:
Sure, give me your device exact specs like make and model , inch, memory, hard, cpu and gpu ... , and I give you list of Roms if I found any.
Then after you booted your device, I tell you how to root it.
Don't worry
Click to expand...
Click to collapse
Aikun AT792HC
Allwinner dual Core Arm Cortex A7 1.2 ghz
ram 1gb ddr3
flash memory 8gb
screentype capacitive multitouch
screensize 7.85inch panel 1024x768 pixels
camera front 0.3 mpx back 2.0mp
cant get it past android screen
although got the driver running ( i was thinking of trying to flash a custom recovery to see if i can solve the issue but no idea as to where to look, this since finding a stock rom for this is very unlikely)
Forget about any custom job right now, when we flash your device again . And when it boots I will tell you how to go for custom rom as you have that option and they are afew custom roms out there. Again they should match your device.
Wait for next post
gpu info update
seventh_burn said:
Aikun AT792HC
Allwinner dual Core Arm Cortex A7 1.2 ghz
ram 1gb ddr3
flash memory 8gb
screentype capacitive multitouch
screensize 7.85inch panel 1024x768 pixels
camera front 0.3 mpx back 2.0mp
cant get it past android screen
although got the driver running ( i was thinking of trying to flash a custom recovery to see if i can solve the issue but no idea as to where to look, this since finding a stock rom for this is very unlikely)
Click to expand...
Click to collapse
pardon, GPU if im not mistaken it has mali 400 (dual stated but not confirmed)
Firmware in case its needed
seventh_burn said:
pardon, GPU if im not mistaken it has mali 400 (dual stated but not confirmed)
Click to expand...
Click to collapse
http://aikun.com.mx/support/AT792HC/ here is the link to the firmware and phoenixsuite that was used to restore my device, now all im missing is a good rom for it
thank you for your awesome support and if you could point me to a good rom and recovery i would be very thankfull!
Firmware = ROM
First of all hello;
You are so lucky that you found your (STOCK, Native, Factory ...) ROM or Firmware.
For your and all the other chinese tables the ROM is the file with .img extension.
http://aikun.com.mx/support/AT792HC/MVTA-007.img
As it seems Aikun prefers the PhoenixSuit For Flashing ROM. But no worries you still could use LiveSuit if you want to.
So first i will explain the process with Phoenix Suit. Then I will EXPLAIN THE SAME PROCESS with LiveSuit ( YOU SHOULD TRY ONLY ONE of them).
I urgently recommend that you use a Fresh Window Installation. (Either 7 or 8 or XP). if you previously installed android ADB driver or other android related drivers, You may run into trouble. At least remove all the android related drivers and softwares and restart you computer.
1. Install PhoenixSuit. It will install the android USB Driver too. If it asks you that the driver has no valid signature you should press install it any way. IF not do the following:
If you encounter the driver problem like thee image below (Google android driver NOT INSTALLED) or you see your android device with red(x) or yellow (!) on it in windows device manager. Follow these Steps.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(This problem happened in windows 8 64bit)
Press end and continue installation of PhoenixSuit .
After that press the update to see if there is a new version available. if yes download and install the new version too.
Again in installation you receive the error message again , dont worry .
Press end and continue installation of PhoenixSuit .
After finish the installation , go to the google site and download the Android SDK ( choose the correct version x32 or x64 for your system ).
Ok now run the android sdk in your computer after finish you can see what have installed.
Go to folder of android sdk and find the USB driver folder. (The Google USB Driver is located in <sdk>\extras\google\usb_driver\.)
2. From this folder COPY all files EXCEPT the "source.properties"
3. Now go to the PhoenixSuit folder C:\Program Files (x86)\AllWinnertech\PhoenixSuit. [boot disk for me are C:]
Go to folder Drivers ---> C:\Program Files (x86)\AllWinnertech\PhoenixSuit\Drivers .
Now enter to folder ADB_Driver --> C:\Program Files (x86)\AllWinnertech\PhoenixSuit\Drivers\ADB_Driver
And press Paste and REPLACE the contents in the folder (Paste the contents previously copied in step 2 )
4. Go back in folder C:\Program Files (x86)\AllWinnertech\PhoenixSuit .
5. find the file "PhoenixDrvInstall.exe"
6. Now run ( as administrator ) the "PhoenixDrvInstall.exe"
AND VOILA
HowTo install ROM:
FIRST POWER OFF YOU TABLET
1. press Volume -- key and then connect the tablet to PC via usb cable.
2. If you asked to install the driver you do. If you asked that the driver has not been SIGNED you press install it anyway. (or something like that)
3. After the driver(s) is installed; disconnect your table from the PC.
4. Press volume + key and then connect the tablet to PC via usb cable. If you are asked to install the driver again you do
5. Go to PhoenixSuit and select the .img file and press ok to install the ROM.
6. Accept the mandatory Foramt.
epic win!
xgeek.cub said:
First of all hello;
You are so lucky that you found your (STOCK, Native, Factory ...) ROM or Firmware.
For your and all the other chinese tables the ROM is the file with .img extension.
http://aikun.com.mx/support/AT792HC/MVTA-007.img
As it seems Aikun prefers the PhoenixSuit For Flashing ROM. But no worries you still could use LiveSuit if you want to.
So first i will explain the process with Phoenix Suit. Then I will EXPLAIN THE SAME PROCESS with LiveSuit ( YOU SHOULD TRY ONLY ONE of them).
I urgently recommend that you use a Fresh Window Installation. (Either 7 or 8 or XP). if you previously installed android ADB driver or other android related drivers, You may run into trouble. At least remove all the android related drivers and softwares and restart you computer.
1. Install PhoenixSuit. It will install the android USB Driver too. If it asks you that the driver has no valid signature you should press install it any way. IF not do the following:
If you encounter the driver problem like thee image below (Google android driver NOT INSTALLED) or you see your android device with red(x) or yellow (!) on it in windows device manager. Follow these Steps.
(This problem happened in windows 8 64bit)
Press end and continue installation of PhoenixSuit .
After that press the update to see if there is a new version available. if yes download and install the new version too.
Again in installation you receive the error message again , dont worry .
Press end and continue installation of PhoenixSuit .
After finish the installation , go to the google site and download the Android SDK ( choose the correct version x32 or x64 for your system ).
Ok now run the android sdk in your computer after finish you can see what have installed.
Go to folder of android sdk and find the USB driver folder. (The Google USB Driver is located in <sdk>\extras\google\usb_driver\.)
2. From this folder COPY all files EXCEPT the "source.properties"
3. Now go to the PhoenixSuit folder C:\Program Files (x86)\AllWinnertech\PhoenixSuit. [boot disk for me are C:]
Go to folder Drivers ---> C:\Program Files (x86)\AllWinnertech\PhoenixSuit\Drivers .
Now enter to folder ADB_Driver --> C:\Program Files (x86)\AllWinnertech\PhoenixSuit\Drivers\ADB_Driver
And press Paste and REPLACE the contents in the folder (Paste the contents previously copied in step 2 )
4. Go back in folder C:\Program Files (x86)\AllWinnertech\PhoenixSuit .
5. find the file "PhoenixDrvInstall.exe"
6. Now run ( as administrator ) the "PhoenixDrvInstall.exe"
AND VOILA
HowTo install ROM:
FIRST POWER OFF YOU TABLET
1. press Volume -- key and then connect the tablet to PC via usb cable.
2. If you asked to install the driver you do. If you asked that the driver has not been SIGNED you press install it anyway. (or something like that)
3. After the driver(s) is installed; disconnect your table from the PC.
4. Press volume + key and then connect the tablet to PC via usb cable. If you are asked to install the driver again you do
5. Go to PhoenixSuit and select the .img file and press ok to install the ROM.
6. Accept the mandatory Foramt.
Click to expand...
Click to collapse
This won so hard that chuck norris gave it kudos... Now all im missing is a custom rom so i can take advantage of this tablet's specs T.T
Flashing tablet by the use of LIVESUIT
DO ONE OF 2 OPTIONS LIVESUIT OR THE POST BEFORE.
First get the latest version of livesuit from XDA.
Then unpack it.
Click on the livesuit icon (blue and white cubic icon). It will automatically goes to system tray.
By doing so it installs the basic driver package that comes with it.
Now shutdown your tablet
Attach one end of the usb cable to it
Press volume - and hold
Then connect another end of usb cable to the PC.
The window will pop up asking for the location of the device driver.
Address it to where you unpack LiveSuit.
In the Livesuit directory there is a folder named driver. Choose it. (Inside is seprate set of drivers for 32 and 64 bit drivers)
Now click install driver.
Disconnect the usb cable.
Press volume + hold it and connect to PC.
Now when the driver installed, livesuit starts the flashing process by automatically asking for ". img" file. Choose it
You are asked to format the driver. Press yes.
Do not disconnect the usb cable while the process is going on.
For now I dont think any custom rom is available for your device but as the time goes by this will change.
First try to root this rom and go from there.
The next step would be platinum packup pro
Then dolphin browser and a MX video player pro
I tried to flash latest rom from Asus website to my new Zenfone C because it had a weird issue, it came the user interface in taiwanesse, but when trying to change to english, it stayed in taiwanesse, so I wasnt able to setup it in first place.
Then, it came to my mind to flash the latest rom, and I used this guide in absence of a Zenfone C guide for flashing:
http://en.zenfoneasus.com/zenfone-recovering-returning-stock-rom-downgrade-clean-update-guide/
I did all the steps listed there first, and then tried the steps but with the red marked steps, flashing the dnx and ifwi also, no result.
The problem is that now im stuck in a bootloop, and cant advance from there, the Asus logo stays there forever.
What happened during flashing is this:
When I sideloaded the update.zip containing latest rom from Asus website, it said:
-Installing update
-Device image SKU: ww
OTA image SKU: WW
and suddenly after that it restarted, showed a huge Intel Inside logo that I never saw and then went to the dead android image. After waiting a while, the phone restarts, this time only showing the Asus logo with the Intel Inside logo beneath it (not the Intel Inside logo only that I mentioned earlier), and stays there forever.
I dont know what else to do, I dont know if Im doing something wrong.
Were you ever able to fix the problem?
No, until now, no
Sent from my Nexus 5 using Tapatalk
Solved!!!
Hey Spartan!
I was searching online about nexus 5 to buy one but I found something else randomly in an Indonesian blog and was able fix my phone! Hardly took about 15 minutes
I will be posting the solution soon... I hope you are still in need?
kkdevta said:
Hey Spartan!
I was searching online about nexus 5 to buy one but I found something else randomly in an Indonesian blog and was able fix my phone! Hardly took about 15 minutes
I will be posting the solution soon... I hope you are still in need?
Click to expand...
Click to collapse
I still need the fix man, I will really appreciate the posting of the solution! thanks in advance!
Sent from my Nexus 5 using Tapatalk
The Fix!
First Download: -
USB Drivers: http://www.asus.com/in/Phones/ZenFone_C_ZC451CG/HelpDesk_Download/
Asus Flash Tool v1.0.0.11: https://drive.google.com/file/d/0B7cZB2l2IKlKMENKUWlVaHJ3ZHM/view
Signed Rom zip image: https://drive.google.com/file/d/0B__oiYlSY-brdHFWMy1OWXNrajg/view
The Process: -
Get your phone to boot into fastboot mode by pressing [vol -] button and power button simultaneously for few seconds.
Connect to your PC and install USB drivers if not done already. The phone should show up as an "ASUS Android Composite ADB Interface" in the Device Manager.
Now, open ASUS Flash Tool :-
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It should detect your phone with serial number and blue orb in front of it.
Select your phone model i.e. ZC451CG
Choose if you want to wipe data or not. I chose "Wipe Data" since I had everything backedup on asus web storage.
Click that box icon and browse for the signed zip image file you downloaded earlier.
Select your device on the ASUS flash Tool by clicking on the serial number like shown in the picture below.
( It had me scratch my head after one failed attempt because I didn't select it the first time! :silly
Click on the green start button, be patient, stay calm and cross your fingers. This could take 10-20minutes or so.:fingers-crossed:
If everything went well your phone should bootup to the welcome screen like the day 1 you got it.
Now, the zip image is quite old so after the initial setup the phone would prompt you with lots of system and app updates. Go with it and enjoy! :victory:
Lastly, don't be shy of pressing that " :good:Thanks! " button if this post helped you.
Thanks man, I will try tonight. Do you know if this works under Windows 8.1 64bits??. I see the screenshots are from windows 7.
Spartan Legionnaire said:
Thanks man, I will try tonight. Do you know if this works under Windows 8.1 64bits??. I see the screenshots are from windows 7.
Click to expand...
Click to collapse
Hopefully it should, I did it on a Windows 7 Professional 64 bit machine.
The USB drivers you download has Windows 8 drivers in it. I think that's all that is needed.
Yeah, I will try it then, and report back, thanks again.
Sent from my Nexus 5 using Tapatalk
kkdevta said:
First Download: -
USB Drivers: http://www.asus.com/in/Phones/ZenFone_C_ZC451CG/HelpDesk_Download/
Asus Flash Tool v1.0.0.11: https://drive.google.com/file/d/0B7cZB2l2IKlKMENKUWlVaHJ3ZHM/view
Signed Rom zip image: https://drive.google.com/file/d/0B__oiYlSY-brdHFWMy1OWXNrajg/view
The Process: -
Get your phone to boot into fastboot mode by pressing [vol -] button and power button simultaneously for few seconds.
Connect to your PC and install USB drivers if not done already. The phone should show up as an "ASUS Android Composite ADB Interface" in the Device Manager.
Now, open ASUS Flash Tool :-
It should detect your phone with serial number and blue orb in front of it.
Select your phone model i.e. ZC451CG
Choose if you want to wipe data or not. I chose "Wipe Data" since I had everything backedup on asus web storage.
Click that box icon and browse for the signed zip image file you downloaded earlier.
Select your device on the ASUS flash Tool by clicking on the serial number like shown in the picture below.
( It had me scratch my head after one failed attempt because I didn't select it the first time! :silly
Click on the green start button, be patient, stay calm and cross your fingers. This could take 10-20minutes or so.:fingers-crossed:
If everything went well your phone should bootup to the welcome screen like the day 1 you got it.
Now, the zip image is quite old so after the initial setup the phone would prompt you with lots of system and app updates. Go with it and enjoy! :victory:
Lastly, don't be shy of pressing that " :good:Thanks! " button if this post helped you.
Click to expand...
Click to collapse
IT WORKEEEED!!!! I dont know how to thank you man!. Thank you so much, I was going to give up on this device!. Its working really well.
The only thing I came into trouble, was to install the USB drivers included in the Asus Flash Tool. I did the following (on Windows 8.1 64bits):
I disabled driver signature check first on windows.
I went to the USB drivers folder inside the ASUS Flash tool folder on Program Files.
I went here C:\Program Files (x86)\ASUS\ASUS Flash Tool\Driver\USBDriverInstaller\devcon\x64
On that folder, there is a program called devcon.exe, right click on it, and select properties.
On compatibility tab select Run as Administrator, click ok.
After this, reinstall USB drivers by going to C:\Program Files (x86)\ASUS\ASUS Flash Tool\Driver\USBDriverInstaller and here execute install_drivers.bat
Thats it, the phone now should be recognized by the Asus Flash Tool.
I always failed when downloading Signed Rom zip image.. Someone please provide mirror... Thanks
Tjecing said:
I always failed when downloading Signed Rom zip image.. Someone please provide mirror... Thanks
Click to expand...
Click to collapse
Use a download manager like "free download manager" or something. I am on a slow network to re-upload it else where.
kkdevta said:
Use a download manager like "free download manager" or something. I am on a slow network to re-upload it else where.
Click to expand...
Click to collapse
I don't know how to thank You.. But thanks a lot you safe my days..
Can any one plz give me the link of any custom recovery for asus zenfone c.....i badly need it plz help me...thnks in advance.....plz give me..and tell me how to flash it.....
do you know where i can find the correct .raw file for asus zenfone 5 A501CG ? i use lollipop, i dont know if that's matter =s
Anyone help me When I press volume- and power, it can't enter to fastboot. And when I plug the cable, the flash tool can't detect it
Sent from my Mi 4i using XDA Free mobile app
hello brother...can you help me...
my zenfone 5 a500cg has been softrick and bootloop to...
if i'm turn on my phone
logo asus and then usb logo and then dead again...
i can't log into fastboot(power on+vol up)..
but i can log into cwm philz...
i try flash via adb sideload but always error bla bla bla tmp/updated.zip
if i try other ROM always like this ( please upgrade to image 4.3 first)
i try xftsk but always windriver error( i am use notebook win7)
i try asus flashtool with .raw zip rom but my serial number error just 12345678abcdef...
if i click start always device not detect...
help me bro
disappear3896 said:
Anyone help me When I press volume- and power, it can't enter to fastboot. And when I plug the cable, the flash tool can't detect it
Click to expand...
Click to collapse
power and volume up (+)
Spartan Legionnaire said:
IT WORKEEEED!!!! I dont know how to thank you man!. Thank you so much, I was going to give up on this device!. Its working really well.
The only thing I came into trouble, was to install the USB drivers included in the Asus Flash Tool. I did the following (on Windows 8.1 64bits):
I disabled driver signature check first on windows.
I went to the USB drivers folder inside the ASUS Flash tool folder on Program Files.
I went here C:\Program Files (x86)\ASUS\ASUS Flash Tool\Driver\USBDriverInstaller\devcon\x64
On that folder, there is a program called devcon.exe, right click on it, and select properties.
On compatibility tab select Run as Administrator, click ok.
After this, reinstall USB drivers by going to C:\Program Files (x86)\ASUS\ASUS Flash Tool\Driver\USBDriverInstaller and here execute install_drivers.bat
Thats it, the phone now should be recognized by the Asus Flash Tool.
Click to expand...
Click to collapse
First and foremost, follow Spartan about how to deal with the driver install error. Read above. Second, those are the links for the raw images:
ww_A500CG_3.23.40.60_20150630.raw and many other phones. It was posted by thanhthuy. 500CG Lollipop: https://mega.nz/#!jwBDUKzJ!x3VD9VJrMe0CBs353DVnXlHr2dHQXepjcqtrR0gQDdU
500CG kitkat:
https://mega.co.nz/#!H8YkyLba!4Ye52JKAjzogGRVvCx2r9XoJIhou_uY3z6YH1xBges8
400CG 6.6.3 - https://mega.co.nz/#!HoRRnLCL!CV-iCMEUgRd_LwDc4QgNkevxKIGOKtFGDYrytt59EVE
400CG 7.3.3 - https://mega.co.nz/#!G8hRwYqR!Eu_l6r_6QSbhjID-MtYQU3v0q0voQ0GYkFeayy-3MFI
451CG: https://mega.co.nz/#!794U1TpT!rermqclZOpPKcYZY8z2YezUkQE-MWjYJgqyKMUAjYDo
600cg Kitkat: https://mega.co.nz/#!S1wlnYhC!doCPvf7ukeEFStcJPgqaEViE5oiHb_hpGSGnIh3n1IQ
Here for 600cg lollipop: https://mega.co.nz/#!3p4wBQAY!KUx26zaGdCBU6CGa4g68zT_iX9NxmIQCUvHiolfa_Oo
ZE550ML Lollipop 40.23 : https://mega.co.nz/#!HgBSySZA!EOxpsmPvHgCfl-9jUVRAv624Uq9LG4uvxuN83j6-P-k
ZE550ML Lollipop 40.40: https://mega.co.nz/#!P4RmXIwb!-xrDe8AYXdprZgUG4Ehs8fLNHhrdKpXdmaV3FBWPC_0
ZE551ML Lollipop: https://mega.co.nz/#!i4JRAQDR!9DzxtSd1oxDuCV6oc0rEhm-1sF4SA-94YPG9fLVw_lw
Source using Google cache (Vietnamese): http://webcache.googleusercontent.com/search?q=cache:w5AS-N1JrAoJ:zenphoneviet.com/threads/all-zen-stock-rom-firmware-kk-l-update-hang-tuan-chay-bang-asus-flash-tool.7066/+&cd=1
---------- Post added at 07:31 AM ---------- Previous post was at 07:29 AM ----------
Those raw files are extremely difficult to find so if you pretend to have any of those phones i recommend to download. It works easily if you have fastboot. If you only have adb i did not saw working but i am trying.
---------- Post added at 07:38 AM ---------- Previous post was at 07:31 AM ----------
If you try to do that under adb they give a serial number mistake.
4 days trying to solve this bootloop using adb. At least one person here saved his phone with the raw links i found using google webcache in this vietnamese link so it was worth it. Looks like i will need to lose 40 days sending to Asus in Sao Paulo. What a hell folks, those asus firmwares are really crap. Set a great hardware for set poor software.
why my phone does not give any reaction when press power button+vol
I had same problem but different situation....I tried to make an experiment by changing systemui and I had done it with a wrong step .lucky I make a backup and tried to recover it.
But Things get worst when it failed to backupbang now my phone get stuck to Asus logo.I tried to follow the method that your all give in this thread but I can go to fastbootode with it must press power button+col down button.
CAN ANYBODY HELP ME WITH THIS PROBLEM
Sorry for my bad English
And I'm a newbie and try to learn something from pro
Hello to you all. Since I got a new device (LG G3) I thought it will be cool to write an in-depth guide about recovering a hard-bricked L7 II. Our guinea pig will be my P710. All devices have the same internals. I will write up when you need to do something different depending on your model. This will work for the people that flashed a P700 image and lost Emergency Mode. This will probably work in any hard-brick unless your eMMC failed or it is broken (physically).
FOR THE PEOPLE THAT FLASHED L7 FIRMWARE ON L7 II AND HAVE THE ODD EMERGENCY MODE AND CAN STILL SEE ANYTHING ON THE SCREEN INSTEAD OF THE OPENING AND SHORTING PINS GO HERE: http://forum.xda-developers.com/opt...unbrick-lg-l7-ii-flashed-l7-firmware-t3177181. Follow the Steps there and then return to this tutorial to the QDL 9008 part.
The original tutorial for this unbrick was made available on 4pda (Thank you very much guys; Your names will be in the credits area). Also some of the files (most of them) are from 4pda (Thanks again).
This is not exactly the same tutorial. I changed some things and I made some things my own way.
This is not a beginner friendly task but I will write it very in-dept (still not step-by-step). Very low skills are required though: follow exact directions, read carefully and don't do stuff because you think it is good.
I am not responsible for any damage to your phone, if you get fired from your job because your alarm clock failed or you destroyed your device even further. YOU TAKE THIS ACTIONS AND IT IS YOUR OWN RISK. I CANNOT BE HELD RESPONSIBLE FOR ANY OF THIS ACTIONS. This tutorial includes parts that might be illegal in some states (like changing IMEI back to your device one). If you are in one of those states please skip this. IMEI change is illegal (well, I am not a rule breaker but we are just gonna restore our default IMEI).
This Tutorial will be divided in parts:
1. Needed tools/drivers and preparation
2. Opening the phone and exposing the motherboard
3. Getting the device into QDL Mode 9008
4. Flashing the MBR, EBR and the main bootloaders
5. Flashing the phone as a Hard Drive in QDL Mode 9006 (Raw MMC Access)
6.1. Flashing a Pre-Rooted Image
6.2 Restoring the default Emergency Mode
6.3 Restoring original IMEI (if this is legal in your state)
7. Flashing your desired KDZ for your phone model.
1. Needed tools/drivers and preparation
Physical tools:
Frearson (Star) Screwdriver 2.0mm
Plastic Opening Tool
A cooper wire (not very big in diameter that is very sharp at 1 end)
USB Cable
Optional: A Loupe and a Motherboard Holder
Optional: A tool for releasing the plugs on the motherboard
This are my tools and of course the USB Cable.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Software:
LG Drivers
Adb for Windows
KDZ Flasher
QDL Drivers (32 and 64 bit)
QPST Tools (Qualcomm Service Tools)
MBR and BL Repair
EMMC RAW WRITER
HxD Hex Editor for Windows
Root.kdz
Stock_Emergency.rar
IMEI_Single.qcn
IMPORTANT: During all this tutorial RUN ALL PROGRAMS WITH RIGHT CLICK "Run As Administrator"
Download all the software and install Adb for Windows and LG Drivers and restart your computer.
VERY IMPORTANT STEP: When restarting and booting-up keep hitting F8 and get to the Advanced Boot Menu. Go down and hit “Disable Driver Signature Enforcement.” (AFTER THIS STEP DO NOT RESTART COMPUTER; It will temporary disable driver signature since QDL drivers are not digitally signed).
2. Opening the phone and exposing the motherboard
Open the back cover and plug out the battery. Plug out the Sim Card and Sd Card if you have any plugged. Using your screwdriver unscrew this screws.
Insert your opening tool (it must be a plastic tool like in the photo) above the power button and gently move it all across the cover so you unclip it. You can then lift off the cover and you will see the phone motherboard. If you get stuck in the case then lift up and down gently. Remove the 3 buttons and put them safe. (Power, Quick Memo, Volume).
Now remove the 7 connectors like in the image. CAREFUL. IF YOU DAMAGE ANY OF THEM YOU WILL LOSE THEIR FUNCTIONALITY. THERE IS NO WAY TO REPAIR IT. THEY SHOULD COME OFF EASY. Use your tool or your nail but with great care.
After that lift the motherboard (the green one) while you gently pull the connectors out of the way. Turn the motherboard on the other side and you will see something like this.
Hold the board in your hand and you will see the space above the battery connector. Pull gently with your nail until you hear it uncliping .
Turn it on the other side (not on the back, just rotate). You will see another space pull it up like you did it first time and pull the heatskin off. You will see something like this.
After this plug just connector number 1 and turn the motherboard on the other side (motherboard should not stay on connector number 3 you should pull that away when you turn the board.
We are done with this step
3. Getting the device into QDL Mode 9008
Now we need to use our polished cooper wire and ground 1 thin resistor to get to test-point mode. You need to ground this end of the resistor:
Ignore the white stuff (it is flux) on the GND point. Yours will be gold. Just short where the red dots are (the ground and the 6th resistor, the up pin of the resistor). While you keep it shorted plug in USB connected TO BACK PORT OF YOUR PC. BACK HUB NOT FRONT. If you don't get the beep for a new device detected unplug USB, short again and plug USB. After your device gets detected hold the short for 2 more seconds and then remove the cooper wire (or what you used to short).
I did it alone but you can ask 1 people to help. One keeps it shorted and 1 plugs USB. AFTER DEVICE GETS RECOGNIZED AS UNKNOWN DEVICE DO NOT UNPLUG USB OR YOU NEED TO SHORT AGAIN.
Go to Device Manager and select driver for your unknown device. Select the 32 bit or 64 bit driver you just downloaded at step 1 (depends on your OS if it is x86 or x64). Wait and your device will look like this.
Click Have Disk.
I have 64 bit PC.
FINAL RESULT SHOULD BE THIS.
4. Flashing the MBR, EBR and the main bootloaders:
After you got the Final Result install QPST tools and open eMMC Software Download. You will need the QDL_9008_L7II.zip files now. Do like in the image:
At 1 choose your phone.
At 2 Write:
Code:
MPRG8X25.hex
At 3 Write:
Code:
8X25_msimage.mbn
At 4 Press it and select the file rawprogram0 in your QDL_9008_L7II folder.
At 5 Press it and select the file patch0 in your QDL_9008_L7II folder.
At 6 Uncheck Program MMC Device
In the end it should look like this.
Press Download
Wait it to finish. Your device will make recognition sounds and it will say device ready to use. You are now in QDL 9006 (RAW MMC PROGRAMMING). The Final message should be:
You will see some messages like this:
The Letter might be different but ALWAYS DO NOT FORMAT. AGAIN!!! SAY CANCEL!!! ALWAYS
After you say CANCEL close eMMC Software Download.
5. Flashing the phone as a Hard Drive in QDL Mode 9006 (Raw MMC Access)
Open EMMCRAW program with Run As Administrator. You will need the LG_P715_FullFlash.rar. Unrar that and you will get a *.bin file we will need. Do like in the image and select the LG_P715_FullFlash.bin you just extracted. Then Press Write.
You might get a message like this:
If you get this press YES, if not it is just as good. If you will get the message it will stop at 99% flashing and give an error in the bottom left corner IGNORE IT. Wait until it is done and do not unplug the phone or restart the computer.
It will take up to 30 mins. After all buttons but Cancel are not grayed anymore it means it is done. Close the program. Unplug USB, Unplug the connect 1 on the motherboard and assamble the phone back like in step number 2 but in reverse order. DON'T FORGET ABOUT THE HEAT SKIN.
6.1 Flashing a Pre-Rooted Image
After you successfully assembled the phone plug battery. Hold down Volume Down and plug USB Cable. You will hear a beep and see some Strange screen with blue strips if you see this your phone is forever dead. Just kidding this is normal. Your phone is getting detected in this strange Emergency Mode.
If you don't see the blue screen it means you have L7 II Dual Sim (I am not sure since I don't have dual sim; this needs confirmation since I don't know if the OEMSBL is the same for Single and Dual). Do the 6.2 Restoring the default Emergency Mode if you see this blue screen like in the image.
Unrar the Kdz Flasher and from that folder install "msxml.msi". After that run "KDZ_FW_UPD.exe" as administrator. Do like in the picture:
1. Select 3GQCT
2. Select Emergency
3. Browser for the Root.kdz you downloaded at first step
4. Press the button and wait until your phone reboots
When it rebooted, unplug USB Cable, plug out the battery. Put it back. Press Volume Down+Home Button+Power Button. When it powers stop pushing Power. Wait until you see the Android Guy (this will hard reset your device).
When it booted up complete the Startup Wizard randomly to get to system. Go to Settings->Developer options and Enable USB debugging. Wait for drivers to install.
6.2 Restoring the default Emergency Mode
Plug in USB Cable.
Unrar the Stock_Emergency.rar and put the 3 files inside on the root of your SD CARD (you need an SD Card).
From ADB copy this. LINE BY LINE OR YOU CAN HARD BRICK YOUR PHONE AGAIN:
Code:
adb shell
su
Grant Su permission on phone.
Copy the next lines 1 by 1 pressing Enter after each one.
Code:
dd if=/storage/external_SD/cfg.img of=/dev/block/mmcblk0p1
dd if=/storage/external_SD/qcsbl.img of=/dev/block/mmcblk0p2
dd if=/storage/external_SD/oemsbl.img of=/dev/block/mmcblk0p3
Close ADB and reboot device.
6.3 Restoring original IMEI (if this is legal in your state)
This will include a split A (Single Sim) and B (Dual Sim). For Dual Sim restore I don't have a device and I am still experimenting it will be available later.
Be sure to have USB Plugged in and download, depending on your phone IMEI_Single.qcn or IMEI_Dual.qcn (not available yet).
Now we need to convert our IMEI to good form. Look under the battery and note down the IMEI on a paper (I will take as example 123456789123456). Apply this Algorithm:
Split the IMEI in 2 digits groups with the first group being 1 digit:
Code:
1 23 45 67 89 12 34 56
Add A in front of 1:
Code:
A1 23 45 67 89 12 34 56
Reverse order of characters in each group and you will get:
Code:
1A 32 54 76 98 21 43 65
Note this on the paper. Do this for each IMEI if you have a Dual Sim.
Look in device manager for your device under Ports (COM & LPT). See what COM your device it. We will note it COMxx (where xx is your COM number).
Open QPST Configuration and go to Ports window and follow instructions in the pictures:
Close QPST Configuration.
Open the IMEI_Single.qcn with HxD. Press Ctrl+G and write 22A49 and press OK. Write on Keyboard the IMEI after conversion (ex 1A 32 54 76 98 21 43 65) and Save the file.
TO COME FOR IMEI_DUAL.qcn
Open adb and do this:
Code:
adb shell
su
dd if=/dev/zero of=/dev/block/mmcblk0p6
reboot
When phone is fully restarted open Software Download (from QPST).
Do like in image.
Go to Restore at 1.
At 2 select the Port you just added in QPST Configuration.
At 3 select IMEI_Single.qcn.
Check at 4. At 5 Press Start.
Phone will reboot and you have Stock IMEI. Good Job.
7. Flashing your desired KDZ for your phone model
For this step follow 6.1 but instead of Root.kdz use the Firmware for your phone.
GOOD JOB FULLY STOCK. YOUR BRICK IS BACK. BIG THANKS 4 PDA. NOW CREDITS!. Part of tutorial and files are from here: http://4pda.ru/forum/index.php?showtopic=466295&st=3620#entry40156281
From 4pda:
Pixars
VVitaly
ArtemDmuh
From xda:
@maxx_hr
@DS_katauri
Hard bricked lg l7 ii
My phone has the exactly same case with this case..cannot log into emergency nor recovery mode..my friends told me thatnit might be flahe with the wrong firmware..i try to follow your step of recovering the device, but i'm stucked at the point of finding LG_p715_fullflash.rar...i've googling but still cannot find the download link of the file..would you please give me the link of this file...i really need it..please..god bless..
---------- Post added at 11:04 PM ---------- Previous post was at 10:59 PM ----------
Revision
My phone has the exactly same case with this case..cannot log into emergency nor recovery mode..my friends told me that it might be flashed with the wrong firmware, i flashed it because my device was dead when i try to decrypted it..i encripted it because i want to sell my device, but i cancel it..
I try follow your step of recovering the device, but i'm stucked at the point of finding LG_p715_fullflash.rar...i've googling but still cannot find the download link of the file..would you please give me the download link of this file...i really need it..please..god bless..
edikakadul said:
I try follow your step of recovering the device, but i'm stucked at the point of finding LG_p715_fullflash.rar...i've googling but still cannot find the download link of the file..would you please give me the download link of this file...i really need it..please..god bless..
Click to expand...
Click to collapse
Find it there:https://www.boot-loader.com/eng/medusa_free_section
Restoring default emergency mode
6.2 Restoring the default Emergency Mode
Plug in USB Cable.
Unrar the Stock_Emergency.rar and put the 3 files inside on the root of your SD CARD (you need an SD Card).
Which file is stock emrgency.rar??..so sorry..god bless..
Forgot to upload it. I am on vacation now. Will upload in 3 4 days. All the best.
Sent from my LG-D855 using XDA Free mobile app
neutrondev said:
Forgot to upload it. I am on vacation now. Will upload in 3 4 days. All the best.
Sent from my LG-D855 using XDA Free mobile app
Click to expand...
Click to collapse
Great..
I've done the step you instructed..but after flashing the pre rooted image, my device dont want to 'find' the android guy you meant..still in blue striped mode (my device in white stripes mode)..was there something went wrong on my job??
By the way..happy vacation!!! Hope you enjoy it..all the best..
edikakadul said:
Great..
I've done the step you instructed..but after flashing the pre rooted image, my device dont want to 'find' the android guy you meant..still in blue striped mode (my device in white stripes mode)..was there something went wrong on my job??
By the way..happy vacation!!! Hope you enjoy it..all the best..
Click to expand...
Click to collapse
File Uploaded check post number 1. Also the procedure to make the android guy appear is hard reset. What is the combo for P715?
neutrondev said:
File Uploaded check post number 1. Also the procedure to make the android guy appear is hard reset. What is the combo for P715?
Click to expand...
Click to collapse
Dont know the combo..sorry brother..Is it there any way to put back my device into the previous mode??? QDL mode maybe??! I wish I could start it over again..
---------- Post added at 07:21 PM ---------- Previous post was at 07:16 PM ----------
neutrondev said:
File Uploaded check post number 1. Also the procedure to make the android guy appear is hard reset. What is the combo for P715?
Click to expand...
Click to collapse
By the way...my phone was totally dead before..great thanks to you...so happy to have something on my lg p713 screen..thanks again bro..
edikakadul said:
Dont know the combo..sorry brother..Is it there any way to put back my device into the previous mode??? QDL mode maybe??! I wish I could start it over again..
---------- Post added at 07:21 PM ---------- Previous post was at 07:16 PM ----------
By the way...my phone was totally dead before..great thanks to you...so happy to have something on my lg p713 screen..thanks again bro..
Click to expand...
Click to collapse
You could flash the prerooted image and boot it?
neutrondev said:
You could flash the prerooted image and boot it?
Click to expand...
Click to collapse
Flash complete..hard reset..no android guy..still striped screen..
Almost give up brow..
edikakadul said:
Flash complete..hard reset..no android guy..still striped screen..
Almost give up brow..
Click to expand...
Click to collapse
Make me a picture. I don't understand can you boot it? If you could flash the kdz you can hard reset also.
Thank you very much.
With your post and help @maxx_hr I managed to get my cell phone out of the dead . Once again thank you very much ..
Sorry on my bad english.
This project is now discontinued because I am dropping this device.
Sent from my LG-D855 using XDA Free mobile app
Thanks for your help. I followed your tutorial but I can not move in step 4.
When I using eMMC Software Download is done perfectly, makes the sound of the new device, but does not give me the message "DeviceArrival ...", only the result:
"Download completed - no errors detected
Timeouts: 1st dev arrival 60000 ms, 10000 ms linger time "
Any idea that was wrong?
Sorry for my English.
P.D.: My dev: LG L7 II (p710)
Also works on LG L5 II
This also works on LG Optimus L5 II?
Someone could help me with my phone? http://forum.xda-developers.com/opt...question-hard-brick-lg-optimus-l5-ii-t3254224
excellent
I have been very useful this post could solve the problem with 3 cell q were freaking me out here in the workshop
so I have to thank and ask apologies has errors 'm using a translator do not speak English only Portuguese
i take paragraph asking whether there is a process similar to Samsung i9500 s4 q the same in this way does not accept the call recording and goes straight to the download mode