A day or so after upgrading to Jokersax's 0.5.0 build for the Atrix with the Aroma installer, I've discovered that some of the letters on on the keyboard stopped working. Using Touch Test, I've confirmed that there is a roughly 1 inch vertical stripe of my touch pad that just does not register inputs.
Downgrading to previous builds or restoring previous backups of the ROM do not fix the issue.
Is there a chance that the touchpad calibration utility for Aroma caused a miscalibration of the touchpad? Or is this likely physical damage of some sort? I've already tried rerunning through the Aroma installer and recalibrating the touchpad to no good effect.
Any other suggestions from folks?
-----
Update: Solved by replacing the screen/digitizer
mines is doing the same exact thing. from what i have read on there your digitizer is going out. I ordered another one and it should be here today, once I install it, I will let you know if it continues to do this or not.
The digitizer is a common issue with the Atrix. Motorola went cheap on the Atrix.
Funny. I also started experiencing this last week.
How much did your digitizer cost? ( @ Quinto)
Sent from my MB860 using XDA
I just installed JokerSax 0.5.0 2 days ago as well, and today I have noticed a strip up the entire touch screen that is not responding to input. I too used Touch Test to confirm that there is a strip from the back key, all the way up to between 'OROL' in the word Motorola at the top of the phone.
This affects keys B H and Y when in portrait, and the entire qwerty row when in landscape with the usb port to the top.
I dont recall this happening before running Jokersax CM9 but it very well could have been..
shirzadians said:
Funny. I also started experiencing this last week.
How much did your digitizer cost? ( @ Quinto)
Sent from my MB860 using XDA
Click to expand...
Click to collapse
got for $33 off of eBay. Here is the link:
http://www.ebay.com/itm/OEM-Motoroloa-Atrix-4G-MB860-digitzer-frame-/251030640695?pt=LH_DefaultDomain_0&hash=item3a72979837#ht_5015wt_754
It came yesterday and I am going to attempt to put it on tonight.
Thanks, and good luck. Keep us posted.
Sent from my MB860 using XDA
Somebody gave me a stock atrix with a similar condition, it was about 1/2 inch at the top and another 1/2 inch near the bottom (in portrait) mode.....so it's not the rom that you installed.
I too ordered a new digitizer off ebay....except mine cost $43 :-( i should have looked for a little longer...ohh well
I don't think it's necessarily a hardware issue :
The fact that it happened just after installing a new ROM is very disturbing
I have the same problem, and sometimes, with a new ROM, the problem disappears for a couple of hours, then my screen goes totally crazy, then the unresponsive strip reappears
Some people have this problem and a new digitizer didn't solve it
Is there any way that CM9-based ROMs overwrites some touchpad driver ? Does someone else could testify that it could be something else that the digitizer ?
Interesting idea. For the record though, I'm running pure CM7 RC 2. I have heard that the reason one might lose and then regain touch response is due to a hardwear connection/reconnection issue.
When this problem first began to occur, I would briefly retain touch response in the dead strip after rebooting. To test if this was a software or hardwear issue, I physically twisted my phone a few times and regained touch response temporarily, suggesting a hardwear response.
Just my two cents.
Sent from my MB860 using XDA
Anyone have luck with the replaced digitizer yet? I'm hoping to avoid ordering if that doesn't resolve the issue.
Ok, I broke down and bought the digitizer from ebay via the link that quinto0827 provided. I just installed it, and things are working great.
shirzadians said:
Interesting idea. For the record though, I'm running pure CM7 RC 2.
Click to expand...
Click to collapse
Off topic, where did you find cm7 rc2? All I'm finding is rc1 which is what I'm running.
David Guillot said:
I don't think it's necessarily a hardware issue :
The fact that it happened just after installing a new ROM is very disturbing
I have the same problem, and sometimes, with a new ROM, the problem disappears for a couple of hours, then my screen goes totally crazy, then the unresponsive strip reappears
Some people have this problem and a new digitizer didn't solve it
Is there any way that CM9-based ROMs overwrites some touchpad driver ? Does someone else could testify that it could be something else that the digitizer ?
Click to expand...
Click to collapse
I think the same thing.
I had the same problem with my Huawei Ideos U8150 after flashing Dronix 0.5 Rom.
In CWM I can see that the digitizer every 2 seconds it loose my fingers.
same has happened to me on my atrix. one perfectly straight line down the screen which doesnt react to touch. This line is moveable within the aroma installer calibration tool, which btw is what created the problem for me in the first place, after i decided to try the alternate touch option.. So yup, i agree too. I KNOW it was aroma installer that messed my atrix up.. SIGH...And i had just gotten it running top notch too..grrr .. btw that new touch file manager installed through cwm will also move this ghost line around, which could perhaps help some users navigate a little better on their touchscreen.. This is another point that suggests its not a hardware issue. Only other, worse thing i can think of is that the aroma touch installer played with the voltages feeding the screen, and did maybe blow something physically.....
Hey look at this... Just happened today and im so sad... Sometimes this solution in the link seems to work so it should be a hardware issue... http://forum.xda-developers.com/showpost.php?p=27595402&postcount=1
Related
Hi guys, my Hero encounter the touch screen doesn't work periodically, sometimes it became no response totally, after a few days ,it works well, I think this may be caused by the static electricity, Is there anyone have the same problem? do you guys have some methods to solve it ? Do I need to change a new touch screen?
well i droped mine today and now i have the same issue but the strange part is that i just had a replacement screen and there are no cracks or anything else, so you can't see that it felt out of my pocket.
Hello I had the same problem.
I installed several versions of Android and nbh files.
The problem occurred with versions nbh for Froy version of Android.
As I had saved the versions that were tested. I tried to install previous versions where I knew the touchscreen worked correctly. In my tests with this file to the touch screen work again: kaisimg-panel2-320-24-05-10.nbh
I hope that helped
when you say not working properly, what do you mean? the a and l letters on the keyboard dont register unless I press the screen really HARD. so that aria of the screen is unresponsive
what does one do with kaisimg-panel2-320-24-05-10.nbh?
angelodt said:
Hello I had the same problem.
I installed several versions of Android and nbh files.
The problem occurred with versions nbh for Froy version of Android.
As I had saved the versions that were tested. I tried to install previous versions where I knew the touchscreen worked correctly. In my tests with this file to the touch screen work again: kaisimg-panel2-320-24-05-10.nbh
I hope that helped
Click to expand...
Click to collapse
Hmm please can you explain what this means ? and where we can find that file because I have the same problem... And now your screen is ok ?
Man one thing I hate about this site is that people do good write ups and it never gets solved!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I got the same problem!! whats the fix? screen replacement? cord lose? what what ?!?!?!!?
This has been discussed a milion times in the General forum.
Screen problems happen to a lot of Hero owners. Just send it to HTC fir a new screen. Don't forget to install an original ruu-rom on it.
Sent from my HTC Hero using XDA App
mach2005 said:
This has been discussed a milion times in the General forum.
Screen problems happen to a lot of Hero owners. Just send it to HTC fir a new screen. Don't forget to install an original ruu-rom on it.
Sent from my HTC Hero using XDA App
Click to expand...
Click to collapse
I'm over the warranty. How can I fix it? does the screen need replacing? is the cord detached? whats the common issue of this happening? Whenever I touch my screen the notification bar drops down all the time.
i just purchased a old htc hero selling my spice mi300 i usualy get thr same problem in the lower part of thr screen may be i have to.just live with it as there is no warranty or insurance
I have had the same problem.
Mine is fixed within the warranty period.
But i have read something about failing Digitizers.
Maybe that's the problem?
See this topic:
http://forum.xda-developers.com/archive/index.php/t-595485.html
You can buy them at Ebay just look for HTC Hero digitizer.
Below you find a link to the service manual:
http://www.gizmostruction.se/wp-content/uploads/2010/04/Hero_Service_Manual.pdf
If your phone is out of warranty
Maybe you can fix it by yourself
Anyone have an issue with their touchscreen where there is a "dead spot"? I don't know how to describe it other than that. There is a spot if I touch it, nothing happens. It is right where the Accept and Download button is on the market in portrait orientation. It seems to be all the way across the screen in a horizontal line. Pixels and color are not affected just the touch effect. If i reboot, it goes away for a while. Switching ROMs makes no difference, happens on every one I have tried though, so it seems to be a hardware issue. Any help would be great.
nicktheqwik82 said:
Anyone have an issue with their touchscreen where there is a "dead spot"? I don't know how to describe it other than that. There is a spot if I touch it, nothing happens. It is right where the Accept and Download button is on the market in portrait orientation. It seems to be all the way across the screen in a horizontal line. Pixels and color are not affected just the touch effect. If i reboot, it goes away for a while. Switching ROMs makes no difference, happens on every one I have tried though, so it seems to be a hardware issue. Any help would be great.
Click to expand...
Click to collapse
If you had searched the forums, you would have come across this, which will solve your problem.
Also, it's not flashable so unzip it and put the apk on your phone, install it, then run.
nicktheqwik82 said:
Anyone have an issue with their touchscreen where there is a "dead spot"? I don't know how to describe it other than that. There is a spot if I touch it, nothing happens. It is right where the Accept and Download button is on the market in portrait orientation. It seems to be all the way across the screen in a horizontal line. Pixels and color are not affected just the touch effect. If i reboot, it goes away for a while. Switching ROMs makes no difference, happens on every one I have tried though, so it seems to be a hardware issue. Any help would be great.
Click to expand...
Click to collapse
Try to find the HTC Calibrate.apk and push it to System/Apps... It'll Definitely Help!
Twolazyg said:
If you had searched the forums, you would have come across this, which will solve your problem.
Also, it's not flashable so unzip it and put the apk on your phone, install it, then run.
Click to expand...
Click to collapse
I ran the advanced search and couldn't find anything for the E3D. But thanks for the help and for the hand-slap dude.
nicktheqwik82 said:
I ran the advanced search and couldn't find anything for the E3D. But thanks for the help and for the hand-slap dude.
Click to expand...
Click to collapse
Really? After about 1.4 seconds I had 4 touchscreen issue threads (including this one.) pop up after searching "touchscreen issue" in the "search this forum" bar. Did you fix your problem?
No go.
Well the HTC Calibrate app did not work. I must say that it did help for sure, but the same dead spot issue keeps happening. OK, so now I have begun to look at replacement parts on Ebay. So just to get this straight, it is the digitizer/front glass assembly that registers touch, correct? As I said, there are no missing pixels or colors, so does that rule out the LCD? Or should I but both to be on the safe side? I really want this issue done and over with, so help me get this thing taken care of guys. Thanks to all you guys for the help. Also, if anyone has a digitizer and LCD assembly for a good price, let me know.
I had the same issue where the bottom quarter of my e3d hboot 1.5 didn't work I didn't have insurance so I took it in and the sprint manager said I wasnt the only one with the issue it's a htc issue I tried the calibration on different roms bit it would only give you calibration on the top half of the screen, spent swapped it out and I got a new e3d with hboot 1.5 of course but at least the touch screen is working.....hoped that helped you out cuz I searched everywhere and couldn't find a solution.
I was toying with that idea. Will the "watermark" from unlocking a 1.50 hboot version be a problem? Obviously I need to unroot. And also, I bought this phone from an individual just a few weeks ago after I got my first one stolen, will this be a problem? Any other thoughts on taking it back to sprint?
Yeah, it is really weird, it is exactly where the "Accept & Download" button is when making a market purchase. So, yeah it sucks, I have to rotate it horizontal every time I want to buy something
I have been having lots of touchscreen issues as well. Tried lots of different roms and kernels but no luck. Someone suggested formatting the SD card. I haven't had access to a computer so i just removed the card about an hour ago to test and so far i haven't had any issues.
Sent from my PG86100 using xda premium
I got my Titan today and the first thing I noticed was that the touch was a bit slow, nothing to really care about but coming from the iPhone I expected the same "tracking" but it ain't there. Anyone else feeling this?
ArtieQ said:
I got my Titan today and the first thing I noticed was that the touch was a bit slow, nothing to really care about but coming from the iPhone I expected the same "tracking" but it ain't there. Anyone else feeling this?
Click to expand...
Click to collapse
You on 8107? Did you start out with a Fresh Install? Any apps that might cause this?
Probably Digitizer issue... If you got warranty with AT&T/UK/whoever replace it
Tachi91 said:
You on 8107? Did you start out with a Fresh Install? Any apps that might cause this?
Probably Digitizer issue... If you got warranty with AT&T/UK/whoever replace it
Click to expand...
Click to collapse
Yes 8107, I booted the phone and I had a few updates available so I updated it completely (I don't know what firmware it was from beginning, but definitely Mango at least). I'm not sure what you mean with Fresh install, please elaborate.
ArtieQ said:
Yes 8107, I booted the phone and I had a few updates available so I updated it completely (I don't know what firmware it was from beginning, but definitely Mango at least). I'm not sure what you mean with Fresh install, please elaborate.
Click to expand...
Click to collapse
Fresh Install as In... A Factory Reset.... Like its better to start out with a clean slate then to start using a phone that was already being used and had some caches/apps loaded onto it...
Its best to ruled out any software issues before blaming Hardware (replacement)
And the digitizer is definitely not faulty.
ArtieQ said:
And the digitizer is definitely not faulty.
Click to expand...
Click to collapse
Basically if its lagging it would be software related... There's a delay from when you do something to when WP7 responses to it... I would suggest backing Up and doing a Factory Reset and see if it makes a difference.
Did you load up the phone with stuff? Supposedly there's an issue with AT&T models that lag when low in memory even if you don't have that model it could be related
Tachi91 said:
Fresh Install as In... A Factory Reset.... Like its better to start out with a clean slate then to start using a phone that was already being used and had some caches/apps loaded onto it...
Its best to ruled out any software issues before blaming Hardware (replacement)
Click to expand...
Click to collapse
It was brand new, never used before so it should have been from scratch already (I had to go through the setup thing and so on)
Tachi91 said:
Basically if its lagging it would be software related... There's a delay from when you do something to when WP7 responses to it... I would suggest backing Up and doing a Factory Reset and see if it makes a difference.
Did you load up the phone with stuff? Supposedly there's an issue with AT&T models that lag when low in memory even if you don't have that model it could be related
Click to expand...
Click to collapse
I got like 15 apps installed but I really don't feel like resetting the phone, I can live with this.
ArtieQ said:
It was brand new, never used before so it should have been from scratch already (I had to go through the setup thing and so on)
I got like 15 apps installed but I really don't feel like resetting the phone, I can live with this.
Click to expand...
Click to collapse
if it's an ATT model, I won't be surprised. Plenty of issues heard in the past with earlier batches too.
Make sure your thumb is not touching the sides as the screen comes so close to the sides that i was touching it and not knowing it, which made it appear to lag or not press numbers to unlock and such. The easy fix for it was to get a hard rubber case which raised my thumbs up so they wouldn't brush the screen edges when typing.
drupad2drupad said:
if it's an ATT model, I won't be surprised. Plenty of issues heard in the past with earlier batches too.
Click to expand...
Click to collapse
It's not an AT&T model, it's totally unbranded.
ROCOAFZ said:
Make sure your thumb is not touching the sides as the screen comes so close to the sides that i was touching it and not knowing it, which made it appear to lag or not press numbers to unlock and such. The easy fix for it was to get a hard rubber case which raised my thumbs up so they wouldn't brush the screen edges when typing.
Click to expand...
Click to collapse
I press the screen straight on with my fingers. Anyway, I might just be overreacting here but it definately feels like the touch is a liiiiiittle after, delayed or whatever you wanna call it.
Uploaded a video: http://www.youtube.com/watch?v=rFO45-u07AU
Looking at your video it seems perfectly normal to me, None of my WP7 devices have ever been any better than your Titan, (2xHD7 and a Titan) Maybe it's just a case of getting over your last phone and adapting to the way Windows Phone works, Took me ages after win Mo 6.5
Hi ArtieQ,
I have the same feeling as you : the scroll doesn't follow immediatly the finger, compared to my Omnia 7 or my iPhone. I hope HTC will fix this with an update, but I'm dreaming...
clemsouille said:
Hi ArtieQ,
I have the same feeling as you : the scroll doesn't follow immediatly the finger, compared to my Omnia 7 or my iPhone. I hope HTC will fix this with an update, but I'm dreaming...
Click to expand...
Click to collapse
I'm glad I wasn't the only one, because yesterday I was about to send in my Titan for warranty repair but later changed my mind. I really hope this is software related, but I think not.
I was also glad when I saw your post because nobody except you has noticed it. But if you look at any video of the titan, you'll see the problem is always here...
Sent from my TITAN X310e using Board Express
clemsouille said:
I was also glas when I saw your post because nobody except you has noticed it. But if you look at any video of the titan, you'll see the problem is always here...
Sent from my TITAN X310e using Board Express
Click to expand...
Click to collapse
I found this thread as well: http://forums.wpcentral.com/phone-wars/184480.htm
I have both an Omnia 7 and a Titan and one thing i noticed on the Titan is that if I don't hold the phone with one hand and use the other for touch the screen lags and failes to register the finger at times. On the Omnia 7 I don't have this problem. The Titan might be worse either way but it's a huge difference when not holding the phone on my Titan atleast
It's easy to reproduce in some games... I get missed swipes (fruit ninja) or birds that fly when I am still trying to get the perfect angle (angry birds).
I was hoping for a firmware to fix this but didn't know if anyone else have a problem so havent bothered reporting it to HTC. I guess if we don't the wont know it's a problem?
//Mikael P
Its got nothing to do with the OS if someone is wondering that! this is an HTC thing, evry phone from HTC have this, its just thay are not as responsiv as a Samsung phone or an IPhone, just look at HTC phone with Android its the same slow respons. if im not worng, this is an Screen issue, i mean an HTC issue HTC use on there phones.
My nook's touch screen is unresponsive at the left corner bottom (area near the n-hole)
Does anybody have the same one?
I attached the image below
All of the comment are welcome.
Sent from my Nexus 7 using Tapatalk 2
I too have a similar problem except my dead zone is in the upper left.
I wonder if we have a way to recover it to normal?
Sent from my Nexus 7 using Tapatalk 2
Same problem here, I've got it just after flashing to the SGT7 version 12/9, Tried to flash back others version like SGT7 24/11 or event CM7 beta, but the problem still remains.
Have you guys found out the way to solve this? Any help will be greatly appreciated
Edit: I think we got the problem after using the 10 mutil-touched flash app. But I have flashed back to stock 2 touch driver but nothing changed.I think I shoud try again.
http://forum.xda-developers.com/showthread.php?t=2030322
I've flashed pretty much every ROM that has been released, and I really don't believe it is caused from a certain ROM. I have found in messing with several NTs and NCs that the screen will randomly have dead areas. A few times I have seen it get worse over time. It seems to happen more on NCs and is a known problem with them. Maybe revert to stock ROM and see if it still happens. If so, try to get B&N to replace it.
Sent from my NT running Kuzma's CM10.1
hado0601 said:
Same problem here, I've got it just after flashing to the SGT7 version 12/9, Tried to flash back others version like SGT7 24/11 or event CM7 beta, but the problem still remains.
Have you guys found out the way to solve this? Any help will be greatly appreciated
Edit: I think we got the problem after using the 10 mutil-touched flash app. But I have flashed back to stock 2 touch driver but nothing changed.I think I shoud try again.
http://forum.xda-developers.com/showthread.php?t=2030322
Click to expand...
Click to collapse
What is the version of your nook? 8 or 16GB. Mine is 8GB and I knew another one have the same version with the same problem like me
Sad the I am outside the US and no way to send nook back to B&N...
Sent from my Nexus 7 using Tapatalk 2
Isn't there someway to recalibrate the touch screen? One would think this would be a must have developer app or for peeps who are switching back and forth between 2,5,10, point touch and touch area resolution?
Onageric said:
Isn't there someway to recalibrate the touch screen? One would think this would be a must have developer app or for peeps who are switching back and forth between 2,5,10, point touch and touch area resolution?
Click to expand...
Click to collapse
There is a nook recalibration app in the play store. Don't know if it actually does anything, but it is there.
goldwoods said:
My nook's touch screen is unresponsive at the left corner bottom (area near the n-hole)
Does anybody have the same one?
I attached the image below
All of the comment are welcome.
Sent from my Nexus 7 using Tapatalk 2
Click to expand...
Click to collapse
My Nook Tablet got the same problem like yours but the dead zone at top left corner.
Same issue here
Anyone... please help us.. I'm also having same problem.. except for the dead zone on my screen is at both places(top and bottom when held veritcally)
hi guys,
im having a problem with my evo 3d. it seems the lower part of the screen is not working. so i cannot unlock my phone now.
< 0 OK buttons are not working anymore but when i go to camera(no password required for some reason,) that part of the screen is working fine.
wanted to know how can i disable the password at least so i can use it and wanted to know if its a software or hardware problem
thanks
_Intel_ said:
hi guys,
im having a problem with my evo 3d. it seems the lower part of the screen is not working. so i cannot unlock my phone now.
< 0 OK buttons are not working anymore but when i go to camera(no password required for some reason,) that part of the screen is working fine.
wanted to know how can i disable the password at least so i can use it and wanted to know if its a software or hardware problem
thanks
Click to expand...
Click to collapse
is the phone rooted and if so, is it a custom rom?
How much of it isn't working? And is it just unresponsive or is the display out as well?
I have a strip of my screen the doesn't work that's righty over where the top row of keys is.
hi guys,
yes rooted,
virtuous rom dont know what version..
my phone has a passkey lock and the part where the "ok" button row is not working.
please let me know that i can at least disable the password lock..
_Intel_ said:
hi guys,
yes rooted,
virtuous rom dont know what version..
my phone has a passkey lock and the part where the "ok" button row is not working.
please let me know that i can at least disable the password lock..
Click to expand...
Click to collapse
So is it just a strip of the screen?
If you really really wanna be able to get it unlocked, Download the correct version of clockwork mod for our phone one that's not touch, has to use the volume rockers and fresh install the rom, Or as a matter of fact, Just boot into whatever recovery you have and clear data/factoryreset, that'll get rid of your lock pin
Hello from me too!
I have a strip on my touch screen that doesn't work. It's right where the Search button and Install on Play Store is and Clear on the Phone notifications, too.
It had the stock rom, I have replaced the screen with the digitizer when it fell down. It worked after that. I had to unscrew the phone one more time because my LCD was touching the screen and the phone had gone mad. After that, and a couple of days later, I noticed that the strip didn't work anymore. Today I finally flashed a new rom (King Cobra 3d) and nothing's changed so I figured it might be a hardware problem...
What's your opinion?
Thank you!
Common Hardware Problems on evo3D
Its the hardware. and your carrier should change it at no cost. (Sprint)
fatisis said:
Hello from me too!
I have a strip on my touch screen that doesn't work. It's right where the Search button and Install on Play Store is and Clear on the Phone notifications, too.
It had the stock rom, I have replaced the screen with the digitizer when it fell down. It worked after that. I had to unscrew the phone one more time because my LCD was touching the screen and the phone had gone mad. After that, and a couple of days later, I noticed that the strip didn't work anymore. Today I finally flashed a new rom (King Cobra 3d) and nothing's changed so I figured it might be a hardware problem...
What's your opinion?
Thank you!
Click to expand...
Click to collapse
ive had the top bar just under my notification bar non working for a few months now, and its starting to pi$$ me off
I've replaced my digitizer twice myself. I got a cheaper one the first time, and figure that's what I get for trying to go on the cheap. (I was out of warranty). Sorry to say it but it could be that again.
Sent from my shooter using xda app-developers app
I think I don't have a warranty because I've changed it myself. It's my fault...
I think I'll buy a new one... I unscrewed it a while ago so I could see if sth had been misplaced or if the digitizer had scratches or sth like that.
I saw that the ribbon's top had been ripped off right where it bends on top of the LCD... Don't know if that's the problem...
p.s. I live in Greece. My carrier is Cosmote. We don't have Sprint here...
Yep, if the ribbon cable is ripped, that would be your problem. Don't go too cheap on your replacement. Good luck!
Sent from my PG86100 using xda app-developers app
toad6386 said:
Yep, if the ribbon cable is ripped, that would be your problem. Don't go too cheap on your replacement. Good luck!
Sent from my PG86100 using xda app-developers app
Click to expand...
Click to collapse
I wonder why is there only one part of the touch that doesn't work if the ribbon is like that, in the bending spot...
thank you! i'll try it as soon as i can and i'll get back!
If i buy a new one from Amazon will it be allright? It costs around 10 pounds... The other one that i've changed and now it has a problem i've bought it for 60 euros from a local store here in Greece...
fatisis said:
If i buy a new one from Amazon will it be allright? It costs around 10 pounds... The other one that i've changed and now it has a problem i've bought it for 60 euros from a local store here in Greece...
Click to expand...
Click to collapse
The last one I got from Amazon is the one I'm using now (about a month old), and spent $20 US on it, which was NOT the cheapest of them. Not knowing the exchange rate right off hand, would venture to say the one you're speaking of is not a "cheap" one. So go for it. Just take your time replacing it and be careful with ALL the ribbon cables. Good luck!