Serious wifi issues - Motorola Droid RAZR

i know this have been discussed before but there is still no solution.
here s my problem: wifi signal drops suddenly when i hold my phone. ive done sevral speed tests. These tests confirm that holding the phone results in a really bad wifi quality. I ve tried eveything.
does anyone have any ideas? even if its hardware moding
thx

+1
Sad to say, in my tests, by tightly holding the phone, especially at the bottom right, the signal strength reduced by about 20dBm.
Sent from my XT910 using XDA

this really sucks since this phone is pretty good and so far its the only BIG problem i found. and no solutions....

Must be a random problem. I have the RAZR and RAZR Maxx and neither has this problem.

For me, on 2.3.6 wifi signal was low, especially taking phone by bottom, but on ICS, both t-mobile ics and latest eu ics, wifi signal is very improved. Hand issue remains, but signal is for me stronger.

well i guess im just going to wait for stock ics update and hope it improves but im guessing the problem wont disappear since this is clearly a hardware issue. and if this is random then im very unlucky

When software fixes a radio that software usually just makes the signal-strength meter show signal that's not really there.
There are apps on Play that "fix" all kinds of radio problems by installing signal-strength icons with the low-strength indications set inaccurately. It *looks* like more signal, but it's the same low signal you had before.
Signal strength has almost nothing to do with reception anyway. Signal/Noise ratio is what's important, and there's no meter for that. One bar of signal in a very RF-quiet area, is much better than five bars in a computer data center.
"Caveet emter, I reckon!"
- Mark Twain
I have no wifi issues with this phone. The GNex however was unusable at 30 feet from a high-powered Hawking WAP, or an Apple Airport Extreme WAP.
If you have a plastic case, try removing it. Some cases are made with recycled plastic and are infused with conductive material that can act as a Faraday Shield, blocking part of the signal. Easy test, costs nothing but a few seconds...

yea i already knew about the plastic thats why i bought a rubber case. I have to say it helped a little but didnt fix it. the problem is still there.
thx

Haven't seen any problems with my wifi, although I mainly use the 3G simply because I have 4 GB of data a month and I will never use that much when I'm out around town.
If the problem occurs when holding it a certain way wouldn't the simplest solution be to not hold it that way, also be very aware of any metals between you and the router as metals block radio signals, how old is your house, if old enough maybe lead paint, unlikely but just throwing all possibilities out there.

thx for your help. i didnt only test this at home and as for holding the phone im used to hold it like i hold all phones and its pretty annoying if i always have to hold it differently if i want to use the internet

Have you tried the free Play Store app, WiFi Analyzer?
This will help you find out what works/doesn't as it provides more sensitive strength measurements from the chip. It's handy anyway, since it shows WAPs that you aren't connected to. yet.
It's quite possible that your antenna wire bounced off the connector. An insignificant drop of an inch could do that if it was never seated correctly. It would likely operate in a degraded capacity as a result. If you're OK with cracking the case open, that's something quick to check.
How long have you had this phone?
I have never heard anyone complain about the Razr's WiFi reception, so I suspect this is something unique to that phone right there. What is your idea of poor reception? 100 feet, inside, is the practical limit. 300 feet in an open field. Metal wall studs, sheet metal siding, all of these will stop radio waves dead.

marawan31 said:
thx for your help. i didnt only test this at home and as for holding the phone im used to hold it like i hold all phones and its pretty annoying if i always have to hold it differently if i want to use the internet
Click to expand...
Click to collapse
I get that, just trying to "cover all the bases" as they say.

Giblet535 said:
I have never heard anyone complain about the Razr's WiFi reception,
Click to expand...
Click to collapse
Then you haven't been listening. The RAZR is universally acclaimed to have the worst WiFi reception of ANY device since 1999.

im ok with opening it... i actually opened it a couple of times and removed the battery but idk what to look for since nothing is labeled i dont even know where exactly is the wifi ship and antenna. i tested this as close as 6 feet from my router when i leave it on the table i get full wifi signal and speed test at max then i hold it and try... wifi signal goes down and speed test at 3/4 max speed...
thx

It's possible that I have an extraordinary phone then. I decided to compare.
My phone is seeing -60dbm from the Hawking extender that I'm closest to, which is about 20 meters away, behind three stick-frame (pine 2x4 studs, sheetrock) walls. The reading varies dramatically, depending on where I put it on my desk. So let's see what some other WiFi devices do...
My MacBook reads -58dbm. My iPad2 reads -59dbm. An HP Envy 15 reads -65dbm. And a Moto Atrix2 WCS (With Cracked Screen) reads -61dbm.
A transfer of 200MB ("random" data created via linux: 'dd if=/dev/random of=200mb.dat bs=1048576 count=200' so that compression algorithms don't skew the results):
Razr (6.12.79 ICS Black Widow): 9s
MacBook (Lion): 6.5s
iPad2: 10s
HP Envy 15 (Ubuntu 11.10): 7.5s
Moto Atrix2 WCS: 10s
I didn't repeat the test, and that is a busy WAP, but the results are what I expect for battery-operated devices. I also expected the ipad, atrix and razr to lose the race, since they have relatively slow storage systems, which have inherently poor write performance on files of this size (200MB won't buffer at all).
The WiFi cable will look like a white or black wire with a gold junction on the end where it meets the motherboard. I would expect that if you've had the phone open, you would definitely notice a wire hanging loose! I doubt that's the problem, but that wire is a coaxial shielded cable - like on cable TV only really tiny - and you can do all kinds of DIY replacement antenna stuff eg, adding an external jack so you can "beam" WiFi a mile away using a hacked Pringles potato chip can.
I actually think the problem might be RF noise in your environment. Florescent lights (CFLs), computing equipment, HVAC compressors, and motors can effectively "jam" WiFi signals, causing packet transmission failures to increase rapidly as the distance from the WAP increases.
We have a Fluke RF analyzer here, and our WiFi setup is quite good as a result.
Does anyone know if the Razr is unusually susceptible to RF noise? Maybe noise that the Razr generates from the motherboard/CPU/radios/BT? I'm not equipped to test that.
---------- Post added at 09:15 AM ---------- Previous post was at 08:29 AM ----------
Do you have other devices to compare the Razr to?
Did you try pointing all the rubber duck antennas on the WAP straight up?
I just checked an iphone, another ipad, another Razr, and a Dell laptop, and my boss's Razr was technically the winner on signal strength and transfer speed, but let's call it even. There are too many variables, and statistically significant benchmarking is beyond the scope of a forum comment.
The Razr has typical WiFi performance in this environment.

Thank you very much for your post. I did try with the desire z and the evo 3d which are doing jist fine wheather i hold them or leave them on the table: both signal and speed test are amazing compared to the razr (if i hold it). If you could tell me where the wifi ship and antenna are located (a pic maybe) it would be great because when i open the razr all i can see are metal plates everywhere probably for cooling. I dont understand what you mean by pointing all the rubber duck antennas on the WAP...
Thx again

I haven't had a Razr open yet. Even after dropping mine from a motorcycle and watching it slide into a ditch with an inch of water in it. Tough li'l bastards...
The WiFi antenna cable and connector are probably under one of the metal shields.
Most WAPs have 1, 2, or 3 "rubber duck" antennas that you can move to maximize the signal lobe pattern. You can use the WiFi Analyzer app to adjust them, but be prepared to walk a lot...
Others are just a box. The only one of those that *I* know of that works well is the Apple Airport Extreme. The Netgear Wireless-N HD, which is very highly rated, is a P.O.S.: it has a narrow, elongated lobe pattern, and if you're in that narrow lobe, it works REALLY well. If not, you'll be lucky to connect to it. Two people standing 10 feet apart, and one can have great service while the other can't even get an IP address.
The fact that you have other devices working well, and you sound like you've done this quite a bit, I'm guessing you have a problem inside the phone itself.
I manage about 200 phones here, and I haven't heard one word of complaint about WiFi. 3G/4G service? Yeah, lots of complaints about 3G/4G from people out in the woods or working in a valley.
These also work well as a WAP (tethering). We have a few of the Personal WiFi devices - a handheld that converts 3G/4G to WiFi for up to five users - but most people prefer this phone for that.
My old DroidX has a better WiFi antenna, but that's an exceptional phone with only one core: I spit on it. Ptui.

Related

signal issues/death grip???

no I love my sgs2 and so does every that holds it, ive a major issue that i thought was caused by switching from orange uk to o2 uk, but as it happens i have full signal when the phone is rested down... however when i pick it up it drops signal... more often than not the signal completely drops out as does the call and sometimes it just goes down to 1 bar... does anyone else have this problem? ive tried my o2 sim and my orange sim its the same for both... is it possible i have a defective handset ? weak radio ???
heres my quick vid to show you what i mean, apologies for the video quality... filmed on my bb9700
http://www.youtube.com/watch?v=9VthdB4V3D8&feature=channel_video_title
well the GSM and 3G antenna looks to be located in the bottom, back part of the device. so this seems like the exact place your hand would be covering when holding the phone, so i can easily see some significant signal attentuation happening with this phone.
i dont know where the antenna was located on the original galaxy s. but all phones i own always have attentuation. not much you can do about it i'd guess.
Applies to all wireless devices - signal transmits worse through your hand than through empty air. Rules of the universe.
However, I can't seem to replicate what you're seeing. In order for bars to drop, I have to block the entire bottom of my device using both hands. Holding it in one hand doesn't seem to be causing a drop for me.
But again : air > hand for signal transmission.
RogerPodacter said:
well the GSM and 3G antenna looks to be located in the bottom, back part of the device. so this seems like the exact place your hand would be covering when holding the phone, so i can easily see some significant signal attentuation happening with this phone.
i dont know where the antenna was located on the original galaxy s. but all phones i own always have attentuation. not much you can do about it i'd guess.
Click to expand...
Click to collapse
That's right, quick start guide shows the location of the antenna. If you look at the back of the device, the antenna is in the lower left hand corner, opposite the speaker.
When holding the device in your right hand, it should rest in your palm.
Actually holding the device in my right hand doesn't seem to be affecting my signal though, for some reason. I might just be in an area with good signal though (3 bars of h+, stays at 3 bars when holding it in 1 hand, drops to 1 bar when covering the device completely with 2 hands, and then changes to edge with full bars).
I just tested with my S2 and I had no problems whatsoever.
See my youtube channel (../user/Poppefieke) Can't post links yet.
I have some other S2 video's there too
i think sampullen who has been posting quite a few vids on youtube is going to cover this now too, see i hold my sgs2 in my left had for holding when im surfing etc but also when im on calls...
its good to hear some of you cannot replicate this, maybe mines faulty might try to exchange for a new 1 just to be on the safe side
OMG!
can more people confirm if this is real?
is it as bad as the antenna-gate issue from apple or no where as bad
Hey (samjpullen) here
I have been doing the tests like Sticky and have been getting some rather conflicting results to say the least.
I am not in the best area for Orange so i get a weak signal most of the time, when i do the test infront of my iMac and extra screen with the TV, Sky (you know the drill) on it seems to drop down from H with 1 bar, then down to 3G then down to G and then it can jump onto the Edge network (rathe strange)
But when i do this same test in other rooms e.g bathroom, other bedroom, even downstairs with the tv etc on it is fine!
So my guess is that it might be my rooms location and maybe all the electrical equipment within a small space.
AllGamer said:
can more people confirm if this is real?
is it as bad as the antenna-gate issue from apple or no where as bad
Click to expand...
Click to collapse
im hoping no where near as bad and im hoping that i was the only affected, one chap has placed a video reply to mine showing he doesnt have the issue which is good news, lets hope more can confirm im rather a 1 off and that if i replace this unit all will be well...... fingers crossed
cheers sam,
btw ppl follow sam on twitter, guys good!!!

[Q] Prime Evaluation

I've been reading for a while trying to evaluate the different level of Prime problems. My return window for the prime closes tomorrow. I'm an android kind of guy and I also own a Samsung Galaxy S.
I'm trying to evaluate the degree of problem with my GPS, WiFi and Bluetooth.
WiFi
===
Running wifi analyzer on both the prime and the sgs the signal readings are almost similar the connection speeds vary greatly with the prime often connecting at faster speeds. I have several wifi routers in my house for coverage with the same ssid. The prime seems to have a little more problems switching from one to the other but not that much.
GPS
===
My prime gps does work but the reception is much weaker than my sgs. This is especially true from inside my house. My sgs is easily able to see and fix 5-8 sats while the prime is completely blind. Outside the house but not in the city, the results are more encouraging with the prime being able to fix almost the same number of sats than the sgs but I cannot see the exact signal strength. I haven't tested in a city with tall buildings all around.
Bluetooth
=======
I haven't found any tools to evaluate the BT signal strength. I'm able to pair a headset and it appears to work properly but no other tests were made.
Soooo, my questions are: Was there batches of primes that were more problematic than others? Is the unconnected antennas problems random or related to the first batches? Compared to other working prime; is mine as good as it gets or I should roll the dices and try to find a better prime?
My serial number begins with: C1OKAS0xxxxx
Thanks in advance for any replies.
JF.
Sounds to me like you have a good one. Your wifi works well compared to your other devices LR even better. You have a working GPS. despite being weaker then your other device it works. Asus removed GPS spec so consider yourself lucky on GPS side. Then for BT seems like you have no issues. I'd think your device was a keeper. As far as wifi antennae issues, that's very random and very small in numbers compared to overall prime users here in xda. The biggest complaint is GPS, not wifi. The other gripe is some experience slowdown of speeds when BT and wifi are both streaming data. But you have alot also that don't experience that. So I wouldn't be too pressed about it. If your device works well, keep it. Or you could gamble on a new device. It could be better. But it could also not be. All primes no matter the batch has the identical same hardware. I have an early batch one I purchased on 12/22. Its been working great for me. Had no issues with it at all. So it is a hit or miss but odds are in favor of finding a good one.
Good luck on your decision. I'd say keep your prime if it works well for you. Its not a matter of if its as good as it gets. What you described your device as is a really good working one. Why take risk n get rid of it.
I don't think there are any "good ones", specially if Asus has to make a physical hardware change. UNLESS they are already manufacturing this change into production already, but I highly doubt that. A company like Asus could never move that fast.
The WIFI will always be an issue to some, and not an issue to most people. If you happen to be near a router (less than 50-75 feet away) you will be in good shape. If you are in a place like a school or office building where there are many routers, you will be in good shape. If you are trying to hold on to the edge of your routers max range, you will be in bad shape.
for GPS,
people are trying to get a lock with out a data connection. These tablets use the same GPS chip a cellphone would meaning it needs data connection for an accurate lock. You will NOT get an accurate lock using the GPS outside with no data connection. This is how all mobile devices are.
Thanks for the replies. I will sleep on it and decide tomorrow. I also have hopes that Asus will eventually do the right thing and replace the back of the prime...
Prime/Tapatalk
jflaplante said:
Thanks for the replies. I will sleep on it and decide tomorrow. I also have hopes that Asus will eventually do the right thing and replace the back of the prime...
Prime/Tapatalk
Click to expand...
Click to collapse
With what, plastic? That is probably what is going to happen....
I have owned (and still own) ONE Prime. It works great. Wifi is strong or perhaps even stronger than any of my other devices in the house. I own a Playbook, Slider, Evo 3D, Photon, and some other random wifi devices. I was not even aware that there *was* an issue with the Prime and wifi until I started reading posts here with all of these issues and blaming the backing..etc.
I still truly believe that it is environment over the actual device. Wifi is a signal that must pass through walls, etc. I can bet there are times that the overly paranoid Prime owner sees his bar go down one notch and immediately posts up here that he is experiencing the famous "wifi problem". I do not doubt there are some people out there with real problems (such is the nature of electronics manufacture), but I also do not doubt that people overreact when they *think* its a "known problem".
No, I really like the spun metal back, and I'll be pissed if it gets reduced to plastic because of some kind of nonsense. Actually, I won't be THAT pissed...as I already own it
@zektor,
I was thinking more like the current aluminium design which is rigid and resistant but with plastic "windows" at the right places for maximal signals reception. A little like the iPad's solution.
I'm also learning to live without 3G built-in with my sgs wi-fi tether but that another story.
MarcMaiden said:
for GPS,
people are trying to get a lock with out a data connection. These tablets use the same GPS chip a cellphone would meaning it needs data connection for an accurate lock. You will NOT get an accurate lock using the GPS outside with no data connection. This is how all mobile devices are.
Click to expand...
Click to collapse
Sorry, but this simply isn't true.
I very frequently use GPS on my Android phones for GPS navigation when traveling overseas, and most of the time I am not using mobile data due to the exorbitant cost when roaming.
This would not be possible without an accurate lock.
Regards,
Dave
Sent from my GT-N7000 using Tapatalk
Assisted GPS, using a wifi or 3G signal to assist the GPS location only allows a slightly faster location fix. After the GPS gets a location fix, it's not used at all. GPS signals from the satellites are very weak, and metal and water will block them. If you're inside, you simply can't get a good GPS signal. Moving a few feet one way or another can make a big difference, but not always. Being outside is essential for getting a good GPS signal. It's also essential that you don't put your hand over the antenna, because the water in your hand can completely block the signal. Holding the tablet in any position other than horizontal, facing straight up, can also degrade the signal, since the metal case blocks it. Putting a metal case over a GPS antenna is a bad idea, and after Asus did it, they had to decide whether to keep the metal case or make the GPS more usable. Fortunately, IMO, they decided that the metal case was more important than the GPS, so they just dropped the GPS specs from the Prime. Asus does not guarantee that the GPS in the Prime will work at all. However, the latest update, .15, seems to help the GPS reception a lot.
Sent from my Transformer Prime TF201 using Tapatalk

Turned around, bent over again.

Got my RMA back today. I almost didn't even try it, but had to. First of all, there were finger prints all over it. The bastards don't even clean their own products when sending them back. The little plastic pieces that go into the docking holes and the power hole were gone. No where to be found. I found a couple small nicks on the back plate. What a shame. Now for powering it on. I got the Android dude with the red exclamation mark in his belly. Powered off, powered back on. Turned on normal. Had ICS on it but needed .21 installed. No big deal, installed it. My normal speedtests without BT are 30+ all the time. I was able to get that without BT. I made an active BT connection and played some music. Did a few more speed tests and it dropped my speed down to 10-12Mbps/sec. It went from 30+ Mbps/sec to 12Mbps/sec and this is a fixed tablet. They also didn't even mention or look at my multiple dead pixels on the screen. They are very easy to see, so the screen was never replaced. All in all I'm actually in worse shape then I was before. I will try to return this tablet tonight and be done with it. I still have one, with a broken wifi/bt but it doesn't have any nicks or dead pixels.....................yet.
That's a bummer about the RMA experience. I think ASUS needs to take a look at their service partner and knock some heads...
About the wifi/BT thing, I'm still a bit confounded. I've now compared three other Android devices against my Prime, and here's what I've discovered when I stream music via Google Music to my Motorola headphones:
1. ASUS Transformer (TF101): Wifi dropped from about 20Mb/s to about 4MB/s. Better than the Prime, but still a significant impact.
2. Samsung SGS II Epic 4G Touch: Wifi drops from about 20Mb/s to less than 200Kb/s. Very similar results to the Prime, and nothing else can be done while the music is streaming (e.g., can't even browse).
3. Motorola Photon: Wifi drops from about 20Mb/s to around 6Mb/s. Much like the OG Transformer, a significant impact but still usable.
I must be really unlucky in purchasing devices from a variety of manufacturers that all have their wifi impacted by simultaneously streaming to BT. But if yours is dropping from 30+ Mb/s to 10-12Mb/s, you're not experiencing any worse performance than some other devices that I've personally tried. Doesn't seem like such a terrible thing, unless in spite of the fact that you're still getting 10+ Mb/s bandwidth you can't actually use wifi for anything...
wifi bluetooth signal drop is caused because the system is using the same chip for both wifi and bluetooth. Devices that have seperate chips and antennas for wifi and bluetooth will have little or no difference.
Unfortunately, to save space and cut costs most vendors go with integrated wifi/bluetooth chips just becasue its easier.
i very frequently stream music from my SGS2 to my bluetooth headphones while browsing the internet, in fact my wifi and bluetooth are nearly always on and i've never missed the difference. Maybe im just used to slow speeds, who knows

WIFI test

I have heard and read a lot for ASUS TP's WIFI issues. I just got mine TP. With routine tasks I didn't find any WIFI issues. Is there some robust test/check I can do to check for any WIFI issues?
wintablet said:
I have heard and read a lot for ASUS TP's WIFI issues. I just got mine TP. With routine tasks I didn't find any WIFI issues. Is there some robust test/check I can do to check for any WIFI issues?
Click to expand...
Click to collapse
There has been a very vocal group complaining about WiFi issues. I don't know if its just because I have a later version (I've had mine about a month now) or different circumstances or what. I think the latest ones are the one's with serial numbers beginning with C5. Mine is a C4 but like you I haven't had any significant problems. If you find its working well for you, then why worry? Just enjoy it.
Just some observations;
Sitting in my office I have a Dell E6400 laptop, my Prime, and my Droid 3 all sitting side by side. Now, this particular location is a place where all devices have a weak signal. It's also in an area that's bombarded with wireless networks. Between this office building, the coffee shop across one street, and the apartment building across the street, I can detect a total of 26 different SSID's. Almost all of those with pretty weak signals. So sitting here here in a basically worst case location, the Dell laptop definitely gets a faster connection than the Prime or the Droid 3. In terms of speed from fastest to slowest it is Laptp, Prime, and Droid 3. The laptop stays connected all the time. The prime is mostly connected but occasionally fades out, and the Droid 3 fades out a lot. So among my devices the Prime is middle of the pack in this worst case environment. However if I move just a little closer to the router (getting around the bank of metal file cabinets that separate my desk from the router) all three devices work fine.
So my general observation is that when receiving a reasonably good signal, the prime is as good as anything else. In poor conditions it's not as good as the laptop but still usable.
Just my 2 cents worth...

[Q] Signal loss - Death Grip

Alright, I read the review on this phone and, after having the GalaxyS 1, I thought trying an HTC would be a great idea as my GS1 had extreme screen burn in; which led me to opt for an HTC instead of GS2 - the cheaper alternative of course.
I was pretty happy with this phone. Somewhat smaller than what I expected, though it runs fairly well with ICS and HTC Sense loaded.
Now the ridiculous issue. This phone has a severe case of 'death grip'. I've had quite a couple of frustrating weeks trying to figure out what on earth was causing the signal to drop completely from 2 or 3 bars to dead, when picking the phone up to text.
Before I considered googling 'hand signal absorb htc', or similar keywords to that effect, I tested my theory by holding the phone at the top two edges and then in my palm again; in the same position both times. The result? 5 bars to two bars, or even in some cases one bar. The signal where I live isn't excellent, however it's not terrible either. With my GS1 having no issue with signal drops. Just holding the Desire X in the palm of my hand, under the table results in complete signal loss.
This is an absolute joke. I've missed really important phone calls and the majority of sms's arrive late due the lovely signal loss regain repetition, essentially causing the phone do not receive calls, even though, provided it does have 3 or so bars.
So, am I the only one here who has this issue, or for that matter; a faulty phone? Really Really disappointed.
I do have a signal drop problem as I already wrote on another post and nobody answer:
"I have a lot of signal drops on GSM/EDGE and also 3G/HDSPA? The signal is full but, the phone is in stand by, the signal drops and I loose calls. Does anyone have this problem?
Also I noticed when the phone switches from 3G to GSM/EDGE first I have a no signal period (couple of seconds)."
I also had this problem with an LG Optimus 2x when updated to Android 4.0.4.
Dal2000 said:
Alright, I read the review on this phone and, after having the GalaxyS 1, I thought trying an HTC would be a great idea as my GS1 had extreme screen burn in; which led me to opt for an HTC instead of GS2 - the cheaper alternative of course.
I was pretty happy with this phone. Somewhat smaller than what I expected, though it runs fairly well with ICS and HTC Sense loaded.
Now the ridiculous issue. This phone has a severe case of 'death grip'. I've had quite a couple of frustrating weeks trying to figure out what on earth was causing the signal to drop completely from 2 or 3 bars to dead, when picking the phone up to text.
Before I considered googling 'hand signal absorb htc', or similar keywords to that effect, I tested my theory by holding the phone at the top two edges and then in my palm again; in the same position both times. The result? 5 bars to two bars, or even in some cases one bar. The signal where I live isn't excellent, however it's not terrible either. With my GS1 having no issue with signal drops. Just holding the Desire X in the palm of my hand, under the table results in complete signal loss.
This is an absolute joke. I've missed really important phone calls and the majority of sms's arrive late due the lovely signal loss regain repetition, essentially causing the phone do not receive calls, even though, provided it does have 3 or so bars.
So, am I the only one here who has this issue, or for that matter; a faulty phone? Really Really disappointed.
Click to expand...
Click to collapse
Sounds like a faulty antenna. Either that or you have lead hands.
It should be a cheap fix at any local repair shop or free if you take it back to the shop for a replacement.
Sent from my Nexus 10 using XDA Premium HD app
vogonpoetlaureate said:
Sounds like a faulty antenna. Either that or you have lead hands.
It should be a cheap fix at any local repair shop or free if you take it back to the shop for a replacement.
Sent from my Nexus 10 using XDA Premium HD app
Click to expand...
Click to collapse
What I don't understand is, when i'm on an actual phone call, there's no issue with quality or signal loss. Sounds like the phone rom is preserving the antennas power in idle mode?

Categories

Resources