Related
Hello everybody
The new ICS update for the ROGERS EVO 3D just came out yesterday, so I restored my phone to the original firmware (via restoring the backup I did in the recovery) and then proceeded to download the OTA update. After it finished, the phone rebooted into the recovery (i have 4-ext touch recovery) and started installing. After it finished, the phone rebooted and then got stuck on the white HTC screen. I managed to enter the recovery again and restore the original firmware again. What is that I'm doing wrong here? Here is some helpful info:
Rogers EVO 3D, GSM version
Unlocked bootloader (HTCDEV method), S-ON
carrier unlocked
HBOOT 1.49.0008
OS is rooted
I'm in the same boat but I'm not able to do a recovery. I went through the update process and when the phone rebooted it got stuck on the white htc screen. I can get it into the bootloader menu but when i choose recovery it starts but then i get an error with a pic of the device and the red yield sign. If i choose factory reset it just gets stuck at the white htc. I read some other posts and I saw that having an unlocked bootloader may cause issues with updates so that may be your issue as for me, I'm not sure what I can do. I may just need the actual update file to redo the update but I'm not sure where to find it.
Same here, but I don't get half way through the ota update before I see the red triangle and exclamation mark. Phone will boot into stock recovery (which I would assume you need instead of modded recovery) and the update starts, but doesn't complete. I pull the battery and the phone boots up normally. Just can't seem to get through the update. Could be something to do with being s-off I would guess.
EJ
madmajd said:
Hello everybody
The new ICS update for the ROGERS EVO 3D just came out yesterday, so I restored my phone to the original firmware (via restoring the backup I did in the recovery) and then proceeded to download the OTA update. After it finished, the phone rebooted into the recovery (i have 4-ext touch recovery) and started installing. After it finished, the phone rebooted and then got stuck on the white HTC screen. I managed to enter the recovery again and restore the original firmware again. What is that I'm doing wrong here? Here is some helpful info:
Rogers EVO 3D, GSM version
Unlocked bootloader (HTCDEV method), S-ON
carrier unlocked
HBOOT 1.49.0008
OS is rooted
Click to expand...
Click to collapse
Same problem but whit s-off
I have been predicting that this would happen... ICS failures with non-standard HBOOTs. Good luck.
Probably will have to wait for an RUU or custom.
I'd recommend using the GB ruu to get you back to full stock. Always found Rogers ota updates (possibly all carriers?) won't install if you're rooted or using a custom recovery.
I had to install the ruu via renaming the rom.zip to PG86IMG.zip and copying it to the sd card so that the bootloader would auto flash it. Running the ruu exe tossed up all kinds of errors.
It will put everything back to Rogers stock. After that just setup wifi and do the 2 Rogers OTA updates.
Once in ICS, it's easy peasy to get recovery and root back.
Also, for what it's worth, Go Backup is awesome for going rom to rom and not needing a full backup. Use it on rooted rom, then use it to restore after rooting new rom. Will do all your apk's and everything.
1st post here after years of lurking. Yay.
wikkid said:
I'd recommend using the GB ruu to get you back to full stock. Always found Rogers ota updates (possibly all carriers?) won't install if you're rooted or using a custom recovery.
I had to install the ruu via renaming the rom.zip to PG86IMG.zip and copying it to the sd card so that the bootloader would auto flash it. Running the ruu exe tossed up all kinds of errors.
It will put everything back to Rogers stock. After that just setup wifi and do the 2 Rogers OTA updates.
Once in ICS, it's easy peasy to get recovery and root back.
Also, for what it's worth, Go Backup is awesome for going rom to rom and not needing a full backup. Use it on rooted rom, then use it to restore after rooting new rom. Will do all your apk's and everything.
1st post here after years of lurking. Yay.
Click to expand...
Click to collapse
Alright thanks a lot
Just an update on what I did. I was able to reload the stock gb rom for rogers using the exe file, then I went through the 2 updates that came up when checking and ics is now up and running on my phone. However in my attempts of trying to fix the original problem, I managed to re-lock my bootloader before flashing to stock rom and I had s-on the whole time. hope this help.
i switched to stock like.. a week back?
jus got ota on 4th
i WAS rooted and using juopunutbear's hboot *u can jus get the hboot from their website*
so i jus flashed back stock recovery.. and updated.. and success.. lost root though.. and i was back to stock bootloader..
used the PG86IMG with juopunutbear's bootloader and 4ext recovery.. and flashed cwm supersu.. v0.91 i think.. i dunno.. latest one.. and bam.. im on stock.. rooted.. and works perfectly..
Possible sollution
Maybe try flashing one of the customized ROMs that are based on the latest OTA update. I'm sure Anryl's newest rom is blazing-fast and stable. You can find it in the gsm android development forum and flash it via recovery. Make sure you have the latest 4ext recovery installed, though.
where can a i find that stock rogers rom i modified mine and that might be the reason i get a security failure in hboot. s is on. when i run the ruu file in windows to downgrade i get error 155. when i run the the update from about phone. it locks up with blue android guy and yellow exclamation mark. i remove the battery and she boots fine with no changes.
I am trying to do same. Get stuck on HTC screen. I have S-ON. Was on cobra 2.4 prior.
If anyone can give details on how to fix it, it would be great! Please no saying "install exe". I need to know which exe etc.
just wanted to tell everyone that in order for the ota update to work properly, you need to be running stock unrooted firmware with a locked bootloader. Just relock your bootloader, reinstall the stock firmware, upgrade to ics via ota, then re-unlock and re-root.
Hi
I have a HTC EVO 3D from Rogers that was got messed up during changing networks... rooted the phone for no apparent reason... to now get a update for it for ics from the provider and it bricked the phone.
It's stuck at HTC boot screen, can get fastboot USB from bootloader. recovery gets a ! in a triangle and factory reset doesn't work, freezes at splash screen after restarting the phone. Was stupid not making a backup or searching for programs to back it up before I went ahead and clicked update
It has HTC boot-loader 1.49 s-on but is rooted.
I am looking for clear(fix my evo for dummies) step by step instructions with correct installation for my model of phone, HTC EVO 3D Rogers GSM, or anything that could replace the os to get my phone to be useful again I'm currently using my backup phone a HTC G1 HTC ftw
Try kingcobra's rom, ota from rogers will not boot due to the fact that your phone is rooted, kingcobra's rom is based on rogers ota, flash it and leave it.
Sent from my HTC EVO 3D X515m using xda premium
Davideichler7 said:
Hi
I have a HTC EVO 3D from Rogers that was got messed up during changing networks... rooted the phone for no apparent reason... to now get a update for it for ics from the provider and it bricked the phone.
It's stuck at HTC boot screen, can get fastboot USB from bootloader. recovery gets a ! in a triangle and factory reset doesn't work, freezes at splash screen after restarting the phone. Was stupid not making a backup or searching for programs to back it up before I went ahead and clicked update
It has HTC boot-loader 1.49 s-on but is rooted.
I am looking for clear(fix my evo for dummies) step by step instructions with correct installation for my model of phone, HTC EVO 3D Rogers GSM, or anything that could replace the os to get my phone to be useful again I'm currently using my backup phone a HTC G1 HTC ftw
Click to expand...
Click to collapse
Go to the gsm development forum and download the RUU for the phone, and restore it to stock unrooted OS. Before you do that though, make sure that your phone's BOOTLOADER IS LOCKED. Look up how to re-lock your bootloader. After you relock your bootloader, you can proceed with restoring the phone.
Soooo.... basically, what I'm getting from this is, if you like having a locked bootloader, CWM and root, don't bother trying to install this OTA update because it's a headache. Agree?
The phone's not mine, it's my wife's, and she doesn't want anything special or like the idea of me messing around in her phone.
I was about to install this late last night, just about to hit that button, then I thought, "what about the bootloader? what about root? what about the fact that it's now unlocked and being used on a carrier other than Rogers?"
Hello,
Right, I am aware that I've probably made a huge mistake, but I thought, "hey, warranty void because of my screen, why not?", but I have searched and searched and was up until three this morning trying to find a solution, but I only kept getting confused (bare in mind I'm only sixteen).
I rooted my phone using the HTCDev method, and flashed the LoLic Sense ROM, it worked and I turned my phone back on and it got stuck on the bootscreen. So, I downloaded the RUU and tried to go back to stock, and it kept failing. I even tried the PG86IMG.zip and even that didn't work. So, I downgraded to the LEEDroid ROM that came with the revolutionary package I'd used before the official update to ICS, and now I can't even get past the initial HTC screen.
Please can anybody help me get back to stock on my phone? I've managed it before, but this time I keep seeming to come up short.
Thank you
EDIT:
I'm on HBOOT 1.53.0007 - after updating to the official ICS.
I've tried downgrading using the Gingerbread RUU and it won't install on the phone. I can't S-OFF using the wire trick because I'm afraid to break it even more.
I've tried flashing the rooted GB zip in clockworkmod and it says its installed, but I can't turn the phone on and it only gets to the first white HTC screen and then turns itself off.
I'm terrified that I may have broken my only phone and I don't know what to do, please can somebody help me?
If you are S-ON HTC Dev unlocked you need 4ext with smartflash or fastboot flash boot boot.img to install the kernel.
Okay, so I'm in a bit of a bind. I'm S-OFF, and I tried updating to the global leak and it seems I've lost boot and recovery. Everytime I boot it goes through the splash screen and then a black screen with the phone and green update symbol, then it turns to a red triangle and exclamation mark. any help would be greatly appreciated. I'm fairly experienced and everything i've tried has failed. I tried going into hboot and flashing the PH98IMG again. It took, but still the same result. I tried flashing the recovery in fastboot but it continues to fail, and I also tried flashing my boot.img but it also failed. Any ideas?
tomtripp21 said:
Okay, so I'm in a bit of a bind. I'm S-OFF, and I tried updating to the global leak and it seems I've lost boot and recovery. Everytime I boot it goes through the splash screen and then a black screen with the phone and green update symbol, then it turns to a red triangle and exclamation mark. any help would be greatly appreciated. I'm fairly experienced and everything i've tried has failed. I tried going into hboot and flashing the PH98IMG again. It took, but still the same result. I tried flashing the recovery in fastboot but it continues to fail, and I also tried flashing my boot.img but it also failed. Any ideas?
Click to expand...
Click to collapse
unlock the bootloader and flash a recovery. you need to unlock since you dont have eng commands.
btw this belongs in q&a
antp121 said:
unlock the bootloader and flash a recovery. you need to unlock since you dont have eng commands.
btw this belongs in q&a
Click to expand...
Click to collapse
Thanks I'll give that a try. Will the firmware and ROM still be in place? Will I have do the update again? BTW Sorry for posting it in the wrong section..
tomtripp21 said:
Thanks I'll give that a try. Will the firmware and ROM still be in place? Will I have do the update again? BTW Sorry for posting it in the wrong section..
Click to expand...
Click to collapse
Its OK. And once you unlock, it'll reboot. Then you just go back into the boot loader and flash a recovery with fast boot.
Sent from my aokp_tenderloin using Tapatalk 2
So got the recovery flashed, but now it only boots into the recovery.
tomtripp21 said:
So got the recovery flashed, but now it only boots into the recovery.
Click to expand...
Click to collapse
Did you try flashig a rom?
Sent from my aokp_tenderloin using Tapatalk 2
i tried to restore my backup that didn't work, I haven't tried a new ROM yet. I'll try that and get back to you. Thanks again for all your help.
antp121 said:
Did you try flashig a rom?
Sent from my aokp_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
Tried flashing a ROM, the stock deodexed rooted 4.03.605.02. Still boots to recovery...
tomtripp21 said:
Tried flashing a ROM, the stock deodexed rooted 4.03.605.02. Still boots to recovery...
Click to expand...
Click to collapse
You need to use interface to fastboot boot.img then run firmware update for old firmware n old CWR. BASICALLY GO BACK TO STOCK REZOUND N START THE WHOLE PROCESS OVER LIKE DAY 1!
Good news is you don't need to do the wire trick again. Your phone crashed during the firmware upgrade now its stuck in limbo n doesn't know how to handle the 2 sets of hardware commands its receiving from the CMOS.
[Q] Can only get into recovery after attempting Juopunutbear S-OFF
I wanted to S-OFF after being stock locked, with the OTA ICS update. I performed HTC dev unlock successfully. After that, I may have gone wrong during one of several steps.
-Pushed AmonRa recovery 3.15 to my phone (seemed to be successful)
-Flashed ICE-EnableRoot.img (got an error message saying it was unsuccessful, but when I rebooted my phone, SuperUser was installed).
-Flashed vigorOTAStockRooted.zip (because I wanted to try the S-OFF method from stock GB rom)
-Ran HTC Rezound S-OFF Kit By Hasoon2000
-Made sure HTC Drivers were installed
-Enabled USB Debugging
-Put in blank SD Card
-Run Juopunutbear v.6 If You Are On Gingerbread
After running Juopunutbear v.6 for Gingerbread, my phone screen went blank and HTC's splash screen came up momentarily, and then my phone screen went dark. The cmd box that popped up then gave me an error message saying I had to install the HTC Drivers. I went to HTC's website to download the drivers. When I tried to install them, I was told they were already installed.
I can reboot my phone into Hboot and AmonRa recovery and I can do anything from there. But when I try to start my phone, I get the HTC splash screen and then black screen. The orange LED lights up when my phone is powered off and plugged in via USB. When I try to boot from Hboot, I either get a static HTC splash screen or splash screen going to a black screen.
This is what my Hboot screen reads:
*** TAMPERED ***
*** UNLOCKED ***
VIGOR PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
Open DSP-v13.6.0.7611.00.0104
eMMC-boot
Apr 12 2012,16:47:46
Any advise would be greatly appreciated! Thank you!
jtayag said:
I wanted to S-OFF after being stock locked, with the OTA ICS update. I performed HTC dev unlock successfully. After that, I may have gone wrong during one of several steps.
-Pushed AmonRa recovery 3.15 to my phone (seemed to be successful)
-Flashed ICE-EnableRoot.img (got an error message saying it was unsuccessful, but when I rebooted my phone, SuperUser was installed).
-Flashed vigorOTAStockRooted.zip (because I wanted to try the S-OFF method from stock GB rom)
-Ran HTC Rezound S-OFF Kit By Hasoon2000
-Made sure HTC Drivers were installed
-Enabled USB Debugging
-Put in blank SD Card
-Run Juopunutbear v.6 If You Are On Gingerbread
After running Juopunutbear v.6 for Gingerbread, my phone screen went blank and HTC's splash screen came up momentarily, and then my phone screen went dark. The cmd box that popped up then gave me an error message saying I had to install the HTC Drivers. I went to HTC's website to download the drivers. When I tried to install them, I was told they were already installed.
I can reboot my phone into Hboot and AmonRa recovery and I can do anything from there. But when I try to start my phone, I get the HTC splash screen and then black screen. The orange LED lights up when my phone is powered off and plugged in via USB. When I try to boot from Hboot, I either get a static HTC splash screen or splash screen going to a black screen.
This is what my Hboot screen reads:
*** TAMPERED ***
*** UNLOCKED ***
VIGOR PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
Open DSP-v13.6.0.7611.00.0104
eMMC-boot
Apr 12 2012,16:47:46
Any advise would be greatly appreciated! Thank you!
Click to expand...
Click to collapse
For starters, you are on ics firmware so you should run the ics version of juopunutbear. I suggest flashing a rooted Rom based on the ota and then try again.
Sent from my ADR6425LVW using Tapatalk 2
topgun1953 said:
For starters, you are on ics firmware so you should run the ics version of juopunutbear. I suggest flashing a rooted Rom based on the ota and then try again.
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
I successfully flashed one of the stock ICS ROMs! What got me all confused to begin with was the prerequisite that I had to be on a stock Gingerbread ROM or the 3.14.605.5 ICS leak. That's why I tried flashing the original Vigor GB ROM on my phone. I still want to get S-OFF, but I need to read the instructions more carefully. Thanks for your help!
dragonstalker said:
You need to use interface to fastboot boot.img then run firmware update for old firmware n old CWR. BASICALLY GO BACK TO STOCK REZOUND N START THE WHOLE PROCESS OVER LIKE DAY 1!
Good news is you don't need to do the wire trick again. Your phone crashed during the firmware upgrade now its stuck in limbo n doesn't know how to handle the 2 sets of hardware commands its receiving from the CMOS.
Click to expand...
Click to collapse
So I just need to flash my backed up boot.img, and then flash the 3.14.605.12 RUU? Then re-root and retry the OTA Global Update?
tomtripp21 said:
So I just need to flash my backed up boot.img, and then flash the 3.14.605.12 RUU? Then re-root and retry the OTA Global Update?
Click to expand...
Click to collapse
pretty much. From looking at everything looks like you are on ICS, but its not letting you reprogram. usually happens when an update fails. When you run Juonobear and run the ics upgrade over again, it should reboot like 3 or 4 times. Sounds like you never let the process finish. Final note, i'm not sure where you got your firmware from, but your radios do not look familiar. Not saying they are wrong, just not radio's i've ever seen flashed. BUT, I don't usually change radio's unless there is a huge need for it. you should be on radio's 10r/08r that come with the original ICS firmware update. I'll watch the thread throughout the day to lend support where I can. Hope this helps.
dragonstalker said:
pretty much. From looking at everything looks like you are on ICS, but its not letting you reprogram. usually happens when an update fails. When you run Juonobear and run the ics upgrade over again, it should reboot like 3 or 4 times. Sounds like you never let the process finish. Final note, i'm not sure where you got your firmware from, but your radios do not look familiar. Not saying they are wrong, just not radio's i've ever seen flashed. BUT, I don't usually change radio's unless there is a huge need for it. you should be on radio's 10r/08r that come with the original ICS firmware update. I'll watch the thread throughout the day to lend support where I can. Hope this helps.
Click to expand...
Click to collapse
Now I'm a little confused, sorry. I need to run the juopunutbear program again? My radios are 2.22.10.0801r/2.22.10.0803r, Hboot 2.27. I'm downloading the .12 RUU from Android Police. I've tried re-flashing the boot.img from my nand backup, but it keeps saying:
C:\mini-adb_vigor>fastboot flash boot.img
unknown partition 'boot.img'
error: cannot determine image filename for 'boot.img'
edit: I fixed the flash, I forgot to add the partition in the command, duh... So I flashed my backed up boot.img, now I just need to flash the .12 RUU?
I have the backup img in the file where I have fastboot, adb, etc.. What am I doing wrong?
tomtripp21 said:
Now I'm a little confused, sorry. I need to run the juopunutbear program again? My radios are 2.22.10.0801r/2.22.10.0803r, Hboot 2.27. I'm downloading the .12 RUU from Android Police. I've tried re-flashing the boot.img from my nand backup, but it keeps saying:
C:\mini-adb_vigor>fastboot flash boot.img
unknown partition 'boot.img'
error: cannot determine image filename for 'boot.img'
edit: I fixed the flash, I forgot to add the partition in the command, duh... So I flashed my backed up boot.img, now I just need to flash the .12 RUU?
I have the backup img in the file where I have fastboot, adb, etc.. What am I doing wrong?
Click to expand...
Click to collapse
I have now tried to flash the .12 RUU in Hboot but it will not flash it, probably because my firmware is newer right? Back to the drawing board....
Still to no avail I am getting nowhere. I flashed the stock recovery and did a factory reset from Hboot. Nothing, I have tried flashing the newest RUU, nothing, I'm flashed back to ra-recovery. Can anybody give me a solution step by step to get a ROM loaded and booting?
Well I finally got it up and working. I loaded the old firmware and was able to restore by backup. Thanks to all who chimed in with helpful advice. I'm hesitant to retry the Global update, but I might go ahead and give it another shot.
Glad you figured to restore the firmware. It's not hard to flash the global. Run the firmware, then run the recovery then flash Rom. Do it right in that order n you don't have any issues. Use 2 sdcards if you need to because the firmware upgrade won't delete the ph98 off your card. You will need to do it manually.
Sent from ICS REZOUND S-OFF
So I have a problem with my phone randomly rebooting, so I am trying to run the stock RUU to make sure it is nothing I did. The problem is that when I do this I get to the step were the phone is supposed to go to the bootloader and it just shows a black screen with the HTC logo. Any idea what I should try next?
Have you re-locked your bootloader and installed a stock recovery?
How do I do that without the ruu
Sent from my EVO using xda app-developers app
You have to be re-locked for the RUU to work.
fastboot oem lock
Try this script thanks to viperboy
http://forum.xda-developers.com/showthread.php?t=2197909
Good luck!
Sent from my EVO using xda app-developers app
The script hangs at starting ruu mode
RUU not working on Evo Jewel
kevinb99 said:
The script hangs at starting ruu mode
Click to expand...
Click to collapse
Did you ever figure this out? I have the same problem, and I too have tried the Vipe utility. It does flash the recovery in the batch file, but RUU fails. I have tried all RUU's from androidfiles for the jewel and they fail to with an unknown error. I cannot get any custom roms to flash either, they fail altogether or they flash but never get past they HTC screen. I can still boot into recovery and I have also tried relocking the bootloader.
jseibert81 said:
Did you ever figure this out? I have the same problem, and I too have tried the Vipe utility. It does flash the recovery in the batch file, but RUU fails. I have tried all RUU's from androidfiles for the jewel and they fail to with an unknown error. I cannot get any custom roms to flash either, they fail altogether or they flash but never get past they HTC screen. I can still boot into recovery and I have also tried relocking the bootloader.
Click to expand...
Click to collapse
No, that sucks, I was able to get stock rooted on and have since gotten 5 replacement phones.
Got RUU working
kevinb99 said:
No, that sucks, I was able to get stock rooted on and have since gotten 5 replacement phones.
Click to expand...
Click to collapse
So your problem is with the phone rebooting still? I was having trouble installing the RUU and it seems so have a lot of people. The boot loader does need to be locked, that was one of my problems. I'm also pretty sure I wasn't using the correct RUU, as I tried so many. Vipe doesn't work but will at least push a recovery. I re-locked the bootloader, and tried one last RUU and it worked.
When I tried flashing the phone originally, something went wrong. TWRP wouldn't install any Roms at all even when some completed successfully. It would just hang at the HTC screen. I could probably go back and try it again but I'm done. I won't touch another HTC phone as far as flashing goes.
Ok, I will try to give as much info as I can, please let me know if there is anything else I should provide. I really appreciate any help and advice as I've been pulling my hair out for the last 3 days, spending 10+ hours trying to get my Amaze back working.
Problem started a few days ago, phone shut off, when it powered back on it was stuck on the White HTC logo. That same day the phone died completely and would not power on at all, not even the amber light. Eventually the amber light would blink the but phone wouldn't charge. I fixed this first issue by jump starting the battery with a 9V battery, something someone suggested on a thread. Worked great to get the phone charging again... but that's it. So basically I have access to the HBOOT/Fastboot and EXT4 Recovery menu's, and there is no OS on the phone, I know for sure now because I wiped the system.
When I try (but fail) to install the RUU 1.41 exe, and it checks the phone, i comes back saying my "current" version on the phone is 2.14.661.2 even though there isn't any OS on there...
Bit more background info. I purchased this phone last year off someone, it was running 4.1.2 and the bootloader was unlocked. It *is S-ON though.
Whatever else this guy did, I'm not sure as this is what I can tell, however the CID pulls up as Telus001? which the guy did tell me it was a Telus phone.
So I'm trying to load the Telus stock rom and I've been getting nowhere and pulling my hair out. I'm 10hrs in and no further then I was. So first I downloaded the Telus RUU 1.41 exe from the stock rom but it gives an Error 43. I tried this with both the bootloader locked again, and unlocked. I then downloaded the OTA 2.14.661 zip from the stock roms, and renamed it to PH85IMG, stuck that on the Ext SD card. Problem is when it boots into the HBOOT it actually see's the file, loads it, then checks it, but then returns me to the main menu. I don't get promted to update. Now I've tried this too with the bootloader unlocked, and locked. So a third go, I extracted the Rom from the 1.41 RUU and made that PH85IMG, tossed it onto the SD card and again this time it actually went further but gave another error.
I have tried to Sideload the above Roms through recovery but they give error's.
In that All In One program there is an option to fix the Mainver error, however when I run that all I get is "Device not found". The phone IS loaded under device manager as HTC Phone as I had installed the drivers. I've tried to google this fix but I can't get anywhere.
Everyone has said on forums that sticking a PH85IMG.zip file on an Ex SD and having it boot into the HBOOT menu will rebuild the phone, but I'm out of idea's how to get there because it loads the rom's, checks them, and then boots me back to the menu. There is only 2 Rom's I can find for Telus, and that's the 1.41 EXE or the OTA 2.14.661.2. My HBOOT version is 1.93.0002, RUBY PVT SHIP S-ON RL.
Thanks in advance for any help/suggestions, desperately just want my phone working again. I feel like I've been to the 4 corner's of google trying to solve this problem.
Strange This should not happen.Also if your phone is running 4.1.2 which should be a custom then that means your phone was updated to ics so the ruu.exe will fail.if you have access to 4ext recovery then you can flash any custom rom to boot your phone.But if you want stock and both of the stock roms for your carrier is not working then the only thing you can do is s-off the phone then use supercid so you can flash any carrier's rom then flash t-mobile ics stock.Tell me if this worked for you.
darkshadow1997 said:
Strange This should not happen.Also if your phone is running 4.1.2 which should be a custom then that means your phone was updated to ics so the ruu.exe will fail.if you have access to 4ext recovery then you can flash any custom rom to boot your phone.But if you want stock and both of the stock roms for your carrier is not working then the only thing you can do is s-off the phone then use supercid so you can flash any carrier's rom then flash t-mobile ics stock.Tell me if this worked for you.
Click to expand...
Click to collapse
Got it going!! Thanks for the suggestions. What did it in the end was this thread --> http://forum.xda-developers.com/showpost.php?p=27058110
I had EXT4 Recovery already, so I used his Zip and just flashed that. Phone came back up and is running great now... if only I had found his thread before the hr's and hr's I've been googling and trying things.