Guys
I flashed a ROM from Spain using Odin (I9300XXDLIH, 4.2.1 from Samfirmware) into my S3 (GT-I9300 bought in Brazil) and it works by 1 month. Then my phone starts to crash or boot by itself and finally it stop boot into Samsung screen.
I have access to Download screen, but I have NO access to recovery screen.
Now, I tried to flash a new ROM and Odin says that it has no partition. The phone doesn’t charge anymore (I need to charge using a friend’s phone).
I tried flash an old version (4.0.4) but every time I get “no PIT partition” from Odin. I also tried to flash from different version of Odin and same results.
Is there any way to solve this without getting a Service Center? Here in Brazil is difficult to find JTAG service, so I need some home solution.
Thanks and sorry for my English.
Hi, mines went exactly the same as that last week, tried everything possible software wise. sent it to samsungs ext service centre in scotland. i still dont know fr sure if there goni fix it under warranty as in download mode it says official Rom but it also says custom system. Theyve had it since last tuesday and on the repair status it still says "Acknowledge(ASC)"
heres hoping, and i hope u get urs sorted
Please feel free to find the Sudden Death thread in General section.
spamtrash said:
Please feel free to find the Sudden Death thread in General section.
Click to expand...
Click to collapse
Hi spamtrash,
As I can understand, that thread is to prevent. Now I need to recovery.
I just tried to flash a new ROM again, and I get the following:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBDLJ1_I9300UBDLI2_I9300ZTODLJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the first time I get that. The SetupConnection took a lot of time.
I tried to flash PIT file (do not know if it is the right PIT) and get Fail instant.
Any other help. Thanks to all.
Edit:
Now, I turned off and on again and tried to flash the same ROM:
<OSM> I9300UBDLJ1_I9300UBDLI2_I9300ZTODLJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009>
<ID:0/009> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
It says no PIT partition.
Finally, I tried a PIT:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
thats mine when i try write PIT file to my phone
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
and when i try flash CWM here:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
any suggestion
Anyone flashing a PIT file unless 100% correct is asking for trouble .
Buy a new motherboard .
jje
if theres an error in the emmc flashing the original pit file is unduly. the first thing you need is to flashing recovery to see if its working or not then there solutions such as blocking or disabling the corrupted areas in the emmc chip.
Guys,
Thanks for helping but I guess the phone is briked. I will trie the service center.
Related
Ok so after looking everywhere for a solution and screaming like a mad man in the process i decided to make a thread here and see if someone can help me.
I was running the leaked Android 4.0.3 (got the files from software2tech.com/2012/01/26/complete-guide-update-android-4-0-3-i9100xxlp6-for-samsung-galaxy-s2-video/) and i was running fine. Now i decided to root my phone using software2tech.com/2012/01/27/how-to-root-samsung-galaxy-s2-android-ics-4-0-3-i9100xxlp6/#more-16920
When Odin restarted my Phone all i got was that yellow triangle and i wasn't able to do anything at all but go into download mode (recovery mode is not working) so i thought i could just flash the 4.0.3 Android again and it will all be fine right?....WRONG. Got an error in Odin and after that my phone just said "Firmware Upgrade encountered an error. Please select recovery mode in Kies and try again". Tried it but Kies is not recognizing my phone (neither on the "Firmware upgrade error" screen nor in download mode).
Tried Pistachios Recovery guide but the recovery is not working...i can flash the kernel (which sends me back to the yellow triange) but when i try to flash the recovery files or the bootloader i just get more errors. Also read that flashing a stock kernel could be able to fix a problem like this but how am i supposed to find out what my kernel version is, and choose the right one for my phone if i can't start my phone?
Edit: Ok so here are the errors i get when i try to flash
Recovery files:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9100XXKI3_CL577579_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXKI3_REV_02_CL1062028.tar.md5 is valid.
<OSM> GT-I9100-CSC-MULTI-OXAKI3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Bootloader:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> Sbl.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
PS: My Provider is Alice
bump bump bump
tried with stock files....error
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> param.lfs
<ID:0/003> zImage
<ID:0/003> boot.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
tried the stock files again with the recovery kernel as pda (yeah probably not a good idea but i'm at the point where i don't really care anymore) got this error
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003>
<ID:0/003> Receive Response form LOKE
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Miigi said:
Ok so after looking everywhere for a solution and screaming like a mad man in the process i decided to make a thread here and see if someone can help me.
I was running the leaked Android 4.0.3 (got the files from software2tech.com/2012/01/26/complete-guide-update-android-4-0-3-i9100xxlp6-for-samsung-galaxy-s2-video/) and i was running fine. Now i decided to root my phone using software2tech.com/2012/01/27/how-to-root-samsung-galaxy-s2-android-ics-4-0-3-i9100xxlp6/#more-16920
When Odin restarted my Phone all i got was that yellow triangle and i wasn't able to do anything at all but go into download mode (recovery mode is not working) so i thought i could just flash the 4.0.3 Android again and it will all be fine right?....WRONG. Got an error in Odin and after that my phone just said "Firmware Upgrade encountered an error. Please select recovery mode in Kies and try again". Tried it but Kies is not recognizing my phone (neither on the "Firmware upgrade error" screen nor in download mode).
Tried Pistachios Recovery guide but the recovery is not working...i can flash the kernel (which sends me back to the yellow triange) but when i try to flash the recovery files or the bootloader i just get more errors. Also read that flashing a stock kernel could be able to fix a problem like this but how am i supposed to find out what my kernel version is, and choose the right one for my phone if i can't start my phone?
Edit: Ok so here are the errors i get when i try to flash
Recovery files:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9100XXKI3_CL577579_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXKI3_REV_02_CL1062028.tar.md5 is valid.
<OSM> GT-I9100-CSC-MULTI-OXAKI3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Bootloader:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> Sbl.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
PS: My Provider is Alice
Click to expand...
Click to collapse
my friend
if u don't use software from xda forum, why u make posts here. go to software2tech.com and make posts there. u asked us to give a solution to something we never used and we don't know nothing about.
hi
I probably tried loading i9100 rom into my i9100G phone and now its stuck.
I got BSOD (Black Screen Of Death) - see attached jpg.
when i connected the phone back to the pc the odin app recognized it (i guess it remained in download mode).
I loaded the following file GT-I9100G_ICS_ClockworkMod-Recovery_6.0.1.2.tar and by that i coud enter download mode and recovery mode.
I tried to load ROM stock and failed time and again, each time got the same message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLPQ_I9100GODDLP7_I9100GDDLP5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007> factoryfs.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
CAN SOMEONE PLEASE HELP ME TO REVIVE MY PHONE?
Thanks.
itsik888 said:
hi
I probably tried loading i9100 rom into my i9100G phone and now its stuck.
I got BSOD (Black Screen Of Death) - see attached jpg.
when i connected the phone back to the pc the odin app recognized it (i guess it remained in download mode).
I loaded the following file GT-I9100G_ICS_ClockworkMod-Recovery_6.0.1.2.tar and by that i coud enter download mode and recovery mode.
I tried to load ROM stock and failed time and again, each time got the same message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLPQ_I9100GODDLP7_I9100GDDLP5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007> factoryfs.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
CAN SOMEONE PLEASE HELP ME TO REVIVE MY PHONE?
Thanks.
Click to expand...
Click to collapse
hi, did you resolve your problem with your phone? i have the same problem, but with a Galaxy Note. if you done it, can you give me a hand? thanks
adyolcian said:
hi, did you resolve your problem with your phone? i have the same problem, but with a Galaxy Note. if you done it, can you give me a hand? thanks
Click to expand...
Click to collapse
Go to Galaxy Note forum.
Sent from my GT-I9100
boki9999 said:
Go to Galaxy Note forum.
Sent from my GT-I9100
Click to expand...
Click to collapse
And the other guy can go to the Gt-I9100GGGGGGGGGG forum.
I had the same problem and I've flashed a stock ICS rom via odin. And do a factory reset/ cache wipe. After that *2767*3855#. It's a hard reset and you'll lose everything but you can use your phone again
Edi got the same problem. Already tried flash stock 4.0.1 rom. FAILED.
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> boot.bin
<ID:0/028> NAND Write Start!!
<ID:0/028>
<ID:0/028> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What should i do now ?
shinseijuro said:
Edi got the same problem. Already tried flash stock 4.0.1 rom. FAILED.
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> boot.bin
<ID:0/028> NAND Write Start!!
<ID:0/028>
<ID:0/028> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What should i do now ?
Click to expand...
Click to collapse
try to change the port USB, or try it on another PC if you can
if anyone know, is there any way to change the firmware beside ODIN? thanks
shinseijuro said:
Edi got the same problem. Already tried flash stock 4.0.1 rom. FAILED.
<OSM> Leave CS..
<ID:0/028> Odin v.3 engine (ID:28)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Get PIT for mapping..
<ID:0/028> Firmware update start..
<ID:0/028> boot.bin
<ID:0/028> NAND Write Start!!
<ID:0/028>
<ID:0/028> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What should i do now ?
Click to expand...
Click to collapse
This actually happens quite often for me. Just try again and again. You'll get there eventually. Try and do the process as quick possible. That helped me.
Not working. Now my friend cant use his phone and its not even rooted yet! All he wants just a standard pc kies update and kies give him the computer screen.
Now using:
Sony Xperia tipo ST21i
stock 4.0.4
11.0.A.4.22
(rooted, locked bootloader)
Current problem:
Cant get past installing flash drivers in xp.
Hi all,
I am newly registered to the forum, but I have been reading the boards for a while.
I have run into an issue with my phone, in so much that I cant get past the Samsung Boot logo. I cannot get to CWM (Vol up, power and home) but I can get to Download mode (Vol down, power and home).
Once inside Download mode I have tried flashing a few ROMs and they all fail, with a "there is no PIT Partition". so after some google, I found a few PIT files to try to re-partition. These include the MX.PIT and the GT-I9300_mx_20120329.pit. If requested I can upload them for some one to parse thru the PIT_Magic tool.
Once I select the PIT file and select Re-Partition, I get the following error:
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1_
Any one have any tips or words of wisdom to share?
And yes I know don't f**k with it in future.
Shushu13B said:
Hi all,
I am newly registered to the forum, but I have been reading the boards for a while.
I have run into an issue with my phone, in so much that I cant get past the Samsung Boot logo. I cannot get to CWM (Vol up, power and home) but I can get to Download mode (Vol down, power and home).
Once inside Download mode I have tried flashing a few ROMs and they all fail, with a "there is no PIT Partition". so after some google, I found a few PIT files to try to re-partition. These include the MX.PIT and the GT-I9300_mx_20120329.pit. If requested I can upload them for some one to parse thru the PIT_Magic tool.
Once I select the PIT file and select Re-Partition, I get the following error:
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1_
Any one have any tips or words of wisdom to share?
And yes I know don't f**k with it in future.
Click to expand...
Click to collapse
Additionally I tried a multi part flash with PIT and ODIN produces this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALEF_611327_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXLEF_REV02_REV04_CL1147871.tar.md5 is valid.
<OSM> CSC_OXE_I9300OXEALE4_CL606160_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
So I am of the impression I am hosed, but I hope for a response from someone in the know to save my a$$ and phone :fingers-crossed:
So my friend was trying to fix the wifi on his Note while on Sky Rom (4.3), but, for some reason he happened to have clicked a link to the wrong section and was in the n7100 (international) section. He used Odin to flash the MJ5 bootloader which is the international version. Now his phone will only bootloop with the N7100 boot screen appearing. We are not able to access recovery but we can get to download mode. Once we got to download mode I have tried flashing the PIT file, root66, and the official VRAMC3. Each attempt without a PIT file causes this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And any attempts with the PIT file causes this
003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be very much appreciated because I have run out of ideas at this point.
Jet5195 said:
So my friend was trying to fix the wifi on his Note while on Sky Rom (4.3), but, for some reason he happened to have clicked a link to the wrong section and was in the n7100 (international) section. He used Odin to flash the MJ5 bootloader which is the international version. Now his phone will only bootloop with the N7100 boot screen appearing. We are not able to access recovery but we can get to download mode. Once we got to download mode I have tried flashing the PIT file, root66, and the official VRAMC3. Each attempt without a PIT file causes this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And any attempts with the PIT file causes this
003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be very much appreciated because I have run out of ideas at this point.
Click to expand...
Click to collapse
I went through this last month and check these things:
- Try a different USB cord
- Try a different USB port
- Disable your antivirus
- May have to reboot your computer
When I softbricked a few weeks ago I went through this process for the first time, and I found I had to keep trying over and over but it finally ended up working.
Remember to unlock your bootloader after this process - which I did not and had to redo everything after rooting and flashing and getting the Verizon discovered unauthorized software etc.
Also, I wonder if this is part of the issue, while in download mode I get "PRODUCT NAME: GT-N7100" instead of sch-i605, could this be part of the issue?
And thanks for the ideas Darbylonia, I tried those and even different computers and still no luck.
Jet5195 said:
Also, I wonder if this is part of the issue, while in download mode I get "PRODUCT NAME: GT-N7100" instead of sch-i605, could this be part of the issue?
And thanks for the ideas Darbylonia, I tried those and even different computers and still no luck.
Click to expand...
Click to collapse
Did you try looking through the top stickied post about how to recover from a soft brick? I would go there and see if the info helps and post there. I do think it is strange about the product name but there's got to be a fix so keep on...
Hi there,
it's matteios1984 first of all i'd like to say hello to the comunity and thank you all for interesting post about Android!
I'm here to asking help about a tricky case. I've a Samsung Galaxy S3 (i9300) bricked. In other words the phone behaves as follow:
- If i try to turn on the device it remains stuck on Samsung S3 logo
- No possible to boot in recovery mode
- When I connect it to the charger it's stucked showing the battery image and not showing any progress about charging status
- The device is still able to boot in download mode both with buttons combo and with resistor trick, but Odin is not able to flash anything on the device (my idea is to flash a Customer Recovery, perform a full wipe of the device and after restore original italian firmware)
Here following a log taken from Odin:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
If i try to flash a file containing PIT informations here following the log from Odin:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I've heard about the possibility to boot the device by a MicroSD card that allows me to flash the device... Do you think this will fix my issue? Or do I need a box? If so, any suggestion about the model is appreciated.
Thanks in advance for your support
Try downgrading the bootloader to BLFB before flashing firmware or pit.