"Unfortunately Setup Wizard has stopped working" - after trying to install Gapps
So I've successfully managed to get the current CM nightly on my S2, after a few trials and tribulations.
I'd left my phone alone for a bit, all working fine.
Then I decide to get it sorted properly, and install the Google Apps.
Googling told me to use the 20120429 version. So I downloaded that (using the phone's browser), went into CWM and installed it. No joy.
Silly me, I didn't reset + clear cache. So I did that. Still no joy.
So now I've re-installed CM and done a reset + clear cache.
And still I'm stuck looking at the 'setup wizard stopped working' messages, in an endless soul-destroying loop
What can I do?
Would re-installing a stock rom and then re-rooting do the trick?
I can't get Odin to connect, and so I've copied the zipped 4.0.3 rom into the internal SD card, but CWM fails (is it because it has a .dll file alongside the .tar?)
I'm wishing I'd left the phone alone now
RostokMcSpoons said:
So I've successfully managed to get the current CM nightly on my S2, after a few trials and tribulations.
I'd left my phone alone for a bit, all working fine.
Then I decide to get it sorted properly, and install the Google Apps.
Googling told me to use the 20120429 version. So I downloaded that (using the phone's browser), went into CWM and installed it. No joy.
Silly me, I didn't reset + clear cache. So I did that. Still no joy.
So now I've re-installed CM and done a reset + clear cache.
And still I'm stuck looking at the 'setup wizard stopped working' messages, in an endless soul-destroying loop
What can I do?
Would re-installing a stock rom and then re-rooting do the trick?
I can't get Odin to connect, and so I've copied the zipped 4.0.3 rom into the internal SD card, but CWM fails (is it because it has a .dll file alongside the .tar?)
I'm wishing I'd left the phone alone now
Click to expand...
Click to collapse
What version of CyanogenMod are we talking about here? You need to be more specific.
themadba said:
What version of CyanogenMod are we talking about here? You need to be more specific.
Click to expand...
Click to collapse
Right, maybe I found the cause of the problem - I've installed cm-10.1-20130125-NIGHTLY-i9100 but when I wanted to find out which version of Gapps I needed I couldn't be sure what it was so I decided to just find the original download page again. But somehow I managed to find this page http://get.cm/?device=galaxys2 (a rather too easy mistake to make?) ...which has version 9! So I've tried to install the wrong Gapps file
RostokMcSpoons said:
Right, maybe I found the cause of the problem - I've installed cm-10.1-20130125-NIGHTLY-i9100 but when I wanted to find out which version of Gapps I needed I couldn't be sure what it was so I decided to just find the original download page again. But somehow I managed to find this page http://get.cm/?device=galaxys2 (a rather too easy mistake to make?) ...which has version 9! So I've tried to install the wrong Gapps file
Click to expand...
Click to collapse
I thought you might have! I'm not sure whether a simple flash of the correct gapps file will solve your problem or whether you will need to wipe data/factory reset, wipe cache and wipe dalvik cache, reinstall the CM10.1 nightly and then flash the correct gapps file which can be found here: http://goo.im/gapps/gapps-jb-20121212-signed.zip
Try just wiping your cache and dalvik cache in recovery and flashing the new gapps file I linked, if the flashing process doesn't last for atleast 20 seconds, then you may have to carry out the steps I listed above for a complete reinstall.
themadba said:
I thought you might have! I'm not sure whether a simple flash of the correct gapps file will solve your problem or whether you will need to wipe data/factory reset, wipe cache and wipe dalvik cache, reinstall the CM10.1 nightly and then flash the correct gapps file which can be found here: http://goo.im/gapps/gapps-jb-20121212-signed.zip
Try just wiping your cache and dalvik cache in recovery and flashing the new gapps file I linked, if the flashing process doesn't last for atleast 20 seconds, then you may have to carry out the steps I listed above for a complete reinstall.
Click to expand...
Click to collapse
Thanks but I've now tried the reset / wipes / reinstalls multiple times to no avail. And now when I connect my phone to my pc to try to put the correct gapps zip on there, Windows Explorer is only showing a few of the folders on Internal Storage. The stuff that I've already got at root isn't showing. Have I knackered my phone?
I'm going to have to leave it til the morning - the battery is nearly empty.
Edit: Damn, I couldn't get to sleep without fixing it first, and luckily I did: I rebooted my pc, and the explorer eventually did show the contents ok (just very slowly). I dragged the zip in, installed it with CWM and *huzzah* it's working! The only odd thing is the camera has disappeared from the applications...
I can wait until tomorrow to work that out.
Thanks for your help
RostokMcSpoons said:
Thanks but I've now tried the reset / wipes / reinstalls multiple times to no avail. And now when I connect my phone to my pc to try to put the correct gapps zip on there, Windows Explorer is only showing a few of the folders on Internal Storage. The stuff that I've already got at root isn't showing. Have I knackered my phone?
I'm going to have to leave it til the morning - the battery is nearly empty.
Click to expand...
Click to collapse
That's strange. I recently flashed a wrong gapps file and it led to some things not working, especially the Play Store. I tried just wiping the cache and dalvik cache and flashing, but that didn't work. So I did a wipe data/factory reset, wipe cache and wipe dalvik cache, reflashed the ROM and then flashed gapps. I think I may have wiped the cache and dalvik cache once more for good luck, and then repaired permissions in the advanced section of recovery. Phone booted up fine and all apps worked perfectly. I doubt the phone is knackered, perhaps try and different ROM just to make sure it boots fine, and then try flash CM10.1 again. Good luck
Samsung Galaxy s2 CM10 trouble Setup Wizard has stopped working
Im from Asia and I guess Samsung s2 int’l version has different features. I already updated my firmware to JB 4.1.2 (leaked) and since I am not satisfied with it,I rooted it and installed siyah as well as cm10 + gapps from XDA links. I followed everything according to the posts and vids.The problem is that after rebooting and CM start up showed up,the next prompt was UNFORTUNATELY,SET UP WIZARD HAS STOPPED WORKING. What’s wrong? I have tried 6x times and no one worked correctly. HELP me!
I was under the same problem few days ago...
flashed 4.2.2 gapps on 4.1.2..
and succumbed to 'unfortunately setup wizard has stopped' error, until i flashed the respective 4.2.2 gapps.
but sadly it ate away my internal memory (cant help )
So the point is
just flash the respective gapps
and then the ROM again
Hi I just installed cyangenmod and it works but setup wizard is crashing and I don't know how to fix this my phone its pretty much unusable. Need help urgently!
The key is to wipe regular cache partition after installing Gapp zip! :]
I think you have the key. I get my cm10.1.5 and I flashed a realy slim gapps (11mb), but after that I didn't wipe cache and dalvik. So the phone didn't woke up because it get stucked in the wizzard setup. So I have to do as u said. And like the other said, reinstall the rom and then the gapps.
Galaxy 5
After using android 2.1 update 1 in my samsung galaxy 5 (GT-I5503)
I updated it with 2.2 froyo then 2.3 then 4.0 then 4.1.
last time I updated to 4.2 CyanogenMod
Before that I could work good in others. But in 4.2 there were problem of contacts in SIM card, these contacts not showing in device.
Then after my device not detacting SIM card for last few months.
Now my phone showing "Unfortunately, Setup Wizard has stopped."
How can I start my phone?
Galaxy Grand CM12 error
Hi,
I have succesfully flashed my galaxy grand and installed CM12 as per instructions given. But i am constantly facing issue of "Unfortunately Setup wizard has stopped". I have tried all the methods mentioned, but still facing same.
Pls Help
fixed this error(setup wizard or google play service has stoped).first you must install cm13 after that install your gapps(use phliz toch recovery) then reboot device.you Will notic that device doesn't boot or you'll have the same problem(setup wizard).come back to recovery and install the other recovery(change phliz touch to CWM) then with wipe install the same ROM and after that install gapps.the gapps won't install so reboot the device.enjoy your ROM with gapps
fix
FOR ANY1 facing this problem on cm13 setup wizard stopped.
just do as i say it's actually funny but it worked for me for the very 1st time.
I tried all the fix given like clear cache or flash new gapps but nothing solved the problem.
So just do what i say.
when u see the setup wizard stopped error.
on that screen just touch all the corner of the screen of ur phone
staring from the top left corner then the top right and so to the bottom right corner and then at last the left most corner.
Just keep trying i doesn't happen for the first time.
Most of u would be thinking it's funny but it actually worked just give it a try.
it helped me might work for u as well
---------- Post added at 07:49 PM ---------- Previous post was at 07:43 PM ----------
dkarry said:
Hi,
I have succesfully flashed my galaxy grand and installed CM12 as per instructions given. But i am constantly facing issue of "Unfortunately Setup wizard has stopped". I have tried all the methods mentioned, but still facing same.
Pls Help
Click to expand...
Click to collapse
bro just start your phone and on the screen where u see the error
leave it as it is and do this:
touch the top most left corner twice like tapping on it nad then the right most corner then the right bottom corner then lastly the left most corner.
it helped me might help u as well
sir,
i have samsung galaxy star GT-S5282 model but i am unabble to start the Device because of error of unfortunately samsung setup wizard has stoppeed
Related
So...I can't install either of the two CM based ROM's I've downloaded. However, on the first try, I installed VEGan, and then tonight TNT Lite, with no issues. Any CM ROM I try to install just sits on the loading screen, regardless of how long I wait. Is there something special that needs to be done to install them, different than what I do for other ROM's? (Clear data/cache, flash the ROM, clear data/cache again, reboot.)
sfreemanoh said:
So...I can't install either of the two CM based ROM's I've downloaded. However, on the first try, I installed VEGan, and then tonight TNT Lite, with no issues. Any CM ROM I try to install just sits on the loading screen, regardless of how long I wait. Is there something special that needs to be done to install them, different than what I do for other ROM's? (Clear data/cache, flash the ROM, clear data/cache again, reboot.)
Click to expand...
Click to collapse
I believe you have ClockworkMod 0.8 recovery, since you were able to flash Vegan Rom.
In general, before you flash the different rom
1. Back up your current rom
2. wipe data (factory reset)
3. wipe cache
4. flash the rom
5, flash gapps
6. reboot
Hope this helps
There have also been some reports of G-Tablets coming out of the box with incorrect partitions.
Using NVFlash has cured those issues. You should then be able to flash CM7 Roms through CWM like everyone else.
I repartitioned with 2048/0, shouldn't that rule out any partitioning problems?
I'm trying it again right now with flashing the rom then gapps.zip, waiting for it to boot...or just stay on the boot screen.
Format system and data, then follow those steps again. I ran in to similar issues when I hadn't formatted.
Also, do the three wipes again after installing the ROM and gapps.
Holy crap! I see the CM boot screen now! Thanks for the help guys. Now, do I still need to do the market fix (http://forum.xda-developers.com/showthread.php?t=865245)? It looks like from their changelogs that the latest version of Flash is cooked into the ROM so I shouldn't have to do that part from the guide, but I'm wondering about the market.
Well, the market seems to have everything, including an app (power control plus) that none of the other rom's let me see, so I seem to be good to go! Thanks again guys!
Thanks for the suggestion - and I'll readily admit I'm WAY out of my comfort zone with Android.
When I format the /system /data do I have to mount first?
What order do the steps run in? Do I partition and then format /system /data?
cannot install cm based roms
I was trying to reset from factory rest but failed when my gtablet stucked and apparently did something wrong along the way. Now when I turn it on, I get the 3 birds screen, followed by G-Tabdevs screen, then dead. I do have clockwork mod installed on it.
1 when I clicked factory rest, it just return to the manue and said cannot find the file.
2 when I did a back up, it went through boot image,recovery image,system and then taskbar stopped in the half at settings.apk and then dead.
3 when I tried to followed this link http://forum.xda-developers.com/showthread.php?t=865245
to use the external tf card to flash, Gtablet doesnot recogonize the external card, while I can read all the files in gtablet. I can copya single small file but cannot paste a recovery and update.zip on gtablet. Each time I copied a file from gtablet, then it is dead. I have to return on by pressing power and volume+.
4 I tried adb to push update.zip to gatblet,also failed. I feel my gtablet can only allows me to read it and refuse me to do anything on it.
Any ways to reboot my gatblet brick?
Please help! I've been reading forums all weeks trying to figure out how to fix it and am not having any luck!
Appreciate any suggestions
Hello all,
Sorry that i have to post this out of the thread as i cannot post on the development thread for this rom.
I have a Samsung S2 which is rooted. With the release of Foxhound Revolver Ocelot, i tried upgrading from the previous release Foxhound sniper wolf. However i had this issues with the upgrade. I then also tried fresh install but too had problems, i tried for more than 10 times so this is roughly what i gotten
Steps for Upgrading
1. Went into recovery mode and Wipe cache and also wipe dalvik cache
2. Installed from External SD card, Aroma launcher ran and choose siyah kernel and Touchwiz S3 and choose custom install where I chose all applications.
3. Installed ok, phone rebooted and then ran the upgrade applications.
Upgrading symptoms.
a. Either it hang at the boot rom page. Force reboot and it run upgrade applications again
b. When it booted up again, i got an error android.phone not responding and i had to reboot since nothing will be displayed (black screen with notification). Tried fixing permissions in the recover mode didnt work.
c. a few times even when i chose Touchwiz launcher during installing, when it managed to boot up it gave me Apex launcher. When this happen it was very buggy (no input)
I then decided to try a fresh install
Steps Fresh install
1. Boot into recovery mode and factory reset , wipe cache and dalvik cache
2. Install rom and choose siyah, touchwiz s3 as default launcher then installed all software from custom installation and reboot to the wizard process
3. Once after wizard mode reboot and wipe cache and dalvik cache
Fresh install issues
a. It hangs at the end of wizard setup and cannot proceed once the setup is done. When the happens wipe cache and dalvik cache doesnt do anything to help. (meaning if the phone fails at setup wizard i have to repeat the install process. but before that i need to wipe the internal storage)
b. Once i wipe the internal storage, installation and going to the setup wizard is good. Touchwiz launcher also works perfectly. However i am faced with another issue. I am using Mybackuppro to back my data and apks. I did attempt to install superuser and make sure in extweats my phone was rooted before continuing..
What happen is that I can restore my sms/mms/contacts/ but if i reboot the sms icon will disappear and then be re-recreated again (funny symptom)
For mybackup pro app data + apks restore, i can restore only apps but not data. If i try that the phone will reboot. I wrote to the mybackuppro developer but they told me it had something to do with the ROM, not their software.
So at the moment i am not able to use the new rom due to the above problems and i am back on sniper wolf rom..i can only use the new rom if i dont want to port my apk data over, something which i am not willing to do n ow. Was wondering if anyone faced the same issues and managed to work through these problems and can offer some advice?
Thank you.
Hello,
i'm having the same issue. I did a fresh install following all the steps, but the rom freezes after i setup my google account. Then, it reboots and the launcher seems to don't work. I tried with touchwhizz as default, nova launcher and even apex launcher. I just can't get this rom working.
Thank you for this awesome rom anyway, sniper wolf is fantastic. But if anyone knows how to solve this please help me.
Sorry for my English.
Hello,
I have been running liquidsmooth rom on GB for a bit now and I started getting app crashes and random reboots. i went online and found AOCP was highly recommended for the i717. i downloaded this and added to my SD card and was following the instructions i found for installing it. the instructions on the site i was looking at seemed a little odd as it included the wipe of the system dir which no other rom had recommended doing.
i use TWRP as for my recovery and followed these instructions. i wiped cache, dalvik, and system, i even did the factory reset as normal. i was able to install the rom and get it to open up and what not BUT i do not have any gapps installed. i was able to use the web browser and download goo manager and install the gapps but when i open it to setup my acct it keeps crashing. i rebooted my phone into recovery again and wiped cash and restarted. now as soon as the phone boots and i try to go to my home i get the following errors: "Unforunately, setup wizard has stopped." and "Unfortunately, the process com.google.process.gapps has stopped."
I dont know what to do! the rom works fine until i try to install the gapps.
any suggestions would be greatly appreciated!
Google the 20130301 (March 1st) Gapps... Download the zip put it with your ROM zip.. Wipe Cache/Delvik/ then Factory Reset/ Them wipe the system.. Use your TWRP to flash the ROM 1st then The Gapps zip.. Wipe Cache/Delvik ( option on bottom left of screen ).. you may want to consider flashing a JB Modem as well if your AOCP is a Jellybean ROM then reboot...
You didn't mention the ROM you installed. ICS and JB use different gapps. Make sure to match gapps with ROM.
Sent from my SAMSUNG-SGH-I717 using xda premium
Sounds like the gapps file is possibly corrupted or it may be for a different device
Sent from my SAMSUNG-SGH-I717 using xda premium
Hi,
I was running BeanStalk-4.4.270 03/18/14 by zymphad. Im not sure what the kernel was.
I tried flashing the ROM by ronasimi in this thread.
The ROM that i picked was cm-11-20140817-UNOFFICIAL-geeb & the kernel was gbx-kernel-lights-CM11.0-CAF.zip. Apart from this i picked the Google Stock package of PA GApps from here.
For flashing i did the following :-
1. backed up all my apps using TB from BeanStalk.
2. loaded the ROM, the kernel & GApps zip files into a folder on my sdcard.
3. rebooted into recovery(TWRP 2.6.xx), backed up my original ROM and lined up all the three flashable zips and flashed them. (The flash was successful)
4. Then i rebooted into system. But after reaching the home screen, i was getting errors "Unfortunately, the process com.android.systemui has stopped" & "Unfortunately, the process com.android.phone has stopped". I remembered it might be because i forgot to wipe dalvik & cache.
5. I again rebooted into recovery, wiped dalvik & system cache and tried booting into system. It was still giving the same issues.
6. I tried restoring my old ROM's backup. Surprisingly even that wouldn't solve the issue.
7. So i again flashed the CM11 ROMs. But this time, the boot process is getting stuck at the boot animation.
My Qs are as follows:-
1. Did i miss anything or do something that is not recommended (or maybe even dangerous)?
2. What should be my next step in resolving this issue?
Any help appreciated.
gautam_k said:
Hi,
I was running BeanStalk-4.4.270 03/18/14 by zymphad. Im not sure what the kernel was.
I tried flashing the ROM by ronasimi in this thread.
The ROM that i picked was cm-11-20140817-UNOFFICIAL-geeb & the kernel was gbx-kernel-lights-CM11.0-CAF.zip. Apart from this i picked the Google Stock package of PA GApps from here.
For flashing i did the following :-
1. backed up all my apps using TB from BeanStalk.
2. loaded the ROM, the kernel & GApps zip files into a folder on my sdcard.
3. rebooted into recovery(TWRP 2.6.xx), backed up my original ROM and lined up all the three flashable zips and flashed them. (The flash was successful)
4. Then i rebooted into system. But after reaching the home screen, i was getting errors "Unfortunately, the process com.android.systemui has stopped" & "Unfortunately, the process com.android.phone has stopped". I remembered it might be because i forgot to wipe dalvik & cache.
5. I again rebooted into recovery, wiped dalvik & system cache and tried booting into system. It was still giving the same issues.
6. I tried restoring my old ROM's backup. Surprisingly even that wouldn't solve the issue.
7. So i again flashed the CM11 ROMs. But this time, the boot process is getting stuck at the boot animation.
My Qs are as follows:-
1. Did i miss anything or do something that is not recommended (or maybe even dangerous)?
2. What should be my next step in resolving this issue?
Any help appreciated.
Click to expand...
Click to collapse
Flash TWRP 2.7.1 or Philz's touch CWM
than do a clean install
Wipe data and Format system
Flash any ROM (here CM 11 ) and Gapps
Flash proper kernel ( for CM 11 old Gprij-X kernel or neighborhood kernel)
Wipe cache and delvick cache
reboot profit
For more info :
ShoaibAhmed said:
Flash TWRP 2.7.1 or Philz's touch CWM
than do a clean install
Wipe data and Format system
Flash any ROM (here CM 11 ) and Gapps
Flash proper kernel ( for CM 11 old Gprij-X kernel or neighborhood kernel)
Wipe cache and delvick cache
reboot profit
For more info :
Click to expand...
Click to collapse
I tried flashing using TWRP but the flash failed. then I saw the video and thought of giving philz touch cwm a try. it worked like a charm. Thanks a lot for the help. For kernel I flashed gprojx-kernel-lights-CM11.0-CAF-20140414.zip. Everything seems to be working now. Only thing is that I can't seem to turn off NFC. Every time I deselect the check box, go somewhere else and come back, the NFC check box is already checked.
Any tips on that? It's eating up my battery
gautam_k said:
I tried flashing using TWRP but the flash failed. then I saw the video and thought of giving philz touch cwm a try. it worked like a charm. Thanks a lot for the help. For kernel I flashed gprojx-kernel-lights-CM11.0-CAF-20140414.zip. Everything seems to be working now. Only thing is that I can't seem to turn off NFC. Every time I deselect the check box, go somewhere else and come back, the NFC check box is already checked.
Any tips on that? It's eating up my battery
Click to expand...
Click to collapse
Reboot once and then try to turn off NFC , it will work.
ShoaibAhmed said:
Reboot once and then try to turn off NFC , it will work.
Click to expand...
Click to collapse
Awesome! Thanks a lot man.
One last Q p)- I spent almost 30mins combing through settings but I couldn't find a 3G/2G switch. Is it hidden somewhere or it doesn't exist yet in CM11?
gautam_k said:
Awesome! Thanks a lot man.
One last Q p)- I spent almost 30mins combing through settings but I couldn't find a 3G/2G switch. Is it hidden somewhere or it doesn't exist yet in CM11?
Click to expand...
Click to collapse
Settings--->Mobile networks--->Prefered network type--> change it from "LTE" to 2G/3G
ShoaibAhmed said:
Settings--->Mobile networks--->Prefered network type--> change it from "LTE" to 2G/3G
Click to expand...
Click to collapse
i am actually looking for a shortcut for the same in notification draweer or quick settings pulldown...apologies for not making it clear before.
gautam_k said:
i am actually looking for a shortcut for the same in notification draweer or quick settings pulldown...apologies for not making it clear before.
Click to expand...
Click to collapse
Found the shortcut in Settings> Notification Drawer> Quick settings panel> Tiles & layout> Network mode
For some reason i was thinking that this will lead me to the GSM/WCDMA switch.
Hi;
So i recently installed CyanogenMod 13.0 on to my Samsung S4 GT-I9505 using the first download link on:
https://download.cyanogenmod.org/?device=jfltexx --> cm-13.0-20160102-NIGHTLY-jfltexx.zip
That all installed fine, but i wanted to get the Google apps installed aswell, which is where i am having some issues.
I have been trying to install the following package:
http://opengapps.org/?api=6.0&variant=nano
but have also tried to install quite a few others as well, and all have exactly the same issue. Basically after the apps have been installed and i boot the device up, i get various error messages like:
unfortunately, Setup Wizard has stopped
unfortunately, google play services has stopped
Any help on fixing this would be much appreciated, as nothing seems to download from the play store thats included in Cyanogen, they just say "your download will begin shortly" but never does.
Thanks in advance
I am a total noob, but I had exactly this problem. The issue appears to be that you have to flash gapps *before* rebooting after flashing CM. In my case since I had already flashed CM before I flashed gapps I had to put the gapps file on the phone (I did this by push with adb, you might find an easier way), re-flash CM, wipe cache/dalvik, flash gapps, wipe cache/dalvik, reboot. It worked.
The easiest guide I found was on androiding.how, called "how to install cm13 (cyanogenmod13)." (The forum won't let me post a link, just google it, it should come up).
Hope that helps. I'm on a galaxy s5 and used twrp recovery if that matters.
audacityandrouge said:
I am a total noob, but I had exactly this problem. The issue appears to be that you have to flash gapps *before* rebooting after flashing CM. In my case since I had already flashed CM before I flashed gapps I had to put the gapps file on the phone (I did this by push with adb, you might find an easier way), re-flash CM, wipe cache/dalvik, flash gapps, wipe cache/dalvik, reboot. It worked.
The easiest guide I found was on androiding.how, called "how to install cm13 (cyanogenmod13)." (The forum won't let me post a link, just google it, it should come up).
Hope that helps. I'm on a galaxy s5 and used twrp recovery if that matters.
Click to expand...
Click to collapse
Thanks for the reply, i gave that a try and it seems to be stuck on a loop now with "installing app # of 22" . it completes the installation and then reboots, after about 5 minutes on the Cyanogen boot screen, it goes back to installing apps again.
Hm, did you do a factory reset in your recovery before re-flashing CM and gapps? If not, that might be necessary.
audacityandrouge said:
Hm, did you do a factory reset in your recovery before re-flashing CM and gapps? If not, that might be necessary.
Click to expand...
Click to collapse
Yeah, i did. Tried it multiple times now
That's about the limit of my ability right there, hopefully someone with more experience than me can point you in the right direction. Good luck.
Boot to recovery (preferably TWRP)
Wipe cache / dalvik cache / data / system
Flash CM13 and the gapps you were trying first
Reboot
Profit!
Since you keep flashing different gapps on top of the system, this is probably causing some issues. Once you fully wipe and reflash everything, it should work.
es0tericcha0s said:
Boot to recovery (preferably TWRP)
Wipe cache / dalvik cache / data / system
Flash CM13 and the gapps you were trying first
Reboot
Profit!
Since you keep flashing different gapps on top of the system, this is probably causing some issues. Once you fully wipe and reflash everything, it should work.
Click to expand...
Click to collapse
Ive tried that multiple times using twrp (i always wipe everything before i flash CM13 and gapps), i still get the exact same issue. The second the phone boots, i get all these "unfortunately ******** has stopped".
Perhaps try installing 12.1 with gapps, get it all updated then upgrade to 13. I did the accidental upgrade to 13 but have had no issues whatsoever.