Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
Hi i was new to all this and installed dynamics v2.0 fully unlocked rom the other day and this is how i went about it
download this
RUU_Mozart_Orange_UK_1.24.061.35_Radio_5.50.09.18_22.24.50.09U
http://www8.zippyshare.com/v/48117282/file.html
this is a load your phone back to 1.24
to install it i did this
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial but maybe it will need to install some drivers cant remember 100%
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that then you will have your phone back to 1.24
next you can follow this post here and download the attachment at the bottom named DFT_XSPL_WP7FG1.rar this what u need for this step
http://forum.xda-developers.com/showthread.php?t=1195647
basically this is the install procedure u may need to install active sync (XP) or windows mobile device center (vista and 7) but i did not have to my phone automatically did this
DFT_RSPL_WP7FG1_LAUNCH allows you to load RSPL on the device:
1. Extract ALL files from RAR archive.
2. Run DFT_RSPL_WP7FG1_LAUNCH (with administrative rights to access USB)
3. Mindfully reads information text. Press “Next” button.
4. Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
5. Connect your device to PC via USB cable.
6. Now you may need to install proper USB drivers. They come with Active Sync / Windows Mobile Device Center.
7. Install drivers if required.
8. Make sure device show “USB” at the bottom instead of “Serial”.
9. Press “Next” button in the wizard. It should detect your phone.
10. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
11. After successful connection it should show device codename and allows to choose installed OSPL version.
12. You should look at the screen and select OSPL version in drop down list box. You need do this because it’s not possible to detect installed version via USB.
If your current SPL version doesn't present in the list, you can choose nearest version,
BUT ONLY IF IT HAS SAME FIRST NUMBER!!
Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.
13. Press “Next”. Wait until comes final page.
14. Read and close window
15. Look at the device – it must reboot to RSPL.
16. If you see RSPLX.Y.Z and “CotullaRSPL” on the screen – the task done! Otherwise, please report in this thread about your problems.
17. Put some feedback in this thread for community and developers.
Installing HSPL
DFT_HSPL_WP7FG1_INSTALL allows you to install HSPL on the device:
1. Launch RSPL on the device like described above.
2. Be sure that you close RSPL wizard window.
3. Run DFT_HSPL_WP7FG1_INSTALL.exe (with administrative rights to access USB)
4. Mindfully reads information text. Press “Next” button.
5. Proper drivers already must be installed in RSPL step.
6. Press “Next” button in the wizard. It should detect your phone.
7. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
8. After successful connection it should show device codename and allows to choose HSPL or OSPL version to install. OSPL means you install stock SPL back.
9. Check device codename, if something wrong turn off computer and run to the nearest forest. Grab some water with yourself.
10. Press “Next”. Wait until comes final page.
11. Device will reboot and start to boot OS.
12. Reset it and enter SPL mode again. Be sure there HSPLX.Y.Z and “CotullaHSPL” appear.
13. Put some feedback in this thread for community and developers.
Now u are ready
you can find what custom rom you want i used dynamics v2.0 which can be found here and its fully unlocked aswell so all i all im pleased with it
http://forum.xda-developers.com/showthread.php?t=1520352
download it and install the same way we installed the 1.24 rom in the begining of this post
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that and then you will have loaded your desired custom rom onto your phone
I hope this helps some of u out and happy modding
best regards
steve
1.24
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
geofferz said:
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
Click to expand...
Click to collapse
1.24 im refering to the SPL you can find your version by turning the phone off holding volume down and power button and u will see your SPL at the top,
im not sure about the unlocked sim/network im new to all this aswell maybe do a search on the forums and see if you can find the answer, but i dont know this 1 sorry :/
rom is good no issues had a cable issue yesterday that wouldnt let me charge my phone but thats down to my dodgy cable
you dont have to install this rom you can use any custom rom you like or might find out there
anyways hope this helps
Launch RSPL
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
geofferz said:
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
Click to expand...
Click to collapse
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Oh also do not extract the 1.24 from the .rar file run everything from there
This is why ur getting that error I think
geofferz said:
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
Click to expand...
Click to collapse
you dont need to select a option just load ROMUpdateUtility.exe
ive just downlaoded and reinstalled the rom myself to try see what u mean and i dont get this option
when you go to bootloader screen on your phone and it says usb open the rom file and click ROMUpdateUtility.exe
now dont open active sync or mobile tools as it says on the program information
just click the tick boxes and continue through the process
maybe try download the rom again found this
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
but like i sed i have downloaded the file myself and it is working for me without any problems
beany2009 said:
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Click to expand...
Click to collapse
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
geofferz said:
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
Click to expand...
Click to collapse
lol np mate ill try help as best i can
right i understand your bit now about the dynamics rom u need to select regular on this part
custom i think would be if u want to edit it or some **** but i have no idea so u use regular mate because this is the actual rom file made but remember u must downgrade and load rspl and hspl onto your phone before doing this step
right my firmware is 2250.21.51301.401 but i dont know if this changes on installation of the downgrade and adding the custom rom like i sed im a complete noob with this myself but all went smoothly for me thats why i made the tutorial
and no mate my phone took about 5-10 mins to install the 1.24 orange rom
have u tried a hard reset first and then see if it helps with the installation
ill search around for your firmware and see if there has been issues
edit..........................................
did a search on the forums and your firmware comes up with nothing :/ did a google and only shows this thread did you type the numbers correctly?
also you mean that the rom update works sometimes and not others?
if it works once it should install it mate np's
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
beany2009 said:
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
Click to expand...
Click to collapse
again thanks for your help
ok here goes red: PD 67100 ss-BC (4k)
SPL-4.6.2250.0(129193) mng
what you think?
i think my SPL was on that before so i dont know why u are having issues mate :/
maybe wait and see if a developer can read this and give us some info on why its not working for you :/
Thanx For The Help And the Tutorial It Was very Helpfull
Now my phone Is running dynamic 2.0
hey can u tell me what other custom roms are available that i can install on my phone and if there are any different methods of installing them
no problem mate glad it helped
erm the only other custom rom i have seen on mozart is deepdishing v7.0 you can find this in the development thread inside mozart topics
and for me mate im not sure and have not seen another way of installing another custom rom but im new to all this myself
anyway glad this helpped
regards
my computer wont pick up htc 7 mozart in bootloader
can anyone help me its doing my head in .
when you connect your phone to pc in bootloader its not showing as usb on the bottom of bootloader screen?
just serial?
just to confirm. this wont work on Asian handsets.
beany2009 said:
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
steve
Click to expand...
Click to collapse
Thx for the easy to follow guide.
It worked on a telstra brand mozart using windows 8.
Sent from my GT-N7105 using Tapatalk 2
Related
i search for it but i can't find it
i want to flash my rom but if i go the splash screen en i run on my pc the rom update it goes to de gray window and i see 0% and nothing happend
can anybody help?
thanks tom
reading wiki is really hazardous to our health.
make sure ur device hv HardSPL installed.
Put ur device in bootloader mode, flash the rom.nbh file using raphael ruuwrapper.
Look at this:
http://htc.back2basic.shacknet.nu:8084/
There you can find a Dutch manual about flashing your TP.
thanks for your help
but it's also not working
the hardspl works but untill the gray screen is still on 0% and never go to 1%
HELP :S
tom1687 said:
thanks for your help
but it's also not working
the hardspl works but untill the gray screen is still on 0% and never go to 1%
HELP :S
Click to expand...
Click to collapse
Dear friend,
Use the fastest, simplest and safest method:
1. Flash Hard SPL
2. Rename the nbh file of the desired ROM after RAPHIMG.nbh
3. Copy it to the root of your SD Card
4. Enter bootloader mode [press vol. down and soft reset]
5. Follow on-screen instructions
Good luck and cheers.
hello Kevlar-Source
i have found the problem i can't flash with windows vista it dont work now have i done what you say on the storage cant and flash ik whit windows xp and it's works
thanks
PROBLEM SOLVED
did u follow the steps exactly? also make sure to remove sim card before flashing hardspl.
Works with Vista, no prob!
What i did wrong, was that the folder was not empty with just the loader and rom... Took me a while
I hope you take the manual by the letter, you should be able to upload the rom. You must also use a USB-cable to flash the phone! Don't forget to have the "Mobilitycentrum" open.
Daneels said:
You must also use a USB-cable to flash the phone!
Click to expand...
Click to collapse
Just to quote George Cooney: "What else?"
Guys I was updating my Old Gene to vanilamanila
but suddenly error 270 occured and my device reset itself and didnt opened anymore.
how can I fix it???
try to upgrade your SPL
hey its by KRAZY ABOUT TECHNOLOGY {senior member XDA} you can find the whole thread
The Step By Step Guide
The Step By Step Guide
CAUTION: DO NOT UPDATE ROM OF A PHONE THAT IS SIM LOCKED. THE RESULTS ARE UNKNOWN BUT MOST OF THE TIMES IT PREVENTS YOU FROM USING THE PHONE ANY FURTHUR!!
If you like to backup your existing rom first, follow this guide by Ankit360 to do it : http://forum.xda-developers.com/show...8&postcount=20
Step 1: Download the Tools
-------------------------------
Download the tools zip file from here:
http://www.4shared.com/file/81084740...ing_Tools.html
Its a self extracting file, just start it and give a path and it will unzip all the files in your chosen folder. Inside the extracted folder you will find these things:
1. SPL Updater : Inside it there are 2 folders, Olipro and Orefkov. These contain the two SPL patchers that we need to use.
2. ROM Update Utility : This contains the ROM update utility we will need to flash a ROM. Unzip it into a folder.
3. USBDriver4ActiveSyncVista : This contains a special driver for Windows Mobile Device Center in Vista that you need to use to successfully update your ROM. Unzip it in a folder too.
4. Download a ROM appropriate for your device: Which one is appropriate, you'll only know after updating your SPL. So do this step after that. But in any case, here is a link to a good ROM, created by me, which is available for both new and old gene:
Sumit's Pro Users ROM (WM 6.1, for new and old gene)
http://forum.xda-developers.com/showthread.php?t=467796
Step 2: Preparing your phone
--------------------------------
1. Copy the file gene_hspl.exe from the SPL Updater\Olipro folder that you got in step 1 to the phone memory.
2. First, on your phone, Go to Start > Settings > Connections > USB to PC. Here, uncheck the checkbox : enable advance nerwork functionality. Click OK. Disconnect and Reconnect the USB cable to your pc.
Step 3: Prepare your Computer
--------------------------------
XP Users
----------
There is not much you need to do. Just open task manager and kill the Active Sync executable from the processes tab. Its named as wcescomm.exe.
Vista Users
-------------
You need to take these steps :
1. Go to desktop, right click Computer, and select Manage. Go to Device Manager. Now under the section Mobile Devices, Double Click : Smartphone USB Sync.
2. On the Drivers tab, click "Update Driver..." button. On next screen click : "Browse my computer for driver software".
3. Click : "Let me pick from a list of device drivers on my computers". Click "Have Disk.." on next screen. Click "Browse..." and go to the folder extracted in step 1. There, go to USBDriverforActiveSyncVista folder. Here select the file "wceusbsh.inf" and click OK.
4. Click Next and finish the wizard.
Step 4: Use the Olipro method first.
-----------------------------------------
Open File manager on your phone. Go to the location on phone memory where you saved gene_hspl.exe. Tap on it to run it. Your phone will restart after a short pause.
Now there are two chances :
a) If its done alright, you'll see SPL 1.10.Olip on your boot screen and your phone will boot just fine. And it confirms that you have an old gene. You do not need to do Step5. Proceed to Step 6.
b) If it doesn't boots, and only green and red keys blink, Don't worry. Your phone is bricked but you'll get it back using orefkov's method in a minute. Proceed to next step. And this confirms that you have a new gene.
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
Step 7 : Set your PC and Phone back to normal
------------------------------------------------
This step is only needed in case you are using Vista.
The driver we updated in Vista will not work for normal active sync operation. So you'll need to set it back to the original version. There are two ways to do that. Either, uninstall and reinstall the Windows Mobile Device Center Or Follow the same procedure gicen in Step 3 but instead on clicking the "Have Disk button", choose the driver from the list already given.
The driver that you need to install can be identified by have a newer version given in front of its name. Also, the newer driver's name includes "Microsoft Corporation" while the older one has only "Microsoft".
You can Put back your SD card now.
On your phone, again go to the Start > Settings > Connections > USB and check the checkbox there and click OK.
That's it! You are Done.
__________________
HTC P3400i (New GENE)
@rockyyyrulz
the link you provided is for trinity not for gene.cant do such a thing.
@Beco35
try to tell us exactly what the device show and try this
remove the battery and press the power button for a while
then put back the battery and press and hold down the camera key and in the same time press the power (without holding down) if you got a screen with three colors then you will be having a very good chance to recover your gene.
try it and tell what happened.
error 270
Upgrade error number 270 means that the bootloader is not correct for the rom you are trying to flash
sorry
my apology
Beco35 said:
Guys I was updating my Old Gene to vanilamanila
but suddenly error 270 occured and my device reset itself and didnt opened anymore.
how can I fix it???
Click to expand...
Click to collapse
Before starting a thread everyone has to go through all the existing threads on the related topic.Many threads carrying the same problem that you are facing.
Read all these and as rockkyy suggested read gene upgrading step by step guide by sumit.Gud Luck
get it here
hi
look at the bottom of my signature and clik on it it will take u to sumits stiky
save it on ur comp it also has all req tools do it word for word and success will be urs
good luck
rakesh_4utoo said:
Before starting a thread everyone has to go through all the existing threads on the related topic.Many threads carrying the same problem that you are facing.
Read all these and as rockkyy suggested read gene upgrading step by step guide by sumit.Gud Luck
Click to expand...
Click to collapse
@rockyyy : For heavens sake, do not post full tut in threads like these man, its a waste of space and bandwidth and its annoying to scroll though it everytime. A link to the original post would have done that easily. In case you aren't aware, every post has a number in its top right corner like this one has #8. This number is also a permanent link or permalink to that post and it can be used to refer to it. Just right click on the number and copy the link address.
Thx for ur helps rocky rakesh mido haree
but the problem is my Gene cannot connect to the pc. screen is black and by the time I connect with USB activesync not strarting and my pc not see my device... Gene cannot open, Usb is not working and the link u have designated in first reply doesnt work (4shared....)
wat to do - take to service
hi
im not a techi and it looks like u have to take it to the service and chek with them
good luck
Beco35 said:
Thx for ur helps rocky rakesh mido haree
but the problem is my Gene cannot connect to the pc. screen is black and by the time I connect with USB activesync not strarting and my pc not see my device... Gene cannot open, Usb is not working and the link u have designated in first reply doesnt work (4shared....)
Click to expand...
Click to collapse
ok thx for ur great efforts
try this o got the same problem
hi
i got the same problem today ie phone not turning on
thats wat happened to me wen i flashed a rom i got it up and running this is wat i did try it
1. take battery out and hold camera button and powebutton for some time
2.put battery back
3. press power and camera if u get tricolor flash rom( this did not work for me)
2.Use stylus rest keep pressing camera button while doing this
i got try color i flashed new ROM i did this in the last 1hr
i hope this will help u and also save ur Phone
if u cant get wat i say clik on the link i think it is explained better
goodluck
http://forum.xda-developers.com/showpost.php?p=3637172&postcount=8
Beco35 said:
Guys I was updating my Old Gene to vanilamanila
but suddenly error 270 occured and my device reset itself and didnt opened anymore.
how can I fix it???
Click to expand...
Click to collapse
u r vonderfull sweethrt )) now my gene connected to pc ) I finally saw the three color screen... I ll follow the steps which u posted in 1st reply... many many thx...
I hope I d update my gene..
On The Three colo0r screen
ONBL 1.07.0000
SPL 1.07.Oref
is written..
what s the meaning ?
@Beco
you are good to go now
go and flash any old rom and you will get it back running
good luck
mido0109850352 said:
@Beco
you are good to go now
go and flash any old rom and you will get it back running
good luck
Click to expand...
Click to collapse
I downloaded the original ROM from HTC and flashed but after the installation GENE Did not started. returned to brick. I ll try again and inform u
Don't flash the official ROM. It Contains IPL and SPL. Hence your device is bricked again.
which one you downloaded
tell us as soon as possible cause you might have bricked it
Yupppiiiiiiii.....
Yess Yess Yesss... I did it ))
Rescued my gene )))
many many thx to alll supporters especially to Haree and Mido
th u very very much for ur helps and patience...
I downloaded this one Ramersonw...
ftp://213.194.123.227/Cep Bilgisayari - Pocket PC/HTC/Gene 3400/
first it bricked but after 2nd flash everythng good )
good so everything is good now nice
try the new wm6.5 for old gene not new gene it is very good
give it a shot and dont worry it wont brick yours.
goodluck
ITS A HTC HD2 NOT THE ORIGINAL
Ok I am a really big noob and need some help. I Flashed My rom using Miri_HD2_WM65_21893_Sense25_V6.0.rar, I extracted in and it completed 100% and loaded up perfectly to home screen. I didnt have my sim card in or Sd card so I took battery out and put my sim card and sd card back in. When I turned it back on it was stuck on the HTC screen. Just the Green HTC writing and white screen and thats it. I have read some forums that have had the same problem but i just dont get it. they say get into bootloader ( which i can do) and then flash with radio or something... I am uncertain how to do this. When I downloaded one of them Customruu or whatever it is and open it it says I have to connect through active sync which i cant do because I cant get my device to turn On... I really need some help but it needs to be explain to me like explaining to a handicap person.
thanks
Put into bootloader, not necessary to connect to Activesync as you can't in bootloader mode. Flash the radio the same way as you flashed the rom. put the radio.nbh file in a folder, rename it to RUU_Signed.nbh and copy a CustomRUU.exe in and flash.
You'll find radios and steps here.
jaza20032000 said:
Ok I am a really big noob and need some help. I Flashed My rom using Miri_HD2_WM65_21893_Sense25_V6.0.rar, I extracted in and it completed 100% and loaded up perfectly to home screen. I didnt have my sim card in or Sd card so I took battery out and put my sim card and sd card back in. When I turned it back on it was stuck on the HTC screen. Just the Green HTC writing and white screen and thats it. I have read some forums that have had the same problem but i just dont get it. they say get into bootloader ( which i can do) and then flash with radio or something... I am uncertain how to do this. When I downloaded one of them Customruu or whatever it is and open it it says I have to connect through active sync which i cant do because I cant get my device to turn On... I really need some help but it needs to be explain to me like explaining to a handicap person.
thanks
Click to expand...
Click to collapse
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
where do I get the Customruu.exe from? What do you mean flash the radio same as the rom? how can i do that if i cant get connect to active sync? So does that mean I have to download Miri_HD2_WM65_21893_Sense25_V6.0.rar again? which radio file do I choose? I am so confused. Dont get annoyed its just i dont understand all this...
do NOT do it via SD card - flash the radio using activesync as mentioned in first reply. SD card is dodgy as hell and the quickest way to brick your phone for good
You can get CustomRRU from any ROM file - use the one from Miri's ROM
might've been worth reading the n00b flashing thread first as well as well as the first thread of Miri's ROM as all the info is on there...
how come you can't use activesync? what version of Windows you using?
in future i suggest you read the relevent threads and make sure you can flash a stock ROM before jumping into cooked ROMs...don't wanna brick an expensive phone do you?!?!
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
I can't use the SD card because I dont have the adapter thing to be able to hook it up to my comp only way i could access it was through my phone in hard drive mode. So basically i cant put any files on it without using the phone... Any other suggestions?
futher info from Miri's ROM thread...
"You MUST use radio 2.07.50.27 or 2.08.50.08"
read this thread...
http://forum.xda-developers.com/showthread.php?t=609477
all will become clear - or it should do!!
EddyOS said:
do NOT do it via SD card - flash the radio using activesync as mentioned in first reply. SD card is dodgy as hell and the quickest way to brick your phone for good
You can get CustomRRU from any ROM file - use the one from Miri's ROM
might've been worth reading the n00b flashing thread first as well as well as the first thread of Miri's ROM as all the info is on there...
how come you can't use activesync? what version of Windows you using?
in future i suggest you read the relevent threads and make sure you can flash a stock ROM before jumping into cooked ROMs...don't wanna brick an expensive phone do you?!?!
Click to expand...
Click to collapse
If you read my post I cannot get into the home screen... My Phone is stuck on the HTC boot up screen therefore making it impossible to use activesync... I did read all the Noob and Miri **** and it worked. I got to the new rom, but when i took the battery out and put sim card and sd card back in it is just stuck on the green htc screen and wont go past it...?????????
jaza20032000 said:
I can't use the SD card because I dont have the adapter thing to be able to hook it up to my comp only way i could access it was through my phone in hard drive mode. So basically i cant put any files on it without using the phone... Any other suggestions?
Click to expand...
Click to collapse
i would say buy one only cost about £5 to £10 uk pound
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: http://forum.xda-developers.com/showthread.php?t=575524) with the radio file from this link:
http://megaupload.com/?d=HT7ZMDGH
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
EddyOS said:
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: ) with the radio file from this link:
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
Click to expand...
Click to collapse
Where do I get jus the CustomRRU.exe..?? For miri?
Edit: Just read post again you included link in last quote, yes i know i am retard
I put a link for it in brackets (found here: ) - use your eyes!! lol
if you're not prepared to read what people put then don't ask for help
EddyOS said:
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: http://forum.xda-developers.com/showthread.php?t=575524) with the radio file from this link:
http://megaupload.com/?d=HT7ZMDGH
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
Click to expand...
Click to collapse
I am using a HTC LEO (HD2) with EnergyROM installed in it. Now I was tryin to flash updated version (11th march update), But I am having trouble with Activesync which somehows is from last few weeks. It connects & syncs the device too once USB is plugged in, But disconnects when I try to flash a rom using customRUU..It gets disconnected on the bootloader screen & activesync status turns to Disconnected from Connected..I pull out my battery & restart the device again. This is highly irritating & I wish if there's some other program instead of Activesync that could be used to flash a rom.
I tried doing it with bootloader screen, Turning the device off, then turning it on while pressing down the volume button, It sure goes into bootloader screen, but shows Serial at the bottom & not USB..So any ideas for what could be the alternative for people who face the same problem with activesync, Instead of wasting time to rectify this error, Its better to find some other alternative. My PC is running Windows XP 32 bit, I re-installed my windows when i had trouble almost a month back & activesync worked fine then, But just can't afford to do it every other week or so
????
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
when i do this hd2 says NOT ALLOW What should i do??
sbugra said:
when i do this hd2 says NOT ALLOW What should i do??
Click to expand...
Click to collapse
Flash via pc
ClydeB1 said:
Flash via pc
Click to expand...
Click to collapse
done it. thnx
vicky_crispy said:
I am using a HTC LEO (HD2) with EnergyROM installed in it. Now I was tryin to flash updated version (11th march update), But I am having trouble with Activesync which somehows is from last few weeks. It connects & syncs the device too once USB is plugged in, But disconnects when I try to flash a rom using customRUU..It gets disconnected on the bootloader screen & activesync status turns to Disconnected from Connected..I pull out my battery & restart the device again. This is highly irritating & I wish if there's some other program instead of Activesync that could be used to flash a rom.
I tried doing it with bootloader screen, Turning the device off, then turning it on while pressing down the volume button, It sure goes into bootloader screen, but shows Serial at the bottom & not USB..So any ideas for what could be the alternative for people who face the same problem with activesync, Instead of wasting time to rectify this error, Its better to find some other alternative. My PC is running Windows XP 32 bit, I re-installed my windows when i had trouble almost a month back & activesync worked fine then, But just can't afford to do it every other week or so
Click to expand...
Click to collapse
It's not possible to connect to Activesync while being in the bootloader mode (The hd2 says "USB" on Windows without activesync too), so it has nothing to do with Active sync. Try another USB-Cable or use the sdcard to flash (see amma2005's Post, but as far as I know, there is no need to format the card again).
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
Great advice mate.
Been a rom junkie for weeks, bouncing around several releases to find the one.
turned towards Dutty, flashed and got a wihte screen for my trouble. Followed your advice and now running CDLC V2 "dutty" without a hiccup.
eng.mohammad said:
Dear Friend;
i faced the same problem and thanks my ALLAHH, i found that the connector copper pin that connect the battery with the phone is not in its right direction so i used my hand to redirect it to can connect with the battery
Click to expand...
Click to collapse
Hi. Can you help with this? or anyone?
leo70 said:
Hi. New here. Done this magldr 1.12 and leo70 rom but my phone playing up badly after a lot of droid and 6 and other flashes. I can't install hardly any rom any more without it - ie: stock, wm6, android, wp7 rebooting constantly for no reason etc.
Done mtty and have bad blocks - about 16 and 16 reversed. done task 28 and task 28 55aa, and task 29 as read in other threads. tried everything with different radios, different nand droid. multiple wp7-hd2 installs. but still reboots.
Any thoughts? If go back to stock+spl1.66 and send back under warranty anyone know/think if they will fix it and/or replace it? they still have old sealed replacement hd2 stock or boards much? do they do diagnostics and look at bad blocks properly on warranty return? Even on stock-rom and stock-spl still does this reboot although not as much. Worried that stock-rom wm6 will "work" too well and they won't check blocks. What about task2a? etc? Any way to install wp7/magldr and partition right so no bad blocks counted in?
Thanks very much.
Will pay for fix that works - $.
Click to expand...
Click to collapse
I am stuck on DFT boot screen after hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage.
and yes, was Windows Phone 7 and activated with marketplace & xbox/live.
leo70 said:
Hi. Can you help with this? or anyone?
I am stuck on DFT boot screen after hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage.
and yes, was Windows Phone 7 and activated with marketplace & xbox/live.
Click to expand...
Click to collapse
Did you check the battery pins ? Sometimes they do get bent out of alignment and simply pushing them back into place gently does the trick.
Im having some issues with my x10i that i put Nordic 2.1 on a few weeks ago.
Some apps fail to open every now and then, and the stock android alarm doesnt work (the app seems fine, but when the alarm goes off there is no noise, yes ive tried volume etc, yes ive tried downloading a 3rd party alarm)
So id like to put a fresh 2.1 rom on, ive tried these:
http://forum.xda-developers.com/showthread.php?t=825675
http://forum.xda-developers.com/showthread.php?t=827065
But i cant get them to work, the .bat files of the flasher fail at the connection stage (2nd step after selecting windows vr)
Im having a lot of problems,, main one is that i cant install the driver for the x10 in flash mode, windows cant find the driver.
If anyone could kindly tell me exactly what i have to do, starting from connecting the x10 to a virgin win xp (no drivers installed for the x10), id be happy to donate $20USD into your paypal account
Ok let me see if I can help you a title here....
1. Root your device using this http://forum.xda-developers.com/attachment.php?attachmentid=453551&d=1291188836 its really simple and fast...
2. Once you've root your device use this application http://www.mediafire.com/?ewf9e41ybw2eazz
to install the Xrecovery menu on your phone... It's very simple as well....
3. Download this file http://hotfile.com/dl/87564842/7e80127/SE_update-shipped-full.zip.html
and save it to your SD Card into any folder you want, I recommend you to do it in a new one with any name you want, that will make easier the next step...
4. Reboot your phone and right after the white letters with Sony Ericsson logo appear press the back key a few times , if the Xrecovery menu has been installed correctly you will see a weird image of and Android with troll face lol... and a bunch of options like reboot, install update zip etc....
5. Choose Install Custom Zip and then go to the folder you created with the downloaded zip file... from step 3... Then select it and click in yes... Wait for a few minutes and when the phone tells you done click on reboot and wait for the firmware to load...
6. Enjoy the SE 2.1 firmware with JIT enabled.
7. Read your inbox...
Jimmy
Sent from my AOSP on Xperia (Guatemala)
Siddy1200 said:
If anyone could kindly tell me exactly what i have to do, starting from connecting the x10 to a virgin win xp (no drivers installed for the x10)
Click to expand...
Click to collapse
Put XP in safemode, run seus, put phone in flashmode when prompted so it installs the drivers, try the flashtool again, while in safemode on XP.
Or if you'd rather go for something simpler.. try rooting (if you haven't already) then follow this - http://forum.xda-developers.com/showthread.php?t=828163 to flash to global generic.
i cant even get the phone to tunr on atm, but if i get it to work ill send $20 ur way jimbo, thanks everyone
jimbo, actually your links are broken so i cant follow your guide cause u just say "use this application" - but link is down
ok, i found a new link for that one, but i cant install it cause when i connect my phone to the pc, it just starts charging, it wont mount the sd??
"If anyone could kindly tell me exactly what i have to do, starting from connecting the x10 to a virgin win xp..."
ok i put xrecovery on the sd card through a pc, installed the app and ran the app, clicked Install Xrevovery, error
already have root access, xreovery was granted superuser, but doesnt work
tried the new root app just in case, it just switched off my phone... none of this works
does anyone live in Sydney and can do it for me????
Have you installed BusyBox too?
Hello, I am a newbie Android user and I have been exploring the greatness of the OS for few days now.
Just now I tried to update my firmware to 2.3.5 and followed instruction from a non-xda developer site and little did I know, it messed up my phone big time.
While I was loading all the files (CSC, tar, modem, etc), and I should've known better when the site told me to check the "re partition" box, but I was stupid enough to go along with it.
So Odin got stuck at re-writing the modem or something like that and I had to pull out the battery from the phone.
Now the phone turns on only in recovery mode and none of the recovery choices work, if I choose one it just shows a little green android with white bordered triangle with an orange exclamation mark in the middle.
I can still access the download mode by using conventional button pressing method, but my phone is NO LONGER RECOGNIZED through the USB so I cannot flash the old stock firmware...
Is there a fix for this? If anyone can help me resolve this issue I am willing to compensate very well in return...
Thank you so much for reading my convoluted troubled story, and I really hope to find some resolution in your wisdom.
If u can't reflash your farmware
Than their is only one option left
give it to the Samsung service center they will repair your phone
Sent from my GT-S5570 using xda premium
I'd be down to do so but it will be hard as I have 4 custom binary flash counter... What can I do as of now?
i dont know if this helps you out buddy but maybe if you read in this thread you might find people that had the same trouble as you..just try and search the thread first and if nothing comes up try and read the first page maybe there you might get an idea on how to unbrick the phone
http://forum.xda-developers.com/showthread.php?t=1075278
Thank you.. But I unfortunately did not follow the instructions that is written there I used an external source which told me to check "re partition" which completely messed up the phone, I think. Thank you for your input, though.
sfoksn said:
Thank you.. But I unfortunately did not follow the instructions that is written there I used an external source which told me to check "re partition" which completely messed up the phone, I think. Thank you for your input, though.
Click to expand...
Click to collapse
i dont want to advice you wrongly but you say you can get into download mode right? if it was my phone i would try and flash again but this time using the proper way to do it....but its down to you my friend i dont want to say do it and it gets worse..
EDIT: apologies i just saw that your usb is not recognised...do you have kies on the background when you flash with odin?
Check this unbricker
android-roms.googlecode.com/files/DREAIMG-RC29.zip
Download DREAIMG-RC29.zip and unzip the file.
Reformat the SD card to FAT32 and copy the DREAIMG.nbh onto it.
Safely eject the SD card.
Put the SD card into your device.
Step 3: Wipe The Phone
Hold home and press the power button.
When you see the image of an ! mark, open your keyboard and press Alt + L if you cannot see any command options.
Do a factory reset by pressing Alt + W or just using the trackball.
When the reset is done, go ahead and hold the camera button and select the reboot system now option with your trackball.
Step 4: Flashing The Phone
Once the grey screen pops up (or the white screen if your phone was rooted with JesusFreke) it will ask you to hit a button to start installing the image…press that button. DO NOT DO ANYTHING TO STOP THIS PROCCESS. It will take about 8-12 minutes.
When the image has completed the installation (it will say completed), go ahead and press the green, red, and menu buttons at the same time. The phone will reboot.
And your done! Your phone is now unbricked!.
If this helps u buy me a HTC sensation.
debsattam said:
Check this unbricker
android-roms.googlecode.com/files/DREAIMG-RC29.zip
Download DREAIMG-RC29.zip and unzip the file.
Reformat the SD card to FAT32 and copy the DREAIMG.nbh onto it.
Safely eject the SD card.
Put the SD card into your device.
Step 3: Wipe The Phone
Hold home and press the power button.
When you see the image of an ! mark, open your keyboard and press Alt + L if you cannot see any command options.
Do a factory reset by pressing Alt + W or just using the trackball.
When the reset is done, go ahead and hold the camera button and select the reboot system now option with your trackball.
Step 4: Flashing The Phone
Once the grey screen pops up (or the white screen if your phone was rooted with JesusFreke) it will ask you to hit a button to start installing the image…press that button. DO NOT DO ANYTHING TO STOP THIS PROCCESS. It will take about 8-12 minutes.
When the image has completed the installation (it will say completed), go ahead and press the green, red, and menu buttons at the same time. The phone will reboot.
And your done! Your phone is now unbricked!.
If this helps u buy me a HTC sensation.
Click to expand...
Click to collapse
Thanks for such detailed instruction! Would this method work if my phone is no longer recognized by the computer though? Please clarify what you mean by "open your keyboard" and the subsequent steps...
Thank you, once again!
sfoksn said:
Thanks for such detailed instruction! Would this method work if my phone is no longer recognized by the computer though? Please clarify what you mean by "open your keyboard" and the subsequent steps...
Thank you, once again!
Click to expand...
Click to collapse
Yeah it althrough works . Try it its helps he to unbrick ma t mobile oncemay be It works on ur phone to
Sent from my GT-S5570 using xda premium
Ah I see. Could you please help me understand what you mean by "open keyboard?" I just don't see how I could open keyboard on my SGS2 when it isn't recognized by my computer... If you could clarify what you mean by that it will be really appreciated!
So from your information provided, you have a stock recovery and your phone is semi-bricked. You can still boot and your computer won't recognize your phone.
Do you have a jig? What firmware did you flash? You could use a jig to reset the flash counter on the phone and return it for warranty saying that Kies messed up while upgrading firmware. If you've flashed the KI3 with the new bootloader then the jig won't be able to clear the flash counter.
EDIT: Maybe an experienced senior member might come and look at this thread and provide some other solution. Do wait!
EDIT2: Try reinstalling Kies and the drivers. Don't give up just yet!
sfoksn said:
Ah I see. Could you please help me understand what you mean by "open keyboard?" I just don't see how I could open keyboard on my SGS2 when it isn't recognized by my computer... If you could clarify what you mean by that it will be really appreciated!
Click to expand...
Click to collapse
I don't think that the guide he posted is particularly for galaxy s2 because he also mentioned a trackball...
but if you can go the settings he mentioned you might find something and lead you.
And if you decide to bring the phone to samsung you might want to have a read at Intratechs Official firmware
thread in (Original Android Development)there you can find a bootloader that you can flash so you can use the jig to reset the counter
edit: wow I also failed to read that your computer can't recognise your phone
anymore....
Have you tried to delete the samsung drivers when you go to
your hardware settings?? and let windows find it's drivers again?
Not sure if this will help. I read somewhere someone else with their PC not really recognizing the phone. Someone else advised to unplug the phone and remove the battery then connect to PC insert battery and put it into download mode.
I could be wrong with the method. Its just from my memory.
Also this may make no difference but maybe removing the sim and SD card. Someone will probably call me stupid for suggesting that though.
I wouldn't try that unbrick method mate. That looks like it is an unroot for an old phone..possible the G1 (AKA HTC Dream).
Thanks for all the help... I have been trying to uninstall the driver and reinstall it but no luck. If I could just get the phone to be recognized I think I will be fine, but I just don't know what to do
Thank you for all the suggestions, please keep them coming!
EDIT: this is the guide I used that messed up my phone.. http://androidflip.com/install-andr...-samsung-galaxy-s2-gt-i9100-installing-guide/
EDIT: Tried to reinstall KIES, no luck. It's like there's nothing on the other side of the USB cord... Not even a sound when I plug the phone in...
If it had been via XDA the instructions are do not do what they are saying .
In Odin Select Re-Partition , Auto Reboot and F.Reset Time
In Odin select these files
For PIT select u1_02_20110310_emmc_EXT4.pit
BIG BIG NO to the above .
As usual some stuff ripped from XDA and some from elsewhere .
My suggestion would be one buy USB jig it hopefully will clear the rom counter and enter download mode .
two in recovery mode go to mounts and storage and format cache data dalvik system and sd card .
Clean phone with nothing on it .Flash stock firmware .
http://forum.xda-developers.com/showthread.php?t=1075278
If PC does not now recognise phone either try another PC or return phone to service centre and say it failed on a Kies upgrade .
jje
Go through the following steps on your PC or laptop:
1. Go to Start
2. Panel
3. Programs and Features
4. Windows features on or off (then a list compiled, this can take several seconds).
5. Then you see a check stand Microsoft. NET Framework 3.0 or 3.5 (if not, tick)
6. Open the sub folders with the + and then be there for the 3 sub folders a checkmark (if not checked, any configuration takes several minutes)
- Windows Communication Foundation HTTP Activation
- Windows Communication Foundation Non-HTTP Activation
- XPS Viewer
7. Then click OK
8. Now start up your computer.
9. Now you choose to uninstall through Programs and Features
10. Also remove the Samsung USB Driver.
11. Then download the latest version of Kies on the Samsung site and install it.
12. Now launch the program Select Samsung and go to the Tools tab.
13. Then click on drivers.
14. Once this is complete close the Galaxy S2 with the USB cable to your computer.
15. If all is well you now have access to your phone via the USB connection.
If there are any questions, you can leave a response below.
I am not sure if this will help but you might want to have a try. I got this
from a Dutch website. I google translated it for you and hoping you wont
have trouble reading it. This is one of the guides posted when some of us
here couldn't connect our phone with the usb cable.
droidluck said:
Go through the following steps on your PC or laptop:
1. Go to Start
2. Panel
3. Programs and Features
4. Windows features on or off (then a list compiled, this can take several seconds).
5. Then you see a check stand Microsoft. NET Framework 3.0 or 3.5 (if not, tick)
6. Open the sub folders with the + and then be there for the 3 sub folders a checkmark (if not checked, any configuration takes several minutes)
- Windows Communication Foundation HTTP Activation
- Windows Communication Foundation Non-HTTP Activation
- XPS Viewer
7. Then click OK
8. Now start up your computer.
9. Now you choose to uninstall through Programs and Features
10. Also remove the Samsung USB Driver.
11. Then download the latest version of Kies on the Samsung site and install it.
12. Now launch the program Select Samsung and go to the Tools tab.
13. Then click on drivers.
14. Once this is complete close the Galaxy S2 with the USB cable to your computer.
15. If all is well you now have access to your phone via the USB connection.
If there are any questions, you can leave a response below.
I am not sure if this will help but you might want to have a try. I got this
from a Dutch website. I google translated it for you and hoping you wont
have trouble reading it. This is one of the guides posted when some of us
here couldn't connect our phone with the usb cable.
Click to expand...
Click to collapse
Thanks, I tried to do this but unfortunately the problem persists... What do you think the root of the problem is? I just dont' get it why it won't be recognized anymore.. I feel like I could easily get it to work if I could just get it to become recognized to flash stock firmware....
EDIT: JJE, I would turn it into the service place but I have custom rom count of 4 And I don't have any USB jigs to work with either.... I am still within the 15 days of the phone purchase day, would they be willing to swap my phone?
BUMP, any input would be appreciated...