Hello guys
Tools Needed to separate digitizer
i got the digitizer from ebay,
hot air gun
exacto knife
i used IR thermometer to measure
double sided tape
first i thought removing the digitizer completely, and i experimented in old broken evo 3D digitizer to find out at what temp the glue between the glass and the plastic digitizer starts to lose(85-90degree Celsius)
after i found out that removing the glass pieces from the digitizer layer would be much easier,
my buddy helped me with the heat gun.
keep it moving don't stop at a spot it will damage the lcd,maintain temp between 85celcius(185F)to90celcius(194F)
using the knife remove the glass piece, remove one piece at a time.don't dig deeper when glass pieces are completely removed start heating at the top slowly peal of plastic digitizer layer from the lcd,
During this process maintain the temp at 85deg cel because dna lcd did't have the side metal support if the temp is low or you hurried means the top layer of the lcd will rip off .
after that i checked the lcd it worked no bleed or blackink
I cleaned the old glue and applied the double sided tape. the seller did't gave me pre cut tape so i have cut 2mm for sides and copied the old glue patter at the top and bottem . align the lcd use tape on the backside don't forget to peal of the soft key light diffuser from old one and transfer it to new one
i attached couple of photo taken doing this in a rar file
a pair of hands will be helpful and luck from Jesus .
Be careful with the knife i cut my fingers twice and glass pieces will fly around so wear glasses.
This is great news, however, I already destroyed my LCD in the process of finding that temperature. I was wondering if you could explain the pattern for the double sided tape. Does it not completely surround the opening around the LCD? Should there be a gap for the digitizer ribbon?
mohit321 said:
This is great news, however, I already destroyed my LCD in the process of finding that temperature. I was wondering if you could explain the pattern for the double sided tape. Does it not completely surround the opening around the LCD? Should there be a gap for the digitizer ribbon?
Click to expand...
Click to collapse
you need to make a slot for ribbon cable and holes for front camera and sensor.
Where did you get your double sided tape or could you recommend a source? Thanks
wu_li said:
Where did you get your double sided tape or could you recommend a source? Thanks
Click to expand...
Click to collapse
you can use 3m tape. i used nippon tape.
hello
everyone
i have been reparing cellphones for over a year and i made few videos with a lot details about how to separate LCD from the broken gorilla glass. Also i made a video explaning all the theory behind it and after that all the practices so you can see how it is made. I hope it help you all guys.
Theory of how to fix gorilla glass at any samsung galaxy
https://www.youtube.com/watch?v=qOAauYYNUuI
how to repair galaxy s4 screen glass replacement (gorilla glass)
https://www.youtube.com/watch?v=J458v0LNkkI
how to remove gorilla glass from LCD on galaxy S3
https://www.youtube.com/watch?v=MnuoCm_erYI
how to change display from a galaxy s4 (complete frame LCD
https://www.youtube.com/watch?v=85pOvI6OV_Q
enjoy!
shajubinglish said:
Hello guys
Tools Needed to separate digitizer
i got the digitizer from ebay,
hot air gun
exacto knife
i used IR thermometer to measure
double sided tape
first i thought removing the digitizer completely, and i experimented in old broken evo 3D digitizer to find out at what temp the glue between the glass and the plastic digitizer starts to lose(85-90degree Celsius)
after i found out that removing the glass pieces from the digitizer layer would be much easier,
my buddy helped me with the heat gun.
keep it moving don't stop at a spot it will damage the lcd,maintain temp between 85celcius(185F)to90celcius(194F)
using the knife remove the glass piece, remove one piece at a time.don't dig deeper when glass pieces are completely removed start heating at the top slowly peal of plastic digitizer layer from the lcd,
During this process maintain the temp at 85deg cel because dna lcd did't have the side metal support if the temp is low or you hurried means the top layer of the lcd will rip off .
after that i checked the lcd it worked no bleed or blackink
I cleaned the old glue and applied the double sided tape. the seller did't gave me pre cut tape so i have cut 2mm for sides and copied the old glue patter at the top and bottem . align the lcd use tape on the backside don't forget to peal of the soft key light diffuser from old one and transfer it to new one
i attached couple of photo taken doing this in a rar file
a pair of hands will be helpful and luck from Jesus .
Be careful with the knife i cut my fingers twice and glass pieces will fly around so wear glasses.
Click to expand...
Click to collapse
lcd
please help me, I have htc droid dna and want to replace LCD display with touch screen digitizer, does fit model X920e lcd with screen my droid dna? is X920e butterfly and droid dna lcd screen same?
Related
Howdy all,
What size double sided tape should I use to stick my Asus TF201 digitizer and LCD back together? I have 3 options, a 1mm, 2mm and 3mm double sided tape. Not sure whats on it now, but if anyone has an idea I'd really appreciate it.
Thanks
Nightpath said:
Howdy all,
What size double sided tape should I use to stick my Asus TF201 digitizer and LCD back together? I have 3 options, a 1mm, 2mm and 3mm double sided tape. Not sure whats on it now, but if anyone has an idea I'd really appreciate it.
Thanks
Click to expand...
Click to collapse
I recommend not using any foam tape at all to stick the digitizer to the LCD. I thought there'd be light leaks if I didn't. There were no light leaks. I used double-sided scotch tape to stick the digizer to the front bezel. It worked very well.
If you *do* use foam tape to stick the LCD to the digitizer, you'll go ape-**** crazy if you notice any fingerprints or particles on the inside of the digizer. Without sticking the two together, you can easily separate the two if you need to.
So double sided scotch tape eh? Whats the difference, just easier to take apart if you have to?
Might be an idea, seems to be more of it around here and waaayyy cheaper
Would this be it (put in b0p 1n0 if it asks for a postal code)? : http://www.staples.ca/ENG/Catalog/c...191,4,6&name=CA_SK_SCOTCH+-+Double-Sided+Tape
here's another, says it's removeable tape so I don't think that's a great idea : http://www.staples.ca/ENG/Catalog/cat_sku.asp?CatIds=3,3191,4,6&webid=33734&affixedcode=WW
Here's mounting tape, would this work too you think? http://www.staples.ca/ENG/Catalog/cat_skuset.asp?CatIds=3,3191,4,6&name=CA_SK_3M+-+Mounting+Tape
And here's a tape of MC Hammer : http://www.youtube.com/watch?v=otCpCn0l4Wo
LOL on the MC Hammer!
On the mounting tape, keep in mind that the Prime's display has two types of mounting tape. The digitizer glass is affixed to the plastic bezel with very thin (and very sticky) double-sided celophane type adhesive. Then, the LCD is affixed with black foam tape (and screws). i used the Scotch tape to stick my digitizer to the bezel. This had the advantage of being very easy to trim with an exacto. I chose not to use any foam tape at all with the LCD and just rely on the screws to hold it in place. I was needlessly worried about light bleed. It did not. It was fine.
By not using foam tape, I had the HUGE advantage of being able to later remove a tiny speck of debris that got sandwiched between the LCD and digitizer. It was very small, but drove me nuts. If I had used foam tape to mount the LCD, the risk of breaking the damned thing again would have been too great to try removing the speck. It'd still be there.
I highly recommend not using any foam tape. At least try without first. You can always add it later if your heart is set on it. I've read other threads where folks ended up breaking the digitizer or LCD when having a foam-tape malfunction (stuck to the wrong spot, wasn't lined up right, etc.).
I don't use cheap tape or scotch tape (3m) as generally it's not sticky enough for most jobs like this.
I highly recommend mammoth tape for this job. https://www.google.co.uk/search?q=m...AW81oG4Bg&sqi=2&ved=0CFoQrQQ&biw=1067&bih=693 don't get the one with the cloth membrane (labeled as Heavy duty double sided tape) as its too thick and very hard to cut, the one you need is labeled "multi purpose double sided tape".
I get it from a builders merchants but you can get it online. I have tried many brands and alternatives but mammoth is the best stuff I have found.
Ultimately folks can do whatever they want and feel comfortable with. I would council any close friends to just go with the double-sided Scotch tape to stick the digitizer glass to the bezel. It's plenty sticky enough and there's enough (around 1m total perimeter) that you get a good stick. BONUS: It's good and cheap.
With as fragile as the digitizer glass is, you really don't want to screw around with ridiculously sticky adhesives. On the likely chance (unless you're a pro) that you don't set the glass in the bezel just right, highly sticky adhesive is going to make repositioning much harder and you may very well break the new glass trying to reposition.
I highly recommend not using any adhesive at all to hold the LCD to the digitizer for the reasons I've already mentioned. You'll really wish you hadn't.
Jgrimoldy said:
Ultimately folks can do whatever they want and feel comfortable with. I would council any close friends to just go with the double-sided Scotch tape to stick the digitizer glass to the bezel. It's plenty sticky enough and there's enough (around 1m total perimeter) that you get a good stick. BONUS: It's good and cheap.
With as fragile as the digitizer glass is, you really don't want to screw around with ridiculously sticky adhesives. On the likely chance (unless you're a pro) that you don't set the glass in the bezel just right, highly sticky adhesive is going to make repositioning much harder and you may very well break the new glass trying to reposition.
I highly recommend not using any adhesive at all to hold the LCD to the digitizer for the reasons I've already mentioned. You'll really wish you hadn't.
Click to expand...
Click to collapse
That's what I was thinking. My LCD was slightly cracked on the edge, but not noticeable. With the 2 sided Scotch tape ($5 here) if it breaks again I can replace it without totally busting the LCD. And if it's sitting in a decent case the screen is going to be reinforced anyway.
Nightpath said:
That's what I was thinking. My LCD was slightly cracked on the edge, but not noticeable. With the 2 sided Scotch tape ($5 here) if it breaks again I can replace it without totally busting the LCD. And if it's sitting in a decent case the screen is going to be reinforced anyway.
Click to expand...
Click to collapse
I'm not sure going without the foam is the right thing in all instances. I'm working on a Casio G'Zone Commando, replacing the digitizer, and noticed that the digitizer will only work accurately if it is elevated slightly more than if it just sits on the frame where the foam tape was at. I can't tell if the digitizer is just wonky or if the slight elevation caused by the foam tape is needed with this phone.
I know this has been discussed before but I would like clarification on what I need to replace on my TF201. I am attaching pictures. I actually sat on my tablet and it damaged the LCD. The glass is fine but the display is not. Can someone tell me what I can do? Do I need to replace the whole screen? It powers on okay. Thank you!
thispdxgirl said:
I know this has been discussed before but I would like clarification on what I need to replace on my TF201. I am attaching pictures. I actually sat on my tablet and it damaged the LCD. The glass is fine but the display is not. Can someone tell me what I can do? Do I need to replace the whole screen? It powers on okay. Thank you!
Click to expand...
Click to collapse
If the digitizer glass on the front is okay, you'll need to replace the LCD panel. The digitizer glass and the LCD are separate pieces. When you open your Prime, you'll see that the entire "display assembly" is a sort of sandwich. The digitizer glass is attached with dobule-sided tape to a thin piece of black plastic. The LCD is attached to the other side of the plastic with thin double-sided foam tape. Additionally, there are small brackets that hold the LCD to the plastic.
You're going to need to separate the LCD from the plastic with an exacto then clean away the remaining sticky foam crap. Order a replacement LCD, then reinstall.
Me, I reinstalled mine without using any sticky foam tape. I rely on the brackets. I'm glad I did it that way because I noticed a speck of dust after I re-assembled. It drove me nuts. If I'd used tape, I'd have never been able to get the piece of dust out.
A few notes: the LCD is VERY delicate and VERY fragile. Yours is already broken, so there's no real risk with the old one. The digitizer, comparatively, isn't quite as delicate. Still, BE CAREFUL when removing the LCD from the bracket. You DO run the risk of breaking your digitzer glass.
Also, leave the protective cover on the replacement LCD until the last possible moment of re-assembly. Use rubber gloves. You'll be unhappy if you leave a fingerprint on the replacement. Cleaning off fingerprints with alcohol or Windex risks breaking the new LCD. Did I mention that it's delicate?
Good luck
My friend gave me a note 2 and it has a cracked screen. I was wondering if i should replace the screen+digitizer or just the digi. The lcd still works and so does the digitizer but a cracked screen just annoys me.
lolwutwin said:
My friend gave me a note 2 and it has a cracked screen. I was wondering if i should replace the screen+digitizer or just the digi. The lcd still works and so does the digitizer but a cracked screen just annoys me.
Click to expand...
Click to collapse
yes the glass alone is I'm thinking around 30 us dollars on the web the glass is glued together to the amoled lcd touch panel and can be removed with the following tools .....hair dryer highest heat setting, plastic tweezers, I actually took the whole phone apart to avoid heat damage to the internal components. apply heat to the whole screen from the outside only. caution very hot so wear gloves now slowly and I repeat very gently with tons of patience start prying off piece by piece then clean and losen the glue with alcohol then I used a stain remover I cant think now but will get back to you on that good luck
I do not know if this has been mentioned or brought up before, but I just wanted to let the G2 crowd know that if they want to go the cheaper route and replace just the digitizer on their G2, it is possible with patience! You will be separating the glass from the LCD with a little bit of heat and a lot of caution, so as not to bust that beautiful LCD that these things are packin'. As you all may already know, the front glass is the digitizer so it'll all be replaced and your touch will work again, without busting the bank! This should only be considered if you're a very handy person with some superfine motor skills.
All you really need is a steady heat source of around 200F. I use a griddle, similar to this
http://www.walmart.com/ip/16451315?...56276670&wl4=&wl5=pla&wl6=34449323470&veh=sem
Most people have one of these laying around in a cabinet.
Get on eBay and find the digitizer for the phone and some LOCA UV Adhesive. 10ML is way more than enough.
Take the phone apart, then lay the LCD/Digitizer face down on that griddle and let it sit for about 10 minutes. Use a razor blade to VERY CAREFULLY and slowly peel the glass back. You should see the glass separating from the LCD. Continue this and take your time until all of the glass is removed. Then clean the LCD. It takes some work, this glue is extremely sticky and the only thing I've found to completely remove it is Clorox Surface wipes. They're the kind that come presoaked with some kind of cleaner. Even those take a little elbow grease to completely remove the glue from the LCD surface. It should be shiny. A couple specs wont matter, the LOCA has proven to be great at hiding imperfections. Next you will remove the LCD from the frame of the phone. There will be some connectors following through the bottom half of the phone to the PCB that has the charging port on it. Once the LCD is removed, add a line of LOCA glue to the LCD about as wide as a cigarette. Lay your new glass down on that glue, being careful not to trap too many bubbles. If you have a couple, no problem. You can leave them if it doesn't bother you, or you can push them to the edges. Next, align the LCD with the handy little lines that are printed on the back of the glass. Get something to hold it together, clothespins or hair clamps will do fine. After clamping, once again ensure the glass is aligned properly with the LCD. Then all you have to do is take it outside, let it cure in the sun for about 5 minutes, clean the extra glue up and reassemble the phone!!! I've got one waiting for a glass to come in so as soon as I get that I'll try to post some pics. Enjoy the savings, and the adventure!
add video replace touch screen.
VirtueToVice said:
I do not know if this has been mentioned or brought up before, but I just wanted to let the G2 crowd know that if they want to go the cheaper route and replace just the digitizer on their G2, it is possible with patience! You will be separating the glass from the LCD with a little bit of heat and a lot of caution, so as not to bust that beautiful LCD that these things are packin'. As you all may already know, the front glass is the digitizer so it'll all be replaced and your touch will work again, without busting the bank! This should only be considered if you're a very handy person with some superfine motor skills.
All you really need is a steady heat source of around 200F. I use a griddle, similar to this
http://www.walmart.com/ip/16451315?...56276670&wl4=&wl5=pla&wl6=34449323470&veh=sem
Most people have one of these laying around in a cabinet.
Get on eBay and find the digitizer for the phone and some LOCA UV Adhesive. 10ML is way more than enough.
Take the phone apart, then lay the LCD/Digitizer face down on that griddle and let it sit for about 10 minutes. Use a razor blade to VERY CAREFULLY and slowly peel the glass back. You should see the glass separating from the LCD. Continue this and take your time until all of the glass is removed. Then clean the LCD. It takes some work, this glue is extremely sticky and the only thing I've found to completely remove it is Clorox Surface wipes. They're the kind that come presoaked with some kind of cleaner. Even those take a little elbow grease to completely remove the glue from the LCD surface. It should be shiny. A couple specs wont matter, the LOCA has proven to be great at hiding imperfections. Next you will remove the LCD from the frame of the phone. There will be some connectors following through the bottom half of the phone to the PCB that has the charging port on it. Once the LCD is removed, add a line of LOCA glue to the LCD about as wide as a cigarette. Lay your new glass down on that glue, being careful not to trap too many bubbles. If you have a couple, no problem. You can leave them if it doesn't bother you, or you can push them to the edges. Next, align the LCD with the handy little lines that are printed on the back of the glass. Get something to hold it together, clothespins or hair clamps will do fine. After clamping, once again ensure the glass is aligned properly with the LCD. Then all you have to do is take it outside, let it cure in the sun for about 5 minutes, clean the extra glue up and reassemble the phone!!! I've got one waiting for a glass to come in so as soon as I get that I'll try to post some pics. Enjoy the savings, and the adventure!
Click to expand...
Click to collapse
Please post updates....with pics etc.
Have a perfectly good LCD at home now with damaged digitizer and frame I'd rather use vs playing around with these crappy Ebay replacement parts I've gotten in the past month
It is not easy to replace but it is very easy to damage LCD, it's not so expensive to buy new screen with digitizer and frames (90-100$) so i prefer to buy full lcd and dont try to replace digitizer.
If u guys can see at the side of the screen just between the middle body and the lcd screen there's a adhesive lining, when i was cleaning my phone i accidentally took out a bit portion of it, is it okay to leave it or should i get lcd adhesive and just paste the part with it? And is there's another layer of adhesive other than the outside part that i meantion earlier that keep the phone waterproof?