Related
Hello all.
This guide will help you if you have:
A phone that will not turn on unless you plug it in and even then only an LG sign shows up followed by either blank/ rapidly flashing red light.
to my knowledge, what happened to put the phone in this state is the battery died while you were flashing a rom or something as such and the phone got confused on if it should be in charge mode or not.
being that the phone has a sealed battery, it is not as easy to pull out the battery as it is on other phones.
Fortunately for us, it is not difficult at all to unplug the battery!
REQ: torx screw driver that will fit but NOT STRIP the screws at the bottom of the phone.
Small phillips screw driver.
**I suggest charging the phone for a good 10 minutes before starting this. just to make sure it has a charge.
Step 1: unscrew the two screws at the bottom of the phone CAREFULLY!
Step 2: with your nails carefully pry up the back cover (inspect the phone carefully and identify the back cover from the rest of the phone.) off starting from the bottom of the phone.
Step 3: peel back the blue tape on the connector and remove the two screws.
Step 4: carefully pry up the connector from the top.
Step 5: plug back in and try powering on. By this point you should know if it worked and you can start putting the phone back together.
This guide is not the best (My first) but if you have any questions send me a message.
Good luck with your phones!
One of the first official LGOG teardown! Looks easier than expected..
@exemplarmusik sent from his LG - E970 ya dig?!
Awesome job, man. should come in handy for me at some point I am sure. I am curious though, those internals look identical to the Nexus 4's (as I guess we should expect) and I know the battery is glued down with the Nexus 4, so is that the case with our LGOG as well?
Yeah. The battery is glued in. I dont see an issue replacing it though. maybe a heat gun to losen up the glue and you should be good.
And yeah, it is very easy to open up.
This would have helped me last week. Oh well, got a replacement device and a free LG headset for my trouble.
Sent from my LG-E970 using Tapatalk 2
Fission_Chipz said:
Awesome job, man. should come in handy for me at some point I am sure. I am curious though, those internals look identical to the Nexus 4's (as I guess we should expect) and I know the battery is glued down with the Nexus 4, so is that the case with our LGOG as well?
Click to expand...
Click to collapse
Yeah the name in system info is even mako just like n4
the best phone ever
drwario said:
Yeah the name in system info is even mako just like n4
the best phone ever
Click to expand...
Click to collapse
I think it would only say that if unlocked, then you have N4 bootloaders.
I had this fast flashing "brick"-like issue, but after I let my phone cool, I just held power and vol-up and my phone went straight to the boot loader.
Sent from my LG-E970 using Tapatalk 2
Damn, I didn't think it'd be that easy to take it apart. I wonder if it'd be possible to stick a Qi wireless charger pad in there, like the Nexus 4.
First of all, thanks for the guide. :good:
Here is what caused this to happen on my phone:
(black screen, flashing red light)
With phone off and charger plugged in you should be able to press power for a couple of seconds and it will show the charging progress. When you unplug the charger and press power you should see nothing unless you hold it long enough to power up the phone. Problem was that no matter how long you waited after unplugging the charger you could press power and see the progress ::what::
That causes the battery to drain, completely if left alone for a couple of days resulting in, you guessed it, black screen and flashing red light. After leaving it plugged in for 4-5 hours it regained a full charge and was fine.
This did not occur when phone was on while charging. Needless to say, I exchanged the phone. Hope this helps.
Don't assume you have any other pictures
I was considering trying to steal the signal amplifier and the filter from this and put in n4 ... and chance you got any shots of those in the optimus g ?
I still cant get mine to turn on, I unhooked the battery, still nothing. I hold the power it goes to the lg screen then nothing. I can hold power and volume up and nothing happens. Does anybody have a idea, I want my phone back.
Thanks
HELP!
My phone somehow will not turn on or charge! I have tried multiple chargers and outlets, and my phone will not charge or get the red light signaling that it is... There is no damage to the phone other than a small crack done a couple months prior. This happened very suddenly, the phone just ran out of batteries then stopped charging... is it possible to find the same battery as this and replace it?? My phone company said LG would not accept it because of the small crack on the front screen corner. Any help would be very greatly appreciated, really dont have the money to buy a phone off contract...
amazingbonz said:
My phone somehow will not turn on or charge! I have tried multiple chargers and outlets, and my phone will not charge or get the red light signaling that it is... There is no damage to the phone other than a small crack done a couple months prior. This happened very suddenly, the phone just ran out of batteries then stopped charging... is it possible to find the same battery as this and replace it?? My phone company said LG would not accept it because of the small crack on the front screen corner. Any help would be very greatly appreciated, really dont have the money to buy a phone off contract...
Click to expand...
Click to collapse
My phone is same yours. you plug and unplug somes times untill red light flash then push power button. goodluck
Wow looks like there are connectors on the back to go to the inside of the back cover... I wonder if this is compatiable with the orbe!... if not it should be easy to use old Palm Touchstone parts to make it charge wirelessly.
I have the sprint version I am hoping it has the same connectors... You guys see the two prongs on the back cover adn the metal places they attach to??
Akop87 said:
Wow looks like there are connectors on the back to go to the inside of the back cover... I wonder if this is compatiable with the orbe!... if not it should be easy to use old Palm Touchstone parts to make it charge wirelessly.
I have the sprint version I am hoping it has the same connectors... You guys see the two prongs on the back cover adn the metal places they attach to??
Click to expand...
Click to collapse
Those prongs are for connecting to the antenna in the back cover, not a wireless charger.
Sent from my Nexus 7
I could use some help guys, if this thread isn't too old. I've searched high and low to the answer here and nothing is working. I've tried download mode, fastboot, recovery, reset, holding power down, plugging it in and unplugging it. I've pulled the plate off of the battery, tried LGNPST, drivers, etc. No go on anything.
The phone is still dead, and will not turn on. The best I've gotten is a solid red light after holding the power button for 15-20 seconds. Then after about 3-5 seconds it resumes flashing (alternating between the red light and the key buttons). If I continue holding the power button down it will repeat this, showing solid red and then reverting to flashing.
I can not get the screen to display anything, not even the charging animation, and none of my computers will even recognize the device. I've been messing with it all day and I'm stuck. If anyone can help me, at all, please do. I hate going to Sprint. Anything but that, please.
thistimearound said:
I could use some help guys, if this thread isn't too old. I've searched high and low to the answer here and nothing is working. I've tried download mode, fastboot, recovery, reset, holding power down, plugging it in and unplugging it. I've pulled the plate off of the battery, tried LGNPST, drivers, etc. No go on anything.
The phone is still dead, and will not turn on. The best I've gotten is a solid red light after holding the power button for 15-20 seconds. Then after about 3-5 seconds it resumes flashing (alternating between the red light and the key buttons). If I continue holding the power button down it will repeat this, showing solid red and then reverting to flashing.
I can not get the screen to display anything, not even the charging animation, and none of my computers will even recognize the device. I've been messing with it all day and I'm stuck. If anyone can help me, at all, please do. I hate going to Sprint. Anything but that, please.
Click to expand...
Click to collapse
me too.
I was doing the LGNPST and it was stuck at 67% for 15 min so i unplugged and the phone did nothing so I turned it off from recovery and nothing. no power only the power flashes red for a few seconds after pressing.
I am out of town now but if I can get it to turn back on I will send it back since I just received it today.
Unfortunately, my phone is now completely unresponsive. I have had it plugged in to the original wall charger for over two hours and still no power. If i hold down the power button for about 15 seconds while plugged in the red light will blink once every second until i let go. However, if I unplug it and do the same the light will not come on. I'm about to disassemble my brick and see if the battery pull will help any.
Any success stories in detail would be appreciated. Plan B is to send it off to Mobiletechvideos.
Edit: Moving on to plan B....thanks.
Sent from my LGL35G using xda app-developers app
TangoXray said:
Unfortunately, my phone is now completely unresponsive. I have had it plugged in to the original wall charger for over two hours and still no power. If i hold down the power button for about 15 seconds while plugged in the red light will blink once every second until i let go. However, if I unplug it and do the same the light will not come on. I'm about to disassemble my brick and see if the battery pull will help any.
Any success stories in detail would be appreciated. Plan B is to send it off to Mobiletechvideos.
Sent from my LGL35G using xda app-developers app
Click to expand...
Click to collapse
I did this trick a couple weeks ago when my phone stopped responding. Could only get flashing light while plugged in, and no response when not plugged in. Eventually while plugged in I could get to the bootloader, but could not get to recovery. This fix worked for me, though it may not work for you. You will need a T5 torx (star) screwdriver. Good luck.
Last night i fell asleep and my phone died all the way, and now when i plug it in all i get is a lg logo then it goes away and then a dark lit up screen. ive let it charge for awhile now and i still get nothing, i cant get into cwm either.. the phone is unlocked and rooted and im running the base rom. Any help would be greatly appreciated.
Happened to me... leave it on the charger at least 3 hours and check it. The battery completely drains when you unplug the charger if you charged with the phone off. gl
Edit: If it still won't work, turn phone on and plug in charger.
Sent from my LG-E970 using xda premium
Pony Express said:
Happened to me... leave it on the charger at least 3 hours and check it. The battery completely drains when you unplug the charger if you charged with the phone off. gl
Edit: If it still won't work, turn phone on and plug in charger.
Sent from my LG-E970 using xda premium
Click to expand...
Click to collapse
This happened to me too. I completely drained the battery and it kept going into a loop (black screen, LG logo, battery screen). I left it plugged in and off and let it boot up.
FYI
This has happened to several people. I have confirmed through testing, even exchanging my phone 2 days ago that this is an issue created when unlocking the bootloader. Rooting does not cause it. Once the bootloader is unlocked, you can not get around this by re-locking the bootloader.
The workaround is simple. Either leave your phone on while it is charging or if you charge with phone off, unplug your charger and hit the power button- you will still see the charge animation running- this is what causes the battery to drain. All you have to do is power up the phone at least to boot then it is ok to turn off. You can confirm it worked by touching the power button again and not see the charge animation. Hope this helps.
Wow thanks so much for the reply and help! I've got it working now and I guess I'll just avoid it by not letting it die lol
Sent from my LG-E970 using xda app-developers app
well...
If you let it die all the way, its not a big deal. Plug it in, hold down the volume down button and the power button for 15 seconds, then it will work fine.
Threads like this makes this forum so great. Another potential problem to be avoided when using the phone.
Sent from my Nexus 7 using xda premium
I could use some help guys, if this thread isn't too old. I've searched high and low to the answer here and nothing is working. I've tried download mode, fastboot, recovery, reset, holding power down, plugging it in and unplugging it. I've pulled the plate off of the battery, tried LGNPST, drivers, etc. No go on anything.
The phone is still dead, and will not turn on. The best I've gotten is a solid red light after holding the power button for 15-20 seconds. Then after about 3-5 seconds it resumes flashing (alternating between the red light and the key buttons). If I continue holding the power button down it will repeat this, showing solid red and then reverting to flashing.
I can not get the screen to display anything, not even the charging animation, and none of my computers will even recognize the device. I've been messing with it all day and I'm stuck. If anyone can help me, at all, please do. I hate going to Sprint. Anything but that, please.
thistimearound said:
I could use some help guys, if this thread isn't too old. I've searched high and low to the answer here and nothing is working. I've tried download mode, fastboot, recovery, reset, holding power down, plugging it in and unplugging it. I've pulled the plate off of the battery, tried LGNPST, drivers, etc. No go on anything.
The phone is still dead, and will not turn on. The best I've gotten is a solid red light after holding the power button for 15-20 seconds. Then after about 3-5 seconds it resumes flashing (alternating between the red light and the key buttons). If I continue holding the power button down it will repeat this, showing solid red and then reverting to flashing.
I can not get the screen to display anything, not even the charging animation, and none of my computers will even recognize the device. I've been messing with it all day and I'm stuck. If anyone can help me, at all, please do. I hate going to Sprint. Anything but that, please.
Click to expand...
Click to collapse
Dude i had the same isse like your did, so i search everywhere and endup here. I'd try many think like you said, when holding volume+ and power there nothing heapen but volume down and power, or just hold the power buton there red light of front led is flashed, and ... is realy dead.
I can't go to any sevice central, coz my friend bring this telus P973 for me from another contry, and im living at the mountian lol. So im about to take it to nake and try to reset by reputing the batery. Devil beside me, i have 2 extra LG Lu6200 but 1 got broken the touch system, the other been death after i take a shower, Optimus G is using small sim and i'hv cuted it, there no other phone i can use that sim for tomorow, my girlfriend sending me some monney tomorow, and i have to meet my new boss and taking a new job that's make me traveling alot, and i don't have a laptop.
Don't know what to say when looking at the black cold silent phone i used to like most....
Some body, please help!
I have an s-off rooted droid dna and i went to flash a new rom today(i have flashed a few before) and it failed twice so i pressed restart in TWRP and the phone shut off and nothing else....
i tried plugging it in to a power source, computer and even wireless charger but nothing.
i have also tried to hard restart it every way possible including pulling the battery quick and trying again.
was hoping someone on here might know something I am missing.
thanks.
Syntax531 said:
I have an s-off rooted droid dna and i went to flash a new rom today(i have flashed a few before) and it failed twice so i pressed restart in TWRP and the phone shut off and nothing else....
i tried plugging it in to a power source, computer and even wireless charger but nothing.
i have also tried to hard restart it every way possible including pulling the battery quick and trying again.
was hoping someone on here might know something I am missing.
thanks.
Click to expand...
Click to collapse
How did you just "pull the battery quick" on your DNA?
From my S-Off BadSeed DNA
trickster2369 said:
How did you just "pull the battery quick" on your DNA?
From my S-Off BadSeed DNA
Click to expand...
Click to collapse
By using a pry tool taking off the back and disconnecting the terminal on the lower right side.
I know this might sound like w/e but have you tried just holding the power button down for a long time?
Syntax531 said:
I have an s-off rooted droid dna and i went to flash a new rom today(i have flashed a few before) and it failed twice so i pressed restart in TWRP and the phone shut off and nothing else....
i tried plugging it in to a power source, computer and even wireless charger but nothing.
i have also tried to hard restart it every way possible including pulling the battery quick and trying again.
was hoping someone on here might know something I am missing.
thanks.
Click to expand...
Click to collapse
Was the battery very low when you were doing this?
I had something similar (but different) happen the other night. I left the phone on a wireless charger and when I got up in the morning, the phone was completely dead. It's possible that I missed the charger and that the phone simply depleted its battery, there is no know I can tell.
I tried several different USB cables, wall chargers, wireless chargers, computers, and nothing would make it happy. Either nothing changed at all when I attached a power source or else the LED would blink on and off but it never gave me a solid charging light. I tried various charging techniques for 10 hours before I called Verizon for a replacement phone.
Later that night, I put it on a different brand of wireless charger and again it did nothing and finally put it back on my google charger at which point it started charging. It ended up charging just fine after that.
Although, it still wouldn't charge on some combination of cables, USB ports, etc. that used to work and that work with other devices.
I suspect that the charging circuitry is flaking out on the phone and somehow the different wireless charger made it reset some internal state or some other voodoo magic happened.
There isn't any great advice here other than to keep trying different power sources and see what is happening with the LED.
crpalmer said:
Was the battery very low when you were doing this?
I had something similar (but different) happen the other night. I left the phone on a wireless charger and when I got up in the morning, the phone was completely dead. It's possible that I missed the charger and that the phone simply depleted its battery, there is no know I can tell.
I tried several different USB cables, wall chargers, wireless chargers, computers, and nothing would make it happy. Either nothing changed at all when I attached a power source or else the LED would blink on and off but it never gave me a solid charging light. I tried various charging techniques for 10 hours before I called Verizon for a replacement phone.
Later that night, I put it on a different brand of wireless charger and again it did nothing and finally put it back on my google charger at which point it started charging. It ended up charging just fine after that.
Although, it still wouldn't charge on some combination of cables, USB ports, etc. that used to work and that work with other devices.
I suspect that the charging circuitry is flaking out on the phone and somehow the different wireless charger made it reset some internal state or some other voodoo magic happened.
There isn't any great advice here other than to keep trying different power sources and see what is happening with the LED.
Click to expand...
Click to collapse
I have tried 4 different charger(Samsung, htc, Googles, and a wireless changer) and i have done the holding power and vlume down.
Syntax531 said:
I have tried 4 different charger(Samsung, htc, Googles, and a wireless changer) and i have done the holding power and vlume down.
Click to expand...
Click to collapse
How long did you let it charge? I'd charge it overnight and try in the morning. If you got the phone from Verizon on contract, go and say the phone just died while charging and won't turn on now. I did that three times when I had a Lucid and I got 3 new ones free...
zinkscott said:
How long did you let it charge? I'd charge it overnight and try in the morning. If you got the phone from Verizon on contract, go and say the phone just died while charging and won't turn on now. I did that three times when I had a Lucid and I got 3 new ones free...
Click to expand...
Click to collapse
thanks for the reply and i did charge it last night from 10pm to 12 today and nothing. as for the verizon thing, i bought it off ebay with a cracked screen so i cant do that haha
how long was it disconnected ( i would leave it for about 5 minutes), and once you had it back on did you leave it on a ac charger(and not a qi one) for at least 12 hours? EDIT: just saw post above it didn't load for some reason lol. Dont hold volume down at first hold just power for for about 30-40 seconds the soft keys will flash then keep holding the device till you see white screen(if you get that) then let go and hold just volume down.
reaverclan said:
how long was it disconnected ( i would leave it for about 5 minutes), and once you had it back on did you leave it on a ac charger(and not a qi one) for at least 12 hours? EDIT: just saw post above it didn't load for some reason lol. Dont hold volume down at first hold just power for for about 30-40 seconds the soft keys will flash then keep holding the device till you see white screen(if you get that) then let go and hold just volume down.
Click to expand...
Click to collapse
i dont get the nav buttons flashing after holding the power button down ( i did it for 2 minutes)
also it was plugged into the htc house charger last night.
the battery terminals where off for at least 5 minutes before this?
reaverclan said:
the battery terminals where off for at least 5 minutes before this?
Click to expand...
Click to collapse
they were off for over 5 hours.
Syntax531 said:
they were off for over 5 hours.
Click to expand...
Click to collapse
Just out of curiosity, what ROM / Kernel were you running when this happened?
Hi guys. Is there any fix for my P7500 tab?
It wont turn on, black screen, but can be detected by the computer via apx.I use to flash it via apx or nvflash but I it was locked tablet. Is there any ways to boot it up so i can flash it via odin?
Thank you in advance for the reply.
psychoneo said:
Hi guys. Is there any fix for my P7500 tab?
It wont turn on, black screen, but can be detected by the computer via adx.I use to flash it via adx or nvflash but I it was locked tablet. Is there any ways to boot it up so i can flash it via odin?
Thank you in advance for the reply.
Click to expand...
Click to collapse
So do you mean adb or apx?
Sent from my GT-P7510 using XDA Premium 4 mobile app
...
stinky73 said:
So do you mean adb or apx?
Click to expand...
Click to collapse
Oh sorry. APX i mean. my question above is now edited. Any idea sir? or i should brought it to samsung service center?
Maybe the only thing to try at the moment would be the old battery drain technique... Usual means is to tape down the power button and wait days and days until it is dead, really dead ( shows nothing when connected to computer), then connect to wall charger and reboot and see what you get. This is really the ultimate "hard reset" but same result can be obtained far more quickly by removing the back and disconnecting the battery for a while to remove residual charge... Not as frightening or difficult as it might seem, have done it loads of times for various faults and to replace batteries in several tabs.
Sent from my GT-P7510 using XDA Premium 4 mobile app
onoeowh eye
stinky73 said:
Maybe the only thing to try at the moment would be the old battery drain technique... Usual means is to tape down the power button and wait days and days until it is dead, really dead ( shows nothing when connected to computer), then connect to wall charger and reboot and see what you get. This is really the ultimate "hard reset" but same result can be obtained far more quickly by removing the back and disconnecting the battery for a while to remove residual charge... Not as frightening or difficult as it might seem, have done it loads of times for various faults and to replace batteries in several tabs.
Click to expand...
Click to collapse
thank you sir. Im doing it now. But Im a doing it correctly? i just connected it to the computer for apx mode then after that i tape the power button so that it continuously on and off for apx mode then i disconnected it to the computer or I should leave it stay? i think it will charge if i connected it to the computer.
If you're trying to discharge by taping down power button just leave the tab on it's own not plugged into anything... Plugging into something that charges rather defeats the object of the exercise
Sent from my SGP311 using XDA Premium HD app
Samsung Service Center
Thank you for the help. I think I need to bring it to service center. There's no battery charging icon when I charged it. I dont know if its well drain but I use a laptop cooling fan via OTG to drain it. the fan and the lights from the cooling pad is not functioning anymore so i try to plug the tab to the wall charger and nothing happens.
By the way thank you. :good:
Any luck?
psychoneo said:
Thank you for the help. I think I need to bring it to service center. There's no battery charging icon when I charged it. I dont know if its well drain but I use a laptop cooling fan via OTG to drain it. the fan and the lights from the cooling pad is not functioning anymore so i try to plug the tab to the wall charger and nothing happens.
By the way thank you. :good:
Click to expand...
Click to collapse
I'm facing the same issue now, i have taped my power and volume button for a day... will that work? Did you finally turn on your tablet?
omeshls said:
I'm facing the same issue now, i have taped my power and volume button for a day... will that work? Did you finally turn on your tablet?
Click to expand...
Click to collapse
In some cases it takes more than a day, be patient... Unless you are prepared to remove the back and unplug battery... The aim of the game is to completely power down the tab and remove residual charge in components, the "hardest" reset available.... So, two ways to achieve that is drain battery or disconnect battery... If you drain battery you must be sure it's empty to achieve desired effect then you obviously cannot restart it without charging a bit as the battery is empty, so you connect charger then try to boot, but the tricky bit is being sure the battery is completely drained otherwise you are just wasting your time... That is why battery disconnect is preferable
Sent from my SGP311 using XDA Premium HD app
How to disconnect battery
stinky73 said:
In some cases it takes more than a day, be patient... Unless you are prepared to remove the back and unplug battery... The aim of the game is to completely power down the tab and remove residual charge in components, the "hardest" reset available.... So, two ways to achieve that is drain battery or disconnect battery... If you drain battery you must be sure it's empty to achieve desired effect then you obviously cannot restart it without charging a bit as the battery is empty, so you connect charger then try to boot, but the tricky bit is being sure the battery is completely drained otherwise you are just wasting your time... That is why battery disconnect is preferable
Sent from my SGP311 using XDA Premium HD app
Click to expand...
Click to collapse
How do you disconnect the battery to discharge. I tried the taped power button for five days and it still seen by PC in Device Manager.
datastar said:
How do you disconnect the battery to discharge. I tried the taped power button for five days and it still seen by PC in Device Manager.
Click to expand...
Click to collapse
Suggest you go here http://forum.xda-developers.com/showthread.php?t=2325109 download the manual - then unplug the battery for 10 mins or so to remove any residual power, reconnect and see what happens
Good luck
Edit....I got beat to the post. I would follow the advice above first.
datastar said:
How do you disconnect the battery to discharge. I tried the taped power button for five days and it still seen by PC in Device Manager.
Click to expand...
Click to collapse
Look for some videos on YouTube because it involves removing the back of your tab. So see seeing it done is a great help.
Sent from my GT-P5210 using XDA Premium HD app
Happy camper iFixIt
stinky73 said:
Suggest you go here http://forum.xda-developers.com/showthread.php?t=2325109 download the manual - then unplug the battery for 10 mins or so to remove any residual power, reconnect and see what happens
Good luck
Click to expand...
Click to collapse
Many Thanks to You stinky73
I had to purchase an iFixIt repair kit to get the correct driver to remove the two screws. I disconnected the battery, waited ten minutes and when I reconnected I was SO HAPPY to see the battery charging icon. I charged for a while a fired up the tablet. Everything was the same as if nothing happened. I am so happy because Samsung said they could fix the problem and it would be a flat rate of $150 which I don't have and I would lose everything.
Many thanks
datastar said:
Many Thanks to You stinky73
I had to purchase an iFixIt repair kit to get the correct driver to remove the two screws. I disconnected the battery, waited ten minutes and when I reconnected I was SO HAPPY to see the battery charging icon. I charged for a while a fired up the tablet. Everything was the same as if nothing happened. I am so happy because Samsung said they could fix the problem and it would be a flat rate of $150 which I don't have and I would lose everything.
Many thanks
Click to expand...
Click to collapse
How hard was removing the back? I'm wanting to do some building for my 7510 and will be using it for testing so I'm most likely to brick it at least once or twice.
Hard screw removal
Benzoman said:
How hard was removing the back? I'm wanting to do some building for my 7510 and will be using it for testing so I'm most likely to brick it at least once or twice.
Click to expand...
Click to collapse
It took me longer to remove the screws then anything. I stripped them and will need to replace them. I tried a regular screwdriver before the tri-wing screw driver and paid dearly in time. Once the two screws were removed, use a plastic pry tool starting on the bottom where the screws are because once the bottom and sides are pried lose, the top will slide over the extended audio jack.
1.5 hours to remove stripped screws
10 minutes to pry open
1 minute to disconnect battery (did not remove battery or three data cables on top of battery)
10 minutes wait for discharge
3 minutes to re-connect battery cable (it slides forward and snap down)
2 minutes to replace case
datastar said:
Many Thanks to You stinky73
I had to purchase an iFixIt repair kit to get the correct driver to remove the two screws. I disconnected the battery, waited ten minutes and when I reconnected I was SO HAPPY to see the battery charging icon. I charged for a while a fired up the tablet. Everything was the same as if nothing happened. I am so happy because Samsung said they could fix the problem and it would be a flat rate of $150 which I don't have and I would lose everything.
Many thanks
Click to expand...
Click to collapse
Happy for you, it usually works!! :good:
stinky73 said:
Happy for you, it usually works!! :good:
Click to expand...
Click to collapse
Forgive the gravedigging, but I am unable to find anything regarding my situation, and the original poster has a problem that is similar to mine (my thread is http://forum.xda-developers.com/showthread.php?p=52931715 ). I hope someone is able to give me a hand here!
I am wondering, it has been over 15 minutes since I disconnected the battery completely, but connecting the P7500 to my laptop still shows an APX device being connected. Could there be some hardware issue preventing the device from being fully discharged?
Thanks in advance for any help!
Still no joy with waking the tablet up
Lightside said:
Forgive the gravedigging, but I am unable to find anything regarding my situation, and the original poster has a problem that is similar to mine (my thread is http://forum.xda-developers.com/showthread.php?p=52931715 ). I hope someone is able to give me a hand here!
I am wondering, it has been over 15 minutes since I disconnected the battery completely, but connecting the P7500 to my laptop still shows an APX device being connected. Could there be some hardware issue preventing the device from being fully discharged?
Thanks in advance for any help!
Click to expand...
Click to collapse
I've got the same issue as Lightside and the original poster. Mine is a GT-P7500, which had CM10 nightly ROM with CWM recovery. I sold it on eBay, but before selling, I wiped the tablet and got it back to the Clockworkmod main screen. I turned it off completely and shipped it to the buyer, ready for it to be registered by the new user.
The buyer received the tablet and from the e-mails I received from him in the first couple of days, all was going well. Then, a couple of days later, he sent me an e-mail saying that the screen shows the android lying on its back with "Odin download" mode showing. A day later, he sends me a messaging saying that he can't turn the tablet on at all. The guy who bought it is an old man and didn't know much about fixing the issue. I asked him whether he powered the tablet off while still plugged in to the wall charger and he confirmed that he did. I asked him to return it to me and I can try and fix it, so now, I have the tablet back and it won't turn on. Here's what is happening:
1. I drained the battery using the cellotape method
2. Installed the NVflash drivers
3. Waited for the battery to drain (almost 9 days and the LED flash stopped blinking, so assumed it was completely drained)
4. Plugged it in to the PC and it immediately showed up again as a device under the USB controllers within Device Manager
5. I then unplugged the battery by opening the back of the tab, left it for 15 mins, then tried the wall charger again, but nothing. No charging icon on the screen.
When I try to press the power button, I can see the LED light up, but the screen is still blank.
Could this be a hardware issue and if so, what do you think could have caused it?
Could really do with some help here, folks! I don't want to have to give the buyer a refund because technically, he got it when it was in working condition and he probably did something to screw it up, but since he's an old man, I thought I'd try and help him, if I can.
same to me
someshj1577 said:
I've got the same issue as Lightside and the original poster. Mine is a GT-P7500, which had CM10 nightly ROM with CWM recovery. I sold it on eBay, but before selling, I wiped the tablet and got it back to the Clockworkmod main screen. I turned it off completely and shipped it to the buyer, ready for it to be registered by the new user.
The buyer received the tablet and from the e-mails I received from him in the first couple of days, all was going well. Then, a couple of days later, he sent me an e-mail saying that the screen shows the android lying on its back with "Odin download" mode showing. A day later, he sends me a messaging saying that he can't turn the tablet on at all. The guy who bought it is an old man and didn't know much about fixing the issue. I asked him whether he powered the tablet off while still plugged in to the wall charger and he confirmed that he did. I asked him to return it to me and I can try and fix it, so now, I have the tablet back and it won't turn on. Here's what is happening:
1. I drained the battery using the cellotape method
2. Installed the NVflash drivers
3. Waited for the battery to drain (almost 9 days and the LED flash stopped blinking, so assumed it was completely drained)
4. Plugged it in to the PC and it immediately showed up again as a device under the USB controllers within Device Manager
5. I then unplugged the battery by opening the back of the tab, left it for 15 mins, then tried the wall charger again, but nothing. No charging icon on the screen.
When I try to press the power button, I can see the LED light up, but the screen is still blank.
Could this be a hardware issue and if so, what do you think could have caused it?
Could really do with some help here, folks! I don't want to have to give the buyer a refund because technically, he got it when it was in working condition and he probably did something to screw it up, but since he's an old man, I thought I'd try and help him, if I can.
Click to expand...
Click to collapse
i have a GT-7500 ,i used the original firmeware,it's the same issue,drain battery method not working,somebody help?
This morning, my Z ultra died on me. It wont start, no vibration, no use pressing vol + power buttons and the red switch. I was neither rooted or bootloader unlocked.
When I tried to connect it to my laptop (Windows 7), its shows as a USB device. The red LED flashes up, the computer finds it and then lets go of it again. Again in a few minutes, the red LED goes up , the computer makes the connection sound and then the red LED goes off again. This cycle goes on and on.
I cannot use SEUS, Flash, Fastboot or do anything. I have checked various forums and apparently I have not hard bricked the phone as the LED still works and the computer recognizes the problem. But no one has given any concrete solution.
When I connect it to the charger which came with the phone, the red LED pops up and then goes off again. I dont know if its charging. HOWEVER, I have used another Chinese Travel Charger, and then the red LED stays solid as if its charging. I dont know what it means.
Please help. I spent a lot behind this phone. I dont want to be left with a brick
It's not an issue if it's completely stock is it? You have your warranty, but i understand that i sucks to have it shipped in for repairs for god knows how long. I had a similar issue some time ago, but i'm bootloader unlocked and what not, so that was pretty easy to fix. You're completely stock though, so it's a little harder to do anything.
What happens if you hold VOL UP when you connect it to your computer? Does a blue LED light up? If yes, does it stay on, or does it disappear? What happens if you hold VOL DOWN when you connect it to your computer? Do you get a blinking LED and then nothing? That's normal, and it's going into Flashmode. If you can get it to stay in Flashmode you'll be able to re-flash a ROM in Flashtool. But be 100% sure to have enough battery, or else you'll be in danger of hard bricking it.
So..
- Plug the wall charger in and charge it for a couple of hours (2-3 hours)
- Try to kick it into Fastboot (VOL UP when you connect it to your computer). Look for blue LED.
- Try to kick it into Flashmode (VOL DOWN when you connect it yo your computer). No LED.
Hi LordManhattan. I dont have any warranty as I brought it from a local reseller .
Whether I press Vol UP or vom DOWN when I connect to the laptop, a red LED pops up, there is a connection sound and after that the red LED goes off and and there is a disconnection sound.
If I leave the phone connected with the computer, the phone gets connected after 2/3 minutes, there is a connection sound and then there is a disconnection sound again . Any clue what I can do :crying::crying:
LordManhattan said:
It's not an issue if it's completely stock is it? You have your warranty, but i understand that i sucks to have it shipped in for repairs for god knows how long. I had a similar issue some time ago, but i'm bootloader unlocked and what not, so that was pretty easy to fix. You're completely stock though, so it's a little harder to do anything.
What happens if you hold VOL UP when you connect it to your computer? Does a blue LED light up? If yes, does it stay on, or does it disappear? What happens if you hold VOL DOWN when you connect it to your computer? Do you get a blinking LED and then nothing? That's normal, and it's going into Flashmode. If you can get it to stay in Flashmode you'll be able to re-flash a ROM in Flashtool. But be 100% sure to have enough battery, or else you'll be in danger of hard bricking it.
So..
- Plug the wall charger in and charge it for a couple of hours (2-3 hours)
- Try to kick it into Fastboot (VOL UP when you connect it to your computer). Look for blue LED.
- Try to kick it into Flashmode (VOL DOWN when you connect it yo your computer). No LED.
Click to expand...
Click to collapse
LordManhattan said:
- Plug the wall charger in and charge it for a couple of hours (2-3 hours)
- Try to kick it into Fastboot (VOL UP when you connect it to your computer). Look for blue LED.
- Try to kick it into Flashmode (VOL DOWN when you connect it yo your computer). No LED.
Click to expand...
Click to collapse
just a small note or two:
Flashmode the LED should go orange, then blue then off within about 1second then it is in Flashmode
To get into either of these modes the phone has to be powered fully OFF, press the red reset button before charging to make sure, then again just before the above steps.
It sort of sounds like a corrupted loader
showdown_counts said:
Hi LordManhattan. I dont have any warranty as I brought it from a local reseller .
Whether I press Vol UP or vom DOWN when I connect to the laptop, a red LED pops up, there is a connection sound and after that the red LED goes off and and there is a disconnection sound.
If I leave the phone connected with the computer, the phone gets connected after 2/3 minutes, there is a connection sound and then there is a disconnection sound again . Any clue what I can do :crying::crying:
Click to expand...
Click to collapse
Hmmm... This is a tough one..
Sent from my C6806_GPe using Tapatalk
Please someone help me. Really need to do something here
LordManhattan said:
Hmmm... This is a tough one..
Sent from my C6806_GPe using Tapatalk
Click to expand...
Click to collapse
Have a good read of this? http://forum.xda-developers.com/showthread.php?t=1849170
It would suggest that the battery is flat. Let it charge in the wall plug for a few hours and see what happens
I have let the phone to charge overnight with the charger that came with the phone. As I said before, with that charger, the red LED would turn on and then go off again. I will hopefully try the Chinese travel charger tonight with which the red LED remains solid.
The funny thing is , the phone had about 80% charge when it died. This is so weird :'(
What You Do Before It Happen?
Sent from my C6833 using Tapatalk
Nothing. Its like as if the phone soft bricked itself, probably by auto updating or something
showdown_counts said:
Nothing. Its like as if the phone soft bricked itself, probably by auto updating or something
Click to expand...
Click to collapse
Have you tried the reset button under the microsd flap? Press and hold for 3 secs.
I did read another user had an issue where the screen blanked for around a day, he left it plugged in and came back to it about 6 hours later and it was fine again.
Sent from my C6833 using XDA Premium 4 mobile app
I tried that and basically all the other normal options. No use. The computer recognises it as a USB Input Device and for a second or two, the red LED comes up. Same thing when I am charging
SpyderTracks said:
Have you tried the reset button under the microsd flap? Press and hold for 3 secs.
I did read another user had an issue where the screen blanked for around a day, he left it plugged in and came back to it about 6 hours later and it was fine again.
Sent from my C6833 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
showdown_counts said:
I tried that and basically all the other normal options. No use. The computer recognises it as a USB Input Device and for a second or two, the red LED comes up. Same thing when I am charging
Click to expand...
Click to collapse
It's a battery issue most probably. I guess it doesn't show anything. Is your battery removable?
I still have not opened my phone. I am looking at all the other options first. If everything else fails, I guess I will have to open my phone
showdown_counts said:
I still have not opened my phone. I am looking at all the other options first. If everything else fails, I guess I will have to open my phone
Click to expand...
Click to collapse
I know it isn't the best choice but I would suggest getting it to sony repair. So that your waranty isn't voided (even if you have bought from a local store you still have waranty
Andrewasth said:
I know it isn't the best choice but I would suggest getting it to sony repair. So that your waranty isn't voided (even if you have bought from a local store you still have waranty
Click to expand...
Click to collapse
Warranty exists with Sony for first year, no matter where it's bought, very true.
Sent from my C6833 using XDA Premium 4 mobile app
+1 contact your local sony, i had a similar problem, no fastboot/flashmode. locked bl/not rooted and my led only flashed red and occasionally solid red then nothing. plugging it into computer continuously played the disconnecting sound.
most likely hardbricked.
i also purchased my xzu from a local BST but as long as you have your imei, contact sony and theyll tell you if you have warranty. they required me to send in proof of purchase as well but like most say "play stupid" ( i said i received it as a gift and they said it was fine)
i got a brand new XZU after a week and a half sending it in.
LordManhattan said:
- Plug the wall charger in and charge it for a couple of hours (2-3 hours)
- Try to kick it into Fastboot (VOL UP when you connect it to your computer). Look for blue LED.
- Try to kick it into Flashmode (VOL DOWN when you connect it yo your computer). No LED.
Click to expand...
Click to collapse
Thank you! One or two years ago my Z Ultra's screen cracked and I got a new phone. Decided to use it again, purchased a new screen and replaced it myself today. When I tried to move to AOSP (had root, bootloader unlocked, backup of TA partition), the phone bricked. No SONY logo, nothing. Did what you said above, Xperia Companion recognized the phone in flashmode and is now downloading the newest stock rom. I was so afraid of a hard brick, that living with latest stock without root doesn't seen so bad now hahaha
Hey Friends, I have exactly the same issue. The red led just flashes up for a couple of seconds and this cycle continues. My battery was a bit swollen up and the back glass cover opened up a bit. Still battery was working fine. Two days ago I tried nougat aosp on it and after leaving it idle for 2 hours, it was bricked. I can enter into flashmode and flashed stock LP as well as KK but it does not boots up. Is it definitely battery's problem? If yes, where can I buy original or near original battery for it?
lifehacker69 said:
Hey Friends, I have exactly the same issue. The red led just flashes up for a couple of seconds and this cycle continues. My battery was a bit swollen up and the back glass cover opened up a bit. Still battery was working fine. Two days ago I tried nougat aosp on it and after leaving it idle for 2 hours, it was bricked. I can enter into flashmode and flashed stock LP as well as KK but it does not boots up. Is it definitely battery's problem? If yes, where can I buy original or near original battery for it?
Click to expand...
Click to collapse
The battery is dangerous and should be removed. Be careful because the battery can burst into flames if the bloated cell get punctured.
Use tools with caution and take your time.
Lipo cells expands as a first safety trigger. Instead of going strait to venting or venting and burst into flames.
Its a safety feature if they are charged with too high current or if the cell is drained below its 2,22 volts and is brought back to life with a normal charger that puts normal current on the cell. Then even 400mA in this scenario is way too much current to start charging a drained cell with.
But the battery should not be the issue that your phone is not booting. How did you flash stock rom? With Flashtool?