Hello everyone, this is my second post in the community and as above, I draw you before the serious problem that has my cell phone and that despite the help of all of you still not solved enclose descriptions videos and fails the steps and followed over time. :crying::crying:
All this happened when installing from retail jb rom ics one Chinese, after the installation the cell began to discharge too fast to the point of completely unloaded and not turn over, the next thing was wired switch it could enter the factory and then recovery only restarted.
after the above procedure to unbrick with Unbrick method & switch to 982.124.14.XT910.Retail.en.EU with which obtube not any response, after that a user community graciously offered to assist and I sending the same procedure but with the files for my region (Latam) after that the phone showed the motorola logo and restarted but at times passed motorola logo and showed the animated logo motorola, encendia the lights cell buttons and screen bottom came out "Wait a minute" restarted (enclose one. rar with videos of procedures performed and detailed information.
I count on your help and already thank you very much for reading my topic and I hope to get my phone I need too :crying:
:victorydt: my apologies for the bad drafting but all this is performed with English translator (I'm from chile) :laugh::laugh:
Hi,
Based on your video, I haven't see you flashed with RSD Lite and fastboot file.
You can give a try based on this thread:
http://forum.xda-developers.com/showthread.php?t=2231289
Download LATAM fastboot file (Chile should be latam right?) and download also latest rsd lite ver 6.1.4
Good luck and hope it will unbrick your phone.
idwijayaku said:
Hi,
Based on your video, I haven't see you flashed with RSD Lite and fastboot file.
You can give a try based on this thread:
http://forum.xda-developers.com/showthread.php?t=2231289
Download LATAM fastboot file (Chile should be latam right?) and download also latest rsd lite ver 6.1.4
Good luck and hope it will unbrick your phone.
Click to expand...
Click to collapse
reaches the motorola dual core logo and restarts :crying::crying:there some method other than by fasboot?, or some solution?
Have you download fastboot files that match with you region? if yes then you have same issue with me
So far what I know to flash is use batch file that developed by awesome developers here and RSD lite.
Have you try this:
- Go to boot menu (the way you get AP Fastboot menu) but this time try to select BP Tools
- and wait will your phone able to boot into system or not... If you able to boot into bp tools, get your phone root (JB is able for root now, get the thread in development), then install BMM to have it normal boot .. I got this suggestion but never able to have my phone boot in BP Tools, so I never know this works or not so good luck
- When you choose BP Tools and your phone still on M logo turn it off (you should wait only 10 or 15 minutes max) then turn off your phone and put it in boot menu to select BP HW Diag.. then.. we have same issue.. be prepare your phone only able to phone call , sms , taking camera, cannot access data only rely wifi , USB debugging not working, some fastboot files makes your phone not able to charge (I have to turn off my phone then charge)
I still strugling to have my phone back to normal also..
idwijayaku said:
Have you download fastboot files that match with you region? if yes then you have same issue with me
So far what I know to flash is use batch file that developed by awesome developers here and RSD lite.
Have you try this:
- Go to boot menu (the way you get AP Fastboot menu) but this time try to select BP Tools
- and wait will your phone able to boot into system or not... If you able to boot into bp tools, get your phone root (JB is able for root now, get the thread in development), then install BMM to have it normal boot .. I got this suggestion but never able to have my phone boot in BP Tools, so I never know this works or not so good luck
- When you choose BP Tools and your phone still on M logo turn it off (you should wait only 10 or 15 minutes max) then turn off your phone and put it in boot menu to select BP HW Diag.. then.. we have same issue.. be prepare your phone only able to phone call , sms , taking camera, cannot access data only rely wifi , USB debugging not working, some fastboot files makes your phone not able to charge (I have to turn off my phone then charge)
I still strugling to have my phone back to normal also..
Click to expand...
Click to collapse
did not work :crying::crying: still coming to dual core logo and restarts, other help......
Esto.Vir said:
did not work :crying::crying: still coming to dual core logo and restarts, other help......
Click to expand...
Click to collapse
Reflash the appropriate fastboot once again and then reboot into stock recovery and do fill wipe data and chaches . It may fix ya problem
Thx
Hit the thx button if i helped ya in anyways
anurag.dj2u said:
Reflash the appropriate fastboot once again and then reboot into stock recovery and do fill wipe data and chaches . It may fix ya problem
Thx
Hit the thx button if i helped ya in anyways
Click to expand...
Click to collapse
and tested with the brazil retail rom, fido, rogers ye had the same problem, my question is, if all the rom's the same that another problem will have my phone? , I can enter the ap fastboot recovery and all that d the stock recovery, my phone stayed brick to install a Chinese jb rom this tutorial :
http://www.chileandroid.com/t16992-romxt910jelly-bean-jelly-bean-41-2-china-retail-oficial
, Change kernel and everything that goes in the guide, that will be a problem? I hope you can help me from now thank you very much:crying::crying:
Related
Hey Guys
I was flashing my phone using RSD Lite, when suddendly the flash program got stuck. So i powerd off my phone, but now everytime I start it the AP Fastboot Flash Mode (S) (Flash Failure) screen comes up.
What to do?!
Nevermind, the flash worked now
How did you get it to work? Same thing just happened to me and can't figure out how to reflash, RSDLite fails and so does Kholk's alternative
I am having the same problem. stuck at the AP fastboot flash mode
says invalid cdt
at the bottom it says
invalid cg version (cg:cdt)
PLZ any help before my battery dies
I also used rsd lite
Oh I was using the search and seen he was having the same problem but did not notice he has the razor I have the Bionic
Hey Man...power down the phone. Go to the dev thread of razr and look for my one click restore and download it.. my tool should solve ur problem
Sent from my DROID RAZR using XDA App
Do you have a link as i can't find it...
I am having the same problems...
Thank you
cool-freebies
coolfreebies said:
Do you have a link as i can't find it...
I am having the same problems...
Thank you
cool-freebies
Click to expand...
Click to collapse
Just search for his name in that forum.
http://forum.xda-developers.com/showthread.php?t=1451205&highlight=globed
Refreshing
Got the same problem.
Stuck in AP Fastboot mode while charging my mobile. I'm currently runing stock ICS for UK.
I can flash razr via RSD Lite, but nothing happend even if rsd says passed.
Can run Boot mode selection menu, but can't chose any option
If reset the phone with power+volume down it gets again in AP Fastboot
Does anyone can help me. Please!
Can you provide more details ?
jazzone said:
Refreshing
Got the same problem.
Stuck in AP Fastboot mode while charging my mobile. I'm currently runing stock ICS for UK.
I can flash razr via RSD Lite, but nothing happend even if rsd says passed.
Can run Boot mode selection menu, but can't chose any option
If reset the phone with power+volume down it gets again in AP Fastboot
Does anyone can help me. Please!
Click to expand...
Click to collapse
hi mate,
provide more details + some screenshots, and definitely someone ( if not me ) can get you out of this.
Also try to move this thread to Q&A section
I can't make any screen shot couse i stuck in AP Fastboot mode. I can't flash my phone via RSD Lite. Battery is OK, USB connected.
What kind of inormation do You need?
Thanks for help.
I know the thread is in wrong section but I didn't start it.
I'm asking Mods to move it please to CandA place.
Well I got myself into it this time. I have a Rogers Canada XT910 razr. I installed the Arctic rom and lost all my data connection, and all my apps and could not reload them from google play because it says they are already installed. So I did a wipe and reset and decided to try to use RSD to reflash the ics leak. The flash failed, and my phone is bricked. What's guy to do.
Thanks
John
http://forum.xda-developers.com/showthread.php?p=27944788
That's the leak you need I guess.
There's just one Problem. You need an patched Boot. Img and the system signed of the necessary GB Rom.
I've not searched this Thread for an boot. Img. Maybe someone posted one.
I'm not sure, if you can flash the European Fastboot Files, to get an working RazR, till there's an solution for you.
Gesendet von meinem XT910 mit Tapatalk 2
Thanks man. I had already side loaded the leak that you had linked to so I was on ics before I tried the arctic. I will try tonight to install the European version. I'll let you know how it goes.
Well I am at my wits end.
I eventually got my phone to reboot back into the Arctic rom I loaded, but can't figure out how to update this rom or load another. I have tried with RSD to flash a different flashboot files, but they all fail. I have down loaded a few different custom roms and loaded them on my sd card and tried updating my phone from external storage through the Android system recovery utility but action is always aborted. I can't load any apps like rom manager, file manager, or anything for that matter. When I go to the play store and look at my apps it says i already have them all installed and can't load any. What can I do?
Well I can't seem to leave well enough well enough. tried a few more things and now the phone won't boot. It gets to the Motorola logo and turns off. So can I can get to fastboot and recovery or off. Brutally expensive paper weight.
Can help
hammily said:
Well I can't seem to leave well enough well enough. tried a few more things and now the phone won't boot. It gets to the Motorola logo and turns off. So can I can get to fastboot and recovery or off. Brutally expensive paper weight.
Click to expand...
Click to collapse
I bricked my Rogers RAZR too and was able to fix it. It's a matter of finding the correct signed img and flashing it using the fastboot (when starting phone press power and hold volume up if I remember correctly). Will check what the name of the image is and get back to you. I flashed three or so different images before it would finally boot, then I was able to re-root it, install CWM and get back on my feet.:good:
The rom I loaded is European from here.
http://forum.xda-developers.com/showthread.php?t=1760702
I have been bricked before and fixed the issue, but after loading this custom rom the flash I used the first time with RSD does not work. I appreciate any help and I am willing to try what ever. I did not impress my wife with this one.
flash this
http://forum.xda-developers.com/archive/index.php/t-1634223.html
then reboot....it will work
Thanks I will try it after I get home from work today.
[TUTORIAL]
1. Download the empty_radio.img
2. Turn off the Razr
3. Power On the Razr and select Fastboot Mode AP
4. Open the command prompt CMD
5. Go to the folder where the radio is empty
6. Make flash the radio with the following command and then type "fastboot reboot"
7. Rest assured I tested on my Razr this command does not erase the radio
8. This command will only restart the fastboot
9. Now then turn off the Razr holding vol - and power
10. Plug the Razr holding vol + vol - and power and have it start normally
11. Now restart the fastboot screen will not show more ...
This stuff is over my head. I don't know how to do steps 4,5,6. I don't know what to do in command prompt, I can't find the folder where the radio is empty, and I don't know how to flash the radio. I am totally lost.
Does any body have any other Ideas?
Have you tried fastboot with rsd lite?
Sent from my DROID RAZR using xda premium
Yes I have tried flashing several different XML files from different ROM's With RSD lite 5.7. The flash always fails. In RSD it says that my phone is connected, but it does not show my IMEI it just has N/A in that box. When I hook up my wife's phone which is totally stock it does show her IMEI. Could this be part of the problem?
Hi everyone here, i'm not trying to be noob here(if i am please forgive me), i search many many post, and no one with the same situation with me, so i had to ask here:crying:
I'm on Official MIUI 2.9.14 ICS build, and i wanna go back to stock ICS due to Lapdock compatibility. And this is the scenario.
I'm on Asia Retail 2.3.6 before that, flash follow MIUI Official guide, flash a EU Retail via RSD lite as following,
SPDREM_U_01.6.5.1-167_SPU-15-M2-3_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot.xml
then razr_4.04_europe_ota, then MIUI
so, back to what just happened, i try to go back to stock via RSD Lite again, since i flash a EU Retail before, and been told that it is impossible to back to GB, should back to ICS, then i assumed that i should flash back
SPDREM_U_01.6.5.1-167_SPU-15-M2-3_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot.xml,
so after decompressed, and flash, it got me back FLASH FAILURE.... YAY.... Fastboot Loop.... Phone LOCKED, Status 0
then i found the way to charge my battery, phewww. but..... i found one more thing, in RSD Lite, while i connect my phone in fastboot mode,
My phone is detected, status Conected, BUT.... in the above ESN, Technology, Software Version, Flex Version, DRM Version, Bootloader Version, Phone Type... ALL APPEARED as N/A
Now a charging RAZR, fastboot loop, i'm downloading Asia Retail 2.3.6, Downloading RAZR Utility(Seems like no use to me?)
Any suggestion what should i do?
RSD Lite, fastboot mode, flash Asia Retail 2.3.6?
or
RSD Lite, fastboot mode, flash Eternity Project Final ICS Eu Retail?
A very very thanks in advance, and please forgive my poor grammar.
Update : I found that i can go to original recovery (dunno what can do here), and on Boot mode selection(Volume UP+DOWN+Power), i can scroll down to BP HW Diag & Boot AP, then i can boot up my original MIUI, but it cant connect to pc using USB nor Charging on wall plug, USB not functioning, kinda weird, then i reboot again (Volume UP+DOWN+Power), this time enter BP Tools, yay... this boot up the MIUI too, but with functioning USB DATA+Charge... but everytime i reboot the RAZR, it ends up stuck at AP Fastboot Bootloop, i had to use the method (Volume UP+DOWN+Power) to boot up correctly, and if i do the (Volume UP+DOWN+Power), i wait for 10-15 secs, it will also automaticlly boot to MIUI with functioning USB.
Now what? LMAO..... what should i do? any expert here can tell me what to do? How to get back to stock ICS? using bootstrap recovery? using original recovery? using RSD Lite?
The same problem... Today...Any other fastboot file link maybe?
I flash with rsd: SPDREM_U_01.6.7.2-180_SPU-19-TA-11.2_SIGNEuropeAustraliaEMEA
Im in hungary, in europe.
Edit:
I install this via rsd lite:
http://www.eternityproject.eu/topic...-official-fastboot-package-for-motorola-razr/
Before this it is work all the time... But from miui now.... bootloop. :\
And no standard original recovery. It shows me an android and a "!" character. Any idea?
Edit2:
DONE!
I use this:
http://www.eternityproject.eu/topic/15-gsmcdma-eternityprojects-rsd-alternative-for-flashing/
And flash the same rom. when its finish, the phone's screen shows me that andoid and the "!" character... I push (random) volume buttons, and appears the stock recovery. Press Factory reset, then reboot and now i have a stock ics. Work.
Now i install the MagicICS. See what happens.
Hello, yesterday while trying to encrypt a folder in the internal memory in the beta program, I discovered to my horror that the entire internal memory(sdcard) have been erased. I do not know how or why. After reset, the overhang on the logo. I have uploaded JB o2, retail Europe, does not start up the phone. Overhang on the logo or bootloop. I try this http://forum.xda-developers.com/showthread.php?t=2505254. In the end I took the tutorial in this topic http://forum.xda-developers.com/showthread.php?t=2194825&highlight=unbrick&page=4, phone starts up but after a reboot bootloop. After re-uploading the Blur files phone starts, but after a reboot bootloop again. Does anyone have any ideas?
Regards
kamel828 said:
Hello, yesterday while trying to encrypt a folder in the internal memory in the beta program, I discovered to my horror that the entire internal memory(sdcard) have been erased. I do not know how or why. After reset, the overhang on the logo. I have uploaded JB o2, retail Europe, does ot start up the phone. Overhang on the logo or bootloop. I try this http://forum.xda-developers.com/showthread.php?t=2505254. In the end I took the tutorial in this topic http://forum.xda-developers.com/showthread.php?t=2194825&highlight=unbrick&page=4, phone starts up but after a reboot bootloop. After re-uploading the Blur files phone starts, but after a reboot bootloop again. Does anyone have any ideas?
Regards
Click to expand...
Click to collapse
First of all stay calm and relax all can be solved....
The best way for flash again the rom is use rds lite
For flash a 4.1.2 you have to use rds lite 6.0 (google it)
Also you need to install the usb drive otherways your razr will not connect perfectly
If you have the 4.1.2 europe try another one like the german retail or the franch one
SO:
Turn off (power botton and vol -)
Let it charge a little bit (half battery will be ok)
enter recovery mode (power vlo- vol+)
go in ap fastboot using vol - and power for confirm
decompress the file you want to flash (in a folder and rename as you like)
launch the rds (remember install mototrala driver)
search the folder where you extract the rom and double click on .xlm file
plug the phone in pc,wait few seconds (10)
click on start
wait
done
some link
rds 6.0 http://forum.xda-developers.com/show...php?p=32900727
Motorola drivers https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth
rom to flash http://forum.xda-developers.com/showthread.php?t=2231289 Retail british work for me
Finger crossed for you
Phone starts after flashing, but after switching off no longer runs. It hangs on a moving logo Motorola. Every few attempts to phone starts up again after a reboot unfortunately hang.Wipe data and cache does not help. I used RSD Lite 6.0, I downloaded the drivers from the Motorola version 2.43, the system is a Retail France from the given topic. Regards and thanks for help.
EDIT:
Phone boot up in BP HW Test mode in stock recovery. After reboot in normal mode phone still bootloop.
Regards
Anyone have any idea? I ran out of ideas. I had installed BBM and Retail JB slot 1 if it has any meaning.
Hi all, so i´ts my first time here posting but I´ve been following this forums long ago and touching stuff with my phones.
Today (well today... i´m working on this since yesterday) I´ll need the help of the most veteran users since I can´t solve this on my own.
I Have an XT910 Razr Moto. Yesterday I charged it with it being off, but to my surprise when I powered it on, I got the Fastboot screen saying the device is locked. Here´s the complete error:
-----------
AP Fastboot Flash Mode (S)
0A.74
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
Battery Ok
Ok to Program
Connect USB Data cable.
-----------
So, after getting this, obviously I thought, well, power off, or force power off, then power it on, and lets go... Well, nothing, I constantly get into Fastboot again.
What I figured out is that if I power it off, then hold vol down + vol up and power at the same time, I actually CAN get into boot menu but It will not let me select anything, it will just show it and boot in Safe Mode for me.... Tried factory reset also, so i could backup everything...
After going through all that I decided to give it a try and go for RSD with stock firmwares from sbf.droid-developers.org. I got like 4 and they all stucked at cdt.bin flashing part... Giving me an error about 6/18 process that can´t flash cdt.
So far I´ve tried LOTS LOTS of stuff like some .zip going around there to fix the CDT, with no luck...
THen I ran into this post
http://forum.xda-developers.com/showthread.php?t=1651596
Which was very usefull to have some progress, like completing the flash by erasing some lines in the xml about the cdt. system (cause it hung a lot there and gave error again)...
However, the error still persists, I boot up my damn phone and it goes into AP Fastboot. When i go into Safe Mode I see that everything has been wiped so its like a factory phone now, but still in safe and powering it off won´t make the difference.
I´m kinda desperate and about to throw this phone out of the window. Is there any pro savior out there who can give me more tips?
Thanks!!!!!!!!!
-Musashi- said:
Hi all, so i´ts my first time here posting but I´ve been following this forums long ago and touching stuff with my phones.
Today (well today... i´m working on this since yesterday) I´ll need the help of the most veteran users since I can´t solve this on my own.
I Have an XT910 Razr Moto. Yesterday I charged it with it being off, but to my surprise when I powered it on, I got the Fastboot screen saying the device is locked. Here´s the complete error:
-----------
AP Fastboot Flash Mode (S)
0A.74
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
Battery Ok
Ok to Program
Connect USB Data cable.
-----------
So, after getting this, obviously I thought, well, power off, or force power off, then power it on, and lets go... Well, nothing, I constantly get into Fastboot again.
What I figured out is that if I power it off, then hold vol down + vol up and power at the same time, I actually CAN get into boot menu but It will not let me select anything, it will just show it and boot in Safe Mode for me.... Tried factory reset also, so i could backup everything...
After going through all that I decided to give it a try and go for RSD with stock firmwares from sbf.droid-developers.org. I got like 4 and they all stucked at cdt.bin flashing part... Giving me an error about 6/18 process that can´t flash cdt.
So far I´ve tried LOTS LOTS of stuff like some .zip going around there to fix the CDT, with no luck...
THen I ran into this post
http://forum.xda-developers.com/showthread.php?t=1651596
Which was very usefull to have some progress, like completing the flash by erasing some lines in the xml about the cdt. system (cause it hung a lot there and gave error again)...
However, the error still persists, I boot up my damn phone and it goes into AP Fastboot. When i go into Safe Mode I see that everything has been wiped so its like a factory phone now, but still in safe and powering it off won´t make the difference.
I´m kinda desperate and about to throw this phone out of the window. Is there any pro savior out there who can give me more tips?
Thanks!!!!!!!!!
Click to expand...
Click to collapse
What fastboot files did you tried to flash?Were you on ICS or JB before the brick?Where are you from?
Error 6 means that you are trying to flash wrong firmware,for example,you was on JB and now you want to flash ICS.
Here are JB Fastboot files http://forum.xda-developers.com/showthread.php?t=2231289,just flash one for your region.
welder73 said:
What fastboot files did you tried to flash?Were you on ICS or JB before the brick?Where are you from?
Error 6 means that you are trying to flash wrong firmware,for example,you was on JB and now you want to flash ICS.
Here are JB Fastboot files http://forum.xda-developers.com/showthread.php?t=2231289,just flash one for your region.
Click to expand...
Click to collapse
I´m from Argentina. And you are totally correct, I downloaded FB files for 4.0.4 , but now I tried running the phone in Safe Mode, went to sys info to take a look at it. And found I have 4.1.2
So question is, from that list you gave me, the "Retail Brazil" should do it? as well as UK retail or any other?? Which one should I chose
Thanks!!!!!!!! a lot
welder73 said:
What fastboot files did you tried to flash?Were you on ICS or JB before the brick?Where are you from?
Error 6 means that you are trying to flash wrong firmware,for example,you was on JB and now you want to flash ICS.
Here are JB Fastboot files http://forum.xda-developers.com/showthread.php?t=2231289,just flash one for your region.
Click to expand...
Click to collapse
Ok so I have made quite a progress here. I was able to get a Brazilian version which is from LATAM and RSD flashed straight like a charm. Now I have the clean new firmware.
And even I can read in the fastboot 0A.77 instead of 0A.74 version
HOWEVER: problem with the Fastboot still persists. Even the phone itself when it restarts goes into Fastboot and when I´m able to make a boot menu I can´t choose anything and it goes directly to Safe Mode.
Now that the system´s """""fixed"""" and I could flash it.... Any tips on taking this off? I cant start the phone in normal mode :S