Related
The gist of my problem: Earlier today I successfully installed the latest CM9 from Joker (.0.7.0.0). Unfortunately, all wireless services other than WIFI were down (including SMS and telephone), and on start the phone produced an error about the com.android.phone force closing (or some such). I figured I had screwed something up, so I reflashed the clean stock firmware.
Since then (roughly 12 hours ago), I've been getting the stuck on the boot screen whenever I try flashing CM9. Relevant details follow:
Logcat doesn't help -- it tosses an error about the shell directory or file not being found (the exact error message escapes me, but I can reproduce it if need be).
I've tried formatting cache, data, and system, followed by a wipe (or two) on several occasions.
I've also tried flashing various versions of CM9 -- specifically .0.7.0.0 and .3.1. Both give the same result. I've also tried whatever version is in the KitchenSink v2.11 installer. Same result.
My CMW version is the 5.0.2.8. I installed it through RomManager (as opposed to the command prompt on Windows, which I did the first time when it quasi-worked). I've read that using v2 fixes this issue, but I can't find a live copy anywhere, so I haven't been able to try it.
Rather than going for a completely new install every time I bork something, I made a backup just after I finished unlocking and rooting the phone. I just restore that backup after each attempt, and it goes back to working fine on the stock Android firmware (3.whatever).
Any ideas? I think I'll try starting completely from scratch again and not using RomManager tomorrow, but if anyone can point out my error before then and save me a lot of -- hopefully not wasted -- effort, it would be fantastic.
Cheers,
Vash
vash265 said:
The gist of my problem: Earlier today I successfully installed the latest CM9 from Joker (.0.7.0.0). Unfortunately, all wireless services other than WIFI were down (including SMS and telephone), and on start the phone produced an error about the com.android.phone force closing (or some such). I figured I had screwed something up, so I reflashed the clean stock firmware.
Since then (roughly 12 hours ago), I've been getting the stuck on the boot screen whenever I try flashing CM9. Relevant details follow:
Logcat doesn't help -- it tosses an error about the shell directory or file not being found (the exact error message escapes me, but I can reproduce it if need be).
I've tried formatting cache, data, and system, followed by a wipe (or two) on several occasions.
I've also tried flashing various versions of CM9 -- specifically .0.7.0.0 and .3.1. Both give the same result. I've also tried whatever version is in the KitchenSink v2.11 installer. Same result.
My CMW version is the 5.0.2.8. I installed it through RomManager (as opposed to the command prompt on Windows, which I did the first time when it quasi-worked). I've read that using v2 fixes this issue, but I can't find a live copy anywhere, so I haven't been able to try it.
Rather than going for a completely new install every time I bork something, I made a backup just after I finished unlocking and rooting the phone. I just restore that backup after each attempt, and it goes back to working fine on the stock Android firmware (3.whatever).
Any ideas? I think I'll try starting completely from scratch again and not using RomManager tomorrow, but if anyone can point out my error before then and save me a lot of -- hopefully not wasted -- effort, it would be fantastic.
Cheers,
Vash
Click to expand...
Click to collapse
Use this recovery. http://forum.xda-developers.com/showthread.php?t=1218417
Or jokers at http://forum.jokersax.com/discussion/25/joker-recovery-for-the-photon-v3
I use the first link. Works perfect. Once you install the recovery. Wipe everything. Install 0.3.1. Boot into the system. Go back and flash the newest 0.7.0 update with gapps.
Should fix all the issues.
Sent from my SGH-I777 using XDA
Well, I got .3.1 working. Then tried to install .7 and it crapped itself again. Should I have cleared all the data/caches/etc. between the two?
Edit - I tried it again but this time cleared all the data between installs. It booted, but I got the same 'android.phone failed to start' message.
Edit 2 - Alright, I think I got it. I didn't clear anything between the two installs, but I installed each firmware twice without exiting recovery mode either time. It seems to be working (phone works, at least), although I'm not sure my 3G is working...
na7q said:
Use this recovery. http://forum.xda-developers.com/showthread.php?t=1218417
Or jokers at http://forum.jokersax.com/discussion/25/joker-recovery-for-the-photon-v3
I use the first link. Works perfect. Once you install the recovery. Wipe everything. Install 0.3.1. Boot into the system. Go back and flash the newest 0.7.0 update with gapps.
Should fix all the issues.
Sent from my SGH-I777 using XDA
Click to expand...
Click to collapse
Joker's recovery is a zip file you can flash from 5.0.2.8 if you don't feel like hooking up to the computer and using fastboot. But 5.0.2.8 doesn't work right to flash roms.
Sent from my MB855 using xda app-developers app
Aside from not being able to connect to any 3G networks (which is a problem...), it looks like it's working. Any ideas why 3G doesn't work now?
Thanks for the help thus far =)
vash265 said:
Aside from not being able to connect to any 3G networks (which is a problem...), it looks like it's working. Any ideas why 3G doesn't work now?
Thanks for the help thus far =)
Click to expand...
Click to collapse
Install 3.1, boot, reboot to recovery, wipe cache and dalvik, install 7.0, install gapps, boot.
Sent from my MB855 using xda app-developers app
Acvice said:
Install 3.1, boot, reboot to recovery, wipe cache and dalvik, install 7.0, install gapps, boot.
Sent from my MB855 using xda app-developers app
Click to expand...
Click to collapse
Yep...already did that and got it to boot just fine. Now I'm struggling with poor reception. I've seen other users (different phones) mention radio upgrades, but I was extremely unfamiliar with the terminology. The phone seems to work okay, but I only get 1x reception for data.
Or were you actually suggesting to repeat the entire process?
Edit - Tried again, still no luck with 3G.
vash265 said:
Yep...already did that and got it to boot just fine. Now I'm struggling with poor reception. I've seen other users (different phones) mention radio upgrades, but I was extremely unfamiliar with the terminology. The phone seems to work okay, but I only get 1x reception for data.
Or were you actually suggesting to repeat the entire process?
Edit - Tried again, still no luck with 3G.
Click to expand...
Click to collapse
Before doing what i stated did you wipe everything (system, data, cache, dalvik)? Also, you still getting a forceclose upon boot or just crap signal? And are you on sprint or electrify?
Acvice said:
Before doing what i stated did you wipe everything (system, data, cache, dalvik)? Also, you still getting a forceclose upon boot or just crap signal? And are you on sprint or electrify?
Click to expand...
Click to collapse
I wiped everything. I can boot into the OS and my phone works fine, but my data rate is stuck on 1x (so crap signal). I'm on sprint.
vash265 said:
I wiped everything. I can boot into the OS and my phone works fine, but my data rate is stuck on 1x (so crap signal). I'm on sprint.
Click to expand...
Click to collapse
well did you have 3g on stock? there's no reason it would go to 1x unless 3g is unavailable. the rom shouldn't cause it to go into 1x.
na7q said:
well did you have 3g on stock? there's no reason it would go to 1x unless 3g is unavailable. the rom shouldn't cause it to go into 1x.
Click to expand...
Click to collapse
Yep. Despite popular belief, I'm not a moron =) I'm in the dead center of 3G availability for Sprint in my area, and with stock android I get perfect 3G reception. I've read reports of the same things happening to other people, but haven't found a solution yet. I restored to stock after making a backup to try updating the PRL. I'll update again when I find out if it worked or not.
Edit - Sprint just sucks, apparently. http://www.sprintusers.com/forum/showthread.php?t=225908
When I rebooted to stock I checked the radio status and sure enough, 1xRTT. Evidently I am a moron =p
There was something wrong with the phone afterall. To fix it, I did the following:
Dial *#*#4636#*#*
You'll be presented with a menu. Go to Phone Information.
About halfway down the page, there will be a menu with a dropdown. Mine was set to CDMA. To fix the issue, I changed it to CDMA auto (PRL). I'm now receiving excellent 3G reception.
Hellybean is by far the best ROM I've used yet on my Note. It runs almost perfectly. I did have to reboot because my bluetooth wouldn't come on (reboot always fixes that). However, when I rebooted it, the phone tried to restart, I saw the Samsung SGH-I717 screen, and then it went black. It never brings up the Hellybean ring of fire. If I pull the battery I see the ring of fire for about 5 seconds, then it reboots, then black screen.
At this point, the only thing I can do is force the phone into TWRP and restore a previous backup. Does anyone have any idea what could cause the phone to not want to reboot back into the system?
I was on the latest Hellybean build and TWRP is up-to-date as well. I had to revert back to the October 10 build though. I just tried rebooting it after a restore and the same thing happens (so it's not specific to a certain date of ROM). As long as I don't reboot I don't have a problem.
Thanks
Chris
MI_SS_IL said:
Hellybean is by far the best ROM I've used yet on my Note. It runs almost perfectly. I did have to reboot because my bluetooth wouldn't come on (reboot always fixes that). However, when I rebooted it, the phone tried to restart, I saw the Samsung SGH-I717 screen, and then it went black. It never brings up the Hellybean ring of fire. If I pull the battery I see the ring of fire for about 5 seconds, then it reboots, then black screen.
At this point, the only thing I can do is force the phone into TWRP and restore a previous backup. Does anyone have any idea what could cause the phone to not want to reboot back into the system?
I was on the latest Hellybean build and TWRP is up-to-date as well. I had to revert back to the October 10 build though. I just tried rebooting it after a restore and the same thing happens (so it's not specific to a certain date of ROM). As long as I don't reboot I don't have a problem.
Thanks
Chris
Click to expand...
Click to collapse
have you tried any other roms?
I have ran every update of Hellybean since its arrival here. I had made a backup and flashed another rom, didn't like so I went to install back up.
it would not install, just kept looping in the boot screen. had to fresh flash the rom. didn't matter which, just had to reflash. screen never went black though. you issue sounds more similar to a stuck power button, which is why I ask if you have had same problem with another rom.
I find it hard to believe this rom wont restore a back up. others have not chimed in with that specific issue. but you and I may just be 2 that have voiced the issue. wasn't that big of issue for me as I thought it more an oddity. my back up wouldn't install at all in 3 attempts, so again, whyi question your power button.
try another rom real quick if you can. don't have to like or want it, but this is a test right?
let us know what happens
captemo said:
have you tried any other roms?
I have ran every update of Hellybean since its arrival here. I had made a backup and flashed another rom, didn't like so I went to install back up.
it would not install, just kept looping in the boot screen. had to fresh flash the rom. didn't matter which, just had to reflash. screen never went black though. you issue sounds more similar to a stuck power button, which is why I ask if you have had same problem with another rom.
I find it hard to believe this rom wont restore a back up. others have not chimed in with that specific issue. but you and I may just be 2 that have voiced the issue. wasn't that big of issue for me as I thought it more an oddity. my back up wouldn't install at all in 3 attempts, so again, whyi question your power button.
try another rom real quick if you can. don't have to like or want it, but this is a test right?
let us know what happens
Click to expand...
Click to collapse
Let me clarify ... I'm not having a problem restoring or installing Hellybean or any other ROM. It's after I install or restore and the ROM is running fine (for days even) ... at some point I have to reboot for some reason and it's then that it won't boot back into the ROM. In other words I can't reboot my system because it never comes back to the ROM. I have to then boot to TWRP, restore something else and then that will boot to the ROM. If I reboot again after the ROM is up and running, I get the same thing, it won't boot back into the ROM, I have to restore again. That rules out a power button ... if it was stuck I would never get back in.
I've tried most of the ROMs out there, but since Hellybean I haven't tried any others (because this is the best one). You think there's any possibility dirty flashing all of the Hellybean builds over top of each other could cause it? Maybe I'll try installing the latest one from a full wipe.
Thanks
Chris
MI_SS_IL said:
Let me clarify ... I'm not having a problem restoring or installing Hellybean or any other ROM. It's after I install or restore and the ROM is running fine (for days even) ... at some point I have to reboot for some reason and it's then that it won't boot back into the ROM. In other words I can't reboot my system because it never comes back to the ROM. I have to then boot to TWRP, restore something else and then that will boot to the ROM. If I reboot again after the ROM is up and running, I get the same thing, it won't boot back into the ROM, I have to restore again. That rules out a power button ... if it was stuck I would never get back in.
I've tried most of the ROMs out there, but since Hellybean I haven't tried any others (because this is the best one). You think there's any possibility dirty flashing all of the Hellybean builds over top of each other could cause it? Maybe I'll try installing the latest one from a full wipe.
Thanks
Chris
Click to expand...
Click to collapse
I have dirty flashed every one. the only thing I try to do when gong dirty is to still give it that 10 settle time. no particular reason other than my OCD
Okay, thanks for the replies. I'll play around with it some more, maybe try a fresh install and see if that changes anything. I'll let you know if I figure it out.
Chris
I figured it out. Not Hellybean at all. It was TWRP. I reverted back to an early build and then reinstalled 2.6.3.0 and now it reboots fine.
Chris
I guess I can't edit the title to reflect the correct issue? Thread can be deleted if the moderators want. Hellybean is running strong ... it's the first ROM I get 0 random reboots.
Thanks for the help captemo and to the makers of Hellybean.
Chris
beanstalk
I got exactly same problem with beanstalk 4.3.
I tried reinstall recovery but no luck. Every time powering off or rebooting need a fully wipe and restore.
Do you think other or older recovery will work?
hotgly said:
I got exactly same problem with beanstalk 4.3.
I tried reinstall recovery but no luck. Every time powering off or rebooting need a fully wipe and restore.
Do you think other or older recovery will work?
Click to expand...
Click to collapse
Same issue. Any of the 4.3 ROMS.
MI_SS_IL said:
I figured it out. Not Hellybean at all. It was TWRP. I reverted back to an early build and then reinstalled 2.6.3.0 and now it reboots fine.
Chris
Click to expand...
Click to collapse
So did you:
1- restore a stable backup
2- boot to recovery and flash TWRP (which version?)
3- Boot back into recovery
3- wipe and flash HellyBean
Is this correct?
I don't know what happened. Or why it won't work.
When Safestrap was originally finished, I installed Hyperdrive without a problem. An update came, I downloaded and installed. It made it so I couldn't use HotSpot anymore. So, I figured it was the Rom, and I installed Jellybean Rom. I didn't like it. I tried to install the original Hyperdrive I had, and once its installed and reboots, the lights come on for one second and shut off. Downloaded the newest Hyperdrive, same issue.
The instructions say wait for 10 minutes. I did, and longer. (Range usually 20-40 minutes)
Last night I wanted to try again, (downloaded newest hyperdrive. I have sloooooow internet. Took 5 hours to finish). So, I tried installing today following the instructions, same issue. It installs and says everything is fine, reboot, safestrap pops up, loads normally through that, and the lights are on after like it starts with Stock, lights shut off, phone stops working.
When this happens, the phone does not respond to anything. Power does nothing. I waited 45 minutes the 3rd time trying to reboot after install. The phone will not turn on, respond, or anything unless I pop the battery out and put it back in. I can get back into Safestrap that way.
I really want to use Hyperdrive, but it just won't reboot for my phone.
I do have the Verizon i545 version, ME7, Safestrap, Rooted, and newest Hyperdrive Rom. Used the Safestrap Kernel, but the phone locks up.
I've tried default settings, different Rom settings, (2gb and 3gb), removing almost everything from install, adding what I want, adding what I like, etc. No combination of settings will let me phone boot into Hyperdrive.
Any thoughts?
Are you completely removing then re-creating the slot when trying all these flashes?
Are you flashing the ME7 kernel module.zip ?
I redo the rom slot each time and act like it's the first time.
And i can't install the module... Tried multiple times but it fails almost instantly through ss.
Sent from my SCH-I545 using xda app-developers app
Excessumcarcer said:
I redo the rom slot each time and act like it's the first time.
And i can't install the module... Tried multiple times but it fails almost instantly through ss.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Have you tried to re-download the module? Preferably on the computer then transfer to your ExtSDCard with the ROM.
So... The one I downloaded to my computer failed, but the one I did with my phone worked.
Still the same issue. Won't boot past the SS message.
Sent from my SCH-I545 using xda app-developers app
Excessumcarcer said:
So... The one I downloaded to my computer failed, but the one I did with my phone worked.
Still the same issue. Won't boot past the SS message.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
While you were trying to install did you notice if zip signature was checked if so uncheck when you install and uncheck when you install module other than that don't know what else to say. When i first started i found that to be my problem.
The zip signatures were not checked. : /
Sent from my SCH-I545 using xda app-developers app
And I've tried the older version Hyperdrive with the new ME7 Modules, still won't work. I can't understand because everything says it was successful and ready to go, but it just doesn't.
Also double checked my i545 version, it is still ME7 and not the new one. The new update is pushy and wants to be installed more aggressively than the ME7 did. Highly annoying...
Excessumcarcer said:
And I've tried the older version Hyperdrive with the new ME7 Modules, still won't work. I can't understand because everything says it was successful and ready to go, but it just doesn't.
Also double checked my i545 version, it is still ME7 and not the new one. The new update is pushy and wants to be installed more aggressively than the ME7 did. Highly annoying...
Click to expand...
Click to collapse
Get off 3.62 and go back to 3.6 if you can. use root uninstaller to get rid of the current SS and shut down normally. ( all in stock rom ) reboot to stock recovery and factory reset. put the 3.0 SS back on and install twrp through that and reboot fully. then you can go into SS and reboot to recovery and you should be good
EDIT: go back to 3.6 SS not 3.0 haha
EDIT 2: always wipe even after you just created the slot and flash the modules with HD10 and advanced wip the dalvik and the cache only. and chill for 10 and boot her up..... and make sure you didnt accdentally get the dreadful OTA!!!
!Led*Eyes! said:
Get off 3.62 and go back to 3.6 if you can. use root uninstaller to get rid of the current SS and shut down normally. ( all in stock rom ) reboot to stock recovery and factory reset. put the 3.0 SS back on and install twrp through that and reboot fully. then you can go into SS and reboot to recovery and you should be good
EDIT: go back to 3.6 SS not 3.0 haha
EDIT 2: always wipe even after you just created the slot and flash the modules with HD10 and advanced wip the dalvik and the cache only. and chill for 10 and boot her up..... and make sure you didnt accdentally get the dreadful OTA!!!
Click to expand...
Click to collapse
FINAL EDIT!!! always pick the safestrap kernel during the Aroma install
If I helped at all, shoot me a Thanks and happy flashing!!
!Led*Eyes! said:
FINAL EDIT!!! always pick the safestrap kernel during the Aroma install
If I helped at all, shoot me a Thanks and happy flashing!!
Click to expand...
Click to collapse
I promise you this makes no sense....and I think there was something wrong with the stock rom...only thing I can conclude. I did a factory reset and bricked my phone. I can't even get into Safestrap now...whatever the issue was with the custom rom is now the issue with the stock rom. So, i'm just going to wipe my phone and start over from scratch as that is the only available step. Ill let you know if it fixed the issue or not.
Excessumcarcer said:
I promise you this makes no sense....and I think there was something wrong with the stock rom...only thing I can conclude. I did a factory reset and bricked my phone. I can't even get into Safestrap now...whatever the issue was with the custom rom is now the issue with the stock rom. So, i'm just going to wipe my phone and start over from scratch as that is the only available step. Ill let you know if it fixed the issue or not.
Click to expand...
Click to collapse
Did you have 3.62? my buddy did and his phone wouldnt let him delete it! crazy. i dont like 3.62 but i was running HDrls10 like a champ. not a single issue. With the me7 base i want to say i didnt even flash the modules over it but i cant remember. but basically ( by what i wrote down) you were going to start from scratch anyway.. there is a better root out now anyway. use the dialer codes and get a REAL factory reset!! There are a lot of people that arent digging the 3.62..... it was causing bootloops for a while but there are def still some lingering issues i think.
!Led*Eyes! said:
Did you have 3.62? my buddy did and his phone wouldnt let him delete it! crazy. i dont like 3.62 but i was running HDrls10 like a champ. not a single issue. With the me7 base i want to say i didnt even flash the modules over it but i cant remember. but basically ( by what i wrote down) you were going to start from scratch anyway.. there is a better root out now anyway. use the dialer codes and get a REAL factory reset!! There are a lot of people that arent digging the 3.62..... it was causing bootloops for a while but there are def still some lingering issues i think.
Click to expand...
Click to collapse
Well...nothing has worked.
Update for everyone, I was using the older SS, 3.60.
I killed everything, put the original Verizon ME7 Rom on the phone, re-rooted, put 3.62 SS on, (Done like it), installed the HDrls10, Installed the module, (both successful), restarted, exact same thing. Right after Safestrap Enabled pops up, the phone goes dark and the battery needs to be removed and put back in for it to turn on again.
So, I tried something crazy and for whatever reason it worked as far as HD is concerned...but...I went outside of the instructions.
I have the HD rls9 Final. I installed it through SS, used the modded Kernel, (non SS), and restarted. It popped right up in about 45 seconds. (Wasnt working before I reset everything and started over)
I tried HD rls10 Final that way, and nothing.
I will be redownloading it tonight to make sure it isn't the download. (I have slow internet, itll take all night likely.) : /
If anyone is looking to actually uninstall SS (which you need to do to roll back a version) you need to use the commands hashcode has provided. Using Terminal Emulator on the stock side will accomplish that. Read up on hashcode's SS OP.
My phone will not accept HDrls 10....no matter what I try. It accepted HDrls9 without issue, minus the hotspot not working. But it will not accept HDrls10...
Im out of ideas...
EDIT: I downloaded the HDrls 10 rom from two locations, tried both, both failed this morning.
Excessumcarcer said:
My phone will not accept HDrls 10....no matter what I try. It accepted HDrls9 without issue, minus the hotspot not working. But it will not accept HDrls10...
Im out of ideas...
EDIT: I downloaded the HDrls 10 rom from two locations, tried both, both failed this morning.
Click to expand...
Click to collapse
All I can think of is somehow you are getting bad downloads. Have you checked the MD5s to match per the download sites listing?
lazer9 said:
All I can think of is somehow you are getting bad downloads. Have you checked the MD5s to match per the download sites listing?
Click to expand...
Click to collapse
I just double checked the MD5. It matches the download. How frustrating. Double checked the build, double checked the MD5, double checked install procedure, etc. It flat doesn't work on my phone, and there is no logical reason to it. I tried from a fresh build twice now, doing the rooting and SS install from stock everything.
It locks up right after SS, still.
Electronics hate me, it has been determined before. This is just further proof.
: /
So, I've done pretty much everything feasible. Guess Ill have to stick with an older HD or different rom. : (
Also, hotspot doesn't work HD 9 for me, (nor Jellybeans). I installed the module when I did the rom, but there is no hotspot for one. And two, when I download and use FoxFi, which I paid for to use on the Stock Rom before SS, it will try to turn it on and then it freezes and crashes.
All I want is a non-Verizon Rom with working Hotspot!!!! AHHHHH!!!! Looks like that aint happening.
Well played Verizon...well played. Perahps I should get an international phone and go to another company. Expensive, but tempting.
So, the final verdict for those following -
Hyperdrive 10 - Does not work on my i545 no matter what I tried.
Hyperdrive 9 - Works but the hotspot is glitched and froze no matter what I tried.
Jellybean - Works the same as HD 9
Synergy - Works. Everything on it works, hotspot, install, etc.
Not sure why the others did not work. But, for whatever reason Synergy works flawlessly for my i545. Installed and downloaded the same ways as the others, yet it worked.
: /
I was planning on trying a few others first, but Synergy claims to block Samsung from logging information from my phone. I realize this doesn't stop every company from doing it, but its the thought that counts. lol. So, Im trying this Rom out now. It's no hyperdrive, but it works.
After a BUNCH of tries I finally got it to work!!
I have a Verizon i545 with ME7. I basically started as if I'd never installed HD 9.1 in the first place.
Here's what I did.
1. Double check that your device is rooted. I used Root Checker Basic. I actually re-rooted my device just to be sure (I venture to guess it might have been unnecessary) and it worked.
2. I used a 4GB SD formatted to ex-fat and put the HD RLS10 AND the ME7 modules .zip file on it (Both on the SD)
3. I then booted into recovery.
4. Make a new ROM slot.
5. Name it whatever you like.
6. When you go to flash HD, hit the add zip button and select the ME7 modules.zip
7. When HD gets done flashing UNCHECK the "Reboot" box up top and then hit the reboot tab at the bottom right.
8. It will automatically flash the ME7 modules next. When it says 'Successful', then reboot.
9. Give it a few seconds and hopefully it will work for you as well. Good luck.
Latest installable version for Me7?
What is the latest installable version of HD for verizon locked Me7 bootloader, i currently have rls10.0 installed and ive tried 10.1, 10.2, and now 12 and none of them boot up.
Longtime XDA'er here with a problem.
I was rooted on stock 4.1.2 for over a year but wanted to update to take advantage of newer features such as chromecast mirror on kitkat. I had a perfectly working phone until I tried flashing updates. I followed instructions and only flashed the MJ9 baseband on roms that tell me too, and even flashed ND7 baseband for other ports. I was able to install multiple variants of 4.4.2 with both twrp and philz recoveries with the same result. I can't get sms/mms to come in. What's weird is upon bootup I will get the same test message only once, then nothing. I even tried flashing agni kernel with no luck. The phone works great with the exception of text messaging. Calls work, GPS locks, and no issues with wifi. APN settings look fine (compared to my wife's note 2 which is identical model still on 4.1.2). I popped my sim into an LG lucid I had as a backup and the text's sitting in limbo start streaming in, so I know my sim isn't bad. I even made sure to disable hangouts with no luck. Even tried Go Sms Pro with same result. I have since decided to go to 4.3 and am having the same issue on those roms on the MJ9 baseband and MJ9 stock kernel.
I'm pulling my hair out because I can't figure this out and I'm a pretty smart fella, this just has me stumped.
Ideas anyone? I have been researching like mad and nothing I try seems to resolve.
Thanks in advance!
timber03 said:
Longtime XDA'er here with a problem.
I was rooted on stock 4.1.2 for over a year but wanted to update to take advantage of newer features such as chromecast mirror on kitkat. I had a perfectly working phone until I tried flashing updates. I followed instructions and only flashed the MJ9 baseband on roms that tell me too, and even flashed ND7 baseband for other ports. I was able to install multiple variants of 4.4.2 with both twrp and philz recoveries with the same result. I can't get sms/mms to come in. What's weird is upon bootup I will get the same test message only once, then nothing. I even tried flashing agni kernel with no luck. The phone works great with the exception of text messaging. Calls work, GPS locks, and no issues with wifi. APN settings look fine (compared to my wife's note 2 which is identical model still on 4.1.2). I popped my sim into an LG lucid I had as a backup and the text's sitting in limbo start streaming in, so I know my sim isn't bad. I even made sure to disable hangouts with no luck. Even tried Go Sms Pro with same result. I have since decided to go to 4.3 and am having the same issue on those roms on the MJ9 baseband and MJ9 stock kernel.
I'm pulling my hair out because I can't figure this out and I'm a pretty smart fella, this just has me stumped.
Ideas anyone? I have been researching like mad and nothing I try seems to resolve.
Thanks in advance!
Click to expand...
Click to collapse
Odin back to stock should fix this issue.
DreamFX said:
Odin back to stock should fix this issue.
Click to expand...
Click to collapse
flashing stock 4.1.2 via Odin does fix it, but when I try to upgrade to any rom from there I have same problem. Pretty much all of the roms 4.3+ specify flashing with MJ9 firmware, which I have done. I have tried 4 roms today and same problem every time.
So annoying, it's like I can't get higher than 4.1.2
timber03 said:
flashing stock 4.1.2 via Odin does fix it, but when I try to upgrade to any rom from there I have same problem. Pretty much all of the roms 4.3+ specify flashing with MJ9 firmware, which I have done. I have tried 4 roms today and same problem every time.
So annoying, it's like I can't get higher than 4.1.2
Click to expand...
Click to collapse
I'm really surprised I'm the only one having this issue. After much research and countless attempts, it seems the most I can do is run stock 4.1.2 rooted, and can apply the MJ9 firmware... but if I try to update to any rom 4.3 or above, my text messaging stops working, otherwise the ROM's work great and phone calls, 4G Data, Wifi, GPS, etc all work perfect... only the sms/mms doesn't.
If I run the stock, rooted 4.1.2, with MJ9 radio everything runs great, including sms/mms, so my feeling is that I need a rom that doesn't flash kernel, or baseband, but jsut system, data, etc... then I might have a shot but it's a long shot at this point. I have even tried beans build 26 which is 4.3 and have EXACTLY the same problem.
The only other thing I've noticed is I have hardware version I605.07 whereas most people it seems have I605.06 from what I've noticed while browsing similar threads.
got it working with no help from anyone... a lot of steps but worth it. Definitely not the normal path everyone has been posting.
timber03 said:
got it working with no help from anyone... a lot of steps but worth it. Definitely not the normal path everyone has been posting.
Click to expand...
Click to collapse
Timber any chance you would be ale to point me to the fix? This has been driving me nuts
sugarfunk said:
Timber any chance you would be ale to point me to the fix? This has been driving me nuts
Click to expand...
Click to collapse
Absolutely... I will type up instructions in the morning. As for driving you nuts I know exactly what you mean... I was pulling my hair out and almost gave up hope but I tried something and it worked. It involves using beans 26 rom and a combination of Twrp and Philz recoveries and backup/restores... if you are having this problem, the main problem is the flashing of the MJ9 firmware.
I'll clue you in tomorrow
sugarfunk said:
Timber any chance you would be ale to point me to the fix? This has been driving me nuts
Click to expand...
Click to collapse
as promised, here's the steps it took for me to get working... It may seem a little bit of a long process but almost 4 days now and no more issues, so I trust this process. It must be something different in my hardware versus other, and I'm assuming yours is like mine.
Let me know if you have any questions
Start with 4.1.2 stock rooted
1. Install latest TWRP Recovery v2.7
2. Backup EFS and Modem as separate backups to your external SD card
3. In Recovery, Wipe.. Advanced Wipe and wipe everything (including Internal Storage) except external SD and USB-TG partitions
The next set of steps is to ensure you have a clean base to work with...
4. Reboot to download mode and using Odin 3.07 flash stock 4.1.2 firmware
in Pit select Sch-i605-16gb.pit
in PDA, select the stock 4.1.2 MC3 firmware
make sure only the following checkboxes are selected: "Auto Reboot", "Re-Partition" and "F. Reset Time"
Hit Start, wait till process completes and boots into o/s. Then skip all wizard options to get to home screen.
5. Root phone using casual
I had no issues using version "NoYouVerizon-GalaxyNote2-CASUAL R515.jar"
6. After root is successful, boot to Recovery and install latest TWRP recovery again since you will have twrp v2.5 due to the root process
7. Repeat step #3 (3 times to make sure everything is wiped clean)
8. IMPORTANT as this is what seemingly fixed the sms issue for me: using twrp recovery, restore the EFS backup you took in step #2 (do not restore the modem)
9. Install Beans 26 rom (Alliance 4.3) which will now give you a proper MJ9 base and kernel to work with. Again, skip all wizard prompts after it loads just so you can get to home screen.
10. Boot into recovery and now backup the new 4.3 EFS and modem partitions to your external SD.
You are not actually going to need the modem backup for the next steps, but if you have a problem installing a rom,
you now have working MJ9 EFS and Modem partitions should you have a problem with any roms from this point forward
11. Repeat step 7 & 8 (restore only the EFS 4.3 partition)
12. Important.. Now install latest Philz recovery
13. Install 4.4.2 rom using Philz recovery
At step 13 is where I installed the Ditto Note 3 rom v5.2, and chose "do not wipe" during the aroma install process.
14. once installed allow it to reboot, if it hangs on samsung boot animation for more than 5 minutes do the following:
a) pull battery and boot into philz recovery, then wipe only the following: Data, Cache, and dalvik cache
b)Install Agni Kernel (PSN_AGNi_pureSTOCK-v4.2.5_I605_4.4.2_AROMA-signed.zip)
c)reboot and you should get the android wizard for the rom in 2 or 3 minutes
If you have a problem like I did with regards to the Camera not working in the new rom, dirty flash the rom again (do not do any wiping)
Then re-install Agni Kernel since the rom installs it's own, otherwise it will break wifi, at least it did on mine.
There are a few more fixes to get tethering, etc working but I can provide those steps if needed. It basically involves installing xposed framework and the moto-x module.
timber03 said:
as promised, here's the steps it took for me to get working... It may seem a little bit of a long process but almost 4 days now and no more issues, so I trust this process. It must be something different in my hardware versus other, and I'm assuming yours is like mine.
Let me know if you have any questions
Start with 4.1.2 stock rooted
1. Install latest TWRP Recovery v2.7
2. Backup EFS and Modem as separate backups to your external SD card
3. In Recovery, Wipe.. Advanced Wipe and wipe everything (including Internal Storage) except external SD and USB-TG partitions
The next set of steps is to ensure you have a clean base to work with...
4. Reboot to download mode and using Odin 3.07 flash stock 4.1.2 firmware
in Pit select Sch-i605-16gb.pit
in PDA, select the stock 4.1.2 MC3 firmware
make sure only the following checkboxes are selected: "Auto Reboot", "Re-Partition" and "F. Reset Time"
Hit Start, wait till process completes and boots into o/s. Then skip all wizard options to get to home screen.
5. Root phone using casual
I had no issues using version "NoYouVerizon-GalaxyNote2-CASUAL R515.jar"
6. After root is successful, boot to Recovery and install latest TWRP recovery again since you will have twrp v2.5 due to the root process
7. Repeat step #3 (3 times to make sure everything is wiped clean)
8. IMPORTANT as this is what seemingly fixed the sms issue for me: using twrp recovery, restore the EFS backup you took in step #2 (do not restore the modem)
9. Install Beans 26 rom (Alliance 4.3) which will now give you a proper MJ9 base and kernel to work with. Again, skip all wizard prompts after it loads just so you can get to home screen.
10. Boot into recovery and now backup the new 4.3 EFS and modem partitions to your external SD.
You are not actually going to need the modem backup for the next steps, but if you have a problem installing a rom,
you now have working MJ9 EFS and Modem partitions should you have a problem with any roms from this point forward
11. Repeat step 7 & 8 (restore only the EFS 4.3 partition)
12. Important.. Now install latest Philz recovery
13. Install 4.4.2 rom using Philz recovery
At step 13 is where I installed the Ditto Note 3 rom v5.2, and chose "do not wipe" during the aroma install process.
14. once installed allow it to reboot, if it hangs on samsung boot animation for more than 5 minutes do the following:
a) pull battery and boot into philz recovery, then wipe only the following: Data, Cache, and dalvik cache
b)Install Agni Kernel (PSN_AGNi_pureSTOCK-v4.2.5_I605_4.4.2_AROMA-signed.zip)
c)reboot and you should get the android wizard for the rom in 2 or 3 minutes
If you have a problem like I did with regards to the Camera not working in the new rom, dirty flash the rom again (do not do any wiping)
Then re-install Agni Kernel since the rom installs it's own, otherwise it will break wifi, at least it did on mine.
There are a few more fixes to get tethering, etc working but I can provide those steps if needed. It basically involves installing xposed framework and the moto-x module.
Click to expand...
Click to collapse
Whatever works for you. Glad your back up and running.
I have just recently tried to install the official cm11 images for my g3. They worked fine. Then, when I installed gel x-posed settings and activated it, I would get said error. It would pop up again and again. This would lead me to reflash my ROM. Then, I do not know what happened, when I would flash a ROM, I would get the error from the start. I eventually fixed this error. But then, when I tried to upgrade the nightly, I got the error again. So I flashed the ROM again, and let it sit. After a little while of perfection, the error came back up!
Here's what I have tried:
-reflashing the boot.IMG (unzipped)
-clearing cache (recovery)
-clearing Sim tool cache/data (said they were non existent when trying)
-reflashing stock, then reflashing cm11
I really want cm11 on my g3, but with these issues, I don't know whether I can now.
Any help would be appreciated!
Sent from my Nexus 7 using XDA Free mobile app
CM Nightlies are working perfect for me with no errors. Here is the process I went through:
I am still using TWRP 2.8.0 which is the version I installed when I originally Bumped! my phone.
I downloaded CM and Gapps to root of my internal SD storage
I chose to Wipe in TWRP
I chose Advance Wipe
I picked every option except for Internal Storage and External SD Card/Storage
I then Wiped
Out of habit, I do this 3 times (don't ask why, I just do it from when I had older android devices)
I then go back to wipe main screen and slide to do the standard wipe, 3 times
Yes, this is probably overkill!
I then go to install in TWRP
I install CM, then I install gapps (using the gapps that are on this list: https://itvends.com/gapps/
Yes, the date of those gapps are a little older, but that is what worked for me per OP'S instructions
I went through setup of my phone, fixing APN, Setting WIFI to USA, signing into Google after first loading into Rom instead of signing into Google on first bootup. Did a reboot
Installed Xposed, and the modules needed, reboot
I never received any error
I have done 3 nightly updates so far, as of 11/30. I am sure 12/1 will be ready in an hour or so.
I always click on about phone, download said update and let the process do its thing automatically, walk away and the phone is ready to use
Still no errors whatsoever. In fact, this has been the first version of AOSP I have used for the G3 with 0 errors. It is perfect, for me - No issues.
Hope that helps.
mwest316 said:
CM Nightlies are working perfect for me with no errors. Here is the process I went through:
I am still using TWRP 2.8.0 which is the version I installed when I originally Bumped! my phone.
I downloaded CM and Gapps to root of my internal SD storage
I chose to Wipe in TWRP
I chose Advance Wipe
I picked every option except for Internal Storage and External SD Card/Storage
I then Wiped
Out of habit, I do this 3 times (don't ask why, I just do it from when I had older android devices)
I then go back to wipe main screen and slide to do the standard wipe, 3 times
Yes, this is probably overkill!
I then go to install in TWRP
I install CM, then I install gapps (using the gapps that are on this list:
Yes, the date of those gapps are a little older, but that is what worked for me per OP'S instructions
I went through setup of my phone, fixing APN, Setting WIFI to USA, signing into Google after first loading into Rom instead of signing into Google on first bootup. Did a reboot
Installed Xposed, and the modules needed, reboot
I never received any error
I have done 3 nightly updates so far, as of 11/30. I am sure 12/1 will be ready in an hour or so.
I always click on about phone, download said update and let the process do its thing automatically, walk away and the phone is ready to use
Still no errors whatsoever. In fact, this has been the first version of AOSP I have used for the G3 with 0 errors. It is perfect, for me - No issues.
Hope that helps.
Click to expand...
Click to collapse
I did everything exactly as you did, including the 3 wipes, also out of habit. I too however, get the same error with the latest nightly. It starts popping up as I try to add my Gmail account at the initial setup. Previously, the 'unofficial' builds did not do this to me. This is the only rom that does this, I have tried them all out. I have yet to try to flash a different gapps package to see if that makes a difference. Apparently I dont get the data issues with cm12, but get phone issues with cm11.
I'm a bit relieved to see I'm not the only one having this problem. Been updating every night to see if maybe it's fixed, but I still get the same error. Didn't happen on the first nightly I flashed, though. It lol seems to be happening at random for me. Sometimes I'll set my phone down for a couple hours, working perfectly fine. Then I pick it up to check something and I suddenly start getting that error. I've tried every "solution" I find and none of them work for me. Even thought it was an issue with reading my sim card because when I get the error, it shows that my sim card isn't being read. But I still get it when I take it out. A normal factory reset doesn't fix it either. I have to do a complete data format to remove the error.
I found a quick little fix where i make a backup earlier in the day and just restore it whenever I start getting the error, but it's still very annoying.
Same issue
Hey bros,
Same thing here. It's a baseband radio issue. Notice in settings under About Phone it says 'Baseband Version: Unknown'. Either TWRP is flashing over our baseband (not likely, calls and texts can be made before the error message attacks come), or CM11 has some issue on certain builds with reading our SIM cards. I think having an official 10B or 11C flashable baseband radio to install at the time of the ROM install will fix this problem. Waiting on CM to patch the code will take too long. Let me know if you find one of these basebands or can find out how to extract it (from file manager or somewhere?) as I have not been able to find this info on XDA or anywhere.
EDIT: I FIXED IT
I'm a new member, and XDA won't allow me to post links..... look in the OP for JasmineROM (all credit to author for posting this 11C modem and fabulous stock LG debloated ROM) under downloads, you'll find the 11C modem. Download it.
1. Place 11C modem.zip on external or internal, whichever you want. I prefer external.
In TWRP:
2. Backup, unless youre livin' life on the edge.
3. Wipe it all except for external (or internal, if you prefer to flash from your internal storage)
4. Add to Install zip que in order:
a) latest CM11 nightly
b) 11C modem found in JasmineROM OP of main thread
c) GAPPs of your choice (I like nano PA GAPPs, and just install whatever else i want after)
5. FLASH
6. profit
7. PHAP
I have heard the 10B radio works great too. holler back and post results between the 2 stock radios for VS985.
Please hit thanks, as I am new and want to be helpful, where possible. Please share this so others know that we can overcome this nonsense.
CM11!!! Phappin' so hard right now!
Got it again.... totally blowed right now. maybe reconfig APN to match VZW and it will work?
Thanks for all the responses, it currently seems that the problem is cm11. I will probably wait for a stable build. For now, I'm using an unofficial cm12 ROM. Thanks for all the help!
Sent from my LG-VS985 using XDA Free mobile app
8pscott said:
Thanks for all the responses, it currently seems that the problem is cm11. I will probably wait for a stable build. For now, I'm using an unofficial cm12 ROM. Thanks for all the help!
Sent from my LG-VS985 using XDA Free mobile app
Click to expand...
Click to collapse
Are you using that PA GAPPs package that's in alpha? I think i'm going to give up and go to 12 too... I do know that the first official nightly of CM11 doesn't give me any errors, but Trebuchet is so buggy it won't take widgets. Had to download Nova
It makes me cry. My phone lasted through the night. Woke up at around 7 and it was fine. Went back to sleep and woke up at around 8:30 and I was crushed to see the problem happening again. There doesn't seem to actually be anything thy triggers it. :/
Yeah I think I'm gonna just try out cm12 and see how that goes.
Double check to make sure the phone isn't running in art. That fixed my problems! Xposed and art do not work together!![emoji2]
Im getting the same error on my phone usually a few says after using any of the nightlies. When i go to make a phone call it gives me the force close and doesnt stop. Ive since moved back to stock hoping someone had more info on the issue. My phone was not using Art but I did have xposed installed.