[Q] HTC ONE Stuck On Rom Installation Screen - T-Mobile HTC One (M7)

At first I tried flashing the ElementalX kernel and my screen didn't turn on. So I waited a day and the htc logo finally showed up and I immediately went into recovery. I already had the Renovate Rom before so I tried installing it as I did a while back. I made a noobie mistake by not realizing that my battery life was at 13 percent. So I tried installing the rom. And its stuck where it says "System Unmounted Already" At the bottom it says its at 20 percent and its installing the rom. However, its already been 2 hours since its been at 20 percent. I currently have the htc one charging but I presume that it wont be solved by just charging it considering that the red light isn't on. Please help me find a solution. To make matters worse I only have a mac laptop.

Alexrt890 said:
At first I tried flashing the ElementalX kernel and my screen didn't turn on. So I waited a day and the htc logo finally showed up and I immediately went into recovery. I already had the Renovate Rom before so I tried installing it as I did a while back. I made a noobie mistake by not realizing that my battery life was at 13 percent. So I tried installing the rom. And its stuck where it says "System Unmounted Already" At the bottom it says its at 20 percent and its installing the rom. However, its already been 2 hours since its been at 20 percent. I currently have the htc one charging but I presume that it wont be solved by just charging it considering that the red light isn't on. Please help me find a solution. To make matters worse I only have a mac laptop.
Click to expand...
Click to collapse
Help would highly be appreciated.

Alexrt890 said:
At first I tried flashing the ElementalX kernel and my screen didn't turn on. So I waited a day and the htc logo finally showed up and I immediately went into recovery. I already had the Renovate Rom before so I tried installing it as I did a while back. I made a noobie mistake by not realizing that my battery life was at 13 percent. So I tried installing the rom. And its stuck where it says "System Unmounted Already" At the bottom it says its at 20 percent and its installing the rom. However, its already been 2 hours since its been at 20 percent. I currently have the htc one charging but I presume that it wont be solved by just charging it considering that the red light isn't on. Please help me find a solution. To make matters worse I only have a mac laptop.
Click to expand...
Click to collapse
I had a flash go bad and get stuck on mine, I just rebooted it into Recovery (power & vol down), did a full wipe, including cache & dalvik cache, and ran the flash again, it worked. Are you not able to get back into recovery?

trjlive said:
I had a flash go bad and get stuck on mine, I just rebooted it into Recovery (power & vol down), did a full wipe, including cache & dalvik cache, and ran the flash again, it worked. Are you not able to get back into recovery?
Click to expand...
Click to collapse
I fixed it. At first I wasn't able to get back into recovery since the phone was turned off and didn't turn on. However, I let the phone stay still for about a day and let the battery die. I than charged it and put it back into recovery as soon as I saw the htc logo.

Related

Woke up & phone dead ?

All,
I have been on here for months, but this my 1st post. I have an Atrix that has been rooted, boot loader unlocked, Tenfar's recovery, but running stock ROM 1.8.x. I have not done any "tampering" with or ROM updates or anything like that. The phone in a few weeks and it has been working flawlessly.
However, this morning when I woke up, the phone is just sitting there dead. My wife said she heard a weird beep a few hours earlier. It will not power up via battery and the power button does not appear to work either.
I attached it to the wall charger an it will come up to the motorola and display "unlocked" but will not go past that screen. I also noticed that no charge led is lit up at all ... Strange ? I was able to get into recovery and I tried for a restore using Tenfar's CWM but after it completed and I went for a "reboot phone now" it just went back to the black screen and never booted at all.
Any thoughts ? Thanks in advance !
-Nathan
nathanmurray said:
All,
I have been on here for months, but this my 1st post. I have an Atrix that has been rooted, boot loader unlocked, Tenfar's recovery, but running stock ROM 1.8.x. I have not done any "tampering" with or ROM updates or anything like that. The phone in a few weeks and it has been working flawlessly.
However, this morning when I woke up, the phone is just sitting there dead. My wife said she heard a weird beep a few hours earlier. It will not power up via battery and the power button does not appear to work either.
I attached it to the wall charger an it will come up to the motorola and display "unlocked" but will not go past that screen. I also noticed that no charge led is lit up at all ... Strange ? I was able to get into recovery and I tried for a restore using Tenfar's CWM but after it completed and I went for a "reboot phone now" it just went back to the black screen and never booted at all.
Any thoughts ? Thanks in advance !
-Nathan
Click to expand...
Click to collapse
Could be simply that your battery is dead. If you have a friend with an Atrix the first thing to try is an alternative battery.
If that doesn't help the second thing to try would be a full rom flash and full wipe via fastboot.
This happened to me as well. The phone will not charge during boot so what I did was enter fastboot with hardware(or an option like that) and I got past it started up in a couple minutes.
Hw bypass with bp**
Sent from my MB860 using XDA App
reply
It appears to be the battery ... I tried it with a different one and it booted without issue. Very strange as it appears to have died all of the sudden. Just glad it is not the actual phone. Anyway, thanks for the info, much appreciated !

Bricked?

My phone was running at about 60% battery last night, and working fine. It was in my pocket and it vibrated. I was unable to turn it on or reboot it, even after removing the battery. I tried using the battery from my wife's S2 but still no luck. I tried connecting the power supply but it still wouldn't boot so I left it charging overnight.
This morning it alternately flashed a fully green battery and a fully black battery. If I press and hold the power button it starts the boot process - I get past the Samsung splash screen and see the first "Resurrection Remix" splash screen, but then it reverts to displaying the green battery.
Any ideas for how I can revive the phone??
itm said:
My phone was running at about 60% battery last night, and working fine. It was in my pocket and it vibrated. I was unable to turn it on or reboot it, even after removing the battery. I tried using the battery from my wife's S2 but still no luck. I tried connecting the power supply but it still wouldn't boot so I left it charging overnight.
This morning it alternately flashed a fully green battery and a fully black battery. If I press and hold the power button it starts the boot process - I get past the Samsung splash screen and see the first "Resurrection Remix" splash screen, but then it reverts to displaying the green battery.
Any ideas for how I can revive the phone??
Click to expand...
Click to collapse
Ok We cant say its bricked!! Because its booting up but not coming to homescreen rite? Are u able to get into recovery or download mode?? If ur able o then wipe the data cache and dalvik cache, reinstall the ROM again.. If Recovery doesnt shw up.. Then Use ODIN to flash original fw!! Even if u still couldn get it.. Order a USB JIG from Ebay and try getting into DOWNLOAD MODE!! Even after this its still working means ITS BRICKED !!
Start download mode and the flash a new stock firmware . And your phone isnt bricked .!
This is why I always make a backup.
If you can get into download mode you can fix it, if you can't it's a service centre job. Pretty simple really.
Try cleaning charging port..
Sent from my GT-I9100 using XDA
Uh oh...I managed to get into Recovery mode, did a factory reset and kicked off a re-install of the Resurrection Remix ROM from the external SD and it's hung at 50% (for 10 mins now) - at the "Extracting /system..." stage. I daren't interrupt it.
Any ideas???
Yes stop messing
1: If you dint have to save anything, wipe better to full wipe
Flash a stock Rom using Odin, than start again with custom roms.
OR
2: download your custom Rom again and flash, might be corrupt download.
atifsh said:
Yes stop messing
1: If you dint have to save anything, wipe better to full wipe
Flash a stock Rom using Odin, than start again with custom roms.
OR
2: download your custom Rom again and flash, might be corrupt download.
Click to expand...
Click to collapse
So it's OK to interrupt this ROM flash, even though it's stuck at 50%? Should I just hold the power button or remove the battery??
pull the battery
But I say flash stock Rom first, lengthy procedure I know, but safer
OK I decided to reflash RR 2.3, which had been running fine for a couple of weeks previously. Immediately after flashing (which worked OK) the boot process wouldn't complete - it got as far as the RR splash screen then died (screen blank, and needed a long press on the power button to restart).
This happened several times. Eventually I removed and replaced the battery and it finally booted.
Does this sound like a hardware problem? I've noticed that the phone often runs quite warm, but I don't know if that's normal.
You have to flash stock rom, only way to know if there is something wrong with your phone, run it for couple days.
Now to the heat issue, it is due to
1: modem
2: kernel
3: both

[Q] 5.0, Mostly Boot Loop with Battery Icon

Device: Galaxy Player 5.0 INTL (YP-G70)
ROM: Cyanogenmod 10.1 (7/23/2013)
Kernel: Sultan r5 INTL
Problem: The battery appears to be malfunctioning somehow. After using "Pimp My Rom" and enabling some tweaks, the device began to randomly turn off and loop on and off with a white battery outline onscreen. Now, the battery has sufficient charge. When it finally turns on, it's always over seventy percent. When it does turn on, if it is plugged in on the wall charger, it immediately turns off upon disconnecting this wall charger. Also, it displays "Android is upgrading, starting apps" at every boot. Managing to turn on the device after doing a reboot with the power button many times takes up to 15 minutes. It sucks. ):
Steps attempted:
Reflashing ROM and kernel using exact steps (wiping all data, /system, cache, etc.).
Flashing Cyanogenmod 10.2 (8/05/2013) with Sultan r6.
Deleting battery stats.
Cleaning charger and microUSB port.
Rechanging tweaks to the values I remember in Pimp My Rom. (IDK about all of them, if someone could post the defaults that would be great).
Draining battery (I did to 1%) and then recharging. Should I drain until it turns off?
[EDIT]: Tried flashing to Chip v1.5 with r14 kernel. No luck; it is just a different battery icon.
[EDIT]: Tried flashing to stock with Odin.
Are there any steps that I could possibly take to fix this? Perhaps flash to stock and see if the problem persists?
[WORKAROUND!] I've found a workaround, however annoying it may be. Plug in the YP-G70 and it should bootloop with the battery icon. However, as the icon disappears and the screen is black for about a second, just before it is about to reboot with the icon, pull the charger from the device. This has guaranteed my device to start every time; I can't ensure that it will work for you, but it is worth a try.
Please help!
You need to either do a factory reset from within the settings or wiping factory reset from within CWM. If that doesn't work you may need to flash back to stock.
Sent from my YP-G1 using xda app-developers app
obscuresword said:
You need to either do a factory reset from within the settings or wiping factory reset from within CWM. If that doesn't work you may need to flash back to stock.
Click to expand...
Click to collapse
I have done many factory resets from CWM. Would flashing back to stock do anything that flashing another rom wouldn't?
Also, after scouring xda for answers, I saw iurnait recommended draining the battery until the device turns off. I'm going to try that I suppose.
I'd flash back to stock if that doesn't work
Sent from my YP-G1 using xda app-developers app
Unfortunately, flashing to stock using Odin didn't remove the problem.
I used a guide from androidromupdate
To be honest, I've given up. I'll update the original post with what I've tried and the workaround that I've found for this dreadful issue. If anyone else has this issue, best of luck!
I've got the same "boot loop with battery logo" problem, but without the random shutdowns are "android is upgrading" message on boot.
Some additional details:
I can boot into download mode without any trouble.
It will occasionally complete a boot, but gets stuck in the loop as soon as something causes it to reboot or shutdown.
I can sometimes boot into recovery mode. It will successfully go into recovery mode about 2-3 times before it will go into a normal boot.
Flashing alternate kernels (even going all the way back to stock) just changes the battery logo, but does not stop the bootlooping problem
The stock kernel was far more reliable than the others, often booting all the way after only 3 or 4 tries.
Throughout the boot loop, the battery logo (except in the stock kernel) will show as empty, even after being charged overnight
Upon a successful boot (all the way to android home screen), the battery is shown as fully charged (if it's been charging) or a level that seems probable (e.g. it'll show as 70-80% if it's been in download mode (which keeps screen on at full brightness) for a while or left to bootloop for close to an hour.
If it's not plugged into a charger, it only loops once each time you turn it on (i.e. battery logo shows for a few seconds then the device shuts itself off).
An update to Joseph's posted workaround:
I've found the button lights a perfect indicator for the timing. Wait for them to go black and then come back on very dimly then unplug the cable before the screen shows anything or the key lights go full brightness (like they are when device is fully booted and awake).

[Q] Boot Loop after full discharge

Hello.
I have a i9100 smartphone with stock XWLSW firmware. After last change of firmware I did not even root it. So it was all stock without root.
My battery was already in bad condition - from 9 AM till 2-4 PM it gets to 15%.
But anyway.
Yesterday it discharged to 1%, when I plugged charger into the phone. I left it working, and after a while I tried to turn the screen on, but the phone was not responding to power key. It was not turning on the screen, and long hold did not turn the phone on.
I unplugged the charger, took out battery and saw a small wet spot on sticker and on battery (maybe it leaked a bit).
Well, it was not the first priority at the moment, so I just wiped it, and put the battery back, then I turned the phone back ON.
It started, but now I have a boot loop at Samsung Logo. When the battery was still discharged I could hear the discharge signal after logo, and then the logo starts again, and discharge signal again, etc.
I left it in that state for a night with charger plugged in. In the morning - it was in the same condition.
Things I tried:
Removing battery for over 10 minutes, clearing Cache from recovery.
Both recovery and download modes are working.
So the question is - can I restore the phone without Factory reset?
If not - can I somehow backup my data (savegames, etc) before doing factory reset?
I just tried to update the firmware again using ODIN with no luck. It updated successfully, but than again hangs on Samsung Logo.
Rule 1: Don't complain until you haven't tried factory reset.So be a man,and do a full wipe.
^^^^
What he said. Also, flash a 3 part firmware, which will also wipe your phone & has a funny habit of fixing situations like this.
I was going to do a Factory Reset or flash 3 part firmware, but only after I backup data. That was my main point of creating this thread - how to backup data in this situation.
Anyway, I did install Philz kernel, wiped dalvik cache, cache partition - it helped, but not for long. I saw my desktop, but after few seconds it went into boot loop again. I then did a Custom backup of data only, and did a Factory Reset through recovery.
Now I try to restore data to see what it will give me.
So i have been having pretty much the same problem with some little differences.
First my battery seems OK, no leaking no nothing, but it might just got old as I've got the phone for over 2 years now... Second, my bootloop occurs after full discharge, when i try to turn on the phone afterwards it just gets stuck on Galaxy SII logo, not even the boot, and stays that way no matter how long i wait. Third, at about the last 5-8% my screen starts flickering as if it wasn't getting enough electricity which shouldnt happen too and never happend before 4 months or so.
So lastly I've been getting this bootloop every now and then. Ive got a temporary fix by backing up my phone through recovery then wiping it clean and then restoring. But i just cant figure out why it does that.... I mean wipe helps, but i do restore everything afterwards....
Without restoring the problem still occurs so its not like i restore something deffective in the sw that makes this happen...

Help with HTC amazed, display has no lights but the phone is on.

Hello, I have an HTC Amaze for over a year now. It was working fine, I rooted it CWM 5. and I installed Android revolution custom ROM. Until 2 weeks ago my battery was giving me some trouble, so i put away the phone for a bit, I bought a new battery then I notice the phone wasn't coming on. SO i charge for an entire day it still wasn't charging. I carried it to the shop. They said, that they don't know whats wrong with the phone.
I came home and decide am going to fix it my self i tried powering it into recovery mode, hard reset. screen is still blank, at lease that is what I thought. I look closely and then i notice the phone was in recovery mode but no lights were on in the screen. So normally I thought what anyone would of thought, the bulb in the screen or some kind of wiring went bad. The i tried wiping cache davlik install new new rom. Nothing worked. and this was defficult because I had to use a flash light to see on the screen. Lastly, i just click reboot and then the phone lights up perfectly and HTC logo comes up and then it blanks off again. So can anyone help? any advise
Sent from my HTC One using XDA Free mobile app
keronmat said:
Lastly, i just click reboot and then the phone lights up perfectly and HTC logo comes up and then it blanks off again. So can anyone help? any advise
Sent from my HTC One using XDA Free mobile app
Click to expand...
Click to collapse
Find the way to install adb and communicate with the phone via adb and fastboot. If you can do that, you will be able to install anything necessary to get the phone working again.
First however, remove the battery, wait a few seconds, reinsert the battery and charge the phone overnight. Next day, try and start phone usual way--see what happens.
If NOTHING happens and you get a black screen, remove battery again for a few seconds, reinsert, and this time hold the power button in for AT LEAST 20 seconds.
See if that starts the phone.
If you get absolutely nothing again, find the "Unbricking Project" thread, but if you get any kind of screen, see if you can boot to recovery and restore anything. If you get a screen but can't do any kind of restore at all, find instructions for adb and fastboot I mentioned earlier, so you can install a new recovery and flash a new rom..
I did everything you said. Except I complete forget how to flash recovery and custom rom from my pc but when I type command in fastboot "adb devices" it was successful.
However, I charge the phone and I got into the recovery mode again and the wipe everything and then click backup and recovery. I rebooted the phone and it came on as if its a brand new HTC Amaze. I had the phone working i rejoice for a bit and then I realize I forget to put in my sim card. So i turn the phone off, put in the sim card. The same problem again. No led, no light in the screen, the phone atomatically boots into recovery mood.
One more thing. when booting into recovery mode. the phone doesn't go where I see the 3 android at the bottom and you see, fastboot, reset etc. It goes straight to cwm screen.
keronmat said:
One more thing. when booting into recovery mode. the phone doesn't go where I see the 3 android at the bottom and you see, fastboot, reset etc. It goes straight to cwm screen.
Click to expand...
Click to collapse
I think that is what you should see when you boot into recovery.
Do whatever you did before to get the phone lit up again, then change the display settings to maybe 3/4 brightness for instance. Reboot the phone normal reboot and see if it comes back with light.
If it does, maybe you are fixed enough to install the sim.
Do you possibly have a nandroid backup saved somewhere, you could put it back in the phone via recovery?
The phone is lit up again like you asked me to do. It was hard to see in recovery mode. But i used a flashlight to look on the screen of the AMAZE then i flash a new custom rom. After multiple tries I got it up. SO its up and the brightness is at its highest point. But I dont believe thats the problem. I just need to figure out how the light stays off when in recovery mood but comes on when booted normally. Its as though the recovery is broken. How do I fix it? if its broken

Categories

Resources