Hi, I am having problem with my samsung galaxy s6102.I flashed my phone with S6102_DDLG1_ODDLF1_DDLG1_INU_wipe_by_manoranjan2050.org using Odin.After flashing it got stuck in the samsung logo then kept restarting...Then i removed the battery and put it in again.Then i could see the setup screen where it says "touch the android to begin".But the touch screen is not working after that .Volume,power button and home button works fine only the touch screen not working.. I flashed it many times but the touch screen wont work. Please help me how to solve this problem.Thanks
Me too! Is there anybody who knows a fix??
sanjoyd4 said:
Hi, I am having problem with my samsung galaxy s6102.I flashed my phone with S6102_DDLG1_ODDLF1_DDLG1_INU_wipe_by_manoranjan2050.org using Odin.After flashing it got stuck in the samsung logo then kept restarting...Then i removed the battery and put it in again.Then i could see the setup screen where it says "touch the android to begin".But the touch screen is not working after that .Volume,power button and home button works fine only the touch screen not working.. I flashed it many times but the touch screen wont work. Please help me how to solve this problem.Thanks
Click to expand...
Click to collapse
I have got the same probleme, and have tried every available solution....I hope not! Are there any kind of fix beside flashing with Odin(with & without Pit-file), tried flashing new Rom.....
After flashing everything looks good until I have to punch in Pin for my Sim-card......No go:crying:
Any tip will be appreciated
I found the solution Firmware(Chile) for Gt-s6102B did it!!! Downloaded (S6102BVJMC2_S6102BCHOMD1_CHO)
from sammobile(free registration needed)
used Odin 3 v3.07..........(run as admin)
Only add "pad-file"....
Hit start, and a few minutes later....Voila..Touch is working again
sanjoyd4 said:
Hi, I am having problem with my samsung galaxy s6102.I flashed my phone with S6102_DDLG1_ODDLF1_DDLG1_INU_wipe_by_manoranjan2050.org using Odin.After flashing it got stuck in the samsung logo then kept restarting...Then i removed the battery and put it in again.Then i could see the setup screen where it says "touch the android to begin".But the touch screen is not working after that .Volume,power button and home button works fine only the touch screen not working.. I flashed it many times but the touch screen wont work. Please help me how to solve this problem.Thanks
Click to expand...
Click to collapse
http://www.mediafire.com/download/t...MA3_S6102OJPMA3_S6102XXMA2_HOME.tar.part1.rar
http://www.mediafire.com/download/1...MA3_S6102OJPMA3_S6102XXMA2_HOME.tar.part2.rar
odin 3.07
POST RESULT AFTER
B.R
ELGHANDOR
GT-S6102 After flash touchpad not working Solution.....!!
1. Flash with Odin307
2.file is S6102DDMF4_S6102ODDMF4_S6102DDMF4_HOME.tar.md5
Thanks in Arabic ...... شكرا
elghandor said:
http://www.mediafire.com/download/t...MA3_S6102OJPMA3_S6102XXMA2_HOME.tar.part1.rar
http://www.mediafire.com/download/1...MA3_S6102OJPMA3_S6102XXMA2_HOME.tar.part2.rar
odin 3.07
POST RESULT AFTER
B.R
ELGHANDOR
Click to expand...
Click to collapse
Thanks in Arabic .... شكرا
:good: :good:
I am too looking for solution
I also got the same problem can you tell me how to flash the mobile? As i am noob in this things! can you step by step instructions??
teiningen said:
I have got the same probleme, and have tried every available solution....I hope not! Are there any kind of fix beside flashing with Odin(with & without Pit-file), tried flashing new Rom.....
After flashing everything looks good until I have to punch in Pin for my Sim-card......No go:crying:
Any tip will be appreciated
I found the solution Firmware(Chile) for Gt-s6102B did it!!! Downloaded (S6102BVJMC2_S6102BCHOMD1_CHO)
from sammobile(free registration needed)
used Odin 3 v3.07..........(run as admin)
Only add "pad-file"....
Hit start, and a few minutes later....Voila..Touch is working again
Click to expand...
Click to collapse
teiningen said:
I have got the same probleme, and have tried every available solution....I hope not! Are there any kind of fix beside flashing with Odin(with & without Pit-file), tried flashing new Rom.....
After flashing everything looks good until I have to punch in Pin for my Sim-card......No go:crying:
Any tip will be appreciated
I found the solution Firmware(Chile) for Gt-s6102B did it!!! Downloaded (S6102BVJMC2_S6102BCHOMD1_CHO)
from sammobile(free registration needed)
used Odin 3 v3.07..........(run as admin)
Only add "pad-file"....
Hit start, and a few minutes later....Voila..Touch is working again
Click to expand...
Click to collapse
thanks , i was having the same problem so i followed your steps and it worked for me (GT-s6102B) but it was missing Arabic so i flashed S6102JPMA3_S6102OJPMA3_S6102XXMA2_HOME.tar.md5 (GT-s6102) and it worked and arabic was installed
many thanks again
so, google brings this up for the problem, but i couldn't get odin to flash the full package from sammobile to the 6102B, getting splitfus2 to work was a bit of a riddle (64biit version doesn't have necessary libraries for it in cygwin need 32bit version to work) anyways, i created a few of them thought it might help anyone else with this issue and who are less tech savvy. these worked for me, there are BR and Chile roms for the 6102B, flashing non B roms seem to leave touchscreen unresponsive after flashing the phone.
links:
S6102B_VJMA2_ZTRMA2_VJMA2_wipe_by_SplitFUS2.zip 136.7 MB
https://mega.co.nz/#!TlAg0DyT!jlhrrTmg-EMTLLrMAXlQucfrUceG_dxrYQs00kEz058
S6102B_VJMC2_CHOMD1_VJMC3_wipe_by_SplitFUS2L.zip 123.0 MB
https://mega.co.nz/#!yxZCFJRJ!FzHpXR3uD7YjGRhiHN2BsNktqw9E7KJE88F9WE9UmMA
S6102B_VJME1_CHOME1_VJME1_wipe_by_SplitFUS2.zip 122.2 MB
https://mega.co.nz/#!vtR23CwJ!Bek7_29TNu3RbRVUjHqGAYBLVEwgUHieg6nOb0aN1wc
S6102B_VJME1_ZTOMI1_VJME1_wipe_by_SplitFUS2.zip 135.3 MB
https://mega.co.nz/#!25YQyD6T!ygTbUseF4uWQCA1hzEkiOS8zT2YSH1QMXkLGdwh0F6I
take no credit, just used splitfus2 to split the tar.md5 from sammobile and uploaded them to mega. worked to fix the 6102B, it went to reboot loop, flashed a 6102 rom with which touch didn't work.
sorry to bring ancient thread up, if anyone has this issue google will make it an easy fix pointing to this thread as it did for me.
Related
My Samsung Tablet stops at the start up screen, choose the language then start. Does not respond to touch. I used an ODIN program. But when re-running stops at the same screen. What is the solution?
Thank you
alharbi said:
My Samsung Tablet stops at the start up screen, choose the language then start. Does not respond to touch. I used an ODIN program. But when re-running stops at the same screen. What is the solution?
Thank you
Click to expand...
Click to collapse
You need to give a lot more information if you want help. Which version of the tab do you have? What did you flash with ODIN? more info...
Samsung Galaxy Tab 10.1, the slim one. Comes with 3.1 honeycomp. I flashed it with Arabic 3.1.
Thank you for your help.
alharbi said:
Samsung Galaxy Tab 10.1, the slim one. Comes with 3.1 honeycomp. I flashed it with Arabic 3.1.
Thank you for your help.
Click to expand...
Click to collapse
Was it working out-of-the-box? Did you try to root it? give more detail about your tab software version, what steps you performed? so that people in this forum can provide some guide you.
It was working. I an not try to do root for it. The problem comes after I installed Dr. Wen Antivirus. While the programme scaning it reboot the device. But it stopped on the first screen to choose the language. No respose for the touch.
Software 3.1 - I used Odin, every thing go perfect. But when start stop on the same screen and same problem.
I dont have idea about the tab software ver. Thank you
alharbi said:
It was working. I an not try to do root for it. The problem comes after I installed Dr. Wen Antivirus. While the programme scaning it reboot the device. But it stopped on the first screen to choose the language. No respose for the touch.
Software 3.1 - I used Odin, every thing go perfect. But when start stop on the same screen and same problem.
I dont have dea about the tab software ver. Thank you
Click to expand...
Click to collapse
Maybe you have to use volume buttons to choose the language.
sent from my CM7 nokia 3210
Hi everyone
i live in north africa in algeria
i tried to flash my i9100G nwith the latest stock ics
everytjing went well unitil a big red fail apeared on odin
my phone doesn t turn on i got a pc with phone they told this is the sead screen
whatever please help me to slove this problem
& thanks for every one
I flashed ics xxlpq
no problem just flash the stock rom again but this time with pit
Hello,
please see this excellent repair guide:
http://forum.xda-developers.com/showthread.php?t=1448765
and let us know if it works for you.
can you give me a link for a stock rom with the pit file & thanks alot
nouninou said:
can you give me a link for a stock rom with the pit file & thanks alot
Click to expand...
Click to collapse
Did you even read the tutorial??, there clearly states where to download the files,
thats why you bricked your phone, you have to readdd everything and understand things before going up
I hope this options works for you !!
Hey, read this options to solve this problem. The second option Worked for me
1. if you´re phone doesn´t turn on and the screen not response maybe the problem is a hardbrick,
2.if you´re galaxy doesnt turn on but in the screen appears icons, the trouble is softbrick.
1.The solution for a hardbrick is a JTAG, this is a used method by Tecnics
2. The solution for a softbrick is a reinstall , just put the galaxy in download mode and install a official firmware with odin and done
after downloading a pit file it works
thank you very much
Dear All,
I hope someone can help me get out of the situation.
I am using this FEITENG HTM H9001 6 Inches China Phone.
It came rooted by the vendor.
It is a good and nice phone. And I like it alot.
After I install a "font changing" apps,
The phone auto shut off and restart and it stuck at the HTM logo.
So sad Sad.
I know I need to reflash the firmware.
So I did some search on line...............
After finally managed to install the USB's driver which I was not able for quite long....
I follow the instruction on youtube from this site.
Down loaded the flast tool - SP Flash Tool v3.1332.0.sn187
Go to needrom to get a HTM H9001 firmware.
It should be there "right firmware". Someone there on the page where i got the firmware for H9001 said that its stable after he flash it. So proceeded to download it. Safely assume its the correct rom.
Using the flashtool, I followed the flashing steps exactly untill the green sign appeared. I was looking forward to see it start again after the problem mentioned above...........
After pulling out the cables from my PC, I press the power/start button of the phone to check if its ok....BUT It did started but it only shows "whitish color screen"
I can't even see the usual green colour HTM logo when the phone was switched on but I can hear sound of the phone starting... it stays at the whitish screen. And when I touch certain part of the screen the phone seem to response...just that I cannot view the desktop and the icon.. perhaps the video driver was corrupted in some way...or could it be the wrong rom
I proceeded re-flash it again........
same result - white screen.... phone still response to " power switch when press the LCD goes off. and some responsive sounds when the blank screen is touhed...
I am here in hope for some luck in finding ways to recover my phone back to normal...
It all started from installing a font changing apps that corrupted the firmware...than perhaps my action may have complicate the situation further....
Please. Any help would be great.
Thanks so much in advance.
How can I make good back my Feiteng HTM H9001
Or did I got the wrong ROM ?
It did not stae Feiteng just H9001 .
The rom I downloaded for my phone is here for my Feitend HTM H9001.
Is this the correct rom for my phone ?
Appreciate , really needs help to get out from this problem.
I love this phone. I want to make it good again Smile
I will try to upload some image to show its current stae.
many Thanks in advance.
Desmond
So desperate..I uses this MTK Droid tools.
I turn the phone on and it detected the details on my phone.....
Is there any way to use other tools to get my phone back to working like before the "font changing apps" time .... it was working great just before with no problem at all.............
MTK droid can detec the details of my phone...........
BUT i am lost - any way to use Droid tools to save the situation ?
I attached some picture to share what I meant...
Hope some nice great guys can shed some lights so i can try to move ahead..currently really lost... newbies to android phone....
Many Thanks
Anyone can help ?
How do I redo the rom all over from scratch ?
Or can I try to reflash other rom or install say other OS on my phone ?
Just want to make it work again..............
Thanks
Repair HTM H9001
moneycow said:
Anyone can help ?
How do I redo the rom all over from scratch ?
Or can I try to reflash other rom or install say other OS on my phone ?
Just want to make it work again..............
Thanks
Click to expand...
Click to collapse
Hello friend,
if you want to recover your H9001 look this link:
movilesdualsim com htm6582
on the site will explain the steps to solve your problem.
To me it happened to me same thing that has happened to you.
And now I enjoy my H9001 more than ever.
regards
Hello guys, i need little help with my phone, so here is what happened: Two days ago i tried to turn on my phone, it started booting but the cycle repeated again and again so I got in recovery and wiped data/catche, but that didn`t helped. I thought that if i change the rom maybe I can fix the problem so I downloaded my rom from needrom (there were 2 roms for my device) and started flashing with Flash tool. I downloaded the first rom to my phone and tried to turn the phone on but nothing happened.. I downloaded the second rom and it worked, the phone booted but the only think that I can see is blank white screen, the touch is working and the buttons, when i click somewhere i feel the device vibrating but thats it. One time i managed to make the device appear in my computer as a normal android phone, dont know how this happened. So can someone help me please, if you have a phone like mine can you backup your rom and send it to me or help me find a working one, or some idea how to fix the blank screen. Thanks in advance
someone :/
t0shko0 said:
someone :/
Click to expand...
Click to collapse
I`m really desperate :X . I thought about porting other android from similiar MKT device but how can I do that when i don`t have a working one.
t0shko0 said:
Hello guys, i need little help with my phone, so here is what happened: Two days ago i tried to turn on my phone, it started booting but the cycle repeated again and again so I got in recovery and wiped data/catche, but that didn`t helped. I thought that if i change the rom maybe I can fix the problem so I downloaded my rom from needrom (there were 2 roms for my device) and started flashing with Flash tool. I downloaded the first rom to my phone and tried to turn the phone on but nothing happened.. I downloaded the second rom and it worked, the phone booted but the only think that I can see is blank white screen, the touch is working and the buttons, when i click somewhere i feel the device vibrating but thats it. One time i managed to make the device appear in my computer as a normal android phone, dont know how this happened. So can someone help me please, if you have a phone like mine can you backup your rom and send it to me or help me find a working one, or some idea how to fix the blank screen. Thanks in advance
Click to expand...
Click to collapse
Same problem with me.
I downloaded the rom from NEEDROM.COM.
chery22 said:
Same problem with me.
I downloaded the rom from NEEDROM.COM.
Click to expand...
Click to collapse
Have the same problem. I also downloaded the rom from Needrom.com and after installing the software I have a white screen and unable to use the device. Anybody solved already this matter? Help would be very much appreciated. Thanks.
PitNaw said:
Have the same problem. I also downloaded the rom from Needrom.com and after installing the software I have a white screen and unable to use the device. Anybody solved already this matter? Help would be very much appreciated. Thanks.
Click to expand...
Click to collapse
me to
has anybody a original ROM for the N800+?
While trying to update Kernel recovery version TWRP from the G925 to the G920, the update completed successfully, but when the device booted I noticed that the touch pad was working in reverse.
When I touch one side the opposite side responds.
All of my attemps to restore the decive to original ROM with PIT were successful, but the touch pad is still working in reverse.
Please, can someone help me, is there any hidden menu or option that can calibrate the screen/touchpad back to nomal ?
SHATTAH said:
While trying to update Kernel recovery version TWRP from the G925 to the G920, the update completed successfully, but when the device booted I noticed that the touch pad was working in reverse.
When I touch one side the opposite side responds.
All of my attemps to restore the decive to original ROM with PIT were successful, but the touch pad is still working in reverse.
Please, can someone help me, is there any hidden menu or option that can calibrate the screen/touchpad back to nomal ?
Click to expand...
Click to collapse
Can you please update us what you did to fix it?
Where did you found PIT files for S6.
Thank you.
@SHATTAH
have you try :
1: if you can save all your data , because all will be deleted after( 2 and 3 )
2: factory reset with the keyboard dial : *#87976633# and reboot your phone
3: recovery mode for wiping cache partition and data/factory reset http://wgnszoz9s1.1fichier.com/
regards
fix
Dear friends I was able to fix the problem. To enter dialer
*#2663# and then windows open and press on
Tap fw update general and then fix
Can you plase add I pic...
Did you still have to Flash STOCK rom+Factoy reset or only the code...?
Thanks :good:
This is the screen shot you ask...
had same problem with my newly bought s6 within 2 days after putting custom rom , immediately i went to samsung service centre , as the device is just two days old, they replaced the device with new one., Even after i had Knox warrenty void:1
-JFK- said:
This is the screen shot you ask...
Click to expand...
Click to collapse
Thanks Alot,
Your are A Guy of Great Clever. I will ever Thanks to You.
Thanks A lot Sir......
SHATTAH said:
Dear friends I was able to fix the problem. To enter dialer
*#2663# and then windows open and press on
Tap fw update general and then fix
Click to expand...
Click to collapse
Thank you so much!
SHATTAH said:
While trying to update Kernel recovery version TWRP from the G925 to the G920, the update completed successfully, but when the device booted I noticed that the touch pad was working in reverse.
When I touch one side the opposite side responds.
All of my attemps to restore the decive to original ROM with PIT were successful, but the touch pad is still working in reverse.
Please, can someone help me, is there any hidden menu or option that can calibrate the screen/touchpad back to nomal ?
Click to expand...
Click to collapse
Hi Shattah.
Do you remember the which version of TWRP of the G925 (edge) did you use on the G920 (flat)? Was it the chinese, the t-mobile, or some other? Trying to install TWrp on my s6 g920i flat (demo unit) and no luck so far. Please let me know and I'll try that trick. Cheers.
is that command supposesed to work with default os that comes with the s6 edge. U went in the phone field and pasted the code where my phone reponded by telling me I was dialing a wrong number.
Thanks
SHATTAH said:
Dear friends I was able to fix the problem. To enter dialer
*#2663# and then windows open and press on
Tap fw update general and then fix
Click to expand...
Click to collapse
thanks mybro.. :* :*
SHATTAH said:
Dear friends I was able to fix the problem. To enter dialer
*#2663# and then windows open and press on
Tap fw update general and then fix
Click to expand...
Click to collapse
thank you a lot, you saved my phone