I am working on building from aosp 4.4.2. I have built it with the pre-built kernel without any problems. Then, I managed to get a custom kernel code in place and it builds. Now the only thing left to do is the initramfs/ramdisk for the custom kernel I have in place. Currenlty my build will not boot. I suspect it is using the initramfs/ramdisk from aosp.
Can someone point me to the source files or files that handle the initramfs/ramdisk? I have found bits and pieces strewn throughout the source code but cannot pinpoint the indivitual files or the script/mk file that produces the ramdisk found in the out folder after my system finishes building.
I kinow I can change the initramfs/ramdisk manually by repacking the boot.img, but I would prefer everything be completed in the updatpackage.
what device do you have?
Anyways, just decompile the working boot.img with dsixda's kitchen, and replace the zImage, build it again and done
broodplank1337 said:
what device do you have?
Anyways, just decompile the working boot.img with dsixda's kitchen, and replace the zImage, build it again and done
Click to expand...
Click to collapse
I have a Nexus 5. I'm trying to avoid the, "build it again."
I would like to envsetup, lunch, make clean, make updatepackage, flash and done.
So, I'm still trying to figure out, how make knows where to get all the files and create the ramdisk in the out directory.
AOSP radisk
I am no expert but I think this is how ramdisk is built and it worked for me al the time. ramdisk is composed from the directory 'root' in the product build output folder. the contents are coming from different part of the build tree, mostly from the device source, vendor source. for eg:- check hammer head tree for omni https://github.com/omnirom/android_device_lge_hammerhead in the device.mk you can see PRODUCT_COPY entries to the root similar thing goes with vendor makefiles. If you are looking for executable built from source you can set
LOCAL_MODULE_PATH := $(TARGET_ROOT_OUT) so that they will end up in initrd
related to this: I can see using PRODUCT_COPY_FILES to stage files to the root directory. but where is the directory structure created? Such as /firmware ... etc? I am trying to add a directory to the root fs. When I just create a new directory such as /foo the build fails. I want the new directory to be permanent part of the build process so solutions like unpack - modify - repack is less than satisfactory. Thanks
Related
Hi,
Followed cyanogen's instruction in his wiki, I could build and flash my own ROM to N1, and it is working. Thanks cyanogen so much for everything he has done with Android.
However, the instruction is based on cyanogen's source code. Now, I am trying to figure out how to build a new ROM from pure Android source code (i.e. the one from AOSD).
I obtained the eclair branch as follows:
Code:
repo init -u git://android.git.kernel.org/platform/manifest.git -b eclair
repo sync
My questions are:
1. There is not any directory under ./vendor for N1 (i.e. passion). I can see only directories for Dream & Sapphire. Does it mean I can build only ROM for Dream/Sapphire? The following result seems support that point. Did I misunderstand some points?
Code:
$ sed -n -e "s/^add_lunch_combo//gp" vendor/*/vendorsetup.sh
aosp_emulator_us-eng
aosp_emulator_eu-eng
aosp_dream_us-userdebug
aosp_dream_eu-userdebug
aosp_dream_us-eng
aosp_dream_eu-eng
aosp_sapphire_us-userdebug
aosp_sapphire_eu-userdebug
aosp_sapphire_us-eng
aosp_sapphire_eu-eng
2. There is not extract-files.sh there. So I suppose I need to use the file from cyanogen. But what else should I do to be able build a new ROM?
Any help is really appreciated!
I'm just as clueless as you are to this--but when I compiled for the HTC Touch, all I did was pull down the stock AOSP build (repo sync) and simply ran "make" from the root directory, which produced a blank System image.
From there, I either copy & pasted the compiled library .so files into the image (to provide driver support), or if necessary to have the source compiled for the version, I included the source into the repo sync directory and ran the "make" which would also produce a compiled library.so that functioned.
Not sure any of this will help, but I figured I'd offer what I could.
Shidell said:
I'm just as clueless as you are to this--but when I compiled for the HTC Touch, all I did was pull down the stock AOSP build (repo sync) and simply ran "make" from the root directory, which produced a blank System image.
From there, I either copy & pasted the compiled library .so files into the image (to provide driver support), or if necessary to have the source compiled for the version, I included the source into the repo sync directory and ran the "make" which would also produce a compiled library.so that functioned.
Not sure any of this will help, but I figured I'd offer what I could.
Click to expand...
Click to collapse
Thanks Shidell. So you meant that it worked for your HTC Touch?
How do you copy & paste library files into image?
How do you include the source into the repo sync directory?
Hi, for those interested I wrote following steps (ubuntu 10.10 32b):
(based on excellent http://android-dls.com/wiki/index.php?title=HOWTO:_Unpack,_Edit,_and_Re-Pack_Boot_Images )
I included compiled tools mkbootfs , mkbootimg and perl scripts unpack-bootimg.pl and repack-bootimg.pl.
Repack-bootimg.pl is edited and the needed parameters for our folio are included ([email protected] [email protected] vmalloc=192M video=tegrafb console=ttyS0,115200n8 usbcore.old_scheme_first=1 tegraboot=sdmmc tegrapart=recovery:122000:a00:800,linux:a0e00:1000:800,loader:300:400:800,mbr:700:200:800,system:900:20000:800,cache:20900:80000:800,misc:a0900:400:800,userdata:a1f00:80000:800 boardtype=PR)
1) unpack attachement mytools.tgz into your home, in your home the folder ~/mytools is created:
tar -xzf mytools.tgz
2) copy existing boot.img into ~/mytools (from foliomod update.zip)
3) ./unpack-bootimg.pl boot.img
- old kernel from boot.img is extracted: boot.img-kernel.gz
- content of contained ramdisk is extracted in folder: boot-img.ramdisk
4) copy new compiled kernel (zImage) into ~/mytools (from <source>/kernel/arch/arm/boot/zImage , you have to compile yourself with the weeds2000 quide http://forum.xda-developers.com/showthread.php?p=10331797#post10331797)
5) make all desired changes into ramdisk folder
6) repack new boot.img with a new kernel and changed ramdisk
./repack-bootimg.pl zImage boot.img-ramdisk boot-new.img
7) new boot image is created as boot-new.img
8) if you want just to experiment, you can take any full foliomod dexter's update.zip (1.3d), put the new boot image inside instead original one.
It is possible to remove the other 2 images (recovery and system) if you want just to flash kernel. NOTE! But you have to remove the extrating command for recovery and system from update.zip/meta-inf/com/google/android/update-script.
p.s. Feel free to correct me, if something wrong with the steps. It's my first attempt to compile kernel
I am on FolioMod 1.3d and I use the kernel built without patches from http://tegramid.com/wiki/Main_Page(Full GPL source bundle including framework) for a day without problems. I had to do a full wipe. It's meant for testing, I don't say that kernel from source is better or worse.
Many thanks to Dexter because everything is based on his release, weeds2000 because of his kernel compile quide and tsh who placed the sources on the git and to all who try hacking our folio
thx for this, that 'll be usefull
thanks for the guide.
i have managed to do every thing up to the repack
when i type
Code:
perl repack-bootimg.pl boot.img-kernel.gz boot.img-ramdisk.gz boot.img
i get error
Code:
boot.img-ramdisk.gz Not a directory at repack-bootimg.pl line 13.
even though it is definatly in their. any idea how to get it to work?
You don't have to provide the folder instead of the packed Ramdisk-File!
Because this script is made doing changes in Ramdisk and kernel..
So you can change the scripts inside the boot.img-ramdisk folder and the script will repack and add it to the new boot.img!
permission denied
i have done everything as you said, but while using split_bootimg.pl i got "permission denied". please suggest me what to do?
1. Enable read/write permissions for that file.
2. Tobr, you made a mistake in repack-bootimg.pl. You forgot to add " ./ " before mkbootimg.
Jon2555 said:
1. Enable read/write permissions for that file.
2. Tobr, you made a mistake in repack-bootimg.pl. You forgot to add " ./ " before mkbootimg.
Click to expand...
Click to collapse
The script was downloaded from internet not written by me. And it worked for me just fine. I can not verify now that you are right (probably you are). If it works for you with ./ then either I can put fixed version for download for others (if there is anybody) or it can be here just as a notice for other users, if not working.
I have ./ defined in my path variable in my profile so that i don't need it.
eror when repack
tobr said:
Hi, for those interested I wrote following steps (ubuntu 10.10 32b):
(based on excellent http://android-dls.com/wiki/index.php?title=HOWTO:_Unpack,_Edit,_and_Re-Pack_Boot_Images )
I included compiled tools mkbootfs , mkbootimg and perl scripts unpack-bootimg.pl and repack-bootimg.pl.
Repack-bootimg.pl is edited and the needed parameters for our folio are included ([email protected] [email protected] vmalloc=192M video=tegrafb console=ttyS0,115200n8 usbcore.old_scheme_first=1 tegraboot=sdmmc tegrapart=recovery:122000:a00:800,linux:a0e00:1000:800,loader:300:400:800,mbr:700:200:800,system:900:20000:800,cache:20900:80000:800,misc:a0900:400:800,userdata:a1f00:80000:800 boardtype=PR)
1) unpack attachement mytools.tgz into your home, in your home the folder ~/mytools is created:
tar -xzf mytools.tgz
2) copy existing boot.img into ~/mytools (from foliomod update.zip)
3) ./unpack-bootimg.pl boot.img
- old kernel from boot.img is extracted: boot.img-kernel.gz
- content of contained ramdisk is extracted in folder: boot-img.ramdisk
4) copy new compiled kernel (zImage) into ~/mytools (from <source>/kernel/arch/arm/boot/zImage , you have to compile yourself with the weeds2000 quide http://forum.xda-developers.com/showthread.php?p=10331797#post10331797)
5) make all desired changes into ramdisk folder
6) repack new boot.img with a new kernel and changed ramdisk
./repack-bootimg.pl zImage boot.img-ramdisk boot-new.img
7) new boot image is created as boot-new.img
8) if you want just to experiment, you can take any full foliomod dexter's update.zip (1.3d), put the new boot image inside instead original one.
It is possible to remove the other 2 images (recovery and system) if you want just to flash kernel. NOTE! But you have to remove the extrating command for recovery and system from update.zip/meta-inf/com/google/android/update-script.
p.s. Feel free to correct me, if something wrong with the steps. It's my first attempt to compile kernel
I am on FolioMod 1.3d and I use the kernel built without patches from http://tegramid.com/wiki/Main_Page(Full GPL source bundle including framework) for a day without problems. I had to do a full wipe. It's meant for testing, I don't say that kernel from source is better or worse.
Many thanks to Dexter because everything is based on his release, weeds2000 because of his kernel compile quide and tsh who placed the sources on the git and to all who try hacking our folio
Click to expand...
Click to collapse
hi
when do this in ubuntu 11.4
get eorr below
[email protected]:~/Desktop/untitled folder$ ./unpack-bootimg.pl boot.img
kernel written to boot.img-kernel.gz
ramdisk written to boot.img-ramdisk.cpio.gz
463 blocks
extracted ramdisk contents to directory boot.img-ramdisk/
[email protected]:~/Desktop/untitled folder$ ./repack-bootimg.pl zImage boot.img-ramdisk boot-new.img
gzip: folder/ramdisk-repack.cpio.gz: No such file or directory
sh: mkbootimg: not found
No such file or directory at ./repack-bootimg.pl line 21.
[email protected]:~/Desktop/untitled folder
can any one help me?
any tools for windows ?
nguyenhonganh said:
any tools for windows ?
Click to expand...
Click to collapse
Same request!
repack problem
Can somebody tell me is it possible to repack kernel and ramdisk using just hex editor? Without this scripts and unmkbootimg and mkbootimg. What does not work for me cos im using i9100 Philz root. I know how to unpack it and change init.rc and pack it back again. So can i just put my (kernel+ramdisk) ramdisk.cpio.gz file inside mmcblk0p5 in exac location. Will that work out? I dont know what this is doing:
mkbootimg --kernel zImage --ramdisk initramfs.cpio.gz --base 0x20000000
--cmdline 'no_console_suspend=1' -o new_boot.img
this address thing and cmdline but if i replace just ramdisk i dont need to set up addres again cos everything will be in same place. And one more question if something goes wrong can i boot to recovery or download mode?
New kernel copied itself to mmcblk0p5
and i have new CWM now. So it seems to me recovery is inside mmcblk0p5 as well and my phone never use mmcblk0p6
@tobr, I cannot open the archive of boot.img-kernel.gz. When I try to open it with terminal, it says: Not a valid gzip file. What to do?
Hi
I want to add to my custom ROM a new group id, which I have defined in the file "android_filesystem_config.h".
In general, this file will be included by the android source code, unfortunately my custom ROM has it also built in it sources and I don't have access to this header file.
Then I saw, that android kitchen has in its folder tools/mkboot the file "android_filesystem_config.h". How is this config file used by the kitchen, has it any influence on building the boot.img in the tool or not?
I tried to build a boot.img by running
Code:
mkbootimg --kernel zImage --initrd.gz -o boot.img
, but the modified android_filesystem_config.h did not have any influence. What is the tool mkbootfs for?
Is it even possible to patch a boot.img whit new gid information or do I have to rebuild a whole ASOP?
Thanks and regards
cloooned
So, I'm doing this tutorial due to the trial and error I got.
Prerequisites:
Ubuntu or any linux-based os with the right packages installed
Source code from the kernel
Backup of you boot partition
These tools here
Patience
1) The first thing you want to do is to do a backup of your boot partition.
Code:
adb shell
dd if=/dev/block/mmcblk0p9 of=/sdcard/boot.img
2) Download the source code from here, extract it and place it somewhere. I placed it in /home/fabio/Documentos/Kernel/sourcecode
3) Download a toolchain, I downloaded "aarch64-linux-android-4.8" from google and placed in "/home/<your username>/Documentos/Kernel/aarch64-linux-android-4.8"
4) Go to your kernel source code and find the file "Makefile", open it and change CROSS_COMPILE= to say the place where you stored the toolchain "/home/<your username>/Documentos/Kernel/aarch64-linux-android-4.8" + "/bin/aarch64-linux-android-"
5) Now that you are done setting up the stuff, open a console and navigate to your kernel source code root and type
Code:
make
make pxa1908_grandprimevelte_eur_defconfig
make -j#
# is the number of cores + 1
6) While that runs, go to where you stored those mkbootimg tools and unpack that boot.img you backed up
7) Once the kernel building is complete. Go to your kernel folder and navigate to arch/arm64/boot and copy the file "Image.gz"
8) Download bless or an Hex Editor of your liking and open the following files: boot.img (the original boot), Image.gz, boot.img-zImage.
Search on the "boot.img-zImage" for 1F 8B 08 and copy everything before then on your Image.gz place what you copied and save it as a different file otherwise it will fail to save.
9) Go to your mkbootimg folder and where you stored the unpacked files and build one boot.img with the following command
Code:
./mkbootimg --kernel image2.gz --ramdisk boot.img-ramdisk.gz --dt boot.img-dt --signature boot.img-signature -o boot2.img
10) Flash the boot2.img using any software you want!
THIS MIGHT NOT WORK! If it doesn't you can send me a DM! I will be retouching this post again and make it prettier adding pictures and stuff but for now I can't do much!
If you know a better way of doing this please say in the replies! I will be building a kernel for this device soon enough
RESERVED
Can you please upload link of custom kernel
I'm still trying to do a kernel with new features, but don't know what to add yet. Trying to make Init.d support without 3rd party apps!
EDIT1: I give up! My phone is too much trouble and since SAMSUNG doesn't care about it neither do I anymore! Try to build the kernel yourself and tweak it as you like! Make a script to automate this process to be easier! Good luck! Anything you need just say
Can you help this guy for porting kernel source code http://forum.xda-developers.com/grand-prime/general/developers-discussion-sm-g531f-custom-t3444598
fabiossilva21 said:
So, I'm doing this tutorial due to the trial and error I got.
Prerequisites:
Ubuntu or any linux-based os with the right packages installed
Source code from the kernel
Backup of you boot partition
Degas mkbootimg tools
Patience
1) The first thing you want to do is to do a backup of your boot partition.
Code:
adb shell
dd if=/dev/block/mmcblk0p9 of=/sdcard/boot.img
2) Download the source code from here, extract it and place it somewhere. I placed it in /home/fabio/Documentos/Kernel/sourcecode
3) Download a toolchain, I downloaded "aarch64-linux-android-4.8" from google and placed in "/home/fabio/Documentos/Kernel/aarch64-linux-android-4.8"
4) Go to your kernel source code and find the file "Makefile", open it and change CROSS_COMPILE= to say the place where you stored the toolchain "/home/fabio/Documentos/Kernel/aarch64-linux-android-4.8" + "/bin/aarch64-linux-android-"
5) Now that you are done setting up the stuff, open a console and navigate to your kernel source code root and type
Code:
make
make pxa1908_grandprimevelte_eur_defconfig
make -j#
# is the number of cores + 1
6) While that runs, go to where you stored degas-mkbootimg tools and unpack that boot.img you backed up
7) Once the kernel building is complete. Go to your kernel folder and navigate to arch/arm64/boot and copy the file "Image.gz"
8) Download bless (Hex Edit) and open the following files: boot.img (the original boot), Image.gz, boot.img-zImage.
Search on the "boot.img-zImage" for 1F 8B 08 and copy everything before then on your Image.gz place what you copied and save it as a different file otherwise it will fail to save.
9) Go to your degas-mkbootimg folder and where you stored the unpacked files and build one boot.img with the following command
Code:
./degas-mkbootimg --kernel image2.gz --ramdisk boot.img-ramdisk.gz --dt boot.img-dt --signature boot.img-signature -o boot2.img
10) Flash the boot2.img using any software you want!
THIS MIGHT NOT WORK! If it doesn't you can send me a DM! I will be retouching this post again and make it prettier adding pictures and stuff but for now I can't do much!
If you know a better way of doing this please say in the replies! I will be building a kernel for this device soon enough
Click to expand...
Click to collapse
i follow this step and build kernel after flash boot.img phone not booting
my boot.img size is 8.2MB (image.gz size 6.5MB) where stock size is 8MB
is problem with size?
sorry for my bad english
How did you flash the boot.img?
fabiossilva21 said:
How did you flash the boot.img?
Click to expand...
Click to collapse
using odin
What changes did you make to the kernel?
fabiossilva21 said:
What changes did you make to the kernel?
Click to expand...
Click to collapse
Add governors
Other setting same as stock
If i build with stock setting without any changes then kernel boot but if i change something then its stuck on Samsung logo
Sorry, I can't really help you... I no longer work with Grand prime... switched to a J5
fabiossilva21 said:
Sorry, I can't really help you... I no longer work with Grand prime... switched to a J5
Click to expand...
Click to collapse
Ok
Noice
Recently I started making device tree ( I found common repo for my chipset and some device so I edit it to my phone specs).
My question is: does .sh files in device tree (vendorsetup.sh, setup-makefiles.sh and extract-files.sh) should be created manually or some other script creates it?
And, also there is 2 .txt files (proprietary-files.txt and proprietary-files-mtk.txt) they contain location of proprietary files, so how do I get that list is it from running vendorsetup.sh, setup-makefiles.sh and extract-files.sh if yes than how do I creates thoose .sh files to do that what should they look like?