Hi Everyone / Anyone,
Got this HTC ONE X+ (64GB) (Not AT&T as only has "HTC" logo on phone) phone from another user who i think spoil the
phone with Cyanogenmod as it keeps reboot and stuck in CYM screen with spining arrows.
Read some posts here and managed to reboot into recovery screen and get some data. It cannot charge properly,
so flash with latest TWRP v2.6.3.0 and now can fully charge to LED turns green.
Some of info of this phone are:
*** UNLOCKED ***
ENRC2B_U PVT SHIP S-ON RL
HBOOT : 1.72.0000
CPLD : None
MICROP : None
RADIO : 3.1204.171.33
eMMC-bootmode : disabled
CPU-bootmode : disabled
HW Secure boot : enabled
MODEM PATH : OFF
Jun 21 2013, 17:36:36
Run fastboot getvar all and some info are:
Version-main : 2.18.707.5
Platform : HBOOT-T30S
Modelid : PM3511000
Cidnum : HTC__044
Battery-status : good
dev-power : 91
partition-layout : None
commitno-bootloader : None
My problem now its seem the HBOOT is very new and not able to find suitable version of 2.18.707.5 image.
Tried run RUU from various sources (WWE, EUROPE,..) cannot flash into the phone. I do not know where
is the reliable ones now and not sure what's next? Have used Hansoon AIO kit and WinDroid, these are helpful
but my phone status does not allow the kit to execute fully.
Now the CYM screen is gone and only show HTC logo screen and cannot proceed to boot further. Of course it
seem the ROM (Custom or stock) are gone as previous user did not make any backup and spoil it.
Summary of what i can do with the phone now:
Reboot phone into recovery mode or Fastboot. Can link PC and phone show FastBoot USB. Can fastboot to phone for lock / unlock.
Observed feedback from TWRP there is no root folder as suggest to install SuperUSR but not sure is it successful.
HELP, Need advice and help to find and load back factory stock ROM or any version suitable for it.
Think it does not have a proper root loaded too.
Installing a custom ROM will be easy
Wipe all excluding the Internal Storage from TWRP
Just "adb push" the ROM file to the SDCARD once the installation is done
boot into fastboot
flash the kernel from the fastboot........
that should get ur phone booted refer to this tutorial for installing a custom ROM
GoRiLaz301 said:
Hi Everyone / Anyone,
Got this HTC ONE X+ (64GB) (Not AT&T as only has "HTC" logo on phone) phone from another user who i think spoil the
phone with Cyanogenmod as it keeps reboot and stuck in CYM screen with spining arrows.
Read some posts here and managed to reboot into recovery screen and get some data. It cannot charge properly,
so flash with latest TWRP v2.6.3.0 and now can fully charge to LED turns green.
Some of info of this phone are:
*** UNLOCKED ***
ENRC2B_U PVT SHIP S-ON RL
HBOOT : 1.72.0000
CPLD : None
MICROP : None
RADIO : 3.1204.171.33
eMMC-bootmode : disabled
CPU-bootmode : disabled
HW Secure boot : enabled
MODEM PATH : OFF
Jun 21 2013, 17:36:36
Run fastboot getvar all and some info are:
Version-main : 2.18.707.5
Platform : HBOOT-T30S
Modelid : PM3511000
Cidnum : HTC__044
Battery-status : good
dev-power : 91
partition-layout : None
commitno-bootloader : None
My problem now its seem the HBOOT is very new and not able to find suitable version of 2.18.707.5 image.
Tried run RUU from various sources (WWE, EUROPE,..) cannot flash into the phone. I do not know where
is the reliable ones now and not sure what's next? Have used Hansoon AIO kit and WinDroid, these are helpful
but my phone status does not allow the kit to execute fully.
Now the CYM screen is gone and only show HTC logo screen and cannot proceed to boot further. Of course it
seem the ROM (Custom or stock) are gone as previous user did not make any backup and spoil it.
Summary of what i can do with the phone now:
Reboot phone into recovery mode or Fastboot. Can link PC and phone show FastBoot USB. Can fastboot to phone for lock / unlock.
Observed feedback from TWRP there is no root folder as suggest to install SuperUSR but not sure is it successful.
HELP, Need advice and help to find and load back factory stock ROM or any version suitable for it.
Think it does not have a proper root loaded too.
Click to expand...
Click to collapse
---------- Post added at 02:55 PM ---------- Previous post was at 02:48 PM ----------
GoRiLaz301 said:
Hi Everyone / Anyone,
Summary of what i can do with the phone now:
Reboot phone into recovery mode or Fastboot. Can link PC and phone show FastBoot USB. Can fastboot to phone for lock / unlock.
Observed feedback from TWRP there is no root folder as suggest to install SuperUSR but not sure is it successful.
HELP, Need advice and help to find and load back factory stock ROM or any version suitable for it.
Think it does not have a proper root loaded too.
Click to expand...
Click to collapse
The Stock Nandroid backup of ur frimware can be found here
To use this u have to put that in the TWRP backups folder which will be a one hectic process to do
Best is to install a custom rom and copy the files to the TWRP folder through MTP......if u want to have Stock ROm
[email protected] said:
Installing a custom ROM will be easy
Wipe all excluding the Internal Storage from TWRP
Just "adb push" the ROM file to the SDCARD once the installation is done
boot into fastboot
flash the kernel from the fastboot........
that should get ur phone booted refer to this tutorial for installing a custom ROM
---------- Post added at 02:55 PM ---------- Previous post was at 02:48 PM ----------
The Stock Nandroid backup of ur frimware can be found here
To use this u have to put that in the TWRP backups folder which will be a one hectic process to do
Best is to install a custom rom and copy the files to the TWRP folder through MTP......if u want to have Stock ROm
Click to expand...
Click to collapse
--------------
in the link regarding "installing a custom ROM" instruction, it seem the phone status permit booting into the phone to "Enable USB Debuggin"
However my case now it will not boot into the normal phone interfaces, it will stuck at "HTC" logo screen and nothing happens afterwards.
I can not only access the Fastboot / Recovery / HBOOT screen of the phone. Any normal reboot will stuck in HTC screen.
also running "adb devices" does not detect the phone and report a serial no. It did run and show opening a port no. 50xx and end successfully.
please advice
i install the Android SDK and followed all instructions carefully but "adb devices" did not return any serial no. of the phone.
in fact the result return blank, nothing is listed.
NOTE the phone can only be connected via USB through recovery mode in Fastboot USB link.
Even when reboot the phone as normal while showing the stucked HTC screen logo, the usb link cannot be established.
please advice.
In CUSTOM Recovery the USB debugging is enabled by default...so that step of booting into phone and enabling the USB debugging doesn't matter...
the device won't get recognized if u had not installed the HTC drivers...
try installing the latest drivers from here
Install this and try
Code:
adb devices
And what are u planning on do install a custom ROM or Flash the Stock Nandroid backup from the thread I provided.....????
I can only help u knowing what u are trying to do.....
GoRiLaz301 said:
--------------
in the link regarding "installing a custom ROM" instruction, it seem the phone status permit booting into the phone to "Enable USB Debuggin"
However my case now it will not boot into the normal phone interfaces, it will stuck at "HTC" logo screen and nothing happens afterwards.
I can not only access the Fastboot / Recovery / HBOOT screen of the phone. Any normal reboot will stuck in HTC screen.
also running "adb devices" does not detect the phone and report a serial no. It did run and show opening a port no. 50xx and end successfully.
please advice
Click to expand...
Click to collapse
GoRiLaz301 said:
i install the Android SDK and followed all instructions carefully but "adb devices" did not return any serial no. of the phone.
in fact the result return blank, nothing is listed.
NOTE the phone can only be connected via USB through recovery mode in Fastboot USB link.
Even when reboot the phone as normal while showing the stucked HTC screen logo, the usb link cannot be established.
please advice.
Click to expand...
Click to collapse
I am trying to get this phone to get to normal functional phone for any region.
Since i got this phone from previous owner, think without any proper ROM backup and got loop in cym logo so am trying to bring this phone "alive" again. It seem not getting anywhere or my procedure is wrong with lack of real ROM in sdcard. At least i managed to figure out somehow get the latest CWM or TWRP and let the phone charge fully. Previously it always show "low battery to flash" message when powered using [ POWER + VOL ] combination.
Not trying to do anything funny to this phone, rather to try my best revive it back to a fully functional phone as the original HTC ONE X+ 64GB International edition. Think this phone is a ASIA WWE edition as it bought locally and with the HTC printed silkscreen, not AT&T.
Sincerely hope u or anyone can help me. I will try to use the "adb device" command again, seem with this way to communicate and push ROM inside the phone, nothing else can get it pass the HTC logo screen now... I am puzzled using Fastboot seem communicating ok with the phone but not adb command.... Keep update....
GoRiLaz301 said:
I am trying to get this phone to get to normal functional phone for any region.
Since i got this phone from previous owner, think without any proper ROM backup and got loop in cym logo so am trying to bring this phone "alive" again. It seem not getting anywhere or my procedure is wrong with lack of real ROM in sdcard. At least i managed to figure out somehow get the latest CWM or TWRP and let the phone charge fully. Previously it always show "low battery to flash" message when powered using [ POWER + VOL ] combination.
Not trying to do anything funny to this phone, rather to try my best revive it back to a fully functional phone as the original HTC ONE X+ 64GB International edition. Think this phone is a ASIA WWE edition as it bought locally and with the HTC printed silkscreen, not AT&T.
Sincerely hope u or anyone can help me. I will try to use the "adb device" command again, seem with this way to communicate and push ROM inside the phone, nothing else can get it pass the HTC logo screen now... I am puzzled using Fastboot seem communicating ok with the phone but not adb command.... Keep update....
Click to expand...
Click to collapse
Fine and clear..
have u tried the drivers I have put in the previous post.........????
Try different USB ports to on ur PC too.......that will work sometimes.......:fingers-crossed:
have install drivers from "installing a custom ROM" page... maybe will try a different USB port after checking and re-install the drivers again.
GoRiLaz301 said:
have install drivers from "installing a custom ROM" page... maybe will try a different USB port after checking and re-install the drivers again.
Click to expand...
Click to collapse
These are the latest HTC drivers can u try this and report whether ur device is recognized in adb recovery mode......
Please try by uninstalling the previous driver u had.........
BTW is it Windows 8.......????????
ok noted but how to uninstall the previous HTC drivers ?
by the way, i also noted that if left the phone to boot after power on, connecting it to PC will be detected but windows cannot install any drivers to it. it will be recognized as HTC MP DEVICE or something similar but with unknown drivers. This normal and ok?
Yesterday feedback in POWER + VOL mode, phone can be recognized as HTC device without USB driver device installation problem.
mine now using Win 7 Home Premium 64-Bit Ed. with latest service packs and updates. Have another PC running Win Vista Biz 32-Bit ed. but not using this one as slower and many software think will affect the phone n PC connection.
Earlier before your help, have found and load TWRP version 2.6.3.0 whereas now the version is 2.4.4.0, will earlier or this 2.4xx version be any difference and affect the connection with adb?
Later will try again the USB drivers and other set up and adb too, not free to do it now...
keep update....
GoRiLaz301 said:
ok noted but how to uninstall the previous HTC drivers ?
by the way, i also noted that if left the phone to boot after power on, connecting it to PC will be detected but windows cannot install any drivers to it.
it will be recognised as HTC MP DEVICE or something similar but will unknown drivers. This normal and ok?
Yesterday feedback in POWER + VOL mode, phone can be recognised as HTC device without USB driver problem.
mine now using Win 7 Home Premium 64-Bit Ed. with latest service packs and updates. Have another PC running Win Vista Biz 32-Bit ed. but not using this one as slower and many software think will affect the phone n PC connection.
Later will try again the USB drivers and other set up and adb too, not free to do it now...
keep update....
Click to expand...
Click to collapse
From the control panel OFC
If u had installed HTC drivers u must be able to see it like this uninstall that...
O Haa haa )
Blunder me ! That's right ! Think bit exhaust after a few sleepless nights figuring out why and hows on this phone....
Now that u mentioned on HTC Driver, before u I have read post on recommended SDK Manager installation.
It is suggested to install SDK Manager with only "Android SDK Platform Tools" + "Google USB Driver" only.
did install these and later use your method to install with "USE AN EXISTING IDE" option of "installer_r22.3-windows.exe" (latest version)
But now did not see the SDK MANAGER program in Control Panel - Programs list... Should have uninstalled.
Think should uninstall the following:
[Windows Mobile Device Center], [Windows Mobile Device Center Driver Update]?
These 2 should be default software of windows or HTC Sync for sync with mobile / usb devices...
Also have installed "Universal Adb Driver" from other post too, think to uninstall this too...
Any recommendation?
GoRiLaz301 said:
Now that u mentioned on HTC Driver, before u I have read post on recommended SDK Manager installation.
It is suggested to install SDK Manager with only "Android SDK Platform Tools" + "Google USB Driver" only.
did install these and later use your method to install with "USE AN EXISTING IDE" option of "installer_r22.3-windows.exe" (latest version)
But now did not see the SDK MANAGER program in Control Panel - Programs list... Should have uninstalled.
Also have installed "Universal Adb Driver" from other post too, think to uninstall this too...
Any recommendation?
Click to expand...
Click to collapse
SDK Manager wont show up on Control panel AFAIK....
it will be a zip file which u have to extract.....
in the extracted folder u will be able to see android-sdk-windows\platform-tools from where u have to open the cmd to execute the abd/fastboot commands
I have the setup of android-sdk-windows and the HTC drivers I pointed to....
It works flawlessly so i recommend to uninstall Universal Adb driver since that isn't helping ur phone recognized anyways.....
Install the Drivers I pointed to and try wether ur phone is getting recognized....:fingers-crossed:
Note : Alternately u can try this installer also which is a small package with the necessary adb and fastboot files......
---------- Post added at 06:43 PM ---------- Previous post was at 06:32 PM ----------
GoRiLaz301 said:
Think should uninstall the following:
[Windows Mobile Device Center], [Windows Mobile Device Center Driver Update]?
These 2 should be default software of windows or HTC Sync for sync with mobile / usb devices...
Also have installed "Universal Adb Driver" from other post too, think to uninstall this too...
Any recommendation?
Click to expand...
Click to collapse
[Windows Mobile Device Center], [Windows Mobile Device Center Driver Update]?
these drivers can be there ...they are or the installation of bluetooth drivers for our phones I guess....
Just uninstall the Universal USB driver .....
If you have HTC Sync I beleive u must be having the HTC driver as I showed on the Screen shot.....
Anyways if u dont see that in the control panel install the one I gave.....U must be fine
ok these r my latest updates:
1) Uninstall HTC SYNC, HTC DRIVER, HTC BMP DRIVER, IPT INSTALLER (Internet Pass-Thru), Universal ADB Driver
2) Install latest Java JRE 7u51 (32 & 64 Bit), Java JDK 7u51 (32 & 64 Bit), detected no older java versions, reboot PC;
3) installer_r22.3-windows.exe (for SDK Manager), created C:\AndroidSDK for SDK Manager and Platform_tools, uninstall default SDK Manager in C:\Program files, Reboot PC;
4) Created Start SDK.bat and run from desktop successfully into directory C:\AndroidSDK\Platform_tools, reboot PC;
5) Install latest HTC Driver using provided link and downloaded with filename HTCDriver_4.10.0.001.msi , reboot PC
Next is to test the USB connection to phone, Q?
1) My phone cannot power on to normal JellyBean OS (as think no ROM);
2) Can only ON to POWER + VOL-DWN mode, to HBOOT > FastBoot, is this right way to test as given in the instruction of http://http://forum.xda-developers.com/showthread.php?t=2213910
2A) If need to let PC detect a working phone and install drivers, have another model [HTC ONE X], can connect USB to this working phone first to test drivers / USB?
Pause here before proceed as concern might spoil the flow of progress if taken wrong step before testing ADB command, please advice.
GoRiLaz301 said:
ok these r my latest updates:
1) Uninstall HTC SYNC, HTC DRIVER, HTC BMP DRIVER, IPT INSTALLER (Internet Pass-Thru), Universal ADB Driver
2) Install latest Java JRE 7u51 (32 & 64 Bit), Java JDK 7u51 (32 & 64 Bit), detected no older java versions, reboot PC;
3) installer_r22.3-windows.exe (for SDK Manager), created C:\AndroidSDK for SDK Manager and Platform_tools, uninstall default SDK Manager in C:\Program files, Reboot PC;
4) Created Start SDK.bat and run from desktop successfully into directory C:\AndroidSDK\Platform_tools, reboot PC;
5) Install latest HTC Driver using provided link and downloaded with filename HTCDriver_4.10.0.001.msi , reboot PC
Next is to test the USB connection to phone, Q?
1) My phone cannot power on to normal JellyBean OS (as think no ROM);
2) Can only ON to POWER + VOL-DWN mode, to HBOOT > FastBoot, is this right way to test as given in the instruction of http://http://forum.xda-developers.com/showthread.php?t=2213910
2A) If need to let PC detect a working phone and install drivers, have another model [HTC ONE X], can connect USB to this working phone first to test drivers / USB?
Pause here before proceed as concern might spoil the flow of progress if taken wrong step before testing ADB command, please advice.
Click to expand...
Click to collapse
FIne....
From bootloader boot into recovery.....
try whether u r device is recognized.......
If recognized PROFIT for the hectic work done......
then u can push a rom to ur SDCARD using adb push command......
then install as usual from the recovery........
ok, this is what the usb detected after boot into Recovery (TWRP screen) and captured a screen shot,
is it ok?
JACK POT !!!!
ADB DEVICES listed my device s/n. in recovery mode.!
GoRiLaz301 said:
ok, this is what the usb detected after boot into Recovery (TWRP screen) and captured a screen shot,
is it ok?
Click to expand...
Click to collapse
Absolutely Fine........
What I meant in While in TWRP connect ur phone to PC
double click on your Start SDK shortcut and in the CMD type
Code:
adb devices
Ur result must be like this
YES, it did show the device listed with serial no.
Now i into the [Recovery Installation] section and at the BACKUP part (pt. 15), now should i also tick Recovery + Cache to perform full backup of actual ROM? (this seem not applicable to me, is it?)
Related
Okay so I'm new to Android. I have been trying to update to a new rom but have pretty much got stuck at the first hurdle. I have been trying to follow http://forum.xda-developers.com/showthread.php?t=552591
MoDaCo Custom ROM is here (2 versions based on the 'new update')!
As stated in the first thing to do for a newbie is to Download the patched recovery image linked above and install as detailed in that post.
I have not been able to get pasted this stage
Please please please can someone write an idiots guide for this as by the end of tonight I’m going to be bald as I’m pulling my hair out.
robboy said:
Okay so I'm new to Android. I have been trying to update to a new rom but have pretty much got stuck at the first hurdle. I have been trying to follow http://forum.xda-developers.com/showthread.php?t=552591
MoDaCo Custom ROM is here (2 versions based on the 'new update')!
As stated in the first thing to do for a newbie is to Download the patched recovery image linked above and install as detailed in that post.
I have not been able to get pasted this stage
Please please please can someone write an idiots guide for this as by the end of tonight I’m going to be bald as I’m pulling my hair out.
Click to expand...
Click to collapse
1. make a full nandroid backup
2.download the recovery image
3.turn off your phone and turn on by pressing the on button+the back key (to get into bootloader)
4.open a terminal from the folder which contains the recovery image.
5. type 'fastboot boot cm-hero-recovery.img'
6.type 'adb shell mount /sdcard'
7.type 'adb push cm-hero-recovery.img /sdcard/cm-hero-recovery.img'
8.type 'adb shell flash_image recovery /sdcard/cm-hero-recovery.img'
now whenever you want to access the recovery console, you just have to switch your phone on+home key and u'll enter.
To install the rom,
9. download the radio and rom from modaco
10. plug in ur usb and mount sd card
11. copy radio into sd card and rename to update.zip.
12. switch off phone and enter recovery console
13.if you never upgraded the phn , then a wipe is necessary
14. then, select update.zip..
15. u repeat the steps from step9 onwards the same way to update the rom.
hope ie helped.
i mentioned nandroid backup as from step 1 itself.
just came to realise that maybe u have never accessed recovery image from pc.
well dont worry, u can ignore step one but be sure to make the backup after step 8 ..... before installing the new rom
cheers and good luck
Okay so number 4 is my problem. Do o do this from the phone or pc?
robboy said:
Okay so number 4 is my problem. Do o do this from the phone or pc?
Click to expand...
Click to collapse
From the pc. A DOS terminal, if you are on windows.
should I allready have partitioned my sd card before i do this?
This is the error message i get
robboy said:
This is the error message i get
Click to expand...
Click to collapse
As far as I can see, you opened the command-line in the system32 dir from youre PC?! You should open the commandline in the dir where the image-file is. Should look like C:\SDK\tools
See this post to guide you further.
http://forum.xda-developers.com/showpost.php?p=4257045&postcount=38
robboy said:
This is the error message i get
Click to expand...
Click to collapse
To open a terminal( command prompt) from a folder,
1.go to accesories in Windows, copy the command prompt.
2. Go to your folder and paste it there.
3.right click on the command prompt, go on prope
rties.
4. U will find a line containing ' start in : %homedrive%%homepath....'
5. Delete that line so that 'start in' remains blank
6. Apply. And u r good to go
By the way. I supposed u already installed HTC sync right.
okay I thought HTC sync might be causing me problems so i removed it
robboy said:
okay I thought HTC sync might be causing me problems so i removed it
Click to expand...
Click to collapse
You will need to install HTC sync cause it contains the drivers for you phone.
Okay so I have put HTC sync back on. My hero connects to the sync in normal mode as an android USB devices - My HTC . What I'm unsure of now is when I press 'on and back buttons to go into bootloader' should the hero still sync as My HTC or should it be syncing to a different driver. I have been going round in circles all day. I have also removed the android development software as before the hero was syncing as and adb device??
When going to the cdm I now get the error device not found. USB debugging is selected on my device.
I think I’m on the brink of giving up.
okay so now when I'm in the bootloader my device connects as a ADB Interface - HTC Bootloader.
BTW I'm on Vista and i selected the driver that was in x86 folder that I was advised to download. However still no device found
robboy said:
Okay so I have put HTC sync back on. My hero connects to the sync in normal mode as an android USB devices - My HTC . What I'm unsure of now is when I press 'on and back buttons to go into bootloader' should the hero still sync as My HTC or should it be syncing to a different driver. I have been going round in circles all day. I have also removed the android development software as before the hero was syncing as and adb device??
When going to the cdm I now get the error device not found. USB debugging is selected on my device.
I think I’m on the brink of giving up.
Click to expand...
Click to collapse
Yes if your device is recognised as adb ... it's good.
That's how it should be.
Try installing HTC sync before plugging ur phone, then enter bootloader on the phn, plug it in, and then perform the command from the prompt.
P.s try entering bootloader first and only afterwards u plug in ur phone
Try to get the latest driver HTC sync from HTC site. If that doesnt work, try downloading the latest sdk plus drivers. U can find it somewhere on the forum . I think that there is a link on the rooting guide by daysee
I'm a total noob at Android too but theunlockr.com was the easiest and fastest way for me to install the custom Modacco ROM. Check out their site; it'll show you step by step with videos :]
Hi,
the last days, I read a lot about flashing custom ROMs and wanted to do so with my HTC Legend. I'm not really new to flashing ROMs in general.I already flashed several other devices, but I'm stuck with unlocking the bootloader. My problem is, that the CMD is either reacting with "CommandError" or "waiting for device". I'm not able to get the token for unlocking the bootloader. Another problem is, that the SDK Manager won't start for me. So I just grabbed the 3 files out of the filesystem and tried it with them. Using HTCs recommended fastboot.exe doesn't change anything. I hope you can help me with a few details:
1. Do I have to install something else than HTC Sync? (I think, it already installed the driver, too)
2. Which connection mode should i choose, when connecting the legend? (recharging/hdd/htc sync/tethering)
3. Which version of the SDK should I use? Is it possible, that someone just gives me a zip with those 3 files?
I'm looking forward to your answers!
Regards
OdlG
SOLUTION:
The solution was a too old version. My phone had version 3.15.405.3.
First I updated to version 3.15.405.6 (found via google here at xda-dev).
Then I patched the new ROM I downloaded from htc-dev (step 0 at unlocking; must connect phone for that hint!) 3.30.0.0.
Then I could receive the token via CMD at a Windows 7 PC (Win8 PC still said "waiting for device", obviously because the driver wasn't installed correctly so the phone wasn't recognised in fastboot mode).
I followed the last steps rom htc-dev and now unlocked the bootloader
Click to expand...
Click to collapse
(pardon my english, it's not my mothertongue)
AW: Difficulties with unlocking the Bootloader
You should use charging mode and you have to activate usb debugging in settings
Sent from my HTC One using xda app-developers app
Thanks for the reply!
I already enbled USB Debugging, and now tried it in charging mode. I created a BAT-File with the following command:
cd C:\Android\
fastboot oem get_identifier_token
But it still says "waiting for device" Any suggestions?
Did you follow these instructions? especcially selecting "fastboot"?
http://www.htcdev.com/bootloader/unlock-instructions
if yes and it still didn't work i've no idea at the moment
I tried it once more:
I connected the phone, "fastboot usb" is written there. the cmd still writes "waiting for device". after a few seconds, the pc reports, that the usb device could not be recognised. then there is written "fastboot" instead of "fastboot usb", though the cable is still connected.
a few hours ago i also got a guide at htc dev, that i should install da RUU (what does it mean btw?). i downloaded the german vodafone version and tried to install it. I will try that once more, hopefully the unlock will be successful afterwards!
thanks for your advice!
EDIT:I'm using the following software btw.
Android SDK (adt-bundle-windows-x86_64-20130219)
Java RE 7 Update 17
HTC Sync (3.3.X or something like that)
The RUU installer is starting the setup without problems. It's rebooting the phone o install version 3.30 (hboot1.02). But when the Phone starts in the bootloader mode and displays "RUU", the PC is unable to detect the USB device and the setup fails caused by missing usb connection
Can I somehow influence the detection of the phone in fastboot/bootloader mode?
Normally it should be enough to install the HTC USB Drivers...
You can grab the newest for example from this thread: http://forum.xda-developers.com/showthread.php?t=2191279
The second what you need is an actual adb.exe, fastboot.exe, AdbWinApi.dll & AdbWinUsbApi.dll... grab it for example from here: http://d-h.st/RvD (Thanx to torxx (http://forum.xda-developers.com/member.php?u=3828647))
After u've installed the drivers and extracted the adb file do the folowing
Turn off your phone completly
Push Vol down & Power ...device will start
Navigate with vol+- to fastboot press power
connect with usb-cable (possible that windows will install drivers...wait till its complete)
now "fastboot usb" should be read in the display of your phone
open a shell (cmd)
navigate to your fastboot.exe
type: "fastboot oem get_identifier_token"
it seems, that my htc firmware is far too old (3.15.405.3). i installed all the stuff on my win7 laptop instead of win8 desktop pc and could install the RUU... at least untill the notification, that i needed to update the firmware first, and update hboot1.02 (3.30.0.0) afterwards. the big update is also 150MB, the small one only 5MB. i'll give it a try and report back here, if i am able to manage all the stuff^^
btw autoupdating via options doesn't work ("phone is up to date"). do i have to sign in via google to get a better result?
I managed to unlock the bootloader!
The solution was a too old version. My phone had version 3.15.405.3.
First I updated to version 3.15.405.6 (found via google here at xda-dev).
Then I patched the new ROM I downloaded from htc-dev (step 0 at unlocking; must connect phone for that hint!) 3.30.0.0.
Then I could receive the token via CMD at a Windows 7 PC (Win8 PC still said "waiting for device", obviously because the driver wasn't installed correctly so the phone wasn't recognised in fastboot mode).
I followed the last steps rom htc-dev and now unlocked the bootloader
now i will try the rest Thanks for the helpful hints!
AW: [solved] Difficulties with unlocking the Bootloader
Okay nice to hear that it now works:thumbup:
I would say... Have fun while flashing and trying new roms
Sent from my HTC One using xda app-developers app
esco27 said:
Okay nice to hear that it now works:thumbup:
I would say... Have fun while flashing and trying new roms
Sent from my HTC One using xda app-developers app
Click to expand...
Click to collapse
Already flashed CM10.1 It's not as smooth as on my Ainol Aurora 2 Tablet, but the Legend hasn't got the power by far. But if you have a look at the specs, it is amazing, how good it runs on the legend
Thanks for all the help! That was definately worth it^^ I only have minor problems with my SIM-card up to now.
`Dear Admin,
Hi my Name is Zaki.... i am using HTC Rezound which i purchased in U.A.E
After installing whatsapp i got continious restart problem so i downloaded stock firmware of ICS version. all was good but by mistake i clear internal storage in fastboot mode. and after that i am unable to get into TWRP Recovery mode, it is showing phone with with arrow circle and after few second it converted into phone with triangle (attached screens 2 and 3) please explain me with links how to get TWRP again. and the links for TWRP versions i am not sure which is ok.
Please Reply.
syedzakiabidi said:
`Dear Admin,
Hi my Name is Zaki.... i am using HTC Rezound which i purchased in U.A.E
After installing whatsapp i got continious restart problem so i downloaded stock firmware of ICS version. all was good but by mistake i clear internal storage in fastboot mode. and after that i am unable to get into TWRP Recovery mode, it is showing phone with with arrow circle and after few second it converted into phone with triangle (attached screens 2 and 3) please explain me with links how to get TWRP again. and the links for TWRP versions i am not sure which is ok.
Please Reply.
Click to expand...
Click to collapse
You can't access TWRP because you over-wrote it with the factory RUU firmware image, it isn't there anymore...
Download TWRP image from TWRP official site at https://dl.twrp.me/vigor/ or Flyhalf's build at http://forum.xda-developers.com/showthread.php?t=1902381
Either one is good... then start fastboot, connect usb and flash recovery with the command:
fastboot flash recovery <path/filename of TWRP IMG file>
give it a minute or so, reboot into Hboot and start TWRP.
im having a similar issue but my computer always says waiting for device in command prompt. I have all the drivers installed and the phone says "usb fastboot" or "fastboot usb" (cant recall what order those 2 words are in LoL)
youdoofus said:
im having a similar issue but my computer always says waiting for device in command prompt. I have all the drivers installed and the phone says "usb fastboot" or "fastboot usb" (cant recall what order those 2 words are in LoL)
Click to expand...
Click to collapse
You probably have a driver issue then... Install HTC Sync, connect the phone, then disconnect it, remove HTC Sync and it should work. If that doesn't work, try a different USB port.
Honestly, I switched to Linux a long time ago... I don't have driver issues. If you were running Linux, even a live or USB key distro, you would access it easily.
acejavelin said:
You probably have a driver issue then... Install HTC Sync, connect the phone, then disconnect it, remove HTC Sync and it should work. If that doesn't work, try a different USB port.
Honestly, I switched to Linux a long time ago... I don't have driver issues. If you were running Linux, even a live or USB key distro, you would access it easily.
Click to expand...
Click to collapse
fair point, and i do have ubuntu (of differing flavor dates) on 3 of my machines, so i might just do that. Thanks!! Ill also try the goofy htcsynch (which i forgot about, as im a Sammy guy now) Thanks again!!
Hello,
I have htc desire 601 and android operating system crash and i am unable to boot in the system and enable usb debugging. My phone stops in htc logo. I tried to boot in recovery mode but it dont work and when i tried to root another rom i cant because USB Debugging is off... Has anyone solution for that kind off problem, please?????
sinkowc91 said:
Hello,
I have htc desire 601 and android operating system crash and i am unable to boot in the system and enable usb debugging. My phone stops in htc logo. I tried to boot in recovery mode but it dont work and when i tried to root another rom i cant because USB Debugging is off... Has anyone solution for that kind off problem, please?????
Click to expand...
Click to collapse
U can boot into Hboot right??
If so then go to fastboot mode from there & flash Recovery
If that's not the option for u then i think ruu(rom upgrade utility by htc dev )is solution for u...
yes i can do that to go in hboot mode and i downloaded that ruu file and cannot do that because pc doesnt find my phone and i have installed drivers. Everywhere it says that USB debugging must be enable to do that. I have also downloaded sdk manager and platform tools to try install ruu with cmd via usb cabel but device was not found also. I tried many ways that is on youtube and xda forums but there isnt any good solution yet for me. For good solution that work il gave some donation.
Flash Recovey via fastboot If Device Stuck or Crashed
sinkowc91 said:
yes i can do that to go in hboot mode and i downloaded that ruu file and cannot do that because pc doesnt find my phone and i have installed drivers. Everywhere it says that USB debugging must be enable to do that. I have also downloaded sdk manager and platform tools to try install ruu with cmd via usb cabel but device was not found also. I tried many ways that is on youtube and xda forums but there isnt any good solution yet for me. For good solution that work il gave some donation.
Click to expand...
Click to collapse
Requirements---
1)twrp recovery https://dl.twrp.me/zara/
a)if ur's is zara ul then go for https://dl.twrp.me/zara/twrp-2.8.7.0-zara.img.html
b)if it's zara cl then go for https://dl.twrp.me/zara/twrp-2.8.7.0-zaracl.img.html
2)fastboot cmd 'fastboot flash recovery recoveryname.img' ------------> Where Recovery Name is the file name of ur recovery
3)Any Custom Rom Or Stock Zip
Procedure
1)boot into hboot
2)click on fastboot and connect usb cable
3)open cmd and check fastboot devices
4)it show some id with fastboot name [if it is then u r good]
5)now copy the recovery in ur current cmd folder or else change the folder of cmd into ur recovery path
6)now type fastboot flash recovery twrp-2.8.7.0-zara.img
7)now click on boot loader and scroll down to recovery then click on it
8)now ur in recovery mode now flash any custom rom's [i suggest resurection remix]
9)Before Flasing do factory reset in wipe section and go for install zip in install section
10)now ur good to boot
Note
1)to copy zip to sdcard/ext-card our twrp recovery supports mtp enable while on recovery mode[open my computer there u can see mtp device]
2)if u want to process ruu only then click on adb sideload in advanced sections i think adb will detect the device as in recovery mode
3)then open ruu [i might think it will work]
3)i did nt test the above process
4)if u want the stock os only then download required stock zip and flash it...there r many stocks like europe,,asia .................................
5) Hope u Installed Sdk Manger If not so go for MINIMAL ADB AND FASTBOOT.EXE
At the Same Time U Better Take a look on this Thread Also http://forum.xda-developers.com/desire-601/general/collection-kitkat-ruu-t3228817
Hope it might Helps
Thanks to XDA Developers Thanks To TWRP Recovery Thanks to Custom Roms
And Finally Thanks To My frnd Hareesh
Hi !
I've attempted to deal with the devil by trying to root my Pioneer XDP-300R resulting in a bootloop problem (device is stuck on "Powered by Android" screen).
I attempted to flash a boot.img for a Onkyo DX-P1 (which is the same firmware), and still I haven't progressed.
No firmware, update or imgs are provided on Pioneer's website.
I still have access to fastboot (OEM is LOCKED, so I can't boot TWRP and such) in bootloader mode and adb push (no shell) in recovery mode.
Do you guys have any idea how to sort it out ?
Edit :
I managed to make my device go into Qualcomm's emergency download mode.
Here's how to :
1 - Make sure the device is completely off and unplugged from USB.
2 - Install QPST V2.7.474 (not enough posts to share url, but I can PM it).
3 - Install QDLoader Drivers (same as #2).
4 - Simply press and hold the "Play" button while connecting it to your computer, the device manager should see a "Qualcomm 9008 port" listed in Ports while the player's screen stays black.
5 - Do the Carlton (important step !)
Now, if anyone possessing a FUNCTIONAL AND ROOTED Pioneer XDP-300r is reading this and willing to help, can you get in touch with me ?
Together, we could manage to save all the other devices from soft-bricking.
All I would need from you is some time, hard disk space and patience to sort it out.
Please <insert_your_name_here>, you're my only hope !
Edit #2 :
Thanks to minotauri's great help, we managed to get a FULL rom backup, split the partitions to files and generate all the files needed for QFIL.
ErrOzz has been given access to this, hoping that he'll try it out soon.
If that works, I'll link you the files and write the walkthrough to bring you DAP back to life.
minotauri's contributions are not in rest tho, he managed to also successfuly patch TWRP for the device, so anyone can securely flash things from there now.
For anyone reading this thread : you're not the only one who screwed things up, we did too but we might have the cure. Hang in there !
grogcw said:
Hi !
I've attempted to deal with the devil by trying to root my Pioneer XDP-300R resulting in a bootloop problem (device is stuck on "Powered by Android" screen).
I attempted to flash a boot.img for a Onkyo DX-P1 (which is the same firmware), and still I haven't progressed.
No firmware, update or imgs are provided on Pioneer's website.
I still have access to fastboot (OEM is LOCKED, so I can't boot TWRP and such) in bootloader mode and adb push (no shell) in recovery mode.
Do you guys have any idea how to sort it out ?
Edit :
I managed to make my device go into Qualcomm's emergency download mode.
Here's how to :
1 - Make sure the device is completely off and unplugged from USB.
2 - Install QPST V2.7.474 (not enough posts to share url, but I can PM it).
3 - Install QDLoader Drivers (same as #2).
4 - Simply press and hold the "Play" button while connecting it to your computer, the device manager should see a "Qualcomm 9008 port" listed in Ports while the player's screen stays black.
5 - Do the Carlton (important step !)
Now, if anyone possessing a FUNCTIONAL AND ROOTED Pioneer XDP-300r is reading this and willing to help, can you get in touch with me ?
Together, we could manage to save all the other devices from soft-bricking.
All I would need from you is some time, hard disk space and patience to sort it out.
Please <insert_your_name_here>, you're my only hope !
Click to expand...
Click to collapse
Hi - I saw your post on Head-Fi (antdroid over there). Let me look into this!
Here is a bunch of system dump images and qcn files: https://drive.google.com/drive/folders/1diqQ8LE-yG4b-WZFB_OPcQp2rDUp9BbV?usp=drive_open
Hello.
How can I write boot from qdload 9008 state?
Hi !
From the edl / qdload 9008 state, you can't afaik.
Here's how I think you can :
1 - Unplug your device from USB and power it off from whatever state it is.
2 - Power it on pressing Power + Previous button (keep holding, you should be "stuck" on the penguin logo).
3 - Connect your USB.
4 - Check that you have a Android ADB Device in your device manager (install drivers manually if you have an Unknown device).
5 - Grab any fastboot from the internet if you don't already have it (I'll PM you my gdrive, it's there for exemple).
6 - From CMD, go to fastboot directory. (cd <my_folder_with_fastboot>).
7 - Type in : fastboot devices
If fastboot sees your device, you're on the good path, else, check your driver / connection / reboot to fastboot "penguin" state.
8 - Type in : fastboot oem device-info
If it replies
(bootloader) Device unlocked: true
among others, you're in a good, good way, else, you're screwed by now, but we are working on it.
9 - If all the precedent are fulfilled type :
fastboot flash boot <my_boot_image.img>
10 - Mandatory Carlton.
I hope you'll be in the right path all the way, if you're stuck somewhere or if your bootloader is locked, please let me know.
Cheers !
ErrOzz said:
Hello.
How can I write boot from qdload 9008 state?
Click to expand...
Click to collapse
I was successful in creating a recovery (twrp) for this device.
https://www.antdroid.net/2019/02/pioneer-xdp-300r-root-twrp-recovery.html?m=1
also created a XDA thread here: https://forum.xda-developers.com/android/development/pioneer-xdp-300r-digital-audio-player-t3902949
Feel free to PM me if you have questions or we can work it through here
Hi,
I have the same problem. I am able to get qdload 9008 state from here now. However, after unplug and followed grogcw's hints, the device is not recognized again. Also, the device hasn't ennobled debug mode before too. All the adb and fastboot commands return no device.
Hopefully can get more help here.
---------- Post added 28th February 2019 at 12:16 AM ---------- Previous post was 27th February 2019 at 11:58 PM ----------
minotauri said:
I was successful in creating a recovery (twrp) for this device.
https://www.antdroid.net/2019/02/pioneer-xdp-300r-root-twrp-recovery.html?m=1
also created a XDA thread here: https://forum.xda-developers.com/android/development/pioneer-xdp-300r-digital-audio-player-t3902949
Feel free to PM me if you have questions or we can work it through here
Click to expand...
Click to collapse
Is there anyway to flash TWRP and so with QDLoader?
I believe he is on vacation for another week and half. If you haven't enabled the bootloader unlock option within Android, then my recovery method may not work since it may not let you flash the recovery.
You can try to fastboot boot recovery.img though
Hi ! I'm back from vacation, but I still haven't my device around.
Any user willing to test are welcome to reply or PM me !
Let's have all the bricked units working, shall we
grogcw said:
Hi ! I'm back from vacation, but I still haven't my device around.
Any user willing to test are welcome to reply or PM me !
Let's have all the bricked units working, shall we
Click to expand...
Click to collapse
How can we get started?
We actually did start probing stuff around, and we are missing something in the "full restoration process", so we're stuck for now.
Sahara protocol still is a mystery for us, and we can't get pass an error.
I think we don't actually have the right programmer_firehose.mbn for our device, but if it's not this, I'm basically out of ideas. (we might need an "QFIL expert" on this)
I still don't have my device around and feeling dumb about this.
Anyway, all the files and tools required to try probing around are in my gdrive and I can PM the link (as I still can't post it right away) if anyone is interested.
Thanks for trying to help or actually help everyone !
Cheers !
Hello,
I try to root my xdp-300r,after reboot have bootloop result.
I don't know how to reflash systme.img.
can suggest any repair plan,thank you~
Was able to unbrick device. Here are the steps TO DO IT
grogcw said:
hi !
I've attempted to deal with the devil by trying to root my pioneer xdp-300r resulting in a bootloop problem (device is stuck on "powered by android" screen).
I attempted to flash a boot.img for a onkyo dx-p1 (which is the same firmware), and still i haven't progressed.
No firmware, update or imgs are provided on pioneer's website.
I still have access to fastboot (oem is locked, so i can't boot twrp and such) in bootloader mode and adb push (no shell) in recovery mode.
Do you guys have any idea how to sort it out ?
edit :
i managed to make my device go into qualcomm's emergency download mode.
Here's how to :
1 - make sure the device is completely off and unplugged from usb.
2 - install qpst v2.7.474 (not enough posts to share url, but i can pm it).
3 - install qdloader drivers (same as #2).
4 - simply press and hold the "play" button while connecting it to your computer, the device manager should see a "qualcomm 9008 port" listed in ports while the player's screen stays black.
5 - do the carlton (important step !)
now, if anyone possessing a functional and rooted pioneer xdp-300r is reading this and willing to help, can you get in touch with me ?
Together, we could manage to save all the other devices from soft-bricking.
All i would need from you is some time, hard disk space and patience to sort it out.
please <insert_your_name_here>, you're my only hope !
edit #2 :
thanks to minotauri's great help, we managed to get a full rom backup, split the partitions to files and generate all the files needed for qfil.
Errozz has been given access to this, hoping that he'll try it out soon.
If that works, i'll link you the files and write the walkthrough to bring you dap back to life.
Minotauri's contributions are not in rest tho, he managed to also successfuly patch twrp for the device, so anyone can securely flash things from there now.
For anyone reading this thread : You're not the only one who screwed things up, we did too but we might have the cure. Hang in there !
Click to expand...
Click to collapse
i was able to unbrick my device
dantuko said:
all credits go to anthony nguyen aka minotauri. Thank you!
requirements:
samsung drivers installed
windows 10 (i have the windows 10 pro installed)
oem unlock
usb debbuging selected prior to brick
install the latest samsung drivers
install fastboot/adb drivers
stock-boot.img provided by minotauri
the steps are as follows:
the device must be in recovery mode an plugged to the computer. I was on stock recovery
open device manager in windows, look for anything android and delete it and choose to delete the drivers
refresh device manager for new devices (keep only the xdp-300 android connected)
right click on the android device and click on update drivers
select browse my computer for driver software
click on let me pick from a list of available drivers
unselect show compatible drivers (if you see a samsumg driver here, select it. If not try generic windows adb drivers)
seletct google adb drivers (this is the one that worked and it's under samsung drivers)
i performed the steps 1 through 8 a few times until the computer categorized the device as adb
open a command prompt, navigate to the directory where fastboot is installed and type: Fastboot devices (you should have a device listed here)
type: Fastboot oem unlock (this unlocks the bootloader)
after copying stock-boot.img to the root of the your fastboot directory, type: Fastboot flash boot stock-boot.img (reboot)
after the reboot you should see normal boot
if you want twrp and root follow the instructions here: https://forum.xda-developers.com/android/development/pioneer-xdp-300r-digital-audio-player-t3902949 all credits go to anthony nguyen.
i installed twrp the latest supersu pro, viper4android, root browser, busy box pro and everything works perfectly.
:fingers-crossed::fingers-crossed::fingers-crossed:good luck to you e n j o y ! ! !:fingers-crossed::fingers-crossed::fingers-crossed:
i am not an android programmer so i won't be able to help you from that perspective, but i a software engineer so i maybe able to answer some questions.
There is no guarantee this method will work for you but it did work for me
I can provide a TWRP backup file for you to restore your device
Click to expand...
Click to collapse
I have a rooted xdp300r rooted
ralf05 said:
Hello,
I try to root my xdp-300r,after reboot have bootloop result.
I don't know how to reflash systme.img.
can suggest any repair plan,thank you~
Click to expand...
Click to collapse
It was bricked and I was able to fix it and root it
Help !!!
Hello
Gentlemen, help me! I've broken my device
I hit the whole system on my xdp300r. What can I do in this case ??? Only I can turn on TWRP and nothing more.
[email protected]
---------- Post added at 05:55 PM ---------- Previous post was at 05:51 PM ----------
dantuko said:
i was able to unbrick my device
Click to expand...
Click to collapse
Help !!!
dantuko said:
i was able to unbrick my device
Click to expand...
Click to collapse
Hello
Could I ask you for a backup file? Unfortunately, I lost the systemThank you very much.
Greetings.
[email protected]
stefan999 said:
Hello
Could I ask you for a backup file? Unfortunately, I lost the systemThank you very much.
Greetings.
[email protected]
Click to expand...
Click to collapse
I UPLOADED THE BACKUP FILE TO MY GOOGLE DRIVE
https://drive.google.com/drive/folders/1vM7Z12w3CsbutSr54lY4tTdzyN1jurpp?usp=sharing
dantuko said:
I UPLOADED THE BACKUP FILE TO MY GOOGLE DRIVE
https://drive.google.com/drive/folders/1vM7Z12w3CsbutSr54lY4tTdzyN1jurpp?usp=sharing
Click to expand...
Click to collapse
Here is a few items to note about the image:
You must have twrp installed and accessible in order to restore this image.
First time booting after the restore will take a long time, so have a cup of coffee and let it do it's thing.
Every time you boot the OS will perform application optimization, it doesn't bother me so I have not even looked into it.
After you boot connect to your WIFI and open Google Play to set up your account
If you want to use Viper4Android, download and install busybox, then open settings, go to apps and disable Musicfx, then reboot and turn Viper4Android on.
Good luck
dantuko said:
Here is a few items to note about the image:
You must have twrp installed and accessible in order to restore this image.
First time booting after the restore will take a long time, so have a cup of coffee and let it do it's thing.
Every time you boot the OS will perform application optimization, it doesn't bother me so I have not even looked into it.
After you boot connect to your WIFI and open Google Play to set up your account
If you want to use Viper4Android, download and install busybox, then open settings, go to apps and disable Musicfx, then reboot and turn Viper4Android on.
Good luck
Click to expand...
Click to collapse
Thanks for answer and sharing your files. Unfortunately, there is some error when trying to restore in TWRP.
I packed all the items from your disk in ZIP and downloaded to the SD card .
I'm getting an error about the content: no MD5 file found Failed to map file'/external_sdxxxxxx-Full BACKUP.zip'
Error instaling zip file
. Do you have an idea why this is happening?
twrp settings
stefan999 said:
Thanks for answer and sharing your files. Unfortunately, there is some error when trying to restore in TWRP.
I packed all the items from your disk in ZIP and downloaded to the SD card .
I'm getting an error about the content: no MD5 file found Failed to map file'/external_sdxxxxxx-Full BACKUP.zip'
Error instaling zip file
. Do you have an idea why this is happening?
Click to expand...
Click to collapse
You need to change settings in twrp not to check md5 checksum, if it doesn't work then i'll create one with checksum.