Related
hey guys, been here since the launch of evo. rooting, flashing, everything.
today i wanted to switch roms. so i went about my normal process...
d/l new ROM
backup current ROM
backup apps
wipe cache and dalvic
flash new ROM
i got stuck on the last step. i went to flash the new ROM (nocturnal 1.3)
it said something along the lines of blah blah is already unmounted. i didnt pay too much attention to it because i was going to restart and try again. long story short, it will only boot to htc white screen and nothing else.
can anyone help me out?
p.s. im on clockwork recovery
PLEASE CLOSE
did you not wipe system and data? I am not super skilled, but maybe it tried to stick the entire ROM into the left over space of the last ROM that is still on there?
It won't boot to recovery? It should boot to recovery
weezymagic said:
hey guys, been here since the launch of evo. rooting, flashing, everything.
today i wanted to switch roms. so i went about my normal process...
d/l new ROM
backup current ROM
backup apps
wipe cache and dalvic
flash new ROM
i got stuck on the last step. i went to flash the new ROM (nocturnal 1.3)
it said something along the lines of blah blah is already unmounted. i didnt pay too much attention to it because i was going to restart and try again. long story short, it will only boot to htc white screen and nothing else.
can anyone help me out?
p.s. im on clockwork recovery
Click to expand...
Click to collapse
The error message you received is going to be the key to understanding the issue that occured. When it says unmounted, it is referring to a specific partition, either /data or /system most likely.
For starters, when it hangs on the htc white screen, this is usually either a kernel or ramdisk issue. If the kernel is known to be good, then it is probably a ramdisk issue. most ramdisk issues relate to a mismatch/incompatibility between the loaded kernel and the ROM.
First suggestion would be to reflash the ROM, clearing /cache and /data.
Second suggestion would be to restore a backup. This will confirm there is nothing wrong with your device hardware wise and you'll know it is a specific issue with the ROM you wanted to load.
Third suggestion, find the exact error, word for word, which occured in recovery and post up in the ROM thread asking if other users of that ROM also encountered, how they handled. Also feel free to post back up here.
When writing the programming behind a custom recovery, the error messages are added in there to help allow users and developers better knowledge of the exact issue so they can work to resolve them. Without the exact error message, it is similar to going to a car shop and saying, some light came on my dash, but I don't know what it was and now the car doesn't work. Fix it? Another words, it is very vague.
Hope the suggestions and tips help! Good luck!
my first instinct was to reflash the backup or new rom again but it wont boot to any rom, recovery or bootloader. it just hangs on the htc white screen
idk what happened but i got into the bootloader through battery pull, power+vol down. i know ive tried that in the past but this time it worked. now im restoring a nandroid from yesterday
weezymagic said:
idk what happened but i got into the bootloader through battery pull, power+vol down. i know ive tried that in the past but this time it worked. now im restoring a nandroid from yesterday
Click to expand...
Click to collapse
are you on twrp 1.0.x ? There is s charging issue where it won't restart right because it thinks It's already in recovery
sent from my EVO 3D via XDA app
weezymagic said:
hey guys, been here since the launch of evo. rooting, flashing, everything.
today i wanted to switch roms. so i went about my normal process...
d/l new ROM
backup current ROM
backup apps
wipe cache and dalvic
flash new ROM
i got stuck on the last step. i went to flash the new ROM (nocturnal 1.3)
it said something along the lines of blah blah is already unmounted. i didnt pay too much attention to it because i was going to restart and try again. long story short, it will only boot to htc white screen and nothing else.
can anyone help me out?
p.s. im on clockwork recovery
PLEASE CLOSE
Click to expand...
Click to collapse
You missed a step. After you wipe dalvik and cache, you ALWAYS need to wipe /system and /data, do a factory reset to make sure, or download a superwipe tool. The ONLY time you don't need to wipe completely is when you're updating your ROM, but even then it is recommended to wipe everything.
Twolazyg said:
You missed a step. After you wipe dalvik and cache, you ALWAYS need to wipe /system and /data, do a factory reset to make sure, or download a superwipe tool. The ONLY time you don't need to wipe completely is when you're updating your ROM, but even then it is recommended to wipe everything.
Click to expand...
Click to collapse
Agreed^^^^^
OK so let me start off with, great site. I have read a ton of information.
First: Siyah 4.3.3 (Latest) Kernel which now has been put to AJK v1.48s
ROM; SHOstock3 v2.5.9
PreMod Settings: SGS2 AT&T SGH-i777. Started with GB > AT&T OTA (KIES) 4.0.3 > AT&T OTA WIFI 4.0.4 (caused huge freaking headaches with battery, charging, turn off the phone loop, battery draining, etc.)
Issues:
Original Issue posted in this thread (viewing Single Post) http://forum.xda-developers.com/showpost.php?p=39350619&postcount=18
Creepy offered something to try. That never worked as all I was able to do was download mode or stare at the Samsung Galaxy S2 Splash Screen. Well, I took to his download repository and other links and used his One-Click Recovery to stock GB Rom to make part of my phone usable, using this link here: http://forum.xda-developers.com/showpost.php?p=18859438&postcount=199
While it is Gingerbread at least my phone is usable. I want to try his STOCK ICS method but that mentions the eMMC super-brick bug.
So this is what I have tried so far. I have tried installing Siyah 4.3.3 nomswap for my kernel using Mobil-Odin Lite. That works but it never reboots or actually says finished. What it does do is stay at the wicked purple splash with the yin yang symbol. I left it like that last night until I woke up this morning and it never changed. So I rebooted the phone and the Kernel is on there. I reboot into recovery so that I can install SHOstock3 v2.5.9. That goes off flawlessly except here the last few times it won't reboot when I go to the GO BACK. It sticks and doesn't do anything. Rebooting shows the SHOstock3 Engine Boot Animation. Once it stops it goes to ask me for the encryption password. Well I put in my password (was the same one to the unlock screen) and it reboots and you see the nifty Samsung animation logo and then goes to the Samsung Galaxy S2 Animation Logo and then just stays there. It really pisses me off.
So after all that I finally put a new Kernel on there,AJK 1,48s. Pretty cool it loads up and then reboots. Well AJK shows up after the light-blue bar fills up and then goes black and the 4 touch sensitive row keys are lit up for a bit before going dark but the phone is still on. So I rebooted to recovery (CWM now with the Kernel) fixed tweaks, went to advanced and saw all sorts of options. Tried clearing caches for ROM 2 and restarting,no effect. I removed ROM 2 and went through reboot and nothing. Restored ROM 2 and nothing. Re installed SHOstock3 v2.5.9. Did the same thing after install and not backing out when I hit GO BACK. Rebooted, same scenario that happened before with requiring password. Entering password does the same thing with a reboot and then staying on Samsung Splash Screen. If I Don't enter the password and reboot,same thing happens. So after being irritated and pissed off I ran Creepy's One-Click Fix again and paid attention to the phone and noticed it mentioned not being able to access the AT&T section or partition or something like that. So while part of my phone works under normal circumstances I want to figure out how to remove that encryption part of the phone and get full access (even though full memory and space are shown under Windows 7 and the files on the phone). The password I put on there isn't taking and I don't know if using PC methods for removing encryption (which could take awhile I know) needs to be employed (and if so which methods) or if that part is just screwed and I can't put on any other kernels or custom ROMs. Perhaps tell me where I messed up. Should I try swapping the ROMs from Advanced setting in CWM Recovery? Can I try a different ROM (kernel didn't seem to help)? I have done several factory resets dalvik cache wipes cache wipes formats,etc. and it is still there. I can say that before the whole encryption debacle (even though I was encrypted I did get in my phone after encrypting it) my pin unlock for my SIM wouldn't work and I actually SIM locked my phone. Had to go to AT&T and get a new SIM and was up and running. I put a 4 digit pin lock for the SIM (it let me do it) and when I went to unlock it after a reboot, it wanted an 8 pin for the PUK and wouldn't take what I put. I tried to change the PIN but to no avail. Once that happened I guess it snowballed. Any help is appreciated. I have searched and tried some things that looked to match my issue but none have totally helped. I do have ADB set up on my wife's laptop which I use to restore my phone to GB Stock ROM. I haven't been able to reboot the phone into Bootloader to do any fastboot commands as when I tried to do it the commands just sent the phone into normal reboot (though adb reboot recovery does boot to recovery). I Haven't tried booting to the bootloader using the new Kernel though so I will wait for confirmation or additional information before I try. Thanks guys.
Eagle
Couple of comments. Siyah 4.3.3 (and ajk) kernels are for 4.x ICS and JB so that explains why your stock Gingerbread system would not flash after you installed it. If you flash back to stock Gingerbread again, and then flash a custom kernel, use a kernel that is compatible with Gingerbread if you want to boot the system.
After doing a little research, it seems that a wipe data/factory reset will not clear the encryption, but a format data will. This information is not from a Samsung forum; it's from the Droid DNA forum. I'm thinking that the same thing may apply to the I777. See the thread here.
It might be worth a try anyway. Flash stock plus root Gingerbread, install mobile odin or mobile odin lite, and use it to flash Siyah 2.6.14. Boot into recovery and go to the Mounts and Storage section. There you can format data, (and all the other partitions, separately.)
creepyncrawly said:
Couple of comments. Siyah 4.3.3 (and ajk) kernels are for 4.x ICS and JB so that explains why your stock Gingerbread system would not flash after you installed it. If you flash back to stock Gingerbread again, and then flash a custom kernel, use a kernel that is compatible with Gingerbread if you want to boot the system.
After doing a little research, it seems that a wipe data/factory reset will not clear the encryption, but a format data will. This information is not from a Samsung forum; it's from the Droid DNA forum. I'm thinking that the same thing may apply to the I777. See the thread here.
It might be worth a try anyway. Flash stock plus root Gingerbread, install mobile odin or mobile odin lite, and use it to flash Siyah 2.6.14. Boot into recovery and go to the Mounts and Storage section. There you can format data, (and all the other partitions, separately.)
Click to expand...
Click to collapse
Thank you so much creepy. I will give that a try later and see how it goes. I hope the information I gave actually gives enough info. I know folks usually want enough. Ill post back my findings.
Eagle
quick follow up and what I tried
creepyncrawly said:
Couple of comments. Siyah 4.3.3 (and ajk) kernels are for 4.x ICS and JB so that explains why your stock Gingerbread system would not flash after you installed it. If you flash back to stock Gingerbread again, and then flash a custom kernel, use a kernel that is compatible with Gingerbread if you want to boot the system.
After doing a little research, it seems that a wipe data/factory reset will not clear the encryption, but a format data will. This information is not from a Samsung forum; it's from the Droid DNA forum. I'm thinking that the same thing may apply to the I777. See the thread here.
It might be worth a try anyway. Flash stock plus root Gingerbread, install mobile odin or mobile odin lite, and use it to flash Siyah 2.6.14. Boot into recovery and go to the Mounts and Storage section. There you can format data, (and all the other partitions, separately.)
Click to expand...
Click to collapse
Hey Creepy, I have a quick follow up and want to tell you what I have tried.
So I had already used Kies to move to AT&T v 4.0.4 ICS on my phone when I read your post. Rather than flashback again to GB I went ahead and put Siyah 4.3.3 on my phone. Went great, rebooted and installed quick and everything. Well I rebooted into recovery and went to mounts and storage and formatted the data and all that there and even formatted the secondrom data and all that. Did it a couple times to make sure everything was clean and good to go. Even put AJKs kernel on there after I ran the cleanrom script and it went flawlessly. I did factory resets and wipes and all that and installed SHOstock3 v2.5.9 and started up great. Well it got past the animation and the damn Password for encryption popped up. Well I put the wrong password in and it rebooted without the SAMSUNG screen and went through the boot ani and back to the password for encryption screen. I put the right password in, it reboots and you see the Samsung logo flash quickly and then it sticks on the Samsung Galaxy S2 Splash screen. I don't know what is holding it up from going forward unless when I messed up the first go around and it deleted everything if it didn't take out the bootload command or what have you. So I don't know if this idea will work but I am going to flashback to GB and put the siyah version on there that you linked and see if that will work.
One tihng, when Iencrypted the device the first go round, I onlydid the used data and area not the whole thing. Is this affecting it somehow? Any other ideas to try? I figured a full data format would remove the encryption but it never pops up saying all encryption will be removed. What I need is access to that area of the phone if I could just mount it on the computer. Is it possible after formatting the data, or before, that I should mount internal USB, DATA, etc and try another format/wipe or at least mount them to see if they can be used? Thanks for the help. For anyone else viewing this post (which actually is a lot) any help or ideas are appreciated. I am thinking I may need to format everything and get ahold of Samsung to see if they will reset my phone for me. I just wonder if the PIN lock on my SIM card that got locked when it wouldn't take my PIN didn't mess something up as well.
Eagle
WarEagleUS said:
Hey Creepy, I have a quick follow up and want to tell you what I have tried.
So I had already used Kies to move to AT&T v 4.0.4 ICS on my phone when I read your post. Rather than flashback again to GB I went ahead and put Siyah 4.3.3 on my phone. Went great, rebooted and installed quick and everything. Well I rebooted into recovery and went to mounts and storage and formatted the data and all that there and even formatted the secondrom data and all that. Did it a couple times to make sure everything was clean and good to go. Even put AJKs kernel on there after I ran the cleanrom script and it went flawlessly. I did factory resets and wipes and all that and installed SHOstock3 v2.5.9 and started up great. Well it got past the animation and the damn Password for encryption popped up. Well I put the wrong password in and it rebooted without the SAMSUNG screen and went through the boot ani and back to the password for encryption screen. I put the right password in, it reboots and you see the Samsung logo flash quickly and then it sticks on the Samsung Galaxy S2 Splash screen. I don't know what is holding it up from going forward unless when I messed up the first go around and it deleted everything if it didn't take out the bootload command or what have you. So I don't know if this idea will work but I am going to flashback to GB and put the siyah version on there that you linked and see if that will work.
One tihng, when Iencrypted the device the first go round, I onlydid the used data and area not the whole thing. Is this affecting it somehow? Any other ideas to try? I figured a full data format would remove the encryption but it never pops up saying all encryption will be removed. What I need is access to that area of the phone if I could just mount it on the computer. Is it possible after formatting the data, or before, that I should mount internal USB, DATA, etc and try another format/wipe or at least mount them to see if they can be used? Thanks for the help. For anyone else viewing this post (which actually is a lot) any help or ideas are appreciated. I am thinking I may need to format everything and get ahold of Samsung to see if they will reset my phone for me. I just wonder if the PIN lock on my SIM card that got locked when it wouldn't take my PIN didn't mess something up as well.
Eagle
Click to expand...
Click to collapse
Should I try TWRP instead of CWM and if so where should I grab it from?
Status Update
So this is what I have tried so far as of this moment.
I reflashed using your Stock + Root Gingerbread ROM.
Wiped DATA and everything in recovery menu several times.
Used Kernel Wipe and ROM Nuke for extra cleaning power.
Reinstalled the Kernel AJK and SHOstock3 ROM
Haven't installed any themes though I had Johns Blue and Villians Poison Base Theme (I believe that is what it is) on there when this all went down. Should I put them back on there?
Password still pops up. So what it looks like is that unless I stick with the unencrypted portion of the phone, I am screwed with any custom ROMs as the correct password has the phone restart and then stick at the Samsung Galaxy S2 Splash Screen. Apparently I still cannot access that area of the phones memory to wipe it at all no matter what I do. I need to access it somehow. Really driving me crazy and thinking I may need to talk with AT&T(as Samsung told me to earlier this morning lol) and see what they can do.
One thing I do notice is when I use your stock root program it actually removes the encryption or decrypts the section of the phone for the stock ROM to go on the phone which is cool.
Eagle
Any other things to try from anyone is greatly appreciated.
Been away all day. Sorry, I can't offer any other suggestions, but I have no experience with encryption. As you said, what you need to know is where the encryption is stored in memory so you can wipe or format that and restore it to original. If you can get to the right person, probably not level 1 tech support, then maybe you can find out. Somebody somewhere knows the answer to this.
would restoring my original EFS before this whole process help or is the encryption section totally blocked off?
WarEagleUS said:
would restoring my original EFS before this whole process help or is the encryption section totally blocked off?
Click to expand...
Click to collapse
I have no idea whether the encryption is stored there. What kind of efs backup did you take?
creepyncrawly said:
Been away all day. Sorry, I can't offer any other suggestions, but I have no experience with encryption. As you said, what you need to know is where the encryption is stored in memory so you can wipe or format that and restore it to original. If you can get to the right person, probably not level 1 tech support, then maybe you can find out. Somebody somewhere knows the answer to this.
Click to expand...
Click to collapse
Thx bro. yeah I need to run some forensic tools and see if I can mount the whole phone system on my PC and run the tools.
creepyncrawly said:
I have no idea whether the encryption is stored there. What kind of efs backup did you take?
Click to expand...
Click to collapse
a full efs backup. I made two or three actuakky using advanced efs, nitrality, and recovery.
WarEagleUS said:
a full efs backup. I made two or three actuakky using advanced efs, nitrality, and recovery.
Click to expand...
Click to collapse
A little research indicates that there is quite a bit of stuff stored in efs besides carrier specific data. So maybe encryption could be in there. Of those tools, nitrality for sure and maybe advanced efs should be able to restore the entire efs partition. If you are comfortable with the risk - a damaged efs would render the phone useless - then you might try this to see if it clears up the encryption issue. BTW, you should learn how to back up the efs partition yourself using terminal and linux commands.
creepyncrawly said:
A little research indicates that there is quite a bit of stuff stored in efs besides carrier specific data. So maybe encryption could be in there. Of those tools, nitrality for sure and maybe advanced efs should be able to restore the entire efs partition. If you are comfortable with the risk - a damaged efs would render the phone useless - then you might try this to see if it clears up the encryption issue. BTW, you should learn how to back up the efs partition yourself using terminal and linux commands.
Click to expand...
Click to collapse
Yeah I should have used ADB to do that from the get go. I should have used the wife's laptop like I started to instead of my WIN 8 machine has it seems to be finicky with Android SDK (the portion at least needed to run ADB). Linux commands really aren't much different than terminal and I have done both. I was actually trying to get fastboot commands to work but my bootloader wasn't cooperating and for the life of me I couldn't find how to unlock it. I may try restoring that EFS. If nothing else I would love to be able to format that EFS and replace it with my original copy though as you said a damaged EFS may actually cause issues (who knows if it is damaged). I do know that I am fixing to chat with AT&T support. I hope I don't have to drive down to Hoover, AL to the repair facility. I would rather them send me a phone and send this one back. I am on stock 4.0.4 ICS from AT&T and any root that may be on there (though I doubt there is now) I can remove and what not
Thanks for the advice and insight Creepy. I know you tried like hell to get me an answer but in doing research on here with other problems I found out some useful information going forward my friend.
Eagle
Well, looks like I will be getting a special early upgrade and the wife will as well. I will be keeping this phone, however, to mess with this and see if I cannot get this problem fixed. Thanks Creepy so much. I appreciate your research and help more than you know. If possible I would love to keep this thread open for a while just in case I figure this out and fix the issue. It may take me a week or so but I will get back to messing with it again.
A side note. You don't need the whole sdk to get adb. You can download just the files you need from my signature.
Sent from my SGH-I777 using xda premium
Hi, all! I'm sorry if this is in the wrong section, but I'm having a hard time trying to understand the different forums.
My Samsung Galaxy Ace (S5830) running under a custom ROM The Ultimatum (I've been using this custom firmware for a few weeks now, with no real problems up until now), is bootlooping with no apparent reason. On a rare occasion, most apps on the phone stopped responding and would crash upon opening, and would require a restart before they worked again. Well this happened to me a few hours ago, so I decided to reboot my phone. After coming back to check my phone, I had found it was still booting. This has gone on for several hours now, and I've tried turning it on and off, removing batteries and everything. It's stuck in bootloop. I found this was odd, as I have had no dramas with the firmware I've been using. I have not made ANY recent changes to the phone whatsoever, so I can hardly believe it would be my fault.
Now, my question is; how do I fix this without wiping all data and installing a clean ROM? I have a lot of stuff in the internal storage I can't afford to lose, and it's really important to me. A full wipe of all data would not be ideal. I can access recovery mode.
Thanks in advance, and I apologise if this is in the wrong forum!
You might want to ask to the rom thread for some help or ask in this section,
Galaxy Ace S5830 Q&A, Help & Troubleshooting
Anyway, I will try to help. If your custom recovery is support backup and restore (and advanced restore) your rom (check your custom recovery thread), try to backup your phone rom for now, so you could restore it back when solution not working.
Try to reflash the rom again without wipe data and reboot. If still in bootloop try to wipe data and reboot, see if that phone still bootloop.
If phone is successfully boot, go back to recovery and go to advanced restore, restore only data and then reboot. If still not working, then just full restore back to the phone to state before since I have no idea anymore.
That is the option I only know for now. However, try to ask help on section I link above or the rom thread before try this one, since I only familiar with Galaxy Gio (really similar to Ace) in the past.
I tried what you suggested but no positive results, really. I managed to boot after a full wipe, but restoring data locked it back into a bootloop. I'll try posting it in the other section.
Thanks.
Greetings-
I used the Cyanogenmod procedures to compile an image for my Note 3. The first time I installed it, the imaged booted up but I got a message about nfcservice not working. I do not recall the exact words, but it implied that nfcservice has an issue. I then, went into recovery and recovered an earlier image. The initial recovery try did not go well, and it was stuck. The last message was about the modem. But my next try worked. I had to use a backup I had from my stock firmware. Then I tried to install my unofficial image again. This time the phone went into download mode after I flashed my image. This keeps repeating, and I don’t know where to begin to troubleshoot this issue. Are there any logs I can look through? Aside from factory reset, I tried to clear all the other data; everything except the internal memory which holds my backups. But this did not fix anything. Do you have any advice for me? Oh, btw, this image is patched with seek-for-android patches. And I went through a lot to get it to work, since they did not support version 11. Thanks in advance.
RE
In my experience trying to troubleshoot something like this can be way more time consuming then un-rooting doing a factory reset back to stock OEM rom and then re-rooting and flashing the image again.
Hey All,
I've upgraded my 925F to Official MM 6.0.1. Rooted it through kernel Xspace and then installed recovery TWRP_3.0_MM_S6_by_ManhIT
My only concern is when I'm in TWRP I can't reboot, it just freezes.
I can nandroid backup no problem just the reboot part freezes TWRP.
Anyone else had this problem? is there another TWRP to be used?
nb : I tried clearing cache + dalvik, freezes still happen before rebooting.
thanks for ur help.
kaemon said:
Hey All,
I've upgraded my 925F to Official MM 6.0.1. Rooted it through kernel Xspace and then installed recovery TWRP_3.0_MM_S6_by_ManhIT
My only concern is when I'm in TWRP I can't reboot, it just freezes.
I can nandroid backup no problem just the reboot part freezes TWRP.
Anyone else had this problem? is there another TWRP to be used?
nb : I tried clearing cache + dalvik, freezes still happen before rebooting.
thanks for ur help.
Click to expand...
Click to collapse
Try this TWRP form arter... this is the only TWRP being use by many of us here.. you flash it through odin or recovery...
I had the same problem and i solved changing my kernel
Inviato dal mio SM-G925F utilizzando Tapatalk
fabiok81 said:
I had the same problem and i solved changing my kernel
Inviato dal mio SM-G925F utilizzando Tapatalk
Click to expand...
Click to collapse
The issue is not the kernel... its the recovery that doesn't work when reboot to system is touch and is freezing..
Go to advance then terminal
Write reboot
Easy!
Yes i know the iusse is about the recovery but it seems because there is not compatibility between some recovery and some kernel. I tried various recovery 3.0 and i have always a kind of freeze. The TWRP... by Manhit for example gave me freeze with xspace kernel but not with hacker kernel. I don't no the reason....
Inviato dal mio SM-G925F utilizzando Tapatalk
same but different
Hi All,
I'm experiencing a freeze in TWRP after about a few seconds, the whole recovery stands still and this happens every time.
I flashed the Xspace kernel which hasn't help.
The TWRP from arter97 works great, except it doesn't allow me to copy files to my PC using MTP, message says unexpected error.
yet, the ManhIT and Original TWRP allow me to copy data but both of them freeze up after a few seconds which causing the copying to fail.
Reasons I'm doing this is because my SM-G925F start looping and I've tried flashing stock so many times to no avail.
I'm sure all i need to do is data/ factory wipe and my phone will boot fine, I just really need some data before I do that.
Is there perhaps a different kernel I can try?
or if anyone has any suggestions that would be very much appreciated.
Regards
wahwahward said:
Hi All,
I'm experiencing a freeze in TWRP after about a few seconds, the whole recovery stands still and this happens every time.
I flashed the Xspace kernel which hasn't help.
The TWRP from arter97 works great, except it doesn't allow me to copy files to my PC using MTP, message says unexpected error.
yet, the ManhIT and Original TWRP allow me to copy data but both of them freeze up after a few seconds which causing the copying to fail.
Reasons I'm doing this is because my SM-G925F start looping and I've tried flashing stock so many times to no avail.
I'm sure all i need to do is data/ factory wipe and my phone will boot fine, I just really need some data before I do that.
Is there perhaps a different kernel I can try?
or if anyone has any suggestions that would be very much appreciated.
Regards
Click to expand...
Click to collapse
Try with hacker kernel. Wipe cache but not data
callumbr1 said:
Try with hacker kernel. Wipe cache but not data
Click to expand...
Click to collapse
Thanks for your response callumbr1.
I've attempted two different kernels:
g925-hacker-echoe-kernel-V14.zip
hacker-kernel-S6-Universal-V12.zip
Above mentioned problems persist.
Since arter97 TWRP is not freezing on me, if I run a back up on the Data only. Then perform the wipe, the backup should still be there, correct?
and lets say I flash the stock ROM again if necessary and I'm able to boot the device.
Would it be possible to restore that data back up at all ?
or perhaps copy that back up to my PC and access/extract the files with a separate application?
Many Thanks
wahwahward said:
Thanks for your response callumbr1.
I've attempted two different kernels:
g925-hacker-echoe-kernel-V14.zip
hacker-kernel-S6-Universal-V12.zip
Above mentioned problems persist.
Since arter97 TWRP is not freezing on me, if I run a back up on the Data only. Then perform the wipe, the backup should still be there, correct?
and lets say I flash the stock ROM again if necessary and I'm able to boot the device.
Would it be possible to restore that data back up at all ?
or perhaps copy that back up to my PC and access/extract the files with a separate application?
Many Thanks
Click to expand...
Click to collapse
I think best thing to do is get an otg storage adapter that plugs direct to phone. They are cheap.
Then run the backup of data and store on otg storage. Then you have it safe and it can be restored at a later time with restore option in twrp.
Or you can always do a full nandroid backup.
Can you get onto the phone now? Does it boot up?
Is there anything specific you need off the phone? To be backed up?
callumbr1 said:
I think best thing to do is get an otg storage adapter that plugs direct to phone. They are cheap.
Then run the backup of data and store on otg storage. Then you have it safe and it can be restored at a later time with restore option in twrp.
Or you can always do a full nandroid backup.
Can you get onto the phone now? Does it boot up?
Is there anything specific you need off the phone? To be backed up?
Click to expand...
Click to collapse
I plan on getting one of those, they seem extremely useful. A colleague has one which I plan to use tomorrow if they remember to bring it, I will then do as you suggest.
Never done a full nandroid back up before but will do some searching on that.
Phone still hangs at the Samsung splash screen.
And its really only pictures and some videos that I want, contacts would be nice too.
PS, this happened when I plugged my device into the PC to charge it was at about 5%, and I was making use of side sync to control the device when it just shutdown. I thought maybe the battery died so left it to charge a bit, it eventually tried to boot up by itself and its been looping ever since. Was really strange cause it gave me no issues prior to this. When I tried to get to the recovery it would hang at the "installing updates" section once I flashed the stock ROM I was able to get to recovery to wipe the cache but no luck.
Thanks for your suggestions much appreciated.
wahwahward said:
I plan on getting one of those, they seem extremely useful. A colleague has one which I plan to use tomorrow if they remember to bring it, I will then do as you suggest.
Never done a full nandroid back up before but will do some searching on that.
Phone still hangs at the Samsung splash screen.
And its really only pictures and some videos that I want, contacts would be nice too.
PS, this happened when I plugged my device into the PC to charge it was at about 5%, and I was making use of side sync to control the device when it just shutdown. I thought maybe the battery died so left it to charge a bit, it eventually tried to boot up by itself and its been looping ever since. Was really strange cause it gave me no issues prior to this. When I tried to get to the recovery it would hang at the "installing updates" section once I flashed the stock ROM I was able to get to recovery to wipe the cache but no luck.
Thanks for your suggestions much appreciated.
Click to expand...
Click to collapse
They are really useful, one of the best things ive ever bought regarding my phone. I use it daily now.
As for nandroid backup, it basically backs up absolutely everything including the firmware and data and all partitions. I always do it before flashing or modifying anything. Then if anything goes wrong, you just flash back your nandroid backup.
Can i ask before this happened did you use google photos? If so and sync was on they will all be saved. If you dont use it i reccomend you to use it from now on incase this ever happens in future.
See how you go making the backup when you can then if you need help regarding flashing the stock and getting the phone working ill help
callumbr1 said:
They are really useful, one of the best things ive ever bought regarding my phone. I use it daily now.
As for nandroid backup, it basically backs up absolutely everything including the firmware and data and all partitions. I always do it before flashing or modifying anything. Then if anything goes wrong, you just flash back your nandroid backup.
Can i ask before this happened did you use google photos? If so and sync was on they will all be saved. If you dont use it i reccomend you to use it from now on incase this ever happens in future.
See how you go making the backup when you can then if you need help regarding flashing the stock and getting the phone working ill help
Click to expand...
Click to collapse
Good day callumbr1
I never made use of google photos, not the biggest fan of cloud storage to be completely honest but I do see its benefits when it comes to times like these. lol
as for the device, last night I flashed a custom recovery (arter97) and made use of the SkipSoft Android ToolKit to pull my photos, videos and documents through the adb protocol. That being said, I have the data I wanted so all is well there.
However, after wiping the cache and doing a data / factory reset. I reflashed the stock ROM, it all goes swell until the android pops up with a message displaying " installing system updates". It gets to 32% changes to erasing then restarts , and this happens constantly no matter how many times I flash it or restart the device.
I read on another forum that my devices is probably dead and it could be the mother board. Any thoughts?
You think maybe a custom ROM would bring it up?
wahwahward said:
Good day callumbr1
I never made use of google photos, not the biggest fan of cloud storage to be completely honest but I do see its benefits when it comes to times like these. lol
as for the device, last night I flashed a custom recovery (arter97) and made use of the SkipSoft Android ToolKit to pull my photos, videos and documents through the adb protocol. That being said, I have the data I wanted so all is well there.
However, after wiping the cache and doing a data / factory reset. I reflashed the stock ROM, it all goes swell until the android pops up with a message displaying " installing system updates". It gets to 32% changes to erasing then restarts , and this happens constantly no matter how many times I flash it or restart the device.
I read on another forum that my devices is probably dead and it could be the mother board. Any thoughts?
You think maybe a custom ROM would bring it up?
Click to expand...
Click to collapse
Thats good about your data :good:
As for the little android guy and the installing updates then erasing, this normally happens. It happens every single time i restore and normally boots fine just after its not normally an issue. After yours says erasing does it then just reboot and restart the process of erasing constantly?
What i would suggest first is to flash a different stock ROM, preferably one with newest bootloader.
After flashing, boot to recovery and wipe dalvik cache. If it gets as far as the samsung logo just leave it as the first boot can take a while... like 30 minutes.
If that doesnt work try to flash a custom ROM. I reccomend CarHD ROM. I uave used it for quite some time and no issues.
It deffinately does not sound like motherboard issue. Normally you would have many issues and errors on boot prior to having main board issues.
See how you get on and keep me updated.
callumbr1 said:
Thats good about your data :good:
As for the little android guy and the installing updates then erasing, this normally happens. It happens every single time i restore and normally boots fine just after its not normally an issue. After yours says erasing does it then just reboot and restart the process of erasing constantly?
What i would suggest first is to flash a different stock ROM, preferably one with newest bootloader.
After flashing, boot to recovery and wipe dalvik cache. If it gets as far as the samsung logo just leave it as the first boot can take a while... like 30 minutes.
If that doesnt work try to flash a custom ROM. I reccomend CarHD ROM. I uave used it for quite some time and no issues.
It deffinately does not sound like motherboard issue. Normally you would have many issues and errors on boot prior to having main board issues.
See how you get on and keep me updated.
Click to expand...
Click to collapse
It doesn't say erasing after the first time. Right after the flash it will reboot to the blue screen with the android, it displays Installing update with a percentage bar which gets to 32% then that disappears and shows erasing, then again it shows installing update with no percentage bar. The android guy has a two arrows on his chest spinning which eventually stops. The device then reboots. It goes back to the Android guy but this time it shows "installing system update" without the percentage bar, it will then freeze again then reboot. That will continue forever until the battery dies.
After flashing though I can't seem to get to recovery to wipe the cache, I hit the buttons as I always do, but the blue screen and android always appears.
This is the stock ROM I'm currently using:
https://www.sammobile.com/firmwares/download/105085/G925FXXU4DPJB_G925FXFV4DPJ2_XFV/
Do you perhaps have a link to that custom ROM? would it work fine with the service provider here in SA (Vodacom) ?
And well at least that is some good news, I'm not too keen on having to take this into a shop and pay for parts.
wahwahward said:
It doesn't say erasing after the first time. Right after the flash it will reboot to the blue screen with the android, it displays Installing update with a percentage bar which gets to 32% then that disappears and shows erasing, then again it shows installing update with no percentage bar. The android guy has a two arrows on his chest spinning which eventually stops. The device then reboots. It goes back to the Android guy but this time it shows "installing system update" without the percentage bar, it will then freeze again then reboot. That will continue forever until the battery dies.
After flashing though I can't seem to get to recovery to wipe the cache, I hit the buttons as I always do, but the blue screen and android always appears.
This is the stock ROM I'm currently using:
https://www.sammobile.com/firmwares/download/105085/G925FXXU4DPJB_G925FXFV4DPJ2_XFV/
Do you perhaps have a link to that custom ROM? would it work fine with the service provider here in SA (Vodacom) ?
And well at least that is some good news, I'm not too keen on having to take this into a shop and pay for parts.
Click to expand...
Click to collapse
Thats pretty much exactly what happens to mine after restoring or flashing but mine boots up.
Flash the firmware again but in odin options uncheck auto reboot. This time after flashing, the phone should stay off. Then you can boot to recovery.
If that doesnt work, whilst it is on the blue screen with android guy hold only vol down and power, phone will reboot, as soon as the screen goes off switch to recovery combo and this should force it to recovery.
https://forum.xda-developers.com/galaxy-s6-edge/development/rom-carhdrom-1-t3111519/page1427
Here is the link to custom ROM, it will work fine on your phone. You need to flash this through TWRP. If you need steps on how to do this please tell me.
callumbr1 said:
Thats pretty much exactly what happens to mine after restoring or flashing but mine boots up.
Flash the firmware again but in odin options uncheck auto reboot. This time after flashing, the phone should stay off. Then you can boot to recovery.
If that doesnt work, whilst it is on the blue screen with android guy hold only vol down and power, phone will reboot, as soon as the screen goes off switch to recovery combo and this should force it to recovery.
https://forum.xda-developers.com/galaxy-s6-edge/development/rom-carhdrom-1-t3111519/page1427
Here is the link to custom ROM, it will work fine on your phone. You need to flash this through TWRP. If you need steps on how to do this please tell me.
Click to expand...
Click to collapse
Man I think I'm just going to try the custom to see if it works.
Would I need to flash a custom kernel or can it be stock?
After flashing the kernel with twrp I'm going to assume I would follow the same step.
1. flash TWRP custom recovery
2. copy .zip file to sdcard
3. go to recovery, install , select the .zip
Is that it or am I missing anything else when it comes to flashing ROMs through the recovery?
wahwahward said:
Man I think I'm just going to try the custom to see if it works.
Would I need to flash a custom kernel or can it be stock?
After flashing the kernel with twrp I'm going to assume I would follow the same step.
1. flash TWRP custom recovery
2. copy .zip file to sdcard
3. go to recovery, install , select the .zip
Is that it or am I missing anything else when it comes to flashing ROMs through the recovery?
Click to expand...
Click to collapse
Thats it.
Before installing rom go to wipe in TWRP, wipe data, dalvik, cache and system.
You dont need to flash a kernel though.
However when flashing carhd rom aroma installer will go through some choices, from there you can choose to install arter kernel. I reccomend doing this rather than keeping stock kernel.
Remember once installer complete and rom is installed leave it a while if it hangs on samsung logo screen. It can take a while to boot.
callumbr1 said:
Thats it.
Before installing rom go to wipe in TWRP, wipe data, dalvik, cache and system.
You dont need to flash a kernel though.
However when flashing carhd rom aroma installer will go through some choices, from there you can choose to install arter kernel. I reccomend doing this rather than keeping stock kernel.
Remember once installer complete and rom is installed leave it a while if it hangs on samsung logo screen. It can take a while to boot.
Click to expand...
Click to collapse
Currently waiting on the custom to download, don't have the quickest internet connection.
while I've been waiting, I've tried the stock ROM again.
something I forgot to mention before, which has happened a few times:
During the blue screen with the droid stating installing updates.
it switches to a screen with a big yellow triangle two dots below it and a dead droid.
After this I get to recovery, I wiped the cache and its getting to the samsung logo but freezes and then restarts all over again.
I'm just curious if you know what the yellow triangle thing means?
wahwahward said:
Currently waiting on the custom to download, don't have the quickest internet connection.
while I've been waiting, I've tried the stock ROM again.
something I forgot to mention before, which has happened a few times:
During the blue screen with the droid stating installing updates.
it switches to a screen with a big yellow triangle two dots below it and a dead droid.
After this I get to recovery, I wiped the cache and its getting to the samsung logo but freezes and then restarts all over again.
I'm just curious if you know what the yellow triangle thing means?
Click to expand...
Click to collapse
I think it normally means a failed update. Sometimes there are instructions to use smart switch other times it just means the update failed.
Try with the custom ROM and keep me updated.