I have had my Ultra Z since January. Zero problems, but this morning I removed my USB charger at work and a rubber gasket (see pic) fell out. Now the door does not close properly. I have the gasket and tried to work it back in but it would not go. There is a small tab and I cannot tell if it goes up (towards the screen) or down. I think I can get it back in with a toothpick or similar but want it to stay (and not lose it) and for it to re-seal the door properly. Not being able to close the USB door is a BIG deal to me.
I had been meaning to get a docking charger but bought some from China and they were crap. Guess I'll have to break down and get a real DK30.
The o-ring goes on the door.
Tab to back by the looks
Glue it back? What kind of glue?
Sent from my C6833 using XDA Free mobile app
mknewman said:
Glue it back? What kind of glue?
Sent from my C6833 using XDA Free mobile app
Click to expand...
Click to collapse
Try crazy glue very very small amount and please let it dry fully before putting the cap back into the phone!!!
Jammol said:
Try crazy glue very very small amount and please let it dry fully before putting the cap back into the phone!!!
Click to expand...
Click to collapse
Thanks Jammol. I'll try to figure this out. When I place it in the position it appears to belong in (now that I look closely I can see the small tab indention on the cap) but the part is so small I cannot even handle it with my big fat fingers, and don't really have a magnification station and stability setup to do it.
Big question is for the people who have had the cap break off, is there a source for the whole cap? Is it possible to install without taking the whole phone apart? Would it make sense to just throw it away and forget it was there?
mknewman said:
Thanks Jammol. I'll try to figure this out. When I place it in the position it appears to belong in (now that I look closely I can see the small tab indention on the cap) but the part is so small I cannot even handle it with my big fat fingers, and don't really have a magnification station and stability setup to do it.
Big question is for the people who have had the cap break off, is there a source for the whole cap? Is it possible to install without taking the whole phone apart? Would it make sense to just throw it away and forget it was there?
Click to expand...
Click to collapse
I don't know what part of the world you are in but you can check these out. Couple folks have bought them:
http://www.ebay.de/itm/Original-Son...zer_Ersatzteile_Werkzeuge&hash=item2339fdd95e
I say just replaced the entire cap with one of those and call it good. Mine is experiencing the same thing, tearing off little by little. I think that is where water might be getting into my phone, but I'll be replacing the phone soon anyways. Just not sure what to get yet.
I have not gotten mine wet yet other than rain in my pocket but the lines are much better with the cap on than removed, and I'd worry about the edge material getting pulled off the rest of the phone. I appreciate the ebay refrence and will try to find a US version. So is there a way to remove the old cap without breaking it off internally and having the tab rattling around inside?
I ordered a couple of the caps and a magnetic charger off thEbay US, but seller was in Spain so it will be a while. Crappy design trying to get rubber to adhere to plastic.
Does anyone know how to safely remove the old one? Just yank? slip something very thin in to try to get the tab to ride over the notch?
Thanks,
Marc
Super glue is what bonds o-rings to other materials because of the greasy slippery surface. Mine has also come loose. Contact glue, industrial glue or anything else wont bite on that thing because of its chemical resistance that the o-ring has.
try to get a hold of a bottle of Loctite 401 meanwhile if you can't wait for the parts
http://www.ebay.com/itm/LOCTITE-401...Instant-Adhesive-Super-Glue-20g-/121407567300
to remove the old one just pull..just a bit harder ...its kind of some bend at the end of the flap that's holding the thing in place inside the device.
Apply with a pin or paper clip I take it?
SÜPERUSER said:
Super glue is what bonds o-rings to other materials because of the greasy slippery surface. Mine has also come loose. Contact glue, industrial glue or anything else wont bite on that thing because of its chemical resistance that the o-ring has.
try to get a hold of a bottle of Loctite 401 meanwhile if you can't wait for the parts
http://www.ebay.com/itm/LOCTITE-401...Instant-Adhesive-Super-Glue-20g-/121407567300
to remove the old one just pull..just a bit harder ...its kind of some bend at the end of the flap that's holding the thing in place inside the device.
Click to expand...
Click to collapse
mknewman said:
Apply with a pin or paper clip I take it?
Click to expand...
Click to collapse
mmm something like that I dunno really.. I've yet have to figure this out myself lol. Use your imagination! :laugh:
At my moms work when I was young they had superglue bottles from loctite with really tiny metal pipes attached on them I wonder what loctite model that is. They could be used to do any precision work!
So it's possible to get the new one in properly once I get the old one out? From this picture it appears the new tab should slide in but I'm worried if you have to tug hard to get the old one out.
SÜPERUSER said:
to remove the old one just pull..just a bit harder ...its kind of some bend at the end of the flap that's holding the thing in place inside the device.
Click to expand...
Click to collapse
calm down...just pull on it. You won't break anything
edit: its no big deal to get the new one in
Great! Thanks, that's a relief. I'll let ya'll know how it goes when I get it. May buy a few extras too.
I got the replacement parts from thEbay tonight. Pulled on the old one and it came right out. Took 2-3 tries to get new one in. Tether was bunching up. Turns out if you hold it at about 45 regress it goes right in.
Thanks for the help everyone.
Sent from my C6833 using XDA Free mobile app
gutted!
I am so gutted i didn't see this thread before I sent my phone to Sony for warranty repair.
My gasket didn't fall off, it started to come unstuck so was hanging off and when closing the lid the gasket would unroll and the lid would open.
I sent it to Sony as I think this is there fault. The gasket should stay attached for the duration of the warranty.
They want to charge me £55 for repair, handling and shipping!! I have had my claim escalated and now they say 'upon further inspection the device is bent'!! They are willing to send it back free of charge should I not want to have it repaired...... But should I now expect the device they send back to me to bent when I know full well it was in near perfect condition when I sent to them?!?!
The bottom line is follow instructions from this thread. DO NOT send your phone to Sony.
Sony use 'authorised repair centres' so they don't even know what is going on with your device and the trust you put in Sony to give your device to a respected engineer is misplaced.
Related
Hi All, I'm one of the few who faced the problem where one side of the screen is slightly lifted on the edge. It doesn't cause any functional problems, but the springy feel is annoying. It's probably the adhesive on the left acting up and not sticking well. Press the screen down, and it will uplift within minutes. Tried the hot air method to melt the glue slightly, but no use.
So I probably want to replace the adhesive, and began looking for teardown guides.
None, however, really shows if the Gorilla glass can be pried off from the top ,leaving the rear un-dismantled. The flex cable should goes to the mainboard at the back, but I don't need to disconnect that for this purpose. I'm also not sure if I should pry the top or bottom.
If anyone has done it before, kindly share your experience here.
Thanks
Full replacement seems like the best idea.
Sent from my SGH-I997 using XDA App
bzmotoninja83 said:
Full replacement seems like the best idea.
Sent from my SGH-I997 using XDA App
Click to expand...
Click to collapse
oh. Why so? Seems like an overkill proposal...
I have the same exact dilemma. I see this is an old post, but maybe someone else can chime in. I really don't want to dismantle an otherwise working phone just to reapply adhesive. I like the phone but this seems like a really poor design.
Anyway, if anyone knows of a way I can reapply the adhesive without total dis-assembly I'd love to hear it!
Mr. Shickadance said:
I have the same exact dilemma. I see this is an old post, but maybe someone else can chime in. I really don't want to dismantle an otherwise working phone just to reapply adhesive. I like the phone but this seems like a really poor design.
Anyway, if anyone knows of a way I can reapply the adhesive without total dis-assembly I'd love to hear it!
Click to expand...
Click to collapse
sorry you cant, im replacing the digitizer for mine and u cant take off the glass without ripping off the flex cable for the digitizer.
i suppose u can heat up the adhesive and carefully open it alittle bit and put some glue on that corner. i say glue because you probably wont have room to put double sided tape and remove the second backing without tearing the flex cable for the digitizer.
I saw on a video that somebody could easily tear that kevlar piece out from right under the camera... It looks loose and flimsy, and not well stuck on the back of the phone.
Can anyone confirm this by sticking your nail under the weave right under the camera ? Last thing I want is to buy a phone for 600 bucks and have the back tear up on me after a month.
Fif23 said:
I saw on a video that somebody could easily tear that kevlar piece out from right under the camera... It looks loose and flimsy, and not well stuck on the back of the phone.
Can anyone confirm this by sticking your nail under the weave right under the camera ? Last thing I want is to buy a phone for 600 bucks and have the back tear up on me after a month.
Click to expand...
Click to collapse
Last thing i want to do is to try this for you!!
Sent from my XT910 using xda premium
Well the ability to put your nail under there alone will imply a design flaw.
Lol wut. Where did you read this at?
Any link to that vid?
ianford10 said:
Last thing i want to do is to try this for you!!
Sent from my XT910 using xda premium
Click to expand...
Click to collapse
+1
why would someone do this for you lol....
Fif23 said:
Well the ability to put your nail under there alone will imply a design flaw.
Click to expand...
Click to collapse
Well instead of getting another member to risk knackering there brand new handset why dont you just buy one, give it a go, report back here and if you can get your nail under there and your not happy take it back.
Stop asking other members to do stupid things to there expensive phones.
Sent from my XT910 using xda premium
I think its this video
Watch at around 3:50
shady_lanem said:
I think its this video
Watch at around 3:50
Click to expand...
Click to collapse
In day to day use this is not going to effect the device in any way.
Sent from my XT910 using xda premium
It's not the kevlar back but the plastic covering on the top (camera/flash/speaker) which can be taken off, possibly revealing some screws. Other than that there seems to be no way to open the device.
shady_lanem said:
I think its this video
Watch at around 3:50
Click to expand...
Click to collapse
This request/observation is just hilarious.
Why not take ANY phone and try to jam an ice pick between the edge of the glass and the phone. Hit it with a hammer.... does anything happen?
Or drop any phone from a really tall building, cause I'd hate to spend $600 on a phone and not have it survive something like.
Maybe put any phone in a blender, cause I'd hate to spend $600 on a phone and not have it blend properly.
syntrix said:
This request/observation is just hilarious.
Why not take ANY phone and try to jam an ice pick between the edge of the glass and the phone. Hit it with a hammer.... does anything happen?
Or drop any phone from a really tall building, cause I'd hate to spend $600 on a phone and not have it survive something like.
Maybe put any phone in a blender, cause I'd hate to spend $600 on a phone and not have it blend properly.
Click to expand...
Click to collapse
LMFAO
Sent from my XT910 using xda premium
syntrix said:
This request/observation is just hilarious.
Why not take ANY phone and try to jam an ice pick between the edge of the glass and the phone. Hit it with a hammer.... does anything happen?
Or drop any phone from a really tall building, cause I'd hate to spend $600 on a phone and not have it survive something like.
Maybe put any phone in a blender, cause I'd hate to spend $600 on a phone and not have it blend properly.
Click to expand...
Click to collapse
Nope, it isn't.
If I get a device and the plastic that covers the screws gets detached easily it's a build flaw. If the Kevlar thing gets detached it's a design flaw. If you drop your phone from a tall building or hit it with an hammer it's a flaw of your brain.
It's different.
I wouldn't pick at my RAZR like that anyways.
kholk said:
Nope, it isn't.
If I get a device and the plastic that covers the screws gets detached easily it's a build flaw. If the Kevlar thing gets detached it's a design flaw. If you drop your phone from a tall building or hit it with an hammer it's a flaw of your brain.
It's different.
Click to expand...
Click to collapse
I agree. The guy in the vid didn't use force. Come to think of it the OP didn't really meant to use force and try to open the back cover.
The cover we know is kevlar and durable. The material witch glues it on the phone how durable is it?
Tbh im in love with the back cover of the phone. I'd never put a cover/case on it. I wouldn't want to put one out of need( safe sex suxx )
Obviously, DrUnKenSTeiN is probably the only intelligent human on this post.
Where did anyone here read that I want you to remove the cover or bash it with a hammer ?
All I asked was to see if that thing is flimsy and all I got was raw violence by some members who probably have Attention deficit disorder (syntrix, ianford)
When I asked once if a certain laptop was flimsy, one intelligent human pressed on the lid lightly, checked for keyboard flex, and gave me his opinion.
You may say it's not important for daily use, but so does Android OS or a large screen. A smartphone can be productive without them, but this is not what discussion boards are about.
You may be excused to feel embarrassed, thanks.
Fif23 said:
Can anyone confirm this by sticking your nail under the weave right under the camera ? Last thing I want is to buy a phone for 600 bucks and have the back tear up on me after a month.
Click to expand...
Click to collapse
Just wanted to remind you of what you asked anyone to confirm with there brand new handset.
Maybe this pointless thread should be closed.
Sent from my Xoom using xda premium
Would just like to confirm that the phone in the video DOES have a defect. With all the force in the world I couldn't even get my fingernail under the Kevlar, let alone pry it up. He did it with no effort, like it was hanging off. Mine is sealed so tight (top, bottom and along the sides) you couldn't do anything to it if you tried.
sovrce said:
Would just like to confirm that the phone in the video DOES have a defect. With all the force in the world I couldn't even get my fingernail under the Kevlar, let alone pry it up. He did it with no effort, like it was hanging off. Mine is sealed so tight (top, bottom and along the sides) you couldn't do anything to it if you tried.
Click to expand...
Click to collapse
And the 18th post is the winner (crowd cheers and applause)!
If your phone is sealed then its not something that all razrs got. Seems like a flaw in the specific device.
Its important for guys that have bought the phone and its defective that they wont think that ,this is how the phone is.
sovrce said:
Would just like to confirm that the phone in the video DOES have a defect. With all the force in the world I couldn't even get my fingernail under the Kevlar, let alone pry it up. He did it with no effort, like it was hanging off. Mine is sealed so tight (top, bottom and along the sides) you couldn't do anything to it if you tried.
Click to expand...
Click to collapse
I messed around with 4 RAZR's today at three different stores. I even took out a penny that was scarred and I was not able to even scuff the Kevlar. It's on there on all the edges and sides REALLY REALLY good. And, that Kevlar is REALLY durable.
The one in the VIDEO MUST BE DEFECT.
Hi there, it's only me or the cover for USB and HDMI (but the second one is less important) sucks? opening it's ok with my nail but get back in closed position is hard -.-, and I have the fear to break the small plastic connection :S tips? I'm thinking about remove them...
I have got a technique to do it, but it's hard to explain. I push the top of the cover inside first, then the bottom.
Cholek3 said:
I have got a technique to do it, but it's hard to explain. I push the top of the cover inside first, then the bottom.
Click to expand...
Click to collapse
Exactly, it slides in at an angle, then click in the bottom.
I agree it looks flimsy; I had the same fear with the usb port cover on my X10 though, and it lasted well over 2 years of daily charging.
I am used to it now, it's still pointless though. My Nexus One had no cover and the USB port is still working fine after well over 2 years. I don't know why some manufacturers think a cover is necessary.
3Shirts said:
I am used to it now, it's still pointless though. My Nexus One had no cover and the USB port is still working fine after well over 2 years. I don't know why some manufacturers think a cover is necessary.
Click to expand...
Click to collapse
It's way prettier, obviously. I saw a picture on here with the cover removed, and it makes the design of the phone sink below sea level.
A flapless port only looks good on a phone with a metal or proper metal-color body. Like the Xperia P. But the Xperia S would look like crap without port flaps.
senne-vdb said:
It's way prettier, obviously. I saw a picture on here with the cover removed, and it makes the design of the phone sink below sea level.
Click to expand...
Click to collapse
Yeah but that's because you are taking the flap off when it was designed with it on. Phones designed with a flush usb port and no flap look fine.
It's like saying cutting the roof off your SUV didn't look good. A convertible sports car looks ace.
I don't think the XS would look bad with no port flap. Look at the headphone socket, that's very nicely styled. If they'd done the same with USB I'd be happier.
My samsung tocco ultra had a similar style flap to the XS and lasted me 2 years just fine despite me thinking it would only last two days.
The galaxy s had a slide cover which mostly did the job but wasn't exactly pretty. The pins in micro usb are pretty fine wouldn't take much ingress to mess it up.
I think when the flap spare pieces are available online I will get one and make proper opening for USB for it and leave it there permanently.
Some smart manufacturer could make a delete with correct opening. They could have made it just like Xperia P and it would look very nice.
I was thinking about such same thing. Waiting for spare USB flap availability.
I wonder if a replacement flap could be worked into a clip on case?
Si
Sent from my LT26i using XDA
Cholek3 said:
I have got a technique to do it, but it's hard to explain. I push the top of the cover inside first, then the bottom.
Click to expand...
Click to collapse
Ace, works for me too. I'd been faffing something chronic til now with it but that's deffo the method.
Good to hear that other people have had previous, port-protected Sony's last a couple of years and more OK, especially with 2 year contracts almost being the norm these days. All told it's encouraging, therefore, to read that Sony seems to be some kinda master of the flaps.
Too much innuendo - fnar!
I find the flaps very sturdy so I don't mind if they are a bit of a learning experience. I pop the bottom part, then the top part and it works for me XD.
On my X10 it was easy to remove but it was pretty fragile, so I would rather have it the way it is now, then none at all .
Sent from my LT26i using XDA
i think, it's hard to say whether it is better to have those flaps or not to have them (like in the xperia arc). of course, it also depends on how often you use them.
because of wifi, usb is mostly only needed for flashing, but at least you have to oben the usb-flap once a day for charging
but at the end the phone looks better with them...
The flaps don't bother me that much, but what does bother me is how loose they become after you have opened them a few times. It makes it feel like there is a loose spot in the casing.
I just wanted to chip in here and say if you're worried about the flap, you are right to be. I left mine charging overnight and when I came to unplug it I noticed that the flap had a crack in both sides somehow - despite me being super careful with it. It's not broken - some kind of membrane within seems to be holding it together somehow - but it bends along the crack now and it's a matter of time before it snaps completely.
I don't like that flap design one bit... I thought the X10 had a bad flap design but this one is far worse, especially when you have the phone in a case. It's vulnerable when being charged, sticking out worryingly... hopefully spares will become available. I tried to glue it to reinforce it but it's not easy as the crack is only a hairline when sitting properly.
I don't like them, on mine it has become loose and doesn't latch in at the bottom properly anymore. It has also list it's matte black and is quite shiny now, as is also the 'chin' bit at the bottom under clear strip, there's a definite bit of wear under the back and home buttons. :-/ 3 months old :|
Sent from my LT26i using XDA
Ungruntled said:
I just wanted to chip in here and say if you're worried about the flap, you are right to be. I left mine charging overnight and when I came to unplug it I noticed that the flap had a crack in both sides somehow - despite me being super careful with it. It's not broken - some kind of membrane within seems to be holding it together somehow - but it bends along the crack now and it's a matter of time before it snaps completely.
I don't like that flap design one bit... I thought the X10 had a bad flap design but this one is far worse, especially when you have the phone in a case. It's vulnerable when being charged, sticking out worryingly... hopefully spares will become available. I tried to glue it to reinforce it but it's not easy as the crack is only a hairline when sitting properly.
Click to expand...
Click to collapse
Well my cover finally cracked the other day, the little tail that stays in the phone always cracked in half. So half is still stuck in the phone and then I have the whole cover left. It won't stay on anymore so must look for a new one.
Any one seen the USB cover for sale anywhere ?
Mine has broken too, found this on ebay:
http://www.ebay.co.uk/itm/USB-HDMI-Cover-Button-Cap-Replacement-For-Sony-Ericsson-Xperia-S-LT26i-Black-/290718395563?pt=UK_Replacement_Parts_Tools&hash=item43b02aacab#ht_1834wt_1037
So, I see only one other thread about this, but I dropped my phone (Clumsy me left it on a chair, it slid off, and spider webbed my phone(SUCH a short distance)) But, I've bought the replacement part myself, and I plan on doing the repair myself. Is there anything I should know before I actually do this? Has total disassemble of the phone been done before?
Not to hijack your thread, but it drives me nuts how my LGOG seems to seek out-on its own-a way to dive off my coffee table/sofa/end table...no matter how flat and non inclined I sit it two seconds later and...CRASH! floor time...luckily mine has been taking it ok. So I feel your pain, and hope you get the help you seek.
Sent from my LG-E970 using xda premium
bqd37340 said:
Not to hijack your thread, but it drives me nuts how my LGOG seems to seek out-on its own-a way to dive off my coffee table/sofa/end table...no matter how flat and non inclined I sit it two seconds later and...CRASH! floor time...luckily mine has been taking it ok. So I feel your pain, and hope you get the help you seek.
Sent from my LG-E970 using xda premium
Click to expand...
Click to collapse
I even know your feeling -.- I've never dropped it before though, that was my first time, mostly because I treat my phones like its my second life, and because theyre expensive. This phone dropped literally a foot and webbed, I was so mad
Dr Protostar said:
I even know your feeling -.- I've never dropped it before though, that was my first time, mostly because I treat my phones like its my second life, and because theyre expensive. This phone dropped literally a foot and webbed, I was so mad
Click to expand...
Click to collapse
Found this video off a quick google search...
jtsurfs said:
Found this off a quick google search...
Click to expand...
Click to collapse
I've seen that video, but it doesn't really show how to put the replacement back in, if you use glue, what type of glue, or how much heat is required and all that such
Dr Protostar said:
I've seen that video, but it doesn't really show how to put the replacement back in, if you use glue, what type of glue, or how much heat is required and all that such
Click to expand...
Click to collapse
I replaced the digitizer on an HTC Vivid and used 3m double sided tape and doubled that up so the screen wasn't directly on top of the lcd. The video for that one recommended doing that to keep some weird effects on the screen.
given heisbig
jtsurfs said:
I replaced the digitizer on an HTC Vivid and used 3m double sided tape and doubled that up so the screen wasn't directly on top of the lcd. The video for that one recommended doing that to keep some weird effects on the screen.
Click to expand...
Click to collapse
Whats the youtube vid name?
Maybe try some silicone glue
Maybe try some of the silicone seal (blue silicone glue) to attach it. If nothing else you might try some electronic stores (specialty or other Cell phone repair stores) for the glue that is needed. I would opt for something that isn't so hard on stuck and maybe go for something that holds tight and seals well but doesn't make it damn near impossible.
UPDATE: So, the digitizer I bought developed a massive dead zone. I already contacted the amazon store I bought it from, they're replacing it for me. Why does this matter? Because now I get to update this post with pictures/video! So, yeah, I guess this guide should get a lot more helpful soon.
Update 2: Ok, so, I don't even know how to express my anger and frustration. This girl at work shoved my phone out of my hands and into the leg of a table, completely destroying my phone. So, yeah, sorry, I guess I won't be updating with pictures/video, because the amazon store isn't going to take the screen back now.
Yo, guys. If anyone noticed that I was gone, I'm flattered, since I don't post a lot. But yeah, I havent had my Optimus G in about a month, so I havent been on this forum. In that time, I went through my Second Motorola Atrix HD, a broken Galaxy S3, and even lived through Google Voice on my computer. It's an extremely long story, and kind of ridiculous, so I'll spare the details.
HOWEVER, I did finally just buy a replacement Digitizer and LCD screen, and successfully installed it, and I want to share tips for anyone doing it themselves.
When removing the back, after you've removed torx screws, start prying the back off from in between where the Sim card and MicroSD go. Where the back of the phone and the chassis of the phone are separate is much more obvious in that cavity, PLUS dents/dings from jamming a screwdriver in there wont be noticeable when you put the bay cover back on.
Don't force anything off. Make sure you've removed every screw, unclipped every clip, and removed ribbons from everything you're trying to take off.
Removing the battery is tricky. Be careful not to deform it too much, cause that's dangerous. But there are 2 strips of double sided tape running horizontally beneath the battery. Try to get something between the top one and the battery, then carefully pull the battery off the second strip with your hands. sticking too much stuff beneath it to pry it up is going to cause some trouble, so lifting it with your fingers might be better.
Remove the motherboard. detatch all the ribbons, antennae, everything, then pull up from the left, then slide left and out. This is how I got it out with the least resistance, but there is no science to it. If you've gotten this far, you can figure out how to pull it out without breaking it in half.
Components that need to be removed before LCD+Digitizer removal:
Motherboard
Battery
Camera
Just put them off to the side, you don't want them damaged during the next part.
WARNING! If you plan on saving your LCD screen, DO NOT DO THIS. The high heat will cook your screen and make it unusable. Only do this to remove a broken or unsavable Digitizer+LCD.
Alright, now pull out the heat gun. Alternatively, you can do what I did, and use a hair dryer. Not even kidding, this will work fine, and will be hilarious when you tell your friends about it.
On a high heat, start heating the screen. If you're using a heat gun, just do your thing, you know how it works. Hair dryer folks, keep the dryer very low to the phone, low enough to feel the dryer being pushed up by the air, holding it just high enough so it sort of hovers. (You'll know what I mean when you try it. If you don't, just keep it about half an inch off the phone.) Move the dryer along the edges of the screen, all the way around, thats where the glue is. It should heat up pretty fast.
Using your pry tool, start at the speaker grill and pry all the way around the phone. lifting just slightly upwards. If it's not extremely easy, apply more heat. Work all the way around, then pull the screen off. Be careful, it's likely you'll shatter the screen even more at this part if you're not careful. User Bozwell had an excellent suggestion (post 4), cover your screen in tape, then begin separating the screen to keep from getting glass everywhere. Great idea, Boz!
Alright, so from here on out, it's just reassembling your phone correctly. Piece o cake.
Firstly, put your new screen in. If it came with adhesive, it's up to you if you want to apply it now. I'd think you probably have to, but up to you.
If you're like me, and no adhesive was provided, hold off on doing anything for now. Just put the screen in the hole, and thread the ribbons through.
The motherboard lines up with some contacts on the chassis in a few places, but most importantly, there is a connection on the top left corner of the body, and the UNDERSIDE of the motherboard that needs to be made. I believe it's proximity sensor, but not sure. It's very difficult to tell if its attached, but look at what I'm describing, and try your best to mate them.
Don't forget ANY cables. Like, that's pretty obvious, but even when you're sure you didnt forget any, check again. The camera's ribbon is underneath the screen's, don't forget that one. I reassebled the whole thing, everything was working perfectly, except I no longer had any mobile connection. I couldn't imagine what I'd broken, since that's a whole different area, but going to phone status and checking my signal strength revealed I forgot to reconnect the white antennae (status showed my signal at -200,000 dbm). So, double check, because the more often you have to reopen your phone, the more flimsy it's going to get.
Alright, screw the plastic shielding back on, reconnect your battery, then flip the phone to be face up. Power it on, test the screen to make sure it's functional. If all is well, power off and glue the screen in. What I did, and I welcome anyone to tell me a better glue type or method, is plain ol Super glue along all the edges where the old glue was. Press it in, flip it over, and while it's drying, finish reassembling the phone (should just be make sure everything is screwed in inside, then put back glass back on.
If your screen wasn't functional, I guess try to get it replaced by whoever you bought it from, and leave your phone disassembled for when it gets to your house.
Alright, that's pretty much the thick and thin of it, it genuinely isn't that hard of a replacement. I've done a number of digitizer/lcd replacements, not bad at all. I hope this helped anyone stuck or wondering about anything. This video can be used as a rough example, but it goes really fast.
Good Luck!
replacement of lcd/digitzer
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
gruiz3 said:
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
Click to expand...
Click to collapse
Haha that's crazy, it bothers me how fragile this phone seems to be.
To keep the glass shards from going everywhere try covering the screen in tape before you start.
bozwell said:
To keep the glass shards from going everywhere try covering the screen in tape before you start.
Click to expand...
Click to collapse
Great idea, OP updated!
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
MoFoQ said:
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
Click to expand...
Click to collapse
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
ripin150 said:
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
Click to expand...
Click to collapse
I figured...though I've been eye-ing using the screen+digitizer+front housing if and when they get back into stock.
(digitizer only is also out-of-stock)