[SOLVED]
Turns out CMW 6.0.4.7 will not flash to this device - solution was to use the app "Flashify" from the play store which simply and easily installed TWRP
Thanks joshm.1219!
[SOLVED]
I am at a complete loss for a fix. Short story is: I wasn't receiving any MMS, so I finally decided to ODIN back to stock and used this method so I could keep my data. Here's what happened next:
- ODIN passed but I couldn't get past the Verizon logo
- Tried several suggested fixes but the last resort one worked; I wiped data & factory reset (thus defeating the purpose of the no-wipe ODIN... w/e)
- Everything loads fine, TouchWiz works but I get a Factory Mode popup and can't lock my screen. (still can't lock my phone even now but will use this method if I think I'm stuck with TouchWiz)
- I use this method to unlock bootloader and root - root confirmed.
- Try to install CWM recovery or TWRP (btw, where the hell did GooManager go and why is it so hard to find now) and they say successful but I simply can't boot into them, just keep getting the factory recovery screen which won't let me flash any roms or any non-signed .zips
- MMS Still doesn't work!
- I call VZW in desperation and somehow they magically reset my account services and MMS works again! (I probably could have done this in the first place and not lost my ROM/Data and sanity if I'd known)
I have looked high and low for a solution but have found none. I also have been unable to find a REGULAR stock MDK file to flash on this phone - I can only find the NO-WIPE version which doesn't even allow you to keep your data. I'm confused and frustrated and would love some active help, I just can't find the right threads/posts/ect.
Thank you kindly for any advice.. I love my S4 and have been using PA, PAC, CM and other ROMS since the day I got it - I need that back! TouchWiz is just... I just don't like it.
Try this one.
http://www.rwilco12.com/downloads.p...Galaxy S4 (Verizon) (SCH-I545)/Stock ROMs/TAR
FernBch said:
Try this one.
link
Click to expand...
Click to collapse
Thanks for the original stock.. sadly I am still ending up with the Android System Recovery and despite installing CWM Recovery, I just can't get to it. I also still get the ridiculous Factory Mode popup.
Any ideas? I'm so sad :'(
From off it's either home+volume down+power or home+volume up+power. One boots into stock recovery the other will boot into CWM.
Hold all three until you see some small blue text in the upper left of the screen.
FernBch said:
From off it's either home+volume down+power or home+volume up+power. One boots into stock recovery the other will boot into CWM.
Hold all three until you see some small blue text in the upper left of the screen.
Click to expand...
Click to collapse
Thanks for the effort but I'm well aware of that. As I said in the OP, I've been using custom ROMs on this since day one - the issue is that I cannot boot into CMW Recover, despite having a successful install via the app.
Dumb question, which app are you using? I use RomManager to install CWM (up to 6.0.4.7) and I have a flashable zip of 6.0.5.0.
877
FernBch said:
Dumb question, which app are you using? I use RomManager to install CWM (up to 6.0.4.7) and I have a flashable zip of 6.0.5.0.
Click to expand...
Click to collapse
I'm using ROM Manager but it won't work. I'd love to try ODIN flashing the CWM Recovery if you have the file for my MDK build.
I may have it on my PC at home. When I get there (60-90 min) I'll look. If I do I'll post up to Dropbox and give you a link.
Ok, I've searched my HDD and I don't have the CWM file. What I do have is the MDK all-in-one root+recovery tool for the I545. I can put it up and upload it if the file isn't too large but I don't know if that'll help you.
CWM 6.0.5.0 flashable zip is in the CM11 thread but I don't know if the recovery image in the file is good for you, either
Just use Flashify to get TWRP
joshm.1219 said:
Just use Flashify to get TWRP
Click to expand...
Click to collapse
I was about to complain about your assumption that I knew what that was.. then I found it on the play store and it actually worked! Thank you so much - now here's to hoping I can find a nice stable 4.4.4 ROM to put back on here!
I'm still at a loss for why ROM Manager was unable to flash CWMR but I guess I don't _need_ to know, I am so happy this is a big step after 3 days of touchwiz hell!
voice.lex said:
I was about to complain about your assumption that I knew what that was.. then I found it on the play store and it actually worked! Thank you so much - now here's to hoping I can find a nice stable 4.4.4 ROM to put back on here!
I'm still at a loss for why ROM Manager was unable to flash CWMR but I guess I don't _need_ to know, I am so happy this is a big step after 3 days of touchwiz hell!
Click to expand...
Click to collapse
As far as I know, the latest CWM doesn't work on our devices.
joshm.1219 said:
As far as I know, the latest CWM doesn't work on our devices.
Click to expand...
Click to collapse
Well, that explains it - Thank you so much!
voice.lex said:
Well, that explains it - Thank you so much!
Click to expand...
Click to collapse
No problem :thumb:
This thread might be dead, but rather than starting a new one for what is probably a stupid question, I'll ask it here and see what happens. I've been having major trouble flashing any 5.0 rom on my MDK VZW S4....Seems like every ROM fails when flashing. I have a feeling my issue is an outdated version of TWRP (2.5.0.2), but I am very hesitant to update because it seems like everyone has been having issues with 2.8.1.0. With this being said, are you guys currently running the most current version of TWRP and would you mind advising which .img file worked via Flashify? Not sure whether to use the jfltexxx or jfltevzw...or if it even matters.
I'm sure I've left out pertinent information, but let me know what I'm missing and I'll update accordingly.
I've been using the latest version of TWRP 2.8.1.0 and running Euroskank Lollerpop with zero issues. Coincidentally, TWRP just got updated today to 2.8.3.0 which i have yet to flash but will do so shortly. I would recommend JFLTEVZW based on my usage. Not sure if the other variant works or not but it appears you have a verizon device so stick with JFLTEVZW.
760hacker said:
I've been using the latest version of TWRP 2.8.1.0 and running Euroskank Lollerpop with zero issues. Coincidentally, TWRP just got updated today to 2.8.3.0 which i have yet to flash but will do so shortly. I would recommend JFLTEVZW based on my usage. Not sure if the other variant works or not but it appears you have a verizon device so stick with JFLTEVZW.
Click to expand...
Click to collapse
Thank you very much for getting back to me. When you flashed 2.8.3.0, was it a .zip file from recovery or a .IMG through flashify or another app? Thanks again for your help!
swh969 said:
Thank you very much for getting back to me. When you flashed 2.8.3.0, was it a .zip file from recovery or a .IMG through flashify or another app? Thanks again for your help!
Click to expand...
Click to collapse
.IMG file, flashify is so simple!
Sent from my Nexus 7 using Tapatalk
760hacker said:
.IMG file, flashify is so simple!
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
I'm going to give it a shot! Thanks again for your help.
Worked like a charm. Thanks @760hacker
Related
Guys I am in dire need of some help. I have a VZW GS4 i545 and I flashed the new 'merged' version of PHilz touch for the GS4 only to find out it is non-Loki'd so now I am getting the error message "Software not authorized by Verizon".
I know I need to use Odin to get back but I don't know how to use it to replace the boot loader.
Can someone please tell me or point me to a step-by-step?
I've Googled this many different ways but I can't seem to find what I need.
Please help.
ktraub said:
Guys I am in dire need of some help. I have a VZW GS4 i545 and I flashed the new 'merged' version of PHilz touch for the GS4 only to find out it is non-Loki'd so now I am getting the error message "Software not authorized by Verizon".
I know I need to use Odin to get back but I don't know how to use it to replace the boot loader.
Can someone please tell me or point me to a step-by-step?
I've Googled this many different ways but I can't seem to find what I need.
Please help.
Click to expand...
Click to collapse
Just flash the no wipe mdk tar...you don't just flash bootloaders... It will replace recovery image which is what you need...you will have to re-flash a loki'd image after
jamesd1085 said:
Just flash the no wipe mdk tar...you don't just flash bootloaders... It will replace recovery image which is what you need...you will have to re-flash a loki'd image after
Click to expand...
Click to collapse
Jamesd1085, thanks for the reply.
But, how do I flash with the " Software not authorized by Verizon" message up?
I don't know how to get the phone back into download mode with that message up.
Your help is greatly appreciated.
ktraub said:
Jamesd1085, thanks for the reply.
But, how do I flash with the " Software not authorized by Verizon" message up?
I don't know how to get the phone back into download mode with that message up.
Your help is greatly appreciated.
Click to expand...
Click to collapse
Pull the battery then try to get into download mode again. Here's a thread with a guide. Make sure you get the mdk file and not another one as you'd end locking your phone up.
http://forum.xda-developers.com/showthread.php?t=2301259
Sent From My Verizon S4
ktraub said:
Jamesd1085, thanks for the reply.
But, how do I flash with the " Software not authorized by Verizon" message up?
I don't know how to get the phone back into download mode with that message up.
Your help is greatly appreciated.
Click to expand...
Click to collapse
To turn it off pull battery... After that you can boot into download mode by holding volume down and power button...after that you can flash via odin
Mistertac said:
Pull the battery then try to get into download mode again. Here's a thread with a guide. Make sure you get the mdk file and not another one as you'd end locking your phone up.
http://forum.xda-developers.com/showthread.php?t=2301259
Sent From My Verizon S4
Click to expand...
Click to collapse
Mistertac, thanks for the response. I pulled the battery and the phone booted into my custom ROM HyperDrive RLS 14, and I still have root.
I think I may have just hosed my recovery. While I'm waiting for the no wipe mdk to download (another 2 hours), is there nay way to just flash the recovery?
Your help is greatly appreciated.
ktraub said:
Mistertac, thanks for the response. I pulled the battery and the phone booted into my custom ROM HyperDrive RLS 14, and I still have root.
I think I may have just hosed my recovery. While I'm waiting for the no wipe mdk to download (another 2 hours), is there nay way to just flash the recovery?
Your help is greatly appreciated.
Click to expand...
Click to collapse
Well you can easily re install your recovery of choice still. Either with goo or rom manager.
Sent From My Verizon S4
Mistertac said:
Well you can easily re install your recovery of choice still. Either with goo or rom manager.
Sent From My Verizon S4
Click to expand...
Click to collapse
Mistertac, thank you very much!
I installed Goo manager and then used it to install TWRP.
The I rebooted to recovery and flashed the correct (loki'd) version of Philztouch.
Thank you again. I really appreciate it.
-Kev
ktraub said:
Mistertac, thank you very much!
I installed Goo manager and then used it to install TWRP.
The I rebooted to recovery and flashed the correct (loki'd) version of Philztouch.
Thank you again. I really appreciate it.
-Kev
Click to expand...
Click to collapse
Glad we could help. And even better that you flashed the Loki'd version of Philz or you'd be using Odin after all lol
Sent From My Verizon S4
Mistertac are you familiar with philz touch?...jw because last week I installed it and loved the ui and extra features but it wouldn't allow me to flash anything...I ended up having to use ROM toolbox to flash cwm touch 6.0.4.4...any Ideas...everybody seems to swear by Philz touch and I would rather use it...I tried toggling Loki support on and off it wouldn't flash regardless of settings
jamesd1085 said:
Mistertac are you familiar with philz touch?...jw because last week I installed it and loved the ui and extra features but it wouldn't allow me to flash anything...I ended up having to use ROM toolbox to flash cwm touch 6.0.4.4...any Ideas...everybody seems to swear by Philz touch and I would rather use it...I tried toggling Loki support on and off it wouldn't flash regardless of settings
Click to expand...
Click to collapse
Yes I use Philz. Are you flashing our device specific Philz zip or the unified jflte zip? Because some were having problems with the unified one
Sent From My Verizon S4
Mistertac said:
Yes I use Philz. Are you flashing our device specific Philz zip or the unified jflte zip? Because some were having problems with the unified one
Sent From My Verizon S4
Click to expand...
Click to collapse
Dunno...lol...I downloaded it from the philz touch op for jfltevzw...but I will have to look again...it was most recent version but I didn't see anything about a unified version...thanks for the heads up
jamesd1085 said:
Dunno...lol...I downloaded it from the philz touch op for jfltevzw...but I will have to look again...it was most recent version but I didn't see anything about a unified version...thanks for the heads up
Click to expand...
Click to collapse
Yea I'd grab the latest one from here..
http://goo.im/devs/philz_touch/CWM_Advanced_Edition/jfltevzw
Sent From My Verizon S4
Mistertac said:
Yea I'd grab the latest one from here..
http://goo.im/devs/philz_touch/CWM_Advanced_Edition/jfltevzw
Sent From My Verizon S4
Click to expand...
Click to collapse
Yeah I had the previous build from here...maybe just a fluke...Lil...I will try the new version...thanks
Hello XDA members,
I was hoping somebody would help me out, I'm fairly new when it comes to installing custom roms so I require your patience. I don't know how to install a custom rom onto my Bell Atrix HD MB886, everytime I try it says abortion failed, what can I do to fix this. I have wiped data and all that probably 5 times in the past week alone. I would like to know how to successfully install roms without errors. Both the times that I have done this I had my bootloader unlocked, and I had clockword recovery mod latest version 6.0.4.4. I bought an SD card today to help install the roms because otherwise I can't do it from my internal storage. I really hope somebody can help me out.
Regards,
Roger
riekkir said:
Hello XDA members,
I was hoping somebody would help me out, I'm fairly new when it comes to installing custom roms so I require your patience. I don't know how to install a custom rom onto my Bell Atrix HD MB886, everytime I try it says abortion failed, what can I do to fix this. I have wiped data and all that probably 5 times in the past week alone. I would like to know how to successfully install roms without errors. Both the times that I have done this I had my bootloader unlocked, and I had clockword recovery mod latest version 6.0.4.4. I bought an SD card today to help install the roms because otherwise I can't do it from my internal storage. I really hope somebody can help me out.
Regards,
Roger
Click to expand...
Click to collapse
Hi there. A failed abortion certainly seems like an issue... I guess I am not totally clear on the status here. You say that you had CWM. Do you still have it? Bootloader is still unlocked? What rom are you trying to install? Are you certain it's for the Bell version and not like the AT&T one? What is the exact error message?
es0tericcha0s said:
Hi there. A failed abortion certainly seems like an issue... I guess I am not totally clear on the status here. You say that you had CWM. Do you still have it? Bootloader is still unlocked? What rom are you trying to install? Are you certain it's for the Bell version and not like the AT&T one? What is the exact error message?
Click to expand...
Click to collapse
No I don't have it atm as I just wiped the data/cache last night but will I already have CWM, I just need to unlock the bootloader and try again...I'm trying to install this one:
Android 4.4.2 KitKat Mokee Rom, and it says the version is a nightly. Yes I'm positive it's the Bell Version as I purchased it at a Bell Store and my carrier is Bell. The error message is "Installation Aborted." It begins installing, and then halfway through I get that error message. How do I fix this?
I figured you knew what phone you had. I was wondering if you had a rom built for the Bell version vs an ATT one. But since you are using a CM based rom, it obviously doesn't matter. Curious as to why you are bothering with relocking the bootloader? But I suggest to either try a different version of the rom, or to change your recovery to one of the Philz Touch versions as that's what some of the other users in that thread for the rom for your phone were using. You can find them here:
http://goo.im/devs/philz_touch/CWM_Advanced_Edition/moto_msm8960
es0tericcha0s said:
I figured you knew what phone you had. I was wondering if you had a rom built for the Bell version vs an ATT one. But since you are using a CM based rom, it obviously doesn't matter. Curious as to why you are bothering with relocking the bootloader? But I suggest to either try a different version of the rom, or to change your recovery to one of the Philz Touch versions as that's what some of the other users in that thread for the rom for your phone were using. You can find them here:
Click to expand...
Click to collapse
No I was bothering to unlock it again, not lock it. Where can I find different versions for the 4.4.2 Mokee Rom? I've tried using the Philz Touch version: Motorola Atrix HD One Click Philz recovery installer and when I tried it a couple of times it said it failed to install although I'm not sure why. I came across these images the other day but how do I use the .img files on my device, as I'm not sure to proceed from here once I have them downloaded.
riekkir said:
No I was bothering to unlock it again, not lock it. Where can I find different versions for the 4.4.2 Mokee Rom? I've tried using the Philz Touch version: Motorola Atrix HD One Click Philz recovery installer and when I tried it a couple of times it said it failed to install although I'm not sure why. I came across these images the other day but how do I use the .img files on my device, as I'm not sure to proceed from here once I have them downloaded.
Click to expand...
Click to collapse
I was curious as why you relocked it in the first place.
Where are you getting Mokee from that doesn't have a link to their Downloads?
http://forum.xda-developers.com/showthread.php?t=2619489
For installing recovery:
http://forum.xda-developers.com/showthread.php?t=2262726
es0tericcha0s said:
I was curious as why you relocked it in the first place.
Where are you getting Mokee from that doesn't have a link to their Downloads?
For installing recovery:
Click to expand...
Click to collapse
thanks will try this out and let you know later how it works! I download the custom rom from true android blogspot.ca (can't post links just yet, annoying).
riekkir said:
thanks will try this out and let you know later how it works! I download the custom rom from true android blogspot.ca (can't post links just yet, annoying).
Click to expand...
Click to collapse
Right on. Well, you should bookmark the thread here on XDA because that's typically where the action happens.
es0tericcha0s said:
Right on. Well, you should bookmark the thread here on XDA because that's typically where the action happens.
Click to expand...
Click to collapse
Okay so I'm trying it now and the program won't even open :/
Odd. I just downloaded it to test and I didn't have any issues. If you can't get the actual application / exe file to open, then just use the Main-Skip.bat. Does the same thing.
If it doesn't open still, make sure that you have your anti-virus off as sometimes those interfere with programs like this. Might also try as admin.
es0tericcha0s said:
Odd. I just downloaded it to test and I didn't have any issues. If you can't get the actual application / exe file to open, then just use the Main-Skip.bat. Does the same thing.
If it doesn't open still, make sure that you have your anti-virus off as sometimes those interfere with programs like this. Might also try as admin.
Click to expand...
Click to collapse
Okay I wasn't looking at the actual .exe sorry, I got it to work and all I installed the Philz One Touch Recovery from that program, just downloaded a different rom and all and then I select the apply update from external storage and when it gets to the verifying update package, it gave me the same error message as yesterday, Installation Aborted.
So again, how do I fix this, am I doing something wrong? Why won't my custom rom install?
riekkir said:
Okay I wasn't looking at the actual .exe sorry, I got it to work and all I installed the Philz One Touch Recovery from that program, just downloaded a different rom and all and then I select the apply update from external storage and when it gets to the verifying update package, it gave me the same error message as yesterday, Installation Aborted.
So again, how do I fix this, am I doing something wrong? Why won't my custom rom install?
Click to expand...
Click to collapse
I don't think that is the most updated version. What's the version number of the recovery that was installed? It should be listed on the main page of it when you boot there. I was suggesting to use one of the new ones. It might have something to do with the SELinux support that KK roms need. You just have to put the img file in the tools folder and rename the new one the same. But here's no other error that shows up other than Installation Aborted? I was thinking usually it would have an error code or some other message.Have you checked the md5 of the rom zip to make sure it's not corrupted (if the dev provided it)?
es0tericcha0s said:
I don't think that is the most updated version. What's the version number of the recovery that was installed? It should be listed on the main page of it when you boot there. I was suggesting to use one of the new ones. It might have something to do with the SELinux support that KK roms need. You just have to put the img file in the tools folder and rename the new one the same. But here's no other error that shows up other than Installation Aborted? I was thinking usually it would have an error code or some other message.Have you checked the md5 of the rom zip to make sure it's not corrupted (if the dev provided it)?
Click to expand...
Click to collapse
Use one of the new versions of that program or to use the latest CWM which I have been. Okay I really don't know how to do that and where to move it to, how do I do such a thing? No it just says Installation Aborted... How would I do that? And yes I downloaded the new rom directly from his site.
riekkir said:
Use one of the new versions of that program or to use the latest CWM which I have been. Okay I really don't know how to do that and where to move it to, how do I do such a thing? No it just says Installation Aborted... How would I do that? And yes I downloaded the new rom directly from his site.
Click to expand...
Click to collapse
Look in the tools folder of the zip you downloaded. Download the newest Philz Touch img from the other link from earlier. Rename it to replace the one in the tools folder. Redo the recovery install. But you didn't say what version you already have.
es0tericcha0s said:
Look in the tools folder of the zip you downloaded. Download the newest Philz Touch img from the other link from earlier. Rename it to replace the one in the tools folder. Redo the recovery install. But you didn't say what version you already have.
Click to expand...
Click to collapse
Okay that did the trick, properly got philz recovery installed, did the install again, this time it worked, clicked reboot and now it's stuck at the Dual Core bootlogo screen
riekkir said:
Okay that did the trick, properly got philz recovery installed, did the install again, this time it worked, clicked reboot and now it's stuck at the Dual Core bootlogo screen
Click to expand...
Click to collapse
Did you do a full wipe, including wiping /system?
If you didn't, it should be under Mounts and Storage > Format /system of something of that sort.
es0tericcha0s said:
Did you do a full wipe, including wiping /system?
If you didn't, it should be under Mounts and Storage > Format /system of something of that sort.
Click to expand...
Click to collapse
No I forgot to do that dammit, can't get into recovery mode and my computer doesn't recognize my phone now, think I bricked it.
riekkir said:
No I forgot to do that dammit, can't get into recovery mode and my computer doesn't recognize my phone now, think I bricked it.
Click to expand...
Click to collapse
Pop the battery out for a bit, then pop it back in and hold Volume Down while powering up. Should get you into fastboot where you can skip to the recovery.
es0tericcha0s said:
Pop the battery out for a bit, then pop it back in and hold Volume Down while powering up. Should get you into fastboot where you can skip to the recovery.
Click to expand...
Click to collapse
The battery doesn't come out of my phone as you can't take the back off. I got into fast boot easily them selected recovery and nothing happened, I think my phone is screwed
riekkir said:
The battery doesn't come out of my phone as you can't take the back off. I got into fast boot easily them selected recovery and nothing happened, I think my phone is screwed
Click to expand...
Click to collapse
Oh yea, forgot you have to undo the screws on the bottom. So you scroll down to hit recovery and use the Power button to select and it doesn't do anything? That's odd.. Try and reflash the recovery since you can still get to fastboot. If that doesn't work, you're not totally screwed since you can still get to fastboot, that means you should be able to restore it to stock and start over.
Alternatively, if you have fastboot set up, you could make sure that philz touch is in the fastboot folder and use this command:
fastboot boot recovery nameofphilztouchfile.img
If you don't have fastboot, then just grab this one: http://forum.xda-developers.com/showthread.php?t=2317790 , drop the recovery img in that folder and open the CMD prompt on your computer and change directories to it and run the command.
Well i used to have a hox+ with Android Revolution custom rom and a custom kernel. I tried to power it up but it stucks at htc logo,then reboots and goes straight to twrp recovery. I tried to flash again the rom via adb but i can't see my device in cmd. I found and dowloaed htc drivers my htc,plus adk and htc sync manager but still no luck..any ideas what is going on here?
do a full system reset in cwm recovery
now install the rom
reboot into fastboot
fastboot flash boot boot.img for the rom
i360droid said:
do a full system reset in cwm recovery
now install the rom
reboot into fastboot
fastboot flash boot boot.img for the rom
Click to expand...
Click to collapse
fastboot is not recognised etc...........any ideas?
smavr said:
fastboot is not recognised etc...........any ideas?
Click to expand...
Click to collapse
ok, add me on skype, i360faceplant, i will walk you through it step by step
i360droid said:
ok, add me on skype, i360faceplant, i will walk you through it step by step
Click to expand...
Click to collapse
Well i actually found what happened..my old hox+ works perfectly now..thanks for your help anyway
smavr said:
Well i actually found what happened..my old hox+ works perfectly now..thanks for your help anyway
Click to expand...
Click to collapse
what was up with it?
i360droid said:
what was up with it?
Click to expand...
Click to collapse
Well, i just made a mistake at adb sideload...
smavr said:
Well, i just made a mistake at adb sideload...
Click to expand...
Click to collapse
lol
i360droid said:
lol
Click to expand...
Click to collapse
Somewhat similar situation. I previously rooted my HTC One X+ (Intl) with Viper X+ rom. I thought I would experiment with it as it is no longer my daily phone, and since I liked the Cyanogen experience on OnePlus One, thought i would try to install it on the HOX+.
I followed these official (?) instructions http://wiki.cyanogenmod.org/w/Install_CM_for_enrc2b#Installing_recovery_using_fastboot, however, after getting CWM recovery on and then flashing via sideload command the ROM, I am now stuck in the CM bootloop animation and computer no longer recognises the device, and can't find anyway to get back to bootloader, recovery etc.
I did read about bootloop issues after this and some people said that the boot.imhg file should have been flashed separately (thanks CM for not including that instruction!), and somehow my computer recognised it one more time after the bootlooping started and I managed to get into fastboot to flash boot.img, but, then rebooted and bootloop again. Since then I have had no way to get back into recovery or bootloader, so it just runs until battery dies.
Should it go into the bin? Or anything else I should try?
Thanks so much for any
EDIT: Solved...I was able to get recovery back, then did full reset and followed instructions above re boot.img flash and now am back into my phone with a new lease on life and CM ROM!!
Two more noob questions if I may, now that I have my HOX+ back...
I am now running CM 10.2.1-enrc2b.
I have 3 updates available and being offered to me (upgrade to CM11 from CM10):
- cm-11-20140308-SNAPSHOT-M4
- cm-11-20140916-SNAPSHOT-M10
- cm-11-20140916-SNAPSHOT-M12
1. I downloaded and installed the latest M12, but upon rebooting it went into a bootloop for 15mins+. I then followed your instructions again to get back. So, it seems I at least need to install them in order starting from the earliest (ie M4), but before doing so I wanted to check if anyone knows if these are even compatible with my HOX+ (Intl)?
2. Which would be the best place to get the right gapps package and installation instructions (if CM can get it wrong, am now wary of someone else leaving out the critical boot.img flash step eg)?
Thanks!
Sent from my Nexus 7 using XDA Free mobile app
EDIT: Nothing like some self-help. I am good now.
ahighfield said:
Somewhat similar situation. I previously rooted my HTC One X+ (Intl) with Viper X+ rom. I thought I would experiment with it as it is no longer my daily phone, and since I liked the Cyanogen experience on OnePlus One, thought i would try to install it on the HOX+.
I followed these official (?) instructions http://wiki.cyanogenmod.org/w/Install_CM_for_enrc2b#Installing_recovery_using_fastboot, however, after getting CWM recovery on and then flashing via sideload command the ROM, I am now stuck in the CM bootloop animation and computer no longer recognises the device, and can't find anyway to get back to bootloader, recovery etc.
I did read about bootloop issues after this and some people said that the boot.imhg file should have been flashed separately (thanks CM for not including that instruction!), and somehow my computer recognised it one more time after the bootlooping started and I managed to get into fastboot to flash boot.img, but, then rebooted and bootloop again. Since then I have had no way to get back into recovery or bootloader, so it just runs until battery dies.
Should it go into the bin? Or anything else I should try?
Thanks so much for any
EDIT: Solved...I was able to get recovery back, then did full reset and followed instructions above re boot.img flash and now am back into my phone with a new lease on life and CM ROM!!
Click to expand...
Click to collapse
to get into bootloader, hold down the vol down and power, the home lights will flash (atleast they do when its booting), it will reboot, when you get the htc logo, let go of power button. and now try a stable er version of the rom.
---------- Post added at 02:42 PM ---------- Previous post was at 02:40 PM ----------
ahighfield said:
Two more noob questions if I may, now that I have my HOX+ back...
I am now running CM 10.2.1-enrc2b.
I have 3 updates available and being offered to me (upgrade to CM11 from CM10):
- cm-11-20140308-SNAPSHOT-M4
- cm-11-20140916-SNAPSHOT-M10
- cm-11-20140916-SNAPSHOT-M12
1. I downloaded and installed the latest M12, but upon rebooting it went into a bootloop for 15mins+. I then followed your instructions again to get back. So, it seems I at least need to install them in order starting from the earliest (ie M4), but before doing so I wanted to check if anyone knows if these are even compatible with my HOX+ (Intl)?
2. Which would be the best place to get the right gapps package and installation instructions (if CM can get it wrong, am now wary of someone else leaving out the critical boot.img flash step eg)?
Thanks!
Sent from my Nexus 7 using XDA Free mobile app
EDIT: Nothing like some self-help. I am good now.
Click to expand...
Click to collapse
ok, dont do an ota update in cm, you need s-off, which you cant get on the hox+
flash the rom, flash the boot image, boot, reboot into recovery, SIDELOAD gapps and that should work. use cm10 for the moment, as cm11 has an annoying system ui crash loop bug.
Thanks again for your clear and helpful pointers that got me out of a mess, I seem to have figured it out, downloaded the latest CM11 update and extracted boot.img for separate flashing and it all worked, then added gapps and seems working good now (except for dead touch zone from kids dropping it too many times probably!). The OTAs clearly don't work as is and CM probably should update their instructions and how they push major updates that need a new boot.img. Now to work out what to do with my spare phone...!
Sent from my A0001 using XDA Free mobile app
ahighfield said:
Thanks again for your clear and helpful pointers that got me out of a mess, I seem to have figured it out, downloaded the latest CM11 update and extracted boot.img for separate flashing and it all worked, then added gapps and seems working good now (except for dead touch zone from kids dropping it too many times probably!). The OTAs clearly don't work as is and CM probably should update their instructions and how they push major updates that need a new boot.img. Now to work out what to do with my spare phone...!
Sent from my A0001 using XDA Free mobile app
Click to expand...
Click to collapse
The phone will boot loop, as the kernal is different to the rom
Quick fast post. Fix it up later.
Unofficial TWRP for the SM-G360T1
Step 1:
You should know how to flash twrp by now.
Step 2:
Profit
Download link:
https://www.androidfilehost.com/?fid=24052804347820600
Known issues:
Usb otg not working. Will fix later.
Enjoy. Hit thanks or donate and all that good crap [emoji14]
Mine
THANK YOU ONCE AGAIN @ShinySide!!! Not only for root, but now for a working custom recovery. Truly the 2 most important tools we could have for our phone.
FOR EVERYONE ELSE:
As usual, be sure to give @ShinySide your Thanks/Donations/etc.!!! He deserves it! Also, now that you have TWRP you might be wondering what to do next. Here are a couple of suggestions of things that I've already done and that I am quite happy with.
1) Theme it! - Here are some themes you can try out that will not only make TWRP more beautiful, but also provide a layout that is more intuitive and user friendly. These are listed in a Galaxy S2 thread yes, but I've attached a picture of the one that I'm currently running and I'm happy to say that it works on our phone like a charm. I've also used these themes on other phones in the past. Just follow the instructions in the OP of that thread and give the guy some thanks on that thread if you like them. There is no risk in this btw. Either it works or it doesn't and to get rid of it if you don't like it you just have to delete the theme folder that you placed in TWRP. (Try to use the files that say "480x800" as that's the resolution of our screen.) Here is the link: http://forum.xda-developers.com/galaxy-s2-plus/themes-apps/theme-materialised-t2933979
2) Add the Xposed Framework - Go to this link here: http://forum.xda-developers.com/showthread.php?p=62377731
Then, install the Xposed app from the link on that thread. After that, you're going to want to pick the file attached to the OP of that thread that is called "xposed-v80.0-sdk22-arm-custom-build-by-wanam-20160211.zip" and save it to the root of your external SD card. (Do not download the one that says "ARM64" in it. Just the one I mentioned.) Then, just flash it via TWRP and reboot. You should now have the Xposed Framework installed. Once, again be sure to give the OP thanks on that thread too!
NOTE: After flashing Xposed it may hang on the MetroPCS screen on the next reboot for up to 15-20 mins or so while it's doing stuff. If it's any longer than that, then just pop the battery out and reboot. It will boot properly after that while it reoptimizes some apps.
OK something not right everytime I flash the twrp I keep getting the 2.8.70 instead of the version of This 2.8.1.0 one I need help cause everything is correct I keep getting that old version instead of this new version but twrp 2.8.7.0 still works good but I want the version right here
Deandre7452 said:
OK something not right everytime I flash the twrp I keep getting the 2.8.70 instead of the version of This 2.8.1.0 one I need help cause everything is correct I keep getting that old version instead of this new version but twrp 2.8.7.0 still works good but I want the version right here
Click to expand...
Click to collapse
2.8.7.0 is right. The picture I attached of my themed one I just downloaded from the theme thread because I couldn't take a screenshot from TWRP. Everything is good. No need to worry.
Thanks....glad to know that but everytime I reboot to system from twrp it keep going right back to the twrp instead of system that's what I worry about I have to keep flashing the kernel root cause the twrp not working right but ima get the theme to see what happens next
Deandre7452 said:
Thanks....glad to know that but everytime I reboot to system from twrp it keep going right back to the twrp instead of system that's what I worry about I have to keep flashing the kernel root cause the twrp not working right but ima get the theme to see what happens next
Click to expand...
Click to collapse
It shouldn't be doing that. Also, you should just make sure your TWRP is properly installed first before you do anything else to it. Maybe try rebooting your phone just by holding the power button once instead of selecting reboot system and see if it boots correctly then.
Sent from my SM-G360T1 using Tapatalk
I don't think it's right now I have the same picture frame u have in the picture but still not 2.8.1.0 at the top it have the 2.8.7.0 up there at the top of it and another thing is I can't flash anything everything else good but can't swipe to install so I need to get this right cause I don't be having problems with nothing else when I do stuff for my device
Deandre7452 said:
I don't think it's right now I have the same picture frame u have in the picture but still not 2.8.1.0 at the top it have the 2.8.7.0 up there at the top of it and another thing is I can't flash anything everything else good but can't swipe to install so I need to get this right cause I don't be having problems with nothing else when I do stuff for my device
Click to expand...
Click to collapse
Again, it is supposed to be 2.8.7.0 . Don't go by the picture I posted it was just a sample of what I had. Not a screenshot. Also, it doesn't need to look like mine to work. Theming it was just for fun and should only be done after you've successfully installed TWRP. Anyhow, try flashing this stock recovery file here. Then, boot into stock recovery and make sure you can still reboot to Android from there. If so, then go back and try flashing the TWRP recovery file again instead and see if that fixes the problem. No one else should flash this file by the way unless they are trying to go back to stock recovery for whatever reason. Thanks!
Sent from my SM-G360T1 using Tapatalk
Good job
Awesome! Goood job dude, can't wait till you write up the proper instructions. I'm a noob so don't want to do something wrong.
Another masterpiece By @shineside....
A great BIG Thank you @Bogarty For helping to bring this all together.
We have root, we have TWRP, and that's all thanks to @ShinySide! Great work!
Ok yall I just did a splash screen if anyone don't know but everyone have the color theme already go to the page here http://forum.xda-developers.com/android/themes/theme-twrp-materialised-dark-light-play-t2915584 scroll down to the change the recovery splash screen download the AIK file First when it finish flash it before anything download the splash set zip when it finish unzip that file then u download the trap kernel root are if u already have it on the device use any root explore renamed the tar.md5 to .img now go to recovery flash that AIK before you start anything hit where u change your theme color but click on change splash then u put the trap kernel.img on the first slot then the second slot click inside the splash set folder choose what color u want then flash it then there u go a new splash screen set......this for anyone that don't know
bogarty said:
It shouldn't be doing that. Also, you should just make sure your TWRP is properly installed first before you do anything else to it. Maybe try rebooting your phone just by holding the power button once instead of selecting reboot system and see if it boots correctly then.
Sent from my SM-G360T1 using Tapatalk
Click to expand...
Click to collapse
So, should this NOT work and it continues to reboot to TWRP what comes next? ? Ok, you got me. It continues to reboot into TWRP. I've never encountered this scenario before (granted I've never flashed a custom recovery via ODIN before either, but it went as expected up until I did a backup and tried to reboot into the system) and no, I didn't bother with trying to fancy up TWRP. I don't want TWRP looking unfamiliar. Any help would be greatly appreciated.
i am oblivion said:
So, should this NOT work and it continues to reboot to TWRP what comes next? Ok, you got me. It continues to reboot into TWRP. I've never encountered this scenario before (granted I've never flashed a custom recovery via ODIN before either, but it went as expected up until I did a backup and tried to reboot into the system) and no, I didn't bother with trying to fancy up TWRP. I don't want TWRP looking unfamiliar. Any help would be greatly appreciated.
Click to expand...
Click to collapse
Try flashing through ODIN again. Make sure you are in actual download mode (meaning don't use the option in TWRP, use the key combo), and flash it again.
Maybe we could get another youtube video? What do you say, "TheDerek"?
xRaZeR_FuZioNx said:
Try flashing through ODIN again. Make sure you are in actual download mode (meaning don't use the option in TWRP, use the key combo), and flash it again.
Click to expand...
Click to collapse
Ok, that's next on the agenda. Gonna take a walk and get myself calmed down before I resume troubleshooting. Thanks for the helpful and speedy response. And the bit about booting into Download Mode using the button combo over the TWRP option - I actually had no idea there was a difference there. I've gathered several boot/recovery zips and tars just in case and am tracking down the T-Mobile version of the g360t1 firmware as well (to cover all my bases, because when it rains it pours ?). Anyhow, I'll report back once I have something to report and thanks again guys ?
i am oblivion said:
Ok, that's next on the agenda. Gonna take a walk and get myself calmed down before I resume troubleshooting. Thanks for the helpful and speedy response. And the bit about booting into Download Mode using the button combo over the TWRP option - I actually had no idea there was a difference there. I've gathered several boot/recovery zips and tars just in case and am tracking down the T-Mobile version of the g360t1 firmware as well (to cover all my bases, because when it rains it pours ?). Anyhow, I'll report back once I have something to report and thanks again guys ?
Click to expand...
Click to collapse
i am oblivion said:
So, should this NOT work and it continues to reboot to TWRP what comes next? ? Ok, you got me. It continues to reboot into TWRP. I've never encountered this scenario before (granted I've never flashed a custom recovery via ODIN before either, but it went as expected up until I did a backup and tried to reboot into the system) and no, I didn't bother with trying to fancy up TWRP. I don't want TWRP looking unfamiliar. Any help would be greatly appreciated.
Click to expand...
Click to collapse
It has to be something you guys are doing during the flashing process that is causing it to boot into TWRP instead of Android. I would try flashing the Trapkernel again from download mode to see if that gives you boot, then if so, try flashing TWRP again. Both should be flashed in AP slot of ODIN. Make sure OEM Unlocking is checked in developer options, etc.
If that doesn't work and it still boots to TWRP, then you may have messed something up in there somehow. Try flashing back stock boot and stock recovery and make sure boot and stock recovery were restored. Once that's working, then you can try reflashing Trapkernel and TWRP. Use this link for more info on restoring your phone and for links to the stock files if you need them.
http://forum.xda-developers.com/showthread.php?p=62906680
Sent from my SM-G360T1 using Tapatalk
Theres a problem, I cant moutn system in Twrp and because of that i cant update SU binary and some apps dont work :/
cmurder61 said:
Theres a problem, I cant moutn system in Twrp and because of that i cant update SU binary and some apps dont work :/
Click to expand...
Click to collapse
Try reinjecting TWRP using the option in settings.
Hi guys. I've had a rooted S3 for a while and have flashed loads of roms. Few months ago the phone started acting strangely and the only Ron I could get to work was the German version of the original KK. Now, even though the device is still rooted any attempt to flash another room will give a "signature not verified" error. Anyone else come across this?? Cheers
Hamsterboy2000 said:
Hi guys. I've had a rooted S3 for a while and have flashed loads of roms. Few months ago the phone started acting strangely and the only Ron I could get to work was the German version of the original KK. Now, even though the device is still rooted any attempt to flash another room will give a "signature not verified" error. Anyone else come across this?? Cheers
Click to expand...
Click to collapse
Do you use odin to flash roms or custom recovery??
Custom Recovery... TWRP. Think using Odin might yield some results?
Thanks for the reply btw ?
Hamsterboy2000 said:
Custom Recovery... TWRP. Think using Odin might yield some results?
Thanks for the reply btw
Click to expand...
Click to collapse
You can turn off signature verification in twrp it should do the trick bro hit the tnx button if I helped you
Oh cool. Didn't spot that. Using ROM Manager so will have a look at the options. Cheers
Hamsterboy2000 said:
Custom Recovery... TWRP. Think using Odin might yield some results?
Thanks for the reply btw ?
Click to expand...
Click to collapse
Be sure you haven't a borked version of TWRP. I think official 2.8.7.0 is borked.
Try a more recent unofficial one or use Philz touch 6.48.4 instead for instance.
If your recovery is OK, just check options inside twrp recovery about signature verification... Un-tick zip signature verification.
Btw, about root, AFAIK you can flash custom recovery and custom ROMs without being rooted.
You were right. Switched to CWR and it's all good. Cheers.....