Hello everyone!
I am looking for something special, it's bugging me that no flip case I've found got a cutout for the LED light in the top left corner of the phone.
I've tried to make one on my own by drilling a hole in the case I've got and put a little plastic tube in there to get the light through it. It was good but then again, it's not factory made and it doesn't look that good as I wished for. Then I just cutout a piece of the top left corner of the flip case and again, it looks aweful but it does the job.
So my question is, are there any flip cases out there that got a little hole for the LED light? It would be great if it were an S-View cover as well but it's okay if it doesn't have S-View.
Additional question: Does anyone of you got the Spigen S-View flip case? If so, is the front made out of metal or plastic? I'm thinking about buying one and then drilling a better hole since metal is easier to handle than plastic.
Thanks in advance, BunnyPig!
BunnyPig said:
Hello everyone!
I am looking for something special, it's bugging me that no flip case I've found got a cutout for the LED light in the top left corner of the phone.
I've tried to make one on my own by drilling a hole in the case I've got and put a little plastic tube in there to get the light through it. It was good but then again, it's not factory made and it doesn't look that good as I wished for. Then I just cutout a piece of the top left corner of the flip case and again, it looks aweful but it does the job.
So my question is, are there any flip cases out there that got a little hole for the LED light? It would be great if it were an S-View cover as well but it's okay if it doesn't have S-View.
Additional question: Does anyone of you got the Spigen S-View flip case? If so, is the front made out of metal or plastic? I'm thinking about buying one and then drilling a better hole since metal is easier to handle than plastic.
Thanks in advance, BunnyPig!
Click to expand...
Click to collapse
I ditched my flip case for a wallet/card holder/media stand by Cellairis.
Related
hi i want some suggestions to buy a case in which i can fit the cingualr 8525 with the extended battery ?
seems like no one here is using the phone with extended battery and putting it in the case
I'm wondering the same thing!
there's a reverse clip holder in the case recommendations thread, it's not a complete case though as it only covers the front portion of the phone. would prefer a better solution though.
No
Your best bet would be to get this:
http://www.boxwave.com/products/activecase/active-case-cingular-8525_2110.htm
Use the top piece to protect your phone and for the bottom piece, you could color the deminsions with a marker on the case, then use a coat hanger, hold it under a fire (such as on a gas stove) until its red hot, then burn through the case and follow the lines you made through, until the panel is off, allowing the battery to poke out through the case. It would be risky, take alot of time but its worth it. If you want you can test it with this case, but I dont recommend this case at all, its cheap and its belt holster is garbage:
http://www.meritline.com/trans-smoke-cover-for-htc-8525.html
Sonic I just received the $4.99 black case. I will try your method now. Thanks.
Hehehe I messed up the case. For some odd reason the bottom piece won't lock into the cell phone. I'm going to look for a silicone black skin so I would just cut out the piece with a knife or something...
EDIT: My next victim http://cgi.ebay.com/Silicone-Case-D.../newreply.php?do=newreply&noquote=1&p=1246393
Reply8673QQrdZ1QQssPageNameZWD1VQQcmdZViewItem
Hi, just wanted to let you guys known the rubber/silicone whatever thingy it is worked. Only took me like 5 mins to cut the piece of with a xacto knife.
Yea, but don't you find the rubber impeads the sliding keyboard? I have the rubber too but i don't use it because of that.
tallshorty said:
Yea, but don't you find the rubber impeads the sliding keyboard? I have the rubber too but i don't use it because of that.
Click to expand...
Click to collapse
Nope I haven't had that problem. Only thing problem I got so far is that the front cover comes often.
Just ordered the Krusell flip case and then got the belt clip to go with it.
If you have any questions about these items then feel free to ask away and I'll tell you as much as I can as soon as it arrives.
Case (Tried to add link but not allowed to yet so copy and past the below into ebay and you'll find them)
KRUSELL MULTIDAPT LEATHER SWIVELKIT SWIVEL KIT 45 45MM BELT CLIP FOR CASE ORBIT
Clip
KRUSELL MULTIDAPT LEATHER SWIVELKIT SWIVEL KIT 45 45MM BELT CLIP FOR CASE ORBIT
Recieved my Krusell case the other day and its excellent in almost every way. The build quality is fantastic an even has that luxurious leather smell to it. Very strong and sturdy/well made case.
Flip cover folds downwards and can be slid off as well. I thought I wouldn't use the detachment feature but I use it all the time if I'm handling the phone a lot. You could even use the case completely without the flip cover and it would give you better protection than an Imak case (which I had first off).
It also has the option of a belt clip - which can be removed and Krusell has a lot of useful and different styled attachments. It comes with a alegator type belt clip that connects to the phone by a round plastic button attached to the case and this clip is a non swivel model - great for normal sized belts (thin/narrow).
I wear a combat style belt for work so I ordered the 45mm belt clip which slides onto the belt and can not come off without taking the belt off. The clip is a swivel clip and it clips in and holds super well.
Protects the phone very very well - there are holes etc but its made in such a way that its very hard for surfaces to come in contact with the phone at all. If you dropped the phone in this case it would be very well protected.
The cover looks as though it would probably outlive the phone.
The inside of the case is a soft suede leather which means that any dust or dirt getting in between the phone and the case is not going to act like sandpaper as in the hard cases - ie no scratching.
The only thing I noticed after a couple of days use is the the case loosened up slightly and the phone would move approx 1-2 mm out towards the top of the case making grabbing/sliding down the blind hard to access. I solved this by some double sided tape inside the case. I peeled off one side of the tape and stuck it to the inside of the case then slid the phone in and then gently pulled the case away from the phone and pulled the other side of the tape off with some tweezers and then pushed the case together - now the phone doesnt slide anywhere and is securely stuck inside the case and all the button/mic/camera holes line up perfectly.
Highly recommended and worth considering even if your thinking about an Imak style case because you can remove the clip button and the flip face and you have a similar but better case all round - the only drawback is possibly the price but compared to the price and capabilities of this phone I didnt think it too bad, especially if you work in moderate to extreme conditions.
What do you mean the flip part can be left off? Pics?
It slides off from where it attaches on the back of the case. I'll get some pic's at some point.
Photo's
SCHUMI_4EVER said:
What do you mean the flip part can be left off? Pics?
Click to expand...
Click to collapse
View pic's.....
more pic's
Oh wow cool. I didn't know it could do that. Looks like it leaves the top right corner exposed though.
SCHUMI_4EVER said:
Oh wow cool. I didn't know it could do that. Looks like it leaves the top right corner exposed though.
Click to expand...
Click to collapse
I spose it does leave it a little "exposed" but this is so you can use the front facing camera and light sensors etc and even so its only a couple of mm and the leather on top of it is quite thick so to get something to touch that part of the phone I either have to aim the object at it or hold the phone at a 45degree angle to rub the plastic on the table. But then again with the flap on its covered by the clip strap.
http://www.ebay.com.au/itm/KRUSELL-..._MobilePhonesCasesPouches&hash=item2a102e5e80 <- this is the case yeah?
electricbluejase said:
http://www.ebay.com.au/itm/KRUSELL-..._MobilePhonesCasesPouches&hash=item2a102e5e80 <- this is the case yeah?
Click to expand...
Click to collapse
Yip thats the one.
Link
Alright, The case the box came is in is kind of girly, anyways the quality of the case is amazing! It doesn't feel like it was cheaply made at all. It doesn't add too much bulk and I can still fit it in my skinnys(Levi's 511 Skinny 29 x 30) front pocket. The buttons are easily accessible even the the volume button being covered by the front flap it is still easy to press / locate since the case has a steep cut out for the volume buttons. Aswell as the S-Pen being so easily accessible. An added perk i liked about this case is that the speaker hole is actually covered by its own mesh. It also has an accessory hole so you could attach an accessory / lanyard to it. The Magnetized kick stand does not interfere with signal(atleast none i can tell).
Album
Zenus cases are the best I've seen so far for the Galaxy Note. I was thinking of getting this one as well but the color combinations just don't do it for me. Also, there's not cutout for the front speaker so it would be a little awkward to have to hold the front leather part back every time. I like that the case clips onto the metal part on the side and doesn't rest on the top of the phone so that a screen guard will thankfully be left untouched. I also love that it has a stand (The only reason I'm not getting the Zenus Masstige Stripe Case). I was wondering though, when the stand is set up, does the little latch (idk what it's called lol, the little thing used to clip on to the front cover to close the case) hide a little part of the screen since presumably, it'll be hanging down a little bit?
EDIT: Ordered it lol. It may have its flaws but it's the best I could find at its price range.
I have one of these (different colors, but this color looks great).
They are extremely high quality. As good or better than Vaja, for instance.
I've posted this before, that make sure you pay more and get the leather ones, as they have a few lines and some of the lines aren't as good quality.
This particular case is just great. The flap is a tad annoying but well worth it overall.
Note: one thing worth mentioning is that they are very light also.
would it be okay to use this case with a FULL skin applied? Ie. sides and back??
i'm sure the front would be okay, but just wanted to see if the sides of the phone with skin be okay.....
i've been looking at cases that have the flip cover, but they all look like it would peel off the side skins..... this one looks like it like it might be okay.
predation said:
would it be okay to use this case with a FULL skin applied? Ie. sides and back??
i'm sure the front would be okay, but just wanted to see if the sides of the phone with skin be okay.....
i've been looking at cases that have the flip cover, but they all look like it would peel off the side skins..... this one looks like it like it might be okay.
Click to expand...
Click to collapse
Hmmm...that's a tricky one. Obviously, it clips in tightly and securely so it might damage the skin during insertion and removal but once it's sitting in there, as long as you don't constantly remove it, it should be fine. I would recommend going to a store and testing out either this case or similar leather cases, but then again, if you harm the skin in the process, then this whole discussion is useless lol. On another note, why use a skin? The note is such a beautiful sleek beast. I wouldn't want to hide away any of the sides or take away from the beautiful protruding glass. That's why I hate my current Capdase Jacket XPose and am going for this case. Just increases the beauty XD. Anyways, yes, back on topic, I wouldn't recommend using a skin with this cover but hopefully someone who's actually tried it will reply.
Side-note: I ordered the Wine-Red / Dark Brown version
predation said:
would it be okay to use this case with a FULL skin applied? Ie. sides and back??
i'm sure the front would be okay, but just wanted to see if the sides of the phone with skin be okay.....
i've been looking at cases that have the flip cover, but they all look like it would peel off the side skins..... this one looks like it like it might be okay.
Click to expand...
Click to collapse
Here's a Flip case that would most likely not interrupt your skin.
Link
xCeejayy said:
The aluminum bumper wasn't doing it for me so I was looking around and I found this case. The colors are pretty subtle and calm. I'll update this with a review / pics of the case on when I receive it. I just wanted to share this case with you because it just looks so nice.
Link
Alright, The case came in the box it comes in is kind of girly, anyways the quality of the case is amazing! It doesn't feel like it was cheaply made at all. It doesn't add too much bulk and I can still fit it in my skinnys(Levi's 511 Skinny 29 x 30) front pocket. The buttons are easily accessible even the the volume button being covered by the front flap it is still easy to press / locate since the case has a steep cut out for the volume buttons. Aswell as the S-Pen being so easily accessible. An added perk i liked about this case is that the speaker hole is actually covered by its own mesh. It also has an accessory hole so you could attach an accessory / lanyard to it. The Magnetized kick stand does not interfere with signal(atleast none i can tell).
Album
Click to expand...
Click to collapse
These Zenus cases look great and seem very usable. But the downside is that they have a magnet at the back that interferes with S-pen functions (not with the signal). Check in the screen area in front of the magnet by trying to draw several long thin lines with the SPen that cross this area. That case was a money waste for me...
drkalo said:
These Zenus cases look great and seem very usable. But the downside is that they have a magnet at the back that interferes with S-pen functions (not with the signal). Check in the screen area in front of the magnet by trying to draw several long thin lines with the SPen that cross this area. That case was a money waste for me...
Click to expand...
Click to collapse
I tried this and it works fine for me Maybe contact Zenus for another one?
xCeejayy said:
I tried this and it works fine for me Maybe contact Zenus for another one?
Click to expand...
Click to collapse
I got these symptoms after a couple of days usage. I contacted the dealer and got a substitute with Capsule Stand Slide Series - White / Lime
When I got my Note off CL came with the Eel leather case. It's slick but I wish it was the capsule.
Sent from my SAMSUNG-SGH-I717 using xda premium
Ok here is the deal.
I normally use a gel case on my phones. There fit the phones well and cover everything that needs to be.
But they make the phone a lil bit thicker and hide the phone. Normally I get a phone and want to see it for itself.
Well I brought a metal bumper and it looks nice.
But I see that the camera sticks out and touchs when sitting it down.
My girl says that the camera screen is glass and won't break or scratch, but I still like for the phone to not sit on it.
So I am wondering if there is anything I can put around the camera to protected.
I was thinking of something like a form pad so the camera wouldn't touch but idk.
I know some will say get one of the charger back but then it makes the phone thick and defeats the point.
Whole new lens cover assembly cost about $6 on e-bay and shouldn't be difficult to DIY, but you could get some small piece of thick one sided foam tape, cut it to shape and stick around the cam, why not. If it gets dirty or comes off, make new one. Personally I have not seen anything like that commercially, wait, actually there is lens mount you can glue around cam, it comes with small tele lens that you can attach on top.
pete4k said:
Whole new lens cover assembly cost about $6 on e-bay and shouldn't be difficult to DIY, but you could get some small piece of thick one sided foam tape, cut it to shape and stick around the cam, why not. If it gets dirty or comes off, make new one. Personally I have not seen anything like that commercially, wait, actually there is lens mount you can glue around cam, it comes with small tele lens that you can attach on top.
Click to expand...
Click to collapse
Yea I saw the replacements on eBay for like $10ship and I'm a tech person so I can replace it no problem.
And I didn't thing about the lens. I know they have a metal ring.
I'll check into everything.
Thanx.
I have a metal bumper also. I had an extra home button sticker that I sticked near the camera lens. Now when I lay flat down it doesn't lay on the camera lens.
Sent from my SM-N9005 using Tapatalk 2
I use skinomi clear skin. They include a skin for the bottom half of the camera. When my phone is laying flat the lens doesn't touch. As a bonus since you're using a metal bumper, the side skins can act as an all around protection between the bumper and the chrome trim. Much better than what the bumper comes with. But you will probably need to remove the ones on the bumper first as it will become too thick and the bumper won't fit properly.
Sent from my SM-N900T using Tapatalk
I am updated to Kitkat,unrooted. so s-view no work for me. Thats why I took the front flap of my white spigen slim armor view out, and let the back side on on white note3 ... gives it some kind of a z10-ish look.
coming back to the point, my case does the job well, apart from protecting the sides from scratches, by keeping the camera lens from having contact when lying flat. well, quite a hefty investment if you want to protect your lens only. but since I already purchased it, it does the job decently, and I dont find it that much of bulky. anyhow, bulky or not, to me - this is a question of habit. i mean, now that I look and take a grasp of my old i9100, it seems very small now, which wasnt the case some months back my two cents
Nitish
N1T15H said:
I am updated to Kitkat,unrooted. so s-view no work for me. Thats why I took the front flap of my white spigen slim armor view out, and let the back side on on white note3 ... gives it some kind of a z10-ish look.
coming back to the point, my case does the job well, apart from protecting the sides from scratches, by keeping the camera lens from having contact when lying flat. well, quite a hefty investment if you want to protect your lens only. but since I already purchased it, it does the job decently, and I dont find it that much of bulky. anyhow, bulky or not, to me - this is a question of habit. i mean, now that I look and take a grasp of my old i9100, it seems very small now, which wasnt the case some months back my two cents
Nitish
Click to expand...
Click to collapse
Yea i got a normal gel case for the phone. I have always use those without problems but i got a bumper for the note 3. It just feels better, so trying to keep the phone slim.
I thought about putting a dot of hot glue somewhere around it to lift it up. But i just didnt wanna do that to a new phone.
I want a square that would fit right around the camera and stick to the back plate.
Ill keep looking
the replacement lens piece is like $10, just something to think about
I've loved my Poetic case, it's a real winner in my opinion, but last night, sitting on the couch, I felt a rough corner and on examination found the plastic had cracked and fell off in my hand.
I've never dropped my tablet. The piece that broke off was near the speaker and it's relatively thin there.
I sent in for an RMA, hopefully they will just replace it.
Has anyone else had this issue?
Only issue I have with the case is it would be nice if it had a 2nd hole for the camera on the front so when the front is folded all the way back you could still take pics.
mknewman said:
Only issue I have with the case is it would be nice if it had a 2nd hole for the camera on the front so when the front is folded all the way back you could still take pics.
Click to expand...
Click to collapse
You can do this hole itself. It's not so hard.
Find some pen or ballpoint which one have metallic body and this body is with needed diameter. unscrew the body to pieces. Now take off the case, place on some cutting board. Measure the correct place where the hole must be and measure again three times. Take the small hammer and with this metal body make the hole, hammering once or twice. It cuts good hole.
Actually i'm not familiar with this case material but for some materials you can heat the pen metal body.
And yes, you can use any small metal pipe which size is for you needs.