When you flash wrong rom or flash wrong file stock lg g2 :
Hand logo lg
No downloadmod
No fastboot
security error
Qualcomm 9006
Ok you need short testpoint lg g2 phone put qualcomm 9006 show very partitiont or short testpoint qualcom 9008 then use tool boardiag of my unbrick.
http://forum.xda-developers.com/lg-...9008-board-t3072073/post59949117#post59949117
How do short testpoint Lg g2 you need remove backcover
https://www.youtube.com/watch?v=nYTmTZkbfmU
Guid short testpoint
https://www.youtube.com/watch?v=8ZD98phYTsM
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then short testpoint in picture
With qualcomm 9006 when install driver done (qhsusb_bulk) read video of him
https://www.youtube.com/watch?v=_d5b_osUTug
When flash done but phone normal not save. OK you need check model in front back board see pictrure
I think model wrong, lg g2 d802 but main board d800
You need unbrick file d800
then flash tot d800 done.
I short this point in picture below then use [TOOLS] SRK Tool 2.0.2 [ROOT/UNBRICK/UTILITY/BACKUP]- 20150503 to fix.
My story in my page https://www.facebook.com/droidth/posts/772287019556649
The original thread is always online http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
somboons said:
The original thread is always online http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
Click to expand...
Click to collapse
But not full guide and very hard user can not do.
Related
my phone is hard brick but can access download mode and fastboot
how can i do
FASTBOOT : i flash system image with fastboot but it too big file
LG FLASH TOOL : wm_progress_fail:crying:
SMART FLASH TOOL : wm_progress_fail:crying:
LG SUPPORT TOOL : can't flash becouse program is update it self i can use offline update
i bought it from US but now am i thailand i don't want to go to lg service
Q : How can i do i can't flash system.img via fastboot it too big
can i flash recovery via fastboot (locked bootloader)
BIG UPDATE
MY PHONE IS FREE NOW
becouse i use this script it force link lg support tool to update phone not link to mainscreen ^^
https://mega.co.nz/#!UM1TmYoZ!auGWNjfvaR_YgHJMHx-E-M5sz8Pm4lmZOeoW1KEE8vI
HELP! Softbrick LG L9-P768
Bro, I have problem on my phone, the model is LG L9-P768, I flash thru temporary CWM a custom rom which is only a patch to a custom rom, now it is stucked in LG Boot logo, if I boot to recovery (Power+Vol.Up+Home), it is locked.. It can go to download mode. When I connect it to PC, it was detected and installed some drivers but the OMAP4430 is not installed and every tool I used like KDZ offline cant detect my phone, it only reaches the 3rd stage of the installation and in 15% of it, it failed and ask me to retry, even after many retries, I failed.. how can I fix this? I hope someone can help me in this problem...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hey Guys i am having some Problem with my lg g2. i was trying to install CloudyG2_3.0 Rom on my device and i got stuck in Fastboot mood. I realize that i couldnt enter Recovery Mode neither Download Mood. :crying:
I then decided to follow a guide that would allow me to get back recovery and download mood. My Computer Recognized my ABD so i was able to erace and flash LS980 zvc_partitions Via Commands.
I Was now able to Get into Recovery mood and Download mood. But the problems i dont know if i flashed the correct Partitions because in in download mood i am not able to flash any stock room. The .ToT method neither the .KDZ method.
maybe i flash the wrong Download mood and recovery cause when i tried flashing it the TOT metohd the software said my phone is model F320s but none of those roms is flashing either. All my drivers is installed.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
please help .
open ur back cover n see which model it is.
thhen flash the right recovery to it.
Okay i was Able to open the back cover and this is what i see. Can anyone Guide me To how i should go on from here ?
mkeeoma said:
Okay i was Able to open the back cover and this is what i see. Can anyone Guide me To how i should go on from here ?
View attachment 3261553
Click to expand...
Click to collapse
It's LS980 means Sprint U.S. Model.
flash one file from here
zvc recommend
http://storagecow.eu/index.php?dir=Xda/LG+G2/Stock/Sprint/
tutorial from here TOT Method!
http://forum.xda-developers.com/showthread.php?t=2432476
if it says wrong model then u may need this
http://forum.xda-developers.com/sprint-g2/general/dll-to-bypass-lg-flash-tool-model-check-t2990665
**************Flashing Hard Bricked Redmi 3 SnapDragon***********
This IS the Guide to Flash hard Bricked Redmi 3, using Deep flash mod, No Fastboot, No Edl, No Test point, very easy and simple, Hit :good: if this helpful for you,
Instructions-
First of all Prepare Deep Flash Cable using Below Guide
Attached Both Coper Wire and then connect this cable with your pc
Now connect your Device to usb [Make Sure Your phone is switched Off]
On Pc go To Device manager and Look on port, {No Available] Don't Worry]
Pull the attached Wire and look Device Manager a New port Is Available HS-USB Diagnostic 9008[ com5, com17 etc]
Ok your Device is ready For Flashing
Run mi Flash click on Browse and Load Fastboot Rom Folder
Click Refresh and Then Flash Done, wait a few Seconds While flashing IS complete ,
Done,
Bought a Deep Flash Cable @ AliExpress (for about 5€/5US$). It has a button to enable Qualcomm HS-USB QDLoader 9008 and for me is more secure then trying to risk to kill your mainboard via USB.
P.S.: I'm not good at DIY.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
plz sent me a cable at my village, lol, Delivery system Not Available For all Areas or this guide for that person,
Does this work with Redmi Pro?
Hi all,
Can someone give me a list with gparted from a D620r? I need partiton start-end block, size, etc. I bricked my phone, and now dead(it just shows qdloader 9008 without disks when i short emmc pins on the mainboard and connect usb, no way to enter other modes) I want to flash the phone with BoardDiag,i got partitions.txt format, just need the values from the phone..
Thank you for everyone who helps me!!!
Here you can find sizes: https://github.com/LineageOS/android_device_lge_g2m/blob/cm-14.1/BoardConfig.mk#L42-L48
Boardconfig
mobiusm said:
Here you can find sizes: https://github.com/LineageOS/android_device_lge_g2m/blob/cm-14.1/BoardConfig.mk#L42-L48
Click to expand...
Click to collapse
Hi,
Whoa, TARGET_OTA_ASSERT_DEVICE := g2m,g2mds,g2mss,d620,d618,d610 It seems that is the same with others. Thank you, big help, btw i need start and end size of all blocks.(including modem , etc, that is not there )
"Architecture of partition.txt
partition_entries=47
partition_name=PrimaryGPT
start_block=0x0
file_name=PrimaryGPT.mbn
file_size=524288
partition_name=modem
start_block=0x8000
file_name=modem.mbn
file_size=55050240"
....
etc..
mman1982 said:
Hi all,
Can someone give me a list with gparted from a D620r? I need partiton start-end block, size, etc. I bricked my phone, and now dead(it just shows qdloader 9008 without disks when i short emmc pins on the mainboard and connect usb, no way to enter other modes) I want to flash the phone with BoardDiag,i got partitions.txt format, just need the values from the phone..
Thank you for everyone who helps me!!!
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hello im trying to unbrick my phone using testpoint method but once i disassembled my phone the insides look different the from the guide i was following i managed to find an image showing where the pins are on my phone but they are not there. Instead there are lots of other pins around. Can someone please help me with this? I will post image of how my phone looks like (You cant rly see it but there are no pins where there are supposed to be instead there's only a straight copper like line).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thank you i getting desperate...
Seems like you are using The MTK version of Redmi Note 3 (judging by the SIM card pin) Unfortunately, Mediatek phones do not have testpoint pin.
hasel17 said:
Seems like you are using The MTK version of Redmi Note 3 (judging by the SIM card pin) Unfortunately, Mediatek phones do not have testpoint pin.
Click to expand...
Click to collapse
Well that sucks... so any idea how do i unbrick MTK version?
Peaceleaf said:
Well that sucks... so any idea how do i unbrick MTK version?
Click to expand...
Click to collapse
Download the fastboot ROM, disconnect ur battery and then plug ur phone in the computer, download SP Flash tool and select the files from the fastboot and flash it onto try and see if works ?