Hi Guys !!!
I recently Soft Bricked My A311 and it was totally DEAD !!!!!! BUT AFTER TWO DAYS HARD WORK FINALLY GOT IT WORKING TOTALLY FINE FROM DEAD STATE !!!!
FOR BRIEFLY EXPLAINING VIDEOS N SHOWING ACTUAL FLASHING CLICK HERE
When To Use My Meathod :-
1.Not able to flash any ROM (Every Rom Fails)
2.Error Message "Unable to mount /Data" OR "Unable to mount /cache" while flashing Rom
3.Internal Storage Error "No such directory exists "
4.Unable to Boot ur device in any way
The Only Meathod I Suggest Is To Flash Stock Rom Using YGDP tool ........
BEFORE ACTUAL PROCESS FOLLOW THESE STEPS !!!!!
1.First u need to Download Micromax A310/A311 Stock Rom and YGDP tool for for this click on this link -http://androidxda.com/download-micromax-stock-rom-models
2.U need a usb cable with Standard Configuration
3.And Offcourse Ur Bricked Device
Now The Actual Process>>>>>>>
1.Unzip The Download Stock ROM rar into any directory of ur Computer(WINDOWS) and after unziping u will get a file in .CPB Format
2.Install YGDP Tool on the System by clicking next next next but Dont Run
3.Now the most Important and the most Tricky Part To Install The Device Drivers On The System...... If u already have drivers installed then u dont need to do this part...........To do this there r different methods for different OS of windows but i prefer Windows 7.......... steps r given below:
a . Go to start in Windows
b. Right click on computer and open manage
c. Device Manager will open
d. Now remove the battery of ur bricked phone and connect it to the pc via the USB Cable
e. Just on connecting usb cable hold volume down button and quickly press the power button around 10 times for system to detect
f. Then the MT65XXX divers installation will get started on the system
h. When the installtion get finished unplug the usb cable
i. Now again plug the usb cable without battery on device and u will see aditional port in device manager for 3-5 Sec named as MTXXX preloder blah blah
4. Seting Up YGDP Tool:-
a.As Installed Earlier u will see a YDGP shortcut on deskop
b.If it Stops working then dont panic Just go to application setting and set compatibility to windows 7
c.Now on opening it will ask for password ........type 369 in password and press enter
d.then the application will start
e.Now u will see a Config Icon on the left top ........Open it
f.Now a window will open with devices on left and CPB select on right .......
h.Now on right side select 8297W_I01 for A310 and for A311 select 8297W only !!!1
g.Now on right side browse the CPB file in ur system which u got on unziping the stock ROM
h.Click Apply and the CPB file check will start ........it will take aroung 2-5 Min
i.on completion u will again come on the home page ...
j.Now on the left top side of the application u will see Start icon ......click on it
k.Now connect ur bricked device via usb cable without battery and in power off state
l.Now if everything went correct then the Cell 0 icon will change into downloading icon ......it means ur phone is detected
m.Flashing will automatically start and will take around 5min
n. On completion the Cell 0 will become 100%
o. Unplug usb cable
p. REBBOOT DEVICE!!!!!!
CONGRATES UR DEVICE WILL RISE FROM THE DEAD !!!!! ENJOY !!!!!!!
AND DONT FORGET TO HIT THANKS IF I HELPED
not working
amitsharad7 said:
Hi Guys !!!
I recently Soft Bricked My A311 and it was totally DEAD !!!!!! BUT AFTER TWO DAYS HARD WORK FINALLY GOT IT WORKING TOTALLY FINE FROM DEAD STATE !!!!
I WILL UPLOAD A VIDEO ON YOUTUBE OF WHOLE PROCESS SOON
When To Use My Meathod :-
1.Not able to flash any ROM (Every Rom Fails)
2.Error Message "Unable to mount /Data" OR "Unable to mount /cache" while flashing Rom
3.Internal Storage Error "No such directory exists "
4.Unable to Boot ur device in any way
The Only Meathod I Suggest Is To Flash Stock Rom Using YGDP tool ........
BEFORE ACTUAL PROCESS FOLLOW THESE STEPS !!!!!
1.First u need to Download Micromax A310/A311 Stock Rom
a. For A310 Stock ROM ....Download From NEEDROM
b. For A311 Stock ROM .....Download From NEEDROM
2.Now Download YGDP FLASH TOOL from NEEDROM MICROMAX A311 SECTION THERE U WILL FIND THE DOWNOAD OPTION OR SEARCH WEB (JUST DOWNLOAD THE TOOL)
3.U need a usb cable with Standard Configuration
4.And Offcourse Ur Bricked Device
Now The Actual Process>>>>>>>
1.Unzip The Download Stock ROM rar into any directory of ur Computer(WINDOWS) and after unziping u will get a file in .CPB Format
2.Install YGDP Tool on the System by clicking next next next but Dont Run
3.Now the most Important and the most Tricky Part To Install The Device Drivers On The System...... If u already have drivers installed then u dont need to do this part...........To do this there r different methods for different OS of windows but i prefer Windows 7.......... steps r given below:
a . Go to start in Windows
b. Right click on computer and open manage
c. Device Manager will open
d. Now remove the battery of ur bricked phone and connect it to the pc via the USB Cable
e. Just on connecting usb cable hold volume down button and quickly press the power button around 10 times for system to detect
f. Then the MT65XXX divers installation will get started on the system
h. When the installtion get finished unplug the usb cable
i. Now again plug the usb cable without battery on device and u will see aditional port in device manager for 3-5 Sec named as MTXXX preloder blah blah
4. Seting Up YGDP Tool:-
a.As Installed Earlier u will see a YDGP shortcut on deskop
b.If it Stops working then dont panic Just go to application setting and set compatibility to windows 7
c.Now on opening it will ask for password ........type 369 in password and press enter
d.then the application will start
e.Now u will see a Config Icon on the left top ........Open it
f.Now a window will open with devices on left and CPB select on right .......
h.Now on right side select 8297W_I01 for A310 and for A311 select 8297W only !!!1
g.Now on right side browse the CPB file in ur system which u got on unziping the stock ROM
h.Click Apply and the CPB file check will start ........it will take aroung 2-5 Min
i.on completion u will again come on the home page ...
j.Now on the left top side of the application u will see Start icon ......click on it
k.Now connect ur bricked device via usb cable without battery and in power off state
l.Now if everything went correct then the Cell 0 icon will change into downloading icon ......it means ur phone is detected
m.Flashing will automatically start and will take around 5min
n. On completion the Cell 0 will become 100%
o. Unplug usb cable
p. REBBOOT DEVICE!!!!!!
CONGRATES UR DEVICE WILL RISE FROM THE DEAD !!!!! ENJOY !!!!!!!
IF U FACE ANY PROBLEM ANYWHERE AND WHATSAPP ME OR CALL ME EVEN ON 9927445068 BECAUSE I KNOW KI JAB PHONE BRICK HOTA HE TOH KITNE FHATI HE!!!!
AND DONT FORGET TO HIT THANKS IF I HELPED
Click to expand...
Click to collapse
i also bricked my nitro a311.... all checked all the step above.. but it stuck at the entering download mode .. nothing happens after thst..
please help me
I can't install the driver thats my prolem
Help me
Refer this
Ben02 said:
I can't install the driver thats my prolem
Help me
Click to expand...
Click to collapse
bro i had explained in detail .. you can visit it here...
http://forum.xda-developers.com/a310/help/solved-unbricked-a311-a310-nitro-t3187580
got stsuck
A311.. entering download mode... got stuck here help me help me!.. please
bro .. you can try to flash the stock ROM.... I will surely fix the problem... refer the link given in above reply
Thanks for your help. It might be so help ful for everyone
Sent from my Micromax A311 using XDA Free mobile app
My computer didn't detect my a311.So what can I do??? Pls help me...I have vcom,sp tool drivers and more
Sent from my Micromax A311
thanks for the procedure
fails in ygdp @ 83 percent everytime
ygdp tool fails while downloading the cpb
:crying::crying: a311
I m facing a problem. It stuck in 98%. I cant flash the rom. I download the rom and ygdp tool and install drivers successfully. After i choose 8297w for my a311 and select the cpb file. It unzib the file and so on. Then i select start the cell 0 is entered in download mode and stuck in 98%. Please help me buddy
moulishankar said:
I m facing a problem. It stuck in 98%. I cant flash the rom. I download the rom and ygdp tool and install drivers successfully. After i choose 8297w for my a311 and select the cpb file. It unzib the file and so on. Then i select start the cell 0 is entered in download mode and stuck in 98%. Please help me buddy
Click to expand...
Click to collapse
I'm too stuck with the same issue. But I've some what positive progress. It shows in 25 secs the failure message. So please help me too!!
Note: complete history of my case can be found here!
Thanks It works
Thanks for the post it saved me a lot troubles. .Had trouble finding free MT65XX. Please donwlaod it from by searching "SP flash tool + mediatek" mt65xx.
amitsharad7 said:
Hi Guys !!!
I recently Soft Bricked My A311 and it was totally DEAD !!!!!! BUT AFTER TWO DAYS HARD WORK FINALLY GOT IT WORKING TOTALLY FINE FROM DEAD STATE !!!!
FOR BRIEFLY EXPLAINING VIDEOS N SHOWING ACTUAL FLASHING CLICK HERE
When To Use My Meathod :-
1.Not able to flash any ROM (Every Rom Fails)
2.Error Message "Unable to mount /Data" OR "Unable to mount /cache" while flashing Rom
3.Internal Storage Error "No such directory exists "
4.Unable to Boot ur device in any way
The Only Meathod I Suggest Is To Flash Stock Rom Using YGDP tool ........
BEFORE ACTUAL PROCESS FOLLOW THESE STEPS !!!!!
1.First u need to Download Micromax A310/A311 Stock Rom and YGDP tool for for this click on this link -http://androidxda.com/download-micromax-stock-rom-models
2.U need a usb cable with Standard Configuration
3.And Offcourse Ur Bricked Device
Now The Actual Process>>>>>>>
1.Unzip The Download Stock ROM rar into any directory of ur Computer(WINDOWS) and after unziping u will get a file in .CPB Format
2.Install YGDP Tool on the System by clicking next next next but Dont Run
3.Now the most Important and the most Tricky Part To Install The Device Drivers On The System...... If u already have drivers installed then u dont need to do this part...........To do this there r different methods for different OS of windows but i prefer Windows 7.......... steps r given below:
a . Go to start in Windows
b. Right click on computer and open manage
c. Device Manager will open
d. Now remove the battery of ur bricked phone and connect it to the pc via the USB Cable
e. Just on connecting usb cable hold volume down button and quickly press the power button around 10 times for system to detect
f. Then the MT65XXX divers installation will get started on the system
h. When the installtion get finished unplug the usb cable
i. Now again plug the usb cable without battery on device and u will see aditional port in device manager for 3-5 Sec named as MTXXX preloder blah blah
4. Seting Up YGDP Tool:-
a.As Installed Earlier u will see a YDGP shortcut on deskop
b.If it Stops working then dont panic Just go to application setting and set compatibility to windows 7
c.Now on opening it will ask for password ........type 369 in password and press enter
d.then the application will start
e.Now u will see a Config Icon on the left top ........Open it
f.Now a window will open with devices on left and CPB select on right .......
h.Now on right side select 8297W_I01 for A310 and for A311 select 8297W only !!!1
g.Now on right side browse the CPB file in ur system which u got on unziping the stock ROM
h.Click Apply and the CPB file check will start ........it will take aroung 2-5 Min
i.on completion u will again come on the home page ...
j.Now on the left top side of the application u will see Start icon ......click on it
k.Now connect ur bricked device via usb cable without battery and in power off state
l.Now if everything went correct then the Cell 0 icon will change into downloading icon ......it means ur phone is detected
m.Flashing will automatically start and will take around 5min
n. On completion the Cell 0 will become 100%
o. Unplug usb cable
p. REBBOOT DEVICE!!!!!!
CONGRATES UR DEVICE WILL RISE FROM THE DEAD !!!!! ENJOY !!!!!!!
AND DONT FORGET TO HIT THANKS IF I HELPED
Click to expand...
Click to collapse
Great work... and very nice explanation.... keep goingg....
@moulishankar @sugarmurali
What did u do next after YGDP stuck at 98% for A311?
Andy5.1 said:
@[email protected]
What did u do next after YGDP stuck at 98% for A311?
Click to expand...
Click to collapse
Shut down and close computer thats all
someone please help me....i followed all the above steps but not getting success. The moment i click on Start nothing happens, it just says Entering Download mode and nothing happens. Please help me !!!
+91 9920778298 - Please help me !!!
still stuck on micromax logo after flashing 100%
hi please i have flashed rom via ygdp it shows 100% success but when i boot my a311 it stuck on micromax logo and i have also tried factory mode fix but after commanding ADB Shell it promt no device found.. Plz help me thanks in advance
Bricked micromax canvas a 311
My micromax canvas is not detecting in my system, I have installed all drivers manually. Some time it is stuck in bootloop, some times it get booted to a black screen and shows up setting stopped. But I can boot into recovery mode. Some one please tell me how to flash from memory card. No driver like adb or vcom detects my phone. I tried flash using fastboot mode but it is not detected. Please someone tells me a solution
Related
Hello!
I think my MMX Canvas HD A116 has been soft bricked. :crying:
I'd installed DOGE http://forum.xda-developers.com/showthread.php?t=2663763 ROM, and it was working fine. After that I tried to get backup using Nandroid Manager but it was failed. So, I restarted phone in CWM Recovery mode and tried to backup data from there.
But after that, my phone went dead.
Screen starts for few seconds but it is not showing boot logo and even I'm not able to go into recovery mode also!
My PC or SP Flash Tool is also not recognizing phone.
Will USB Jig work for MMX phones? Is there any hope?!
Please help!
try to reinstall the drivers.. and then connect your device through sptools.
kalpesh_36 said:
try to reinstall the drivers.. and then connect your device through sptools.
Click to expand...
Click to collapse
I tried that.
Still not working! :crying:
try this
1. Turn off the phone by
removing battery.
2. Press and hold the Power button along with both the
‘Volume +’ and ‘Volume -’ buttons until the screen
displays two options.(volume keys first then power key .
after 5-10 seconds holding, Then 2 option will appear)
3. Press the ‘Volume +’ button to enter Recovery Mode.
wipe dalvik, data, cache partion. install MIUI or pure xperia
z2(my choice only, you can try any stable rom) from your
memory card.
shivrajsingh said:
try this
1. Turn off the phone by
removing battery.
2. Press and hold the Power button along with both the
‘Volume +’ and ‘Volume -’ buttons until the screen
displays two options.(volume keys first then power key .
after 5-10 seconds holding, Then 2 option will appear)
3. Press the ‘Volume +’ button to enter Recovery Mode.
wipe dalvik, data, cache partion. install MIUI or pure xperia
z2(my choice only, you can try any stable rom) from your
memory card.
Click to expand...
Click to collapse
Thank you Shivraj for replying.
But as I said in earlier post, my phone is not going into recovery mode. As I press "Volume +" button, it goes off. I wish somehow I can at least boot my phone into recovery mode!
Have anyone tried USB jig for Micromax phones?
aryankirtan said:
Thank you Shivraj for replying.
But as I said in earlier post, my phone is not going into recovery mode. As I press "Volume +" button, it goes off. I wish somehow I can at least boot my phone into recovery mode!
Have anyone tried USB jig for Micromax phones?
Click to expand...
Click to collapse
i guess usb jig only works for Samsung phones..but since u r saying that the device does power on for a second...mayb its not completely bricked...try installing the correct drivers..see if that works?
edwardpage said:
i guess usb jig only works for Samsung phones..but since u r saying that the device does power on for a second...mayb its not completely bricked...try installing the correct drivers..see if that works?
Click to expand...
Click to collapse
That right. Even if USB Jig works on MTk, it will also result in rebooting after 2-3 seconds which you are getting after pressing volume + button. You can only install correct MTK drivers and then install stock rom.
Download Flash Tool , Stock ROM AND USB Driver From Above LINK
NOW Create Folder IN Desktop Give It Name "FLASH"
Copy All Downloaded File In Recently Created Folder "FLASH"
Extract 'SP_Flash_Tool_v3.1304.0.119.rar' AND Also Extract Stock ROM File
NOW Open SP Flash Tools Folder AND Double Click ON "Flashtool.exe"
In Flashtool..Click On SCATTER-LOADING(FOUND IN RIGHT-SIDE) AND Select SCATTER File From STOCK ROM'S Folder
Flashtool Automatic Select All IMGs AND FILEs
NOW Completely Turn Off Your Phone
In Flashtool..Click On "DOWNLOAD" Button
Install USB Driver AND Connect Your Device To Computer
If Everything Is Right Then Process Will Start...Wait Till All Progress Completion
After All Process "GREEN CIRCLE" Appear In Center..
DISCONNECT PHONE AND POWER ON...THAT'S ALL
the correct drivers for mediatek is attached below.
Also, the process after "In Flashtool..Click On "DOWNLOAD" Button" , should be:
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Thank you so much! Finally unbricked my MMX A116
shivrajsingh said:
That right. Even if USB Jig works on MTk, it will also result in rebooting after 2-3 seconds which you are getting after pressing volume + button. You can only install correct MTK drivers and then install stock rom.
Download Flash Tool , Stock ROM AND USB Driver From Above LINK
NOW Create Folder IN Desktop Give It Name "FLASH"
Copy All Downloaded File In Recently Created Folder "FLASH"
Extract 'SP_Flash_Tool_v3.1304.0.119.rar' AND Also Extract Stock ROM File
NOW Open SP Flash Tools Folder AND Double Click ON "Flashtool.exe"
In Flashtool.. Click On SCATTER-LOADING(FOUND IN RIGHT-SIDE) AND Select SCATTER File From STOCK ROM'S Folder
Flashtool Automatic Select All IMGs AND FILEs
NOW Completely Turn Off Your Phone
In Flashtool..Click On "DOWNLOAD" Button
Install USB Driver AND Connect Your Device To Computer
If Everything Is Right Then Process Will Start...Wait Till All Progress Completion
After All Process "GREEN CIRCLE" Appear In Center..
DISCONNECT PHONE AND POWER ON...THAT'S ALL
the correct drivers for mediatek is attached below.
Also, the process after "In Flashtool..Click On "DOWNLOAD" Button" , should be:
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Click to expand...
Click to collapse
Thank you soooo much man. You saved my day... :good:
This drivers worked perfectly and with this method, I finally UNBRICKED my Micromax A116 handset.
Use this drivers for using SP Flash tool with MMX A116.
Perfect!
Thank you Shivraj Singh... :good:
aryankirtan said:
Thank you soooo much man. You saved my day... :good:
This drivers worked perfectly and with this method, I finally UNBRICKED my Micromax A116 handset.
Use this drivers for using SP Flash tool with MMX A116.
Perfect!
Thank you Shivraj Singh... :good:
Click to expand...
Click to collapse
Most welcome
shivrajsingh said:
That right. Even if USB Jig works on MTk, it will also result in rebooting after 2-3 seconds which you are getting after pressing volume + button. You can only install correct MTK drivers and then install stock rom.
Download Flash Tool , Stock ROM AND USB Driver From Above LINK
NOW Create Folder IN Desktop Give It Name "FLASH"
Copy All Downloaded File In Recently Created Folder "FLASH"
Extract 'SP_Flash_Tool_v3.1304.0.119.rar' AND Also Extract Stock ROM File
NOW Open SP Flash Tools Folder AND Double Click ON "Flashtool.exe"
In Flashtool..Click On SCATTER-LOADING(FOUND IN RIGHT-SIDE) AND Select SCATTER File From STOCK ROM'S Folder
Flashtool Automatic Select All IMGs AND FILEs
NOW Completely Turn Off Your Phone
In Flashtool..Click On "DOWNLOAD" Button
Install USB Driver AND Connect Your Device To Computer
If Everything Is Right Then Process Will Start...Wait Till All Progress Completion
After All Process "GREEN CIRCLE" Appear In Center..
DISCONNECT PHONE AND POWER ON...THAT'S ALL
the correct drivers for mediatek is attached below.
Also, the process after "In Flashtool..Click On "DOWNLOAD" Button" , should be:
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Click to expand...
Click to collapse
Hello sir pls. Help me. I too want to flash the v5 of stock ROM but i the driver you have suggested below contains nothing.pls help how to proceed ahead.
alex279 said:
Hello sir pls. Help me. I too want to flash the v5 of stock ROM but i the driver you have suggested below contains nothing.pls help how to proceed ahead.
Click to expand...
Click to collapse
They contain drivers only. SP tools and stock rom needs to be downloaded separately.
need help for drivers
shivrajsingh said:
They contain drivers only. SP tools and stock rom needs to be downloaded separately.
Click to expand...
Click to collapse
very much thankful for the reply.... i am having the other 2 but facing problem with only the drivers, going through sp tools...scatter loading...download....no detection of my device... this might be due to drivers. i found nothing in your 11kb drivers. pls suggest me how i can download the correct drivers. pls. if possible elaborate it stepwise(as i m doing it for the first time/newbie)......hope a quick reply from your side
alex279 said:
very much thankful for the reply.... i am having the other 2 but facing problem with only the drivers, going through sp tools...scatter loading...download....no detection of my device... this might be due to drivers. i found nothing in your 11kb drivers. pls suggest me how i can download the correct drivers. pls. if possible elaborate it stepwise(as i m doing it for the first time/newbie)......hope a quick reply from your side
Click to expand...
Click to collapse
Which windows version, u r using??
.....!!!!!
shivrajsingh said:
Which windows version, u r using??
Click to expand...
Click to collapse
Using windows 8 - 64Bit
alex279 said:
Using windows 8 - 64Bit
Click to expand...
Click to collapse
First disable driver signing (Windows 8 users Only)
use this link for tutorial.....
https://learn.sparkfun.com/tutorial...abling-signed-driver-enforcement-on-windows-8
Now extract the mtk universal driver attachment.
1. Open device manager
2. Connect your phone to PC through data cable.
3. New device will appear in device manager for 5-10 seconds only.
4. Quickly right click on newly appeared device and selected update driver.
5. Select drivers from downloaded and extracted attachment.(right click on new appeared device -> browse my computer for drivers-> browse windows 7 drivers i.e. usb2ser_Win764 in extracted folder)
6. It will successfully install driver.
7. Remove data cable from phone and again insert it in phone.
8. SP tools will recognize it and automatically start flashing since you have already pressed download button earlier.
9. Flashing will complete in 3-4 minutes.
Hello many thnx to you for this useful info. Now i have flashed the device successfully.... Pls. if you can help me to swap the phone storage with the external sd card then it would be great help for me. Actually i have tried to do so but some how i bricked the device & that is why i have to flash.... Pls. Sir give me details guide on how to swap memory on canvas HD A116
Sent from my Micromax A116i using XDA Premium 4 mobile app
alex279 said:
Hello many thnx to you for this useful info. Now i have flashed the device successfully.... Pls. if you can help me to swap the phone storage with the external sd card then it would be great help for me. Actually i have tried to do so but some how i bricked the device & that is why i have to flash.... Pls. Sir give me details guide on how to swap memory on canvas HD A116
Sent from my Micromax A116i using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hello friend,
Try this way: http://forum.xda-developers.com/showthread.php?t=2346389
As it works on MediaTek devices and MMX A116 is one of this.
pls suggest me how i can download the correct drivers.
aryankirtan said:
Hello!
I think my MMX Canvas HD A116 has been soft bricked. :crying:
I'd installed DOGE http://forum.xda-developers.com/showthread.php?t=2663763 ROM, and it was working fine. After that I tried to get backup using Nandroid Manager but it was failed. So, I restarted phone in CWM Recovery mode and tried to backup data from there.
But after that, my phone went dead.
Screen starts for few seconds but it is not showing boot logo and even I'm not able to go into recovery mode also!
My PC or SP Flash Tool is also not recognizing phone.
Will USB Jig work for MMX phones? Is there any hope?!
Please help!
Click to expand...
Click to collapse
It had to me once, when I was going to flash the stock rom from SP Flash tools. I think there was some drivers problem, and the process stopped in between, and when i tried to turn the phone on, it only emitted some light and would stay that until the battery would drain. After a few days, it went dead, no response. This was the time I realized that I had to give it to a service center. Unfortunately, the service was awfully bad, and my phone came repaired back after 3 MONTHS! So, I recommend, that you hand it over to a non-micromax service center (as your warranty is now void), and try your luck! All the best!
P.S. My CHD is working awesome now, installed MiUi
[email protected] said:
pls suggest me how i can download the correct drivers.
Click to expand...
Click to collapse
download Mt65xx vcom drivers then see the video below
---------- Post added at 12:54 PM ---------- Previous post was at 12:06 PM ----------
aryankirtan said:
Thank you Shivraj for replying.
But as I said in earlier post, my phone is not going into recovery mode. As I press "Volume +" button, it goes off. I wish somehow I can at least boot my phone into recovery mode!
Have anyone tried USB jig for Micromax phones?
Click to expand...
Click to collapse
just flash the stock backup using SP flash tool
Hi Guys,
My sister's MMX A116 is totally bricked and not even able to turn it on. Earlier It was stuck in bootloop and she gave it to some mobile repairing shop and they hard bricked it . I can't even boot to recovery. Is there any chance of unbricking it? If yes, please tell how.
MrJukeHardbane said:
Hi Guys,
My sister's MMX A116 is totally bricked and not even able to turn it on. Earlier It was stuck in bootloop and she gave it to some mobile repairing shop and they hard bricked it . I can't even boot to recovery. Is there any chance of unbricking it? If yes, please tell how.
Click to expand...
Click to collapse
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
ndbhatt2006 said:
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
Click to expand...
Click to collapse
When I click the download button and connect USB, nothing is happening. It just get stuck to 0%
MrJukeHardbane said:
When I click the download button and connect USB, nothing is happening. It just get stuck to 0%
Click to expand...
Click to collapse
check if your phone connects with the usb port or not?
because this can happen if your phone drivers are not installed or wrong drivers installed
visit micromax website and download drivers for a116 from there first remove old one and install new one then try again.
HIT THANKS IF I HELPED YOU......
ndbhatt2006 said:
check if your phone connects with the usb port or not?
because this can happen if your phone drivers are not installed or wrong drivers installed
visit micromax website and download drivers for a116 from there first remove old one and install new one then try again.
HIT THANKS IF I HELPED YOU......
Click to expand...
Click to collapse
Phone is now detecting but i am not able to flash from SP tools, getting Error : BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069). Haven't found any fix for this error yet.
MrJukeHardbane said:
Phone is now detecting but i am not able to flash from SP tools, getting Error : BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069). Haven't found any fix for this error yet.
Click to expand...
Click to collapse
If your EMMC chip or RAM is damaged by Mobile repairing person then you will be helpless...
but if it is ok then once again try, this time in SP Flash tool select option "Format All + Download" then click on download button
remember never connect phone before the above steps only connect phone after u click on Download button
ndbhatt2006 said:
If your EMMC chip or RAM is damaged by Mobile repairing person then you will be helpless...
but if it is ok then once again try, this time in SP Flash tool select option "Format All + Download" then click on download button
remember never connect phone before the above steps only connect phone after u click on Download button
Click to expand...
Click to collapse
Where is this option Format all + download?
MrJukeHardbane said:
Where is this option Format all + download?[/Qwhi
which version of sp flash tools you use?
if its V5 or higher
then you will find it as per attached image.
Click to expand...
Click to collapse
ndbhatt2006 said:
MrJukeHardbane said:
Where is this option Format all + download?[/Qwhi
which version of sp flash tools you use?
if its V5 or higher
then you will find it as per attached image.
Click to expand...
Click to collapse
Still same error. I guess its as good as a paperweight now.
Click to expand...
Click to collapse
MrJukeHardbane said:
ndbhatt2006 said:
Still same error. I guess its as good as a paperweight now.
Click to expand...
Click to collapse
now there should be hardware problem you can get checked with service center.....
Click to expand...
Click to collapse
ndbhatt2006 said:
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
Click to expand...
Click to collapse
Can we flash custom roms from sp flash tool (the ones which we flash from Cwm recovery)
---------- Post added at 02:12 AM ---------- Previous post was at 02:08 AM ----------
ndbhatt2006 said:
MrJukeHardbane,
First of all you need to download A116 Stock ROM, Drivers and SP Flash Tools by googling.
Then Remove your battery of the phone and SIM cards as well as Memory card,
Then install A116 Drivers in your PC then open SP flash tools window by double clicking on Flash_Tools.exe
the windows of SP Flash tool will open then click on Scatter Loading and search for the A116 Stock ROM you downloaded and extracted and find MT6589_Android_scatter_emmc file and open it
find the Download button on the upper side of window and click on it
Then connect your phone to PC with the data cable and try pressing volume up button and power butter simultaneously 3 to 4 times them you can see at the base of the window your phone will get detected and connected with the port and rest process will be done automatically wail till you see the green circle on the screen.
Once you find green circle remove your device and try to start after fixing Battery and Sim card and memory card.
If your phone is soft bricked... It will definitely boot up and it takes about 10 minutes at first boot up so keep patience..
HIT THANKS IF I HELPED YOU :good:
Click to expand...
Click to collapse
And can u send link for stock Rom and drivers for mmx a116? Please
hey Bro,
I am afraid my A310 phone is bricked now. I had the android L ROM by pintothakur installed on my phone using TWRP touch recovery (Red) before. Today when i tried to install this Xtremevanilla ROM by the Devilashish on my phone (after clearing cache, delvik cache and system) i selected both zip files vanilla and xposed patch and tried to install but it failed. I dont remember the error . Then i tried once again with only Vanilla zip file this time but it failed again. I think then I made a mistake of restarting the phone (without installing another ROM ) It asked me that my phone didn't seem rooted and if i wanted to install SuperSU . I selected installation of Superuser. And after that the phone restarted but could not get past the micromax logo. I tried pressing Vol down button and power button together to go into recovery mode or pressing Vol+ and power for a fast boot, but notihng worked. and now my phone doesn't go beyond that logo. Is there any chance it happened because of some clash in SuperSu Pro already installed on phone and the one it asked me to install after ROM install failure? And when I connect the phone to desktop it says driver could not be installed and shows a battery charging logo with battery almost showing nil but it doesn't show any charging animation just the static low battery charging logo which remained same even after connecting the phone to desktop for more than 2 hours.
So, is there any way I can get my phone back . Any help from anybody would be really appreciated. And I'm sorry if I'm asking this in a wrong forum. Thanks in advance guys.
Smartashu1 said:
hey Bro,
I am afraid my A310 phone is bricked now. I had the android L ROM by pintothakur installed on my phone using TWRP touch recovery (Red) before. Today when i tried to install this Xtremevanilla ROM by the Devilashish on my phone (after clearing cache, delvik cache and system) i selected both zip files vanilla and xposed patch and tried to install but it failed. I dont remember the error . Then i tried once again with only Vanilla zip file this time but it failed again. I think then I made a mistake of restarting the phone (without installing another ROM ) It asked me that my phone didn't seem rooted and if i wanted to install SuperSU . I selected installation of Superuser. And after that the phone restarted but could not get past the micromax logo. I tried pressing Vol down button and power button together to go into recovery mode or pressing Vol+ and power for a fast boot, but notihng worked. and now my phone doesn't go beyond that logo. Is there any chance it happened because of some clash in SuperSu Pro already installed on phone and the one it asked me to install after ROM install failure? And when I connect the phone to desktop it says driver could not be installed and shows a battery charging logo with battery almost showing nil but it doesn't show any charging animation just the static low battery charging logo which remained same even after connecting the phone to desktop for more than 2 hours.
So, is there any way I can get my phone back . Any help from anybody would be really appreciated. And I'm sorry if I'm asking this in a wrong forum. Thanks in advance guys.
Click to expand...
Click to collapse
I tried installing PDAnet on my system but it failed probably because i could not enable USB debugging on phone. (though as i remember it was enabled when my phone last worked)
yes mate a very easy way is there !
Smartashu1 said:
hey Bro,
I am afraid my A310 phone is bricked now. I had the android L ROM by pintothakur installed on my phone using TWRP touch recovery (Red) before. Today when i tried to install this Xtremevanilla ROM by the Devilashish on my phone (after clearing cache, delvik cache and system) i selected both zip files vanilla and xposed patch and tried to install but it failed. I dont remember the error . Then i tried once again with only Vanilla zip file this time but it failed again.
Click to expand...
Click to collapse
see all you need is the stock rom .
and ygdp tool
and should know how to use it too
here is the stock rom with YGDP tool
http://www.needrom.com/download/micromax-a311/
1. Get the upgrade driver files;
2. Power the phone off and connect it to the PC via the data cable of standard configuration; the driver is not installed if it is the first time of upgrade; please install the driver manually, and specify the installation path to the position where the driver is located;
3. After the upgrade driver is successfully installed, the device driver port can be seen in Device Manager:
4. Configuration of Upgrade Platform
Flash tool setup must install first
Click on Next > Next > Next to finish installation
Flash tool shortcut will available on Desktop
Once click on above icon , Below error will appear click close the program
Right click on icon and go to properties
Go to compatibility > Enable below shown “ Run this program in compatibility mode for :”Select system OS , Ex: window 7 > click on Apply > OK
Now double click on Flash tool icon, below screen will appear, Enter Password: 369
REAL FLASHING
1. CLICK ON CONFIG
2.you should have unzipped the STOCK ROM.rar by this time now .
3.select the cpd file you have unzipped
4.now on the side bar a lot of model numbers are there but select only 8297 w!
5.click apply
6.now click start on the main screen
7.now connect the phone while it is completely off and connected via USB
8.the phone would be automatically detected and flash would happen
9.it would go on 1005 complete
Upgrade Successful
if i helped press thanks
yogesh.kalyana said:
see all you need is the stock rom .
and ygdp tool
and should know how to use it too
here is the stock rom with YGDP tool
http://www.needrom.com/download/micromax-a311/
1. Get the upgrade driver files;
2. Power the phone off and connect it to the PC via the data cable of standard configuration; the driver is not installed if it is the first time of upgrade; please install the driver manually, and specify the installation path to the position where the driver is located;
3. After the upgrade driver is successfully installed, the device driver port can be seen in Device Manager:
4. Configuration of Upgrade Platform
Flash tool setup must install first
Click on Next > Next > Next to finish installation
Flash tool shortcut will available on Desktop
Once click on above icon , Below error will appear click close the program
Right click on icon and go to properties
Go to compatibility > Enable below shown “ Run this program in compatibility mode for :”Select system OS , Ex: window 7 > click on Apply > OK
Now double click on Flash tool icon, below screen will appear, Enter Password: 369
REAL FLASHING
1. CLICK ON CONFIG
2.you should have unzipped the STOCK ROM.rar by this time now .
3.select the cpd file you have unzipped
4.now on the side bar a lot of model numbers are there but select only 8297 w!
5.click apply
6.now click start on the main screen
7.now connect the phone while it is completely off and connected via USB
8.the phone would be automatically detected and flash would happen
9.it would go on 1005 complete
Upgrade Successful
if i helped press thanks
Click to expand...
Click to collapse
Thanks buddy, though this YGDP is very new to me.. I'll try it as you suggeseted. Hope this would work. Will inform you.
OK!
Smartashu1 said:
Thanks buddy, though this YGDP is very new to me.. I'll try it as you suggeseted. Hope this would work. Will inform you.
Click to expand...
Click to collapse
tell me if it worked
yogesh.kalyana said:
tell me if it worked
Click to expand...
Click to collapse
Hey, it went well upto last step. Installed drivers and after connecting phone it shows PreLoader USB VCOM(Android) COM3 under ports. Then I configured and started YGDP with CPB file but when I connect the phone, it suddenly disappears from ports list just when the low battery charging logo comes up on phone. And then in YGDP it only continues as Entering download mode..
Dont know what went wrong
I am thinking that I may have installed many drivers from various files I found on net. Though when I tried updating the driver from Ports list today it said I had the up to date driver installed for the device. So, can you please help with possible cause and soultion.. and one funny thing happened (Dont know if it is of any significance) .. once I tried using the CPB file form my pendrive and after starting YGDP it started showing as a FAT32 device and no contents visible. Only when i restarted system it showed the contents as before. Then I copied CPB from USB to a Local drive but still with same problem.. Entering download mode..
Smartashu1 said:
Hey, it went well upto last step. Installed drivers and after connecting phone it shows PreLoader USB VCOM(Android) COM3 under ports. Then I configured and started YGDP with CPB file but when I connect the phone, it suddenly disappears from ports list just when the low battery charging logo comes up on phone. And then in YGDP it only continues as Entering download mode..
Dont know what went wrong
I am thinking that I may have installed many drivers from various files I found on net. Though when I tried updating the driver from Ports list today it said I had the up to date driver installed for the device. So, can you please help with possible cause and soultion.. and one funny thing happened (Dont know if it is of any significance) .. once I tried using the CPB file form my pendrive and after starting YGDP it started showing as a FAT32 device and no contents visible. Only when i restarted system it showed the contents as before. Then I copied CPB from USB to a Local drive but still with same problem.. Entering download mode..
Click to expand...
Click to collapse
Hey, this time I tried on my wndows7 system and it worked till last step where it failed after 98% completion. Here is the dump file it created.
21:19:36 CELL0: Software Version: Assembly - <V3.83Beta_140404_06>
21:19:36 CELL0: Cell 0 USB address is: com18
21:19:36 CELL0: Start Download.
21:19:36 CELL0: Download Started...
21:19:36 CELL0: Downloading CPB:
21:19:36 CELL0: Init Connect Arg.
21:19:36 CELL0: Downlaod DA Start.
21:19:39 CELL0: Downlaod DA Success.
21:19:39 CELL0: This CPB for the Phone don't support Check CID.
21:19:39 CELL0: Verify is Partition be Changed.
21:19:39 CELL0: Partition is not Changed.
21:19:39 CELL0: Get Usb Status Success.
21:19:39 CELL0: Read YL-Parames Partition Start.
21:19:42 CELL0: Read YL-Parames Partition Success.
21:19:42 CELL0: Check between YL-Parames Partition and PhoneInfo Start.
21:19:42 CELL0: Check between YL-Parames Partition and PhoneInfo Failed.
21:19:42 CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.
21:19:43 CELL0: DisConnect.
21:20:03 CELL0: Total download time elapsed: 0 min : 27 sec
21:20:03 CELL0: Downloading CPB: Failed!
No idea why this happened. And phone still disappears from port list few seconds after connecting. I tried by installing SP driver also and I tried by installing win7 VCOM autoinstall driver also (I just found them on different websites on internet)
oh godamnit!
Smartashu1 said:
Hey, this time I tried on my wndows7 system and it worked till last step where it failed after 98% completion. Here is the dump file it created.
21:19:36 CELL0: Software Version: Assembly - <V3.83Beta_140404_06>
21:19:36 CELL0: Cell 0 USB address is: com18
21:19:36 CELL0: Start Download.
21:19:36 CELL0: Download Started...
21:19:36 CELL0: Downloading CPB:
21:19:36 CELL0: Init Connect Arg.
21:19:36 CELL0: Downlaod DA Start.
21:19:39 CELL0: Downlaod DA Success.
21:19:39 CELL0: This CPB for the Phone don't support Check CID.
21:19:39 CELL0: Verify is Partition be Changed.
21:19:39 CELL0: Partition is not Changed.
21:19:39 CELL0: Get Usb Status Success.
21:19:39 CELL0: Read YL-Parames Partition Start.
21:19:42 CELL0: Read YL-Parames Partition Success.
21:19:42 CELL0: Check between YL-Parames Partition and PhoneInfo Start.
21:19:42 CELL0: Check between YL-Parames Partition and PhoneInfo Failed.
21:19:42 CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.
21:19:43 CELL0: DisConnect.
21:20:03 CELL0: Total download time elapsed: 0 min : 27 sec
21:20:03 CELL0: Downloading CPB: Failed!
No idea why this happened. And phone still disappears from port list few seconds after connecting. I tried by installing SP driver also and I tried by installing win7 VCOM autoinstall driver also (I just found them on different websites on internet)
Click to expand...
Click to collapse
nothing to worry about bro
but first i am so sorry i gave you the A311 stock rom instead of a310
i am so truly sorry
let me try to see if i can find a310 cpb file
i will get back to you with that
yogesh.kalyana said:
nothing to worry about bro
but first i am so sorry i gave you the A311 stock rom instead of a310
i am so truly sorry
let me try to see if i can find a310 cpb file
i will get back to you with that
Click to expand...
Click to collapse
Oh, that was by mistake..? i thought you sent that coz a311 and a310 might be having same stock ROM. I tried searching for a310 stock already before posting here but i only found some cpb files on a chinese site. Probably on modaco. Though there were many files 035, 036 n something like that. I dont remember. And trying to download from there was a lil frustrating for me. See if you can make any sense out of that.
http://pan.baidu.com/share/home?uk=2252774741&view=share#category/type=0
woah !
Smartashu1 said:
Oh, that was by mistake..? i thought you sent that coz a311 and a310 might be having same stock ROM. I tried searching for a310 stock already before posting here but i only found some cpb files on a chinese site. Probably on modaco. Though there were many files 035, 036 n something like that. I dont remember. And trying to download from there was a lil frustrating for me. See if you can make any sense out of that.
http://pan.baidu.com/share/home?uk=2252774741&view=share#category/type=0
Click to expand...
Click to collapse
i guess you got kinda lost there buddy !
and don't worry i am always there to help
so here is the ROM CPB file (THE CORRECT ONE THIS TIME)
http://pan.baidu.com/s/1jGzcUYM
this one is shared in chinese so click on the download symbol uptop and select the white box with chinese symbols 837 mb
and yes use 8297W_I01 as your device when configuring it in YGDP
and it is on devhost so no DOWNLOADING ISSUES!
Hope it works
Thanks Bro,
yogesh.kalyana said:
i guess you got kinda lost there buddy !
and don't worry i am always there to help
so here is the ROM CPB file (THE CORRECT ONE THIS TIME)
http://support.moulnisky.com/index.php?dir=Micromax/00_A Serie/A310/Software Versions/V1_04.09.14/
this one is shared in english so i believe you won't find any troubles
and yes use 8297W_I01 as your device when configuring it in YGDP
and it is on devhost so no DOWNLOADING ISSUES!
Hope it works
Click to expand...
Click to collapse
I hope it would work. But I dont have boradband internet connectivity for few days. So I'll inform you once I try it as you said now. Though there is one trouble now. Earlier when I tried with A311 ROM it could reach downloading till 98% but then since that didnt work, I guess i messed up with drivers (installed SP drivers, Vcom drivers, PDA usb drivers, coolpad drivers ) trying to find some solution and now when i tried with that A311 ROM, again it is stuck at Entering download mode.. (and I tried this time with all drivers.. uninstalling and updating all since I dont remember which set of drivers exactly worked last time). So, can you please suggest which drivers to go for with Win7 64 bit or I should continue hit n trial?
n I'm really hating bothering you like this and so much Thanks for your time
it is ok!
Smartashu1 said:
I hope it would work. But I dont have boradband internet connectivity for few days. So I'll inform you once I try it as you said now. Though there is one trouble now. Earlier when I tried with A311 ROM it could reach downloading till 98% but then since that didnt work, I guess i messed up with drivers (installed SP drivers, Vcom drivers, PDA usb drivers, coolpad drivers ) trying to find some solution and now when i tried with that A311 ROM, again it is stuck at Entering download mode.. (and I tried this time with all drivers.. uninstalling and updating all since I dont remember which set of drivers exactly worked last time). So, can you please suggest which drivers to go for with Win7 64 bit or I should continue hit n trial?
n I'm really hating bothering you like this and so much Thanks for your time
Click to expand...
Click to collapse
see a311 can run on a310 roms easily as a310 would obviously is on lower hardware than a311
but a311 has a different architecture that is why it won't flash on you phone
and believe it or not i did not even installed one single software or driver it always worked for me with out it too
just uninstall all the drivers and start flashing with only one specific drivers
if you still need one try these http://www.inforaid.com/micromax-canvas-nitro-a311-pc-suite/ and until you keep pressing thanks i woll continue helping you or anybody else just joking but still hit thanks
please help me
yogesh.kalyana said:
i guess you got kinda lost there buddy !
and don't worry i am always there to help
so here is the ROM CPB file (THE CORRECT ONE THIS TIME)
http://pan.baidu.com/s/1jGzcUYM
this one is shared in chinese so click on the download symbol uptop and select the white box with chinese symbols 837 mb
and yes use 8297W_I01 as your device when configuring it in YGDP
and it is on devhost so no DOWNLOADING ISSUES!
Hope it works
Click to expand...
Click to collapse
please help me in a311. i am facing sensors issue and volume up button issue.
Refresh ROM and see if problem exists still
Sent from my Moto G using XDA Free mobile app
yes i tried but even on stock i am facing proximity issue.
Silver Droid said:
Refresh ROM and see if problem exists still
Sent from my Moto G using XDA Free mobile app
Click to expand...
Click to collapse
Even i am on stock rom i am still having proximity sensor issue. Now i have flashed hive ui rom on a311. Here proximity is fixed but volume up event is not correct. Works as volume down button
rohitjaiswal said:
Even i am on stock rom i am still having proximity sensor issue. Now i have flashed hive ui rom on a311. Here proximity is fixed but volume up event is not correct. Works as volume down button
Click to expand...
Click to collapse
Format the system and flash ROM may be that could solve
buddy !
rohitjaiswal said:
please help me in a311. i am facing sensors issue and volume up button issue.
Click to expand...
Click to collapse
for a311 go to needrom link which i provied first !
yogesh.kalyana said:
for a311 go to needrom link which i provied first !
Click to expand...
Click to collapse
After flashing A311 Stock on A311 device is not solving proximity sensor bug only. rest of it everything is working.
I have tired with some sites given u and others.
http://www.needrom.com/wp-content/up...romax-A311.rar ==== Needrom Link
http://www.mediafire.com/download/of...7W_I02.rar==== Mediafire Link.
I believe these two links for Stock A311 so i have flashed these . It shows me Custom id as MICROMAX A311.
I am so confused here and struck.
try this !
rohitjaiswal said:
After flashing A311 Stock on A311 device is not solving proximity sensor bug only. rest of it everything is working.
I have tired with some sites given u and others.
http://www.needrom.com/wp-content/up...romax-A311.rar ==== Needrom Link
http://www.mediafire.com/download/of...7W_I02.rar==== Mediafire Link.
I believe these two links for Stock A311 so i have flashed these . It shows me Custom id as MICROMAX A311.
I am so confused here and struck.
Click to expand...
Click to collapse
http://www.needrom.com/download/micromax-a311/
the links by you were wrong and corrupted try this first
and if proximity bug still there try this patch via TWRP or CWM
https://drive.google.com/file/d/0B2C-6Yy6LhcMX2NLTUloUERGOFU/view?usp=sharing
if it still ain't working your sensor might be gone for good !
Finallly.. It's working now
yogesh.kalyana said:
see a311 can run on a310 roms easily as a310 would obviously is on lower hardware than a311
but a311 has a different architecture that is why it won't flash on you phone
and believe it or not i did not even installed one single software or driver it always worked for me with out it too
just uninstall all the drivers and start flashing with only one specific drivers
if you still need one try these http://www.inforaid.com/micromax-canvas-nitro-a311-pc-suite/ and until you keep pressing thanks i woll continue helping you or anybody else just joking but still hit thanks
Click to expand...
Click to collapse
Hey..
I downloaded this new CPB file and evrything as before.. but as happened last time.. It didn't move beyond Entering download mode..
Then I tried a solution I found in modaco.
I turned phone off, kept Vol buttons pressed and connected to USB and to my surprise phone booted into recovery (TWRP in my case) :laugh::victory: I hadn't expected that
Then as usual i proceeded with wiping n installation from SD card.
Still Thank you so much for your help. Just mentioned these steps as it may help someone in similar condition where phone fails to boot normally.
plz help for flashing stock rom using ygdp tools it detects cpb file and also detects mobile in cell0 but cell 0 download file fails plzzzzzzzzzzzzzzzz helppppppppp frnds................
it shows th download screen dump saved message
saurabhtekade said:
plz help for flashing stock rom using ygdp tools it detects cpb file and also detects mobile in cell0 but cell 0 download file fails plzzzzzzzzzzzzzzzz helppppppppp frnds................
it shows th download screen dump saved message
Click to expand...
Click to collapse
1 Download the stock rom that is in .CPB format.
2 open YGDP tool
3 go to config> select ur device that is may be 8927W > select the rom that is in CPB format.
4 click Ok/Verify... after verification of file.
5 remove battery, sim, memory card and connect it to ur computer/laptop.
6 press volume up or down button untill u hear a sound of connection to the computer. And click start in YGDP tool. Wait untill cell0 show 100%.
7 remove the usb cable and enjoy.......
Remember first reboot takes too much time it may be about 5-10 minutes.
Note:- connect the phone just before clicking the start button.
@saurabhtekade here is twrp flashable stock rom zip for a311
http://forum.xda-developers.com/a310/orig-development/rom-twrp-flashable-micromax-canvas-t3287008
Now, i have seen countless cases of people being not able to flash their MMX A311, as for me I was having the same problem too, turns out that the driver is the main problem.
I was trying out YGDP but i was stuck at "Enabling Download Mode"
and while trying out SP tools i was getting an error "s_brom_cmd_jump_da_fail (0x7f3) " .
Then again, I tried many things, and got my phone working in 10 minutes. :good:
So if u too are stuck, then try my method.
It is highly recommended you do this in Windows 7.
I did everything while my phone was switched off but battery was inserted.
Disconnect your PC from internet just to be double careful about the flashing.
First getting the proper driver:
Now, before installing the driver, make sure that you dont have any other driver installed rather than the one which i will provide, if you think you might have installed some other driver then try removing it by "usdreview" (but it didn't work for me though that's why PLEASE TRY THIS ON ANOTHER COMPUTER OR LAPTOP, MAYBE IF YOU HAVE ANOTHER LAPTOP OR COMPUTER OR MAYBE TRY IT ON YOUR FRIEND'S SYSTEM. THIS SOLVED THE "ENABLING DOWNLOAD MODE" PROBLEM FOR ME)
Download this driver, I did with this one:
Remove the (dot) and put " . " in the link. .
www(dot)mediafire(dot)com/file/8v32j8h5doflzi0/Mediatek+MT65xx+Preloader+Driver(dot)rar
Click to expand...
Click to collapse
Extract it and remember where the folder has been extracted to, as it will be needed to install the driver.
Installing the driver:
Open up Device Manager.
right click on My Computer > Manage > on the side pane click on "Device Manager"
Keep it open.
Now first CHOOSE A SINGLE USB PORT WHICH WILL BE USED BY YOU THROUGHOUT THIS WHOLE PROCESS. DON'T CHANGE IT!
Now use your usb data cable and insert it into your chosen USB port and then to your phone.
As you will insert it you will see a device popup in 'Other Devices' or some other tab named as "MTK65xx Preloader" or something similar like that.
NOW BE QUICK IT DISAPPEARS IN 3-4 SECONDS !!
Quickly right click on mtk65xx preloader and select "Update Driver Software"
Now as in the new window opened up, select " Browse my own computer to install the driver"
Browse to the DOWNLOADED DRIVER'S folder, select the folder "Win7" for Windows 7 and Above.
Now the driver will be installed.
Now after being installed, take out your phone from the usb cable, dont remove the usb cable from the computer because you make mistake while again inserting it back into to a different port.
Getting the stock rom and YGDP tool:
Now get the stock rom for A311 and YGDP tool from any verified site.
I downloaded mine from :
Remove the (dot) and put " . " in the link.
www(dot)needrom(dot)com/download/micromax-a311
Click to expand...
Click to collapse
Download from this site needs user to be logged in, it barely took 2 mins for me to register and download it.
If you have any other site you trust then go on and download it from there, but I recommmend you to follow my steps and sites as I did everything and succeeded.
Download the ROM and also the YGDP tool.
Extract the downloaded file to some specific folder as this is the ROM and the tool required.
Installing and Using the YGDP tool:
I have seen people recommending latest YGDP tool but on the contrary I recommend the downloaded old version from the previous step, it worked for me like a charm!!
Install the YGDP tool from the extracted folder.
After installation, YGDP desktop icon will appear, open it.
put the password as: 369
Now, on the top pane, press the button "Config"
In the window opened, on the side pane, carefully select "8297W" for A311
And after selecting that, on the left side section,
in the " Please select CPB file : " , click on the button beside it and browse for your extracted folder of ROM and select it !
now it click " Apply " button .
It will take 1-2 minutes, and after this you will be brought back to the main window!
Now click on " Start "
And wait till in the bottom message log it says " ENABLING DOWNLOAD MODE" , now follow the next step !!
Flashing your phone:
As YGDP stays in enabling download mode, now insert your phone back to the usb cable which was left out in the computer.
Now, if you did everything correctly, YOUR PHONE WILL BE DETECTED and YGDP will start flashing by itself, wait till it says 100% with a green bar.
Remove your phone from the USB cable and then click "STOP" in the main window of the YGDP tool.
Power on your phone.
Your phone will be successfully be flashed and alive !!! :fingers-crossed:
FROM NOW ON, ALWAYS MAKE A BACKUP . :silly:
Feel free to ask questions. :laugh:
If u have suggestions, I'm open for it!! :laugh:
While I am connecting to the computer it does not recognise it and continuously connecting and disconnecting the USB drive and I have tried different ways like why GDP tool and SP Flash tool when I tried with why GDP tool it struck at the entering download mode and when I tried with SP Flash tool it recognise the device but ends with an error message finally the problem is my computer is not detecting the device properly and I have install the drivers manually also but of no use now I am not able to go for go to the recovery mode my phones is continuously rebooting please help me thanks in advance
as you said i have done all the things, and its turned out as green bar. everything is ok, but while power on my device it will only shows the micromax logo it wont go further... kindly suggest me about what to do next...
anyone active here?