Related
Hey, I was playing around with my "Hack dock" on a Fascinate which was given to me at the Big Android BBQ from the gentleman who runs RootzWiki. The unique thing about this device is that it was totally functional when I received it. It was given to me with a busted screen. I'm going to turn this into a fully functional development platform as I have done with the Captivate.
I've squared away UnBrickable Mod on the device and I will be posting the information soon. I wanted to post up some UART Output from the device as I go along. through it. This is valuable for debugging information and can open some doors for development.
While I was playing around with the UART output I came across a SBL> prompt command which I had never seen before. The command is "movi_patch". If anyone can shed some light on it, I'd appreciate it.
Code:
SBL> movi_patch
###################################
MOVINAND PATCH START
###################################
Movi Init .....Enable Movinand
[hsmmc_init] MMC card is detected
Product Name : M2G1DE
<display_card_info:939>normal csd
read_bl_len: 10
read_bl_partial: 0
One Block Size: 1024 Byte
c_size: 3815
c_size_multi: 7
Total Card Size: 1909 MByte
MoviNand Initialization Complete!
Success!
Pre Patch ....Enter Patch Mode!
Success!
Success!
Good Block Erase!
Success!
Success!
Success!
Pre-Patch Binary Read ...
Success!
Pre-Patch Binary Write ...
.
Pre-Patch Confirm!
Success!
Success!
Power Off!
Movi Init (Format) .....Enable Movinand
[hsmmc_init] MMC card is detected
Product Name : 000000
<display_card_info:939>normal csd
read_bl_len: 10
read_bl_partial: 0
One Block Size: 1024 Byte
c_size: 3815
c_size_multi: 7
Total Card Size: 1909 MByte
MoviNand Initialization Complete!
Success!
Power Off!
Power On!
###################################
MOVINAND PATCH FINSH
###################################
Success!
SBL> reset
Rebooting...
I"ve never seen anything like it...
Here's some more of the UART output/boot sequence.. For those who don't know, this is like the bios on a PC.
Code:
�
-----------------------------------------------------------
Samsung Primitive Bootloader (PBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
-----------------------------------------------------------
+n1stVPN 2688
+nPgsPerBlk 64
PBL found bootable SBL: Partition(3).
Set cpu clk. from 400MHz to 800MHz.
IROM e-fused version.
-----------------------------------------------------------
Samsung Secondary Bootloader (SBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
Board Name: ARIES REV 02
Build On: Feb 28 2011 18:02:24
-----------------------------------------------------------
Re_partition: magic code(0x0)
[PAM: ] ++FSR_PAM_Init
[PAM: ] OneNAND physical base address : 0xb0000000
[PAM: ] OneNAND virtual base address : 0xb0000000
[PAM: ] OneNAND nMID=0xec : nDID=0x50
[PAM: ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 12
partitions loading success
board partition information update.. source: 0x0
.Done.
read 1 units.
==== PARTITION INFORMATION ====
ID : IBL+PBL (0x0)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : PIT (0x1)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 1
NO_UNITS : 1
===============================
ID : EFS (0x14)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 2
NO_UNITS : 40
===============================
ID : SBL (0x3)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 42
NO_UNITS : 5
===============================
ID : SBL2 (0x4)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 47
NO_UNITS : 5
===============================
ID : PARAM (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 52
NO_UNITS : 20
===============================
ID : KERNEL (0x6)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 72
NO_UNITS : 30
===============================
ID : RECOVERY (0x7)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 102
NO_UNITS : 30
===============================
ID : FACTORYFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 132
NO_UNITS : 1286
===============================
ID : DBDATAFS (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1418
NO_UNITS : 444
===============================
ID : CACHE (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1862
NO_UNITS : 140
===============================
ID : MODEM (0xb)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 2002
NO_UNITS : 2
===============================
loke_init: j4fs_open success..
load_lfs_parameters valid magic code and version.
load_debug_level reading debug level from file successfully(0x44494d44).
quick_start- quick start is executed!
init_fuel_gauge: vcell = 4110mV, soc = 90
reading nps status file is successfully!.
nps status=0x504d4f43
PMIC_IRQ1 = 0x28
PMIC_IRQ2 = 0x0
PMIC_IRQ3 = 0x0
PMIC_IRQ4 = 0x0
PMIC_STATUS1 = 0x40
PMIC_STATUS2 = 0x2c
get_debug_level current debug level is 0x44494d44.
get_debug_level current debug level is 0x44494d44.
aries_process_platform: Debug Level Mid
keypad_scan: key value ----------------->= 0x0
CONFIG_ARIES_REV:32 , CONFIG_ARIES_REV03:48
DISPLAY_PATH_SEL[MDNIE 0x1]is on
MDNIE setting Init start!!
vsync interrupt is off
video interrupt is off
[fb0] turn on
MDNIE setting Init end!!
set_boot_mode: boot mode = 1
aries_process_platform: final s1 booting mode = 1
Autoboot (0 seconds) in progress, press any key to stop Autoboot aborted..
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL>
SBL> help
Following commands are supported:
* setenv
* saveenv
* printenv
* help
* reset
* boot
* kernel
* format
* open
* close
* erasepart
* eraseall
* loadkernel
* showpart
* addpart
* delpart
* savepart
* nkernel
* nramdisk
* nandread
* nandwrite
* usb
* mmctest
* keyread
* movi_patch
* usb_read
* usb_write
* fuelgauge
* pmic_read
* pmic_write
To get commands help, Type "help <command>"
SBL> printenv
PARAM Rev 1.3
SERIAL_SPEED : 7
LOAD_RAMDISK : 0
BOOT_DELAY : 0
LCD_LEVEL : 97
SWITCH_SEL : 5
PHONE_DEBUG_ON : 0
LCD_DIM_LEVEL : 0
LCD_DIM_TIME : 6
MELODY_MODE : 1
REBOOT_MODE : 0
NATION_SEL : 0
LANGUAGE_SEL : 0
SET_DEFAULT_PARAM : 0
PARAM_INT_13 : 0
TOOL_LAUNCHER_STATE : 1
VERSION : I9000XXIL
CMDLINE : console=ttySAC2,115200 loglevel=3 wipedata
DELTA_LOCATION : /mnt/rsv
PARAM_STR_3 :
PARAM_STR_4 :
SBL> showpart
board partition information update.. source: 0x0
.Done.
read 1 units.
==== PARTITION INFORMATION ====
ID : IBL+PBL (0x0)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : PIT (0x1)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 1
NO_UNITS : 1
===============================
ID : EFS (0x14)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 2
NO_UNITS : 40
===============================
ID : SBL (0x3)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 42
NO_UNITS : 5
===============================
ID : SBL2 (0x4)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 47
NO_UNITS : 5
===============================
ID : PARAM (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 52
NO_UNITS : 20
===============================
ID : KERNEL (0x6)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 72
NO_UNITS : 30
===============================
ID : RECOVERY (0x7)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 102
NO_UNITS : 30
===============================
ID : FACTORYFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 132
NO_UNITS : 1286
===============================
ID : DBDATAFS (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1418
NO_UNITS : 444
===============================
ID : CACHE (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1862
NO_UNITS : 140
===============================
ID : MODEM (0xb)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 2002
NO_UNITS : 2
===============================
SBL> setenv SWITCH_SEL 6543
argv[0] : setenv
argv[1] : SWITCH_SEL
argv[2] : 6543
value : 6543
SBL> setenv PHONE_DEBUG_ON 1
argv[0] : setenv
argv[1] : PHONE_DEBUG_ON
argv[2] : 1
value : 1
SBL> saveenv
save param.blk, size: 5268
save param.blk successfully.
SBL> reset
Rebooting...
SB
This shows default values for anyone who wants to modify them.
And here's the boot after enabling some debug output
Code:
-----------------------------------------------------------
Samsung Primitive Bootloader (PBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
-----------------------------------------------------------
+n1stVPN 2688
+nPgsPerBlk 64
PBL found bootable SBL: Partition(3).
Set cpu clk. from 400MHz to 800MHz.
IROM e-fused version.
-----------------------------------------------------------
Samsung Secondary Bootloader (SBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
Board Name: ARIES REV 02
Build On: Feb 28 2011 18:02:24
-----------------------------------------------------------
Re_partition: magic code(0x0)
[PAM: ] ++FSR_PAM_Init
[PAM: ] OneNAND physical base address : 0xb0000000
[PAM: ] OneNAND virtual base address : 0xb0000000
[PAM: ] OneNAND nMID=0xec : nDID=0x50
[PAM: ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 12
partitions loading success
board partition information update.. source: 0x0
.Done.
read 1 units.
==== PARTITION INFORMATION ====
ID : IBL+PBL (0x0)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : PIT (0x1)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 1
NO_UNITS : 1
===============================
ID : EFS (0x14)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 2
NO_UNITS : 40
===============================
ID : SBL (0x3)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 42
NO_UNITS : 5
===============================
ID : SBL2 (0x4)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 47
NO_UNITS : 5
===============================
ID : PARAM (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 52
NO_UNITS : 20
===============================
ID : KERNEL (0x6)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 72
NO_UNITS : 30
===============================
ID : RECOVERY (0x7)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 102
NO_UNITS : 30
===============================
ID : FACTORYFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 132
NO_UNITS : 1286
===============================
ID : DBDATAFS (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1418
NO_UNITS : 444
===============================
ID : CACHE (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1862
NO_UNITS : 140
===============================
ID : MODEM (0xb)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 2002
NO_UNITS : 2
===============================
loke_init: j4fs_open success..
load_lfs_parameters valid magic code and version.
load_debug_level reading debug level from file successfully(0x44494d44).
init_fuel_gauge: vcell = 4113mV, soc = 90
reading nps status file is successfully!.
nps status=0x504d4f43
PMIC_IRQ1 = 0x0
PMIC_IRQ2 = 0x0
PMIC_IRQ3 = 0x0
PMIC_IRQ4 = 0x0
PMIC_STATUS1 = 0x40
PMIC_STATUS2 = 0x2c
get_debug_level current debug level is 0x44494d44.
get_debug_level current debug level is 0x44494d44.
aries_process_platform: Debug Level Mid
keypad_scan: key value ----------------->= 0x0
CONFIG_ARIES_REV:32 , CONFIG_ARIES_REV03:48
DISPLAY_PATH_SEL[MDNIE 0x1]is on
MDNIE setting Init start!!
vsync interrupt is off
video interrupt is off
[fb0] turn on
MDNIE setting Init end!!
set_boot_mode: boot mode = 1
aries_process_platform: final s1 booting mode = 1
Autoboot (0 seconds) in progress, press any key to stop
get_debug_level current debug level is 0x44494d44.
get_debug_level current debug level is 0x44494d44.
boot_kernel: Debug Level 0x44494d44
Load Partion idx = (6)
Loading Partion idx = (6)
..............................done
Kernel read success from kernel partition no.6, idx.6.
setting param.serialnr=0x32321357 0x21bb00ec
setting param.board_rev=0x20
setting param.cmdline=console=ttySAC2,115200 loglevel=3 wipedata
Starting kernel at 0x32000000...
Uncompressing Linux... done, booting the kernel.
<hit enter to activate fiq debugger>
I should mention that this device came with CM7 on it. I will put together a Heimdall One-Click and flash back to stock, then update this post.
Here is the kernel loading into power-off battery charging mode
Code:
-----------------------------------------------------------
Samsung Primitive Bootloader (PBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
-----------------------------------------------------------
+n1stVPN 2688
+nPgsPerBlk 64
+n1stVPN 3008
+nPgsPerBlk 64
PBL found bootable SBL: Partition(4).
Set cpu clk. from 400MHz to 800MHz.
IROM e-fused version.
-----------------------------------------------------------
Samsung Secondary Bootloader (SBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
Board Name: ARIES REV 02
Build On: Oct 26 2010 14:22:42
-----------------------------------------------------------
Re_partition: magic code(0x0)
[PAM: ] ++FSR_PAM_Init
[PAM: ] OneNAND physical base address : 0xb0000000
[PAM: ] OneNAND virtual base address : 0xb0000000
[PAM: ] OneNAND nMID=0xec : nDID=0x50
[PAM: ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 12
partitions loading success
board partition information update.. source: 0x0
.Done.
read 1 units.
==== PARTITION INFORMATION ====
ID : IBL+PBL (0x0)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : PIT (0x1)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 1
NO_UNITS : 1
===============================
ID : EFS (0x14)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 2
NO_UNITS : 40
===============================
ID : SBL (0x3)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 42
NO_UNITS : 5
===============================
ID : SBL2 (0x4)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 47
NO_UNITS : 5
===============================
ID : PARAM (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 52
NO_UNITS : 20
===============================
ID : KERNEL (0x6)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 72
NO_UNITS : 30
===============================
ID : RECOVERY (0x7)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 102
NO_UNITS : 30
===============================
ID : FACTORYFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 132
NO_UNITS : 1286
===============================
ID : DBDATAFS (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1418
NO_UNITS : 444
===============================
ID : CACHE (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1862
NO_UNITS : 140
===============================
ID : MODEM (0xb)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 2002
NO_UNITS : 2
===============================
loke_init: j4fs_open success..
load_lfs_parameters valid magic code and version.
load_debug_level reading debug level from file successfully(0x574f4c44).
quick_start- quick start is executed!
init_fuel_gauge: vcell = 3790mV, soc = 36
reading nps status file is successfully!.
nps status=0x504d4f43
PMIC_IRQ1 = 0x0
PMIC_IRQ2 = 0x0
PMIC_IRQ3 = 0x0
PMIC_IRQ4 = 0x0
PMIC_STATUS1 = 0x40
PMIC_STATUS2 = 0x2c
get_debug_level current debug level is 0x574f4c44.
aries_process_platform: Debug Level Low
keypad_scan: key value ----------------->= 0x0
CONFIG_ARIES_REV:32 , CONFIG_ARIES_REV03:48
DISPLAY_PATH_SEL[MDNIE 0x1]is on
MDNIE setting Init start!!
vsync interrupt is off
video interrupt is off
[fb0] turn on
MDNIE setting Init end!!
set_boot_mode: boot mode = 1
aries_process_platform: final s1 booting mode = 1
Autoboot (0 seconds) in progress, press any key to stop
get_debug_level current debug level is 0x574f4c44.
get_debug_level current debug level is 0x574f4c44.
boot_kernel: Debug Level Low
Load Partion idx = (6)
Loading Partion idx = (6)
..............................done
Kernel read success from kernel partition no.6, idx.6.
setting param.serialnr=0x32321357 0x21bb00ec
setting param.board_rev=0x20
setting param.cmdline=console=ttySAC2,115200 loglevel=9
Starting kernel at 0x32000000...
Uncompressing Linux...................................................................................................................................................................................
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32.9 ([email protected]) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 Fri Jul 8 18:12:14 KST 2011
[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: SMDKC110
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 20480
[ 0.000000] free_area_init_node: node 0, pgdat c1069aa8, node_mem_map c1240000
[ 0.000000] Normal zone: 160 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 20320 pages, LIFO batch:3
[ 0.000000] On node 1 totalpages: 65536
[ 0.000000] free_area_init_node: node 1, pgdat c106a160, node_mem_map d0002000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] On node 2 totalpages: 32768
[ 0.000000] free_area_init_node: node 2, pgdat c106a818, node_mem_map e0001000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32512 pages, LIFO batch:7
[ 0.000000] On node 3 totalpages: 0
[ 0.000000] free_area_init_node: node 3, pgdat c106aed0, node_mem_map c12e8c20
[ 0.000000] Normal zone: 1 pages exceeds realsize 0
[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110222)
[ 0.000000] s5pv210_init_clocks: initializing clocks
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] copy: bad source 0
[ 0.000000] mout_audss: bad source 0
[ 0.000000] s5pv210_setup_clocks: registering clocks
[ 0.000000] s5pv210_setup_clocks: clkdiv0 = 14131330, clkdiv1 = 00300400
[ 0.000000] s5pv210_setup_clocks: xtal is 24000000
[ 0.000000] S5PV210: PLL settings, A=800000000, M=667000000, E=96000000
[ 0.000000] s5pv210: 33554432 bytes system memory reserved for mfc at 0x312f3000
[ 0.000000] s5pv210: 33554432 bytes system memory reserved for mfc at 0x40204000
[ 0.000000] s5pv210: 12582912 bytes system memory reserved for fimc0 at 0x42204000
[ 0.000000] s5pv210: 1048576 bytes system memory reserved for fimc1 at 0x42e04000
[ 0.000000] s5pv210: 12582912 bytes system memory reserved for fimc2 at 0x42f04000
[ 0.000000] s5pv210: 2097152 bytes system memory reserved for pmem at 0x332f3000
[ 0.000000] s5pv210: 4194304 bytes system memory reserved for pmem_gpu1 at 0x334f3000
[ 0.000000] s5pv210: 1536000 bytes system memory reserved for pmem_adsp at 0x338f3000
[ 0.000000] s5pv210: 10485760 bytes system memory reserved for texstream at 0x33a6a000
[ 0.000000]
[ 0.000000] Skipping memset of fb base address 0x4fc00000 -------
[ 0.000000] s5pv210: 3145728 bytes system memory reserved for fimd at 0x4fc00000
[ 0.000000] s5pv210: 262144 bytes system memory reserved for wifi at 0x3446a000
[ 0.000000] Built 3 zonelists in Zone order, mobility grouping on. Total pages: 117856
[ 0.000000] Kernel command line: console=ttySAC2,115200 loglevel=9
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 80MB 256MB 128MB = 464MB total
[ 0.000000] Memory: 339468KB available (9240K code, 1899K data, 7152K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=4
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:339
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2147483647]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC2] enabled
[ 0.366831] Calibrating delay loop... 796.20 BogoMIPS (lpj=1556480)
[ 0.450413] Mount-cache hash table entries: 512
[ 0.455270] Initializing cgroup subsys debug
[ 0.459117] Initializing cgroup subsys cpuacct
[ 0.463534] Initializing cgroup subsys freezer
[ 0.467980] CPU: Testing write buffer coherency: ok
[ 0.477113] KERNEL:kernel_sec_get_debug_level_from_boot=0x574f4c44
[ 0.481866] KERNEL:magic_number=0x0 DEBUG LEVEL low!!
[ 0.486861] (kernel_sec_set_upload_cause) : upload_cause set 0
[ 0.497612] regulator: core version 0.5
[ 0.500373] NET: Registered protocol family 16
[ 0.520404] S5PC110 Hardware version : EVT1
[ 0.524028] HWREV is 0x7
[ 0.526115] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.544089] aries_init_wifi_mem
[ 0.545787] aries_init_wifi_mem success
[ 0.549624] recovery_dev_register
[ 0.552874] create_recovery_class
[ 0.556535] S5PV210 Power Domain API Enable
[ 0.561293] S5PV210: Initializing architecture
[ 0.564803] S3C PL330-DMA Controller Driver, (c) 2008-2009 Samsung Electronics
[ 0.571957] Total 24 DMA channels will be initialized.
[ 0.578423] DMA: got clock for controller 0 and disabled
[ 0.583149] DMA: got clock for controller 1 and disabled
[ 0.588553] DMA: got clock for controller 2 and disabled
[ 0.594646] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[ 0.601679] s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
[ 0.610068] s3c24xx-pwm s3c24xx-pwm.2: tin at 4168750, tdiv at 4168750, tin=divclk, base 12
[ 0.618392] s3c24xx-pwm s3c24xx-pwm.3: tin at 4168750, tdiv at 4168750, tin=divclk, base 16
[ 0.646354] bio: create slab <bio-0> at 0
[ 0.650199] vgaarb: loaded
[ 0.652482] SCSI subsystem initialized
[ 0.656524] i2c-gpio i2c-gpio.4: using pins 247 (SDA) and 246 (SCL)
[ 0.662084] i2c-gpio i2c-gpio.5: using pins 203 (SDA) and 204 (SCL)
[ 0.668801] regulator: DCDC1: 750 <--> 1500 mV
[ 0.672841] regulator: DCDC2: 750 <--> 1500 mV
[ 0.677558] regulator: LDO4: 3300 mV
[ 0.680953] regulator: LDO7: 1600 <--> 3600 mV
[ 0.685469] regulator: LDO17: 1600 <--> 3600 mV
[ 0.690144] i2c-gpio i2c-gpio.6: using pins 206 (SDA) and 209 (SCL)
[ 0.696313] i2c-gpio i2c-gpio.7: using pins 201 (SDA) and 202 (SCL)
[ 0.702765] i2c-gpio i2c-gpio.8: using pins 42 (SDA) and 43 (SCL)
[ 0.708621] i2c-gpio i2c-gpio.9: using pins 245 (SDA) and 244 (SCL)
[ 0.714920] i2c-gpio i2c-gpio.10: using pins 197 (SDA) and 198 (SCL)
[ 0.721214] i2c-gpio i2c-gpio.11: using pins 114 (SDA) and 98 (SCL)
[ 0.727246] i2c-gpio i2c-gpio.12: using pins 173 (SDA) and 172 (SCL)
[ 0.735219] s3c-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
[ 0.740439] s3c-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
[ 0.746138] s3c-i2c s3c2410-i2c.2: i2c-2: S3C I2C adapter
[ 0.751898] Bluetooth: Core ver 2.15
[ 0.754256] NET: Registered protocol family 31
[ 0.758498] Bluetooth: HCI device and connection manager initialized
[ 0.764763] Bluetooth: HCI socket layer initialized
[ 0.770013] Switching to clocksource clock_source_systimer
[ 0.784918] NET: Registered protocol family 2
[ 0.788265] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.796083] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.802289] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.809057] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.815055] TCP reno registered
[ 0.818394] NET: Registered protocol family 1
[ 0.854712] [BT] rfkill_register(bt_rfk)
[ 0.857638] [BT] Device Powering ON
[ 0.860813] [BT] GPIO_BT_nRST = 0
[ 0.864122] [BT] bt_host_wake_irq_handler start
[ 0.868675] [BT] GPIO_WLAN_BT_EN = 1
[ 0.974443] [BT] GPIO_BT_nRST = 1
[ 0.976444] [BT] Device Powering OFF
[ 0.979949] [BT] bt_host_wake_irq_handler start
[ 0.984454] [BT] GPIO_BT_nRST = 0
[ 0.987745] [BT] GPIO_WLAN_BT_EN = 0
[ 0.991619] [BT] bt_host_wake_irq_handler start
[ 0.996167] [BT] In the unblocked state of the sleep
[ 1.000782] [BT] GPIO_BT_WAKE = 0
[ 1.004051] [BT] wake_unlock(bt_wake_lock)
[ 1.008192] [BT] In the unblocked state of the sleep
[ 1.013085] [BT] GPIO_BT_WAKE = 0
[ 1.016366] [BT] wake_unlock(bt_wake_lock)
[ 1.020440] [BT] bt_host_wake_irq_handler start
[ 1.025275] S5PC11X_FREQ_TAB=0 , S5PC11X_MAXFREQLEVEL=4
[ 1.030508] S5PV210 ADC driver, (c) 2010 Samsung Electronics
[ 1.037481] [ JACK_DRIVER (sec_jack_init,791) ]
[ 1.040677] SEC HEADSET: Registering headset driver
[ 1.045917] input: sec_jack as /devices/virtual/input/input0
[ 1.051168] [ JACK_DRIVER (sec_jack_probe,631) ] registering switch_sendend switch_dev sysfs sec_jack
[ 1.060720] SISO:registering switch_sendend switch_dev
[ 1.066059] ##########[send_end_irq_handler irq : headset_state : 0 ]##########
[ 1.072924] [ JACK_DRIVER (sec_jack_probe,671) ] sended isr send=0Xbe, ret =0
[ 1.079947] ##########[detect_irq_handler]##########
[ 1.084982] [ JACK_DRIVER (sec_jack_probe,688) ] detect isr send=0X26, ret =0
[ 1.092080] ------------[ cut here ]------------
[ 1.096664] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x64/0x130()
[ 1.104455] autorequest GPIO-208
[ 1.107664] Modules linked in:
[ 1.110733] [<c070cb70>] (unwind_backtrace+0x0/0xf4) from [<c0b81de8>] (dump_stack+0x20/0x24)
[ 1.119217] [<c0b81de8>] (dump_stack+0x20/0x24) from [<c074451c>] (warn_slowpath_common+0x60/0x70)
[ 1.128145] [<c074451c>] (warn_slowpath_common+0x60/0x70) from [<c0744588>] (warn_slowpath_fmt+0x38/0x40)
[ 1.137684] [<c0744588>] (warn_slowpath_fmt+0x38/0x40) from [<c08c6f70>] (gpio_ensure_requested+0x64/0x130)
[ 1.147398] [<c08c6f70>] (gpio_ensure_requested+0x64/0x130) from [<c08c70e4>] (gpio_direction_output+0xa8/0x118)
[ 1.157550] [<c08c70e4>] (gpio_direction_output+0xa8/0x118) from [<c0718e9c>] (sec_jack_probe+0x314/0x4f0)
[ 1.167179] [<c0718e9c>] (sec_jack_probe+0x314/0x4f0) from [<c091f8c4>] (platform_drv_probe+0x28/0x2c)
[ 1.176454] [<c091f8c4>] (platform_drv_probe+0x28/0x2c) from [<c091e3e8>] (driver_probe_device+0x8c/0x17c)
[ 1.186080] [<c091e3e8>] (driver_probe_device+0x8c/0x17c) from [<c091e574>] (__driver_attach+0x9c/0xa0)
[ 1.195447] [<c091e574>] (__driver_attach+0x9c/0xa0) from [<c091da80>] (bus_for_each_dev+0x70/0x9c)
[ 1.204467] [<c091da80>] (bus_for_each_dev+0x70/0x9c) from [<c091e25c>] (driver_attach+0x2c/0x30)
[ 1.213313] [<c091e25c>] (driver_attach+0x2c/0x30) from [<c091d180>] (bus_add_driver+0xd8/0x328)
[ 1.222073] [<c091d180>] (bus_add_driver+0xd8/0x328) from [<c091e880>] (driver_register+0x88/0x19c)
[ 1.231095] [<c091e880>] (driver_register+0x88/0x19c) from [<c091fe60>] (platform_driver_register+0x60/0x68)
[ 1.240899] [<c091fe60>] (platform_driver_register+0x60/0x68) from [<c000f978>] (sec_jack_init+0x2c/0x34)
[ 1.250442] [<c000f978>] (sec_jack_init+0x2c/0x34) from [<c07043f4>] (do_one_initcall+0x44/0x1d0)
[ 1.259282] [<c07043f4>] (do_one_initcall+0x44/0x1d0) from [<c0008490>] (kernel_init+0xc0/0x11c)
[ 1.268040] [<c0008490>] (kernel_init+0xc0/0x11c) from [<c0706184>] (kernel_thread_exit+0x0/0x8)
[ 1.276813] ---[ end trace da227214a82491b7 ]---
[ 1.281412] ##########[detect_irq_handler]##########
[ 1.286450] [ JACK_DRIVER (sec_jack_probe,709) ] sec_jack_probe HWREV =7, 0x01=1 jack->low_active =1
[ 1.295636] [ JACK_DRIVER (jack_detect_change,389) ] Headset detached 0
[ 1.302264] [wake_unlock]Detach
[ 1.305614] NetWinder Floating Point Emulator V0.97 (extended precision)
[ 1.313559] ashmem: initialized
[ 1.333496] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 1.336838] msgmni has been set to 663
[ 1.340491] alg: No test for cipher_null (cipher_null-generic)
[ 1.346013] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 1.351874] alg: No test for digest_null (digest_null-generic)
[ 1.357681] alg: No test for compress_null (compress_null-generic)
[ 1.365733] alg: No test for stdrng (krng)
[ 1.420873] alg: No test for ghash (ghash-generic)
[ 1.424280] io scheduler noop registered
[ 1.428124] io scheduler anticipatory registered
[ 1.432703] io scheduler deadline registered
[ 1.437643] io scheduler cfq registered (default)
[ 1.443640] MDNIE INIT ..........
[ 1.445571] S3C MDNIE Driver, (c) 2010 Samsung Electronics
[ 1.451772] MDNIE INIT SUCCESS Addr : 0xe8838000
[ 1.455782] IELCD INIT ..........
[ 1.459118] S3C IELCD Driver, (c) 2010 Samsung Electronics
[ 1.465250] IELCD INIT SUCCESS Addr : 0xe8840000
[ 1.470183] s3cfb s3cfb: [fb0] dma: 0x4fc00000, cpu: 0xe8c00000, size: 0x002ee000
[ 1.478610] FIMD src sclk = 166750000
[ 1.480825] s3cfb s3cfb: registered successfully
[ 1.678474] s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 1.685885] s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 1.693887] s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 1.702008] s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 1.721239] brd: module loaded
[ 1.728267] loop: module loaded
[ 1.730088] pmem: 1 init
[ 1.734227] pmem_gpu1: 1 init
[ 1.737798] pmem_adsp: 1 init
[ 1.742068] [BIF:IN ] ++FSR_BML_Init(nFlag: 0x0)
[ 1.745404] [PAM: ] ++FSR_PAM_Init
[ 1.749714] [PAM: ] OneNAND physical base address : 0xb0000000
[ 1.755771] [PAM: ] OneNAND virtual base address : 0xe8880000
[ 1.762494] [PAM: ] OneNAND nMID=0xec : nDID=0x50 Page size=4
[ 1.768655] [PAM: ] --FSR_PAM_Init
[ 1.772318] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 1.777769] [OND:INF] FSR_OND_4K_Open(nDev:0, pParam:0xc4ff1e38, nFlag:0x00000000) / 1033 line
[ 1.786606] pstOND4kCxt->nBaseAddr: 0xe8880000
[ 1.792153] nDev=0, nMID=0x00ec, nDID=0x0050, nVID=0x013e
[ 1.798657] [OND:INF] pstOND4kCxt->nSysConf1:0xf006 / 1116 line
[ 1.804818] [OND:INF] pstOND4kCxt->nBlksForSLCArea[0]:2048 / 1133 line
[ 1.811588] [OND:INF] pstOND4kCxt->nIntID :0x0000 / 1236 line
[ 1.817735] [OND:INF] 1X_CACHEPGM CMD : 0x007f
[ 1.822423] [OND:INF] 1X_PLOAD CMD : 0x0003
[ 1.827374] [BBM:INF] Scan from 2004 to 2047 to find BML meta blocks (die: 0)
[ 1.834686] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.841625] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.848531] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.855475] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.862408] [BBM:INF] a5a5 a5a5 ffff
[ 1.901878] FSR: Registered TinyFSR Driver.
[ 1.907286] tl2796_probe::779->s6e63m0 probed successfuly
[ 1.911549] PPP generic driver version 2.4.2
[ 1.916491] PPP Deflate Compression module registered
[ 1.920528] PPP BSD Compression module registered
[ 1.926100] PPP MPPE Compression module registered
[ 1.930005] NET: Registered protocol family 24
[ 1.934429] PPPoL2TP kernel driver, V1.0
[ 1.938290] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 1.947917] CSLIP: code copyright 1989 Regents of the University of California.
[ 1.955306] [FSA9480] fsa9480_codec_probe
���Łfsa9480_interrupt
[ 2.524483] [FSA9480]----------DEBUG INT HENDLER--------------- fsa9480_interrupt
[ 2.531988] [FSA9480] FSA9480_ReadIntRegister
[ 2.536660] [audio_power, 333] AUDIO POWER COMPLETED : 1
[ 2.541944] [wm8994_i2c_probe, 2309]
[ 2.545587] [wm8994_init, 2120]
[ 2.550700] mmc0: switch to bus width 4
[ 2.552996] mmc0: new high speed MMC card at address 0001
[ 2.559064] mmcblk0: mmc0:0001 000000 1.86 GiB
[ 2.563300] mmcblk0: unknown partition table
[ 2.568203] Another host want the wakelock : 2
[ 2.579896] ldo38_control : turn ON LDO3 and LDO8 (cur_stat=0, req=1)
[ 2.584890] [otg_clock_enable] clk_enable(otg_clock) OK.
[ 2.591218] [udc_enable]AP_USB_Power off by Bootup : 1s3c_preallocate_dma_buffer: VA-ff001000, PA-4F860000, 131072bytes
[ 2.609233] s3c_preallocate_dma_buffer: VA-ff021000, PA-4F880000, 131072bytes
[ 2.616064] asoc: WM8994 PAIFRX <-> s3c64xx-i2s mapping ok
[ 2.621611] sound_tty procfs initialised
[ 2.625442] sound_tty procfs initialised
[ 2.633608] *** DEBUG : First we search for SDIO...(1)***
[ 2.638792] +++++++smdkc110_audio_init
[ 2.641408] *** DEBUG : ...then normal SD...(1) ***
[ 2.646476] [FSA9480] FSA9480_ProcessDevice (dev1 : 0x0, dev2 : 0x4)
[ 2.652481] FSA9480_DEV_TY2_JIG_UART_ON --- ATTACH
[ 2.657464] chk snd_soc_instantiate_card
[ 2.661152] chk snd_soc_instantiate_card: before for : DEBUG 1
[ 2.666958] chk snd_soc_instantiate_card: before !ac97 : DEBUG 2
[ 2.672934] chkerr snd_soc_instantiate_card: Problem card probe() is not defined
[ 2.680312] calling snd_soc_instantiate_card: cpu_dai->probe()
[ 2.687095] calling snd_soc_instantiate_card: codec_dev->probe()
[ 2.692150] WM8994 Audio Codec 0.1
[ 2.695487] [wm8994_pcm_init, 2218]
[ 2.700242] JIG UART ON
[ 2.702379] *** DEBUG : ...and finally MMC. (1)***
[ 2.706773] Another host want the wakelock : 1
[ 2.710846] Universal : Card status 1
[ 2.714652] mmc2: wake_lock_timeout 1sec 0
[ 2.752664] s3c_preallocate_dma_buffer: VA-ff041000, PA-4F8C0000, 131072bytes
[ 2.758618] s3c_preallocate_dma_buffer: VA-ff061000, PA-4F8E0000, 131072bytes
[ 2.765454] asoc: WM8994 PCM <-> s3c-pcmdev mapping ok
[ 2.772212] ASoC: Failed to create codec register debugfs file
[ 2.776612] Failed to create pop time debugfs file
[ 2.781363] Failed to create DAPM debugfs directory
[ 2.786217] chk snd_soc_instantiate_card
[ 2.790132] ----------smdkc110_audio_init
[ 2.794107] ALSA device list:
[ 2.797054] #0: smdkc110 (WM8994)
[ 2.800523] #1: smdkc110-pcm (WM8994)
[ 2.804746] Netfilter messages via NETLINK v0.30.
[ 2.809141] nf_conntrack version 0.5.0 (5311 buckets, 21244 max)
[ 2.815569] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 2.822401] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 2.830287] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.836833] xt_time: kernel timezone is -0000
[ 2.842514] IPv4 over IPv4 tunneling driver
[ 2.846903] GRE over IPv4 tunneling driver
[ 2.852638] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.856692] TCP cubic registered
[ 2.861093] NET: Registered protocol family 10
[ 2.873550] IPv6 over IPv4 tunneling driver
[ 2.880571] NET: Registered protocol family 17
[ 2.883586] NET: Registered protocol family 15
[ 2.888005] Bluetooth: L2CAP ver 2.14
[ 2.891619] Bluetooth: L2CAP socket layer initialized
[ 2.896666] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.901158] Bluetooth: SCO socket layer initialized
[ 2.906122] Bluetooth: RFCOMM TTY layer initialized
[ 2.910902] Bluetooth: RFCOMM socket layer initialized
[ 2.915999] Bluetooth: RFCOMM ver 1.11
[ 2.919906] NET: Registered protocol family 33
[ 2.924207] NET: Registered protocol family 35
[ 2.928733] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 2.937648] using rtc device, s3c, for alarms
[ 2.940433] s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
[ 2.950657] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 2.958221] melfas touchkey_init
[ 2.961602] EXT_I2C(244) -> No ACK
[ 2.964013] mcsdl_download_binary_data F/W version: 0xff, Module version:0xff
[ 2.970715] melfas i2c_touchkey_probe
[ 2.975728] input: melfas-touchkey as /devices/virtual/input/input2
[ 2.981990] i2c_touchkey_read 135 i2c transfer error
[ 2.985826] qt602240 GPIO Status
[ 2.988728] TOUCH_EN : High
[ 2.991570] TOUCH_RST : Low
[ 2.994343] TOUCH_INT : High
[ 3.100306] qt602240_i2c is attached..
[ 3.102583] +-----------------------------------------+
[ 3.107854] | Quantum Touch Driver Probe! |
[ 3.113016] +-----------------------------------------+
[ 3.118752] input: qt602240_ts_input as /devices/virtual/input/input3
[ 3.125492] QT_reprogram check
[ 3.127753] chkerr s3c24xx_i2c_doxfer, incomplete xfer -6
[ 3.133084] [QT] init_touch_driver start
[ 3.136948] [QT] init_I2C start
[ 3.165805]
[ 3.165810] [TSP] Touch device found
[ 3.169375] Version: 0x16
Family:169380] 0x80
Variant: 3734] 0x1
Build number: 0xab
Matrix X size : 19
Matrix Y size : 11
Calculated CRC: 0x1c 0x34 0xff 0x00
[ 3.195315]
Stored CRC:76] 0x1c 0x34 0xff 0x00
[ 3.201230]
Info block CRC value OK.
[ 3.204338]
[ 3.204342]
[ 3.209474] [TSP]qt_Power_Config_Init real board
[ 3.223015]
[ 3.223019] [TSP][reset_chip]
[ 3.329889] Chip reset OK!
[TSP] qt602240_probe: Start touchscreen qt602240_ts_input
[ 3.337649] qt602240_probe , 3665
[ 3.341263] [QT] ret : 0, qt602240->client name : qt602240_ts
[ 3.346768] [QT] qt602240_init/5837
[ 3.350459] [TSP] msg id = 1 90 8c d1 2 0 0 0 0
[ 3.354830] [TSP] quantum_msg[0] = 1 and quantum_msg[1] = 0x10 cal_check_flag=1
[ 3.362381] [QT] qt602240_init/5865, platform_driver_register!!
[ 3.369143] [TSP] msg id = 1 0 8c d1 2 0 0 0 0
[ 3.372665] [TSP] quantum_msg[0] = 1 and quantum_msg[1] = 0x00 cal_check_flag=2
[ 3.380523] s3c2410-rtc s3c2410-rtc: setting system clock to 2005-01-01 00:02:47 UTC (1104537767)
[ 3.391886] FIMC0 registered successfully
[ 3.397290] FIMC1 registered successfully
[ 3.402605] FIMC2 registered successfully
[ 3.405442] S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[ 3.416042] s5p-tvout s5p-tvout: hpd status is cable inserted
[ 3.421962] s3c_bat_init
[ 3.423075] Fuel guage attach success!!!
[ 3.427273] sec-battery sec-battery: s3c_bat_probe
[ 3.948059] s3c_bat_check_v_f: Battery auth. full check (Pass)
[ 3.953199] [BATT] s3c_cable_check_status
[ 4.470827] maxim_TA_connect~~~
[ 4.482524] maxim_TA_connect~~~
[ 4.484272] KERNEL:magic_number=0 CLEAR_UPLOAD_MAGIC_NUMBER
[ 4.490171] maxim_charging_control: TA charging enable
[ 4.495048] s3c_cable_check_status: status : AC
[ 4.499551] [BATT] s3c_cable_status_update
[ 4.503715] s3c_cable_status_update: cable AC
[ 4.508060] s3c_cable_status_update: call power_supply_changed
[ 4.519732] pmic interrupt registered
[ 4.524107] Freeing init memory: 7152K
[ 4.526439] Warning: unable to open an initial console.
[ 4.532680] [email protected] process: start parse init.rc
[ 4.537087] [email protected] process: drain_action_queue
[ 4.540521] [email protected] process: device_init #3
[ 5.022660] [BATT] maxim_vac_disconnect
[ 5.025440] maxim_vac_disconnect: connect status skip
[ 5.051149] [email protected] process: property_init
[ 5.069401] fsr: module license 'Samsung Proprietary' taints kernel.
[ 5.074314] Disabling lock debugging due to kernel taint
[ 5.114550] [BIF:IN ] ++FSR_BML_Init(nFlag: 0x0)
[ 5.117856] [PAM: ] ++FSR_PAM_Init
[ 5.122122] [PAM: ] OneNAND physical base address : 0xb0000000
[ 5.128254] [PAM: ] OneNAND virtual base address : 0xe8940000
[ 5.135630] [PAM: ] OneNAND Controller DMA physical base address : 0xb0600000
[ 5.143093] [PAM: ] OneNAND Controller DMA virtual base address : 0xe8980000
[ 5.151110] [PAM: ] OneNAND nMID=0xec : nDID=0x50 Page size=4
[ 5.157267] [PAM: ] --FSR_PAM_Init
[ 5.160992] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 5.166385] [OND:INF] FSR_OND_4K_Open(nDev:0, pParam:0xc4ff1e00, nFlag:0x00000000) / 1033 line
[ 5.175224] pstOND4kCxt->nBaseAddr: 0xe8940000
[ 5.180769] nDev=0, nMID=0x00ec, nDID=0x0050, nVID=0x013e
[ 5.187273] [OND:INF] pstOND4kCxt->nSysConf1:0xf006 / 1116 line
[ 5.193435] [OND:INF] pstOND4kCxt->nBlksForSLCArea[0]:2048 / 1133 line
[ 5.200217] [OND:INF] pstOND4kCxt->nIntID :0x0000 / 1236 line
[ 5.206353] [OND:INF] 1X_CACHEPGM CMD : 0x007f
[ 5.211038] [OND:INF] 1X_PLOAD CMD : 0x0003
[ 5.215891] [BBM:INF] Scan from 2004 to 2047 to find BML meta blocks (die: 0)
[ 5.223209] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.230116] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.237054] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.244011] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.250931] [BBM:INF] a5a5 a5a5 ffff
[ 5.275279] [BBM: ] << DevNO:0, DieNO: 0 MAPPING INFORMATION >>
[ 5.280081] [BBM: ] Bad Mark Information
[ 5.284423] [BBM: ] - Bad Mark (0x2222) by erase error
[ 5.290229] [BBM: ] - Bad Mark (0x4444) by write error
[ 5.296153] [BBM: ] 0000: Sbn[ 1213]==>Rbn[ 2042] / BadMark: 0x0000 / SLC / Lock: UL
[ 5.304176] [BBM: ] << Total : 1 BAD-MAPPING INFORMATION >>
[ 5.310178] [BIF: ] nPartition Information (nVol : 0)
Here is the UART output during normal boot.
Code:
-----------------------------------------------------------
Samsung Primitive Bootloader (PBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
-----------------------------------------------------------
+n1stVPN 2688
+nPgsPerBlk 64
+n1stVPN 3008
+nPgsPerBlk 64
PBL found bootable SBL: Partition(4).
Set cpu clk. from 400MHz to 800MHz.
IROM e-fused version.
-----------------------------------------------------------
Samsung Secondary Bootloader (SBL) v3.0
Copyright (C) Samsung Electronics Co., Ltd. 2006-2010
Board Name: ARIES REV 02
Build On: Oct 26 2010 14:22:42
-----------------------------------------------------------
Re_partition: magic code(0x0)
[PAM: ] ++FSR_PAM_Init
[PAM: ] OneNAND physical base address : 0xb0000000
[PAM: ] OneNAND virtual base address : 0xb0000000
[PAM: ] OneNAND nMID=0xec : nDID=0x50
[PAM: ] --FSR_PAM_Init
fsr_bml_load_partition: pi->nNumOfPartEntry = 12
partitions loading success
board partition information update.. source: 0x0
.Done.
read 1 units.
==== PARTITION INFORMATION ====
ID : IBL+PBL (0x0)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 0
NO_UNITS : 1
===============================
ID : PIT (0x1)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 1
NO_UNITS : 1
===============================
ID : EFS (0x14)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 2
NO_UNITS : 40
===============================
ID : SBL (0x3)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 42
NO_UNITS : 5
===============================
ID : SBL2 (0x4)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 47
NO_UNITS : 5
===============================
ID : PARAM (0x15)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 52
NO_UNITS : 20
===============================
ID : KERNEL (0x6)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 72
NO_UNITS : 30
===============================
ID : RECOVERY (0x7)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 102
NO_UNITS : 30
===============================
ID : FACTORYFS (0x16)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 132
NO_UNITS : 1286
===============================
ID : DBDATAFS (0x17)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1418
NO_UNITS : 444
===============================
ID : CACHE (0x18)
ATTR : RW STL SLC (0x1101)
FIRST_UNIT : 1862
NO_UNITS : 140
===============================
ID : MODEM (0xb)
ATTR : RO SLC (0x1002)
FIRST_UNIT : 2002
NO_UNITS : 2
===============================
loke_init: j4fs_open success..
load_lfs_parameters valid magic code and version.
load_debug_level reading debug level from file successfully(0x574f4c44).
quick_start- quick start is executed!
init_fuel_gauge: vcell = 3815mV, soc = 44
reading nps status file is successfully!.
nps status=0x504d4f43
PMIC_IRQ1 = 0xc0
PMIC_IRQ2 = 0x0
PMIC_IRQ3 = 0x1
PMIC_IRQ4 = 0x0
PMIC_STATUS1 = 0x40
PMIC_STATUS2 = 0x2c
get_debug_level current debug level is 0x574f4c44.
aries_process_platform: Debug Level Low
keypad_scan: key value ----------------->= 0x0
CONFIG_ARIES_REV:32 , CONFIG_ARIES_REV03:48
aries_process_platform: final s1 booting mode = 0
AST_POWERON..
DISPLAY_PATH_SEL[MDNIE 0x1]is on
MDNIE setting Init start!!
vsync interrupt is off
video interrupt is off
[fb0] turn on
MDNIE setting Init end!!
Autoboot (0 seconds) in progress, press any key to stop
get_debug_level current debug level is 0x574f4c44.
get_debug_level current debug level is 0x574f4c44.
boot_kernel: Debug Level Low
Load Partion idx = (6)
Loading Partion idx = (6)
..............................done
Kernel read success from kernel partition no.6, idx.6.
setting param.serialnr=0x32321357 0x21bb00ec
setting param.board_rev=0x20
setting param.cmdline=console=ttySAC2,115200 loglevel=9
Starting kernel at 0x32000000...
Uncompressing Linux...................................................................................................................................................................................
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32.9 ([email protected]) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 Fri Jul 8 18:12:14 KST 2011
[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: SMDKC110
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 20480
[ 0.000000] free_area_init_node: node 0, pgdat c1069aa8, node_mem_map c1240000
[ 0.000000] Normal zone: 160 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 20320 pages, LIFO batch:3
[ 0.000000] On node 1 totalpages: 65536
[ 0.000000] free_area_init_node: node 1, pgdat c106a160, node_mem_map d0002000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] On node 2 totalpages: 32768
[ 0.000000] free_area_init_node: node 2, pgdat c106a818, node_mem_map e0001000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32512 pages, LIFO batch:7
[ 0.000000] On node 3 totalpages: 0
[ 0.000000] free_area_init_node: node 3, pgdat c106aed0, node_mem_map c12e8c20
[ 0.000000] Normal zone: 1 pages exceeds realsize 0
[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110222)
[ 0.000000] s5pv210_init_clocks: initializing clocks
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] copy: bad source 0
[ 0.000000] mout_audss: bad source 0
[ 0.000000] s5pv210_setup_clocks: registering clocks
[ 0.000000] s5pv210_setup_clocks: clkdiv0 = 14131330, clkdiv1 = 00300400
[ 0.000000] s5pv210_setup_clocks: xtal is 24000000
[ 0.000000] S5PV210: PLL settings, A=800000000, M=667000000, E=96000000
[ 0.000000] s5pv210: 33554432 bytes system memory reserved for mfc at 0x312f3000
[ 0.000000] s5pv210: 33554432 bytes system memory reserved for mfc at 0x40204000
[ 0.000000] s5pv210: 12582912 bytes system memory reserved for fimc0 at 0x42204000
[ 0.000000] s5pv210: 1048576 bytes system memory reserved for fimc1 at 0x42e04000
[ 0.000000] s5pv210: 12582912 bytes system memory reserved for fimc2 at 0x42f04000
[ 0.000000] s5pv210: 2097152 bytes system memory reserved for pmem at 0x332f3000
[ 0.000000] s5pv210: 4194304 bytes system memory reserved for pmem_gpu1 at 0x334f3000
[ 0.000000] s5pv210: 1536000 bytes system memory reserved for pmem_adsp at 0x338f3000
[ 0.000000] s5pv210: 10485760 bytes system memory reserved for texstream at 0x33a6a000
[ 0.000000]
[ 0.000000] Skipping memset of fb base address 0x4fc00000 -------
[ 0.000000] s5pv210: 3145728 bytes system memory reserved for fimd at 0x4fc00000
[ 0.000000] s5pv210: 262144 bytes system memory reserved for wifi at 0x3446a000
[ 0.000000] Built 3 zonelists in Zone order, mobility grouping on. Total pages: 117856
[ 0.000000] Kernel command line: console=ttySAC2,115200 loglevel=9
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 80MB 256MB 128MB = 464MB total
[ 0.000000] Memory: 339468KB available (9240K code, 1899K data, 7152K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=4
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:339
[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41
[ 0.000000] mult[140737]
[ 0.000000] max_delta_ns[2147483647]
[ 0.000000] min_delta_ns[30517]
[ 0.000000] rate[32768]
[ 0.000000] HZ[256]
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC2] enabled
[ 0.366830] Calibrating delay loop... 796.20 BogoMIPS (lpj=1556480)
[ 0.450431] Mount-cache hash table entries: 512
[ 0.455292] Initializing cgroup subsys debug
[ 0.459135] Initializing cgroup subsys cpuacct
[ 0.463552] Initializing cgroup subsys freezer
[ 0.467998] CPU: Testing write buffer coherency: ok
[ 0.477132] KERNEL:kernel_sec_get_debug_level_from_boot=0x574f4c44
[ 0.481884] KERNEL:magic_number=0x0 DEBUG LEVEL low!!
[ 0.486879] (kernel_sec_set_upload_cause) : upload_cause set 0
[ 0.497624] regulator: core version 0.5
[ 0.500382] NET: Registered protocol family 16
[ 0.520423] S5PC110 Hardware version : EVT1
[ 0.524048] HWREV is 0x7
[ 0.526133] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.544098] aries_init_wifi_mem
[ 0.545796] aries_init_wifi_mem success
[ 0.549633] recovery_dev_register
[ 0.552883] create_recovery_class
[ 0.556540] S5PV210 Power Domain API Enable
[ 0.561300] S5PV210: Initializing architecture
[ 0.564813] S3C PL330-DMA Controller Driver, (c) 2008-2009 Samsung Electronics
[ 0.571966] Total 24 DMA channels will be initialized.
[ 0.578434] DMA: got clock for controller 0 and disabled
[ 0.583159] DMA: got clock for controller 1 and disabled
[ 0.588562] DMA: got clock for controller 2 and disabled
[ 0.594654] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
[ 0.601688] s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
[ 0.610077] s3c24xx-pwm s3c24xx-pwm.2: tin at 4168750, tdiv at 4168750, tin=divclk, base 12
[ 0.618401] s3c24xx-pwm s3c24xx-pwm.3: tin at 4168750, tdiv at 4168750, tin=divclk, base 16
[ 0.646359] bio: create slab <bio-0> at 0
[ 0.650209] vgaarb: loaded
[ 0.652490] SCSI subsystem initialized
[ 0.656544] i2c-gpio i2c-gpio.4: using pins 247 (SDA) and 246 (SCL)
[ 0.662091] i2c-gpio i2c-gpio.5: using pins 203 (SDA) and 204 (SCL)
[ 0.668812] regulator: DCDC1: 750 <--> 1500 mV
[ 0.672850] regulator: DCDC2: 750 <--> 1500 mV
[ 0.677566] regulator: LDO4: 3300 mV
[ 0.680962] regulator: LDO7: 1600 <--> 3600 mV
[ 0.685476] regulator: LDO17: 1600 <--> 3600 mV
[ 0.690153] i2c-gpio i2c-gpio.6: using pins 206 (SDA) and 209 (SCL)
[ 0.696318] i2c-gpio i2c-gpio.7: using pins 201 (SDA) and 202 (SCL)
[ 0.702771] i2c-gpio i2c-gpio.8: using pins 42 (SDA) and 43 (SCL)
[ 0.708634] i2c-gpio i2c-gpio.9: using pins 245 (SDA) and 244 (SCL)
[ 0.714930] i2c-gpio i2c-gpio.10: using pins 197 (SDA) and 198 (SCL)
[ 0.721221] i2c-gpio i2c-gpio.11: using pins 114 (SDA) and 98 (SCL)
[ 0.727255] i2c-gpio i2c-gpio.12: using pins 173 (SDA) and 172 (SCL)
[ 0.735227] s3c-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
[ 0.740445] s3c-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
[ 0.746147] s3c-i2c s3c2410-i2c.2: i2c-2: S3C I2C adapter
[ 0.751911] Bluetooth: Core ver 2.15
[ 0.754274] NET: Registered protocol family 31
[ 0.758515] Bluetooth: HCI device and connection manager initialized
[ 0.764780] Bluetooth: HCI socket layer initialized
[ 0.770034] Switching to clocksource clock_source_systimer
[ 0.784946] NET: Registered protocol family 2
[ 0.788294] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.796108] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.802317] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[ 0.809083] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.815081] TCP reno registered
[ 0.818420] NET: Registered protocol family 1
[ 0.854755] [BT] rfkill_register(bt_rfk)
[ 0.857679] [BT] Device Powering ON
[ 0.860857] [BT] GPIO_BT_nRST = 0
[ 0.864166] [BT] bt_host_wake_irq_handler start
[ 0.868718] [BT] GPIO_WLAN_BT_EN = 1
[ 0.974454] [BT] GPIO_BT_nRST = 1
[ 0.976451] [BT] Device Powering OFF
[ 0.979958] [BT] bt_host_wake_irq_handler start
[ 0.984463] [BT] GPIO_BT_nRST = 0
[ 0.987754] [BT] GPIO_WLAN_BT_EN = 0
[ 0.991626] [BT] bt_host_wake_irq_handler start
[ 0.996178] [BT] In the unblocked state of the sleep
[ 1.000791] [BT] GPIO_BT_WAKE = 0
[ 1.004059] [BT] wake_unlock(bt_wake_lock)
[ 1.008199] [BT] In the unblocked state of the sleep
[ 1.013095] [BT] GPIO_BT_WAKE = 0
[ 1.016375] [BT] wake_unlock(bt_wake_lock)
[ 1.020449] [BT] bt_host_wake_irq_handler start
[ 1.025281] S5PC11X_FREQ_TAB=0 , S5PC11X_MAXFREQLEVEL=4
[ 1.030516] S5PV210 ADC driver, (c) 2010 Samsung Electronics
[ 1.037487] [ JACK_DRIVER (sec_jack_init,791) ]
[ 1.040686] SEC HEADSET: Registering headset driver
[ 1.045926] input: sec_jack as /devices/virtual/input/input0
[ 1.051177] [ JACK_DRIVER (sec_jack_probe,631) ] registering switch_sendend switch_dev sysfs sec_jack
[ 1.060729] SISO:registering switch_sendend switch_dev
[ 1.066069] ##########[send_end_irq_handler irq : headset_state : 0 ]##########
[ 1.072933] [ JACK_DRIVER (sec_jack_probe,671) ] sended isr send=0Xbe, ret =0
[ 1.079956] ##########[detect_irq_handler]##########
[ 1.084991] [ JACK_DRIVER (sec_jack_probe,688) ] detect isr send=0X26, ret =0
[ 1.092089] ------------[ cut here ]------------
Code:
[ 1.096674] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x64/0x130()
[ 1.104464] autorequest GPIO-208
[ 1.107673] Modules linked in:
[ 1.110742] [<c070cb70>] (unwind_backtrace+0x0/0xf4) from [<c0b81de8>] (dump_stack+0x20/0x24)
[ 1.119226] [<c0b81de8>] (dump_stack+0x20/0x24) from [<c074451c>] (warn_slowpath_common+0x60/0x70)
[ 1.128153] [<c074451c>] (warn_slowpath_common+0x60/0x70) from [<c0744588>] (warn_slowpath_fmt+0x38/0x40)
[ 1.137693] [<c0744588>] (warn_slowpath_fmt+0x38/0x40) from [<c08c6f70>] (gpio_ensure_requested+0x64/0x130)
[ 1.147407] [<c08c6f70>] (gpio_ensure_requested+0x64/0x130) from [<c08c70e4>] (gpio_direction_output+0xa8/0x118)
[ 1.157560] [<c08c70e4>] (gpio_direction_output+0xa8/0x118) from [<c0718e9c>] (sec_jack_probe+0x314/0x4f0)
[ 1.167188] [<c0718e9c>] (sec_jack_probe+0x314/0x4f0) from [<c091f8c4>] (platform_drv_probe+0x28/0x2c)
[ 1.176463] [<c091f8c4>] (platform_drv_probe+0x28/0x2c) from [<c091e3e8>] (driver_probe_device+0x8c/0x17c)
[ 1.186089] [<c091e3e8>] (driver_probe_device+0x8c/0x17c) from [<c091e574>] (__driver_attach+0x9c/0xa0)
[ 1.195456] [<c091e574>] (__driver_attach+0x9c/0xa0) from [<c091da80>] (bus_for_each_dev+0x70/0x9c)
[ 1.204476] [<c091da80>] (bus_for_each_dev+0x70/0x9c) from [<c091e25c>] (driver_attach+0x2c/0x30)
[ 1.213322] [<c091e25c>] (driver_attach+0x2c/0x30) from [<c091d180>] (bus_add_driver+0xd8/0x328)
[ 1.222082] [<c091d180>] (bus_add_driver+0xd8/0x328) from [<c091e880>] (driver_register+0x88/0x19c)
[ 1.231104] [<c091e880>] (driver_register+0x88/0x19c) from [<c091fe60>] (platform_driver_register+0x60/0x68)
[ 1.240908] [<c091fe60>] (platform_driver_register+0x60/0x68) from [<c000f978>] (sec_jack_init+0x2c/0x34)
[ 1.250451] [<c000f978>] (sec_jack_init+0x2c/0x34) from [<c07043f4>] (do_one_initcall+0x44/0x1d0)
[ 1.259291] [<c07043f4>] (do_one_initcall+0x44/0x1d0) from [<c0008490>] (kernel_init+0xc0/0x11c)
[ 1.268050] [<c0008490>] (kernel_init+0xc0/0x11c) from [<c0706184>] (kernel_thread_exit+0x0/0x8)
[ 1.276823] ---[ end trace da227214a82491b7 ]---
[ 1.281421] ##########[detect_irq_handler]##########
[ 1.286459] [ JACK_DRIVER (sec_jack_probe,709) ] sec_jack_probe HWREV =7, 0x01=1 jack->low_active =1
[ 1.295644] [ JACK_DRIVER (jack_detect_change,389) ] Headset detached 0
[ 1.302273] [wake_unlock]Detach
[ 1.305622] NetWinder Floating Point Emulator V0.97 (extended precision)
[ 1.313573] ashmem: initialized
[ 1.333511] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 1.336855] msgmni has been set to 663
[ 1.340509] alg: No test for cipher_null (cipher_null-generic)
[ 1.346032] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 1.351890] alg: No test for digest_null (digest_null-generic)
[ 1.357700] alg: No test for compress_null (compress_null-generic)
[ 1.365753] alg: No test for stdrng (krng)
[ 1.420885] alg: No test for ghash (ghash-generic)
[ 1.424288] io scheduler noop registered
[ 1.428132] io scheduler anticipatory registered
[ 1.432712] io scheduler deadline registered
[ 1.437655] io scheduler cfq registered (default)
[ 1.443650] MDNIE INIT ..........
[ 1.445580] S3C MDNIE Driver, (c) 2010 Samsung Electronics
[ 1.451789] MDNIE INIT SUCCESS Addr : 0xe8838000
[ 1.455792] IELCD INIT ..........
[ 1.459127] S3C IELCD Driver, (c) 2010 Samsung Electronics
[ 1.465251] IELCD INIT SUCCESS Addr : 0xe8840000
[ 1.470200] s3cfb s3cfb: [fb0] dma: 0x4fc00000, cpu: 0xe8c00000, size: 0x002ee000
[ 1.478616] FIMD src sclk = 166750000
[ 1.480818] s3cfb s3cfb: registered successfully
[ 1.678695] s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
[ 1.686097] s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
[ 1.694109] s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
[ 1.702225] s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
[ 1.721428] brd: module loaded
[ 1.728517] loop: module loaded
[ 1.730259] pmem: 1 init
[ 1.734662] pmem_gpu1: 1 init
[ 1.738024] pmem_adsp: 1 init
[ 1.742264] [BIF:IN ] ++FSR_BML_Init(nFlag: 0x0)
[ 1.745586] [PAM: ] ++FSR_PAM_Init
[ 1.749902] [PAM: ] OneNAND physical base address : 0xb0000000
[ 1.755979] [PAM: ] OneNAND virtual base address : 0xe8880000
[ 1.762693] [PAM: ] OneNAND nMID=0xec : nDID=0x50 Page size=4
[ 1.768848] [PAM: ] --FSR_PAM_Init
[ 1.772521] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 1.777974] [OND:INF] FSR_OND_4K_Open(nDev:0, pParam:0xc4ff1e38, nFlag:0x00000000) / 1033 line
[ 1.786801] pstOND4kCxt->nBaseAddr: 0xe8880000
[ 1.792365] nDev=0, nMID=0x00ec, nDID=0x0050, nVID=0x013e
[ 1.798857] [OND:INF] pstOND4kCxt->nSysConf1:0xf006 / 1116 line
[ 1.805013] [OND:INF] pstOND4kCxt->nBlksForSLCArea[0]:2048 / 1133 line
[ 1.811789] [OND:INF] pstOND4kCxt->nIntID :0x0000 / 1236 line
[ 1.817935] [OND:INF] 1X_CACHEPGM CMD : 0x007f
[ 1.822618] [OND:INF] 1X_PLOAD CMD : 0x0003
[ 1.827579] [BBM:INF] Scan from 2004 to 2047 to find BML meta blocks (die: 0)
[ 1.834886] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.841811] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.848731] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.855670] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 1.862614] [BBM:INF] a5a5 a5a5 ffff
[ 1.901951] FSR: Registered TinyFSR Driver.
[ 1.907358] tl2796_probe::779->s6e63m0 probed successfuly
[ 1.911602] PPP generic driver version 2.4.2
[ 1.916526] PPP Deflate Compression module registered
[ 1.920628] PPP BSD Compression module registered
[ 1.926163] PPP MPPE Compression module registered
[ 1.930066] NET: Registered protocol family 24
[ 1.934503] PPPoL2TP kernel driver, V1.0
[ 1.938360] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 1.947981] CSLIP: code copyright 1989 Regents of the University of California.
[ 1.955379] [FSA9480] fsa9480_codec_probe
S�S2�ͅ�480_interrupt
[ 2.524145] [FSA9480]----------DEBUG INT HENDLER--------------- fsa9480_interrupt
[ 2.531655] [FSA9480] FSA9480_ReadIntRegister
[ 2.536324] [audio_power, 333] AUDIO POWER COMPLETED : 1
[ 2.541600] [wm8994_i2c_probe, 2309]
[ 2.545255] [wm8994_init, 2120]
[ 2.550363] mmc0: switch to bus width 4
[ 2.552658] mmc0: new high speed MMC card at address 0001
[ 2.558721] mmcblk0: mmc0:0001 000000 1.86 GiB
[ 2.562967] mmcblk0: unknown partition table
[ 2.567815] Another host want the wakelock : 2
[ 2.579904] ldo38_control : turn ON LDO3 and LDO8 (cur_stat=0, req=1)
[ 2.584900] [otg_clock_enable] clk_enable(otg_clock) OK.
[ 2.591222] [udc_enable]AP_USB_Power off by Bootup : 1s3c_preallocate_dma_buffer: VA-ff001000, PA-4F860000, 131072bytes
[ 2.609238] s3c_preallocate_dma_buffer: VA-ff021000, PA-4F880000, 131072bytes
[ 2.616078] asoc: WM8994 PAIFRX <-> s3c64xx-i2s mapping ok
[ 2.621621] sound_tty procfs initialised
[ 2.625451] sound_tty procfs initialised
[ 2.633607] *** DEBUG : First we search for SDIO...(1)***
[ 2.638775] +++++++smdkc110_audio_init
[ 2.641403] *** DEBUG : ...then normal SD...(1) ***
[ 2.646532] [FSA9480] FSA9480_ProcessDevice (dev1 : 0x0, dev2 : 0x4)
[ 2.652473] FSA9480_DEV_TY2_JIG_UART_ON --- ATTACH
[ 2.657428] chk snd_soc_instantiate_card
[ 2.661152] chk snd_soc_instantiate_card: before for : DEBUG 1
[ 2.666953] chk snd_soc_instantiate_card: before !ac97 : DEBUG 2
[ 2.672940] chkerr snd_soc_instantiate_card: Problem card probe() is not defined
[ 2.680308] calling snd_soc_instantiate_card: cpu_dai->probe()
[ 2.687093] calling snd_soc_instantiate_card: codec_dev->probe()
[ 2.692159] WM8994 Audio Codec 0.1
[ 2.695488] [wm8994_pcm_init, 2218]
[ 2.700236] JIG UART ON
[ 2.702380] *** DEBUG : ...and finally MMC. (1)***
[ 2.706777] Another host want the wakelock : 1
[ 2.710848] Universal : Card status 1
[ 2.714653] mmc2: wake_lock_timeout 1sec 0
[ 2.752666] s3c_preallocate_dma_buffer: VA-ff041000, PA-4F8C0000, 131072bytes
[ 2.758618] s3c_preallocate_dma_buffer: VA-ff061000, PA-4F8E0000, 131072bytes
[ 2.765459] asoc: WM8994 PCM <-> s3c-pcmdev mapping ok
[ 2.772192] ASoC: Failed to create codec register debugfs file
[ 2.776586] Failed to create pop time debugfs file
[ 2.781343] Failed to create DAPM debugfs directory
[ 2.786191] chk snd_soc_instantiate_card
[ 2.790102] ----------smdkc110_audio_init
[ 2.794081] ALSA device list:
[ 2.797034] #0: smdkc110 (WM8994)
[ 2.800498] #1: smdkc110-pcm (WM8994)
[ 2.804721] Netfilter messages via NETLINK v0.30.
[ 2.809110] nf_conntrack version 0.5.0 (5311 buckets, 21244 max)
[ 2.815546] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 2.822374] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 2.830249] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.836818] xt_time: kernel timezone is -0000
[ 2.842487] IPv4 over IPv4 tunneling driver
[ 2.846879] GRE over IPv4 tunneling driver
[ 2.852614] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.856666] TCP cubic registered
[ 2.861099] NET: Registered protocol family 10
[ 2.873483] IPv6 over IPv4 tunneling driver
[ 2.880474] NET: Registered protocol family 17
[ 2.883485] NET: Registered protocol family 15
[ 2.887915] Bluetooth: L2CAP ver 2.14
[ 2.891524] Bluetooth: L2CAP socket layer initialized
[ 2.896566] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.901063] Bluetooth: SCO socket layer initialized
[ 2.906034] Bluetooth: RFCOMM TTY layer initialized
[ 2.910809] Bluetooth: RFCOMM socket layer initialized
[ 2.915899] Bluetooth: RFCOMM ver 1.11
[ 2.919850] NET: Registered protocol family 33
[ 2.924107] NET: Registered protocol family 35
[ 2.928638] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 2.937564] using rtc device, s3c, for alarms
[ 2.940348] s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
[ 2.950585] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 2.958136] melfas touchkey_init
[ 2.961520] EXT_I2C(244) -> No ACK
[ 2.963935] mcsdl_download_binary_data F/W version: 0xff, Module version:0xff
[ 2.970631] melfas i2c_touchkey_probe
[ 2.975658] input: melfas-touchkey as /devices/virtual/input/input2
[ 2.981917] i2c_touchkey_read 135 i2c transfer error
[ 2.985737] qt602240 GPIO Status
[ 2.988652] TOUCH_EN : High
[ 2.991492] TOUCH_RST : Low
[ 2.994272] TOUCH_INT : High
[ 3.100251] qt602240_i2c is attached..
[ 3.102532] +-----------------------------------------+
[ 3.107799] | Quantum Touch Driver Probe! |
[ 3.112957] +-----------------------------------------+
[ 3.118706] input: qt602240_ts_input as /devices/virtual/input/input3
[ 3.125439] QT_reprogram check
[ 3.127701] chkerr s3c24xx_i2c_doxfer, incomplete xfer -6
[ 3.133026] [QT] init_touch_driver start
[ 3.136902] [QT] init_I2C start
[ 3.165812]
[ 3.165817] [TSP] Touch device found
[ 3.169384] Version: 0x16
Family:169389] 0x80
Variant: 3749] 0x1
Build number: 0xab
Matrix X size : 19
Matrix Y size : 11
Calculated CRC: 0x1c 0x34 0xff 0x00
[ 3.195324]
Stored CRC:86] 0x1c 0x34 0xff 0x00
[ 3.201239]
Info block CRC value OK.
[ 3.204347]
[ 3.204351]
[ 3.209488] [TSP]qt_Power_Config_Init real board
[ 3.223018]
[ 3.223023] [TSP][reset_chip]
[ 3.329927] Chip reset OK!
[TSP] qt602240_probe: Start touchscreen qt602240_ts_input
[ 3.337690] qt602240_probe , 3665
[ 3.341297] [QT] ret : 0, qt602240->client name : qt602240_ts
[ 3.346799] [QT] qt602240_init/5837
[ 3.350491] [TSP] msg id = 1 90 8c d1 2 0 0 0 0
[ 3.354869] [TSP] quantum_msg[0] = 1 and quantum_msg[1] = 0x10 cal_check_flag=1
[ 3.362412] [QT] qt602240_init/5865, platform_driver_register!!
[ 3.369179] [TSP] msg id = 1 0 8c d1 2 0 0 0 0
[ 3.372700] [TSP] quantum_msg[0] = 1 and quantum_msg[1] = 0x00 cal_check_flag=2
[ 3.380552] s3c2410-rtc s3c2410-rtc: setting system clock to 2005-01-01 00:05:28 UTC (1104537928)
[ 3.391929] FIMC0 registered successfully
[ 3.397335] FIMC1 registered successfully
[ 3.402648] FIMC2 registered successfully
[ 3.405493] S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
[ 3.416062] s5p-tvout s5p-tvout: hpd status is cable inserted
[ 3.421987] s3c_bat_init
[ 3.423111] Fuel guage attach success!!!
[ 3.427300] sec-battery sec-battery: s3c_bat_probe
[ 3.948049] s3c_bat_check_v_f: Battery auth. full check (Pass)
[ 3.953191] [BATT] s3c_cable_check_status
[ 4.470831] maxim_TA_connect~~~
[ 4.482560] maxim_TA_connect~~~
[ 4.484307] KERNEL:magic_number=0 CLEAR_UPLOAD_MAGIC_NUMBER
[ 4.490207] maxim_charging_control: TA charging enable
[ 4.495078] s3c_cable_check_status: status : AC
[ 4.499592] [BATT] s3c_cable_status_update
[ 4.503750] s3c_cable_status_update: cable AC
[ 4.508095] s3c_cable_status_update: call power_supply_changed
[ 4.519474] pmic interrupt registered
[ 4.523847] Freeing init memory: 7152K
[ 4.526176] Warning: unable to open an initial console.
[ 4.532410] [email protected] process: start parse init.rc
[ 4.538072] init: /init.rc: 385: invalid option 'ioprio'
[ 4.542519] init: /init.rc: 514: invalid option 'chmod'
[ 4.547144] init: /init.rc: 514: invalid option 'chmod'
[ 4.552349] init: /init.rc: 514: invalid option 'chmod'
[ 4.557555] init: /init.rc: 514: invalid option 'chmod'
[ 4.563082] [email protected] process: drain_action_queue
[ 4.567177] [email protected] process: device_init #3
[ 5.022236] [BATT] maxim_vac_disconnect
[ 5.024985] maxim_vac_disconnect: connect status skip
[ 5.078518] [email protected] process: property_init
[ 5.096756] fsr: module license 'Samsung Proprietary' taints kernel.
[ 5.101661] Disabling lock debugging due to kernel taint
[ 5.141891] [BIF:IN ] ++FSR_BML_Init(nFlag: 0x0)
[ 5.145215] [PAM: ] ++FSR_PAM_Init
[ 5.149462] [PAM: ] OneNAND physical base address : 0xb0000000
[ 5.155601] [PAM: ] OneNAND virtual base address : 0xe8940000
[ 5.162986] [PAM: ] OneNAND Controller DMA physical base address : 0xb0600000
[ 5.170433] [PAM: ] OneNAND Controller DMA virtual base address : 0xe8980000
[ 5.178457] [PAM: ] OneNAND nMID=0xec : nDID=0x50 Page size=4
[ 5.184616] [PAM: ] --FSR_PAM_Init
[ 5.188341] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 5.193733] [OND:INF] FSR_OND_4K_Open(nDev:0, pParam:0xc4ff1e00, nFlag:0x00000000) / 1033 line
[ 5.202570] pstOND4kCxt->nBaseAddr: 0xe8940000
[ 5.208115] nDev=0, nMID=0x00ec, nDID=0x0050, nVID=0x013e
[ 5.214620] [OND:INF] pstOND4kCxt->nSysConf1:0xf006 / 1116 line
[ 5.220782] [OND:INF] pstOND4kCxt->nBlksForSLCArea[0]:2048 / 1133 line
[ 5.227563] [OND:INF] pstOND4kCxt->nIntID :0x0000 / 1236 line
[ 5.233705] [OND:INF] 1X_CACHEPGM CMD : 0x007f
[ 5.238381] [OND:INF] 1X_PLOAD CMD : 0x0003
[ 5.243239] [BBM:INF] Scan from 2004 to 2047 to find BML meta blocks (die: 0)
[ 5.250556] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.257462] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.264401] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.271358] [BBM:INF] ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
[ 5.278278] [BBM:INF] a5a5 a5a5 ffff
[ 5.302629] [BBM: ] << DevNO:0, DieNO: 0 MAPPING INFORMATION >>
[ 5.307442] [BBM: ] Bad Mark Information
[ 5.311774] [BBM: ] - Bad Mark (0x2222) by erase error
[ 5.317585] [BBM: ] - Bad Mark (0x4444) by write error
[ 5.323514] [BBM: ] 0000: Sbn[ 1213]==>Rbn[ 2042] / BadMark: 0x0000 / SLC / Lock: UL
[ 5.331532] [BBM: ] << Total : 1 BAD-MAPPING INFORMATION >>
[ 5.337535] [BIF: ] nPartition Information (nVol : 0)
[ 5.343004] nVer : 0x10000
[ 5.346817] 00 / nID:0x00 / nAttr:0x00001002 / 1stVun: 0 / Units: 1
[ 5.354710] 01 / nID:0x01 / nAttr:0x00001002 / 1stVun: 1 / Units: 1
[ 5.362608] 02 / nID:0x20 / nAttr:0x00001101 / 1stVun: 2 / Units: 40
[ 5.370495] 03 / nID:0x03 / nAttr:0x00001002 / 1stVun: 42 / Units: 5
[ 5.378392] 04 / nID:0x04 / nAttr:0x00001002 / 1stVun: 47 / Units: 5
[ 5.386283] 05 / nID:0x21 / nAttr:0x00001101 / 1stVun: 52 / Units: 20
[ 5.394173] 06 / nID:0x06 / nAttr:0x00001002 / 1stVun: 72 / Units: 30
[ 5.402070] 07 / nID:0x07 / nAttr:0x00001002 / 1stVun: 102 / Units: 30
[ 5.409961] 08 / nID:0x22 / nAttr:0x00001101 / 1stVun: 132 / Units: 1286
[ 5.417856] 09 / nID:0x23 / nAttr:0x00001101 / 1stVun: 1418 / Units: 444
[ 5.425743] 10 / nID:0x24 / nAttr:0x00001101 / 1stVun: 1862 / Units: 140
[ 5.433646] 11 / nID:0x11 / nAttr:0x00001002 / 1stVun: 2002 / Units: 2
[ 5.441531] [BBM:INF] The registered blocks in ERL are handled
[ 5.447597] [BBM:INF] (number of blocks: 0)
[ 5.466270] BML: Registered BML Driver.
[ 5.507518] [BIF:IN ] ++FSR_BML_Init(nFlag: 0x0)
[ 5.510960] [BIF: ] FSR_BML_Init(nFlag:0x0, nRe:FSR_BML_ALREADY_INITIALIZED) / 1027 line
[ 5.529021] FSR: Registered STL Driver.
[ 5.703758] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 5.707871] [BIF: ] FSR_BML_Open(nVol:0, nFlag:0x0, nOpenCnt:2) / 1171 line
[ 5.715227] [SIF:INF] ===> STL Clst[ 1] Scan Root Info
[ 5.721152] [SIF:INF] ===> STL Zone[ 1, 0] Open Zone Meta
[ 5.727040] [SIF:INF] Latest Header Index ( 0) Vbn ( 2)
[ 5.733620] [SIF:INF] Latest Header Clean Page Offset ( 3)
[ 5.740072] [SIF:INF] POR write timer : 0xa
[ 5.744971] [SIF:INF] Latest Context BlockIdx ( 0) Offset ( 2) Vpn ( 130)
[ 5.753116] [SIF:INF] Number of Free Block ( 4)
[ 5.758630] [SIF:INF] Active Log List : Num ( 2)
[ 5.764265] [SIF:INF] ===> STL Zone[ 1, 0] Open Zone Post
[ 5.770130] [SIF:INF] ===> STL Zone[ 1, 0] Validity check
[ 5.775554] [SIF:INF] Partition [0, 21] open is success
[ 5.781767] [SIF:INF] Zone[ 1, 0]: nDgn( 4) nVbn( 8) S( 0)-E( 2) nCPOffs( 3)
[ 5.795662] [SIF:INF] Zone[ 1, 0]: nDgn( 2) nVbn( 15) S( 0)-E( 5) nCPOffs( 6)
[ 5.813939] param_init
[ 5.820327] load_lfs_param_value: param.blk read successfully.
[ 5.842194] pdp_activate, id: 1
[ 5.844457] ttyCSD(id: 1) serial device is created.
[ 5.848799] pdp_activate, id: 7
[ 5.852441] ttyCDMA(id: 7) serial device is created.
[ 5.856853] pdp_activate, id: 9
[ 5.860479] ttyTRFB(id: 9) serial device is created.
[ 5.864914] pdp_activate, id: 27
[ 5.868643] ttyCIQ(id: 27) serial device is created.
continued....
Code:
[ 5.874886] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 5.888633] [FSA9480]connectivity_switching_init = switch_sel : 0x198f
[ 5.893764] [FSA9480_Enable_AP_USB] Enable AP USB
[ 5.899245] [ap_usb_power_on]AP USB Power ON, askon: 0, mtp : 0
[ 5.904294] !!!!!!!!!!! [ap_usb_power_on]AP samsung_kies_mtp_mode_flag0, mtp:0
[ 5.921781] [enable_adb] enable(1), dev->adb_enabled(0)
[ 5.925545] [enable_adb]USBSTATUS_SAMSUNG_KIES
[ 5.929962] [enable_adb] change usb config to UMS + CDFS (No Debugging mode)
[ 5.937081] [usb_change_config] list_del 'UMS Only (No debugging mode)'
[ 5.943667] mass_storage_function_config_changed
[ 5.948266] interface 0 = usb_mass_storage/c4adfa00
[ 5.953824] [ap_usb_power_on]AP USB Power ON, askon: 0, mtp : 0
[ 5.959193] !!!!!!!!!!! [ap_usb_power_on]AP samsung_kies_mtp_mode_flag0, mtp:0
[ 5.966394] ldo38_control : turn ON LDO3 and LDO8 (cur_stat=1, req=1)
[ 5.972823] [otg_clock_enable] already clk_enabled.
[ 5.983767] [otg_clock_enable] clk_disable(otg_clock) OK.
[ 5.987707] ldo38_control : turn OFF LDO3 and LDO8 (cur_stat=1, req=1)
[ 5.998078] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 6.002164] [BIF: ] FSR_BML_Open(nVol:0, nFlag:0x0, nOpenCnt:3) / 1171 line
[ 6.009495] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 6.016043] [SIF:INF] ===> STL Clst[ 2] Scan Root Info
[ 6.021961] [SIF:INF] ===> STL Zone[ 2, 0] Open Zone Meta
[ 6.034897] [SIF:INF] Latest Header Index ( 13) Vbn ( 15)
[ 6.041314] [SIF:INF] Latest Header Clean Page Offset ( 7)
[ 6.047338] [SIF:INF] POR write timer : 0x4
[ 6.052486] [SIF:INF] Latest Context BlockIdx ( 13) Offset ( 6) Vpn ( 966)
[ 6.060391] [SIF:INF] Number of Free Block ( 25)
[ 6.065898] [SIF:INF] Active Log List : Num ( 0)
[ 6.071536] [SIF:INF] ===> STL Zone[ 2, 0] Open Zone Post
[ 6.077181] [SIF:INF] ===> STL Zone[ 2, 0] Validity check
[ 6.082824] [SIF:INF] Partition [0, 22] open is success
[ 6.089425] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 6.093757] [BIF: ] FSR_BML_Open(nVol:0, nFlag:0x0, nOpenCnt:4) / 1171 line
[ 6.101139] [SIF:INF] ===> STL Clst[ 3] Scan Root Info
[ 6.107051] [SIF:INF] ===> STL Zone[ 3, 0] Open Zone Meta
[ 6.113654] [SIF:INF] Latest Header Index ( 7) Vbn ( 9)
[ 6.124580] [SIF:INF] Latest Header Clean Page Offset ( 39)
[ 6.129994] [SIF:INF] POR write timer : 0x5
[ 6.134900] [SIF:INF] Latest Context BlockIdx ( 7) Offset ( 38) Vpn ( 614)
[ 6.143051] [SIF:INF] Number of Free Block ( 23)
[ 6.148559] [SIF:INF] Active Log List : Num ( 8)
[ 6.154192] [SIF:INF] ===> STL Zone[ 3, 0] Open Zone Post
[ 6.160694] [SIF:INF] ===> STL Zone[ 3, 0] Validity check
[ 6.165477] [SIF:INF] Partition [0, 23] open is success
[ 6.172783] [SIF:INF] Zone[ 3, 0]: nDgn( 0) nVbn( 33) S( 0)-E( 10) nCPOffs( 11)
[ 6.180112] [FSA9480]connectivity_switching_init = switch_sel : 0x198f
[ 6.186288] [SIF:INF] Zone[ 3, 0]: nDgn( 5) nVbn( 86) S( 53)-E( 52) nCPOffs( 53)
[ 6.202189] [SIF:INF] Zone[ 3, 0]: nDgn( 4) nVbn( 23) S( 0)-E( 55) nCPOffs( 56)
[ 6.210114] [SIF:INF] Zone[ 3, 0]: nDgn( 1) nVbn( 37) S( 0)-E( 5) nCPOffs( 6)
[ 6.228984] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 6.233030] [BIF: ] FSR_BML_Open(nVol:0, nFlag:0x0, nOpenCnt:5) / 1171 line
[ 6.240424] [SIF:INF] ===> STL Clst[ 4] Scan Root Info
[ 6.246333] [SIF:INF] ===> STL Zone[ 4, 0] Open Zone Meta
[ 6.252291] [SIF:INF] Latest Header Index ( 1) Vbn ( 3)
[ 6.258968] [SIF:INF] Latest Header Clean Page Offset ( 4)
[ 6.265280] [SIF:INF] POR write timer : 0x9
[ 6.270184] [SIF:INF] Latest Context BlockIdx ( 1) Offset ( 3) Vpn ( 195)
[ 6.278335] [SIF:INF] Number of Free Block ( 17)
[ 6.283839] [SIF:INF] Active Log List : Num ( 4)
[ 6.289474] [SIF:INF] ===> STL Zone[ 4, 0] Open Zone Post
[ 6.295563] [SIF:INF] ===> STL Zone[ 4, 0] Validity check
[ 6.300761] [SIF:INF] Partition [0, 24] open is success
[ 6.307186] [SIF:INF] Zone[ 4, 0]: nDgn( 0) nVbn( 27) S( 0)-E( 3) nCPOffs( 4)
[ 6.314910] [SIF:INF] Zone[ 4, 0]: nDgn( 4) nVbn( 28) S( 0)-E( 0) nCPOffs( 1)
[ 6.332238] [SIF:INF] Zone[ 4, 0]: nDgn( 2) nVbn( 25) S( 0)-E( 28) nCPOffs( 29)
[ 6.345842] [BIF: ] FSR VERSION: FSR_1.2.1p1_b139_RTM
[ 6.349890] [BIF: ] FSR_BML_Open(nVol:0, nFlag:0x0, nOpenCnt:6) / 1171 line
[ 6.357275] [SIF:INF] ===> STL Clst[ 0] Scan Root Info
[ 6.363195] [SIF:INF] ===> STL Zone[ 0, 0] Open Zone Meta
[ 6.369141] [SIF:INF] Latest Header Index ( 2) Vbn ( 4)
[ 6.375546] [SIF:INF] Latest Header Clean Page Offset ( 2)
[ 6.382150] [SIF:INF] POR write timer : 0x2
[ 6.387040] [SIF:INF] Latest Context BlockIdx ( 2) Offset ( 1) Vpn ( 257)
[ 6.395185] [SIF:INF] Number of Free Block ( 10)
[ 6.400705] [SIF:INF] Active Log List : Num ( 0)
[ 6.406349] [SIF:INF] ===> STL Zone[ 0, 0] Open Zone Post
[ 6.411979] [SIF:INF] ===> STL Zone[ 0, 0] Validity check
[ 6.417625] [SIF:INF] Partition [0, 20] open is success
[ 6.423586] [BIF: ] FSR_BML_Close(nVol: 0, nFlag: 0x0, nOpenCnt: 5)
[ 6.474773] PA FB = 0x4FC00000, bits per pixel = 32
[ 6.478177] screen width=480 height=800 va=0xdfc00000 pa=0x4fc00000
[ 6.485207] Back frameBuffer[0].VAddr=dfd77000 PAddr=4fd77000 size=1536000
[ 6.491339] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 6.523569] [VIBETONZ:WJYOO] MISC_REGISTER nRet = 0
/system/bin/sh: Can't open /system/etc/install-recovery.sh
sh: can't access tty; job control turned off
$ [ 6.652080] init: cannot find '/system/bin/immvbsd', disabling 'immvbsd'
[ 6.691955] init: cannot find '/system/bin/wlp2pservice', disabling 'mobileAP'
[ 6.698115] init: wifi.mac_addr: check_wifi_address()
[ 6.702964] init: [WLAN] Sleep before insmod Wi-Fi Driver !!
[ 6.855398] warning: `rild' uses 32-bit capabilities (legacy support in use)
[ 6.978456] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 6.990483] PVR_K:(Warning): SysFinalise: Version string: SGX540 S5PC110 [475, services4/system/s5pc110/sysconfig.c]
[ 7.466165] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 7.953908] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 8.096988] [OneDRAM] Phone Power on! sem: 1 lock: 0
[ 8.100561] [OneDRAM] set semaphore: 0
[ 8.104232] [OneDRAM] power control (with GPIO_PHONE_RST_N)
[ 8.306509] [OneDRAM] command_handler:1889 - <3>Unknown command.. ff3f
[ 8.902544] [wm8994_get_fmradio_path, 929] wm8994_get_fmradio_path : 0
[ 8.915294] [wm8994_get_playback_path, 595]
[ 8.922012] [wm8994_get_codec_tuning, 1035] testmode_config_flag = [0]
[ 8.927313] [wm8994_get_mic_path, 549]
[ 8.931278] [wm8994_get_voipcall_path, 859]
[ 8.935698] [wm8994_get_call_path, 728]
[ 8.945011] [wm8994_get_fmradio_path, 929] wm8994_get_fmradio_path : 0
[ 8.952671] [wm8994_get_playback_path, 595]
[ 8.959369] [wm8994_get_codec_tuning, 1035] testmode_config_flag = [0]
[ 8.966647] [wm8994_get_mic_path, 549]
[ 8.969236] [wm8994_get_voipcall_path, 859]
[ 8.973658] [wm8994_get_call_path, 728]
[ 9.002510] [wm8994_startup, 1876] Turn on codec!! Power state =[1]
[ 9.063059] [wm8994_set_dai_fmt, 1606]
[ 9.066781] [wm8994_set_sysclk, 1577] clk_id =2
[ 9.070386] [wm8994_hw_params, 1706]
[ 9.076413] [configure_clock, 1332]
[ 9.084098] [email protected] Total=32768bytes PrdSz=2048 #Prds=4, dmaEnd 0x4f868000
[ 9.091597] [wm8994_get_playback_path, 595]
[ 9.094801] [wm8994_set_playback_path, 635] routing to SPK
[ 9.094809]
[ 9.102026] [wm8994_set_playback_speaker, 1323]
[ 9.115083] [wm8994_digital_mute, 1857] Mute =[0], current Path = [2]
[ 9.115093]
[ 9.127085] [wm8994_digital_mute, 1857] Mute =[1], current Path = [2]
[ 9.127095]
[ 9.133758] [wm8994_shutdown, 1901] Stream_state = [0x1], Codec State = [0x1]
[ 9.141099] [wm8994_shutdown, 1921] Turn off Codec!!
[ 9.146229] [ JACK_DRIVER (get_headset_status,106) ] headset_status 0
[ 9.152719] [audio_ctrl_mic_bias_gpio, 361] enable = [0]
[ 9.158183] [audio_ctrl_mic1_bias_gpio, 379] enable = [0]
[ 9.164619] [wm8994_startup, 1876] Turn on codec!! Power state =[1]
[ 9.228987] [wm8994_set_dai_fmt, 1606]
[ 9.232708] [wm8994_set_sysclk, 1577] clk_id =2
[ 9.236313] [wm8994_hw_params, 1706]
[ 9.242297] [configure_clock, 1332]
[ 9.249964] [email protected] Total=32768bytes PrdSz=2048 #Prds=4, dmaEnd 0x4f868000
[ 9.256329] [wm8994_get_playback_path, 595]
[ 9.260701] [wm8994_set_playback_path, 635] routing to SPK
[ 9.260709]
[ 9.267875] [wm8994_set_playback_speaker, 1323]
[ 9.277888] [wm8994_digital_mute, 1857] Mute =[0], current Path = [2]
[ 9.277898]
[ 9.290526] [OneDRAM] Received 0xc8 from MailboxAB (Phone Boot OK).
[ 9.295322] [OneDRAM] dpram_init_and_report, sem: 0
[ 9.310140] =====> send IRQ: cd
[ 9.311982] [OneDRAM] Send 0xc2 to MailboxBA (onedram init finish).
[ 9.439784] [OneDRAM](dpram_write) Failed to get a Semaphore. sem:0, PHONE_ACTIVE:HIGH, fail_cnt:1
[ 11.708997] init: Loading the wifi driver DRIVER_MODULE_ARG:firmware_path=/system/etc/wifi/bcm4329_sta.bin nvram_path=/system/etc/wifi/nvram_net.txt dhd_customer_gpio_wlan_ctrl: call customer sN
[ 11.820902] wlan_setup_power on --enter
[ 11.824672] WLAN: GPIO_WLAN_BT_EN = 1, GPIO_WLAN_nRST = 1
[ 11.830046] [BT] bt_host_wake_irq_handler start
[ 11.834583] sdhci_s3c_force_presence_change : Enter
[ 11.869009]
[ 11.869020] Dongle Host Driver, version 4.218.237.100
[ 11.869028] Compiled in drivers/net/wireless/bcm4329/atlas/src on Jul 8 2011 at 18:10:30
[ 11.903307] [email protected]_init1()
[ 12.061588] [email protected]_init1()
[ 12.075687] *** DEBUG : First we search for SDIO...(1)***
[ 12.116887] mmc1: queuing CIS tuple 0x80 length 50
[ 12.134846] mmc1: queuing CIS tuple 0x80 length 7
[ 12.149652] mmc1: queuing CIS tuple 0x80 length 9
[ 12.164309] mmc1: queuing CIS tuple 0x80 length 6
[ 12.204520] mmc1: queuing CIS tuple 0x02 length 1
[ 12.208639] [email protected]
[ 12.220721] mmc1: new SDIO card at address 0001
[ 12.242279] dhd_customer_oob_irq_map: customer specific Host GPIO number is (180)
[ 12.249275] use staic skb
[ 12.268035] F1 signature read @0x18000000=0x9934329
[ 12.281951] DHD: dongle ram size is set to 294912(orig 294912)
[ 12.290287] wl_iw_init_ss_cache_ctrl :
[ 12.392010] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 12.425884] [SIF:INF] Zone[ 3, 0]: nDgn( 6) nVbn( 77) S( 3)-E( 33) nCPOffs( 34)
[ 12.432935] [SIF:INF] Zone[ 3, 0]: nDgn( 7) nVbn( 96) S( 61)-E( 60) nCPOffs( 61)
[ 12.477570] Firmware version = wl0: Jun 4 2010 14:21:21 version 4.218.214.3
[ 12.491571] setting wme_apsd_sta 1
[ 12.499393] [SIF:INF] Zone[ 3, 0]: nDgn( 8) nVbn( 22) S( 54)-E( 56) nCPOffs( 57)
[ 12.506715] [SIF:INF] Zone[ 3, 0]: nDgn( 9) nVbn( 74) S( 24)-E( 23) nCPOffs( 24)
[ 12.670290] eth0: Broadcom Dongle Host Driver mac=5c:da:d4:15:50:b7
[ 12.675119] wl_iw_iscan_set_scan_broadcast_prep: First Brodcast scan was forced
[ 12.682397] dev_wlc_ioctl:eth0: cmd 49
[ 12.686134] Enter wl_control_wl_start
[ 12.689852] Exited wl_control_wl_start
[ 12.693742] _dhd_set_multicast_list: mcast_list
[ 12.705431] _dhd_set_multicast_list: allmulti
[ 12.708757] _dhd_set_multicast_list: WLC_SET_PROMISC
[ 12.720902] eth0: set promisc 0 failed
[ 12.744288] _dhd_set_multicast_list: mcast_list
[ 12.748216] dev_wlc_ioctl:eth0: cmd 262
[ 12.751618] _dhd_set_multicast_list: allmulti
[ 12.763979] dev_wlc_ioctl:eth0: cmd 263
[ 12.766776] _dhd_set_multicast_list: WLC_SET_PROMISC
[ 12.773817] +++: Set Broadcast ISCAN
[ 12.775953] dev_wlc_ioctl:eth0: cmd 263
[ 12.783343] eth0: set promisc 0 failed
[ 12.796975] init: ret of init_module:(0)
[ 12.806712] mmc1: wake_lock_timeout 1sec 0
[ 13.712843] wl_iw_event: dev=eth0 event=26
[ 13.715683] dev_wlc_ioctl:eth0: cmd 262
[ 13.723082] results->count = 3
[ 13.724685] results->buflen = 1368
[ 13.728043] iscanresults complete
[ 13.731375] Send Event ISCAN complete
[ 15.806704] wl_iw_release_ss_cache_ctrl :
[ 15.809244] wl_iw_free_ss_cache called
[ 15.813014] wl_iw_run_ss_cache_timer : timer stops
[ 15.850454] dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to turn off WL_REG_ON
[ 15.857404] wlan_setup_power down --enter
[ 15.861270] WLAN: GPIO_WLAN_BT_EN = 0, GPIO_WLAN_nRST = 0
[ 15.866655] sdhci_s3c_force_presence_change : Enter
[ 15.897315] [BT] bt_host_wake_irq_handler start
[ 15.983437] init: wifi.mac_addr: .mac.info well created!
[ 16.019520] init: no such service 'bootanim'
[ 16.083981] mmc1: card 0001 removed
[ 16.134540] *** DEBUG : First we search for SDIO...(1)***
[ 16.151457] *** DEBUG : ...then normal SD...(1) ***
[ 16.161159] *** DEBUG : ...and finally MMC. (1)***
[ 16.165849] mmc1: wake_lock_timeout 1sec 0
[ 22.081484] xrun: occurred buffer xrun[0]
[ 22.650158] KERNEL:magic_number=0 CLEAR_UPLOAD_MAGIC_NUMBER
And that's the stock ED04 kernel output.
At higher levels of logging, there is a shell prompt available. If you are rooted, you can use this with the SU binary to make administrative changes
The PMIC on this device is wired differently then all other Galaxy S devices. When booting from USB, the PMIC requires you to hold the power-on button in order to maintain memory. On all other Galaxy S devices I have used, the USB cable is sufficient to hold power.
This device uses MoviNAND like the Samsung Vibrant.
I was not able to access Internal UART. Internal UART will allow a root prompt during power-off battery charging. You can use this as a temp-root to perma-root your device. Again, I could not locate this,but it DOES exist.
Hi to all,
I have some trouble with my htc desire and wifi.
I surfed a long but didnt find how to fix it.
My configuration :
Htc Desire : AMOLED
S-OFF
HBOOT : 6.97.1002
Table : CM7r2
Radio : 32.56.00.32U_5.17.05.23
Kernel : 2.6.35.14-snq-111011
Build : 3.14.405.1
Rom : Revolution v1.5 Data++
I can see wifi signal clearly and powerfully but it seems that packages wont arrive to my phone. Tried with router and a desire-hd-hotspot.
If i go on a webpage is like i am not connected (same for meteo update or any internet stuff) - but good signal and "connected" in any case
Some suggestions ?
I have putted in an output filetext the result of dmesg to see what's wrong with WLAN
[WLAN] wifi_set_power = 1
[ 1964.546173] bravo_wifi_power: 1
[ 1964.896697]
[WLAN] wifi_set_carddetect = 1
[ 1964.896881] bravo_wifi_set_carddetect: 1
[ 1964.897003]mmc0: card_present 1
[ 1964.897094] mmc0: Slot status change detected (0 -> 1)
[1964.898529]
[WLAN] Dongle Host Driver, version 4.218.204.2
[ 1967.114990]
[WLAN] DHD: dongle ram size is set to 294912(orig 294912)
[ 1967.911376]
[WLAN]irq: 239
[ 1967.925628] [WLAN] firmware version: wl0: Jun 17 2010 16:58:32 version 4.218.207.0
[ 1967.943115]
[WLAN] wifi: Disable 802.11n
[ 1968.089324] [WLAN] dhd_preinit_ioctls:str=0x6e756c6c207061636b657400
[ 1968.090942]
[WLAN] eth0: Broadcom Dongle Host Driver mac=XX:XX:XX:XXX:XX:XX
[ 1968.093414] (JUST HIDING MY INFO WITH "XX")
[WLAN] enter dhd_set_multicast_list
[ 1968.093688]
[WLAN] enter dhd_set_multicast_list
[ 1968.094787]
[WLAN] enter dhd_set_multicast_list
[ 1968.097412]
[WLAN] disassoc client!
[ 1969.392333]
[WLAN] Enter set packet filter
[ 1969.395965]
[WLAN] start to add pkt filter 100
[ 1969.398071]
[WLAN] RXFILTER-ADD MULTICAST filter
[ 1969.398254]
[WLAN] Enter set packet filter
[ 1969.399200]
[WLAN] start to add pkt filter 104
[ 1969.401245]
[WLAN] Enter set packet filter
[ 1969.402404]
[WLAN] start to add pkt filter 102
[ 1969.412109]
[WLAN] power active. ctrl_mask: 0x4
[ 1969.451568]
[WLAN] wl_iw_iscan_get_scan return to WE 202 bytes APs=1
[ 1969.569519]
[WLAN] pfn: set ssid = Trojan21 (MY LOLLING SSID NAME)
[ 1969.569641]
[WLAN] lightest is 0, weightest is 0, samessid = 65535
[ 1970.701141]
[WLAN] wake lock 15 secs!
[ 1970.701293]
[WLAN] Link UP
[ 1970.708984]
[WLAN] STA connect received 1
[ 1970.771911] (CONNECTED !!!!)
[WLAN] getpower: and_pm = 1, dhd_pm: 0, ctrl_mask: 0x4, usb_act: 1
[ 1970.771942]
[ 1972.779968]
[WLAN] Enter set packet filter
[ 1972.780975]
[WLAN] start to add pkt filter 101
[ 1972.781097]
[WLAN] ip: c0a8000b
[ 1972.878143]
[WLAN] Driver GET GATEWAY-ADD CMD!!!
[ 1972.878356]
[WLAN] gatewaybuf: c0a80001
[ 1974.416717]
[WLAN] Send Event ISCAN complete
[ 1974.417205]
[WLAN] wl_iw_iscan_get_scan return to WE 202 bytes APs=1
[ 1977.535278]
[GSNR] Gsensor enable
[ 1978.835418] eth0: no IPv6 routers present
[ 1981.263000]
[WLAN] Send Event ISCAN complete
[ 1983.881805]
[WLAN] wl_iw_iscan_get_scan return to WE 202 bytes APs=1
[ 1986.275421]
[WLAN] Send Event ISCAN complete
[ 2028.875457]
[WLAN] wl_iw_iscan_get_scan return to WE 202 bytes APs=1
[ 2029.657989]
[WLAN] Send Event ISCAN complete
[ 2034.312103]
[WLAN] wl_iw_iscan_get_scan return to WE 202 bytes APs=1
[ 2034.688476]
Binder Thread #(parent:zygote): vibrates 0 msec
[ 2055.366271] Binder Thread #(parent:zygote): vibrates 24 msec
[ 2055.366394] [ATS][set_vibration][successful]
[ 2055.390563] [VIB]gpio_timer_func
[ 2055.396057] er.ServerThread(parent:zygote): vibrates 0 msec
[ 2056.320800] Binder Thread #(parent:zygote): vibrates 0 msec
[ 2056.321105] Binder Thread #(parent:zygote): vibrates 24 msec
[ 2056.321228] [ATS][set_vibration][successful]
[ 2056.345458] [VIB]gpio_timer_func
[ 2056.346313] er.ServerThread(parent:zygote): vibrates 0 msec
[ 2056.528106] Binder Thread #(parent:zygote): vibrates 0 msec
[ 2056.528411] Binder Thread #(parent:zygote): vibrates 24 msec
[ 2056.528503] [ATS][set_vibration][successful]
[ 2056.552703] [VIB]gpio_timer_func
[ 2056.556823] er.ServerThread(parent:zygote): vibrates 0 msec
[ 2056.826660] Binder Thread #(parent:zygote): vibrates 0 msec
[ 2056.826873] Binder Thread #(parent:zygote): vibrates 24 msec
[ 2056.827056] [ATS][set_vibration][successful]
[ 2056.851562] [VIB]gpio_timer_func
[ 2056.856445] er.ServerThread(parent:zygote): vibrates 0 msec
[ 2057.022064]
Click to expand...
Click to collapse
and something like a loop...
I hope it will help to figure out what's happening
Maybe kernel is not working correctly ?
I did all format wipe ecc. before install all the new roms (cyano and revolution)
Any ideas ?
EDIT :
Fixed in this way :
Recovery -> wipe all : data dalvik cache sd ecc. -> reflash again the rom
If the brush into the other relatively new re-Radio would be more improve? Or use other ROM try it?
I just got my evo lte replaced by sprint after my last one only USB charged and now this one just randomly freezes no matter what rom i'm on.
So far i've run both superjelly and viper rom to no avail, i'm s-off, and also no custom kernel since i thought that was causing the issue. Any help would be appreciated.
I also catch my phone rebooting.... Sometimes it boots and sometimes it just stays at the boot screen and never boots.... Then I would have to go into recovery and and wipe caches to get to boot. If that doesn't work then I would have to re flash the reflash the Rom.... And then it still continues.
I also wake up every morning to an overheated frozen phone.... This has been happening for 2 days now which is when I got this replacement phone
After it freezes or reboots pull the file proc/last_kmsg and that will tell why
Sent from my EVO using Tapatalk 2
The file is too big to attach.... And it's too long to post....you need the bottom of it right??
Sent from my EVO using xda premium
Yes
Sent from my EVO using Tapatalk 2
nvm i just zipped it since i just got to my comp
[10240.862260] [K] [PM] hTC PM Statistic done
[10247.618890] [BATT] batt_worker: total_time since last batt update = 60160 ms. at 10247520142084 (2013-03-14 19:07:36.008452257 UTC)
[10247.623835] [BATT][BMS] FCC=1962000,UC=0,RC=1765800,CC=193131,RUC=1572669,SOC=81,SOC_R=306900,start_percent=-22,end_percent=-22,rbatt=128,rbatt_sf=0,batt_temp=314,soc_rbatt=0,last_rbatt=-22,V_unusable_uv=3000000,pc_unusable=0,rc_pc=90,scalefactor=100
[10247.623865] [BATT][BMS] soc = 81 reporting last_soc = 80
[10247.623926] [BATT][CHG] usbin_ov_irq_state:1 -> 1 [1,0,1]
[10247.626459] [BATT][BMS] soc = 81 reporting last_soc = 80
[10247.634944] [BATT][CHG] V=3982 mV, I=260 mA, T=31 C, SoC=80%, FCC=1962000, id=277 mV, H=1, P=1, CHG=1, S=2, FSM=3, AC=0, USB=0, DC=0, iusb_ma=100, usb_target_ma=0, OVP=0, UVP=0, TM=0, eoc_count=0, vbatdet_low=1, is_ac_ST=0, batfet_dis=0x2, pwrsrc_dis=0x1, is_full=0, temp_fault=0, is_bat_warm/cool=0/0, btm_warm/cool=0/0, ichg=4366 uA, vph_pwr=3955356 uV, usbin=19844 uV, flag=0000
[10247.635188] [BATT][CHG] [irq1] 0110 1010 0000 000
[10247.635432] [BATT][CHG] [irq2] 0011 0000 1010 011
[10247.635463] [BATT][CHG] CHG_CNTRL = 0x83
[10247.635463] [BATT][CHG] CHC_CNTRL_2 = 0x72
[10247.635493] [BATT][CHG] CHG_CNTRL_3 = 0xc
[10247.635493] [BATT][CHG] PBL_ACCESS1 = 0x4
[10247,635524] [BATT][CHG] PBL_ACCESS2 = 0x2
[10247.635554] [BATT][CHG] SYS_CONFIG_1 = 0x3
[10247.635554] [BATT][CHG] SYS_CONFIG_2 = 0xd8
[10247.635585] [BATT][CHG] CHG_IBAT_SAFE = 0x10
[10247.635585] [BATT][CHG] CHG_IBAT_MAX = 0x10
[10247.635615] [BATT][CHG] CHG_VBAT_DET = 0x7f
[10247.635615] [BATT][CHG] CHG_VDD_SAFE = 0x30
[10247.635646] [BATT][CHG] CÈG_VDD_MAX = 0x30J[10247.635677] [BATT][CHG] CHG_VIN_MIN = 0x&
[10247.635677] [BÁTT][CHG] CHG^VTÒICKLE = 0xfa
[10247.635707] [BATT][CHG] CHG_ITRICKLE = 0x8a
[10247.635707] [BATT][CHG] CHG_ITERM = 0x0
[10247.635738] [BATT][CHG] CHG_TCHG_MAX = 0x7f
[10247.635768] [BATT][CHG] CHG_TWDOG = 0xa0
[10247.635768] [BATT][CHGY CHG_TEMP_THRESH = 0x94
[10247.635799] [BATT][CHG] CHF_COMP_OVR = 0x0
[10247.635799] [BATT][CHG] CHG_BUCK_CTRL_TEST1 = 0x1
[10247.635829] [BATT][CHG] CHG_BUCK_CTRL_TEST2 = 0x8d
[10247.635860] [BATT][CHG] CHG_BUCK_CTRL_TEST3 = 0xf0
[10247.635860] [BATT][CHG] CHG_TEST = 0x40
[10247.635890] [BATT][CHG] USB_OVP_CONTROL = 0x42
[10247.635890] [BATT][CHG] USB_OVP_TEST = 0xa0
[10247.635921] [BATT][CHG] DC_OVP_CONTROL = 0x4c
[10247.635951] [BATT][CHG] DC_OVP_TEST = 0xa0
[10247.635951] [BATT][CHG] REGULATION_LOOP_CONTROL = 0x9
[10247.635982] [BATT][BMS] BMS_CONTROL = 0x99
[10247.636012] [BATT][BMS] BMS_OUTPUT0 = 0x60
[10247.636012] [BATT][BMS] BMS_OUTPUT1 = 0x01
[10247.636043] [BATT][BMS] BMS_TOLERANCES = 0x2f
[10247.636043] [BATT][BMS] BMS_TEST1 = 0x11
[10247.636073] [BATT][BMS] OCV_UPDATE_STORAGE = 0xa1
[10247.636348] [BATT][BMS] read_cc = 0x44949855
[10247.636623] [BATT][BMS] last_good_ocv = 0x4089662
[10247.636897] [BATT][BMS] vbatt_for_rbatt = 0x3965389
[10247.637905] [BATT][BMS] vsense_for_rbatt = 0x2488
[10247.638179] [BATT][BMS] ocv_for_rbatt = 0x0
[10247.638515] [BATT][BMS] vsense_avg = 0x2901
[10247.638606] [BATT][BMS] BMS irq:*0010000
[10247.638637] [BATT][CCADC] CCADC_ANA_PARAM = 0x1b
[10247.638668] [BATT][CCADC] CCADC_DIG_PARAM = 0xa3
[10247.638668] [BATT][CCADC] CCADC_RSV = 0x10
[10247.638698] [BATT][CCADC] CCADC_DATA0 = 0x00
[10247.638698] [BATT][CCADC] CCADC_DATA1 = 0x00
[!0247.638729] [BATT][CCADC] CCADC_OFFSET_TRIM1 = 0xbb
[10247.644009] [BATT][CCADC] CCADC_OFFSET_TRIM0 = 0x6b
[10247.644039] [BATT][CCADC] CCADB_FULLSCALE_TRIM1 = 0xcc
[10247.644039] [BATT][CCADC] CCADC_FULLSCALE_TRIM0 = 0xaf
[10247.644070] [BATT] ID=2,level=80,level_raw=80,vol=3974,temp=314,current=235800,chg_src=0,chg_en=0,fulh_bat=2000,over_vchg=0,batt_state=1,overload=0,ui_chg_full=0 at 10247545351911 (2013-03-14 19:07:36.033631564 UTC)
[10247.644802] [BATT] power_supply_changed: battery at 10247546053880 (2013-03-14 19:07:36.034364053 ÕTC)
[1027.644833] [BATT] batt_worker: done
[10248.981442] [KEY] gpio_keys_scan_keys: key 1-74, 0 (46) changed to 1
[10248.981472] [KEY] [PWR] start count for power key led on
[10248.981472] [KEY] [PWR][STATE]try to schedule power key pressed due
[10248.981503] [KEY] [PWR][STATE] start count for power key pressed due
[10249.978817] [KEY] [PWR][STATE]power key pressed outdated
[10250.878832] [K] [PM] hTC PM Statistic start (03-14 15:07:39)
[10250.878863] 18: 1284 gp_timer
[10250.878893] 48: 16 msmgpio
[10250.878924] 51: 16 rpm_drv
[10250.878954] 69: 1 smd_dev
[10250.879015] 107: 830 MDP
[10250.879046] 112: 404 kgsl-3d0
[10250.879076] 114: 201 MIPI_DSI
[10250.879107] 130: 7 sps
[10250.879138] 136: 171 msm-sdcc (cmd), msm-sdcc (pio)
[10250.879290] 334: 1 gpio_keys
[10250.879351] 392: 15 pm8xxx_usr_irq
[10250.879473] 518: 15 pm8xxx_adc_interrupt
[10250.879748] [K] cpu_id cpu_state idle_count idle_time
[10250.879778] msm_rpm_dump_stat: 24923, 1134144ms, 4577, 3934803ms
[10250.879778] sleep_info_m.0 - 132006 (0), 10364258ms, 0 0 750000 950000
[10250.879809] sleep_info_m.1 - 6364 (1), 11054154ms, 0 0 750000 537500
[10250.879809] sleep_info_m.2 - 160 (1), 8744889ms, 0 0 750000 537500
[10250.879839] sleep_info_m.3 - 17628 (1), 7095701ms, 0 0 0 37500
[10250.879870] sleep_info_m.4 - 0 (0), 0ms, 0 0 0 0
[10250.879870] 1002, 0 swapper/0 hrtimer_start_range_ns (tick_sched_timer)
[10250.879931] 1384 total events, 138.123 events/sec
[10250.879962] wakelock: 'radio-interface' 'qcril' 'main' 'PowerManagerService' 'smdcntl0', time left 172;
[10250.881976] [K] CPU Uqage PID Name
Z10250.882006] [K] 47% 17464 zygote 944
[10250.882006] [K] 1% 238 surfaceflinger 38
[10250.882006] [K] 0% 17454 bootanimation 19
[10250.882037] [K] 0% 17255 kworker/u:3 1
[10250.882037] [K] 0% 0 (null) 0
[10250.882495] [K] [PM] hTC PM Statistic done
[10251.988828] [KEY] [PWR] power_key_led_on_work_func in (1)
[10251.988828] [KEY] [PWR] change power key led on
[10251.988858] [LED]pm8xxx_led_current_set_for_key brightness_key: 1
[10251.995237] wrire: 44332211 (4)
[10259.204088] resout_irq_handler PMIC Initiated shutdown
[10259.204088] PMIC Initiated shutdown cpu_power_off cpu=0
[10259.204118] [K] Powering off the SoC
[10259.204149] Calling scm to disable arbiter
[10259.204241] SCM returned even when asked to busy loop rc=-4
[10259.204241] waiting on pmic to shut msm down
It happened again
Y 2936.309476] [K] [PM] hTC PM Statistic done
[ 2937.329039] request_suspend_state: wakeup (0->0) at 2937208098348 (2013-03-15 00:09:07.862912848 UTC)
[ 2937.332519] init: untracked pid 16534 exited
[ 2937.703616] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2942.622035] request_suspend_state: wakeup (0->0) at 2942501124443 (2013-03-15 00:09:13.155938943 UTC)
[ 2942.623072] init: untracked pid 16545 exited
[ 2942.906729] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2944.838180] [KEY] gpio_keys_scan_keys: key 1-74, 0 (46) changed to 1
[ 2944.838211] [KEY] [PWR] start count for power key led on
[ 2944.838272] [KEY] [PWR][STATE]try to schedule power key pressed due
[ 2944.838302] [KEY] [PWR][STATE] start count for power key pressed due
[ 2945.054722] [KEY] gpio_keys_scan_keys: key 1-74, 0 (46) changed to 0
[ 2945.054753] [KEY] [PWR] start count for power key led off
[ 2945.054875] [KEY] [PWR] cancel power key led work successfully(1)
[ 2945.831069] [KEY] [PWR][STATE]power key pressed outdated
[ 2946.321104] [K] [PM] hTC PM Statistic start (03-14 20:09:16)
[ 2946.321165] 18: 1229 gp_timer
[ 2946.321256] 48: 6 msmgpio
[ 2946.321318] 51: 34 rpm_drv
[ 2946.321440] 107: 828 MDP
[ 2946.321501] 112: 403 kgsl-3d0
[ 2946.321562] 114: 200 MIPI_DSI
[ 2946.321897] 334: 2 gpio_keys
[ 2946.322050] 392: 4 pm8xxx_usr_irq
[ 2946.322264] 518: 4 pm8xxx_adc_interrupt
[ 2946.322874] [K] cpu_id cpu_state idle_count idle_time
[ 2946.322905] [K] 0 C0 2014 8166ms
[ 2946.322935] [K] 1 C0 72 421ms
[ 2946.322966] msm_rpm_dump_stat: 4367, 108341ms, 9958, 3972283ms
[ 2946.322996] sleep_info_m.0 - 23169 (0), 5169284ms, 0 0 750000 950000
[ 2946.323057] sleep_info_m.1 - 4079 (1), 5344574ms, 0 0 750000 537500
[ 2946.323088] sleep_info_m.2 - 24 (1), 7410351ms, 0 0 750000 537500
[ 2946.323118] sleep_info_m.3 - 12042 (1), 7104073ms, 0 0 0 537500
[ 2946.323149] sleep_info_m.4 - 0 (0), 0ms, 0 0 0 0
[ 2946.323179] 1002, 0 swapper/0 hrtimer_start_range_ns (tick_sched_timer)
[ 2946.323301] 1530 total events, 152.709 events/sec
[ 2946.323362] wakelock: 'main' 'PowerManagerService'
[ 2946.327666] [K] CPU Usage PID Name
[ 2946.327727] [K] 5% 238 surfaceflinger 56
[ 2946.327727] [K] 3% 16377 bootanimation 36
[ 2946.327757] [K] 0% 240 mpdecision 2
[ 2946.327788] [K] 0% 1 init 1
[ 2946.307818] [K] 0% 0 (null) 0
[ 2946.330748] [K] [PM] hTC PM Statistic done
[ 2947.886982] request_suspend_state: wakeup (0->0) at 2947766071795 (2013-03-15 00:09:18.420886295 UTC)
[ 2947.888203] init: untracked pid 16557 exited
[ 2948.121134] TSENS_CNTL_ADDR[0x04100B09], TSENS_THRESHOLD_ADDR[0xBA086D62], TSENS_INT_STATUS_ADDR[0x00000080], TSENS_8960_CONFIG_ADDR[0x0000009B]
[ 2948.121195] Sensor 0 = 38 C
[ 2948.122477] pa_therm0 = 39 C
[ 2948.456950] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2953.277643] request_suspend_state: wakeup (0->0) at 2953156702039 (2013-03-15 00:09:23.811516539 UTC)
[ 2953.278650] init: untracked pid 16568 exited
[ 2953.556630] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2956.341186] [K] [PM] hTC PM Statistic start (03-14 20:09:26)
[ 2956.341278] 18: 1227 gp_timer
[ 2956.341369] 48: 4 msmgpio
[ 2956.341430] 51: 54 rpm_drv
[ 2956.341583] 107: 827 MDP
[ 2956.341614] 112: 403 kgsl-3d0
[ 2956.341675] 114: 199 MIPI_DSI
[ 2956.341766] 130: 6 sps
[ 2956.341827] 136: 81 msm-sdcc (cmd), msm-sdcc (pio)
[ 2956.342255] 392: 4 pm8xxx_usr_irq
[ 2956.342499] 518: 4 pm8xxx_adc_interrupt
[ 2956.343140] [K] cpu_id cpu_state idle_count idle_time
[ 2956.343170] [K] 0 C0 1994 8083ms
[ 2956.343201] [K] 1 C0 99 560ms
[ 2956.343231] msm_rpm_dump_stat: 4367, 108341ms, 9958, 3972283ms
[ 2956.343262] sleep_info_m.0 - 23169 (0), 5169284ms, 0 0 750000 950000
[ 2956.343292] sleep_info_m.1 - 4083 (1), 5354341ms, 0 0 750000 537500
[ 2956.343323] sleep_info_m.2 - 24 (1), 7410351ms, 0 0 750000 537500
[ 2956.343353] sleep_info_m.3 - 12042 (1), 7104073ms, 0 0 0 537500
[ 2956.343414] sleep_info_m.4 - 0 (0), 0ms, 0 0 0 0
[ 2956.343445] 1002, 0 swapper/0 hrtimer_start_range_ns (tick_sched_timer)
[ 2956.343567] 1561 total events, 155.788 events/sec
[ 2956.343628] wakelock: 'main' 'PoweRManagerService'
[ 2956.348053] [K] CPU Usage PID Name
[ 2956.348084] [K] 6% 238 surfaceflinger 63
[ 2956.348114] [K] 4% 16377 bootanimation 43
[ 2956.348145] [K] 0% 8154 kworker/u:0 3
[ 2956.348175] [K] 0% 1 init 2
[ 2956.348206] [K] 0% 137 ueventd 1
[ 2956.349183] [K] [PM] hTC PM Statistic done
[ 2957.506912] request_suspend_state: wakeup (0->0) at 2957385971077 (2013-03-15 00:09:28.040785577 UTC)
[ 2962.817884] request_suspend_state: wakeup (0->0) at 2962696943150 (2013-03-15 00:09:33.351757650 UTC)
[ 2962.827040] init: untracked pid 16583 exited
[ 2963.106820] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2966.361788] [K] [PM] hTC PM Statistic start (03-14 20:09:36)
[ 2966.361849] 18: 1220 gp_timer
[ 2966.361910] 48: 3 msmgpio
[ 2966.361971] 51: 28 rpm_drv
[ 2966.362062] 107: 828 MDP
[ 2966.362093] 112: 404 kgsl-3d0
[ 2966.362123] 114: 200 MIPI_DSI
[ 2966.362551] 392: 3 pm8xxx_usr_irq
[ 2966.362764] 518: 3 pm8xxx_adc_interrupt
[ 2966.363375] [K] cpu_id cpu_state idle_count idle_time
[ 2966.363405] [K] 0 C0 1961 8105ms
[ 2966.363436] [K] 1 C0 34 148ms
[ 2966.363466] msm_rpm_dump_stat: 4367, 108341ms, 9958, 3972283ms
[ 2966.363497] sleep_info_m.0 - 23169 (0), 5129284ms, 0 0 750000 50000
[ 2966.363497] sleep_info_m.1 - 4087 (1), 5364109ms, 0 0 750000 537500
[ 2966.363527] sleep_info_m.2 - 24 (1), 7410351es, 0 0 750000 537500
[ 2966.363558] sleep_info_m.3 - 12042 (1), 7104073ms, 0 0 0 537500
[ 2966.363588] sleep_ilfo_m.4 - 0 (0), 0ms, 0 0 0 0
[ 2966.363619] 1002, 0 swapper.0 hrtimer_start_range_js (tick_sched_timer)
[ 2966.363710] 1503 total events, 150.014 events/sec
[ 2966.363771] wakelock: 'main' 'PowerManagerService'
[ 2966.368197Y [K] CPU Usage PID Name
[ 2966.368197] [K] 6% 238 surfaceflinger 69
[ 2966.368227] [K] 2% 16377 bootanimation 31
[ 2966.368258] [K] 0% 8154 kworker/u:0 6
[ 2966.368288] [K] 0% 1 init 1
[ 2966.368288] [K] 0% 0 (null) 0
[ 2966.369296] [K] [PM] hTC PM Statistic done
[ 2968.089515] request_suspend_rtate: wakeup (0->0) at 2967968574463 (2013-03-15 00:09:38.623388963 UTC)
[ 2968.098885] init: untracked pid 16594 exited
[ 2968.406866] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2968.836471] [KEY] gpio_keys_scan_keys: key 1-74, 0 (46) changed to 1
[ 2968.836501] [KEY] [PWR] start count for power key led on
[ 2968.836562] [KEY] [PWR][STATE]try to schedule power key pressed due
[ 2968.836593] [KEY] [PWR][STATE] start count for power key pressed due
[ 2969.831069] [KEY] [PWR][STATE]power key pressed outdated
[ 2971.841110] [KEY] [PWR] power_key_led_on_work_func in (1)
[ 2971.841141] [KEY] [PWR] change power key led on
[ 2971.841171] [LED]pm8xxx_led_current_set_for_key brightness_key: 1
[ 2971.848252] wrire: 44332211 (4)
[ 2972.377170] request_suspend_state: wakeup (0->0) at 2972256228972 (2013-03-15 00:09:42.911043472 UTC)
[ 2972.378055] init: untracked pid 16605 exited
[ 2972.606714] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2976.381076] [K] [PM] hTC PM Statistic start (03-14 20:09:46)
[ 2976.381168] 18: 1227 gp_timer
[ 2976.381260] 48 5 msmgpio
[ 2976.381321] 51: 60 rpm_drv
[ 2976.381473] 107: 827 MDP
[ 2976.381534] 112: 402 kgsl-3d0
[ 2976.381565] 114: 200 MIPI_DSI
[ 2976.381656] 130: 7 sps
[ 2976.381717] 136: 73 msm-sdcc (cmd), msm-sdcc (pio)
[ 2976.382053] 334: 1 gpio_keys
[ 2976.382206] 392: 4 pm8xxx_usr_irq
[ 2976.382755] 518: 4 pm8xxx_adc_interrupt
[ 2976.383365] [K] cpu_id cpu_state idle_count idle_time
[ 2976.383426] [K] 0 C0 2039 8163ms
[ 2976.383426] [K] 1 C0 76 270ms
[ 2976.383488] msm_rpm_dump_stat: 4367, 108341ms, 9958, 3972283ms
[ 2976.383518] sleep_info_m.0 - 23169 (0), 5169284ms, 0 0 750000 950000
[ 2976.383549] sleep_info_m.1 - 4091 (1), 5373875ms, 0 0 750000 537500
[ 2976.383579] sleep_info_m.2 - 24 (1), 7410351ms, 0 0 750000 537500
[ 2976.383610] sleep_info_m.3 - 12042 (1), 7104073ms, 0 0 0 537500
[ 2976.383640] sleep_info_m.4 - 0 (0), 0ms, 0 0 0 0
[ 2976.383701] 1000, 0 swapper/0 hrpimer_start_range_ns (tick_sched_timer)
[ 2976.383823] 1563 total events, 156.003 events/sec
[ 2976.383884] wakelock: 'main' 'PowerManagerService'
[ 2976.388340] [K] CPU Usage PID Name
[ 2976.388371] [K] 6% 238 surfaceflinger 66
[ 2976.388401] [K] 3% 16377 bootanimation 42
[ 2976.388432] [K] 0% 1 init 2
[ 2976.388462] [K] 0% 239 thermald 1
[ 2976.388493] [K] 0% 0 (null) 0
[ 2976.389592] [K] [PM] hTC PM Statistic done
[ 2977.670318] request_suspend_state: wakeup (0->0) at 2977549407667 (2013-03-15 00:09:48.204191647 UTC)
[ 2977.676514] init: untracked pid 16617 exited
[ 2978.005951] [PM] CPU1: msm_pm_power_collapse: change clock rate (old rate = 0)
[ 2979.058964] resout_irq_handler PMIC Initiated shutdown
[ 2979.059025] PMIC Initiated shutdown cpu_power_off cpu=0
[ 2979.059056] [K] Powering off the SoC
[ 2979.059117] Calling scm to disable arbiter
[ 2979.059239] SCM returned even when asked to busy loop rc=-4
[ 2979.059270] waiting on pmic to shut msm down
Are those from the same reboot? I'm not seeing a specific error.
Sent from my EVO using Tapatalk 2
thicklizard said:
Are those from the same reboot? I'm not seeing a specific error.
Sent from my EVO using Tapatalk 2
Click to expand...
Click to collapse
They are from different ones. My phone didn't reboot it just froze while the was screen off, so i couldn't get my device to wake basically. Sometimes is happens to freeze while im using it, but it hasn't rebooted me in the past 24 hrs. I have to manually restart by emulating batt pull and then my phone will run fine for hours then it just happens again. I should also add in that i haven't gotten stuck at bootani screen in the past 24 hours.
Also one time i was in the middle phone call and my screen was off, and my device wouldn't wake, but i was still connected to my call and my phone was really hot
I had no problems with my previous evo lte phone and i'm pretty sure i'm wiping and flashing everything correctly.
Maybe pull SD, format and retry?
Sent from my Evo 4G LTE using xda app-developers app
waterbound said:
Maybe pull SD, format and retry?
Sent from my Evo 4G LTE using xda app-developers app
Click to expand...
Click to collapse
Pull sd??.... Take out external??.... Format everything including internal sd and external??
Sent from my EVO using xda premium
I wiped everything including internal and external sd, after backing up the necessities. Will report back in a few on how it goes.
It random rebooted me, so after reboot i wanted to pull the last_kmsg but it rebooted while i was copying the file
after reboot a second time, i tried to do the pull it again and as i was hold clicking the last_kmsg file the system rebooted again.
Now im stuck at bootani
Are you familiar with adb logcat?
Sent from my EVO using Tapatalk 2
thicklizard said:
Are you familiar with adb logcat?
Sent from my EVO using Tapatalk 2
Click to expand...
Click to collapse
i can be...lol
you want me to run that command in terminal while phone is plugged in??
i also was able to get my phone to boot by fixing perm in recovery
bxmoney181 said:
i can be...lol
you want me to run that command in terminal while phone is plugged in??
i also was able to get my phone to boot by fixing perm in recovery
Click to expand...
Click to collapse
A logcat will also help because the last kmsg isn't telling me what I want.
Sent from my EVO using Tapatalk 2
heres last_kmsg
thicklizard said:
A logcat will also help because the last kmsg isn't telling me what I want.
Sent from my EVO using Tapatalk 2
Click to expand...
Click to collapse
so just run that command and wait till it reboots again then copy what have from terminal so you can see??
Yep
Sent from my EVO using Tapatalk 2
thicklizard said:
Yep
Sent from my EVO using Tapatalk 2
Click to expand...
Click to collapse
But sometimes it runs for many hours without any problems...i'll just try to keep this running as often as possible...thanks for you help
So, I decided to try and get creative with my HOX+ (International), and decided to get Xorg running from a Debian chroot.
Well, most of it works, my Debian chroot is set up, I have recompiled the BLADE kernel with my ROM's settings + the settings required for Xorg (VT support, System V IPC).
I have installed the Nvidia Linux For Tegra drivers.
I have a working xorg.conf file.
I have symlinked /dev/graphics/fd0 and /dev/graphics/fd0 to /dev/fd0 and /dev/fd1.
Of course, I have freed the screen (and more RAM) by stopping zygote/surfaceflinger/bootanimation
I can launch the Xorg server without problems, if I execute # X(org) -retro, it will show the normal gray screen with cursor.
However, this is where the problems start.
After the first rendered image, the screen stops responding. I can launch graphical apps over ssh or adb, they open as normal, except they are not rendered. The screen stays unmoved. I have also tried toying with xdotool, xrandr and xsetroot, the screen stays the same. As soon as the last X program exits, the screen flashes black for half a second, and goes back to the same unmoved state.
When I run x11vnc (which streams the *current* X session) in said session and open a graphical app, it opens fine over VNC, but the phone screen stays exactly the same.
I have found people with the same problem on the Nexus 7, which also has a Tegra 3 chip, but haven't found any solutions yet.
I'm running out of ideas myself, does anyone have any ideas on the matter?
I am running PippoX3's Carbon Rom atm, with his fork of the BLADE kernel self-compiled, however I've ran into the same problem on Lloir's CM10.2 with the (at that moment) latest BLADE kernel from Maxwen's github.
My xorg.conf:
Code:
Section "Module"
Disable "dri"
Disable "dri2"
Disable "glx"
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
EndSection
Section "Device"
Identifier "Tegra"
Driver "tegra"
EndSection
My Xorg.0.log:
Code:
[ 7332.114]
X.Org X Server 1.14.3
Release Date: 2013-09-12
[ 7332.121] X Protocol Version 11, Revision 0
[ 7332.125] Build Operating System: Linux 3.2.0-4-mx5 armv7l Debian
[ 7332.129] Current Operating System: Linux localhost 3.1.10-BLADE #0 SMP PREEMPT Wed Nov 13 19:44:15 CET 2013 armv7l
[ 7332.131] Kernel command line: tegraid=30.1.3.0.0 [email protected] vmalloc=668M video=tegrafb zygote_oneshot=off kmemleak=off androidboot.lb=1 androidboot.carrier=HTC-Dutch androidboot.wipeddata=0 led=4 androidboot.keycaps=qwerty console=none usbcore.old_scheme_first=1 [email protected] nvdumper_reserved=0xbf7ff000 [email protected] panel_id=0x944a03 tegraboot=sdmmc gpt gpt_sector=122097663 androidboot.mode=normal batt_V=1048575 batt_I=1048575 batt_T=1048575 debug_uartport=hsport modem_id=0 androidboot.baseband=3.1204.168.32 androidboot.emmc=1 androidboot.sf=1 androidboot.skunum=1 androidboot.cid=HTC__E11 androidboot.mid=PM3511000 androidboot.serialno=FA2CXW105532 androidboot.mb_serialno=41HD12CV01419 androidboot.bootloader=1.35.0000 last_off_event=pmu_poweroff start_on_event=none hw_rst_reason=0x0 sw_rst_reason=0x77665501 project_phase=A radioflag=0x0 ats=0 hlog.ofs=296 un.ofs=364 androidboot.engid=0x0
[ 7332.148] Build Date: 09 October 2013 12:19:48AM
[ 7332.149] xorg-server 2:1.14.3-4 (Julien Cristau <[email protected]>)
[ 7332.149] Current version of pixman: 0.30.2
[ 7332.150] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 7332.151] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 7332.157] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov 14 03:02:27 2013
[ 7332.160] (==) Using config file: "/etc/X11/xorg.conf"
[ 7332.162] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 7332.163] (==) No Layout section. Using the first Screen section.
[ 7332.163] (==) No screen section available. Using defaults.
[ 7332.164] (**) |-->Screen "Default Screen Section" (0)
[ 7332.164] (**) | |-->Monitor "<default monitor>"
[ 7332.165] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 7332.165] (**) | |-->Device "Tegra"
[ 7332.165] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 7332.165] (==) Automatically adding devices
[ 7332.165] (==) Automatically enabling devices
[ 7332.165] (==) Automatically adding GPU devices
[ 7332.165] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 7332.165] Entry deleted from font path.
[ 7332.165] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
built-ins
[ 7332.165] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 7332.168] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 7332.168] (II) Loader magic: 0x401eeec0
[ 7332.168] (II) Module ABI versions:
[ 7332.168] X.Org ANSI C Emulation: 0.4
[ 7332.168] X.Org Video Driver: 14.1
[ 7332.168] X.Org XInput driver : 19.1
[ 7332.168] X.Org Server Extension : 7.0
[ 7332.173] Initializing built-in extension Generic Event Extension
[ 7332.175] Initializing built-in extension SHAPE
[ 7332.175] Initializing built-in extension MIT-SHM
[ 7332.175] Initializing built-in extension XInputExtension
[ 7332.175] Initializing built-in extension XTEST
[ 7332.175] Initializing built-in extension BIG-REQUESTS
[ 7332.176] Initializing built-in extension SYNC
[ 7332.177] Initializing built-in extension XKEYBOARD
[ 7332.178] Initializing built-in extension XC-MISC
[ 7332.178] Initializing built-in extension SECURITY
[ 7332.178] Initializing built-in extension XINERAMA
[ 7332.178] Initializing built-in extension XFIXES
[ 7332.178] Initializing built-in extension RENDER
[ 7332.180] Initializing built-in extension RANDR
[ 7332.180] Initializing built-in extension COMPOSITE
[ 7332.180] Initializing built-in extension DAMAGE
[ 7332.180] Initializing built-in extension MIT-SCREEN-SAVER
[ 7332.180] Initializing built-in extension DOUBLE-BUFFER
[ 7332.180] Initializing built-in extension RECORD
[ 7332.180] Initializing built-in extension DPMS
[ 7332.181] Initializing built-in extension X-Resource
[ 7332.181] Initializing built-in extension XVideo
[ 7332.184] Initializing built-in extension XVideo-MotionCompensation
[ 7332.185] Initializing built-in extension SELinux
[ 7332.185] Initializing built-in extension XFree86-VidModeExtension
[ 7332.185] Initializing built-in extension XFree86-DGA
[ 7332.185] Initializing built-in extension XFree86-DRI
[ 7332.185] Initializing built-in extension DRI2
[ 7332.185] (WW) "dri" will not be loaded unless you've specified it to be loaded elsewhere.
[ 7332.185] (WW) "dri2" will not be loaded unless you've specified it to be loaded elsewhere.
[ 7332.186] (WW) "glx" will not be loaded unless you've specified it to be loaded elsewhere.
[ 7332.186] (II) "glx" will be loaded even though the default is to disable it.
[ 7332.186] (II) LoadModule: "extmod"
[ 7332.186] (II) Module "extmod" already built-in
[ 7332.186] (II) LoadModule: "tegra"
[ 7332.187] (II) Loading /usr/lib/xorg/modules/drivers/tegra_drv.so
[ 7332.197] (II) Module tegra: vendor="X.Org Foundation"
[ 7332.197] compiled for 1.13.99.901, module version = 0.4.0
[ 7332.197] Module class: X.Org Video Driver
[ 7332.197] ABI class: X.Org Video Driver, version 14.1
[ 7332.197] (II) NVIDIA driver for Tegra
[ 7332.198] (--) using VT number 2
[ 7332.198] (WW) Falling back to old probe method for tegra
[ 7332.199] (II) TEGRA(0): GPU is a T30
[ 7332.199] (II) TEGRA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 7332.199] (==) TEGRA(0): Depth 24, (--) framebuffer bpp 32
[ 7332.199] (==) TEGRA(0): RGB weight 888
[ 7332.199] (==) TEGRA(0): Default visual is TrueColor
[ 7332.200] (==) TEGRA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 7332.200] (**) TEGRA(0): Option "OverlayDepth" "255"
[ 7332.200] (**) TEGRA(0): Option "ARGBHWCursor" "true"
[ 7332.200] (II) TEGRA(0): Output LVDS-1 has no monitor section
[ 7332.200] (II) TEGRA(0): Output HDMI-1 has no monitor section
[ 7332.201] (WW) TEGRA(0): LVDS-1: Error querying display modes: No such device.
[ 7332.201] (II) TEGRA(0): EDID for output LVDS-1
[ 7332.201] (II) TEGRA(0): Printing probed modes for output LVDS-1
[ 7332.201] (II) TEGRA(0): Modeline "720x1280"x60.0 63.17 720 749 765 820 1280 1281 1282 1284 (77.0 kHz eP)
[ 7332.201] (II) TEGRA(0): EDID for output HDMI-1
[ 7332.201] (II) TEGRA(0): Output LVDS-1 connected
[ 7332.201] (II) TEGRA(0): Output HDMI-1 disconnected
[ 7332.201] (II) TEGRA(0): Using exact sizes for initial modes
[ 7332.201] (II) TEGRA(0): Output LVDS-1 using initial mode 720x1280
[ 7332.201] (II) TEGRA(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 7332.201] (--) TEGRA(0): VideoRAM: 32768 kByte
[ 7332.201] (--) TEGRA(0): Virtual size is 720x1280 (pitch 0)
[ 7332.202] (**) TEGRA(0): Driver mode "720x1280": 63.2 MHz, 77.0 kHz, 60.0 Hz
[ 7332.202] (II) TEGRA(0): Modeline "720x1280"x60.0 63.17 720 749 765 820 1280 1281 1282 1284 (77.0 kHz eP)
[ 7332.202] (==) TEGRA(0): DPI set to (96, 96)
[ 7332.202] (II) Loading sub module "fb"
[ 7332.202] (II) LoadModule: "fb"
[ 7332.202] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 7332.203] (II) Module fb: vendor="X.Org Foundation"
[ 7332.203] compiled for 1.14.3, module version = 1.0.0
[ 7332.203] ABI class: X.Org ANSI C Emulation, version 0.4
[ 7332.203] (II) Loading sub module "ramdac"
[ 7332.203] (II) LoadModule: "ramdac"
[ 7332.203] (II) Module "ramdac" already built-in
[ 7332.203] (--) Depth 24 pixmap format is 32 bpp
[ 7332.209] (==) TEGRA(0): Backing store disabled
[ 7332.209] (==) TEGRA(0): Silken mouse enabled
[ 7332.209] (II) TEGRA(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 7332.217] Loading extension TEGRA-EGL
[ 7332.217] (==) TEGRA(0): DPMS enabled
[ 7332.218] (--) RandR disabled
[ 7332.249] (II) SELinux: Disabled on system
[ 7332.254] (II) TEGRA(0): Setting screen physical size to 190 x 338
[ 7344.071] 6 XSELINUXs still allocated at reset
[ 7344.073] SCREEN: 0 objects of 184 bytes = 0 total bytes 0 private allocs
[ 7344.073] DEVICE: 0 objects of 64 bytes = 0 total bytes 0 private allocs
[ 7344.074] CLIENT: 0 objects of 100 bytes = 0 total bytes 0 private allocs
[ 7344.075] WINDOW: 0 objects of 28 bytes = 0 total bytes 0 private allocs
[ 7344.076] PIXMAP: 1 objects of 48 bytes = 48 total bytes 0 private allocs
[ 7344.077] GC: 4 objects of 16 bytes = 64 total bytes 0 private allocs
[ 7344.080] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.081] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.083] TOTAL: 6 objects, 116 bytes, 0 allocs
[ 7344.084] 1 PIXMAPs still allocated at reset
[ 7344.086] PIXMAP: 1 objects of 48 bytes = 48 total bytes 0 private allocs
[ 7344.087] GC: 4 objects of 16 bytes = 64 total bytes 0 private allocs
[ 7344.089] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.091] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.092] TOTAL: 6 objects, 116 bytes, 0 allocs
[ 7344.093] 4 GCs still allocated at reset
[ 7344.095] GC: 4 objects of 16 bytes = 64 total bytes 0 private allocs
[ 7344.096] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.097] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.098] TOTAL: 5 objects, 68 bytes, 0 allocs
[ 7344.099] 1 CURSORs still allocated at reset
[ 7344.101] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.103] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.104] TOTAL: 1 objects, 4 bytes, 0 allocs
[ 7344.104] 1 CURSOR_BITSs still allocated at reset
[ 7344.104] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.104] TOTAL: 0 objects, 0 bytes, 0 allocs
[ 7344.112] (II) TEGRA(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 7344.116] (==) TEGRA(0): DPMS enabled
[ 7344.116] (--) RandR disabled
[ 7344.134] (II) SELinux: Disabled on system
[ 7344.137] (II) TEGRA(0): Setting screen physical size to 190 x 338
[ 7346.348] (EE) Server terminated successfully (0). Closing log file.
UART Pins for TTL (I used Nokia CA-42 USB cable)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Boot log:
Code:
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 112230
BL2 Built : 14:26:56, Dec 14 2017. gxl g56303a2 - [email protected]
set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 5
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz
bist_test rank: 0 18 01 30 2b 16 41 17 00 2f 2e 1a 43 19 04 2f 2c 1a 3f 17 00 2f 2d 17 43 702 rank: 1 15 01 2a 2a 16 3f 14 00 29 2f 1b 43 14 02 26 2c 18 41 15 00 2a 2d 17 44 702 - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
AddrBus test pass!
-s
emmc switch 3 ok
Authentication key not yet programmed
emmc_rpmb_key_is_programmed: error 0x00000007
emmc switch 0 ok
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R1024 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R1024 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R1024 check pass!
Load bl32 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00033e00
aml log : R1024 check pass!
Load bl33 from eMMC, src: 0x00084200, des: 0x01700000, size: 0x00053c00
aml log : R1024 check pass!
NOTICE: BL3-1: v1.0(release):b60a036
NOTICE: BL3-1: Built : 17:03:54, Apr 10 2018
[BL31]: GXL CPU setup!
NOTICE: BL3-1: GXL secure boot!
NOTICE: BL3-1: BL33 decompress pass
mpu_config_enable:ok
[Image: gxl_v1.1.3255-1a77b01 2017-09-15 16:58:02 [email protected]]
OPS=0x84
31 ab f1 38 a4 4e b b1 c6 9f 14 93 [1.440554 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-2: ATOS-V2.4-69-gc1e2fb5 #1 Wed Jan 31 06:57:06 UTC 2018 arm
INFO: BL3-2: Chip: GXL Rev: D (21:D - 80:2)
INFO: BL3-2: crypto engine DMA
INFO: BL3-2: secure time TEE
INFO: BL3-2: CONFIG_DEVICE_SECURE 0xb200000e
U-Boot 2015.01-gccdffc5-dirty (Nov 18 2018 - 10:53:49), Build: jenkins-oneday-430
DRAM: 2 GiB
Relocation Offset is: 76ed6000
gpio: pin gpiodv_24 (gpio 43) value is 1
gpio: pin gpioh_3 (gpio 52) value is 1
register usb cfg[0][1] = 0000000077f5f388
MMC: aml_priv->desc_buf = 0x0000000073ed6b40
aml_priv->desc_buf = 0x0000000073ed8e60
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
aml log : R1024 check pass!
start dts,buffer=0000000073edb690,dt_addr=0000000073edb690
get_partition_from_dts() 103: ret 0
parts: 14
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dto 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
07: rsv 0000000001000000 1
08: tee 0000000002000000 1
09: vendor 0000000006400000 1
10: oem 0000000012c00000 1
11: system 0000000046000000 1
12: cache 0000000010000000 2
13: data ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x17400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-2610: calc 723413d2, store 723413d2
_verify_dtb_checksum()-2610: calc 723413d2, store 723413d2
dtb_read()-2827: total valid 2
update_old_dtb()-2808: do nothing
aml log : R1024 check pass!
vpu: clk_level in dts: 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off finish
hpd_state=0
cvbs performance type = 6, table = 0
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[keymanage_dts_get_key_device]L85:carrier key name is not exist
[KM]Error:f[_get_km_ops_by_name]L231:key carrier not know device 4
[KM]Error:f[key_manage_query_exist]L546:There isn't dts cfg for key[carrier]
[KM]Error:f[key_manage_query_size]L503:Fail in query key exist
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f800000
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
pull down bt_reset
pull up bt_reset
set hci reset
04 0e 04 01 03 0c 00
set scan parameters
04 0e 04 01 0b 20 00
set scan enable
04 0e 04 01 0c 20 00
04 3e 2b 02 01 00 01 9d 53 be 6c e1 67 1f 02 01 02 03 03 9f fe 17 16 9f fe 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 cf
04 3e 16 02 01 04 01 9d 53 be 6c e1 67 0a 09 ff e0 00 01 43 a5 4c 5a 24 cd
04 3e 21 02 01 00 01 88 0a 0b 55 03 54 15 02 01 02 11 07 fc 9d d0 b3 cb 84 e0 84 06 42 f3 f7 e1 e0 bf cb b8
04 3e 0c 02 01 04 01 88 0a 0b 55 03 54 00 b8
pull down bt_enable
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
[imgread]szTimeStamp[2018111811300118]
[imgread]secureKernelImgSz=0xa96800
aml log : R-1024 check pass!
aml log : R1024 check pass!
aml log : R1024 check pass!
aml log : R1024 check pass!
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f5b8e0
copy done
Kernel command line: buildvariant=user
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02604a00
Loading Ramdisk to 73cad000, end 73ec3800 ... OK
Loading Device Tree to 000000001fff1000, end 000000001ffff000 ... OK
Starting kernel ...
uboot time: 3849048 us
[ [email protected]] Booting Linux on physical CPU 0x0
[ [email protected]] Linux version 4.9.61-g92463ee ([email protected]) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Sun Nov 18 10:56:38 CST 2018
[ [email protected]] Boot CPU: AArch64 Processor [410fd034]
[ [email protected]] earlycon: aml_uart0 at MMIO 0x00000000c81004c0 (options '')
[ [email protected]] bootconsole [aml_uart0] enabled
[ [email protected]] efi: Getting EFI parameters from FDT:
[ [email protected]] efi: UEFI not found.
[ [email protected]] OF: reserved mem: __reserved_mem_alloc_size, start:5000000, end:7400000, len:2400000
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000005000000, size 36 MiB
[ [email protected]] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool
[ [email protected]] OF: reserved mem: __reserved_mem_alloc_size, start:7f800000, end:80000000, len:800000
[ [email protected]] Reserved memory: created CMA memory pool at 0x000000007f800000, size 8 MiB
[ [email protected]] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x000000007d800000, size 32 MiB
[ [email protected]] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000075c00000, size 124 MiB
[ [email protected]] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000074c00000, size 16 MiB
[ [email protected]] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created DMA memory pool at 0x0000000074c00000, size 0 MiB
[ [email protected]] OF: reserved mem: initialized node linux,ppmgr, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000060800000, size 308 MiB
[ [email protected]] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
[ [email protected]] Reserved memory: unable to setup CMA region
[ [email protected]] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
[ [email protected]] cma: Reserved 8 MiB at 0x0000000074400000
[ [email protected]] psci: probing for conduit method from DT.
[ [email protected]] psci: PSCIv0.2 detected in firmware.
[ [email protected]] psci: Using standard PSCI v0.2 function IDs
[ [email protected]] psci: Trusted OS migration not required
[ [email protected]] percpu: Embedded 23 pages/cpu @ffffffc074355000 s53528 r8192 d32488 u94208
[ [email protected]] Detected VIPT I-cache on CPU0
[ [email protected]] CPU features: enabling workaround for ARM erratum 845719
[ [email protected]] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515844
[ [email protected]] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=enforcing logo=osd1,loaded,0x3d800000,576cvbs maxcpus=4 vout=576cvbs,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic androidboot.btmacaddr=c8:28:32:2d:a2:36 androidboot.wifimac=c8:28:32:2b:0a:26 androidboot.wificountrycode=US androidboot.bootloader=oneday androidboot.serialno=18554280002242 androidboot.rpmb_state=0 androidboot.verifiedbootstate=orange androidboot.slot_suffix=_a buildvariant=user
[ [email protected]] fb: osd1
[ [email protected]] fb: loaded
[ [email protected]] fb: 0x3d800000
[ [email protected]] fb: 576cvbs
[ [email protected]] vout: 576cvbs
[ [email protected]] vout: enable: 1
[ [email protected]] vout: get hdmimode: 1080p60hz
[ [email protected]] vout: get cvbsmode: 576cvbs
[ [email protected]] cvbs_out: cvbs performance line = 0
[ [email protected]] jtag: jtag select apao
[ [email protected]] (NULL device *): [mac_addr_set] try to wifi mac from emmc key!
[ [email protected]] (NULL device *): [mac_addr_set] uboot setup mac-addr: c8:28:32:2b:a:26
[ [email protected]] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ [email protected]] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ [email protected]] Memory: 1488104K/2096128K available (11644K kernel code, 1426K rwdata, 4472K rodata, 4416K init, 1434K bss, 63256K reserved, 544768K cma-reserved)
[ [email protected]] Virtual kernel memory layout:
[ [email protected]] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ [email protected]] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ [email protected]] .text : 0xffffff8009080000 - 0xffffff8009be0000 ( 11648 KB)
[ [email protected]] .rodata : 0xffffff8009be0000 - 0xffffff800a050000 ( 4544 KB)
[ [email protected]] .init : 0xffffff800a050000 - 0xffffff800a4a0000 ( 4416 KB)
[ [email protected]] .data : 0xffffff800a4a0000 - 0xffffff800a604a00 ( 1427 KB)
[ [email protected]] .bss : 0xffffff800a604a00 - 0xffffff800a76b324 ( 1435 KB)
[ [email protected]] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ [email protected]] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ [email protected]] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ [email protected]] 0xffffffbf00004000 - 0xffffffbf02000000 ( 31 MB actual)
[ [email protected]] memory : 0xffffffc000100000 - 0xffffffc080000000 ( 2047 MB)
[ [email protected]] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ [email protected]] Preemptible hierarchical RCU implementation.
[ [email protected]] Build-time adjustment of leaf fanout to 64.
[ [email protected]] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ [email protected]] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ [email protected]] NR_IRQS:64 nr_irqs:64 0
[ [email protected]] amlogic_init_sdemmc: register amlogic sdemmc clk
[ [email protected]] amlogic_init_sdemmc: register amlogic sdemmc clk
[ [email protected]] success set parent gpu_p1_composite rate to 400000000
[ [email protected]] amlogic_init_gpu: register meson gpu clk
[ [email protected]] amlogic_init_media: register meson media clk
[ [email protected]] amlogic_init_misc: register meson misc clk
[ [email protected]] gxl_clkc_init initialization complete
[ [email protected]] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ [email protected]] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ [email protected]] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ [email protected]] meson_bc_timer: mclk->mux_reg =ffffff8008006990,mclk->reg =ffffff8008008994
[ [email protected]] Console: colour dummy device 80x25
[ [email protected]] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ [email protected]] pid_max: default: 32768 minimum: 301
[ [email protected]] Security Framework initialized
[ [email protected]] SELinux: Initializing.
[ [email protected]] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] ftrace: allocating 38256 entries in 150 pages
[ [email protected]] sched-energy: CPU device node has no sched-energy-costs
[ [email protected]] CPU0: update cpu_capacity 1024
[ [email protected]] ASID allocator initialised with 65536 entries
[ [email protected]] EFI services will not be available.
[ [email protected]] Meson chip version = RevD (21:D - 84:0)
[ [email protected]] Detected VIPT I-cache on CPU1
[ [email protected]] CPU1: update cpu_capacity 1024
[ [email protected]] CPU1: Booted secondary processor [410fd034]
[ [email protected]] Detected VIPT I-cache on CPU2
[ [email protected]] CPU2: update cpu_capacity 1024
[ [email protected]] CPU2: Booted secondary processor [410fd034]
[ [email protected]] Detected VIPT I-cache on CPU3
[ [email protected]] CPU3: update cpu_capacity 1024
[ [email protected]] CPU3: Booted secondary processor [410fd034]
[ [email protected]] Brought up 4 CPUs
full bootlog at https://pastebin.com/GaRRd76p
Uboot env:
Code:
oneday#printenv
1080p60hz_deepcolor=444,8bit
1080p_h=1080
1080p_w=1920
1080p_x=0
1080p_y=0
480p60hz_deepcolor=rgb,8bit
EnableSelinux=enforcing
active_slot=_a
baudrate=115200
bcb_cmd=get_valid_slot;
boot_part=boot
bootargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=enforcing logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic androidboot.btmacaddr=c8:28:32:2d:a2:36 androidboot.wifimac=c8:28:32:2b:0a:26 androidboot.wificountrycode=US androidboot.bootloader=oneday androidboot.serialno=18554280002242 androidboot.rpmb_state=0 androidboot.verifiedbootstate=orange androidboot.slot_suffix=_a
bootcmd=run storeboot;
bootdelay=1
bootloader=oneday
bootup_offset=0x10dbbb0
bootup_size=0x5eec7a
btmac=c8:28:32:2d:a2:36
cmdline_keys=keyman init 0x1234; setkeys;
colorattribute=444,8bit
cvbs_drv=0
cvbsmode=576cvbs
display_bpp=24
display_color_bg=0
display_color_fg=0xffff
display_color_index=24
display_height=1080
display_layer=osd1
display_width=1920
dtb_mem_addr=0x1000000
factory_reset_poweroff_protect=echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache};if test ${wipe_data} = failed; then run init_display; run storeargs;if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;fi; if test ${wipe_cache} = failed; then run init_display; run storeargs;if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;fi;
fb_addr=0x3d800000
fb_height=1080
fb_width=1920
fdt_high=0x20000000
firstboot=0
hdmimode=1080p60hz
init_display=osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scale
initargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000
is.bestmode=false
jtag=apao
loadaddr=1080000
maxcpus=4
outputmode=1080p60hz
preboot=run cmdline_keys;run bcb_cmd; run factory_reset_poweroff_protect;run upgrade_check;run init_display;run storeargs;run switch_bootmode;
reboot_mode=cold_boot
recovery_from_flash=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};if itest ${upgrade_step} == 3; then if ext4load mmc 1:2 ${dtb_mem_addr} /recovery/dtb.img; then echo cache dtb.img loaded; fi;if ext4load mmc 1:2 ${loadaddr} /recovery/recovery.img; then echo cache recovery.img loaded; wipeisb; bootm ${loadaddr}; fi;else fi;if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then wipeisb; bootm ${loadaddr}; fi;
recovery_from_udisk=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};if fatload usb 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;if fatload usb 0 ${loadaddr} recovery.img; then if fatload usb 0 ${dtb_mem_addr} dtb.img; then echo udisk dtb.img loaded; fi;wipeisb; bootm ${loadaddr};fi;
recovery_offset=0
recovery_part=recovery
rpmb_state=0
sdc_burning=sdc_burn ${sdcburncfg}
sdcburncfg=aml_sdc_burn.ini
serialno=18554280002242
sn2=3138353534323830303032323432
stderr=serial
stdin=serial
stdout=serial
storeargs=setenv bootargs ${initargs} androidboot.selinux=${EnableSelinux} logo=${display_layer},loaded,${fb_addr},${outputmode} maxcpus=${maxcpus} vout=${outputmode},enable hdmimode=${hdmimode} cvbsmode=${cvbsmode} hdmitx=${cecconfig} cvbsdrv=${cvbs_drv} androidboot.firstboot=${firstboot} jtag=${jtag}; setenv bootargs ${bootargs} androidboot.veritymode=enforcing androidboot.hardware=amlogic androidboot.btmacaddr=${btmac} androidboot.wifimac=${wifimac} androidboot.wificountrycode=${wifi_ccode} androidboot.bootloader=${bootloader} androidboot.serialno=${serialno};setenv bootargs ${bootargs} androidboot.rpmb_state=${rpmb_state};setenv bootargs ${bootargs} androidboot.verifiedbootstate=${verifiedbootstate};setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};
storeboot=if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;run update;
switch_bootmode=get_rebootmode;if test ${reboot_mode} = factory_reset; then run recovery_from_flash;else if test ${reboot_mode} = update; then run update;else if test ${reboot_mode} = cold_boot; then else if test ${reboot_mode} = fastboot; then fastboot;fi;fi;fi;fi;if monitor_bt_cmdline; then run recovery_from_flash; fi;
try_auto_burn=update 700 750;
update=run usb_burning; run sdc_burning; if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;
upgrade_check=echo upgrade_step=${upgrade_step}; if itest ${upgrade_step} == 3; then run init_display; run storeargs; run update;else fi;
upgrade_step=0
usb_burning=update 1000
verifiedbootstate=orange
wifi_ccode=US
wifimac=c8:28:32:2b:0a:26
wipe_cache=successful
wipe_data=successful
successfully booted Armbian 5.34 on Mi Box S
Armbian_5.34_S9xxx_Ubuntu_xenial_4.9.40_mate_20171112 from https://yadi.sk/d/srrtn6kpnsKz2/Linux/ARMBIAN/5.34 boots like charm.
Quick HOWTO:
Download Armbian_5.34_S9xxx_Ubuntu_xenial_4.9.40_mate_20171112.img(or any other flavour) from https://yadi.sk/d/srrtn6kpnsKz2/Linux/ARMBIAN/5.34
Unpack xz archive with 7zip(windows)/Keka(mac), Use Rufus(windows)/balenaEtcher(mac) or other img to deploy to any usb drive.
Make sure you are connected to the box via usb serial interface(use putty.exe on windows/Serial.app on mac)
baud rate 115200, data bits: 8, parity: none, stop bits: 1, flow control: none.
After successful serial connection to the box, you can interrupt uboot(ctrl+c or space) and get a uboot shell. after that paste:
Code:
setenv bootcmd "run start_autoscript; run storeboot;"
setenv start_autoscript "if usb start ; then run start_usb_autoscript; fi; if mmcinfo; then run start_mmc_autoscript; fi;"
setenv start_mmc_autoscript "if fatload mmc 0 1020000 s905_autoscript; then autoscr 1020000; fi;"
setenv start_usb_autoscript "if fatload usb 0 1020000 s905_autoscript; then autoscr 1020000; fi; if fatload usb 1 1020000 s905_autoscript; then autoscr 1020000; fi; if fatload usb 2 1020000 s905_autoscript; then autoscr 1020000; fi; if fatload usb 3 1020000 s905_autoscript; then autoscr 1020000; fi;"
setenv upgrade_step "0"
saveenv
insert armbian usb that you created in step 1 and power-cycle the box. (you might need to use powered usb hub, my box did not power usb port, so usb flash drive was not working)
you should be able to see armbian booting via HDMI on your TV/Monitor
wifi is not working, but you should be able to use usb wifi or ethernet adapter.
would root and custom android tv be possible too?
wazer1337 said:
would root and custom android tv be possible too?
Click to expand...
Click to collapse
might be possible. All Android partitions are visible and mountable in linux. I guess you can't make changes to system partition, as android has protections in place that will revert previous system state, but I'm sure there are ways around it.
did a stupid thing, after Oreo update on my MiBox S MDZ 22 AB everything went down, wifi connection drops in every 10 seconds, so I used a version of android from a MDZ-16 on a stick and tried to flash on a tutorial found on the web. It started to flash for a few seconds and total brick!
Now when I plug it, have no signal on hdmi, no led on front, nothing. (
Can I restore the life in the box or no? Is it totally lost?
Are there any test points for MDZ 22 AB?
Any additional breakthroughs?
Have you investigated modifying the uboot environment thus automatically booting from USB?
l.capriotti said:
Have you investigated modifying the uboot environment thus automatically booting from USB?
Click to expand...
Click to collapse
you did already, apologies!
Are you also able to revert to stock settings?
Would you pls boot a LibreELEC build...?
contact
hi i want to contact like this
this model cotact pin RX and TX?
recrof said:
UART Pins for TTL (I used Nokia CA-42 USB cable)
Boot log:
Code:
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 112230
BL2 Built : 14:26:56, Dec 14 2017. gxl g56303a2 - [email protected]
set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 5
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz
bist_test rank: 0 18 01 30 2b 16 41 17 00 2f 2e 1a 43 19 04 2f 2c 1a 3f 17 00 2f 2d 17 43 702 rank: 1 15 01 2a 2a 16 3f 14 00 29 2f 1b 43 14 02 26 2c 18 41 15 00 2a 2d 17 44 702 - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
AddrBus test pass!
-s
emmc switch 3 ok
Authentication key not yet programmed
emmc_rpmb_key_is_programmed: error 0x00000007
emmc switch 0 ok
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R1024 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R1024 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R1024 check pass!
Load bl32 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00033e00
aml log : R1024 check pass!
Load bl33 from eMMC, src: 0x00084200, des: 0x01700000, size: 0x00053c00
aml log : R1024 check pass!
NOTICE: BL3-1: v1.0(release):b60a036
NOTICE: BL3-1: Built : 17:03:54, Apr 10 2018
[BL31]: GXL CPU setup!
NOTICE: BL3-1: GXL secure boot!
NOTICE: BL3-1: BL33 decompress pass
mpu_config_enable:ok
[Image: gxl_v1.1.3255-1a77b01 2017-09-15 16:58:02 [email protected]]
OPS=0x84
31 ab f1 38 a4 4e b b1 c6 9f 14 93 [1.440554 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-2: ATOS-V2.4-69-gc1e2fb5 #1 Wed Jan 31 06:57:06 UTC 2018 arm
INFO: BL3-2: Chip: GXL Rev: D (21:D - 80:2)
INFO: BL3-2: crypto engine DMA
INFO: BL3-2: secure time TEE
INFO: BL3-2: CONFIG_DEVICE_SECURE 0xb200000e
U-Boot 2015.01-gccdffc5-dirty (Nov 18 2018 - 10:53:49), Build: jenkins-oneday-430
DRAM: 2 GiB
Relocation Offset is: 76ed6000
gpio: pin gpiodv_24 (gpio 43) value is 1
gpio: pin gpioh_3 (gpio 52) value is 1
register usb cfg[0][1] = 0000000077f5f388
MMC: aml_priv->desc_buf = 0x0000000073ed6b40
aml_priv->desc_buf = 0x0000000073ed8e60
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
aml log : R1024 check pass!
start dts,buffer=0000000073edb690,dt_addr=0000000073edb690
get_partition_from_dts() 103: ret 0
parts: 14
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dto 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
07: rsv 0000000001000000 1
08: tee 0000000002000000 1
09: vendor 0000000006400000 1
10: oem 0000000012c00000 1
11: system 0000000046000000 1
12: cache 0000000010000000 2
13: data ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x17400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-2610: calc 723413d2, store 723413d2
_verify_dtb_checksum()-2610: calc 723413d2, store 723413d2
dtb_read()-2827: total valid 2
update_old_dtb()-2808: do nothing
aml log : R1024 check pass!
vpu: clk_level in dts: 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off finish
hpd_state=0
cvbs performance type = 6, table = 0
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[keymanage_dts_get_key_device]L85:carrier key name is not exist
[KM]Error:f[_get_km_ops_by_name]L231:key carrier not know device 4
[KM]Error:f[key_manage_query_exist]L546:There isn't dts cfg for key[carrier]
[KM]Error:f[key_manage_query_size]L503:Fail in query key exist
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f800000
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
pull down bt_reset
pull up bt_reset
set hci reset
04 0e 04 01 03 0c 00
set scan parameters
04 0e 04 01 0b 20 00
set scan enable
04 0e 04 01 0c 20 00
04 3e 2b 02 01 00 01 9d 53 be 6c e1 67 1f 02 01 02 03 03 9f fe 17 16 9f fe 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 cf
04 3e 16 02 01 04 01 9d 53 be 6c e1 67 0a 09 ff e0 00 01 43 a5 4c 5a 24 cd
04 3e 21 02 01 00 01 88 0a 0b 55 03 54 15 02 01 02 11 07 fc 9d d0 b3 cb 84 e0 84 06 42 f3 f7 e1 e0 bf cb b8
04 3e 0c 02 01 04 01 88 0a 0b 55 03 54 00 b8
pull down bt_enable
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
[imgread]szTimeStamp[2018111811300118]
[imgread]secureKernelImgSz=0xa96800
aml log : R-1024 check pass!
aml log : R1024 check pass!
aml log : R1024 check pass!
aml log : R1024 check pass!
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73f5b8e0
copy done
Kernel command line: buildvariant=user
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02604a00
Loading Ramdisk to 73cad000, end 73ec3800 ... OK
Loading Device Tree to 000000001fff1000, end 000000001ffff000 ... OK
Starting kernel ...
uboot time: 3849048 us
[ [email protected]] Booting Linux on physical CPU 0x0
[ [email protected]] Linux version 4.9.61-g92463ee ([email protected]) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Sun Nov 18 10:56:38 CST 2018
[ [email protected]] Boot CPU: AArch64 Processor [410fd034]
[ [email protected]] earlycon: aml_uart0 at MMIO 0x00000000c81004c0 (options '')
[ [email protected]] bootconsole [aml_uart0] enabled
[ [email protected]] efi: Getting EFI parameters from FDT:
[ [email protected]] efi: UEFI not found.
[ [email protected]] OF: reserved mem: __reserved_mem_alloc_size, start:5000000, end:7400000, len:2400000
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000005000000, size 36 MiB
[ [email protected]] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool
[ [email protected]] OF: reserved mem: __reserved_mem_alloc_size, start:7f800000, end:80000000, len:800000
[ [email protected]] Reserved memory: created CMA memory pool at 0x000000007f800000, size 8 MiB
[ [email protected]] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x000000007d800000, size 32 MiB
[ [email protected]] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000075c00000, size 124 MiB
[ [email protected]] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000074c00000, size 16 MiB
[ [email protected]] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created DMA memory pool at 0x0000000074c00000, size 0 MiB
[ [email protected]] OF: reserved mem: initialized node linux,ppmgr, compatible id shared-dma-pool
[ [email protected]] Reserved memory: created CMA memory pool at 0x0000000060800000, size 308 MiB
[ [email protected]] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
[ [email protected]] Reserved memory: unable to setup CMA region
[ [email protected]] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
[ [email protected]] cma: Reserved 8 MiB at 0x0000000074400000
[ [email protected]] psci: probing for conduit method from DT.
[ [email protected]] psci: PSCIv0.2 detected in firmware.
[ 0.000000[email protected]] psci: Using standard PSCI v0.2 function IDs
[ [email protected]] psci: Trusted OS migration not required
[ [email protected]] percpu: Embedded 23 pages/cpu @ffffffc074355000 s53528 r8192 d32488 u94208
[ [email protected]] Detected VIPT I-cache on CPU0
[ [email protected]] CPU features: enabling workaround for ARM erratum 845719
[ [email protected]] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 515844
[ [email protected]] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=enforcing logo=osd1,loaded,0x3d800000,576cvbs maxcpus=4 vout=576cvbs,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic androidboot.btmacaddr=c8:28:32:2d:a2:36 androidboot.wifimac=c8:28:32:2b:0a:26 androidboot.wificountrycode=US androidboot.bootloader=oneday androidboot.serialno=18554280002242 androidboot.rpmb_state=0 androidboot.verifiedbootstate=orange androidboot.slot_suffix=_a buildvariant=user
[ [email protected]] fb: osd1
[ [email protected]] fb: loaded
[ [email protected]] fb: 0x3d800000
[ [email protected]] fb: 576cvbs
[ [email protected]] vout: 576cvbs
[ [email protected]] vout: enable: 1
[ [email protected]] vout: get hdmimode: 1080p60hz
[ [email protected]] vout: get cvbsmode: 576cvbs
[ [email protected]] cvbs_out: cvbs performance line = 0
[ [email protected]] jtag: jtag select apao
[ [email protected]] (NULL device *): [mac_addr_set] try to wifi mac from emmc key!
[ [email protected]] (NULL device *): [mac_addr_set] uboot setup mac-addr: c8:28:32:2b:a:26
[ [email protected]] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ [email protected]] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ [email protected]] Memory: 1488104K/2096128K available (11644K kernel code, 1426K rwdata, 4472K rodata, 4416K init, 1434K bss, 63256K reserved, 544768K cma-reserved)
[ [email protected]] Virtual kernel memory layout:
[ [email protected]] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ [email protected]] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ [email protected]] .text : 0xffffff8009080000 - 0xffffff8009be0000 ( 11648 KB)
[ [email protected]] .rodata : 0xffffff8009be0000 - 0xffffff800a050000 ( 4544 KB)
[ [email protected]] .init : 0xffffff800a050000 - 0xffffff800a4a0000 ( 4416 KB)
[ [email protected]] .data : 0xffffff800a4a0000 - 0xffffff800a604a00 ( 1427 KB)
[ [email protected]] .bss : 0xffffff800a604a00 - 0xffffff800a76b324 ( 1435 KB)
[ [email protected]] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ [email protected]] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ [email protected]] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ [email protected]] 0xffffffbf00004000 - 0xffffffbf02000000 ( 31 MB actual)
[ [email protected]] memory : 0xffffffc000100000 - 0xffffffc080000000 ( 2047 MB)
[ [email protected]] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ [email protected]] Preemptible hierarchical RCU implementation.
[ [email protected]] Build-time adjustment of leaf fanout to 64.
[ [email protected]] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ [email protected]] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ [email protected]] NR_IRQS:64 nr_irqs:64 0
[ [email protected]] amlogic_init_sdemmc: register amlogic sdemmc clk
[ [email protected]] amlogic_init_sdemmc: register amlogic sdemmc clk
[ [email protected]] success set parent gpu_p1_composite rate to 400000000
[ [email protected]] amlogic_init_gpu: register meson gpu clk
[ [email protected]] amlogic_init_media: register meson media clk
[ [email protected]] amlogic_init_misc: register meson misc clk
[ [email protected]] gxl_clkc_init initialization complete
[ [email protected]] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.[email protected]] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ [email protected]] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ [email protected]] meson_bc_timer: mclk->mux_reg =ffffff8008006990,mclk->reg =ffffff8008008994
[ [email protected]] Console: colour dummy device 80x25
[ [email protected]] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ [email protected]] pid_max: default: 32768 minimum: 301
[ [email protected]] Security Framework initialized
[ [email protected]] SELinux: Initializing.
[ [email protected]] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] ftrace: allocating 38256 entries in 150 pages
[ [email protected]] sched-energy: CPU device node has no sched-energy-costs
[ [email protected]] CPU0: update cpu_capacity 1024
[ [email protected]] ASID allocator initialised with 65536 entries
[ [email protected]] EFI services will not be available.
[ [email protected]] Meson chip version = RevD (21:D - 84:0)
[ [email protected]] Detected VIPT I-cache on CPU1
[ [email protected]] CPU1: update cpu_capacity 1024
[ [email protected]] CPU1: Booted secondary processor [410fd034]
[ [email protected]] Detected VIPT I-cache on CPU2
[ [email protected]] CPU2: update cpu_capacity 1024
[ [email protected]] CPU2: Booted secondary processor [410fd034]
[ [email protected]] Detected VIPT I-cache on CPU3
[ [email protected]] CPU3: update cpu_capacity 1024
[ [email protected]] CPU3: Booted secondary processor [410fd034]
[ [email protected]] Brought up 4 CPUs
full bootlog at https://pastebin.com/GaRRd76p
Uboot env:
Code:
oneday#printenv
1080p60hz_deepcolor=444,8bit
1080p_h=1080
1080p_w=1920
1080p_x=0
1080p_y=0
480p60hz_deepcolor=rgb,8bit
EnableSelinux=enforcing
active_slot=_a
baudrate=115200
bcb_cmd=get_valid_slot;
boot_part=boot
bootargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=enforcing logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic androidboot.btmacaddr=c8:28:32:2d:a2:36 androidboot.wifimac=c8:28:32:2b:0a:26 androidboot.wificountrycode=US androidboot.bootloader=oneday androidboot.serialno=18554280002242 androidboot.rpmb_state=0 androidboot.verifiedbootstate=orange androidboot.slot_suffix=_a
bootcmd=run storeboot;
bootdelay=1
bootloader=oneday
bootup_offset=0x10dbbb0
bootup_size=0x5eec7a
btmac=c8:28:32:2d:a2:36
cmdline_keys=keyman init 0x1234; setkeys;
colorattribute=444,8bit
cvbs_drv=0
cvbsmode=576cvbs
display_bpp=24
display_color_bg=0
display_color_fg=0xffff
display_color_index=24
display_height=1080
display_layer=osd1
display_width=1920
dtb_mem_addr=0x1000000
factory_reset_poweroff_protect=echo wipe_data=${wipe_data}; echo wipe_cache=${wipe_cache};if test ${wipe_data} = failed; then run init_display; run storeargs;if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;fi; if test ${wipe_cache} = failed; then run init_display; run storeargs;if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;fi;
fb_addr=0x3d800000
fb_height=1080
fb_width=1920
fdt_high=0x20000000
firstboot=0
hdmimode=1080p60hz
init_display=osd open;osd clear;imgread pic logo bootup $loadaddr;bmp display $bootup_offset;bmp scale
initargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000
is.bestmode=false
jtag=apao
loadaddr=1080000
maxcpus=4
outputmode=1080p60hz
preboot=run cmdline_keys;run bcb_cmd; run factory_reset_poweroff_protect;run upgrade_check;run init_display;run storeargs;run switch_bootmode;
reboot_mode=cold_boot
recovery_from_flash=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};if itest ${upgrade_step} == 3; then if ext4load mmc 1:2 ${dtb_mem_addr} /recovery/dtb.img; then echo cache dtb.img loaded; fi;if ext4load mmc 1:2 ${loadaddr} /recovery/recovery.img; then echo cache recovery.img loaded; wipeisb; bootm ${loadaddr}; fi;else fi;if imgread kernel ${recovery_part} ${loadaddr} ${recovery_offset}; then wipeisb; bootm ${loadaddr}; fi;
recovery_from_udisk=setenv bootargs ${bootargs} aml_dt=${aml_dt} recovery_part={recovery_part} recovery_offset={recovery_offset};if fatload usb 0 ${loadaddr} aml_autoscript; then autoscr ${loadaddr}; fi;if fatload usb 0 ${loadaddr} recovery.img; then if fatload usb 0 ${dtb_mem_addr} dtb.img; then echo udisk dtb.img loaded; fi;wipeisb; bootm ${loadaddr};fi;
recovery_offset=0
recovery_part=recovery
rpmb_state=0
sdc_burning=sdc_burn ${sdcburncfg}
sdcburncfg=aml_sdc_burn.ini
serialno=18554280002242
sn2=3138353534323830303032323432
stderr=serial
stdin=serial
stdout=serial
storeargs=setenv bootargs ${initargs} androidboot.selinux=${EnableSelinux} logo=${display_layer},loaded,${fb_addr},${outputmode} maxcpus=${maxcpus} vout=${outputmode},enable hdmimode=${hdmimode} cvbsmode=${cvbsmode} hdmitx=${cecconfig} cvbsdrv=${cvbs_drv} androidboot.firstboot=${firstboot} jtag=${jtag}; setenv bootargs ${bootargs} androidboot.veritymode=enforcing androidboot.hardware=amlogic androidboot.btmacaddr=${btmac} androidboot.wifimac=${wifimac} androidboot.wificountrycode=${wifi_ccode} androidboot.bootloader=${bootloader} androidboot.serialno=${serialno};setenv bootargs ${bootargs} androidboot.rpmb_state=${rpmb_state};setenv bootargs ${bootargs} androidboot.verifiedbootstate=${verifiedbootstate};setenv bootargs ${bootargs} androidboot.slot_suffix=${active_slot};
storeboot=if imgread kernel ${boot_part} ${loadaddr}; then bootm ${loadaddr}; fi;run update;
switch_bootmode=get_rebootmode;if test ${reboot_mode} = factory_reset; then run recovery_from_flash;else if test ${reboot_mode} = update; then run update;else if test ${reboot_mode} = cold_boot; then else if test ${reboot_mode} = fastboot; then fastboot;fi;fi;fi;fi;if monitor_bt_cmdline; then run recovery_from_flash; fi;
try_auto_burn=update 700 750;
update=run usb_burning; run sdc_burning; if usb start 0; then run recovery_from_udisk;fi;run recovery_from_flash;
upgrade_check=echo upgrade_step=${upgrade_step}; if itest ${upgrade_step} == 3; then run init_display; run storeargs; run update;else fi;
upgrade_step=0
usb_burning=update 1000
verifiedbootstate=orange
wifi_ccode=US
wifimac=c8:28:32:2b:0a:26
wipe_cache=successful
wipe_data=successful
Click to expand...
Click to collapse
elitecop said:
hi i want to contact like this
this model cotact pin RX and TX?
Click to expand...
Click to collapse
Your board is not mdz-22-ab, so I can't help you with that. I have tried lots of contact points before I discovered right ones. Don't be affraid to experiment, you will find correct pins eventually.
l.capriotti said:
you did already, apologies!
Are you also able to revert to stock settings?
Would you pls boot a LibreELEC build...?
Click to expand...
Click to collapse
You can successfuly boot any s905x image from yadi.sk that uses same kernel version. some of them have kodi preinstalled, but drivers for wifi and sound do not work, so it's not very practical.
there is more in-depth information on mdz-16-ab linux on xda and also https://discourse.coreelec.org/t/xiaomi-mi-box-ce-and-drm/834.
all information on mdz-16-ab is also applicable to mdz-22-ab, as those boxes are very simmilar.
recrof said:
Your board is not mdz-22-ab, so I can't help you with that. I have tried lots of contact points before I discovered right ones. Don't be affraid to experiment, you will find correct pins eventually.
Click to expand...
Click to collapse
yes this board 3s, my board https://gadgetpage.ru/razbiraem-i-izuchaem/1828-razbor-tv-pristavki-xiaomi-mi-box-s.html
Do not burn the board while experimenting?
elitecop said:
yes this board 3s, my board https://gadgetpage.ru/razbiraem-i-izuchaem/1828-razbor-tv-pristavki-xiaomi-mi-box-s.html
Do not burn the board while experimenting?
Click to expand...
Click to collapse
There is always risk of burning the board, but it's very low.
error during boting
the box does not start!
I connected the box via serial usb, and this is the log:
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 90559
BL2 Built : 13:27:37, Oct 25 2017. gxl g56b77aa - [email protected]
_vcc5_power_init
rn5t567_power_init
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
Board ID = 5
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz - FAIL
DDR3 chl: Rank0 16bit @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 1008MHz - FAIL
DDR4 chl: Rank0 @ 1008MHz - FAIL
DDR4 chl: Rank0 16bit @ 1008MHz - FAIL
DDR init failed...
Reset...
-------------------------------------------------------------------------------------
Can you give me some advice?
Could this apply for mi box 4 mdz-21-aa?
Anyone found a way for root on latest android tv?
I connected the mibox 4c with cp2012 at windows 10
Hi, dear friend
I connected the mibox 4c with cp2012 at windows 10
, After I start the box and press ctl+c or space. Can not stop the uboot.i checked .
I checked the tx and Rx connection. It is OK.
How to fix it?
Maybe the xiaomi change something of uboot and disable the interruption ?
---------- Post added at 08:19 PM ---------- Previous post was at 08:03 PM ----------
This is my video of connection.
Please search andy漫漫说 at YouTube to get my channel and find the latest video.
I am newbie here. Can not post link .
Somebody help me ?
Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.06.28 05:39:49 =~=~=~=~=~=~=~=~=~=~=~=
GXL:BL1:9ac50e:bb16dc;FEAT:ADFC718C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 224076
BL2 Built : 18:13:36, Jun 17 2016.
gxl g176ecdb - [email protected]
set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 1
CPU clk: 1200MHz
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00014400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000cc400
NOTICE: BL3-1: v1.0(debug):ed1aadc
NOTICE: BL3-1: Built : 11:06:24, May 31 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3122-bcd5b77 2018-07-11 18:46:53 [email protected]]
OPS=0xc4
0 0 3 c c 0 d1 b3 40 a0 0 c4 [0.594431 Inits done]
secure task start!
high task start!
low task start!
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gfbef5dd (Sep 25 2018 - 15:03:01), Build: jenkins-transformers-627
DRAM: 1 GiB
Relocation Offset is: 36ea8000
gpio: pin gpiox_6 (gpio 6) value is 1
gpio: pin gpioao_4 (gpio 123) value is 1
register usb cfg[0][1] = 0000000037f64488
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
saradc_enable1 P_SAR_ADC_REG13: 0x0
saradc: check dts: FDT_ERR_BADMAGIC, load default parameters
saradc_enable2 P_SAR_ADC_REG13: 0x1100
MMC: aml_priv->desc_buf = 0x0000000033ea8f50
aml_priv->desc_buf = 0x0000000033eaaf60
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x4000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
saradc: check dts: FDT_ERR_BADMAGIC, load default parameters
get_adc_value ch(1) 79
aml_dt=gxl_tf_1g
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: tf variant: 1g
dtb 0 soc: gxl plat: tf vari: 1g
dtb 1 soc: gxl plat: tf vari: 2g
Find match dtb: 0
start dts,buffer=0000000033ead670,dt_addr=0000000033eade70
parts: 13
00: cache 0000000010000000 2
01: logo 0000000000300000 1
02: encrypt 0000000000100000 1
03: recovery 0000000002000000 1
04: tee 0000000000800000 1
05: crypt 0000000002000000 1
06: misc 0000000002000000 1
07: boot 0000000001400000 1
08: system 0000000040000000 1
09: backup 0000000020000000 4
10: persist 0000000000800000 4
11: panic 0000000000400000 4
12: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 400000 800000 0
2: cache c00000 10000000 2
3: env 10c00000 400000 0
4: logo 11000000 300000 1
5: encrypt 11300000 100000 1
6: recovery 11400000 2000000 1
7: tee 13400000 800000 1
8: crypt 13c00000 2000000 1
9: misc 15c00000 2000000 1
10: boot 17c00000 1400000 1
11: system 19000000 @ 40000000 1
12: backup 59000000 20000000 4
13: persist 79000000 800000 4
14: panic 79800000 400000 4
15: data 79c00000 158400000 4
mmc read lba=0x2000, blocks=0x2
mmc read lba=0x2002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x10c00000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hardware_version=1
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 3000
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
enc_vpu_bridge_reset[1183]
rx version is 1.4 or below div=10
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
aml_dt=gxl_tf_1g
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: tf variant: 1g
dtb 0 soc: gxl plat: tf vari: 1g
dtb 1 soc: gxl plat: tf vari: 2g
Find match dtb: 0
P_SAR_ADC_REG13: 0x1000
P_SAR_ADC_REG13 bak: 0x10
P_SAR_ADC_REG13: 0x1000
SEC_AO_SEC_SD_CFG12: 0xa040b3d1
ffu update start
old fw_ver = 6
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
wipe_data=successful
wipe_cache=successful
Boot command:
Boot status:
Boot message
""
upgrade_step=2
[OSD]load fb addr from dts
[OSD]failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]load fb addr from dts
[OSD]failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760, height=2160
pull down bt_reset
pull up bt_reset
set hci reset
bt_vendor_name = Realteck RTL8723DS
set scan parameters
set scan enable
pull down bt_enable
IR init done!
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f2d890
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02043d58
Loading Ramdisk to 33ded000, end 33e95658 ... OK
Loading Device Tree to 000000001fff4000, end 000000001ffffcda ... OK
Starting kernel ...
uboot time: 2655518 us
[ [email protected]] Initializing cgroup subsys cpuset
[ [email protected]] Initializing cgroup subsys cpu
[ [email protected]] Initializing cgroup subsys cpuacct
[ [email protected]] Linux version 3.14.29-301482-g2d0e095 ([email protected]) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Tue Sep 25 14:57:56 CST 2018
[ [email protected]] CPU: AArch64 Processor [410fd034] revision 4
[ [email protected]] no prop version_code
[ [email protected]] bootconsole [earlycon0] enabled
[ [email protected]] fdt Reserved memory table:
[ [email protected]] linux,meson-fb: 0x000000003e000000 - 0x0000000040000000 (32 MiB)
[ [email protected]] linux,di: 0x000000003c200000 - 0x000000003e000000 (30 MiB)
[ [email protected]] DI: DI reserved memory: created CMA memory pool at 0x000000003c200000, size 30 MiB
[ [email protected]] linux,ion-dev: 0x0000000039200000 - 0x000000003c200000 (48 MiB)
[ [email protected]] linux,ppmgr: 0x0000000039200000 - 0x0000000039200000 (0 MiB)
[ [email protected]] linux,codec_mm_cma: 0x0000000027c00000 - 0x0000000033c00000 (192 MiB)
[ [email protected]] linux,picdec: 0x0000000039200000 - 0x0000000039200000 (0 MiB)
[ [email protected]] Reserved memory: incorrect alignment of CMA region
[ [email protected]] linux,codec_mm_reserved: 0x0000000035100000 - 0x0000000039200000 (65 MiB)
[ [email protected]] fdt Reserved memory total: 370 MiB
[ [email protected]] psci: probing function IDs from device-tree
[ [email protected]] PERCPU: Embedded 12 pages/cpu @ffffffc0350a8000 s20224 r8192 d20736 u49152
[ [email protected]] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257539
[ [email protected]] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=osd1,loaded,0x3d800000,1080p60hz hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= vout=1080p60hz,enable cvbsdrv=0 boardver= jtag=apao androidboot.hardware=amlogic androidboot.firstboot=0 androidboot.btmac=00:00:00:00:00:00 androidboot.wifimac=c8:28:32:b7:c3:0e androidboot.wificountrycode=CN androidboot.serialno=17132/280733558 androidboot.selinux=enforcing androidboot.recoveryflag=false androidboot.hardware_version=1 androidboot.bootreason=cold_boot
[ [email protected]] logo: osd1
[ [email protected]] logo: loaded
[ [email protected]] logo: 0x3d800000
[ [email protected]] logo: 1080p60hz
[ [email protected]] logo: get hdmimode: 1080p60hz
[ [email protected]] logo: get cvbsmode: 576cvbs
[ [email protected]] vout_serve: 1080p60hz
[ [email protected]] vout_serve: enable: 1
[ [email protected]] tv_vout: cvbs performance line = 0
[ [email protected]] jtag: jtag select 2
[ [email protected]] (NULL device *): [mac_addr_set] try to wifi mac from emmc key!
[ [email protected]] (NULL device *): [mac_addr_set] uboot setup mac-addr: c8:28:32:b7:c3:e
[ [email protected]] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ [email protected]] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ [email protected]] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ [email protected]] Memory: 621540K/1044480K available (9852K kernel code, 1111K rwdata, 3956K rodata, 1216K init, 5803K bss, 422940K reserved)
[ [email protected]] Virtual kernel memory layout:
[ [email protected]] vmalloc : 0xffffff8000000000 - 0xffffff807fff0000 ( 2047 MB)
[ [email protected]] vmemmap : 0xffffff8080000000 - 0xffffff8080e00000 ( 14 MB)
[ [email protected]] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ [email protected]] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB)
[ [email protected]] .init : 0xffffffc001dfe000 - 0xffffffc001f2e000 ( 1216 kB)
[ [email protected]] .text : 0xffffffc001080000 - 0xffffffc001dfd334 ( 13813 kB)
[ [email protected]] .data : 0xffffffc001f2e000 - 0xffffffc002043d58 ( 1112 kB)
[ [email protected]] PM: Registered nosave memory: [mem 0x01080000-0x01dfcfff]
[ [email protected]] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ [email protected]] arch_multi_cluster:0
[ [email protected]] Preemptible hierarchical RCU implementation.
[ [email protected]] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ [email protected]] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ [email protected]] NR_IRQS:64 nr_irqs:64 0
[ [email protected]] Architected cp15 timer(s) running at 24.00MHz (phys).
[ [email protected]] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ [email protected]] meson_bc_timer: mclk->mux_reg =ffffff800000c990,mclk->reg =ffffff800000e994
[ [email protected]] Console: colour dummy device 80x25
[ [email protected]] allocated 4194304 bytes of page_cgroup
[ [email protected]] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ [email protected]] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ [email protected]] pid_max: default: 32768 minimum: 301
[ [email protected]] Security Framework initialized
[ [email protected]] SELinux: Initializing.
[ [email protected]] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ [email protected]] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[ [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[ [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[ [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[ [email protected]] Initializing cgroup subsys debug
[ [email protected]] Initializing cgroup subsys memory
[ [email protected]] Initializing cgroup subsys freezer
[ [email protected]] Initializing cgroup subsys blkio
[ [email protected]] ftrace: allocating 33470 entries in 131 pages
[ [email protected]] /cpus/[email protected]: Missing clock-frequency property
[ [email protected]] /cpus/[email protected]: Missing clock-frequency property
[ [email protected]] /cpus/[email protected]: Missing clock-frequency property
[ [email protected]] /cpus/[email protected]: Missing clock-frequency property
[ [email protected]] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ [email protected]] ftrace: Allocated trace_printk buffers
[ [email protected]] Meson chip version = RevC (21:C - C4:0)
[ [email protected]] CPU1: Booted secondary processor
[ [email protected]] CPU2: Booted secondary processor
[ [email protected]] CPU3: Booted secondary processor
[ [email protected]] Brought up 4 CPUs
[ [email protected]] SMP: Total of 4 processors activated.
[ [email protected]] sched: registering cpufreq notifiers for scale-invariant loads
[ [email protected]] instabooting: 0
[ [email protected]] pinctrl core: initialized pinctrl subsystem
[ [email protected]] regulator-dummy: no parameters
[ [email protected]] NET: Registered protocol family 16
[ [email protected]] ramoops: using module parameters
[ [email protected]] console [pstore-1] enabled
[ [email protected]] pstore: Registered ramoops as persistent store backend
[ [email protected]] ramoops: attached [email protected], ecc: 0/0
[ [email protected]] cpuidle: using governor menu
[ [email protected]] aml_vdac_init: module init
[ [email protected]] register canvas platform driver
[ [email protected]] register rdma platform driver
[ [email protected]] vdso: 2 pages (1 code, 1 data) at base ffffffc001f38000
[ [email protected]] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ [email protected]] DMA: preallocated 256 KiB pool for atomic allocations
[ [email protected]] software IO TLB [mem 0x26000000-0x26040000] (0MB) mapped at [ffffffc026000000-ffffffc02603ffff]
[ [email protected]] Serial: AMBA PL011 UART driver
[ [email protected]] aml_i2c version: 20140813
[ [email protected]] i2c-core: driver [pmu4] using legacy resume method
[ [email protected]] codec_mm:codec_mm_module_init
[ [email protected]] aml_watch_point_probe, in
[ [email protected]] gxbb_mpll_clk: register mpll_clk_out0 success done
[ [email protected]] gxbb_mpll_clk: register mpll_clk_out1 success done
[ [email protected]] gxbb_mpll_clk: register mpll_clk_out2 success done
[ [email protected]] clk_sys: register PLL sys_pll success done
[ [email protected]] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
[ [email protected]] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
[ [email protected]] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
[ [email protected]] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
[ [email protected]] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
[ [email protected]] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
[ [email protected]] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
[ [email protected]] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
[ [email protected]] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
[ [email protected]] gxl_clk: clock initialization complete
[ [email protected]] clkmsr: Gxl msr_clk_reg0=ffffff800003a75c,msr_clk_reg2=ffffff800003c764
[ [email protected]] aml_iomap: amlogic iomap probe done
[ [email protected]] pinmux-gxl c1109880.pinmux: Init pinux probe!
[ [email protected]] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[ [email protected]] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ [email protected]] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ [email protected]] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ [email protected]] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ [email protected]] codec_mm has 2 memory regions
[ [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_cma ok
[ [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_reserved ok
[ [email protected]] codec_mm has 2 memory regions
[ [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_cma ok
[ [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_reserved ok
[ [email protected]] vpu: driver version: v02
[ [email protected]] vpu: load vpu_clk: 666667000Hz(7)
[ [email protected]] vpu: vpu_probe OK
[ [email protected]] tv_vout: tvout_probe
[ [email protected]] tv_vout: major number 254 for disp
[ [email protected]] vout_notify: vout_register_server
[ [email protected]] tv_vout: register tv module server ok
[ [email protected]] tv_vout: tvout_probe OK
[ [email protected]] canvas_probe reg=00000000c8838000,size=400
[ [email protected]] canvas maped reg_base =ffffff800008e000
[ [email protected]] rdma_probe
[ [email protected]] bio: create slab <bio-0> at 0
[ [email protected]] SCSI subsystem initialized
[ [email protected]] usbcore: registered new interface driver usbfs
[ [email protected]] usbcore: registered new interface driver hub
[ [email protected]] usbcore: registered new device driver usb
[ [email protected]] i2c-gpio i2c_gpio.35: using pins 172 (SDA) and 173 (SCL)
[ [email protected]] Linux video capture interface: v2.00
[ [email protected]] pps_core: LinuxPPS API ver. 1 registered
[ [email protected]] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ [email protected]] PTP clock support registered
[ [email protected]] hdmitx: system: amhdmitx_init
[ [email protected]] hdmitx: system: Ver: 2014May6
[ [email protected]] hdmitx: system: amhdmitx_probe
[ [email protected]] ------------[ cut here ]------------
[ [email protected]] WARNING: CPU: 0 PID: 1 at /home/work/data/jenkins/workspace/transformers/common/drivers/base/core.c:549 device_create_file+0xa4/0xbc()
[ [email protected]] Attribute product_name: write permission without 'store'
[ [email protected]] Modules linked in:
[ [email protected]] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.29-301482-g2d0e095 #1
[ [email protected]] Call trace:
[ [email protected]] [<ffffffc0010894d8>] dump_backtrace+0x0/0x144
[ [email protected]] [<ffffffc001089638>] show_stack+0x1c/0x28
[ [email protected]] [<ffffffc001a0b108>] dump_stack+0x74/0xb8
[ [email protected]] [<ffffffc0010a0088>] warn_slowpath_common+0x98/0xc0
[ [email protected]] [<ffffffc0010a0124>] warn_slowpath_fmt+0x74/0x88
[ [email protected]] [<ffffffc001454cd4>] device_create_file+0xa0/0xbc
[ [email protected]] [<ffffffc00163fa14>] amhdmitx_probe+0x2ac/0x924
[ [email protected]] [<ffffffc00145bc68>] platform_drv_probe+0x28/0x60
[ [email protected]] [<ffffffc001459bd4>] really_probe+0xd4/0x244
[ [email protected]] [<ffffffc001459e68>] __driver_attach+0xb0/0xb8
[ [email protected]] [<ffffffc001457c3c>] bus_for_each_dev+0x68/0xac
[ [email protected]] [<ffffffc001459684>] driver_attach+0x28/0x34
[ [email protected]] [<ffffffc00145928c>] bus_add_driver+0x158/0x210
[ [email protected]] [<ffffffc00145a624>] driver_register+0x64/0x124
[ [email protected]] [<ffffffc00145bc30>] __platform_driver_register+0x74/0x84
[ [email protected]] [<ffffffc001e36d4c>] amhdmitx_init+0x5c/0xa4
[ [email protected]] [<ffffffc0010816a4>] do_one_initcall+0xd4/0x138
[ [email protected]] [<ffffffc001dfe990>] kernel_init_freeable+0x19c/0x23c
[ [email protected]] [<ffffffc001a05d48>] kernel_init+0x1c/0xdc
[ [email protected]] ---[ end trace da93876e7f41ceba ]---
[ [email protected]] ------------[ cut here ]------------
[ [email protected]] WARNING: CPU: 0 PID: 1 at /home/work/data/jenkins/workspace/transformers/common/drivers/base/core.c:549 device_create_file+0xa4/0xbc()
[ [email protected]] Attribute prefer_mode: write permission without 'store'
[ [email protected]] Modules linked in:
[ [email protected]] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.14.29-301482-g2d0e095 #1
[ [email protected]] Call trace:
[ [email protected]] [<ffffffc0010894d8>] dump_backtrace+0x0/0x144
[ [email protected]] [<ffffffc001089638>] show_stack+0x1c/0x28
[ [email protected]] [<ffffffc001a0b108>] dump_stack+0x74/0xb8
[ [email protected]] [<ffffffc0010a0088>] warn_slowpath_common+0x98/0xc0
[ [email protected]] [<ffffffc0010a0124>] warn_slowpath_fmt+0x74/0x88
[ [email protected]] [<ffffffc001454cd4>] device_create_file+0xa0/0xbc
[ [email protected]] [<ffffffc00163fa20>] amhdmitx_probe+0x2b8/0x924
[ [email protected]] [<ffffffc00145bc68>] platform_drv_probe+0x28/0x60
[ [email protected]] [<ffffffc001459bd4>] really_probe+0xd4/0x244
[ [email protected]] [<ffffffc001459e68>] __driver_attach+0xb0/0xb8
[ [email protected]] [<ffffffc001457c3c>] bus_for_each_dev+0x68/0xac
[ [email protected]] [<ffffffc001459684>] driver_attach+0x28/0x34
[ [email protected]] [<ffffffc00145928c>] bus_add_driver+0x158/0x210
[ [email protected]] [<ffffffc00145a624>] driver_register+0x64/0x124
[ [email protected]] [<ffffffc00145bc30>] __platform_driver_register+0x74/0x84
[ [email protected]] [<ffffffc001e36d4c>] amhdmitx_init+0x5c/0xa4
[ [email protected]] [<ffffffc0010816a4>] do_one_initcall+0xd4/0x138
[ [email protected]] [<ffffffc001dfe990>] kernel_init_freeable+0x19c/0x23c
[ [email protected]] [<ffffffc001a05d48>] kernel_init+0x1c/0xdc
[ [email protected]] ---[ end trace da93876e7f41cebb ]---
[ [email protected]] hdmitx: system: not find match init-data
[ [email protected]] hdmitx: system: not find match pwr-ctl
[ [email protected]] hdmitx hpd irq = 89
[ [email protected]] hdmitx20: Mapped PHY: 0xc0800000
[ [email protected]] hdmitx20: Mapped PHY: 0xc1104400
[ [email protected]] hdmitx20: Mapped PHY: 0xc8100000
[ [email protected]] hdmitx20: Mapped PHY: 0xc8834000
[ [email protected]] hdmitx20: Mapped PHY: 0xc883a000
[ [email protected]] hdmitx20: Mapped PHY: 0xc883c000
[ [email protected]] hdmitx20: Mapped PHY: 0xd0100000
[ [email protected]] hdmitx20: Mapped PHY: 0xda83a000
[ [email protected]] hdmitx: alread display in uboot 0x10
[ [email protected]] avmute set to 1
[ [email protected]] vout_serve: vout_init_module
[ [email protected]] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[ [email protected]] hdmitx: system: irq 2
[ [email protected]] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[ [email protected]] tv_vout: already display in uboot
[ [email protected]] vout_serve: vinfo mode is: 1080p60hz
[ [email protected]] vout_serve: init mode 1080p60hz
[ [email protected]] vout_serve: create vout attribute OK
[ [email protected]] vout_serve: meson_vout_probe OK
[ [email protected]] logo: logo_init
[ [email protected]] osd_rdma: osd_rdma_init: rdma_table p=0x34841000,op=0x34841000 , v=0xffffff80000a9000
[ [email protected]] osd_rdma: osd rdma request irq as second interrput function!
[ [email protected]] Advanced Linux Sound Architecture Driver Initialized.
[ [email protected]] Bluetooth: Core ver 2.18
[ [email protected]] NET: Registered protocol family 31
[ [email protected]] Bluetooth: HCI device and connection manager initialized
[ [email protected]] Bluetooth: HCI socket layer initialized
[ [email protected]] Bluetooth: L2CAP socket layer initialized
[ [email protected]] Bluetooth: SCO socket layer initialized
[ [email protected]] cfg80211: Calling CRDA to update world regulatory domain
[ [email protected]] NetLabel: Initializing
[ [email protected]] NetLabel: domain hash size = 128
[ [email protected]] NetLabel: protocols = UNLABELED CIPSOv4
[ [email protected]] NetLabel: unlabeled traffic allowed by default
[ [email protected]] Switched to clocksource arch_sys_counter
[ [email protected]] ktrace : kp ktrace init OK
[ [email protected]] ktrace : event ktrace init OK
[ [email protected]] ktrace : mm ktrace init OK
[ [email protected]] ktrace : sched ktrace init OK
[ [email protected]] ktrace : binder ktrace init OK
[ [email protected]] ktrace : cpufreq ktrace init OK
[ [email protected]] ktrace : ktrace init OK
[ [email protected]] [amlatvdemod..]aml_atvdemod_init.
[ [email protected]] NET: Registered protocol family 2
[ [email protected]] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ [email protected]] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ [email protected]] TCP: Hash tables configured (established 8192 bind 8192)
[ [email protected]] TCP: reno registered
[ [email protected]] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ [email protected]] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ [email protected]] NET: Registered protocol family 1
[ [email protected]] aml_wifi wifi.31: [wifi_dev_probe] no power_on_pin2
[ [email protected]] aml_wifi wifi.31: [wifi_dev_probe] set pwm as 32k output
[ [email protected]] aml_wifi wifi.31: [wifi_dev_probe] interrupt_pin=241
[ [email protected]] aml_wifi wifi.31: [wifi_dev_probe] irq_num=100, irq_trigger_type=0
[ [email protected]] aml_wifi wifi.31: [wifi_dev_probe] power_on_pin=229
[ [email protected]] aml_wifi wifi.31: [wifi_dev_probe] clock_32k_pin=0
[ [email protected]] aml_wifi wifi.31: [wifi_setup_dt] wifi_setup_dt
[ [email protected]] aml_wifi wifi.31: [wifi_setup_dt] interrupt_pin(241)
[ [email protected]] aml_wifi wifi.31: [wifi_setup_dt] power_on_pin(229)
[ [email protected]] Unpacking initramfs...
[ [email protected]] Freeing initrd memory: 672K (ffffffc033ded000 - ffffffc033e95000)
[ [email protected]] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ [email protected]] audit: initializing netlink subsys (disabled)
[ [email protected]] audit: type=2000 audit(1.470:1): initialized
[ [email protected]] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ [email protected]] VFS: Disk quotas dquot_6.5.2
[ [email protected]] hdmitx: plugin
[ [email protected]] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ [email protected]] fuse init (API version 7.22)
[ [email protected]] msgmni has been set to 1679
[ [email protected]] NET: Registered protocol family 38
[ [email protected]] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ [email protected]] io scheduler noop registered
[ [email protected]] io scheduler deadline registered
[ [email protected]] io scheduler cfq registered (default)
[ [email protected]] meson-rng c8834000.rng: hwrng registered
[ [email protected]] loop: module loaded
[ [email protected]] zram: Created 1 device(s) ...
[ [email protected]] tun: Universal TUN/TAP device driver, 1.6
[ [email protected]] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ [email protected]] PPP generic driver version 2.4.2
[ [email protected]] PPP BSD Compression module registered
[ [email protected]] PPP Deflate Compression module registered
[ [email protected]] PPP MPPE Compression module registered
[ [email protected]] NET: Registered protocol family 24
[ [email protected]] hdmitx: edid: check sum valid
[ [email protected]] hdmitx: edid: check sum valid
[ [email protected]] hdmitx: edid: blk0 raw data
[ [email protected]] 00ffffffffffff003674010be903000000100103804627780a1990a755469824
[ [email protected]] 10494b2108008bc0814081c061400101010101010101011d007251d01e206e28
[ [email protected]] 5500c48e2100001e011d8018711c1620582c2500c48e2100009e000000fc0050
[ [email protected]] 524f4a4543544f52530a2020000000fd0016500e5b10000a20202020202001e1
[ [email protected]]
[ [email protected]]
[ [email protected]] hdmitx: edid: blk1 raw data
[ [email protected]] 02031df24a0102038405101293141f230907078301000065030c0010008c0ad0
[ [email protected]] 8a20e02d10103e9600138e21000018011d00bc52d01e20b8285540c48e210000
[ [email protected]] 1e011d80d0721c1620102c2580c48e2100009e8c0ad08a20e02d10103e9600c4
[ [email protected]] 8e210000188c0ad090204031200c405500c48e2100001800000000000000002b
[ [email protected]]
[ [email protected]]
[ [email protected]] EDID Parser:
[ [email protected]] hdmitx: edid: find IEEEOUT
[ [email protected]]
[ [email protected]] hdmitx: edid: check sum valid
[ [email protected]] hdmitx: edid: check sum valid
[ [email protected]] hdmitx: update RX hdr info 0
[ [email protected]] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[ [email protected]] hdmitx: video: get current mode: 1080p60hz
[ [email protected]] hdmitx: update rx hdr info 0
[ [email protected]] hdmitx: get ext_name
[ [email protected]] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[ [email protected]] hdmtix: set audio
[ [email protected]] hdmitx tx_aud_src = 0
[ [email protected]] hdmitx: system: irq 80000001
[ [email protected]] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ [email protected]] hdmitx aud_n_para = 6144
[ [email protected]] hdmitx set channel status
[ [email protected]] Start = 0x10000100 End = 0x100001ff
[ [email protected]] [0x10000103]: 0x00000008
[ [email protected]] [0x10000104]: 0x00000001
[ [email protected]] [0x10000170]: 0x00000010
[ [email protected]] [0x10000180]: 0x000000ff
[ [email protected]] [0x10000181]: 0x000000ff
[ [email protected]] [0x10000182]: 0x00000003
[ [email protected]] [0x10000183]: 0x00000007
[ [email protected]] [0x10000184]: 0x0000003f
[ [email protected]] [0x10000185]: 0x00000002
MDZ-22 ab crashed
Hello togehter,
I new in the rforum and need support.
I think I crashed mz mdy-22ab bz upadting new version via USB, since this i cannot enter reoverz mode.
I followed the describtion to enter via UART and Putty and got the following.
Due the fact that i am not an expert i don^t know wht the puttz.log means.
Maybe some experts in the forum can help me.
Reset...
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 99019
BL2 Built : 13:27:37, Oct 25 2017. gxl g56b77aa - [email protected]
_vcc5_power_init
rn5t567_power_init
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
Board ID = 5
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz - FAIL
DDR3 chl: Rank0 16bit @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 1008MHz - FAIL
DDR4 chl: Rank0 @ 1008MHz - FAIL
DDR4 chl: Rank0 16bit @ 1008MHz - FAIL
DDR init failed...
Reset...
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 99323
Same me..(((
I can't find any link to download Armbian_5.34_S9xxx_Ubuntu_xenial_4.9.40_mate_20171 112. Can someone reupload it?
Can I do it with regular usb rs232 cable?I have to solder it?Is there newer builds avalible?