Okay, I'm not sure exactly what you'll need to know to help, so I'll just tell you what I think is important....
Current situation:
- If I boot the phone normally it freezes at the SONY screen and goes no further.
- If I attempt to boot into recovery mode, it loads the CWM screen (logo in the middle with instructions at bottom), but no actual menu or options. After about 5 seconds, this screen disappears, the phone reboots and then gets stuck on the SONY screen.
- If I connect the phone to the computer in Flashmode Flashtool recognizes it as being connected, but regardless of what I do, after about 2mins the phone reboots, loses connection with the computer, and freezes on the SONY screen as before mentioned.
- If I connect the phone to the computer normally while stuck on the SONY screen, the PC recognizes it though doesn't allow me to do anything to it, and Flashtool says I need to install drivers (I have installed every driver that comes with Flashtool).
How I got here:
- I've rooted the phone
- I've flashed Z2_DooMLoRD_AdvStkKernel_FW-438-v05
- I've unlocked the bootloader (via Flashtool)
- I've installed [Rom][Unofficial]Slim Rom 4.4.4 based on CM11.0, ROM for the Sony Xperia Z2
The phone was okay up until this point, however I wasn't happy with the ROM so I tried to reboot into recovery mode to wipe and install Carbon. This is when the trouble began.
Now it seems I can't do anything :/
Please help. This phone is literally 3 days and it looks like I've completely screwed it >.<
Thanks!
How to recover your device from almost any kind of brick
Requirements
Check the pinned sites
Flashtool
FTF of choice for your device
2 Rubber bands (I am serious but only if your device has no response)
Step1
unplug your device from anything
open flashtool on your pc
plug your cable into your PC
do not plug the cable into your device
Step2
Hold your power button and your volume up button at the same time
your device should buzz 3 times
(this should take a few secconds)
if it does not take a few seconds then you need to put a rubber band around your device holding your power button and your volume up button, DO NOT LEAVE MORE THAN IT NEEDS TO BE LEFT, wait patiently for your device to buzz 3 times
Step 3
once your device has buzzed 3 times you are free to flash a FTF as your device is powered off
step4
if you dont know how to flash a FTF but have gotten as far as installing flashtool,Z2 drivers and downloading a FTF FOR YOUR DEVICE... then folow this step
within your flashtool window click on the lightning icon at the top left
select flashmode
navigate to where you downloaded your FTF (OR put your FTF in your /flashtool/firmwares folder)
select your FTF
Flashtool should give you a prompt to plug in your device
hold volume down and plug in your device
step5
wait for it to finish flashing
step6
your device is now recovered, enjoy...
Sent from my D6503 using XDA Premium 4 mobile app
I bricked my phone doing this:
- root with eazyroot
- installed dual recovery
- full wipe
- install carbon + gapps
bum... bricked
i cant even see the Sony logo
Then i use the method mentioned by Envious_Data and my phone returned from hell
Good luck dude... hope u can fix that
carloscarvalho said:
I bricked my phone doing this:
- root with eazyroot
- installed dual recovery
- full wipe
- install carbon + gapps
bum... bricked
i cant even see the Sony logo
Then i use the method mentioned by Envious_Data and my phone returned from hell
Good luck dude... hope u can fix that
Click to expand...
Click to collapse
You didn't unlock your bootloader?
Isn't Carbon ROM AOSP?
If it is, it needs an unlocked bootloader or it will get bricked
Unbalanced said:
Okay, I'm not sure exactly what you'll need to know to help, so I'll just tell you what I think is important....
Current situation:
- If I boot the phone normally it freezes at the SONY screen and goes no further.
- If I attempt to boot into recovery mode, it loads the CWM screen (logo in the middle with instructions at bottom), but no actual menu or options. After about 5 seconds, this screen disappears, the phone reboots and then gets stuck on the SONY screen.
- If I connect the phone to the computer in Flashmode Flashtool recognizes it as being connected, but regardless of what I do, after about 2mins the phone reboots, loses connection with the computer, and freezes on the SONY screen as before mentioned.
- If I connect the phone to the computer normally while stuck on the SONY screen, the PC recognizes it though doesn't allow me to do anything to it, and Flashtool says I need to install drivers (I have installed every driver that comes with Flashtool).
How I got here:
- I've rooted the phone
- I've flashed Z2_DooMLoRD_AdvStkKernel_FW-438-v05
- I've unlocked the bootloader (via Flashtool)
- I've installed [Rom][Unofficial]Slim Rom 4.4.4 based on CM11.0, ROM for the Sony Xperia Z2
The phone was okay up until this point, however I wasn't happy with the ROM so I tried to reboot into recovery mode to wipe and install Carbon. This is when the trouble began.
Now it seems I can't do anything :/
Please help. This phone is literally 3 days and it looks like I've completely screwed it >.<
Thanks!
Click to expand...
Click to collapse
Okay I used to get into this kind of situation when I used HTC One, and what I did is try to flash recovery and unlocked bootloader again "using command".
And problem has solved. I think it is pretty much same for Xperia Z2, (ftf flashing method is not useful in this situation.)
I hope you know how to flash custom recovery using command. If not I think there is some thread that explains how to flash recovery and unlock the bootloader using command, if you can't find it plz let me know. Hope you have recovered phone next time I check this thread. Good luck mate :good:
HussainQ said:
You didn't unlock your bootloader?
Isn't Carbon ROM AOSP?
If it is, it needs an unlocked bootloader or it will get bricked
Click to expand...
Click to collapse
Yeah... I know... A newbie mistake...
I Just follow the instruction available in the site. And there is just "root and recovery"
No bootloader mentioned
But u r right... Thats the reason
Sent from my awesome Xperia Z2 using XDA Premium
@Envious_Data: Bro, thank you so much for that. I my z2 have only 1 day, and i god damn it bricket, that even screen wasn't working. So for other people who had bad luck: first I rooted using Community Rootkit, then unlocked bootloader, and at the end I flashed via fastboot boot.img which one i extracted from zip file from this thread - http://forum.xda-developers.com/showthread.php?t=2702001. Command prompt showed that it works. I rebooted phone sony logo showed up, but then disappeared, and then was crying and sorrow. Three years of rooting,flashing without any problem, and now that. Thank you one more time, that's a great lesson
I do have some advice for people
1. Try to find help threads for your device, i have one for Z2 that gives some useful info, ill be adding more soon
2. Once you have got the jist of flashing then try to expand on that, i do recomend roms first because its harder to brick from a rom than a kernel or a non stock based rom such as CM11 or AOSP
3. Always keep a stock flashable rom (kernel too if you have a unlocked bootloader) on your device
Sent from my D6503 using XDA Premium 4 mobile app
I too hard brick my Z2, only solution is the same as for Z1 http://forum.xda-developers.com/showthread.php?t=2646405
Sorry friend :`
discipuloosho said:
I too hard brick my Z2, only solution is the same as for Z1 http://forum.xda-developers.com/showthread.php?t=2646405
Sorry friend :`
Click to expand...
Click to collapse
A hard brick is by definition not recoverable by the user, requiring either special equipment ie jtag or RMA to fix.
I am quite surprised, and intrigued, at people flashing cm or AOSP on a two day old phone, was Sony experience that awful? You'd maybe be better served with a nexus device.
ghostofcain said:
A hard brick is by definition not recoverable by the user, requiring either special equipment ie jtag or RMA to fix.
I am quite surprised, and intrigued, at people flashing cm or AOSP on a two day old phone, was Sony experience that awful? You'd maybe be better served with a nexus device.
Click to expand...
Click to collapse
True friend, but I had an Xperia MT11i (Neo V) and all (fastboot, flashtool, CM, etc) was always no problem.
I've taken today for service (with CM11 (and cm kernel)) and see what happens ...
@Unbalanced I don't think your Z2 Hardbricked, if it were not ignite. Luck
Hi all, if it helps I did the same thing last night. Flashed CM11 without a recovery and wanted to revert back to my nandroid backup. I flashed doomloards kernal via fastboot. CWM started with no menu and just bootlooped. I then thought it may be a CWM issue, maybe no file structure or something. I flashed XZDuelKernal via fastboot and booted into CWM again and experienced the same issue. As this is a duel recovery, I then booted into TWRP. Recovery started and I was able to flash another zip then recover my nandroid backup. If you get this menu issue with CWM,try and flash a TWRP recovery and boot into that.
Also, as mentioned before, this is not a hard brick. It's just incompatible software and is easily fixed if you know what you are doing and prepared (nandroid backup, knowledge about fastboot and flashmode, ftf, recovery, unlocked bootloader).
Sent from my D6503 using Tapatalk
Stuck
Hi.
I believe (although I'm not sure) that I have bricked my Xperia Z2 in some way. When I press the 'power' button, the phone vibrates once and does nothing. I have tried to hold the 'power on' and 'volume up' buttons for a long time (half an hour with rubber bands), and nothing happens (as explained earlier in the thread).
I believe I am able to access the fastboot though, through 'Terminal' app on OSX. From there I can " ./fastboot devices " and get confirmation that they have loaded. I am also able to perform other tasks from here, such as flashing a recovery and " fastboot erase system -w " (which I believe may have got me to where I am now). I've been following things on this thread: http://forum.xda-developers.com/showthread.php?t=2277112
I have no experience in rooting or flashing, but attempted to flash a custom ROM because there were step by step instructions.
Anyway, I firstly used Sony's rooting procedure whereby an unlock code is generated etc. Eventually I gained access to the Recovery mode (via clockwork), and wiped the phone, installed the ROMAur zip and GApps zip. However, when I booted, it kept giving me warnings saying the apps were crashing. I've since gotten lost completely and need someone to help bail me out.
I'm hoping I can sort things out via the fastboot.
Thanks in advance for your help.
scoobard said:
Hi.
I believe (although I'm not sure) that I have bricked my Xperia Z2 in some way. When I press the 'power' button, the phone vibrates once and does nothing. I have tried to hold the 'power on' and 'volume up' buttons for a long time (half an hour with rubber bands), and nothing happens (as explained earlier in the thread).
I believe I am able to access the fastboot though, through 'Terminal' app on OSX. From there I can " ./fastboot devices " and get confirmation that they have loaded. I am also able to perform other tasks from here, such as flashing a recovery and " fastboot erase system -w " (which I believe may have got me to where I am now). I've been following things on this thread: http://forum.xda-developers.com/showthread.php?t=2277112
I have no experience in rooting or flashing, but attempted to flash a custom ROM because there were step by step instructions.
Anyway, I firstly used Sony's rooting procedure whereby an unlock code is generated etc. Eventually I gained access to the Recovery mode (via clockwork), and wiped the phone, installed the ROMAur zip and GApps zip. However, when I booted, it kept giving me warnings saying the apps were crashing. I've since gotten lost completely and need someone to help bail me out.
I'm hoping I can sort things out via the fastboot.
Thanks in advance for your help.
Click to expand...
Click to collapse
Download ftf file for your device and flash via flashtool.
mariosraptor said:
Download ftf file for your device and flash via flashtool.
Click to expand...
Click to collapse
Thanks for the quick reply Mario. I did just that (using Kuwait FFT for the D6503), and everything appears to be back to normal. Unfortunately I still have not got root access and can't remove the bloatware. As for the bricking issue however, it's solved. Thanks.
Is there a rooting section or something? I feel as if this may be in the wrong section (if so, please move it thanks)
So, today, I decided that I wanted to unlock, root, and install a custom ROM on my htc m9. Now, on my previous phone, I only rooted and installed a custom kernal, all of which were apps that I used on my phone to do all the work. for the m9, there are no apps that root the phone for you so I looked up a few tutorials. (I'll list what I did in case you find something I did wrong
list of my guides :
droidviews.com/root-htc-one-m9-marshmallow
.droidviews.com/how-to-root-htc-one-m9-and-install-twrp-recovery-on-it/
and I used htc dev to unlock my phone's bootloader
unlocking my bootloader.
Unlocking my bootloader was successful, when I go into download mode (the black screen to be clear) it says unlocked
installing twrp
There was a lot of issues when installing since all but one of the guides kept saying go into bootloader mode, bootloader mode this, bootloader mode that (which is the white screen). After some searching, I realized that they really meant download mode... two different things... I believe twrp was successfully downloaded since I am able to access twrp when I go into bootloader mode, then recovery mode, and I end up in twrp.
rooting
so, according to the guide, I move the supersu zip files into my internal storage (anywhere). then go into twrp, press install, select the zip file, then swipe to flash.
well, I did just that, however, when I go to turn on my phone, I get stuck on the htc load screen, It's not a boot loop, it's just that white screen that says htc... I can't do anything else. holding down the power button does nothing (even for 10 seconds)... update, after typing this, I get a nice animation, then I'm stuck on the white screen that says htc one...holding the power button again does nothing, power button, and volume down does nothing... I think if I hold the power button and volume up, I turn off the phone, meaning I can access download mode, boot loader mode, etc. So... now what? clearly, following instruction has got me not where (bummer) and my lack of experience has also gotten in trouble (it could be worse? right?) what can I do to fix this?
note: my previous phone, I soft bricked it and I was able to flash the stock rom with LG flash tool, but there's no such thing as htc flash tool...
Hello,
Im new here and im not sure if here is the correct place to ask questions but,
I have a Huawei Y5 II and i was trying to put android 6.0 or higher but i had alot of problems.
I first unlocked my bootloader and then installed a custom recovery TWRP and CWM on it, but i never succeeded in booting into one of them.
What happened is that i saw in a post here on xda that with a certain command in fastboot mode i can remove the custom recoveries ( because they didnt work at all) but when i did it i ended up formatting my whole system,cache and boot.
Now my phone just stays on the huawei logo when i turn it on and nothing else.
i tried to install a custom recovery again throught the fastboot mode using adb on my pc, but when i press the vol up+ power my phone just keeps restarting and restarting and staying on the logo.
Thanks in advance for your time spent on reading my problem i just wanna use my phone again cuz i love it. <3
Hi, try to flash latest stock firmware for SD update here is example but do for your model and region !!!
http://huawei-firmware.com/rom/huawei-y5ii/cunu29/1719
Good Luck
Thanks you, but i would do that if i had access to my recovery!
If i press the keys my phone just restarts and restarts until i let the keys off, then again... just the logo.
my phone still is in warranty and i can give it to my distributor so their service fixes it.... but i dont really want that.. i just wanna fix it and use it as before.
well..
i had my phone to service and i got it fixed for 100 bucks. :/ i really am a sadman
Hi Community,
I read some posts how to fix my Problem, but i cant go to a service Point.
So I was using the Evolution X for a long Time (Installed with TWRP 3.1.0).
And now i wanted to change to the Nusantara Project (Vanilla), I did a clean Flash, everything worked i could access the System.
Than i had problems installing Play Store, so i rebooted into Recovery via the System. But now im Stuck in the Loop.
Can i Somehow connect my Phone to the PC and Reset?
Can someone tell me if i Hard/soft bricked my phone ?
Just a little advice, would be really appreciated.
Thanks a lot
Go to TWRP, wipe system, cache, data and dalvik. Now flash nusantra and whichever GApps are recommended for it (if there are no recommendations then use OpenGApps, make sure the architecture is correct). Now wipe dalvik and restart. Sometimes, certain roms begin to bootloop if you boot into the rom first, then try to install gapps later.
If you still have issues, just reflash the stock rom.
I cant access the TWRP anymore, im just stuck on the Bootloader, no matter how i turn on The Phone (Volume Up + Power ON ), (Volume Down + Power), (All 3 Buttons)
Nothing works anymore i dont understand ....
Im searching the net but i cant go to fastboot or something else, its just keeps on rebooting ...
So it's bootlooping, but you cant access recovery?
When the screen turns off, press the key combo and it should go to recovery.
Your best bet is to take it to a service centre, but if that really isn't possible for you, then wait for its battery to drain completely, then when you plug in the charger, instead of turning the phone on, press the key combo to enter the recovery. From there, wipe and flash some other OS.
I've also heard that certain versions of TWRP don't support some roms, leading to a bootloop. In that case, you'll have to use orangefox recovery to flash the rom (orangefox is flashable via twrp)
Yes its Bootlooping.
When i turn it on, on the Left Corner "Recovery Mode" blinks for one second. Than the usual Text appears:
"Orange State
Your Device has been unlocked and cant be trusted
Your Device will boot in 5 Seconds".
So after a couple of seconds (around 10-20 sec)
It turns off and immediately on again. I Just can turn it OFF when i hold all 3 Buttons.
Than i try starting it with Volume up + Power / Volume down + Power, But i cant access Recovery or TWRP.
So i should wait til the battery gets low and try it again ?
Like i said, my custom Rom (Evolutionx) and TWRP just worked fine. I dont know man ...
Well since your bootloader is unlocked, try flashing the stock rom again. Look for a tutorial and follow it.
Hi I managed to unbrick my device with this guide, and im back on a stock rom
Unbrick
i ran following commands to get to my custom rom:
I run adb reboot bootloader,
add executed following commands.
(Pitch Black recovery 3.1)
- adb reboot bootloader
- fastboot flash recovery recovery.img
-fasboot reboot recovery
It just hang up and booted after a while into the normal system.
But im not able to get to the recovery menu ?
When I restart and hold Volume up + Power, i go in a loop and the phone keeps restarting over and over again.
what have i Fu**ed up ?
Do i need another recovery tool ?
sorry guys, i appreciate your help a lot tho !
EDIT: Is my bootloader unlocked ?
I can access via "adb reboot bootloader" the phone
and on the blackscreen on the phone it is written:
oppo verfiy pass
fastboot_unlock_verify ok
Update:
So i tried some Stuff and i got Red State. No Problem i Unbricked it once again and now im on Stock Android 10.
Now im Trying to enable the bootloader again.
I downloaded the In Depth Test_Realme_6.apk but i keep getting the Error that i should update the system.
So should i update the system ?
I cant find a CURRENT Tutorial to make this work, please help...
If you cant find a tutorial for your version, why not downgrade back to a previous one if possible.