TWRP FOR ALL SM-G318 SERIES( like SM-G318H or SM-G318MZ or SM-G318HZ )
All credit goes here : http://www.phonandroid.com/forum/galaxy-ace-4-neo-sm-g318h-t142379.html
Press THANK Button if it work for u :good:
(IMPORTANT)Before doing anything u need to:
-HAVE EXACT SAME MODEL (SM-G318 Series Line-up Model) and TO BE ROOTED.
The only way to get root is by flashing the Pre-rooted Firmware by Andro-Man: https://forum.xda-developers.com/android/development/pre-rooted-firmwares-samsung-sm-g318hz-t3230844
Warning!
if u have latest stock rom with "ASKS Security"....before doing any root method,pls downgrade to the older version of stock rom.
How to know if u have "ASKS Security" installed ?
-Go to Settings > About Phone > Find "ASKS Security Version"
If dont have it then u are on the old version of stock rom and can do any root method without any problem.
it is because if u do that u will get stuck on Logo when u boot for example "Galaxy V Plus" because i have sm-g318hz device.
i have experience this problem when i try flashing prerooted rom when i have "ASKS Security" installed on my sm-g318hz.
-Have the USB drivers installed on your computer.
-Have all File Requirement given
-Have a charged battery over 70%.
-Make a backup of your personal data.(Optional just incase)
I DONT RESPONSIBLE FOR ANY DAMAGE TO UR PHONE!! DO IT AT UR OWN RISK !!!!
File Requirement :
For Method 1 (via PC):
Odin : http://androidhost.org/wZgTz
TWRP Recovery : https://drive.google.com/file/d/0B-lRrn2nKLf4TW9iWHNaOXI5bjA/view?pref=2&pli=1
For Method 2 (without PC):
RASHR Flash tool: https://www.apk4fun.com/apk/925/?_e_pi_=7,PAGE_ID10,2769102785
TWRP Recovery: https://mega.nz/#!4NJBDbiB!PXQZ9YYfmo7cb-3zV11Eww7y4bXeFgoV7s8Mn8uNcz4
Method 1:
Installing TWRP Recovery (via PC):
1. Turn off your smartphone.
2. Execute the file Odin3_v3.10.06.exe contained in the unzipped folder.
3. Make sure you have only Auto Reboot and F. Reset Time of checked.
4. Select AP then choose twrp.tar file
5. On your smartphone, press and hold down the Volume Down + Home + Power and Volume Up to restart your smartphone into download mode.
6. Connect the smartphone to the computer with the USB cable of origin. The box below ID: COM should be colored.
7. Click Start to begin the installation.
8. Wait for the installation and do not touch anything until u see Green Light *PASS*
9. Wait for the installation and do not touch anything. Your smartphone automatically restart.
10. Turn Phone ur phone back.
11. Press Power button + Press Volume up button + Home Button to boot into recovery. Release ur finger after u see *Samsung Galaxy *
12. Ignore the message and swipe to right on slider given
13. That it now u have TWRP Recovery installed on your phone :fingers-crossed:
Example Picture for Instruction: http://www.hostingpics.net/viewer.php?id=170738212.jpg
Method 2:
Installing TWRP (without PC):
*If Method 1 is not working try this method.
1. Install RASHR Flash tool.
2. Put recovery.img into root External SD Card.
3. After that open the RASHR Flash tool and select Recovery From Storage.
4. Find and select the recovery.img
5. If the dialog appear press Yes and then reboot into recovery.
6. Wait for few second to reboot into recovery and u have TWRP installed
Nice!??? BTW! It's "TEAM" not "TWIN" ?
xAthenax said:
Nice!������ BTW! It's "TEAM" not "TWIN" ��
Click to expand...
Click to collapse
Sorry for that mistake i never notice that
Thanks for trying my project :good:
This is my first post anyway. So what phone model are you using ?
thnks dev for the recovery. any rom for this phone????
Kikaa99 said:
Sorry for that mistake i never notice that
Thanks for trying my project :good:
This is my first post anyway. So what phone model are you using ?
Click to expand...
Click to collapse
SM-G313HZ it's Samsung Galaxy V
---------- Post added at 06:11 AM ---------- Previous post was at 06:07 AM ----------
guvey said:
thnks dev for the recovery. any rom for this phone????
Click to expand...
Click to collapse
What's the model of your phone? I can search it
xAthenax said:
SM-G313HZ it's Samsung Galaxy V
---------- Post added at 06:11 AM ---------- Previous post was at 06:07 AM ----------
What's the model of your phone? I can search it
Click to expand...
Click to collapse
sm-g318ml
For now , they are still no dev working on custom rom for this model (SM-G318 Series) .
i have try some Galaxy V (SM-G313Hz) custom rom but then i got stuck on boot screen .
i know someone that made a Prerooted stock rom for (SM-G318 Series). u can google it or just search the thread in xda.
xAthenax said:
SM-G313HZ it's Samsung Galaxy V
---------- Post added at 06:11 AM ---------- Previous post was at 06:07 AM ----------
What's the model of your phone? I can search it
Click to expand...
Click to collapse
wow i though it only work for SM-G318 Series only ?
this is impossible ??
guvey said:
sm-g318ml
Click to expand...
Click to collapse
Unfortunately I can't find any custom Roms for your phone
it does not mater what phone model we have.if u found custom for that phone like *Cyanogenmod 12 for SM-G318ML* it also can be apply to all SM-G318 phone series like i mention in my top post.
@Kikaa99 i flashed twrp.tar in odin, it said success but when i try to reboot to recovery i only get the stock recovery
can you help
pipyakas said:
@Kikaa99 i flashed twrp.tar in odin, it said success but when i try to reboot to recovery i only get the stock recovery
can you help
Click to expand...
Click to collapse
Did you follow the steps carefully ?
Most people getting this worked....
Did you try any custom recovery before ?
I want you to reflash the recovery again.
Kikaa99 said:
Did you follow the steps carefully ?
Most people getting this worked....
Did you try any custom recovery before ?
I want you to reflash the recovery again.
Click to expand...
Click to collapse
I tried to reflash a couple of times, but it didnt work
Then i flash a pre-rooted firmware, extract the recovery.img and flash it via flashfire, then i got twrp
Now that i got a way to get root + twrp everything is fine but not the way i thought though
pipyakas said:
I tried to reflash a couple of times, but it didnt work
Then i flash a pre-rooted firmware, extract the recovery.img and flash it via flashfire, then i got twrp
Now that i got a way to get root + twrp everything is fine but not the way i thought though
Click to expand...
Click to collapse
Glad to hear that mate
Guys, pls share this post to all SM-G318 User :good:
Sharing is caring
Hi guys! Anyone having troubles with wifi? It just doesn't turn on...model sm-g318
Adlxcrash said:
Hi guys! Anyone having troubles with wifi? It just doesn't turn on...model sm-g318
Click to expand...
Click to collapse
do u having this problem after try this tutorial ?
and what actually ur phone model ?
i mean we have a lot sm-g318 series (like SM-G318HZ OR SM-G318MZ)
Kikaa99 said:
do u having this problem after try this tutorial ?
and what actually ur phone model ?
i mean we have a lot sm-g318 series (like SM-G318HZ OR SM-G318MZ)
Click to expand...
Click to collapse
Thanks but I gave up... I think it must be a hardware problem .... twrp works excellent so.. it may be another thing like wifi module in the board... thanks anyway mate!
Works on SM-G318ML?
Hi I have a question, does it work for the SM-G318ML?
*Sorry my english is very bad xD
NecroMacro said:
Hi I have a question, does it work for the SM-G318ML?
*Sorry my english is very bad xD
Click to expand...
Click to collapse
Root worked for me, so TWRP should work too.
Enviado de meu SM-A9000 usando Tapatalk
I have SM-G318HZ
I follow your instruction in ODIN
but twrp is not installed.
it still gives me the stock recovery.
any idea?
Related
hey guys i’m in big problem..
in previous 1 week i was install custom recovery TWRP for rooting device.. after that my cell get an update just for bugs fixing. when downloading complete i was just click on restart and update now my cell phone get in TWRP recovery and start updating after this my mobile get restart and just stuck on honor logo..
and my developer options is off..
please guys help me..
full new mobile i get this mobile 2 weeks ago just :crying: :crying:
help me:crying:
heartsking35 said:
hey guys i’m in big problem..
in previous 1 week i was install custom recovery TWRP for rooting device.. after that my cell get an update just for bugs fixing. when downloading complete i was just click on restart and update now my cell phone get in TWRP recovery and start updating after this my mobile get restart and just stuck on honor logo..
and my developer options is off..
please guys help me..
full new mobile i get this mobile 2 weeks ago just :crying: :crying:
help me:crying:
Click to expand...
Click to collapse
did you read any of the other threads about updating with TWRP ?
it's hard to help people when they don't tell you anything about their phone.
do you have a KIW-L24 / L22 / L21 or something else ?
did you try and find the correct update and stock recovery for your phone in The 5X File Depot ?
Did you read the how to return to stock so you can take updates ?
I can help you, but you have to post useful information and you have to try and find answers that have already been posted
clsA said:
did you read any of the other threads about updating with TWRP ?
it's hard to help people when they don't tell you anything about their phone.
do you have a KIW-L24 / L22 / L21 or something else ?
did you try and find the correct update and stock recovery for your phone in The 5X File Depot ?
Did you read the how to return to stock so you can take updates ?
I can help you, but you have to post useful information and you have to try and find answers that have already been posted
Click to expand...
Click to collapse
Hey clsA, thought I'd jump this thread as I;m having the same issue, I'm on L21, I downloaded the recovery image for L21 and applied it through fastboot but I don't know what to next, I read the how to return to stock but I am not sure I follow, could you please help? Thank you
Ash_54 said:
Hey clsA, thought I'd jump this thread as I;m having the same issue, I'm on L21, I downloaded the recovery image for L21 and applied it through fastboot but I don't know what to next, I read the how to return to stock but I am not sure I follow, could you please help? Thank you
Click to expand...
Click to collapse
look here and see if it helps
http://forum.xda-developers.com/showthread.php?p=66524182
clsA said:
look here and see if it helps
http://forum.xda-developers.com/showthread.php?p=66524182
Click to expand...
Click to collapse
sorry, should have mentioned, nothing TWRP works, I can get to the bootloader and thats about it, also currently downloading the L21 B130 update from here http://forum.xda-developers.com/honor-5x/development/stock-kiw-l24-l21-t3312684
Ash_54 said:
sorry, should have mentioned, nothing TWRP works, I can get to the bootloader and thats about it, also currently downloading the L21 B130 update from here http://forum.xda-developers.com/honor-5x/development/stock-kiw-l24-l21-t3312684
Click to expand...
Click to collapse
If you flashed stock recovery you no longer have TWRP
to apply the update.app you put it in a folder on your ext_sdcard called dload
then power off the phone and power it on holding volume + and volume - and Power
this will start the flash from the dload folder
---------- Post added at 02:42 PM ---------- Previous post was at 02:38 PM ----------
Arobase40 said:
Ha ha clsA, we're on the same boat !
To all other you guys, when you receive the notification for a security update, YOU HAVE TO FLASH BACK A STOCK RECOVERY if you had TWRP before! ^^
Click to expand...
Click to collapse
It was always the same thing in the HTC forums ...every time an update drops know one remembers to return to stock to take it.
clsA said:
If you flashed stock recovery you no longer have TWRP
to apply the update.app you put it in a folder on your ext_sdcard called dload
then power off the phone and power it on holding volume + and volume - and Power
this will start the flash from the dload folder
---------- Post added at 02:42 PM ---------- Previous post was at 02:38 PM ----------
It was always the same thing in the HTC forums ...every time an update drops know one remembers to return to stock to take it.
Click to expand...
Click to collapse
yea fully my fault lol, first time with an android,
and the first update.app I got seemed corrupt, will do your advice here then try your second method from your getting back to stock rom guide
Ash_54 said:
yea fully my fault lol, first time with an android,
and the first update.app I got seemed corrupt, will do your advice here then try your second method from your getting back to stock rom guide
Click to expand...
Click to collapse
update.app is not corrupt it's encrypted you can't open it without a special tool
you did unzip it first right ?
your other option is to fastboot flash TWRP and this Rom >> http://loadbalancing.modaco.com/download.php?file=customromtemplate-5x-plk21-b130-r3.zip
clsA said:
update.app is not corrupt it's encrypted you can't open it without a special tool
you did unzip it first right ?
your other option is to fastboot flash TWRP and this Rom >> http://loadbalancing.modaco.com/download.php?file=customromtemplate-5x-plk21-b130-r3.zip
Click to expand...
Click to collapse
I did not no, I read a section where you put it in as a zip, may have been my issue, but I have solved it, method 3 from you getting back to stock rom fixed it, Thank you SOOOOO much for your help. was scared for a bit
clsA said:
If you flashed stock recovery you no longer have TWRP
to apply the update.app you put it in a folder on your ext_sdcard called dload
then power off the phone and power it on holding volume + and volume - and Power
this will start the flash from the dload folder
---------- Post added at 02:42 PM ---------- Previous post was at 02:38 PM ----------
It was always the same thing in the HTC forums ...every time an update drops know one remembers to return to stock to take it.
Click to expand...
Click to collapse
@clsA: I'm in the same boat with my L24 Kiwi lol...where do I get the L24 update.app? I have the OTA+update+to+B151.zip from your file repo. Can I put the file as named into the dload folder and reboot into recovery, do I name it update.app or do i need special tools to go into the zip and get the update.app? On a MAC if that helps in your answer.
bex said:
@clsA: I'm in the same boat with my L24 Kiwi lol...where do I get the L24 update.app? I have the OTA+update+to+B151.zip from your file repo. Can I put the file as named into the dload folder and reboot into recovery, do I name it update.app or do i need special tools to go into the zip and get the update.app? On a MAC if that helps in your answer.
Click to expand...
Click to collapse
the full b151 is in the same folder
You extract it.
The OTA doesn't need extracted
Sent from my KIW-L24 using Tapatalk
Can you explain me how did you do to make your 5X work after the update ? I have the same problem and i'm paniqued (sorry for my engish)
suzushima said:
Can you explain me how did you do to make your 5X work after the update ? I have the same problem and i'm paniqued (sorry for my engish)
Click to expand...
Click to collapse
if you have an L21 and the update failed it's difficult to recover
if you have a different model their are other ways to fix your phone
to enter fastboot mode
1. Place the device in fastboot mode:
Turn off the device. (then wait for at least 2 seconds) For a mobile phone, press and hold the volume down and power keys simultaneously for at least 10 seconds (for a tablet, press and hold the volume up and power keys).
2. If the above operations do not switch the device to fastboot mode, please try the following steps:
Turn off the device. (then wait for at least 2 seconds) Then insert the USB cable and press and hold the volume down and power keys simultaneously for at least 10 seconds.
Step 2 worked for me every time
clsA said:
if you have an L21 and the update failed it's difficult to recover
if you have a different model their are other ways to fix your phone
to enter fastboot mode
1. Place the device in fastboot mode:
Turn off the device. (then wait for at least 2 seconds) For a mobile phone, press and hold the volume down and power keys simultaneously for at least 10 seconds (for a tablet, press and hold the volume up and power keys).
2. If the above operations do not switch the device to fastboot mode, please try the following steps:
Turn off the device. (then wait for at least 2 seconds) Then insert the USB cable and press and hold the volume down and power keys simultaneously for at least 10 seconds.
Step 2 worked for me every time
Click to expand...
Click to collapse
@clsA
Thanks for the heads up on extracting the zip to get the dload folder.
I matched the recovery for the B151 with the extracted dload from the B151 firmware and it booted right away.
Thanks for the assist on the forum and the mental note to use stock recovery with stock rom!
clsA bro thanks for helping me but..
i was try to flash recovery but every time get failed..
as i post in 1st question..
MY DEVELOPER OPTIONS IS OFF
USB DEBUGGING ALSO OFF FRP ALSO OFF
i'm in big problem please bro help me..
i'm very thanks full to you
heartsking35 said:
i was try to flash recovery but every time get failed..
as i post in 1st question..
MY DEVELOPER OPTIONS IS OFF
USB DEBUGGING ALSO OFF FRP ALSO OFF
i'm in big problem please bro help me..
i'm very thanks full to you
Click to expand...
Click to collapse
you still have not listed what model your phone is L21/22/24 ?
do you have fastboot installed ?
did you put the recovery.img in the same folder as fastboot ?
is your bootloader unlocked ?
sorry bro
KIWI L21
heartsking35 said:
sorry bro
KIWI L21
Click to expand...
Click to collapse
For clsA to assist you you must answer the other 3 questions he has asked in post #17.
my phone kiwi L21
yes.. fastboot installed..
yes.. bootloader unlocked.
and my recovery changed TWRP to STOCK recovery after update that's why my phone get bricked i think..
thanks for helping and solution
heartsking35 said:
my phone kiwi L21
yes.. fastboot installed..
yes.. bootloader unlocked.
and my recovery changed TWRP to STOCK recovery after update that's why my phone get bricked i think..
thanks for helping and solution
Click to expand...
Click to collapse
clsA has made it simple enough for me in his previous posts in this thread.
Here is what I did....
- I downloaded the B151 stock recovery from clsA's Honor 5x file repo LINK HERE and in his signature and flashed it via fastboot. To enter fastboot look at post #14 in this thread.
- I downloaded also the B151 stock rom [Honor 5X_Firmware_KIW-L24_Android 5.1_EMUI 3.1_C567B151.zip] When you open this zip you will see the dload folder.
I was unable to adb push to the SDCARD so I had to use a card reader to move the dload folder to the root of the SDCARD.
- Once the dload folder is there you can hold down the key combination in step 2 of post #14 and the once stuck at 0% EMUI loading screen will count up the stock firmware install.
Hope it helps you returning to stock
Hello, guys.
Primarily, I'm really sorry for my English - I don't speak very well.
I'm having a serious problem on my MOTO E 2015 LTE.
It have CM 14 installed and I was installing some apps from Google Play and suddently the device stopped working and restarted.
Now the device don't even charge (only on fastboot) - I can't install TWRP ... I've tried but every time when I finish it back to the screen of bootloader unlocked.
I think bootloader is corruped but I can't change it.
I try to install the stock ROM, CM 13 and other the version 5.1 and 6.0 of Android.
I also tried use RSD, mfastboot, fastboot, manual installation code by code to install but dosen't work.
The biggest problem is that I can't install any recovery because alawys come back to bootLOOP infinite.
Sombody can help me?
Thank you very much.
hi bro,
1, the first thing u have to do is put command " fastboot wipe system "
2. after that download cm 13 from its official website and download gapps from gapps.org
3.while its downloading get your recovery from here http://forum.xda-developers.com/moto-e-2015/orig-development/twrp-moto-e-2015-recovery-t3049726 flash using adb and minimal drivers command is " fastboot flash recovery recovery.img make sure ur downloaded recovery is in adb drvicers folder.
4.after that boot into recovery copy both the files ( rom and gapps)
5.flash them
6.first flash rom and then gaaps
7.done i hope it works .
P.S any query ask me
Hey, bro
Master ST said:
hi bro,
1, the first thing u have to do is put command " fastboot wipe system "
2. after that download cm 13 from its official website and download gapps from gapps.org
3.while its downloading get your recovery from here http://forum.xda-developers.com/moto-e-2015/orig-development/twrp-moto-e-2015-recovery-t3049726 flash using adb and minimal drivers command is " fastboot flash recovery recovery.img make sure ur downloaded recovery is in adb drvicers folder.
4.after that boot into recovery copy both the files ( rom and gapps)
5.flash them
6.first flash rom and then gaaps
7.done i hope it works .
P.S any query ask me
Click to expand...
Click to collapse
How are you?
I've tried to do what you say but, frist, the command ''fastboot wipe system'' dosen't exist. It dosen't work out.
Than I put the recovery.img, and it was installed with susessfull but also dosen't work out.
The only thing that I got was the screen ''Unlocked device''.
Do you have other ideas to help me? I really don't know what to do anymore. I've almost everything.
Thank you very much.
hey ! I had the same problem, but here's the solution.
First of all, follow the instructions here:
http://forum.xda-developers.com/mot...e-restore-moto-e-2015-stock-firmware-t3044936
(If the commands dosn't work, remove the "m" of mfastboot in every command.
When it's done, start it, wait 3 minutes (you're gonna have a bootloop) and flash your new rom with the gapps!
The same...
Quentinomino said:
hey ! I had the same problem, but here's the solution.
First of all, follow the instructions here:
http://forum.xda-developers.com/mot...e-restore-moto-e-2015-stock-firmware-t3044936
(If the commands dosn't work, remove the "m" of mfastboot in every command.
When it's done, start it, wait 3 minutes (you're gonna have a bootloop) and flash your new rom with the gapps!
Click to expand...
Click to collapse
Hey, bro! What's up?
I did everything you said and I follow the commands but also didn't work out. :crying:
The system doesn't start and the recovery also not.
You got anything else to help me? =/
Thanks, bro.
bro tell me whether u r able to access bootloader
yNerd said:
Hey, bro! What's up?
I did everything you said and I follow the commands but also didn't work out. :crying:
The system doesn't start and the recovery also not.
You got anything else to help me? =/
Thanks, bro.
Click to expand...
Click to collapse
Is your phone detected by fastboot in bootloader mode. I recommend you to reflash the bootloader of your device.
Positive.
Master ST said:
bro tell me whether u r able to access bootloader
Click to expand...
Click to collapse
Yeah, bro.
I can access bootloader normally.
It may work.
ayush rao said:
Is your phone detected by fastboot in bootloader mode. I recommend you to reflash the bootloader of your device.
Click to expand...
Click to collapse
How can I do this, bro?
I didn't find a way.
Thanks
yNerd said:
How can I do this, bro?
I didn't find a way.
Thanks
Click to expand...
Click to collapse
Which model do u HAVE?
ayush rao said:
Which model do u HAVE?
Click to expand...
Click to collapse
XT514 LTE (2GEN) 4G
Thanks, bro.
yNerd said:
XT514 LTE (2GEN) 4G
Thanks, bro.
Click to expand...
Click to collapse
Hey man,
Download the Stock ROM corresponding to your device. Then connext your device to the PC in bootloader mode. Then extract the ROM is a folder, in the folder open a command prompt there and type fastboot flash bootloader bootloader.img If this doesnt solve your issue then report back and I'll tell u how to flash ur phone to complete Stock.
never never reflash ur bootloader ...................this will brick ur bootloader
---------- Post added at 06:09 AM ---------- Previous post was at 06:08 AM ----------
sorry it will brick ur phone permanently
---------- Post added at 06:10 AM ---------- Previous post was at 06:09 AM ----------
connect ur phone to ur pc open adb drivers and type " adb devices " is it detects then u must flash the recovery try again and again
if everything goes well i will tell what to do nest
.....its ur luck all d best
---------- Post added at 06:11 AM ---------- Previous post was at 06:10 AM ----------
u can even try ayush rao's idea of installing stock rom
Master ST said:
never never reflash ur bootloader ...................this will brick ur bootloader
---------- Post added at 06:09 AM ---------- Previous post was at 06:08 AM ----------
sorry it will brick ur phone permanently
---------- Post added at 06:10 AM ---------- Previous post was at 06:09 AM ----------
connect ur phone to ur pc open adb drivers and type " adb devices " is it detects then u must flash the recovery try again and again
if everything goes well i will tell what to do nest
.....its ur luck all d best
---------- Post added at 06:11 AM ---------- Previous post was at 06:10 AM ----------
u can even try ayush rao's idea of installing stock rom
Click to expand...
Click to collapse
Dude reflashing the bootloader in fastboot definetly doesn't birck ur phone. And when u flash the stock ROM u always reflash the bootloader.
ayush rao said:
Dude reflashing the bootloader in fastboot definetly doesn't birck ur phone. And when u flash the stock ROM u always reflash the bootloader.
Click to expand...
Click to collapse
Hey, bro.
I also tried this but I didn't have successful.
I'm almost giving up. That seems impossible. =/
Hii Guys..
I need the custom TWRP recovery for my LYF water F1S (LS -5201), so that i can root it and install custom ROMs. Developers i request you to do the needful please.
Regards
My phone also f1s.
Did you had any rom-package or recovery.img?
onkarrathee said:
Hii Guys..
I need the custom TWRP recovery for my LYF water F1S (LS -5201), so that i can root it and install custom ROMs. Developers i request you to do the needful please.
Regards
Click to expand...
Click to collapse
Try using this guide
https://forum.xda-developers.com/android/software/guide-how-to-compile-twrp-source-step-t3404024
Guys...i have found a page for the stock rom for LYF water F1s Ls-5201. You can download it from here
I also extracted the stock recovery image from device and here is the link https://drive.google.com/file/d/0BwMCGOjWJuaxY0NSemJ6ZzdNU1U/view?usp=sharing
Also tried the method to make TWRP for LYF water F1_ LS5201 by @suraj-b method.... but not successful yet. For the process i've used twrp recovery of Le 2 x526.
i'm not a developer but it would be my pleasure if whatever i tried, help somebody.
Don't forget to "Hit THANKS..."
onkarrathee said:
Guys...i have found a page for the stock rom for LYF water F1s Ls-5201. You can download them from there http://www.needrom.com/download/lyf-ls-5201/#
I also extracted the stock recovery image from device and here is the link https://drive.google.com/file/d/0BwMCGOjWJuaxY0NSemJ6ZzdNU1U/view?usp=sharing
Also tried the method to make TWRP for LYF water F1_ LS5201 by @suraj-b method.... but not successful yet. For the process i've used stock recovery of Le 2 x526.
i'm not a developer but i would be my pleasure if whatever i tried, help somebody.
Don't forget to "Hit THANKS..."
Click to expand...
Click to collapse
Good job !
How to flash stock firmware to LYF water F1s Ls-5201
Prepare your system-----
1) Install the Qualcomm usb drivers on your system. Download link
2) Check your PC device manager, your phone should be detected in "Qualcomm HS-USB QDloader 9008" mode. It must detect to start the process.
3) Download the stock firmware from here . The software version downloaded with this link is "LS-5201-S10A_LYF_L13EN_200_170124_09-55-13".
4) Extract the downloaded firmware zip to an folder and rename the "IMAGES_FOR_QMSCT" to "firmware".
5) Download & install the QPST tool. Google it you can find it easily.
6) power off your phone & Make sure your device is charged to at least 50%.
7) Run the installed QFIL from installed programmes. Browse in programmer path to the "prog_emmc_firehose_8976_ddr.mbn" file in the folder where firmware is extracted. It will load the firmware & buid will be selected automatically.
8) Click on load xml and select the "rawprogram_unsparse_without_qcn.xml" if you havn't the backup of NV partition of your device.
If you have the backup NV partition of your device than you can select "rawprogram_unsparse.xml" because this will erase your RF Calibration data, IMEI and WiFi/Bluetooth Address etc. and you will have to restore the NV partition after installing the ROM.
I would suggest you to select "rawprogram_unsparse_without_qcn.xml" & keep it simple.
9) Choose the "patch0.xml" after that.
10) Hold the vol+ & vol- key together and plug usb cable to phone to enter into download mode. As you plug in the QPST tool would recognise your device in QDLoader 9008 mode with com port no. and download button will get activated.
11) Click the download button and sit back, it will take some time.
12) "finish dowload" appear, when process got completed and phone will reboot automatically.
13) Disconnect the device from PC one "android screen" appears (usually it takes 5 min. to appear LYF logo screen from android boot screen)
14) If doesn't reboots, there is some problem & get ready for real hard work .
You might have bricked. In this case just press the power button so than it can power ON. If android screen appears you are lucky enough
-----If android screen remains more than 6-8 minute, you are in bootloop. (It useually takes 5 min for LYF logo to appear after android logo)
-----To switch off your device in case of bootloop, press vol+, vol- & power key together for some time. It will switch off.
-----try to flash the firmware again by above process.
I have tested this method on my device and successfully flashed the stock firmware.
Don't forget to "HIT thanks"...!!!
Credit:
@[email protected] for providing the stock firmware
Me: for testing the procedure
Le2 not support MicroSd.
I will try use recovery of oppo R9plus.
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/open?id=0BwVjewgp3fvLbmtxZ21fSUZhOW8
Or download full package with flash tools and supersu.zip [URL="https://drive.google.com/open?id=0BwVjewgp3fvLUnRHS3NGRjlIRTQ]TWRP-OneKeyFlash-supersu-lyf-water-f1s.rar[/URL]
TWRP recovery LYF_LS-5201
Guys... here is the unofficial twrp recovery for LS-5201. Download it here .
Let me know that you suceed..
This is twrp_unofficial_3.1.0.0 ported from Leeco Le2's TWRP recovery using @suraj-b method and if anythong goes wrong on your device download the stock recovery from the thread and flash it from bootloader.
Try on your own risk..!! :fingers-crossed:
Don't forget to HIT "Thnanks" down there
Please share the adb & fastboot files you used for unloacking bootloader and flashing recovery for the noobs. It would help.
keep it up. :good:
zjsss said:
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/file/d/0BwVjewgp3fvLRm9IM0FOcTF1aGc/view?usp=sharing
Click to expand...
Click to collapse
zjsss said:
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/file/d/0BwVjewgp3fvLRm9IM0FOcTF1aGc/view?usp=sharing
Click to expand...
Click to collapse
How to flash it bro...plzzz give us step by step help
---------- Post added at 06:22 PM ---------- Previous post was at 06:14 PM ----------
zjsss said:
Okey.
It works and rooted by supersu system less package.
I shared recovery.img on https://drive.google.com/file/d/0BwVjewgp3fvLRm9IM0FOcTF1aGc/view?usp=sharing
Click to expand...
Click to collapse
If i flash it via fastboot...den can i root it through twrp...
prashant.palange said:
How to flash it bro...plzzz give us step by step help
---------- Post added at 06:22 PM ---------- Previous post was at 06:14 PM ----------
If i flash it via fastboot...den can i root it through twrp...
Click to expand...
Click to collapse
You can download full package and use "OneKeyFlash(LYF-f1s).bat" to flash easier TWRP-OneKeyFlash-supersu-lyf-water-f1s.rar
zjsss said:
You can download full package and use "OneKeyFlash(LYF-f1s).bat" to flash easier TWRP-OneKeyFlash-supersu-lyf-water-f1s.rar
Click to expand...
Click to collapse
Bro but is it proper twrp for f1s...hv u try it
prashant.palange said:
Bro but is it proper twrp for f1s...hv u try it
Click to expand...
Click to collapse
It works well on my phone.
zjsss said:
It works well on my phone.
Click to expand...
Click to collapse
Thnk u soo much to bring us such wonderfull recovery....but bro...i found 2 issue....1 internal storage is showing empty 0mb and 2 der is no option for root like supersu.zip..plzz help me for dat...m i done wrong anything..plzzz help thank u sooo much brother...it doesn't mount internal storage..i tried mound system and data....but data doesn't mount...plzz help..hope u will understand
prashant.palange said:
Thnk u soo much to bring us such wonderfull recovery....but bro...i found 2 issue....1 internal storage is showing empty 0mb and 2 der is no option for root like supersu.zip..plzz help me for dat...m i done wrong anything..plzzz help thank u sooo much brother...it doesn't mount internal storage..i tried mound system and data....but data doesn't mount...plzz help..hope u will understand
Click to expand...
Click to collapse
It's my bad. This img had bugs.I well try to fix it.
You can copy supersu.zip to MircoSD and install it in TWRP rigtht now.
I checked by adb shell root is success.
Very sorry about that.
zjsss said:
It's my bad. This img had bugs.I well try to fix it.
You can copy supersu.zip to MircoSD and install it in TWRP rigtht now.
I checked by adb shell root is success.
Very sorry about that.
Click to expand...
Click to collapse
U r simply genius brother..root works properly.....god bless u ..love u ....:laugh::good:
Just try to make bugless twrp....thnk u in advance....
prashant.palange said:
U r simply genius brother..root works properly.....god bless u ..love u ....:laugh::good:
Just try to make bugless twrp....thnk u in advance....
Click to expand...
Click to collapse
Thx,i found this not a bug.
/data was locked by system.
Into twrp and keep /system read only,
And wipe /data will be ok .
but it will lost all your data in the phone!!!
So backup everything before you do it.
and install supersu .zip again to root.
zjsss said:
Thx,i found this not a bug.
/data was locked by system.
Into twrp and keep /system read only,
And wipe /data will be ok .
but it will lost all your data in the phone!!!
So backup everything before you do it.
and install supersu .zip again to root.
Click to expand...
Click to collapse
So what should i wipe...dalvik, cache, and data dats it..okay....not system...m i right? But data is not mounting den how can i wipe it?
prashant.palange said:
So what should i wipe...dalvik, cache, and data dats it..okay....not system...m i right? But data is not mounting den how can i wipe it?
Click to expand...
Click to collapse
It doesn't matter of wipe /date or wipe 3.
I guess because the phone kernel was rooted.TWRP had right of wipe.
But not so sure that.
Here's Repack of the stock kernel
with dm-verity
SONY RIC off
SperSU EnableD
Working on Z4 Tablet (SGP771 - SGP712) 7.1.1 FW 32.4.A.0.160
DOWNLOAD:
SECOND POST
HOW TO INSTALL :
1. Extract zip file And Flash in Fastboot
2. Install TWRP 3.1.1.0 From Here
3. Then Flash SuperSU.zip From Here
4. Done You Get ROOT
Download section
Changelog :
SGP712 aded
dm-verity is Disabled
Sony RIC is Disabled
SR1-SuperSU-v2.82-SYSTEMMODE.zip Installed
busybox Installed
@IlariJ Now Done
Nimadroid said:
@IlariJ
Click to expand...
Click to collapse
THANKS!! :victory:
May i ask, ... would it be possible for you to make a kernel for the SGP712 - Wifi only version too?
Nimadroid said:
@IlariJ Now Done
Click to expand...
Click to collapse
The device boots fine (no longer infinite bootloop), but once it has powered up, the touchscreen doesn't work.
I have rebooted several times and no help.
In TWRP even the touch works.
Can You fix this? @Nimadroid
IlariJ said:
The device boots fine (no longer infinite bootloop), but once it has powered up, the touchscreen doesn't work.
I have rebooted several times and no help.
In TWRP even the touch works.
Can You fix this? @Nimadroid
Click to expand...
Click to collapse
Flash Stock ftf
Then Flash kernel
If don't change I make another one for you
Mr. Schnabel said:
May i ask, ... would it be possible for you to make a kernel for the SGP712 - Wifi only version too?
Click to expand...
Click to collapse
Provide me the kernel.sin from lastest FTF of your device
And i update this poet for you with your device kernel
@Nimadroid -> Send ya a PM
Nimadroid said:
Flash Stock ftf
Then Flash kernel
If don't change I make another one for you
Click to expand...
Click to collapse
Didn't help.:crying:
@ Mr. Schnabel : Goog idea
@ Nimadroid : Thanks in advance for the SGP772 version
ilarij said:
didn't help.:crying:
Click to expand...
Click to collapse
steevou said:
@ mr. Schnabel : Goog idea
@ nimadroid : Thanks in advance for the sgp772 version
Click to expand...
Click to collapse
post updated new device aded
Nimadroid said:
post updated new device aded
Click to expand...
Click to collapse
Kernel works, thanks
---------- Post added at 07:07 PM ---------- Previous post was at 07:02 PM ----------
SGP712 should use this recovery
https://www.androidfilehost.com/?fid=673368273298956222
Nimadroid said:
post updated new device aded
Click to expand...
Click to collapse
Works, thanks!! :victory:
Upgrade from 7.0
Hi,
quick question:
I am on 7.0 with root and DRM fix comming from here: "[Guide] Nougat with DRM fix, root and TWRP* (SGP771)".
Can I simply flash kernel and TWRP as you described on top of these or do I have to restart with any TFT's on 7.11?
Thanks a lot and best regards
Hi guys, i need your help!
Flashed new tft .160 via Flashtool - check
Flash boot via ADB - check
Flash Twrp via ADB - check
Reboot into recovery - nope nope nope ...
No matter what or how i flash i simply cannot boot into recovery
Tried older Twrp versions, in ADB shell everything is ok, no error, .....
simply don´t know what to do anymore hmmmmm ....
Mr. Schnabel said:
Hi guys, i need your help!
Flashed new tft .160 via Flashtool - check
Flash boot via ADB - check
Flash Twrp via ADB - check
Reboot into recovery - nope nope nope ...
No matter what or how i flash i simply cannot boot into recovery
Tried older Twrp versions, in ADB shell everything is ok, no error, .....
simply don´t know what to do anymore hmmmmm ....
Click to expand...
Click to collapse
If you're using SGP712 you need to flash the proper recovery for that device, the one in OP is for SGP771
This one is the correct one (also linked 3 posts above): https://www.androidfilehost.com/?fid=673368273298956222
Well .. actually OP and your´s in 3rd post and here are all 3 the same
Like said tried these here, from androPlus thread, etc etc ...
Flash via fastboot is working but cannot enter recovery after flashing
Tried to access via Power button, volume button, adb command, ... i dont even have a led signal at power on
Mr. Schnabel said:
Well .. actually OP and your´s in 3rd post and here are all 3 the same
Like said tried these here, from androPlus thread, etc etc ...
Flash via fastboot is working but cannot enter recovery after flashing
Tried to access via Power button, volume button, adb command, ... i dont even have a led signal at power on
Click to expand...
Click to collapse
oh, didn't notice, although I'm pretty sure the one in OP was different
It's booting on my device, but the first time I tried it didn't. I think it booted when I accidentally flashed it on the boot partition instead of the recovery one maybe you can try that.
but before, try hot booting it with:
Code:
fastboot boot ~/Downloads/TWRP-3.1.1-lineageos-karin_windy-20170520.img
Hotboot endet in an Bootloop but flashing recovery to Boot helped! Many many Thanks
€dit: Ok my bad didnt work ....
Hotboot didnt work
Flashing recovery to boot did boot up Twrp - Wiped cache/dalvik, flashed SU, Tablet constanty reboot into TWRP instead of system
Flashed Kernel/Boot to Boot - Tab boots into system but no root
Tried to reboot into recovery - no luck
Android 10 was released today for Galaxy M30 (INS) ,
Here i am posting 2 links
1. For users Who Just Want Stock Rom as it is
2. For Users Who Need rooted stock rom
Steps :
1. Download Zip and Extract
2. For without root users just flashing via odin would be enough
3. Progress if you wana root
4. when your done with setting up your stock rom , go into Software info and activate developer option
5. Turn on OEM unlock and turn off Auto Update System
6. Boot into download mode again
7. open odin and turn off auto reboot
8. Choose the magisk patched zip and extract
9. In Odin under AP choose this tar and flashed
10. now be careful and press volume down and power till your device boots and quickly press volume up and power to boot into recovery mode
11. Wipe Data in stock recovery and reboot and your good to go
So Here's a Grive Link
Both Firmwares need to be extracted and flashed via odin
Unrooted Stock Firmware
Stock Unrooted
Magisk Rooted
Magisk Rooted
XDAevDB Information
ANDROID 10 (ONEUI 2) Stock Firmware and Rooted (M305FDDU3CSL4), ROM for the Samsung Galaxy M30
Contributors
Er. Aditya
ROM OS Version: Android 10
Thanks to ,
Samsung For Firmware
topjohnwu for magisk
reserved just in case
last one
Sorry for ignorance, but... how do I flash the stock unrooted firmware using Odin?
shrmp said:
Sorry for ignorance, but... how do I flash the stock unrooted firmware using Odin?
Click to expand...
Click to collapse
unzip the zip file and there u will find these files
AP_M305FDDU3CSL4_CL17406009_QB27774088_REV00_user_low_ship_meta_RKEY_OS10.tar.md5
BL_M305FDDU3CSL4_CL17406009_QB27774088_REV00_user_low_ship.tar.md5
CP_M305FDDU3CSL1_CP14521597_CL17406009_QB27626610_REV00_user_low_ship.tar.md5
CSC_OMC_ODM_M305FODM3CSL4_CL17406009_QB27774088_REV00_user_low_ship.tar.md5
HOME_CSC_OMC_ODM_M305FODM3CSL4_CL17406009_QB27774088_REV00_user_low_ship.tar.md5
in odin on your right you will find slots to select files
under BL choose BL_M305FDDU3CSL4_CL17406009_QB27774088_REV00_user_low_ship.tar.md5
under AP choose AP_M305FDDU3CSL4_CL17406009_QB27774088_REV00_user_low_ship_meta_RKEY_OS10.tar.md5
under CP choose CP_M305FDDU3CSL1_CP14521597_CL17406009_QB27626610_REV00_user_low_ship.tar.md5
under CSC choose HOME_CSC_OMC_ODM_M305FODM3CSL4_CL17406009_QB27774088_REV00_user_low_ship.tar.md5
make sure ur phone is in download mode and you have your drivers installed
I see, does updating with Odin erase userdata?
---------- Post added at 22:05 ---------- Previous post was at 21:08 ----------
Nevermind, I just tried flashing the update but it does not work with the SM-M305M variant. Back to waiting...
Er. Aditya said:
7. open odin and turn off auto reboot
8. Choose the magisk patched zip and extract
9. In Odin under AP choose this tar and flashed
Click to expand...
Click to collapse
But, in Magisk here, it states:
Reboot to download mode, and flash magisk_patched.tar as AP in Odin, together with the BL, CP and HOME_CSC files. Never flash only an AP file, as Odin can shrink your /data file-system if you do.
Will it be any issues, if we just flash the AP?
Thanks. Flashed Magisk now.
Can i simply falsh it with twrp??
i did everything correctly i'm stuck on Samsung Boot Logo
help
zer0C00L...... said:
i did everything correctly i'm stuck on Samsung Boot Logo
help
Click to expand...
Click to collapse
these steps have been tested alot of times so make sure you dont miss any
Prxtek said:
Can i simply falsh it with twrp??
Click to expand...
Click to collapse
Nope. Plus this phone does not have a TWRP for Q as of now. Moreover, please do not try any TWRP as of now.
Use ODIN only.
---------- Post added at 00:48 ---------- Previous post was at 00:46 ----------
Er. Aditya said:
these steps have been tested alot of times so make sure you dont miss any
Click to expand...
Click to collapse
By any chance you have a list of bloatwares to remove?
vdbhb59 said:
Nope. Plus this phone does not have a TWRP for Q as of now. Moreover, please do not try any TWRP as of now.
Use ODIN only.
---------- Post added at 00:48 ---------- Previous post was at 00:46 ----------
By any chance you have a list of bloatwares to remove?
Click to expand...
Click to collapse
with root you can simply use titanium backuo and remove according to you
Er. Aditya said:
with root you can simply use titanium backuo and remove according to you
Click to expand...
Click to collapse
I tried, and I end up in bootloop, millions of times..
Trouble is, some inbuilt apps are bound with /system, and unable to get through. Moreover, you cannot imagine, I have been into bootloop 11 times since last evening.
So, if a list is present, I would be happy.
Last thing, did you notice, even if you have not logged into google account, it still keeps installing those 5 bloody recommended apps.
vdbhb59 said:
I tried, and I end up in bootloop, millions of times..
Trouble is, some inbuilt apps are bound with /system, and unable to get through. Moreover, you cannot imagine, I have been into bootloop 11 times since last evening.
So, if a list is present, I would be happy.
Last thing, did you notice, even if you have not logged into google account, it still keeps installing those 5 bloody recommended apps.
Click to expand...
Click to collapse
thats google preload stuff but happens just once , i havent faced this issue yet between make a list of apps your removing il take a look
and il work on a debloated version once i get some time
Please upload to one of the alternative sites (google quota block)
Whats the deal with U3, U4, U5 and greater version of bootloaders with Exynos chipset?
I know Samsung has locked bootloaders of USA snapdragon variants, but can all exynos chip-set ones be unlocked?
Or till U2 bootloader can be unlocked and can have root but above U3 cannot be rooted?
It's so confusing, Please someone Help me
Posted for the latest Patched Magisk here: https://forum.xda-developers.com/ga...d-firmware-t4026819/post81336955#post81336955
---------- Post added at 01:52 ---------- Previous post was at 01:52 ----------
For guides: https://forum.xda-developers.com/galaxy-m30/how-to/guide-galaxy-m30-recovery-edl-modes-t4020231
The M305M variant firmware with Android 10 can be found on sammobile. Can it be flashed without regard for the country it was made for or it has to be the same as the original firmware?
kesleyf said:
The M305M variant firmware with Android 10 can be found on sammobile. Can it be flashed without regard for the country it was made for or it has to be the same as the original firmware?
Click to expand...
Click to collapse
Can be used. However ensure you have mounted system.
You may lose data due to that. So ensure to have a backup.