Can anyone please help me for a solution to recover my phone from it's bootloop state, I tried factory reset from stock recovery but it doesn't help, phone still unable to boot to homescreen. Been looking all over the Internet but no luck finding the firmware for ZTE blade S7 t920. I haven't enable the USB debugging on the settings so my pc doesn't detect the phone
Not sure if you manage to sort out you problem yet but you can download a ROM from the ztedevice dot com website and copy the update.zip file to the root directory of your memory card then you do the following:
Forced upgrade (for the phones that cannot be started or the phones that cannot enter standby state)
1) For a powered-off phone, press and hold both the volume key + and power key to enter into Recovery mode.
2) Press the volume key - to select apply update from sdcard, and press the power key to confirm it.
3) Press the volume key - to select the update.zip file, and press the power key to confirm it. The phone completes the upgrade process in about three minutes.
4) On the Upgrade Complete screen, select reboot system now and press the power key to confirm it.
Related
Hi ,
by mistake i deleted all ROM's and i am in recovery mode without any ROM< to install . i tried to connect it to my PC to see if i can put it via USB new ROM but dont see nothing in my computer . any advice what i need to do ?
put the tab to the download mode and use odin. It should work
Boot your Tablet into Download Mode (Press and hold the Power and Volume Down buttons, when turn on Release the Power button but still hold the Volume Down button. then Volume Down Button Navigates Volume Up Button Selects)
Plug your Tablet into your PC and wait for it to connect.
open ODIN3_v1.85.exe
Select the PDA Button and then select the P7510XABKMP_P7510UEKMP_HOME.tar.md5 file (find in sammobile page or google search)
Hit Start and that process should take a couple minutes as it will put your Tablet back to the Factory ROM and Recovery and Kernel Images.
After it finishes it should reboot.
Questions go in the Q&A section
Hey guys,
Iv got a stock US tablet Z, SGP311 on 10.4.1.b.0.109
Iv tried holding power and volume + while booting to get into stock recovery, iv tried tapping Vol+ a few times while booting, iv tried holdin Vol+ for 3 seconds and then hitting power......i cant get this damn thing into recovery!
Can someone help??
Snazarian said:
Hey guys,
Iv got a stock US tablet Z, SGP311 on 10.4.1.b.0.109
Iv tried holding power and volume + while booting to get into stock recovery, iv tried tapping Vol+ a few times while booting, iv tried holdin Vol+ for 3 seconds and then hitting power......i cant get this damn thing into recovery!
Can someone help??
Click to expand...
Click to collapse
There is no Recovery Mode in the XTZ's stock firmware. Here is how to access the available functions of the stock firmware.
1. Power On
Press and hold the POWER button until notification light flashes once, then release POWER button.
2. Power Off
Press and hold the POWER button until menu appears, then select "Power off" and "OK".
3. Restart
Restart device to turn off all running applications and to free up memory.
3.1. Simultaneously press and hold the VOLUME UP and POWER buttons for 10 seconds.
3.2. After the notification light flashes three times, release the buttons.
3.3. The device will power off automatically.
3.4. After the device is powered off, power on the device.
4. Reset
Reset device to its original settings to free up memory.
Don't forget to back up any important data saved on the device!
4.1. Go to Settings > Backup & reset > Factory data reset > Reset tablet.
5. Enable Safe Mode
5.1. Power off the device.
5.2. Press and hold the POWER button until the notification light flashes once.
5.3. Wait until the Xperia™ logotype disappears.
5.4. Press and hold the VOLUME DOWN button.
5.5. The device will restart in Safe Mode.
5.6. To exit Safe Mode, restart the device.
6. Flash Mode
6.1. Power off the device.
6.2. Connect a USB cable to the device.
6.3. Press and hold the VOLUME DOWN button.
6.4. Connect the USB cable to a computer.
6.5. Wait until the notification light flashes red-green once, then release VOLUME DOWN button.
6.6. To exit Flash Mode, disconnect the USB cable.
7. Fastboot Mode.
7.1. Power off the device.
7.2. Connect a USB cable to the device.
7.3. Press and hold the VOLUME UP button.
7.4. Connect the USB cable to a computer.
7.5. Wait until the notification light flashes red then solid blue, then release VOLUME UP button.
7.6. To exit Fastboot Mode, disconnect the USB cable.
8. Service Menu
8.1. Start the Contacts app.
8.2. Go into Settings.
8.3. Touch the blank area at middle bottom of screen for at least five seconds then stop touching screen.
8.4. "Enter service mode" button will be displayed.
8.5. Press the "Enter service mode" button.
8.6. Enter *#*#7378423#*#* (*#*#SERVICE#*#*).
8.7. Service menu will be displayed.
8.Notes.1. Enter *#*#4636#*#* (*#*#INFO#*#*) to display testing information.
8.Notes.2. Enter *#*#73556673#*#* (*#*#SELLMORE#*#*) to toggle Demo Mode activation on/off. WARNING! Activating Demo Mode will delete all personal content (photos, etc.) and settings.
How do you flash CM then ?
Cat McGowan said:
There is no Recovery Mode in the XTZ's stock firmware.
Click to expand...
Click to collapse
Thanks for telling ! I had been looking for this information for a long time.
Apparently, my service info says "bootloader unlock allowed: yes", I wonder if it means that I actually unlocked it or that the device would accept me to do it.
I moreover wonder how one can manage to install CM or root its device without using Recovery Mode. I saw on your signature you rooted your device. May I ask how you did that ?
ducasse.isidore said:
Thanks for telling ! I had been looking for this information for a long time.
Apparently, my service info says "bootloader unlock allowed: yes", I wonder if it means that I actually unlocked it or that the device would accept me to do it.
I moreover wonder how one can manage to install CM or root its device without using Recovery Mode. I saw on your signature you rooted your device. May I ask how you did that ?
Click to expand...
Click to collapse
It means your bootloader CAN BE unlocked.
To install a ROM, such as CM, you first unlock your bootloader, then move the ROM zip to your device. After that, you flash the included kernel from the zip with fastboot. Then, you boot into the included recovery from the kernel and flash the whole ROM.
Sent from my LT26i using Tapatalk
Felimenta97 said:
It means your bootloader CAN BE unlocked.
To install a ROM, such as CM, you first unlock your bootloader, then move the ROM zip to your device. After that, you flash the included kernel from the zip with fastboot. Then, you boot into the included recovery from the kernel and flash the whole ROM.
Sent from my LT26i using Tapatalk
Click to expand...
Click to collapse
I finally found a solution to my problem : I unlocked the device using flashtool-0.9.11's gui procedure, instead of flashtool's fastboot. It succeeded and I can successfully flash anything I want on the device.
I found your rational approach to my problem useful. It helped me isolate a solution. Thanks !
Hi there
I know this is an old thread. But my problem is same. I got this devide called sony experia tablet z lte ntt docomo x variant
My problem is that it got a lock screen and i have forgot the password. So i want to reset it.
But the problem is how do i do that, there isnt a recovery on this thing.
I was playing around with the buttons and i dont know how ,or which combination i pressed the tab booted to a factory reset screen but i wanst sure to reset that time so i exited from that and tablets lock screen appeared.
And now i cant figure out that how to do this again. Please help me
......
Hi there
I know this is an old thread. But my problem is same. I got this devide called sony experia tablet z lte ntt docomo x variant
My problem is that it got a lock screen and i have forgot the password. So i want to reset it.
But the problem is how do i do that, there isnt a recovery on this thing.
I was playing around with the buttons and i dont know how ,or which combination i pressed the tab booted to a factory reset screen but i wanst sure to reset that time so i exited from that and tablets lock screen appeared.
And now i cant figure out that how to do this again. Please help me
......
Press and hold the Power and Volume Down keys for 10 seconds.
The device will reset and restart.
Hi guys,
I just used Download Mode + Odin to push T110.CWM.v6.0.4.8.tar.md5 to my T110 Tablet.
After that I could boot into CWM-based Recovery v6.0.4.8 without issues.
Then I installed the zip file android-armeabi-universal-root-signed.zip
After that I rebooted. And since then I was not able to boot into Android or even Download Mode.
Only Recovery Mode works.
Then I tried to run adb devices from Windows and it reports my device ID number + recovery.
Now I was hoping somebody could help me with some adb commands to get this thing working again.
My initial goal was to root and upgrade from 4.1.2 to 4.2.2.
I would prefer using this lite rom T110UEUANE4.LiteV2.Rooted.Deodexed.June2014.zip instead of the official rom T110XXUANG2_T110OXAANG2_XEO.zip.
But at this point I would not care to much, I just hope it can be fixed again
Many thanks for your help!
How to unbrick your Samsung Galaxy Tab 3 Lite SM-T 110
Things to download:
stock kitkat rom: sammobile.com/firmwares/download/32777/T110XXUANG2_T110OXAANG2_XEO/
Odin: androidhost.org/get/PVAIv
Installation instructions:
1. Extract both zips onto your desktop.
2. Start the odin application.
3. Turn off tablet, and hold -volume button, the home button, and the power button at the same time.
4. Release power button once the tablet turns on but hold the home an the -volume button down.
5. Once transferred to new screen accept warning by pressing the +volume button.
6. Connect your tablet to your computer and wait for Odin to recognize your device.
7. Once recognized, click AP and navigate to the extracted kitkat stock rom MD5 file.
8. Wait about 5 minutes for Odin to check the file.
9. Once odin checks the file make sure to only have Restart and f. reset time checked in the options.
10-1. Click start and wait for installation. to complete.
10-2. If you cannot get to the start button, press tab until you are at the start button and press enter. Start button is at the bottom left.
11. Tablet will restart automatically and you are done.
Quick note: you just learned how to recover from a soft brick.
Hello,
My xt916 bricked for no reason. It is not rooted. Do not respond to any commands such power, power + volume down, power + volume up. The only sign of life is when connected to charger or USB the back home and menu buttons on the bottom light in white.
Searching for solutions I tried to flash stock again with MTK-RSD Lite ver 6.1.6. Used rom XT916_2_26D_2014_A02_MP.mzf
The device appears as connected and enters download mode. The process completes and it shows PASS at the end.
However no sign of life afterwards. Same as before.
Tried to enter recovery mode or fastboot via ADB but when I type adb devices nothing is shown.
beniciof98 said:
Hello,
My xt916 bricked for no reason. It is not rooted. Do not respond to any commands such power, power + volume down, power + volume up. The only sign of life is when connected to charger or USB the back home and menu buttons on the bottom light in white.
Searching for solutions I tried to flash stock again with MTK-RSD Lite ver 6.1.6. Used rom XT916_2_26D_2014_A02_MP.mzf
The device appears as connected and enters download mode. The process completes and it shows PASS at the end.
However no sign of life afterwards. Same as before.
Tried to enter recovery mode or fastboot via ADB but when I type adb devices nothing is shown.
Click to expand...
Click to collapse
Follow these instructions to perform a factory reset on the Razr and Razr D1 D3:
*
With the phone off, remove your SIM card, then press the power button for 1 second while pressing the volume button up
Select the recovery mode by pressing the volume key down until the factory mode (Factory) and press the power button
Wait for the Android appears and press the volume up
Scroll to wipe data / factory reset (wipe data / Factory reset) and press the power button
Scroll to the option Yes - Delete all data (Yes, delete all user data) and press the power button
Select Reboot System Now (Reboot system now) by pressing the power button
Remind client will lose all data stored in the internal memory.
https://motorola-global-es-latam.cu.../prod_answer_detail/a_id/93717/p/30,6720,8632
Sent from my KFFOWI using Tapatalk
sd_shadow said:
Follow these instructions to perform a factory reset on the Razr and Razr D1 D3:
*
With the phone off, remove your SIM card, then press the power button for 1 second while pressing the volume button up
Select the recovery mode by pressing the volume key down until the factory mode (Factory) and press the power button
Wait for the Android appears and press the volume up
Scroll to wipe data / factory reset (wipe data / Factory reset) and press the power button
Scroll to the option Yes - Delete all data (Yes, delete all user data) and press the power button
Select Reboot System Now (Reboot system now) by pressing the power button
Remind client will lose all data stored in the internal memory.
*** edit link removed *****
Sent from my KFFOWI using Tapatalk
Click to expand...
Click to collapse
Thanks for the tip. Already tried this. The phone only lights up when connected by USB or charger. Whether is connected or disconnected (with battery only) it does not respond at all to any key combinations.
The only noticeable thing it is when connected by USB with RSD Lite software when I try power volume down the phone enters download mode and I can flash a rom.
beniciof98 said:
Thanks for the tip. Already tried this. The phone only lights up when connected by USB or charger. Whether is connected or disconnected (with battery only) it does not respond at all to any key combinations.
The only noticeable thing it is when connected by USB with RSD Lite software when I try power volume down the phone enters download mode and I can flash a rom.
Click to expand...
Click to collapse
try house of moto
Moto Drivers, RSD Lite, and other Unbricking Tools
Sent from my KFFOWI using XDA Labs
thanks. gonna give it a shot. I figure out it would not be a very simple solution since I've tried many other solutions until get here.
Hey guys,
I have an odd problem. I have an old Samsung Galaxy S II that has the Home button damaged. I wanted to revive it by installing a Pie 9.0 custom ROM (https://forum.xda-developers.com/galaxy-s2/development-derivatives/9-carbonrom-cr-7-0-t3938111).
I was following the install instructions and initially, because of the damaged Home button, I got into to download mode via ADB to perform the first steps
Code:
0) Install Stock ROM
0.1 After downloading the tools, install the Samsung USB Driver and unzip the file of the rom.
The original rom file is tar.md5
0.2a Boot your phone into Download-mode (Volume down + Power/Standby + Home and hold for 10 seconds).
0.2b Start Odin 3.13.1 in your PC.
0.2c Connect your phone via USB to your PC.
0.2d Press volume up on your phone, Odin should detect your phone.
0.3 In the pit tab on the left side, select the file "i9100_1.5gb-system_6gb-data_512mb-preload_by-the.gangster.pit"
0.4 In AP button, select the tar.md5 file. The Odin app will frozen for a few minutes but do not worry.
After this, select start button. Wait terminate, do not pull the cable
0.5 The device will restart. A message will appear stating that it is encrypted. Turn off your device and enter recovery mode (Volume up + Power/Standby + Home and hold for 10 seconds). Clear Cache and Dalvik / Cache. Restart.
0.6 A warning will appear in the status bar saying that the partition is corrupted. Format the partition. Verify that the partition succeeded in the device settings.
0.7 Charge the phone and follow the next instructions.
I followed the instructions up to point 0.5 at which I realised that I am not able to enter the recovery mode because of the damaged Home button (I know, FACEPALM....). The system is asking me for a password to unlock the encrypted device's storage. I don't know the password and neither does the developer of the ROM so I am not able to launch the system and turn on the programmers options to access the recovery via ADB.
At this point, I am supposed to format the partition to get rid of this encryption problem, so says the developer.
Is there any way I can force the format via PC? The phone is recognized by Odin.
I am really looking forward to your help.
Cheers,
Chris