Related
Hi guys,
I figured I'll post again here since I think I bricked my phone.... I was trying to install Eugene's Vibrant6.zip and I got stuck on the Vibrant Logo with Samsung at the bottom. I tried to reset with both volume buttons and power button and got to grey battery and nothing else...
What I did prior to this was I formatted system and data on the recovery screen as per some posts here and it would just boot into a loop. Windows won't recognize a device and it just shows grey battery image and it doesn't seem to be charging. Anyone can help me?
EDIT:
Out and in the battery, plugged in to USB and it just loads the battery image and it's all grey color as if fully discharged and just stuck on it. Device is also not found in my system so I can't do any adb commands. If I just reset it without the cable it would just sit on the Samsung boot loop. Anything I can do?
UPDATE: Ok, some good news! I heard the sound as it connected via USB, I can see the 2 drives, but they read as Removable Disk and I can't access them...
adb reboot recovery or download
error: device not found
What if simply format the drives via Windows right click menu? Will that do any good or bad? What are my options here? Any help will be appreciated!
UPDATE: Well... looks like this is pretty much a dead phone.... I right clicked and selected Format in My Computer and it just says There is no disk in Driver F: Insert a disk and try again.
Can I a mount an image somehow via MagicISO? Or is there something simpler that I just can't figure out?
Again, thanks for your help!
Thanks.
Has anyone experienced this or am I the only one?
M5devil said:
Has anyone experienced this or am I the only one?
Click to expand...
Click to collapse
Sorry I have never heard of this or witnessed it while flashing anything to my device. Obviously the battery screen signifies that the phone is off but is in charging mode and hitting the power button will boot the device up. (I'm sure you already know of this). Never heard of it being stuck at that screen after flashing. Hopefully you can get this solved soon. Good luck
M5devil said:
Hi guys,
I figured I'll post again here since I think I bricked my phone.... I was trying to install Eugene's Vibrant6.zip and I got stuck on the Vibrant Logo with Samsung at the bottom. I tried to reset with both volume buttons and power button and got to grey battery and nothing else...
What I did prior to this was I formatted system and data on the recovery screen as per some posts here and it would just boot into a loop. Windows won't recognize a device and it just shows grey battery image and it doesn't seem to be charging. Anyone can help me?
EDIT:
Out and in the battery, plugged in to USB and it just loads the battery image and it's all grey color as if fully discharged and just stuck on it. Device is also not found in my system so I can't do any adb commands. If I just reset it without the cable it would just sit on the Samsung boot loop. Anything I can do?
UPDATE: Ok, some good news! I heard the sound as it connected via USB, I can see the 2 drives, but they read as Removable Disk and I can't access them...
adb reboot recovery or download
error: device not found
What if simply format the drives via Windows right click menu? Will that do any good or bad? What are my options here? Any help will be appreciated!
UPDATE: Well... looks like this is pretty much a dead phone.... I right clicked and selected Format in My Computer and it just says There is no disk in Driver F: Insert a disk and try again.
Can I a mount an image somehow via MagicISO? Or is there something simpler that I just can't figure out?
Again, thanks for your help!
Thanks.
Click to expand...
Click to collapse
Slow down for a second. Your phone is definitely not bricked. Ive been over the edge, and been able to bring my phone back to life.
To clarify, you flashed vibrant6.zip through clockwork mod, and then the phone got stuck on the samsung S? How long did you let it sit there?
It sounds like just your ROM is messed up.
Are you able to "get into recovery"? Holding both volume buttons while you power on the phone, without it being plugged into usb.
Do you have Odin? And have you ever used it?
Its totally frustrating when your phone gets messed up and you don't know what to do.
I flashed the stock ROM via Odin and then wanted to install Vibrant6.zip. For that I entered into a recovery mode via Clockwork and as someone in the other thread advised, I formatted system and also data, don't recall exactly. Then it looped to a standard recovery mode and I just rebooted the phone. This is where it got stuck... Vibrant in the center and Samsung at the bottom of the screen. To test it I left it like that from night till this morning. In the morning I woke up it was on the same boot screen.
Before that at night, after seeing it hand at the boot, I held both volume keys and power, waited for it to reboot, and immediately it showed a circular progress bar, but not moving just highlighted the 12 o'clock bar and second later I see the battery image all in gray and nothing else. It just sits on that grey static image without actually charging it (no green section or flashing dots)
Boot logo only appears if I am trying to reset without the USB cable. On the boot loop I plug in the cable and I hear the USB connecting it, I see the 2 Removable disks, but both inaccessible and adb commands don't recognize the device.
Very weird, as in turned off mode it's not charging at all.. just shows this grey battery image with a circle progress froze on 12 o'clock bar.
That's pretty much it.... I was never able to enter into recovery nor download via the buttons. It would just always reboot into this grey battery screen....
Completely helpless.... I did order a new battery from TMO, maybe the battery is fried and that's why it's not charging and just sits on this stupid static grey battery screen.
ArbitrageMan said:
It sounds like just your ROM is messed up.
Are you able to "get into recovery"? Holding both volume buttons while you power on the phone, without it being plugged into usb.
Do you have Odin? And have you ever used it?
Its totally frustrating when your phone gets messed up and you don't know what to do.
Click to expand...
Click to collapse
Holding both volume keys and releasing power once screen goes blank, only show Vibrant logo again... I have tried this a million times
With USB cable it shows grey battery screen, without the cable just a Vibrant boot loop...
I'm assuming that you have the Samsung drivers installed.
Try the following steps:
Take out the battery and then put it back in but don't turn the phone on.
Plug it via USB.. does anything show up on the screen?
zephiK said:
I'm assuming that you have the Samsung drivers installed.
Try the following steps:
Take out the battery and then put it back in but don't turn the phone on.
Plug it via USB.. does anything show up on the screen?
Click to expand...
Click to collapse
Yes, I have the drivers installed as I was able to locate my device and use adb commands to enter into recovery and download. Also Kies worked.
Doing what you asked simply load the grey battery image and nothing else with a progress bar not spinning. Just sort of hangs on this image and that's all.
Booting without the USB cable loads the Vibrant boot loop. Connecting USB at this boot loop state, would play a sound as if it connected to my windows, but I can only see Removable disks that are inaccessible and adb doesn't find the device...
Very strange.... trying to use the button keys to enter into recovery or download is no use, as that just won't ever happen, even when phone was working fine.
Any other suggestions? I would return the phone for replacement... but I am not sure how it would look with all the files still on the internal disk including root if I am not mistaken... I had only few hours of sleep because of this headache
M5devil said:
Yes, I have the drivers installed as I was able to locate my device and use adb commands to enter into recovery and download. Also Kies worked.
Doing what you asked simply load the grey battery image and nothing else with a progress bar not spinning. Just sort of hangs on this image and that's all.
Booting without the USB cable loads the Vibrant boot loop. Connecting USB at this boot loop state, would play a sound as if it connected to my windows, but I can only see Removable disks that are inaccessible and adb doesn't find the device...
Very strange.... trying to use the button keys to enter into recovery or download is no use, as that just won't ever happen, even when phone was working fine.
Any other suggestions? I would return the phone for replacement... but I am not sure how it would look with all the files still on the internal disk including root if I am not mistaken... I had only few hours of sleep because of this headache
Click to expand...
Click to collapse
Are you sure that you're doing the right things to get to download? I've been in this situation and I wasn't able to get into recovery but I was able to get back into download mode.
I believe if you return it back and they find out it was rooted, they will charge you for it. If not, it'll appear on your bill.
I'm sure that you're doing the wrong things to get into download mode. If something is appearing on your screen it is a soft-brick and you're not bricked.
1. Take out battery, put it back in. (to turn the phone fully off)
2. Don't turn it the phone on!
3. Plug the phone into your PC, do not hit the power button!
4. See if the phone shows anything on the screen (powers on its own when plugged in)
IF the phone screen does 'turn on' after being plugged in without you hitting the power button, so far so good.
5. Now while it's on like this, hold the volume up and volume down buttons.
6. Hold the power button as well as the volume buttons until the screen goes black.
7. As soon as the screen goes black, let go of the power button! But DON'T let go of the volume buttons!
Click to expand...
Click to collapse
A tip to get into download mode is to put the phone HORIZONTALLY (sideways) and it will make it a lot easier.
I am pretty much positive about it. I know a lot of people can easily enter into recovery or download modes, but I know many can't and I am one of them. It would just load the grey battery image instantly as I let go of the power button.
1. Take out battery, put it back in. (to turn the phone fully off) DONE
2. Don't turn it the phone on! DONE
3. Plug the phone into your PC, do not hit the power button! DONE
4. See if the phone shows anything on the screen (powers on its own when plugged in) FIRST THING THAT APPEARS IS A CIRCULAR PROGRESS BAR THAT CHANGES TO A GREY BATTERY IMAGE WITH A BAR IN THE MIDDLE OF IT. STATIC IMAGE, NOTHING ELSE.
IF the phone screen does 'turn on' after being plugged in without you hitting the power button, so far so good.
5. Now while it's on like this, hold the volume up and volume down buttons. DONE
6. Hold the power button as well as the volume buttons until the screen goes black. DONE
7. As soon as the screen goes black, let go of the power button! But DON'T let go of the volume buttons! DONE
THE STUPID GREY COLOR BATTERY IMAGE APPEARS AS BEFORE....
I'm thinking maybe battery is fried and that's why the grey color screen appears and not the usual screen where you see the battery charging...
After reading this thread it's clear that my handset is one of the new ones that have recovery/download modes disabled via the volume+power buttons.
So that pretty much covers it... I hope TMO will not ***** about the files that are on the internal sd that I am unable to access and remove... unless anyone else has any fresh ideals how to gain access to the disk
I think I might have a similar problem.
I accidentally deleted the touchwiz framework so I can't do anything ON the phone. It boots up, and gets me to the lock screen. As soon as I unlock, I am greeted with dozens of unending force closes.
I can get into both download and recovery mode, however, I have not been able to get ADB to recognize the device. I am attempting to push the stock ROM to the internal memory to flash over everything.
I'm not sure what to do to get ADB to work but it's driving me nuts!
Stuck at vibrant? I have a fix
Check out android Dev Section... I figured out how to access download mode or stock recovery mode when you are stuck at the vibrant screen!!!! BACK IN BUSINESS VIBRANT OWNERS!!!
i got the same problem and nothing seems to work
Try this out http://forum.xda-developers.com/showthread.php?t=1103706
Feels like I'm having same issues..
the previous post requires opening the phone and I don't have tools for that..
Here's my issue.
I can't get into Recovery or Download and computer won't see phone to Odin.
I've got drivers installed and AIO Toolbox as well as ADB(which won't work because of computer not seeing phone.
Using the manual option(vol+ vol- power), nothing works.
I've done all the tricks like unplug it then hold vol keys plug it insert battery..
When I do plug in the phone to to even just get a charge in it goes the the battery, but my is is frozen or something. doesn't turn green or have a charging animation. After about a minute or so it was start up and boot loop. I read something about a bad battery? I've got two of them and they seemed fine before..
Before all this I had to Odin and go to stock. I was attempting to get ics back but I was being lazy and trying to do as little as possible..bad idea. I was following slim ics install and flashed cm9 daily, slimics and commons..and now this..
I'm not sure what to do..I usually search around xda or google..10 hours later.. idk..Anyone able to give help please?
:crying:
eduardo_reflex said:
i got the same problem and nothing seems to work
Click to expand...
Click to collapse
... do i even have to say it?
droyd666 said:
Try this out http://forum.xda-developers.com/showthread.php?t=1103706
Click to expand...
Click to collapse
this problem is most likely solved. After 2 years!
mylostlonelysoul said:
Feels like I'm having same issues..
the previous post requires opening the phone and I don't have tools for that..
Here's my issue.
I can't get into Recovery or Download and computer won't see phone to Odin.
I've got drivers installed and AIO Toolbox as well as ADB(which won't work because of computer not seeing phone.
Using the manual option(vol+ vol- power), nothing works.
I've done all the tricks like unplug it then hold vol keys plug it insert battery..
When I do plug in the phone to to even just get a charge in it goes the the battery, but my is is frozen or something. doesn't turn green or have a charging animation. After about a minute or so it was start up and boot loop. I read something about a bad battery? I've got two of them and they seemed fine before..
Before all this I had to Odin and go to stock. I was attempting to get ics back but I was being lazy and trying to do as little as possible..bad idea. I was following slim ics install and flashed cm9 daily, slimics and commons..and now this..
I'm not sure what to do..I usually search around xda or google..10 hours later.. idk..Anyone able to give help please?
:crying:
Click to expand...
Click to collapse
Try asking another question. But I suggest using a USB jig. They usually work. Then odin
Sent from Mount Olympus via Hermes
Did you ever get it fixed man? I literally did the very same to mine a while back and It works like butter as we speak. It is fixable with a mini-usb jig or dongle. You can make your own with about $3 worth of parts from radio shack but I recommend buying one, it will be easier. I for the record made mine simply twisting together the resistors and though it was tough to touch the right pins it did eventually work and get me back into download mode.
Hopefully you already got it fixed though. If not I can help you out.
Hello everyone,
I just tried to put CM 10.1 (pollux RC3) on my Z, but I think I made a mistake: I accidently used a fastboot command which was meant for the xperia z phone, not the tablet (something like "fastboot flash boot boot.img"). Now I probably crashed my tablet, didn't I?
First a red light was visible, after 10mins I did a vol.up+power button reset. Now the red light is gone and so is my tablet. I can't get it recognized on the computer anymore, I can't start up the device, nothing.
Anyone has an idea what to do or am I just screwed?
*Edit*
Got it working again, see link in last post.
No you're not screwed. Download your corresponding system dump (do a search in this XTZ forum) eg. SGP311 (wifi 16gb), or SGP312(wifi32gb) and so on. Download flashtool (do a search too). FLASH THAT SYSTEM DUMP WITH FLASHTOOL (sorry for caps). HTH.
cool, thanks for the quick reply. I guess I was a bit fast on the first try...cool someone can help me out
downloading the dump and flashtool right now, gonna take a while, slow connection right now.
cheers
Aaalright...*still hoping not to be screwed*
If I plugin the usb cable to the computer, holding the volume button down for flash mode, absolutely nothing happens. I tried windows boxes and linux boxes, neither one of them logs anything happening on the usb ports.
Does anyone have a suggestion what to do? The tablet seems dead...the only thing is a single quick LED blink if I do a reset with power button + vol. up. So far I can't get it to do anything else besides that.
*New situation*
I plugged in the USB cable while holding power+vol up. Now I got a constant red led...
Trying this right now: http://forum.xda-developers.com/showthread.php?p=42003603
I'm not one to normally start new threads that already have similar posts but I personally cannot seem to find a solution. So heres my scenario:
I have a Sony Xperia Tablet Z SGP311 that I got right after launch. I flashed a custom rom, yada, yada, you know the deal. However, I flashed back to the stock rom and updated it to the latest sony firmware and was running that for the past month. Everything was going good until BAM, my tablet turns off. I thought it had died since I had been watching a video but I remembered it was at 96% when I started using it so I turned it back on and got the screen of the wrench and screwdriver and it would freeze and bootloop. I then used flashtool to flash back to 10.1.C.0.370 and it worked fine, i got it into flashmode and it flashed properly and the tablet worked for a few hours until BAM, back to the wrench and screwdriver bootloop. SO this time i flashed back to the same firmware and used companion to update it to the latest software and that failed and my tablet fails to boot. Not only that I cannot even get it to go into flash mode and here is what happens with various button combos:
Power Button - nothing
Power + volume up - white flash, then triple white flash
If i do power and volume up until the white flash and then move my finger to volume down the LED turns green but only if plugged in, however it doesn't put it into flashmode like it should.
Green light stays on after unplugging.
Red charge light comes on only after hours of being on the charger.
I've tried booting into flashmode, fastboot, just boot on, nothing works even though the LED's are doing SOMETHING. I havent changed what flasthool i've been using and the drivers were working before. I've tried restarting my computer, using different cables, different USB ports.
I am puzzeled on what i should do and wonder if my tablet is bricked, however, I heard that if the white LED comes on and flashes that something can be done about it, but i have no clue on where to go next.
ANY HELP WOULD BE GREATLY APPRECIATED THANKS!!
Ok, hi guys... yesterday I misinterpreted some instructions before flashing Rajeev's PureX v4.1 rom... was on Niaboc79's ExistenZ Y v2.6.0... so went on, wiped and factory resetted... then, instead of formatting system/data, I formatted data AND system so obviously now it gets stuck at the Sony logo when booting because it has nothing to boot up and the only way to shut it off is with the small red button on the left side until it vibrates, resets then shuts off...
I then told myself I could simply flash a .FTF back from FlashTool, but alas, not this time... ok, I'm on D6503 Z2 with locked bootloader which is not unlockable... and now, when my phone's off and FlashTool asks to connect phone in flash mode the phone doesn't act as it normally would. when plugging usb cable, instead of the original green led, it quickly shows red, then green then nothing and on flashtool we can now see an error which is shown in the screenshot below.
Drivers are installed and I guess the problem now has to do with the bogus leds as they are the same just trying to connect in flash mode out of FlashTool... I Googled and read a lot about it yesterday on XDA and the only potential answer I could find was telling to flash a .ftf whrough FlashTool which was my first bet anyway but now, I really can't think of anything and would please appreciate your assistance about that... I hate to say this but I must admit what I'm requesting now is some help to get me through my own f*** up, please...
Might be a corrupt .ftf , try downloading another one or build your own with xperifirm+flashtool.
You can also try repairing with sony pc companion app...
Thanks for the quick answer... In fact I tested with 4 different ftfs I know are working... and as I said the problem is with the inability of phone to enter flash mode and its wrong leds when connecting to flash mode; not a software issue... I also tried with PCCompanion but it fails at detecting the phone since it freezes at the Sony logo and doesn't boot anything...
EDIT it also doesn't charge when I plug usb or ac. Instead it quickly toggles leds red, green, none one time and stays off... same way as when I try connecting it to flashmode holding vol-...
I've flashed many sony phones that don't boot / bootloop with flashtool and they always come to life again unless there's hardware problems
You phone is beeing detected in flashtool as beeing in flashmode so it's entering the correct mode. As a last resort i would try flashing on another pc/os , i still think it's pc related... are you using any android emulator on the pc? bluestacks / andy or that kind of stuff?
They cause loader.sin errors too... had that happen once on my work computer, uninstalled bluestacks and flashed fine afterwards.
Sorry i can't think of anything else right now...
I don't have another pc, but I reinstalled a pc backup so it is as when I originally set it up... reinstalled flashtool, reinstalled drivers and launched FlashTool to flash a .FTF. It just did the same as before flashes red, flashes green then nothing but the same errot message in FlashTool... but I noticed one thing, everytime I just plug phone to pc, Flashtool states it's in Flash mode as it is not. it was simply plugged in... and I don't use such as BlueStacks... and anyway the phone's leds react wrongly first then the asked action, flashing, cannot be applied hence the error message in FlashTool... thanx for your help...
I'm really used to flashing stuff and I know my mistake now was to format the system partition. From that time, it became impossible to flash any .ftf and the only info, signal I've got is the led quickly displaying red then green led intead of just green then starting to flash, when cable is plugged in, holding VOL-...
Damn formatting the system partition should not hard-brick your phone bro i've done exactly the same mistake on my also unlockable BL Z2 a long time ago, wiped everything and rebooted the phone without flashing the rom xD phone would only show sony logo (can't remember led status) but it flashed normally and came back to life. maybe you got really really unlucky and your bootloader got messed up somehow :| You already did everything i would have done without success, i'm also out of ideas... but xda is full of great minds, maybe someone else can help you better.
You are absolutely right... I had done the same mistake on my xperia T, a while back, and a simple flash from flashtool had taken care of it... I don'T even come to ask for help, usually... when I mess things up, I have always succeeded in bringing the thing back to life... until now...
thanx a lot for your help.
EDIT: Oh, even worse now... when flashtool is done preparing the FTF to be flashed and asks to plug in phone holding VOL-, I tried just plugging the phone WITHOUT holding any button and it did the exact same error I screenshotted earlier, with same red/green/none scheme... So computer really sonsiders phone to be in flashmode from the moment it's plugged in...
No problem, wish i could help more. It does seem like your phone is stuck on fastboot or flashmode. If you just power on the phone and connect it to pc (no flashtool running) does your pc device manager detect your phone? what device does it detect? If you connect in fastboot mode (vol up + plugin usb cable) what do you see in the device manager? Maybe try completely discharging your phone, leave it powered on for a day or so until the battery dies completely, maybe it'll "reset" to normal mode? Just throwing some ideas now, at least we're keeping the thread alive, maybe someone more expert will look at it too
Why you guys quoting every post? Makes it tedious scrolling on mobile.
@rubiicon59 old habits lol xD i edited my posts and removed the quotes, since no one else is participating in the thread they aren't really needed...
ptmaniac said:
No problem, wish i could help more. It does seem like your phone is stuck on fastboot or flashmode. If you just power on the phone and connect it to pc (no flashtool running) does your pc device manager detect your phone? what device does it detect? If you connect in fastboot mode (vol up + plugin usb cable) what do you see in the device manager? Maybe try completely discharging your phone, leave it powered on for a day or so until the battery dies completely, maybe it'll "reset" to normal mode? Just throwing some ideas now, at least we're keeping the thread alive, maybe someone more expert will look at it too
Click to expand...
Click to collapse
first, sorry for the late answer... ok,,, when I only plug usb cable into phone, it is not detected... However, I can boot into fastboot and then it's detected in device manager as in the screenshot below... But, it does flash red just before turning blue for fastboot... just the same quick red flash as when I plug USB in...
ptmaniac said:
No problem, wish i could help more. It does seem like your phone is stuck on fastboot or flashmode. If you just power on the phone and connect it to pc (no flashtool running) does your pc device manager detect your phone? what device does it detect? If you connect in fastboot mode (vol up + plugin usb cable) what do you see in the device manager? Maybe try completely discharging your phone, leave it powered on for a day or so until the battery dies completely, maybe it'll "reset" to normal mode? Just throwing some ideas now, at least we're keeping the thread alive, maybe someone more expert will look at it too
Click to expand...
Click to collapse
first, sorry for the late answer... ok,,, when I only plug usb cable into phone, it is not detected... However, I can boot into fastboot and then it's detected in device manager as in the screenshot below... But, it does flash red just before turning blue for fastboot... just the same quick red flash as when I plug USB in... it also doesn't charge when plugged in... no orange led... was at about 90% when it stopped working...
Just a quick tip- don't use the red button, it is only for emergency and it is annoying to open the flap everytime. Instead, use the Power + Volup and hold for a few seconds.
WOW! reallly can'T say why it didn't work first time, but I tried reinserting sd card and retake it out, started one last time to flash a .ftf and it worked.... Great, now back on my backup... everything working as it should now....
thanx to @BlAckXpeRia for the reminder tip... Red button should only be used when everything else failed to shut the phone down...
and of course, thanks to @ptmaniac for your help all along these stressful last 2 days... THANKS!!!
oh yeah, SOLVED
Nice!! i really really like this phone, i would be very sad if it died on me like that, good to hear you got your phone back
M having same issue without any SD card, what should I do ? :'(
Hello,
I was so enthousiastic about the MM update that I didnt realize I was flashing the Z4 Table MM ftf to the Z5 compact. ****!! Now my phone seems to be dead. No vibrating, no lights no matter what I do.
I try to flash the correct ROM with Flashtool, but it doesn't recognize the device.
In device manager, the phone is not recognized "Unknown USB device, attempt for device descript failed" (if I translate correctly).
Is there something I can do?
Open flashtool. Select the firmware you want. And press on flash. Once flashtool prompts you, ONLY THEN you connect your phone while holding the power down button
Sadman Khan said:
Open flashtool. Select the firmware you want. And press on flash. Once flashtool prompts you, ONLY THEN you connect your phone while holding the power down button
Click to expand...
Click to collapse
Unfortunately it didn't work. I read in some other thread that battery has to die for the memory to reset, then recharge and flash. So I am waiting for this to happen... hope it's working.
Enrico2828 said:
Unfortunately it didn't work. I read in some other thread that battery has to die for the memory to reset, then recharge and flash. So I am waiting for this to happen... hope it's working.
Click to expand...
Click to collapse
If you're stuck on the Sony logo screen hold volume up and power to hard boot, there is no need to let the battery drain.
Download a fresh mm .ftf, load up flash tool and prepare files(exclude nothing), wait for flash mode prompt then plug in device while holding volume down(do not let go until it stays solid). It takes a long time to flash,you'll probably think it's stuck at times.
civicsr2cool said:
If you're stuck on the Sony logo screen hold volume up and power to hard boot, there is no need to let the battery drain.
Download a fresh mm .ftf, load up flash tool and prepare files(exclude nothing), wait for flash mode prompt then plug in device while holding volume down(do not let go until it stays solid). It takes a long time to flash,you'll probably think it's stuck at times.
Click to expand...
Click to collapse
I got back from work and no miracle happened. Phone is still dead. The screen is black. When i put it to charger or pc, no led is blinking. When I do hard reset (with little buttin next to sim tray) nothing happens. When I attempt to reset with power button + volume up nothing happens, no vibration.
I tried repair with Sony Companion, it does not recognize the phone. Windows first recognized the device as some generic, then on second and following attempts reports a malfunctionion USB device.
Have I destroyed my phone??? I never unlocked the bootloader or even unrooted. How could I destroy vital parts of the system? Isn't there some low level something there that still should enable me to flash another rom? How can I get to this part?
I feel a bit devastated now. I actually never realized flashing had this danger (if bootloader locked ...)
Enrico2828 said:
I got back from work and no miracle happened. Phone is still dead. The screen is black. When i put it to charger or pc, no led is blinking. When I do hard reset (with little buttin next to sim tray) nothing happens. When I attempt to reset with power button + volume up nothing happens, no vibration.
I tried repair with Sony Companion, it does not recognize the phone. Windows first recognized the device as some generic, then on second and following attempts reports a malfunctionion USB device.
Have I destroyed my phone??? I never unlocked the bootloader or even unrooted. How could I destroy vital parts of the system? Isn't there some low level something there that still should enable me to flash another rom? How can I get to this part?
I feel a bit devastated now. I actually never realized flashing had this danger (if bootloader locked ...)
Click to expand...
Click to collapse
try reinstalling your drivers also when you connect your phone to the charger do u get a charging light ?
did you try a different USB cable, i saw it hapen that crappy USB cables gives a bad flash, or doesn't recognize the device
If you really don't find any other solution, bring it to the Sony repair center/the shop you bought from and tell that it was updating to Marshmallow but after the restart, the phone was dead.
I highly doubt your phone will work again in the current state you've left it in.
I've flashed a boot.img from another device to see what happens, the phone just vibrates and turns back off. Can easily recover by flashing the correct boot.img, so it looks like yours is damaged at a lower level.
I assume the bootloader tried to update itself with files from the wrong device instead of checking.
Good Luck.
Sent from my E6653 using Tapatalk
Thanks everyone for the support. I didn't have a chance to report back earlier due to work. I want to describe everything as good as possible, so maybe other people having the same problem later on can refer to this thread.
When I put in the charger, no LED is turning on.
I tried a different computer (win7), installed flashtool and then ALL drivers included with flashtool drivers. No help.
I left the charger on for many hours, the previous night I also tried what is referred to as the "rubber trick". Nothing.
I looked at several threads, http://forum.xda-developers.com/showthread.php?t=1849170, http://forum.xda-developers.com/xperia-m2/help/hard-bricked-power-to-flash-mode-t3004020, http://forum.xda-developers.com/xperia-z2/help/help-bricked-z2-t3052671, http://forum.xda-developers.com/xperia-m2/help/dead-m2-recognized-somc-flash-device-t3304758. As far as I can see none of the people who encountered similar symptons have reported back solving it other then sending it to Sony repair.
I contacted Sony support, they asked me to charge it, attempt Sony Companion repair. Of course it doesn't help. So I contact them again tomorrow (indeed telling after MM upgrade it didn't start) and then send it to them.
I just don't understand how this could have been happened, seeing what celderic reports. Is it even related to me flashing the wrong ftf, or could it also happen even likely while flashing the good ftf?
Is flashing ftf's even save? If not, maybe we should warn people more about it. (I always assumed as long as you don't root / unlock bootloader nothing can really go wrong, cause the important parts I am never allowed to touch).
Ironic, I was so impatient for FINALLY getting a working, performing phone, boy, did I prolong my wait. It is really ridiculous Sony could sell us this piece of crap that is slower than my old Blackberry Z10 and make us bear it for so long, and then suddenly they are able to turn it into a superblazer. Should have been like this right from the beginning.
How long did you press the reset button? I had a similar situation with my Z1C a few days ago. Misclicked without realizing it and flashed a wrong rom. Out of frustration and because I was talking to somebody I pressed a paperclip against the reset button for about a minute. At that point the phone did vibrate, went blank again and I could put it in flash mode.
Hm .. I pressed it long, but probably not a minute long. Can't try again though, phone is on its way to repair center.
By the way, someone asked, I used original Sony cable.
Got my phone back working today. Very good support from Sony!! Only took 5 working days. (I'm in the Netherlands)