Supported modells:
Mi 3w,
Mi 4w,
Mi 4LTE (need to 7.1 LTE patch - but developer does not attached this)
This is not my work. I just shared for you from original https://www.flyme.cn/firmwarelist-20.html#7 thread.
Ask*developer "Nic" on the original place if you have any questions.
I am not responsible if you brick your*devices*or other issues.
Please do some research if you have any concerns about features included in this*ROM*before flashing it!
This ROM does NOT COMPATIBLE with old Dual System! You need to merge 2 old system partition to use this ROM.
TWRP 3.2.1.0 recommended!
Recommended:
Working TWRP
Skill in flashing
Flashing method:
Please, before flashing always back up your originalsystem!!!
Clean*install*with TWRP!
Full wipe and factory reset.
Reboot recovery.
After then Install ROM
Reboot, settings.
Go back to TWRP
Install Gapps if you want
Install SU if you want (because this ROM does not contains buil-in root)
Developer original warning message:
注意事项
注意：6.0的用户需要双清后刷入，不可升级刷入！否则会有各种问题！
注意：由于机型"SYSTEM"分区太小，现将部分系统文件挪到DATA分区，如需双清，必须刷ROM前双清！刷ROM后切记不可双清，否则无法开机！望需知！(so, do not install it to Cancro with old dual system)
These are works of chinese developers, so these contains a lot of unuseful chinese*apps.
ROM download link
http://openrom-dl.flyme.cn/7872126/20180402/1522655328982/flyme_MI-4LTE_nic_6.8.3.17R-beta.zip
This is multilanguage hybrid*ROMs*without GAPPS. OpenGapps Arm7.1.2.Pico is compatible.
小米Max全网通版3GB/64GB银色MIUI9中国开发者8.2.1
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my MI3w using Tapatalk
Downloading...
Sent from my MI 4LTE using Tapatalk
Good job...
Sent from my MI 4LTE using Tapatalk
Yepp. Nic is a good Developer.
JulianJenner said:
Supported modells:
Mi 3w,
Mi 4,
Mi 4 Telecom Edition (need to 7.1 telecommunications patch)
This is not my work. I just shared for you from original https://www.flyme.cn/firmwarelist-20.html#7 thread.
Ask*developer "Nic" on the original place if you have any questions.
I am not responsible if you brick your*devices*or other issues.
Please do some research if you have any concerns about features included in this*ROM*before flashing it!
This ROM does NOT COMPATIBLE with old Dual System! You need to merge 2 old system partition to use this ROM.
TWRP 3.2.1.0 recommended!
Recommended:
Working TWRP
Skill in flashing
Flashing method:
Please, before flashing always back up your originalsystem!!!
Clean*install*with TWRP!
Full wipe and factory reset.
Reboot recovery.
After then Install ROM
Reboot, settings.
Go back to TWRP
Install Gapps if you want
Install SU if you want (because this ROM does not contains buil-in root)
Developer original warning message:
注意事项
注意：6.0的用户需要双清后刷入，不可升级刷入！否则会有各种问题！
注意：由于机型"SYSTEM"分区太小，现将部分系统文件挪到DATA分区，如需双清，必须刷ROM前双清！刷ROM后切记不可双清，否则
---------- Post added at 10:25 AM ---------- Previous post was at 10:23 AM ----------
JulianJenner said:
Yepp. Nic is a good Developer.
Click to expand...
Click to collapse
Is it compatible with mi4w?
Click to expand...
Click to collapse
yes. it is. mi3, mi4
rom is stable
all things are working fine :highfive:
good fir daily usage
I like the rom
I hope "Nic" can build ROMs weekly continously...... as he did last year based on Android 6...
小米Max全网通版3GB/64GB银色MIUI9中国开发者8.2.1
after going in additional setting it opens stock setting:laugh:
Thx. I am on AOSP-Extended 5.1 now...so I can't test it.
小米Max全网通版3GB/64GB银色MIUI9中国开发者8.2.1
Mi3w bricked after using this rom for 1day
(clean flashed)
I used fastboot method but didn't work
Anyone plz help me
Cont....
Sorry guys battery issue
ROM awsome
kiran4584 said:
Mi3w bricked after using this rom for 1day
(clean flashed)
I used fastboot method but didn't work
Anyone plz help me
Click to expand...
Click to collapse
Not enough information!
Please specify
Maybe we can help you
What kind of recovery do you use?
What exactly did you do?
We need more information
(Of course, maybe the deterioration of your phone is unrelated to this ROM.)
When update?
I think NIC has stopped developing ROMs for Cancro...
...official site does not contains new ROM/Update.
小米Max全网通版3GB/64GB银色FLYMEOS6全球开发者8.3.27
Nitesh121 said:
JulianJenner said:
Supported modells:
Mi 3w,
Mi 4,
Mi 4 Telecom Edition (need to 7.1 telecommunications patch)
This is not my work. I just shared for you from original https://www.flyme.cn/firmwarelist-20.html#7 thread.
Ask*developer "Nic" on the original place if you have any questions.
I am not responsible if you brick your*devices*or other issues.
Please do some research if you have any concerns about features included in this*ROM*before flashing it!
This ROM does NOT COMPATIBLE with old Dual System! You need to merge 2 old system partition to use this ROM.
TWRP 3.2.1.0 recommended!
Recommended:
Working TWRP
Skill in flashing
Flashing method:
Please, before flashing always back up your originalsystem!!!
Clean*install*with TWRP!
Full wipe and factory reset.
Reboot recovery.
After then Install ROM
Reboot, settings.
Go back to TWRP
Install Gapps if you want
Install SU if you want (because this ROM does not contains buil-in root)
Developer original warning message:
注意事项
注意：6.0的用户需要双清后刷入，不可升级刷入！否则会有各种问题！
注意：由于机型"SYSTEM"分区太小，现将部分系统文件挪到DATA分区，如需双清，必须刷ROM前双清！刷ROM后切记不可双清，否则
---------- Post added at 10:25 AM ---------- Previous post was at 10:23 AM ----------
Is it compatible with mi4w?
Click to expand...
Click to collapse
How to check whether I have dual system ?
And how to merge it back ?
Click to expand...
Click to collapse
Install diskinfo.apk from Play Store.
See size of System. If 1.4-1.5GB, then merged.
小米Max全网通版3GB/64GB银色MIUI9全球开发者8.3.8
NEW 8.3.17 version available
http://openrom-dl.flyme.cn/7872126/20180402/1522655328982/flyme_MI-4LTE_nic_6.8.3.17R-beta.zip
Changelog:
Support: Millet 3w, Xiaomi 4, Xiaomi 4 Telecom (Need to brush 7.1 Telecom patch)
Settings
New: Game Mode (Settings - Auxiliary Mode)
Added: Virtual key switch entry (auxiliary function - display navigation bar)
Fix: Problems with other links
I can't switch between 2G or 3G network also i can't copy or past any text in this rom.hope new updates...
ki
Nope...
Developer stopped to work on Cancro.
小米MIX标准版4GB128GB银色MIUI10中国开发者8.7.25.
Related
THE ROM IS BETA and I do not responsible for failures in the terminal. Try it at your own risk. It is for REDMI NOTE WCDMA (MTK)
Source: http://bbs.ydss.cn Author: Wenwen
All credits go to developer pocarropa
Comment is the first ROM I post and I am not a developer, you've caught this ROM and I have adapted to my taste, but I think it might be interesting test it.
I've tried in my terminal and I have not had any problems but assure their Stability aspects since it is a BETA version.
If you do not know how to reset your REDMI NOTE a bootloop I recommend NOT INSTALL the ROM. (It has not happened but that tells me .....)
* Kernel V6 MIUI 5.1.22 BETA
* Rooteada, SuperSU installed. (If asked to update binary choose METHOD NORMAL)
* Xposed + Gravity
* Multilanguage
* "Rasuradita" -quitadas Chinese apps
* Work both SIMS
* Xperia keyboard
.......
BUGS found:
* Automatic brightness (not implemented)
* Backlight capacitive buttons
* ART mode (although you can switch from options developer, you always work the way DALVIK)
*****INSTALLATION *****
- First of all make a BACKUP INCLUDING NVRAM.
-Download ZIP file on the external SD and restart in RECOVERY mode (I recommend TWRP 2.8.1.0)
-link TWRP 2.8.1.0, credit Cloud:
http://www.mediafire.com/download/pk1155pj1uv2kqi/recovery.img
-Go To ADVANCED and select WIPE DATA, CACHE CACHE DALVIK. Recommended also wipe internal storage (make backup because all the files in the internal memory will be deleted)
-Install ZIP jotikirom
-WIPE And DALVIK CACHE CACHE
Patience, the first startup takes quite
- NO APP DATA RESTORE WITH TITANIUM if you come from a different base to 4.4.2
********************************************
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
DOWNLOAD:
http://www.mediafire.com/download/6qvfgh745d4vdhy/signed_HMNOTE1W_jotikiromV1.zip
.
goxymaster said:
THE ROM IS BETA and I do not responsible for failures in the terminal. Try it at your own risk. It is for REDMI NOTE WCDMA (MTK)
Click to expand...
Click to collapse
Unfortunately Battery consumption is HORRIBLE HIGH.
GPS fast and accurate. I am not think that its able to switch dual SIM 3G, I think the first only can 3G.
Multilanguage, built-in: Gravity Box, Root, Xposed, and minimal GAPPS.
Torch, Camera, Videorecorder works.
Backlight, ART mode, Autobrightness does not works!
One important warning from developer: MAKE FULL (NVRAM and UBOOT TOO!!!) BACKUP BEFORE FLASH THIS ROM, cause it modify NV, so you forget about FULL BACKUP, then You (will) can go wrong!!!
XIAOMI REDMI NOTE HM NOTE1W - JOTIKI 4.4 ROM TESTING
Thanks for feedback. Future update will be better, i hope
I Fished My Phone
How to take backup of NVRAM and UBOOT. pleae explain.
I guess i have lost mine
Restored back to miui stock
When this ROM getting better the people will growth here
---------- Post added at 04:42 AM ---------- Previous post was at 04:40 AM ----------
swapnil0706 said:
How to take backup of NVRAM and UBOOT. pleae explain.
I guess i have lost mine
Restored back to miui stock
Click to expand...
Click to collapse
Flash TWRP and back up with it you will find NVRAM and UBOOT menu options
indhimaga said:
When this ROM getting better the people will growth here
---------- Post added at 04:42 AM ---------- Previous post was at 04:40 AM ----------
Flash TWRP and back up with it you will find NVRAM and UBOOT menu options
Click to expand...
Click to collapse
thanks a a lot mate saw it before .. it just slipped out of my mind
swapnil0706 said:
How to take backup of NVRAM and UBOOT. pleae explain.
I guess i have lost mine
Restored back to miui stock
Click to expand...
Click to collapse
How to restore baclk to stock ROM. I've updated with a buggy .27 MIUI version now not able to downgrade it to MIUI5. Please suggest
dharmuls said:
How to restore baclk to stock ROM. I've updated with a buggy .27 MIUI version now not able to downgrade it to MIUI5. Please suggest
Click to expand...
Click to collapse
Watch this video
https://www.youtube.com/watch?v=zKBbfdawEYg
Connect your phone with battery popped out along with sim and sd card.
And Flash it
For more detail post reply.
Hey i see this rom has been updated isnt it? is this part from this project
http://www.mediafire.com/download/n3se3dbpvr0r0eb/JOTIKIV1_4.zip
Click to expand...
Click to collapse
This is a jotiki rom v1 update 4
1.5 http://www.movilesdualsim.com/tema/actualizada-jotikirom-v1-5-firm-5-2-10-aosp.92703/
Download the latest version of the
rom from here
Version 2.1
https://drive.google.com/file/d/0B43qv7Tx_iJDZlFkcFJ1am92SnM/view?usp=sharing
Rom base updated to latest version
ART is now working (To use it you will have to delete Xposedand Gravity Box)
Xposed and Gravity Box now moved to Data Partition
File manager updated
New tones added for Alarm and notifications
Superuser updated to Kinguser
Gapps Updated
Question
Is this the newest ?
I have installed & mine shows version
Custom Build 4.0
Kernel Version 3.4.67 Tue Mar 17 06:07:45 CST 2015
It no where shows 4.1 & secondly Gravity app fails & settings crashes.
Please help.
How to get sd card work...????
Cos when i insert sd card always get random reboot some thimes get botloop but when i release sd card its back to normal
Sent from my OnePlus using XDA Free mobile app
This is an attempt to make Pixel Experience even better for davinci. The users feedback is totally welcome, we hope to fix all the bugs left by the menphis version.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
What is this?
Pixel Experience is an AOSP/CAF based ROM, with Google apps included and all Pixel goodies (launcher, wallpapers, icons, fonts, bootanimation)
Our mission is to offer the maximum possible stability and security, along with essential and useful features for the proper functioning of the device
Based on Android 9.0
Whats working?
You tell me...
Known issues
You tell me....
Instructions:
- Make a full nandroid backup through TWRP
- Flash required firmware (MIUI Global 10.3.11.0)
- Install The Latest TWRP
- Wipe Stuff / Factory-reset & Clean System partition via TWRP (Wipe -> Format Data)
- Reboot to recovery
- Copy ROM and Magisk for root (optional)
- Install the Rom
- Install Magisk
- Reboot
DON'T FLASH GAPPS, ALREADY INCLUDED
DOWNLOAD
Based on roms/files from: menphis and PIPIPIG233666
Source code: https://github.com/PixelExperience
ROM Developer: jhenrique09
Reserved
I'd like to test this Rom! I'm already on the MIUI Global 10.3.11.0 version and my current ARB value is 1. Can I flash this Rom safely, without encountering ARB issues?
I recently found out I can't even flash the official stable stock rom, because it has an ARB value of 0, which is lower than my current ARB value.
Anyway, if it's safe than I am all in. When will this new version be released?
Medeon said:
I'd like to test this Rom! I'm already on the MIUI Global 10.3.11.0 version and my current ARB value is 1. Can I flash this Rom safely, without encountering ARB issues?
I recently found out I can't even flash the official stable stock rom, because it has an ARB value of 0, which is lower than my current ARB value.
Anyway, if it's safe than I am all in. When will this new version be released?
Click to expand...
Click to collapse
Just delete the arb lines from "flash_all.bat" file and then you could flash the required miui rom
Hope it's fix some bugs, like brightness , fingerprint scanner, and cts false profile in magisk , thanks for the work
Preetam286 said:
Just delete the arb lines from "flash_all.bat" file and then you could flash the required miui rom
Click to expand...
Click to collapse
I am allready on the required MIUI 10.3.11 rom. My question actually is: What will the rollback index of the Pixel experience rom be?
Or does the rollback index only apply to the MIUI firmware?
sergaypoke said:
Hope it's fix some bugs, like brightness , fingerprint scanner, and cts false profile in magisk , thanks for the work
Click to expand...
Click to collapse
Yes, it's the major bugs.
Personally, I have not tested the audio bluetooth, you tested or not?
No I didn't ,just the Samsung frontier 3 and no problems that I found yet
INITIAL RELEASE, ALL FEEDBACK IS WELCOME!
https://mega.nz/#!mhA1wazC!1XzkTUNPBhHE8DLKNoH0BPHKsK0HzlzkEsNbao4cmbQ
Telegram Group
Can't manage to make it boot. I keep ending up in Fastboot Mode.
What I did:
Clean Wipe my device and Install MIUI 10.3.11 (Global - Stable)
[Via TWRP] Factory Reset, wipe System, Format Data
Install ROM and Magisk
Boot
haakufurou said:
Can't manage to make it boot. I keep ending up in Fastboot Mode.
What I did:
Clean Wipe my device and Install MIUI 10.3.11 (Global - Stable)
[Via TWRP] Factory Reset, wipe System, Format Data
Install ROM and Magisk
Boot
Click to expand...
Click to collapse
Same thing here.
maybe you need to flash the permissive zip or vbmeta file?
Verstuurd vanaf mijn Mi 9T met Tapatalk
---------- Post added at 11:34 AM ---------- Previous post was at 11:33 AM ----------
tomorrow i may able to unlock my mi and then i test you rom to. after 7 days waiting.
Verstuurd vanaf mijn Mi 9T met Tapatalk
The OP says: Install The Latest TWRP. I can't tell whether this would be of any influence on flashing this Custom Rom, but it's at least worth to consider it. I know, it's complicated but there are now 4 unofficial versions of twrp recovery for the Mi 9t. The Chinese LR version being the first, following by the russian 4PDA, the Greek version and finally the latest Italian version by @mauronofrio.
---------- Post added at 01:03 PM ---------- Previous post was at 12:27 PM ----------
haakufurou said:
Can't manage to make it boot. I keep ending up in Fastboot Mode.
What I did:
Clean Wipe my device and Install MIUI 10.3.11 (Global - Stable)
[Via TWRP] Factory Reset, wipe System, Format Data
Install ROM and Magisk
Boot
Click to expand...
Click to collapse
Did you already wipe Dalvik / ART cache and Cache?
Did you reboot to recovery between performing a wipe and installing the ROM and Magisk? (sometimes it's in the details)
Medeon said:
The OP says: Install The Latest TWRP. I can't tell whether this would be of any influence on flashing this Custom Rom, but it's at least worth to consider it. I know, it's complicated but there are now 4 unofficial versions of twrp recovery for the Mi 9t. The Chinese LR version being the first, following by the russian 4PDA, the Greek version and finally the latest Italian version by @mauronofrio.
---------- Post added at 01:03 PM ---------- Previous post was at 12:27 PM ----------
Did you already wipe Dalvik / ART cache and Cache?
Did you reboot to recovery between performing a wipe and installing the ROM and Magisk? (sometimes it's in the details)
Click to expand...
Click to collapse
Yup. I tried not using Magisk before first boot as well. Perhaps I should try using a that "latest" TWRP?
Thanks for the perfect rom
im testing this rom without root. i got those errors.
- Bluetooth audio is not working
- 3 camera (48mp) is not working. only 12 Mp cam (middle one) is working.
- Pop-up Camera LED is not working
- Fingerprint is not working clearly
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today
Features:
https://github.com/crdroidandroid/crdroid_features/blob/11.0/README.mkdn
Flashing Instructions:
Pre-installation:
TWRP (Download from here)
FlameGapps (Download from here)
Magisk 20 or newer for root - (Download from here)
First time installation:
Backup your data to PC, OTG flash drive
Flash recovery and boot to recovery
Wipe system, data, cache and format data, then reboot to recovery
Copy ROM, Gapps & Magisk to internal memory then flash them in TWRP in same order
Reboot and enjoy
Update installation:
Boot to recovery and make a backup (not necessary)
Flash updated ROM
Reboot and enjoy
Sources:
ROM:
https://github.com/crdroidandroid
Kernel source:
https://github.com/GZR-Kernels/Optimus_Drunk_Potter
Download:
Rom: https://crdroid.net/potter
Changelog: https://raw.githubusercontent.com/crdroidandroid/android_vendor_crDroidOTA/11.0/changelog_potter.txt
Known isues:
- You tell me
Visit official website @ crDroid.net
crDroid Community Telegram
Donate to help our team pay server costs
XDA:DevDB Information
Crdroid 6 for Moto G5 Plus, ROM for the Moto G5 Plus
Contributors
GtrCraft
Source Code: https://github.com/crdroidandroid
ROM OS Version: Android 11
ROM Kernel: Linux 3.x
ROM Firmware Required: Unlocked Bootloader, Latest TWRP Recovery
Based On: LineageOS
Reserved
Reserved
thx for this im user of poco f1, and moto g5 plus, its run smooth on 2GB RAM (My device give this low memory when buy).
RubenPCA said:
thx for this im user of poco f1, and moto g5 plus, its run smooth on 2GB RAM (My device give this low memory when buy).
Click to expand...
Click to collapse
Please post some screenshots of ROM.
Thanks for the amazing work, rom is very smooth, lots of
customizations, just one thing, not a complaint, just a suggestion, It is possible you could add ringtone per sim card, once again, thank you.
Gapps needed or are they built into the rom?
sunkim50 said:
Gapps needed or are they built into the rom?
Click to expand...
Click to collapse
Maybe read the OP
@GtrCraft if ROM flashed with opengapps nano package then ROM does not boot at all ,get stuck at boot logo.
Will try with pico and report back.
By the way thanks for the crDroid .
---------- Post added at 08:18 PM ---------- Previous post was at 08:11 PM ----------
Aj_$tyle$ said:
@GtrCraft if ROM flashed with opengapps nano package then ROM does not boot at all ,get stuck at boot logo.
Will try with pico and report back.
By the way thanks for the crDroid .
Click to expand...
Click to collapse
@GtrCraft ROM booted successfully with pico gapps.
Loving this ROM, very smooth.
ROM is rock stable (like RR 7 by you) didn't faced a single bug till now.
I am using PX 4.3 Gcam which is working fine.
Battery backup is good ,hell lot of customisation.
One thing I liked is dark mode,which is applied through all the apps like dialer, messages (system apps)etc, previously I was using arrow os 10 and when dark mode was activated it only applied to user apps except system.
Only issue I faced is signal bar fluctuations.
Everything is good, in another words,
This ROM is fiiiyyaah?? !
Encryption not working .. ?
hamxa266 said:
Encryption not working .. ?
Click to expand...
Click to collapse
Will be fixed soon
FM radio working? Thanks!
Nice Rom. Out of all the Roms I tested, this one is the best. Runs buttery smooth without any issues. Encryption and FM radio are not a big deal for me.
I am using this rom with bitgapps. And its works fine.
Please keep providing regular updates. Thankyou
Update Time
You will get a notification for OTA soon or you can download from https://crdroid.net/potter
Changelog:
- Selinux is now Enforcing
- Encryption should work now (untested)
GtrCraft said:
Update Time
You will get a notification for OTA soon or you can download from https://crdroid.net/potter
Changelog:
- Selinux is now Enforcing
- Encryption should work now (untested)
Click to expand...
Click to collapse
Hey dev can you provide incremental update packages?
Aj_$tyle$ said:
Hey dev can you provide incremental update packages?
Click to expand...
Click to collapse
No
Sorry my stupidity and my stupid question, but, what exactly is encryption?
Spoffin suport?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and completely theme-able. You can change just about every aspect of the look and feel.
Code:
Code:
/*
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we will laugh at you.
*
*/
Features:
- Touch Works in all states (No matter about lockscreen there or not)
- Decryption works
- Otg works
- Flash Rom works
- F2FS support
- Fastboot boot command support
Not working:
- Fastbootd
- Adb sideload
- Backup restore and image flash (system-vendor-product)
INSTALLATION:
1. Download the TWRP image file to your PC.
2. Put your device into fastboot.
3. Type the following command to flash the recovery:-
Code:
fastboot flash recovery "name_of_recovery.img"
4. On installation of TWRP , to boot the recovery do:-
Code:
fastboot boot "name_of_recovery.img"
The device will automatically reboot into TWRP, and you will have TWRP as your permanent recovery!
5. Enjoy!
Download:
TWRP By mahajant99
Donation:
PayPal: PayPal.me/mhjn950
UPI: [email protected]
XDA:DevDB Information
TWRP, Tool/Utility for the Xiaomi Poco X3 NFC
Contributors
mahajant99
Source Code: https://github.com/mahajant99/device_xiaomi_surya_twrp
Version Information
Status: Beta
Beta Release Date: 2020-09-26
Created 2020-09-26
Last Updated 2021-01-02
Reserved
Tyvm
Awesome job, haven't tried it yet, but definitely will when I get my X3
What's the diference between this and [RECOVERY][3.4.0-12][surya]TWRP Xiaomi Poco X3?
For now it's the same I presume
bacitoto said:
What's the diference between this and [RECOVERY][3.4.0-12][surya]TWRP Xiaomi Poco X3?
For now it's the same I presume
Click to expand...
Click to collapse
Other recovery has issues TWRP overwrites, this one is previous version but doesnt have this issue tested is working better more user friendly thanks to the developer
This one doesnt freeze the screen after overwrite Nice job bro!!!
piranime said:
Other recovery has issues TWRP overwrites, this one is previous version but doesnt have this issue tested is working better more user friendly thanks to the developer
This one doesnt freeze the screen after overwrite Nice job bro!!!
Click to expand...
Click to collapse
Yes, works good. Flashed Magisk without Problems and tried some reboots without freezing toucscreen!
This one works flawlessly
This TWRP needs some vbmeta file to survive? Format data working? Decryption?
how to use this recovery on this phone but not to be permanent.. I just need temporary twrp to install magisk zip file... Anyone knows?
BlueMan_86 said:
how to use this recovery on this phone but not to be permanent.. I just need temporary twrp to install magisk zip file... Anyone knows?
Click to expand...
Click to collapse
check the installation steps and skip step no. 3 and proceed to step 4 - that will load twrp only virtually...
Good day guys, question, this TWRP can format data, wipe , etc , flash latest magisk like always ?
Is someone using Xiaomi EU with this TWRP and if can provide instructions for flashing or flashing EU via Miflash I´ve read that it's like a fastboot rom/ . TGZ)?... it´s the only rom for now, and stock rom is a monumental mess....
Before on my previous device Davinci I enter TWRP wipe all, flash custom rom based on MIUI , format data and reboot...
Hello Sir, how to unlock the bootloader?
iamlaybhari said:
Hello Sir, how to unlock the bootloader?
Click to expand...
Click to collapse
Any Tutorial on Youtube for Xiaomi devices with MIUI 11, 12 will work , it's the same method for all
Joakin2k said:
This TWRP needs some vbmeta file to survive? Format data working? Decryption?
Click to expand...
Click to collapse
No, just follow the steps mentioned in thread
Joakin2k said:
Good day guys, question, this TWRP can format data, wipe , etc , flash latest magisk like always ?
Is someone using Xiaomi EU with this TWRP and if can provide instructions for flashing or flashing EU via Miflash I´ve read that it's like a fastboot rom/ . TGZ)?... it´s the only rom for now, and stock rom is a monumental mess....
Before on my previous device Davinci I enter TWRP wipe all, flash custom rom based on MIUI , format data and reboot...
Click to expand...
Click to collapse
Yes you can format data wipe etc stuff with this twrp and also magisk can be flashed with it. Rest yes you can flash EU ROM too, download the eu zip from their site.
Thanks OP
Do you need bootloader unlocked to use this flash recovery i am still waiting 7 days for my bootloader unlock?
jutley said:
Do you need bootloader unlocked to use this flash recovery i am still waiting 7 days for my bootloader unlock?
Click to expand...
Click to collapse
Yeah, unlocked bootloader only.
---------- Post added at 03:06 PM ---------- Previous post was at 03:00 PM ----------
Most of the time this recovery will not save the modification I do in Settings (time format, unchecked install twrp app, time zone, unchecked display sleep). After I reboot to recovery, all settings are default.
Any chance to get an custom recovery that supports Android R?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
RevengeOS is an aftermarket firmware based on AOSP. We are dedicated to a beautiful, fast, stable and minimal customized ROM, honesty and communication with our users, and openness with our code, Hope you will enjoy.
Please feel free to look, build, and use our code at RevengeOS GitHub.
Also, we got our Telegram Group to talk about the ROM, share some love, ideas or even have fun with us
If you'd like to join my personal builds and support group you can find it here!
Disclaimer: While we make every effort to test these builds as much as possible, we are not responsible for anything that may happen to your device, family, pets, or perception of reality. We ask that you do your part to know your device and know how to recover from problems before you flash! If you have questions, ask your fellow users or ask us in Telegram Group
Download ROM here for your device!
Ocean
What's Working
- Everything (including selinux enforcing)
BUGS:
- Wifi Display Wifi Display support has been dropped in R
- Video recording Fixed!
- You tell me
Install the ROM
- Make a full wipe
- Flash RevengeOS Package
- Flash gapps [ If you want to ]
- Flash magisk [ If you want to] (Please note you cannot install TWRP and Magisk together at this time)
- Wipe cache! -And at last Reboot!
[First boot will take few minutes! Have patience]
Clean Flash is always recommended!
If you want any bug to be fixed please write here on xda in detail. Give Logcats, mention your device name, mention if any mods and kernels, if used and please be specific about it. By helping us, you are helping yourself too.
->How to take Logcats?
https://goo.gl/UcTM9 and https://goo.gl/J4CSEP
Please consider reading this notice from us!
Hey we need developers
Hi guys, we're posting this message today to talk about RevengeOS, yeah you already know that project so why are we talking about that? Its because I wanna talk about the developers of our project. There are just 3 developers that hard worked everyday for you, with optimization, exclusive UI...
telegra.ph
Like my Work?
Buy me a Beer or Coffee
Donate
Kernel Source :- https://github.com/electimon/
Contributors
@Electimon
@erfanoabdi
@SyberHexen
@Lucchetto
Source Code: https://github.com/RevengeOS
ROM OS Version: Android 11
ROM Kernel: Linux 4.x
Based On: AOSP
Version Information
Status: Stable
Created 2020-10-29
Last Updated 2020-11-21
2020-11-18:
Fixed DRM
Fixed Offline Charging
2020-11-21:
Fixed "vendor.display.config" crashes, manifests as crashing in apps such as Chrome and Amazon
2020-12-15:
Fixed Video Recording
December Patch
2021-01-25:
Fixed Hotspot
January Patch
Which Gapps is recommended?
Or Android 10 Gapps from OpenGapps compatible?
CAKyPA said:
Which Gapps is recommended?
Or Android 10 Gapps from OpenGapps compatible?
Click to expand...
Click to collapse
Open gapps nano unifical ones
will this work on the moto g7 river?
if not is there an ETA for the regular sprint version release of g7?
Will not work
where do i find the gapps?
what are the correct steps to flash the rom. boot twrp, install copy partions, wipe all partions, install rom, and install gapps and isntall magisk and reboot.if that is correct i will attempt.but if not please do tell me how to accomplish the flash correctly .
mrk2815 said:
what are the correct steps to flash the rom. boot twrp, install copy partions, wipe all partions, install rom, and install gapps and isntall magisk and reboot.if that is correct i will attempt.but if not please do tell me how to accomplish the flash correctly .
Click to expand...
Click to collapse
Like any other but if u want root u need certian magisk
This ROM is extremely smooth
Thanks!
yeah man, please update OP with full install info for stock phone ?
One thing I've noticed is if you use the stock gallery app to edit a picture, the app crashes and deletes the picture when saving.
heres a newbee question. i did flash the rom after following all instructions.i am wondering why after a reboot i am now back in recovery in slot b. what do i need to do in order to have the rom boot after the instructions have been completely ffollowed.do i need to change to the active slot from slot b to slot a and then reboot.i don't know so that is why i am asking.
mrk2815 said:
heres a newbee question. i did flash the rom after following all instructions.i am wondering why after a reboot i am now back in recovery in slot b. what do i need to do in order to have the rom boot after the instructions have been completely ffollowed.do i need to change to the active slot from slot b to slot a and then reboot.i don't know so that is why i am asking.
Click to expand...
Click to collapse
Do a -w in fastboot mode
New update,
2020-11-21:
Fixed "vendor.display.config" crashes, manifests as crashing in apps such as Chrome and Amazon
thanks for developing the android 11 rom.at the moment busy with some work but when I have some time will take a look at flashing the rom update .
Electimon said:
New update,
2020-11-21:
Fixed "vendor.display.config" crashes, manifests as crashing in apps such as Chrome and Amazon
Click to expand...
Click to collapse
This is my long waited fix, no more Chrome crash now. Really appreciate this update!
I wish Magisk can live together with TWRP for this rom
can some one explain why people still prefer to have magisk on their devices. dont get it if most apps will break root when it comes to banking and streaming apps that require drm
I accidently flashed this, it worked but without gapps installed, how do I get that now because TWRP cannot be installed
---------- Post added at 01:45 AM ---------- Previous post was at 01:28 AM ----------
Esin8785 said:
I accidently flashed this, it worked but without gapps installed, how do I get that now because TWRP cannot be installed
Click to expand...
Click to collapse
Nm you can indeed put TWRP on the device running 11, I did it through the download command and loaded twrp up that way, That's how I reflashed the phone for Gapps and put a lower version on it as Gapps I can't find for 11 yet
Esin8785 said:
I accidently flashed this, it worked but without gapps installed, how do I get that now because TWRP cannot be installed
---------- Post added at 01:45 AM ---------- Previous post was at 01:28 AM ----------
Nm you can indeed put TWRP on the device running 11, I did it through the download command and loaded twrp up that way, That's how I reflashed the phone for Gapps and put a lower version on it as Gapps I can't find for 11 yet
Click to expand...
Click to collapse
Open gaps bit gaps nickgaps
Esin8785 said:
I accidently flashed this, it worked but without gapps installed, how do I get that now because TWRP cannot be installed
---------- Post added at 01:45 AM ---------- Previous post was at 01:28 AM ----------
Nm you can indeed put TWRP on the device running 11, I did it through the download command and loaded twrp up that way, That's how I reflashed the phone for Gapps and put a lower version on it as Gapps I can't find for 11 yet
Click to expand...
Click to collapse
yes to enter twrp u no need to install, enter bootloader mode then boot twrp using fastboot. after that install latest nikgapps for android R