Related
Hi.
My 9300+ (chinese mtk6577) is dead... I have to updated wrong firmware and my phone will don't turn ON again, when I use the SP Flash Tool appears the message: "Firmware Upgrade could not be executed without PMT. Please "Download" ONLY first to create PMT on the target!
My internal partition is corrupted and i can't create PMT because my phone don't Turn On, but my USB is recognized by windows.
Please Help Me.
rstalker said:
Hi.
My 9300+ (chinese mtk6577) is dead... I have to updated wrong firmware and my phone will don't turn ON again, when I use the SP Flash Tool appears the message: "Firmware Upgrade could not be executed without PMT. Please "Download" ONLY first to create PMT on the target!
My internal partition is corrupted and i can't create PMT because my phone don't Turn On, but my USB is recognized by windows.
Please Help Me.
Click to expand...
Click to collapse
I know this is an old post, but this may help someone. (would have me a month ago)
Hopefully if your USB is seen in Windows you can convince SP Flash Tool to spew/download/write data to your phone while it's in Meta Mode.
I believe the PMT block is created by SP Flash Tool dynamically from scatter file. It's comparing the scatter file with what is sitting at the PMT address on the flash. If these two mismatch, you get the error you mentioned. If you want to force a new PMT that matches your scatter file's layout, you have to do a "Format" in SP Flash Tool. This will get you back to a PMT on flash that matches your scatter file, then SP Flash Tool will be happy and allow you to use Download (write to flash).
What is a PMT? A partition table that holds the addresses to all the other partitions.
syserr said:
I know this is an old post, but this may help someone. (would have me a month ago)
Hopefully if your USB is seen in Windows you can convince SP Flash Tool to spew/download/write data to your phone while it's in Meta Mode.
I believe the PMT block is created by SP Flash Tool dynamically from scatter file. It's comparing the scatter file with what is sitting at the PMT address on the flash. If these two mismatch, you get the error you mentioned. If you want to force a new PMT that matches your scatter file's layout, you have to do a "Format" in SP Flash Tool. This will get you back to a PMT on flash that matches your scatter file, then SP Flash Tool will be happy and allow you to use Download (write to flash).
What is a PMT? A partition table that holds the addresses to all the other partitions.
Click to expand...
Click to collapse
THANK YOU! :highfive::highfive::highfive::highfive::highfive::highfive:
LOVE YOU MAN
PMT Corrupted & Format-all done
I faced the same error.......my PMT got corrupted (possibly due to an earlier attempt to re-size (system / data) partition using Swiftbootloader)...... & un-fortunately, I clicked on Format in SP Flash Tool as well.
Now all is gone.... phone doesn't switch on.........
Please guide...... to bring the bricked handset (Spice Mi-350n) to life again. I have backups..... but that relate to different scatter file (PMT) perhaps........ do I need to search & learn webos & acmeinstaller kind of things now?
spandrd said:
I faced the same error.......my PMT got corrupted (possibly due to an earlier attempt to re-size (system / data) partition using Swiftbootloader)...... & un-fortunately, I clicked on Format in SP Flash Tool as well.
Now all is gone.... phone doesn't switch on.........
Please guide...... to bring the bricked handset (Spice Mi-350n) to life again. I have backups..... but that relate to different scatter file (PMT) perhaps........ do I need to search & learn webos & acmeinstaller kind of things now?
Click to expand...
Click to collapse
Hi spandrd,
did u manage to resolve this problem. I am also facing this problem after attempting to re-size the partition using meteos mtk6589 rom edit apk .... Although my phone is still working properly without any issue, i am unable to root or install CWM by any means (tried mtk mobileuncle tools, tried spflash tool) but not working. Can you guide me how to root and install cwm as i am unable to revert to my old backup w/o cwm.
spandrd said:
I faced the same error.......my PMT got corrupted (possibly due to an earlier attempt to re-size (system / data) partition using Swiftbootloader)...... & un-fortunately, I clicked on Format in SP Flash Tool as well.
Now all is gone.... phone doesn't switch on.........
Please guide...... to bring the bricked handset (Spice Mi-350n) to life again. I have backups..... but that relate to different scatter file (PMT) perhaps........ do I need to search & learn webos & acmeinstaller kind of things now?
Click to expand...
Click to collapse
HNaseer said:
Hi spandrd,
did u manage to resolve this problem. I am also facing this problem after attempting to re-size the partition using meteos mtk6589 rom edit apk .... Although my phone is still working properly without any issue, i am unable to root or install CWM by any means (tried mtk mobileuncle tools, tried spflash tool) but not working. Can you guide me how to root and install cwm as i am unable to revert to my old backup w/o cwm.
Click to expand...
Click to collapse
The best way to restore your phone was already answered in the previous post, that is to FORMAT your device and subsequently flash the official firmware.
syserr said:
I know this is an old post, but this may help someone. (would have me a month ago)
Hopefully if your USB is seen in Windows you can convince SP Flash Tool to spew/download/write data to your phone while it's in Meta Mode.
I believe the PMT block is created by SP Flash Tool dynamically from scatter file. It's comparing the scatter file with what is sitting at the PMT address on the flash. If these two mismatch, you get the error you mentioned. If you want to force a new PMT that matches your scatter file's layout, you have to do a "Format" in SP Flash Tool. This will get you back to a PMT on flash that matches your scatter file, then SP Flash Tool will be happy and allow you to use Download (write to flash).
What is a PMT? A partition table that holds the addresses to all the other partitions.
Click to expand...
Click to collapse
iZLeeP said:
The best way to restore your phone was already answered in the previous post, that is to FORMAT your device and subsequently flash the official firmware.
Click to expand...
Click to collapse
Hi iZLeeP
Thanks for the quick reply. I dont have any official rom. The only backup i have is using the CWM backup of the official rom before applying a custom LG rom. If it is possible, how can i utilize the CWM backup of the official rom to revert back please ? I can see boot.img and recovery.img files in cwm backup; can i utilize them somehow to revert back ? Please help. Thanks.
HNaseer said:
Hi iZLeeP
Thanks for the quick reply. I dont have any official rom. The only backup i have is using the CWM backup of the official rom before applying a custom LG rom. If it is possible, how can i utilize the CWM backup of the official rom to revert back please ? I can see boot.img and recovery.img files in cwm backup; can i utilize them somehow to revert back ? Please help. Thanks.
Click to expand...
Click to collapse
Let me remind people, the first order of business must be to have a full firmware backup from the phone manufacturer or thru MTK Droid Root & Tools. Reading that you tried to resize your system & data partition, your cwm backup should not be affected by it. Try restoring to default the partition sizes using the app/script you used to resize. It should have that function. Then flash custom recovery and root and see if it works.
phone booting to main-screen or not?
hi HNaseer....
As replied by @syserr & @iZLeeP .............you can try to "Format-All / Format-All except bootloader" type of thing PROVIDED THAT YOU HAVE COMPLETE BACKUP OF RELEVANT PARTITIONS (till Cache and / or till FAT partition length) using SP Flash Tool........ & MTK Droid Tool......... PLUS, YOU WILL NEED IMEI BACKUP (IMEI No.) in such case if you want to restore.
SP Flash Tool needs Scatter File......... (obtainable thru MTK Droid Tool) & can help in backup of various partitions even if phone not turning on. BUT IMEI backup would be good........ IF YOU ARE ABLE TO BOOT / reach main screen after boot animation.
Rest of the details can be first read / understood from my MT6589 chipset type handset link from @Atrvscet : http://forum.xda-developers.com/showthread.php?t=2514419
Or, better search exact thread on xda / elsewhere to get stock / custom rom & flashing etc.
Lastly, if you are able to boot in recovery, best thing should be to flash / force flash original cwm backup from recovery.
HNaseer said:
Hi spandrd,
did u manage to resolve this problem. I am also facing this problem after attempting to re-size the partition using meteos mtk6589 rom edit apk .... Although my phone is still working properly without any issue, i am unable to root or install CWM by any means (tried mtk mobileuncle tools, tried spflash tool) but not working. Can you guide me how to root and install cwm as i am unable to revert to my old backup w/o cwm.
Click to expand...
Click to collapse
spandrd said:
hi HNaseer....
As replied by @syserr & @iZLeeP .............you can try to "Format-All / Format-All except bootloader" type of thing PROVIDED THAT YOU HAVE COMPLETE BACKUP OF RELEVANT PARTITIONS (till Cache and / or till FAT partition length) using SP Flash Tool........ & MTK Droid Tool......... PLUS, YOU WILL NEED IMEI BACKUP (IMEI No.) in such case if you want to restore.
SP Flash Tool needs Scatter File......... (obtainable thru MTK Droid Tool) & can help in backup of various partitions even if phone not turning on. BUT IMEI backup would be good........ IF YOU ARE ABLE TO BOOT / reach main screen after boot animation.
Rest of the details can be first read / understood from my MT6589 chipset type handset link from @Atrvscet : http://forum.xda-developers.com/showthread.php?t=2514419
Or, better search exact thread on xda / elsewhere to get stock / custom rom & flashing etc.
Lastly, if you are able to boot in recovery, best thing should be to flash / force flash original cwm backup from recovery.
Click to expand...
Click to collapse
HNaseer.... I agree with everything spandrd just said. I'd like to stress though, getting a backup of your NVRAM partition is much better than having MTKDT copy your /data/nvram. So if you have a choice, backup the NVRAM partition with SPFT or if MTKDT has that option use it. (I've rarely used MTKDT as I found aspects confusing)
Incredible.
Thank you so much. HAd almost given up hope...
How to connect mtk6582device (spice dream uno) in meta mode
Plz help me out guys ??????
I have a similar issue with my Unite 2 phone. I tried the format option too but I am getting STORAGE_ERROR
[Storage Error] The load and the target are inconsistent!
A Hint message is also there :
The load to be downloaded is for EMMC.
The Target storage is .
Please select a correct load according to the storage.
Please help me in resolving this issue. My phone model is Micromac unite 2 A106 8GB model.
syserr said:
HNaseer.... I agree with everything spandrd just said. I'd like to stress though, getting a backup of your NVRAM partition is much better than having MTKDT copy your /data/nvram. So if you have a choice, backup the NVRAM partition with SPFT or if MTKDT has that option use it. (I've rarely used MTKDT as I found aspects confusing)
Click to expand...
Click to collapse
hello guys
how can i format my device Blu studio energy 2 with sp flash toolmy phone is dead after i do the format and i dont have firmware back up
thank you
---------- Post added at 01:24 AM ---------- Previous post was at 12:26 AM ----------
hello guys
how can i format my device Blu studio energy 2 with sp flash tool my phone is dead after i do the format and i dont have firmware back up
thank you
Omarod said:
hello guys
how can i format my device Blu studio energy 2 with sp flash toolmy phone is dead after i do the format and i dont have firmware back up
thank you
Not sure what you are expecting to do with a FORMAT. If you had a good backup of your NVRAM partition, then what you would need is a SCATTER file and ROM files, you could FORMAT then DOWNLOAD the ROM files and your NVRAM file to your device with SPFT. But since you don't have your NVRAM partition, you don't have an easy path. FYI, I don't know new devices... there could be more complication than MT6577/75.
Click to expand...
Click to collapse
syserr said:
Omarod said:
hello guys
how can i format my device Blu studio energy 2 with sp flash toolmy phone is dead after i do the format and i dont have firmware back up
thank you
Not sure what you are expecting to do with a FORMAT. If you had a good backup of your NVRAM partition, then what you would need is a SCATTER file and ROM files, you could FORMAT then DOWNLOAD the ROM files and your NVRAM file to your device with SPFT. But since you don't have your NVRAM partition, you don't have an easy path. FYI, I don't know new devices... there could be more complication than MT6577/75.
Click to expand...
Click to collapse
Thank you for reply
Where do i find the scatter file and the ROM for my blu studio energy 2 MT6735 chepset please
Thank you again
Click to expand...
Click to collapse
Omarod said:
syserr said:
Thank you for reply
Where do i find the scatter file and the ROM for my blu studio energy 2 MT6735 chepset please
Thank you again
Click to expand...
Click to collapse
Try google, or search xda, or needrom.com...
This may or may not help you. If I were you I would use SPFT right now to try to backup your NVRAM partition if it's not too late. Your FORMAT may have wiped the NVRAM partition already. If it has wiped it, your only good path is to find someone willing to give you their NVRAM partition. Then somehow insert your own IMEI and WIFI MAC in and pray.
Click to expand...
Click to collapse
Could you tell me step by step what can I do coz I'm new in sp flash tool and. Mtk droid root and flash tool
Thank you so much
First find proper ROM on www.needrom.com
Hello Guys
still waiting for help please
Blu Studio Energy 2 -Backup file- firmware Please
Hey all.
Easy question I hope! I've been following the guide to unbrick MTK devices, and have managed to get an original factory ROM to flash to the phone, green tick in SP Flash Tools. However, the phone still won't power on at all, save for the light if plugged into usb.
The ROM I've been using is an original factory rom named "ONE-TOUCH-4015X_POP_C1_FULL_STOCK_BACKUP" which is readily available online. I'm not sure what I did to brick it in the first place, but it was within SP flashtool. I May have formatted accidentally.
If someone coudl help I'll try to provide all logs or files requested but please tell me where these could be found as I'm not that good with flash tool.
To confirm the phone won't boot into any mode, recovery is dead, fastboot is dead....
same problem hope somone help us
also share ur backup please
darkglobe87 said:
Hey all.
Easy question I hope! I've been following the guide to unbrick MTK devices, and have managed to get an original factory ROM to flash to the phone, green tick in SP Flash Tools. However, the phone still won't power on at all, save for the light if plugged into usb.
The ROM I've been using is an original factory rom named "ONE-TOUCH-4015X_POP_C1_FULL_STOCK_BACKUP" which is readily available online. I'm not sure what I did to brick it in the first place, but it was within SP flashtool. I May have formatted accidentally.
If someone coudl help I'll try to provide all logs or files requested but please tell me where these could be found as I'm not that good with flash tool.
To confirm the phone won't boot into any mode, recovery is dead, fastboot is dead....
Click to expand...
Click to collapse
Did you ever get the above rom to work? If so what did you do? Or did you find another method to unbrick the phone? Thanks.
Managed to unbrick my 4015 using Mobile Upgrade S 4.3.0 from the Alcatel Website.
http://www.alcatelonetouch.com/global-en/support/download/one_touch_idolx.html
Very simple to use, just install and follow instructions.
darren1 said:
Managed to unbrick my 4015 using Mobile Upgrade S 4.3.0 from the Alcatel Website.
http://www.alcatelonetouch.com/global-en/support/download/one_touch_idolx.html
Very simple to use, just install and follow instructions.
Click to expand...
Click to collapse
no work this version. yes 4015 but no 4015x
Sorry I should have put my phone is a 4015X not 4015. The application does say 4015 which I selected and all went well.
my 4015x no update, it not load, only work flash mode connected to pc and no work mobile upgrade.
4015X Partitions
the 4015x has a different set of partitions to the older (dual sim) 4015
i have a modded rom (kitkat), a modded stock recovery (as stock is also wrong, wont mount data) and a modded cwmrecovery.
i will be posting these soon
i will create a new post for the 4015x version
and will also be asking for other versions of the 4015 users to post me there partition trees and i will repack some recoverys and some roms for you all
note: there are 6 versions that i have seen and they may all have diff tables
hope these will help the pop c1 community
recoverys and rom
Stock Recovery (Fixed)
https://drive.google.com/file/d/0B4ZKFXlQiHioVUExRW1sZkdzSFk/view?usp=sharing
CWMRecovery (Fixed)
https://drive.google.com/file/d/0B4ZKFXlQiHioUTJqOTMtbUNPTEU/view?usp=sharing
kitkat-cm11-modROM.zip (Fixed)
https://drive.google.com/file/d/0B4ZKFXlQiHioUUI3V2Jsd0lTN1k/view?usp=sharing
(I am currently using this rom my self and all seems to be good except vibration, it also thinks its a dual sim but not causing a probb)
Hello!
This thread is quite old but near my case.
I have an Alcatel Pop C1 4015X (cpu MTK6572M) that can't start at all (only the power LED is ON).
I have a backup of this device made with "SP Flash Tool V5.1532.00" but I've error "not enough space" when
I try to restore it.
Same error when I try to restore just one file.
For example, I've tried to restore only the "Stock Recovery" you give above.
I do this:
- I start Flash_Tool v5.1532.00
- I open scatter file from my backup done with the same tool
- I unselect all pieces of the backup except "Recovery" and I browse to the "Stock Recovery" file I've dl
from this thread.
I've got this error : "not enough storage space (1011)"
What could be the problem ?
I makes me totally crazy !
By advance, thanks for your help.
Regards,
Freeman.
Fr33M4n! said:
Hello!
This thread is quite old but near my case.
I have an Alcatel Pop C1 4015X (cpu MTK6572M) that can't start at all (only the power LED is ON).
I have a backup of this device made with "SP Flash Tool V5.1532.00" but I've error "not enough space" when
I try to restore it.
Same error when I try to restore just one file.
For example, I've tried to restore only the "Stock Recovery" you give above.
I do this:
- I start Flash_Tool v5.1532.00
- I open scatter file from my backup done with the same tool
- I unselect all pieces of the backup except "Recovery" and I browse to the "Stock Recovery" file I've dl
from this thread.
I've got this error : "not enough storage space (1011)"
What could be the problem ?
I makes me totally crazy !
By advance, thanks for your help.
Regards,
Freeman.
Click to expand...
Click to collapse
What i did was i used SPFT to flash a backup i found online. Can't post links, just google "ot 4015X Original SPFT ROM", what i used was the algerian rom. Then i flashed the EE stock rom. My own backup didn't flash back correctly either, that's why i used that one i fould online.
4015X unbricked !
Hello,
I found a similar solution here (replace * with . to get a correct http link):
forum*gsmhosting*com/vbb/f317/ot-4015x-firmware-arabic-bulgaria-africa-kenya-1946694/index2.html
It took me hours to find good stock ROMs (bulgarian & arabian then french via OTU) !
You'll have to "play" with pro_info and scatter file...
Good luck to all to unbrick your 4015x !
Regards,
Freeman.
how to partition system storage space of onetouch pop c1?
hi
so i have a Lenovo K8 plus 3 GB ram variant. Let me explain what happened first.
I unlocked my device's bootloader to flash the patched boot image for magisk root, then this orange state sign started showing up eerytime i booted up. then when the latest update rolled out in march, i decided to relock the bootloader and then update my device. did it and then a red state sign showing up accompanied by bootloop (it said something like rollback kernel too). so I formatted the whole thing via sp flash tool and downloaded the stock rom.
now when i try to flash it, preloader flashes FINE, recovery flashes FINE, but when it comes to md1img it shows this error: STATUS_INSUFFICIENT_BUFFER (0xC0010007). I tried flashing all the files individually to find the cause of the problem and see exactly which particular flash file was causing the problem. results are as follows.
[STATUS_INSUFFICIENT_BUFFER (0xC0010007) ]- this error was displayed while flashing these files - md1img, md1dsp, md1arm7, md3img.
[ STATUS_SEC_IMG_TOO_LARGE (0xC0020005)] - only popped up while flashing the oem image.
when I exclude these files from the queue, the rest files flash fine.
In short, I have a bricked phone which i am unable to flash via sp flash tool.
Thanks in advance
JDsingh007 said:
hi
so i have a Lenovo K8 plus 3 GB ram variant. Let me explain what happened first.
I unlocked my device's bootloader to flash the patched boot image for magisk root, then this orange state sign started showing up eerytime i booted up. then when the latest update rolled out in march, i decided to relock the bootloader and then update my device. did it and then a red state sign showing up accompanied by bootloop (it said something like rollback kernel too). so I formatted the whole thing via sp flash tool and downloaded the stock rom.
now when i try to flash it, preloader flashes FINE, recovery flashes FINE, but when it comes to md1img it shows this error: STATUS_INSUFFICIENT_BUFFER (0xC0010007). I tried flashing all the files individually to find the cause of the problem and see exactly which particular flash file was causing the problem. results are as follows.
[STATUS_INSUFFICIENT_BUFFER (0xC0010007) ]- this error was displayed while flashing these files - md1img, md1dsp, md1arm7, md3img.
[ STATUS_SEC_IMG_TOO_LARGE (0xC0020005)] - only popped up while flashing the oem image.
when I exclude these files from the queue, the rest files flash fine.
In short, I have a bricked phone which i am unable to flash via sp flash tool.
Thanks in advance
Click to expand...
Click to collapse
hey did you get it fixed and can you please send the link to the stock rom
yayjk said:
hey did you get it fixed and can you please send the link to the stock rom
Click to expand...
Click to collapse
TRY ASKING THE QUESTION ON THIS THREAD
https://forum.xda-developers.com/android/help/how-to-make-simple-android-apps-qna-t3776780
---------- Post added at 05:00 PM ---------- Previous post was at 05:00 PM ----------
JDsingh007 said:
hi
so i have a Lenovo K8 plus 3 GB ram variant. Let me explain what happened first.
I unlocked my device's bootloader to flash the patched boot image for magisk root, then this orange state sign started showing up eerytime i booted up. then when the latest update rolled out in march, i decided to relock the bootloader and then update my device. did it and then a red state sign showing up accompanied by bootloop (it said something like rollback kernel too). so I formatted the whole thing via sp flash tool and downloaded the stock rom.
now when i try to flash it, preloader flashes FINE, recovery flashes FINE, but when it comes to md1img it shows this error: STATUS_INSUFFICIENT_BUFFER (0xC0010007). I tried flashing all the files individually to find the cause of the problem and see exactly which particular flash file was causing the problem. results are as follows.
[STATUS_INSUFFICIENT_BUFFER (0xC0010007) ]- this error was displayed while flashing these files - md1img, md1dsp, md1arm7, md3img.
[ STATUS_SEC_IMG_TOO_LARGE (0xC0020005)] - only popped up while flashing the oem image.
when I exclude these files from the queue, the rest files flash fine.
In short, I have a bricked phone which i am unable to flash via sp flash tool.
Thanks in advance
Click to expand...
Click to collapse
TRY ASKING IN THIS THREAD
https://forum.xda-developers.com/android/help/how-to-make-simple-android-apps-qna-t3776780
How to Unbrick Lenovo K8 Plus 4GB
Hi All
I tried many stock roms and many versions of SP flash tool but none helped me to unbrick my lenovo k8 plus (4gb ram).
I was trying to downgrade it to Naugat from Oreo but it shows same error every time.
Error is (SP Flash tool version latest 5.18)
" Error_Status_Sec_Insufficient_Buffer( 0xC002004B)
[Hint]:
Verified boot is enabled.
Please download signed image (md1img-verified.img) or disable verified boot."
Plzzz help same problem
Enabled verified boot ...how to disabled
Same problem my lenovo k8plus
Enabled verified boot ...how to disabled
You need to use "Lenovo Moto Smart Assistant" instead of SPFlash tool to flash and you will be good to go. You can get the tool from the Lenovo official website.
JDsingh007 said:
hi
so i have a Lenovo K8 plus 3 GB ram variant. Let me explain what happened first.
I unlocked my device's bootloader to flash the patched boot image for magisk root, then this orange state sign started showing up eerytime i booted up. then when the latest update rolled out in march, i decided to relock the bootloader and then update my device. did it and then a red state sign showing up accompanied by bootloop (it said something like rollback kernel too). so I formatted the whole thing via sp flash tool and downloaded the stock rom.
now when i try to flash it, preloader flashes FINE, recovery flashes FINE, but when it comes to md1img it shows this error: STATUS_INSUFFICIENT_BUFFER (0xC0010007). I tried flashing all the files individually to find the cause of the problem and see exactly which particular flash file was causing the problem. results are as follows.
[STATUS_INSUFFICIENT_BUFFER (0xC0010007) ]- this error was displayed while flashing these files - md1img, md1dsp, md1arm7, md3img.
[ STATUS_SEC_IMG_TOO_LARGE (0xC0020005)] - only popped up while flashing the oem image.
when I exclude these files from the queue, the rest files flash fine.
In short, I have a bricked phone which i am unable to flash via sp flash tool.
Thanks in advance
Click to expand...
Click to collapse
Try with Lenovo Moto Smart Assistant. I too have bricked my phone... but I've successfully started my phone using this tool. you will get official signed ROM from here.
you can use LMSA tool to rescue,90% sucessfully ,don't use splashtool beacause it's many error if you choose wrong version
Had the same problem. Can confirm Lenovo's tool sucessfully recovers ohone from bricked state. A lifesaver!
Downloaded from https://lenovomobilesupport.lenovo.com/br/pt/downloads/ds101291-rescue-and-smart-assistant-lmsa
then updated to version 5.9.2.4 from inside the app itself
Hello, recently I've used flashify, and I tried to flash a twrp exclusive file. When I flash it, my phones screen turns black and I cannot power on the phone. Can anyone please help me?
Its sounds like you have flashed the recovery incorrectly. Flashify provides flashing of recovery and boot. Most probably you have flashed recovery in boot mistakenly and thats the cause of your phone not booting up.
your device have a Mediatek helio p60 chip, which makes it possible to reflash things using sp flash tools but before that. You have to fetch stock boot.img for your device to make it work again. Just download the firmware for your device and extract boot.img from it and reflash using sp flash tools.
Make sure to have proper Preloader drivers installed in your system before going ahead otherwise it'll not detect your phone. And the phone must have to be in switched off state. After that load the scatter file in the tool which I believe will come with the firmware package. After loading the scatter you'll see a list of things that will be flashed in your device. Just check or uncheck the things you want to flash. I suggest you to flash both recovery and boot back to stock and it will be running like normal.
Good luck
Happy & safe flashing:fingers-crossed:
Hit thanks if I helped you.:laugh:
My phone has somehow been bricked three days ago. It can't start until now after I tried to flash a custom recovery. After that, It restarts perpetually before it stopped continually. I can no more turn it on. I even tried to "flash a stock rom" using Sp flash tool with an MT6739 scatter file pac, but it doesn't work no more. I think this is because the files I downloaded are invalid for my device. Please could you help me find a way to bring back my phone into normal? How can I reinstall a stock rom for my device? Where can I find a valid firmeware for my model(Orange rise 55)?
Need help!
try this but compare scatter files are identical! and do not flash preloader!
https://firmware.gsm-social.com/index.php?a=downloads&b=file&id=11746
Thank you but I can not resolve this error "status_da_hash_mismatch" from flashing the stock rom with sp flash tool. could you help me?
that could mean a) wrong ROM, or b) you previously formatted the EMMC_USER which destroyed secure boot (secro)
you may be able to force flash with another Download Agent (and maybe auth_sv5.auth file is required)
https://blog.hovatek.com/so-whats-all-this-talk-about-meditek-secure-boot-and-da-files
Unbricking orange rise 55
Please need help! If it's a wrong rom, then where can I find a valid one?
you can dump from another working device
Please how can I get the Orange rise 55 firmware for free in order to recover my phone?
Could you help me please!