Has any tried charging honor 5x with 2amp charger??
How much time does it took to charge fully..??
With stock 1amp it took 3hrs to charge fully....as i know snapdragon 615 nd 616 support quick charge 2.0...can it be utilized with 2amp charger??
Sent from my KIW-L22 using Tapatalk
Good question. . I have a Qualcomm 2.0 fast charger at home, I'll plug mine into it and check the input
paoloroeseke said:
Good question. . I have a Qualcomm 2.0 fast charger at home, I'll plug mine into it and check the input
Click to expand...
Click to collapse
See how much it takes from 5% to 100%..[emoji41] by the way which honor 5x u have KIW-L22 or KIW-L24 ??
Sent from my KIW-L22 using Tapatalk
I dont understand what quick charge does exactly. If i have a charger that puts out 3 amps at 5 volts and the battery is 3000 mAh then it should take about an hour to charge if its completely drained. That the basic rule for 1C charging rate for lithiums right? so does the qualcomm charger deliver higher that 1C rates?
It doesn't actually work that way which would be bad for the battery, they charge faster when the battery is low and slow down as its fuller or reach a certain temperature.
As for Qualcomm quick charge, it works a bit different than the USB standard. I'm still not clear on the whole thing, but this is what I gathered:
Quick Charge 3.0
3.2v - 20v dynamic, 200mV increments
Up to 3A
Snapdragon 820, 620, 618, 617, and 430
Quick Charge 2.0
5V / 9V/ 12V
Up to 3A
Snapdragon 200, 400, 410, 615, 800, 801, 805, 808 and 810
-
5V/2A, 9V/2A, 12V/1.67A
Quick Charge 2.0 Class A can provide up to 24 watts over a micro USB connector, 36 watts with a Type-C connector, and Class B can reach 60 watts or more.
Quick Charge 1.0
5V, 2A
Snapdragon 600
This is the rating for one 19.5W QuickCharge 3.0 wall charger:
Output (Type-C Quick Charge 3.0 Port): 3.6-6.5V/3A, 6.5-9V/2A, and 9-12V/1.5A
eksasol said:
It doesn't actually work that way which would be bad for the battery, they charge faster when the battery is low and slow down as its fuller or reach a certain temperature.
As for Qualcomm quick charge, it works a bit different than the USB standard. I'm still not clear on the whole thing, but this is what I gathered:
Quick Charge 3.0
3.2v - 20v dynamic, 200mV increments
Up to 3A
Snapdragon 820, 620, 618, 617, and 430
Quick Charge 2.0
5V / 9V/ 12V
Up to 3A
Snapdragon 200, 400, 410, 615, 800, 801, 805, 808 and 810
-
5V/2A, 9V/2A, 12V/1.67A
Quick Charge 2.0 Class A can provide up to 24 watts over a micro USB connector, 36 watts with a Type-C connector, and Class B can reach 60 watts or more.
Quick Charge 1.0
5V, 2A
Snapdragon 600
This is the rating for one 19.5W QuickCharge 3.0 wall charger:
Output (Type-C Quick Charge 3.0 Port): 3.6-6.5V/3A, 6.5-9V/2A, and 9-12V/1.5A
Click to expand...
Click to collapse
Thanks for the info eksasol.. I guess I was just being simplistic. I always think of battery charging in terms of hobby remote control chargers for lipo's. True, the charger (or phone) must have built in circuitry to ramp up the amperage it delivers according to what it considers to be safe/efficient. It would slow down as it came up to it full voltage. Ive never really worried about it much since i just plug it in at night and get through the day without needing a recharge. Years ago in RC you could buy batteries that could handle 2C and above charging rates pretty easily. I would imagine that number has increased. I figured phone batteries would essentially be the same.
Kounjula Rahul said:
Has any tried charging honor 5x with 2amp charger??
How much time does it took to charge fully..??
With stock 1amp it took 3hrs to charge fully....as i know snapdragon 615 nd 616 support quick charge 2.0...can it be utilized with 2amp charger??
Sent from my KIW-L22 using Tapatalk
Click to expand...
Click to collapse
I did not actually use the supplied 1A charger, but with a standard 1A charger it takes all night.
My tablet 2A charger is way faster (a few hours maybe), honestly I did not take note of the time.
I will try that.
The charger circuit will take care of it, no matter the available current, because tension is fixed to 5V so resulting current will be what the circuit handles.
Not sure about a quickcharge 2.0 charger, don't have one.
idk why i read that it takes them atleast 4-6 hours to fully charge their battery? ehh in an hour mine goes from 6% to like 67% and then the other 30 mins and its done and full. and im just using the charger and cable that came with the phone.
paoloroeseke said:
Good question. . I have a Qualcomm 2.0 fast charger at home, I'll plug mine into it and check the input
Click to expand...
Click to collapse
You did try your Qualcomm 2.0 fast charger adapter ?
I'm using mine with samsung fast charger (the one that came with my note5) and it charges from 70%-100% in 19mins...according to GSam app
htc fan89 said:
I'm using mine with samsung fast charger (the one that came with my note5) and it charges from 70%-100% in 19mins...according to GSam app
Click to expand...
Click to collapse
At that rate (30% in 20 min), it should take around 60 min to reach 80% and (80 min) 1hr 20 min to Fully Charge with that charger.
I swear the original reviews said it took around 2 1/2-3 hrs to charge overnight.
I have to say I have NEVER had a phone last as long as this phone does! The battery lasts forever no matter what I do.
cyrusalmighty said:
At that rate (30% in 20 min), it should take around 60 min to reach 80% and (80 min) 1hr 20 min to Fully Charge with that charger.
I swear the original reviews said it took around 2 1/2-3 hrs to charge overnight.
I have to say I have NEVER had a phone last as long as this phone does! The battery lasts forever no matter what I do.
Click to expand...
Click to collapse
I haven't manage to kill it yet, but it should take 1hr30mins to fully charge maybe less. That's with a fast charger
Sent from my KIW-L24 using Tapatalk
I keep wanting to test how long a full charge takes, using my intelligent Anker charger. I never get the chance. The phone battery life is simply outstanding. This is like my 8th smart phone, and simply blows the rest out of the water. I even have the EUMI battery saving features turned off. A 50% charge can takes about an hour. Old habits of always plugging it in when in the car or my desk means that I can forget about plugging it in at night. Don't worry about battery life or fast charging - they are non issues.
No QC2
I have tried two different adapters that are QC2 compatible (and work fine with Galaxy Note 4) with USB voltage measurement device; all I can get is 5V and 1A max even when the battery charges from 20% on.
So, no go on QC2
Also tried QC2.0 charger. No fast charging. However, Ampre, does report that it manages to pull 1.3A from the variable amperage ports i have.
I finally got my battery down to 0%. With Ampre reporting:
- Using a 0.5 amp charger, I got constant 460mA
- Using the 1.0 amp supplied charger I got 850mA
- Using my Anker 5A IQ charger (i think they license the QC technology) I only got 850mA. I checked and was using a power not data+power cable.
- Using same Anker 5A IQ charger, and a high quality power only Anker cable I got 1850 mA up until 50% charge then 1600 until 65% charge and 1200 until 85% charge. After that it dropped off rapidly 750 at 90%, and 450 at 95%.
Charging when using the phone lightly - occasional call, calendar update, email - consumes around 400 mA. I do not use any of the Honor power saving features. With this in mind:
- 40 min from 0 to 60%
- 1 hour 40 min from 0 to 90%.
Perfectly acceptable to me with the huge battery. GET RID OF YOUR CHEAP POWER CABLES
So IQ or QC chargers do seem to work, and most importantly make sure you have good quality power only cables. I have a drawer full of cables that were fine with older phones and chargers. They are now in the trash.
in china model support quick charge 2
in china model support quick charge 2
Bear100 said:
I finally got my battery down to 0%. With Ampre reporting:
- Using a 0.5 amp charger, I got constant 460mA
- Using the 1.0 amp supplied charger I got 850mA
- Using my Anker 5A IQ charger (i think they license the QC technology) I only got 850mA. I checked and was using a power not data+power cable.
- Using same Anker 5A IQ charger, and a high quality power only Anker cable I got 1850 mA up until 50% charge then 1600 until 65% charge and 1200 until 85% charge. After that it dropped off rapidly 750 at 90%, and 450 at 95%.
Charging when using the phone lightly - occasional call, calendar update, email - consumes around 400 mA. I do not use any of the Honor power saving features. With this in mind:
- 40 min from 0 to 60%
- 1 hour 40 min from 0 to 90%.
Perfectly acceptable to me with the huge battery. GET RID OF YOUR CHEAP POWER CABLES
So IQ or QC chargers do seem to work, and most importantly make sure you have good quality power only cables. I have a drawer full of cables that were fine with older phones and chargers. They are now in the trash.
Click to expand...
Click to collapse
+1 this is the same results I experienced. My phone rarely goes below 50% charge in a normal day
thanks guys, guess i'll get it - 120 on sale for prime day
starscalling said:
thanks guys, guess i'll get it - 120 on sale for prime day
Click to expand...
Click to collapse
worth the extra post - i can confirm the fast charging - was still doing about a percent a minute between 70% and 80% or so. little laggy during setup, occasionally seems to miss a command but dang for the price i can't complain.
using my zenfone2 fastcharger - rox.
Hi i read that redmi 5 plus support qc so i had aquired samsung quick charger.When plugged phone shows quick charging but when i mesure mA while charing with qc and with normal charger there is no big difference according mesuring software.So what is real truth about qc?
petric1 said:
Hi i read that redmi 5 plus support qc so i had aquired samsung quick charger.When plugged phone shows quick charging but when i mesure mA while charing with qc and with normal charger there is no big difference according mesuring software.So what is real truth about qc?
Click to expand...
Click to collapse
Redmi 5 Plus supports QC (3.0 to be exact, as it's Snapdragon 625). Apps measuring charge rate won't show you real current, it's only approximation.
I've tested my charger, which supports QC 3.0, my 5+ uses 9Volts at almost 2Amps (when charging from 15-20%). Measuring software won't show you voltage that you are using to charge so you may not see the difference. But doing quick math - 5V*2A=10W (standard charging brick) whereas QC charger will use 9V*2A=18W. That means you are charging with 80% more power.
Keep in mind that charging with QC will get your phone a bit warmer, so phone will start to throttle the current, meaning that you won't be charging from 0% to 100% at full 18W
Yes. It charges with 9v and 1,7 amp max. (9v is static, amp is variable, that means it has only QC 2.0 mode.)
Its way faster than standart charger. I have Tronsmart QC 3.0 charger. But you can go with QC 2.0 charger.
Hi everyone, I got couple of USB testers that I know works perfectly fine and also a QC4 charger (which is backwards compatible) and I noticed that Mi A3 does not support QC whatsoever. Device only charges at maximum of 10Ws (5v 2A, is the maximum I got). Did anyone else notice that? gsmarena listing shows it allegedly supports 18W but I havent been able to get to charge at those speeds, can anyone else confirm Mi A3 is charging at 10W max?
Before you all comment it supports "rapid charge" phone says its rapid charging for 10W, I tried at different charge levels using different cables chargers.
I have a genuine Xiaomi 18W fast charger & the phone correctly identifies it & fast charging is working fine. May be your unit is faulty or something.
I actually just rechecked. It actually ramps up the voltage slowly, 0.1 increments then eventually reaches 12v at 1.5amps. Previous phone I had would set the voltage to 9V (I had a LG G4) instantly. It works! sorry for the confusion.
Hello people, is anyone aware if using the 65Watt charger that comes in the box is safe to use with other low power devices like bluetooth headsets or other devices?
Please answer if you're educated on this or have tried it.
i use it for charging huawei band 3 and y6 via microusb cable and dont see any issues
Aside from the 65W (10V 6.5 A), the rating on the charger also displays 5V 2A output, which is normal charging specs for device not compatible with the fast charging, so it should be fine.
If you find any device that use the same protocol or 10V 6.5 A it will charge it super fast
But most other phones use different charging volt and ampere so it will not be able to super charge it
For example my wife owns a s20 fe who is capable of 25w charging
But the charger of realme just a charge it at 10w with 5 volt 2 ampere
What charging speeds can you get with QC, USB-PD or USB-PD PPS chargers? Higher than 7.5W / 5v 1.5A at least?
I see OnePlus lists it's charging speed as "18W Fast Charging (9V/2A)". And 9v doesn't match the 5v or 10v that I've read Dash/Warp/VOOC has used. So I'm hoping that means it supports more that just Dash/Warp.
If the nord n200 does require only Dash/Warp, anyone know which version?
According to this link:
https://www.reddit.com/r/oneplus/comments/u78u1o
The "PD" indicator on a cable with integrated power meter lights up, so the author thinks it is USB-PD.
Getting 10.2W (8.88v 1.15A) with QC. Battery was at 75% though. Have to test further at a lower charge level.
Used a Motorola "turbopower" USB-A charger, model: SC-22, which apparently does Qualcomm QC. Labeled as capable of 15W, 5v 3A, 9v 1.6A or 12v 1.2A.
~edit~
16.3W (8.94v 1.83A) via Qualcomm QC with a different cable and the battery at 10%. Max rate my charger is capable of.