Hi all,
I am completely stuck with this, I couldnt get any wifi it wouldnt turn on and when I did it just turned off again. It also wont read my sim card and randomly restarts.
I tried factory resetting but its now just stuck getting me through the android setup and needs internet in order for me to register the account that I previously used on the phone, otherwise it wont let me pass. It wont turn on wifi still and still doesnt register my sim card.
Please help as I have been trying this for hours and Im honestly at the end of my rope.
Cheers,
Evan
update:
I have tried,
factory reset
Flashing the rom,
downgrading,
upgrading,
wiping everything and putting latest miui again,
used twrp for running a recovery.
None of this has worked - all came to the same problem
So i believe that I found the issue. I managed to actually get in to the phone without needing to login to my mi account after a long few hours troubleshooting. Managed to boot in to miui 9.
I can see that my IMEI numbers are showing as UNKNOWN
I am going to see if I can find the box for my phone and then get the imei numbers back in the EFS file using miracle box
** :UPDATE 2.0: **
Hi.
So I am now witnessing really strange behavior.......
The phone will reboot ocassionally. Ive not recorded a pattern but every now and again it will register the SIM card but wont turn on the wifi.
The IMEI numbers will show, the base band version will show and the mac address. But I dont think they are correct.....
----------
Its showing
IMEI (SLOT1):
868xxxxxxxxx333
IMEI (sv1)
00
IMEI (SLOT2):
868xxxxxxxxx341
IMEI (sv2)
00
----------------------------
Baseband version:
Will update on next reboot that shows it as I didnt manage to capture the data when it did actually appear
----------------------------
Mac address:
02:00:00:00:00:00
I don't think some of this is correct.....
Like the mac address.... It doesnt look right to me.....
Anyone help with these symptoms?
It wont actually connect to any network still when it shows these details and after a short few minutes will restart and show them as unknown again.
Kind regards,
Evan
Try fastboot rom
Evoku said:
** :UPDATE 2.0: **
Hi.
So I am now witnessing really strange behavior.......
The phone will reboot ocassionally. Ive not recorded a pattern but every now and again it will register the SIM card but wont turn on the wifi.
The IMEI numbers will show, the base band version will show and the mac address. But I dont think they are correct.....
----------
Its showing
IMEI (SLOT1):
868xxxxxxxxx333
IMEI (sv1)
00
IMEI (SLOT2):
868xxxxxxxxx341
IMEI (sv2)
00
----------------------------
Baseband version:
Will update on next reboot that shows it as I didnt manage to capture the data when it did actually appear
----------------------------
Mac address:
02:00:00:00:00:00
I don't think some of this is correct.....
Like the mac address.... It doesnt look right to me.....
Anyone help with these symptoms?
It wont actually connect to any network still when it shows these details and after a short few minutes will restart and show them as unknown again.
Kind regards,
Evan
Click to expand...
Click to collapse
Try with a fastboot rom flashing via miflash...this will fix all system issues. You can search in xda for fastboot rom links .it ends with .tgz
Thanks
sssyraj said:
Try with a fastboot rom flashing via miflash...this will fix all system issues. You can search in xda for fastboot rom links .it ends with .tgz
Thanks
Click to expand...
Click to collapse
I already tried to flash several global releases from Mis website and had the same error with the imei on each one. Will a rom from here actually be any different?
sssyraj said:
Try with a fastboot rom flashing via miflash...this will fix all system issues. You can search in xda for fastboot rom links .it ends with .tgz
Thanks
Click to expand...
Click to collapse
can you recommend a rom to fix this? I just tried the [UnBrick] one that uses the version 10.xxx miui rom. Im in but same issue with no network and imei numbers missing etc
sssyraj said:
Try with a fastboot rom flashing via miflash...this will fix all system issues. You can search in xda for fastboot rom links .it ends with .tgz
Thanks
Click to expand...
Click to collapse
Okay I think I'm completely screwed. I am unable to edit the qcn/unable to restore from a custom qcn and I can't get find any roms that fix the issue.
SOMEONE PLEASE HELP THIS IS STRESSING ME OUT SO MUCH, I JUST WANT MY PHONE TO WORK AGAIN
@Mod plz can you recommend anyone to help me out??
The fastboot rom is different from the one that use to be flashed with twrp. Did you given a try with fastboot rom? Internet is required while flashing with miflash as it uses your mi account. Don't loose hope.
Thanks.
sssyraj said:
The fastboot rom is different from the one that use to be flashed with twrp. Did you given a try with fastboot rom? Internet is required while flashing with miflash as it uses your mi account. Don't loose hope.
Thanks.
Click to expand...
Click to collapse
every time I flashed it was with fastboot :/
Evoku said:
every time I flashed it was with fastboot :/
Click to expand...
Click to collapse
Have you tried flashing with the MiFlash tool? Or is this what you meant by fastboot?
I know this isn't the help you're looking for but if you need your phone to work just take it to a service center. It'll cost money off course, but they'll help you. Some service centers do it within a few minutes
The same problem than me
Hello Evoku, how r u?
Sorry for my poor English, but I'm from Brazil.
Look what a coincidence. By the same day your first post my pocophone f1 presented the same problem than yours. I am searching for a solution and now I found this forum.
Can you tell me if got some solution?
https://forum.xda-developers.com/poco-f1/how-to/super-guide-persist-file-magical-file-t3953938
guys try this
ron_hyatt said:
https://forum.xda-developers.com/poco-f1/how-to/super-guide-persist-file-magical-file-t3953938
guys try this
Click to expand...
Click to collapse
I'll try, thanks. Late i'll bring news
ron_hyatt said:
https://forum.xda-developers.com/poco-f1/how-to/super-guide-persist-file-magical-file-t3953938
guys try this
Click to expand...
Click to collapse
Bro, I've tried your issue, but to do the bootloader I need SIM Card be recognized and this is just the problem
Hi!!
I have the same problem, any good news?
i have the same problem.. when i connet to wifi after fastboot rom flash it goes to sleep and never works again.. then i have to flush fastboot rom again and again. what should i do
Watch this
https://youtu.be/7dzVh7c9Q5Q
Try the persist fix. If that doesnt help, i doubt that some box will, as it appears to be a hardware issue..
Hi guys, some problem to me and I just fix it.
I noticed that if the phone is switched off for at least 10 minutes then wifi and SIM card are working for some minutes before stop. I used this time to unlock the bootrom, install the TWRP, root the phone and backup the EFS partition ready to apply the "Super guide: Persist file the magical file". On TWRP I noticed that I don't have the persist partition for the magical file. Anyhow I powered on the phone and now WiFi and SIM card are working properly! Hope this helps.
Related
Weird problem ....phone doesn't recognize sim.
5.1.1 cm12.
Thanks for any suggestion
rockky said:
Weird problem ....phone doesn't recognize sim.
5.1.1 cm12.
Thanks for any suggestion
Click to expand...
Click to collapse
Does it show up on stock? Which rom are you using?
Is it your Sim or do you need your signal? If that you have to enter the apn manually
Did you install/Update to CM 12.1 build?
Do you have baseband unknown under settings>About phone?
If you are new to CM12.1 and have baseband unknown issue. This is a common issue going around for CM based ROMs
you may need to flash stock sony FTF if yours is a non GPE model and then root and flash recovery.
You will get baseband back
sjesudasan said:
Did you install/Update to CM 12.1 build?
Do you have baseband unknown under settings>About phone?
If you are new to CM12.1 and have baseband unknown issue. This is a common issue going around for CM based ROMs
you may need to flash stock sony FTF if yours is a non GPE model and then root and flash recovery.
You will get baseband back
Click to expand...
Click to collapse
Hello to you, I know you posted this a while ago, but I'm having the same problem on a Z ultra bought second hand... I have the error message invalid sim card after inputing the sim code (so the sim card is detected, and is working in another phone) I also have the error unknown baseband as you described. In the same way, when in service menu, if I want to check SIM lock in service info, the app freeze too without displaying anything.
I don't know what the other owner did to the phone though.
any clue for what to do ? I flashed the latest original rom ( 14.4.A.0.108) through flashtool - still sim card invalid -, then tried to flash through cwm another rom, but still the same.
There is also another bug, i don't know whether it's linked or not, but i can't take a picture with the camera app, the app freeze when I click the button !
Any help would be gladly appreciated !
Hi Kwenteen,
Did you get "unknown baseband" after flashing some ROM? If yes, try flashing KitKat ROM first and then see if you get baseband. I'm suspecting the flashing process didn't go well.
This is a known bug with CM12 ROM for ZU go to dial pad and dial *#06# and the Imei will show up if it shows unknown either flash the Modem zip or flash the stock ROM again
sjesudasan said:
Hi Kwenteen,
Did you get "unknown baseband" after flashing some ROM? If yes, try flashing KitKat ROM first and then see if you get baseband. I'm suspecting the flashing process didn't go well.
Click to expand...
Click to collapse
Hello sjesudasan, thanks for your help,
I tried to flash numerous original roms, starting all the way down to 290, which is 4.3, that displayed properly the emei number, but didn't allow me to pass phone calls (sim card detected, ask for pin code, then no service)
And I can't enter any APN.
On top of that, I am now unable to flash anything with xperia flashtool anymore, getting a null error then error flashing. Aborted. when trying to flash any firmware and the device doesn't boot anymore either. I guess the last flash went wrong even if it didn't display any error, but I assumed that as long as I was able to put the phone in flashmode, I would be able to flash anything, and get away from softbrick ?
when trying to fix with Xperia compagnon, I get the error "UEGetPhoneInfoMissingInfo "
Thank you for your suggestion sairaj rane, unfortunately I already tried that, went back to original firmware, I even flashed the modem zip. None of those solution worked for me.
Thank you for your help !
Hello, after 2 weeks of trouble just to get back with a functionning 5.1.1 ROM, I now have an original sony rom fixed by xperia compagnion.
I have the same error, can't get to the network. Phone ask for simcode, I enter it, and then no error, just no connexion to the network.
I have a recognized emei number, but the ICCID says unknown...
Is it normal ?
Thanks for the help anyway !
kwenteen said:
Hello, after 2 weeks of trouble just to get back with a functionning 5.1.1 ROM, I now have an original sony rom fixed by xperia compagnion.
I have the same error, can't get to the network. Phone ask for simcode, I enter it, and then no error, just no connexion to the network.
I have a recognized emei number, but the ICCID says unknown...
Is it normal ?
Thanks for the help anyway !
Click to expand...
Click to collapse
Have you tried the repair function of xperia companion?
itsmeluigi said:
Have you tried the repair function of xperia companion?
Click to expand...
Click to collapse
Unfortunately, yes.
It worked in a way that allowed me to retrieve the phone from a pretty hard brick, in conjunction with the use of the test point method and s1tool …
but even after this awakening from the dead, still no network connection.
Have you checked the six golden Pins inside the Phones SIM Slot? (Hard to see)
Once my phones one was bent. Had to correct them with a fine tool. Sim recognized since then.
kwenteen said:
Unfortunately, yes.
It worked in a way that allowed me to retrieve the phone from a pretty hard brick, in conjunction with the use of the test point method and s1tool …
but even after this awakening from the dead, still no network connection.
Click to expand...
Click to collapse
Thanks itsmeluigi,
I just checked that, dremelled the protective shield to access them, and probed them with a multimeter. No good, everything is fine there !
kwenteen said:
Thanks itsmeluigi,
I just checked that, dremelled the protective shield to access them, and probed them with a multimeter. No good, everything is fine there !
Click to expand...
Click to collapse
Tried to flash with another cable on another Pc with another Firmware download (Source)?
itsmeluigi said:
Tried to flash with another cable on another Pc with another Firmware download (Source)?
Click to expand...
Click to collapse
Yep, done that too...
To be honest, I really don't know what to do.
I don't know if that can be linked, but the phone is also unable to be unlocked, despite the code provided by sony, matching the imei number !
Hello Guys, so as described in the title it all started when i wanted to unlock bootloader unofficially, im not a newbie but didn't expect Xiaomi to act like samsung in terms of making it a big headache to unlock the device...
anyway the unofficial method consist of flashing MIUI 7.1.8.0 while i was on 8.0.x.x if im not mistaken
I had my sim in my main phone in the process so im not really sure when did i basically lose the IMEI, baseband, MAC address all these things but i discovered that i lost them and spent like 2 weeks searching and tryingdifferent tutorials (i have like 50 bookmarks and maybe downloaded like 30GB worth of data!!)
Final/Current situation:
IMEI1 and IMEI2 recovered --> can log in to Mi account
MAC address recovered --> can connect to wifi
Service NOT recovered, phone detect the sim, it shows the sim number in settings, even the access points are read from the sim and shown in the Access Point area but whatever i do the sim card shows No service
last thing i did is i flashed MIUI9 beta official, locked bootloader, stock recovery...
I hope this thread get some attention for me and many others as well...ready to answer any extra clarifications
It's Redmi Note 3 Special Edition (SE)
[Product Code is 2015161 which is for kenzo according to thsi http://en.miui.com/thread-449310-1-1.html]
Qualcomm Snapdragon 650 CPU
Dual SIM
Did you try using another sim card?
zeon321 said:
Did you try using another sim card?
Click to expand...
Click to collapse
I tried using the same sim card on another device and it works
Maybe this will work for U: https://labs.xda-developers.com/store/app/tech.kandara.imeiidchanger
Hackintoshler said:
Maybe this will work for U: https://labs.xda-developers.com/store/app/tech.kandara.imeiidchanger
Click to expand...
Click to collapse
I dont have any problem with IMEI anymore, i an even log in to MI account which i wasnt able to do when i lost my IMEI due to "device ID verification failure"
try using this way ,this tutorial is Indonesian.
but hope this helps your problem.
http://www.miuitutorial.com/2016/11/sinyal-xiaomi-redmi-note-3-pro-hilang.html?m=1
Zacky.gates777 said:
try using this way ,this tutorial is Indonesian.
but hope this helps your problem.
http://www.miuitutorial.com/2016/11/sinyal-xiaomi-redmi-note-3-pro-hilang.html?m=1
Click to expand...
Click to collapse
cant open the download link
All_New_BoB said:
cant open the download link
Click to expand...
Click to collapse
Here
https://drive.google.com/file/d/0B18XY8MQp2z9Vm9VUU5TcjNYWVE/view?usp=drivesdk
password : www.robothijau97.com
@All_New_BoB You disappeared suddenly, can you confirm if you've fixed the issue?
VaibhavKumar07 said:
@All_New_BoB You disappeared suddenly, can you confirm if you've fixed the issue?
Click to expand...
Click to collapse
Hello, sorry for disappearing its just that i spent so much time trying to fix it and then i realize that the phone is actually kate not kenzo....honestly i dont know where to go from here, i dont even know what rom there is on my phone right now...all i know is that its not booting as usual and doesnt have custom recovery. i will try to at least make it boot today so hopefully ill get some support from you guys. ill try to install twrp recovery and flash LineageOS 14.1
ok so i actually restored a backup i made before and im now on resurrction remix 7.1.2 with everything working except data
I have the same problem.
I try to flash new kate qcn file and restore imeis.
I try to flash some firmwares.
I only have network sigal in last miui9 developer for note 3 pro se (kate). No network on nougat and oreo.
Hi all,
I just wanted to share what I did when I had a few problems with my Lenovo K6 Note - karatep.
What did I do which ruined my phone?
I unlocked my bootloader, still on stock ROM, haven't installed TWRP yet.
Since then no calls on non-VoLTE network like Vodafone/Airtel/BSNL.
Primary SIM doesn't connect to any other network than 4G.
I had installed CM15.1 ROM with TWRP and Magisk root and I had the same network issues.
When should you follow this guide?
You have problems with network connectivity where you can't make calls on 3G or 2G network.
Primary (data) slot doesn't connect to 3G or 2G.
No signal on either one slot or both the slots.
IMEI shown as null or 0.
WiFi and Bluetooth address either different or shown as unavailable.
Rebooting to fastboot and performing "fastboot erase modemst1; fastboot erase modemst2" didn't work for you and lost your IMEI and/or WiFi and Bluetooth address.
Do not reboot to fastboot and execute "fastboot erase modemst1; fastboot erase modemst2". I lost my IMEI and MAC because of this.
Requirements:
1. Your phone needs to have root access.
2. Your original IMEI numbers and WiFi address, you can find them from your phone's packaging box.
If you don't have your IMEI, better use an IMEI from an old/dead phone of yours. Don't google this up, there can be blacklisted IMEIs.
Steps:
Preparing the .QCN file for restoration
Download and install UltraEdit (you can google up this for the link)
Download and install Qualcomm QPST/QFIL downloader (google it again)
Download IMEI Converter (find it in the attachments below)
Download .QCN file (find it in attachments, this is for Lenovo K6 Note - karatep)
Get your IMEI (for both the slots), WiFi and Bluetooth addresses
Open IMEI Converter and type your IMEI. You will get the hexcode for your IMEI, get the hexcode for both of your IMEIs. Copy the hexcodes.
Open the .QCN file with UltraEdit and search for "08 8A 11 11 11 11 11 11 11" (without the quotes). This is the dummy IMEI in the file, you have to replace it with your phone's IMEI.
In UltraEdit, goto find and replace, search for 08 8A 11 11 11 11 11 11 11 and replace it with your IMEI's hexcode. You have to replace the first hexcode with the hexcode for your second slot's IMEI and the second hexcode with the hexcode for your first slot's IMEI.
Search for AA AA AA AA AA AA and replace it with your WiFi MAC address, this has to update your Bluetooth address as well, there are four places where you have to replace it with your WiFi MAC address.
Save the .QCN file and close UltraEdit.
Enabling DIAG COM port on your phone to download .QCN to your phone
Execute in command prompt.
adb shell
su
setprop sys.usb.config diag,adb
Click to expand...
Click to collapse
This will enable the diagnostic port on your phone.
Restoring .QCN to your phone
Open QFIL as administrator.
Connect your phone to your computer, keep your phone powered on with DIAG port enabled.
Goto Tools -> QCN Backup Restore
Browse your edited .QCN file
Don't change SPC code - leave it as such.
Select Enable Multi-SIM.
Click on Restore QCN.
This will take some time, once done, restart your phone.
Voila! Your IMEI, WiFi and Bluetooth addresses should be updated and network should be able to receive signal and place calls.
Please feel free to reach me if you run into any issues, I'll try my best to help you!
Thanks,
tfr!
reserved
anyone with .QCN file for K6 Power (k33a42)?
If you di then please share it or tell me where to get it!
Thanks in advance.
manishurfmannu said:
anyone with .QCN file for K6 Power (k33a42)?
If you di then please share it or tell me where to get it!
Thanks in advance.
Click to expand...
Click to collapse
If you get qcn file for Lenovo k6 power share with me
pranavpro0001 said:
If you get qcn file for Lenovo k6 power share with me
Click to expand...
Click to collapse
flash the stock S223 firmware, it will fix the issue.
manishurfmannu said:
flash the stock S223 firmware, it will fix the issue.
Click to expand...
Click to collapse
No it will not. Flashing stock firmware even with QFIL will not fix baseband issue.
I did this but....
theflyingrahul said:
Hi all,
I just wanted to share what I did when I had a few problems with my Lenovo K6 Note - karatep.
What did I do which ruined my phone?
I unlocked my bootloader, still on stock ROM, haven't installed TWRP yet.
Since then no calls on non-VoLTE network like Vodafone/Airtel/BSNL.
Primary SIM doesn't connect to any other network than 4G.
I had installed CM15.1 ROM with TWRP and Magisk root and I had the same network issues.
When should you follow this guide?
You have problems with network connectivity where you can't make calls on 3G or 2G network.
Primary (data) slot doesn't connect to 3G or 2G.
No signal on either one slot or both the slots.
IMEI shown as null or 0.
WiFi and Bluetooth address either different or shown as unavailable.
Rebooting to fastboot and performing "fastboot erase modemst1; fastboot erase modemst2" didn't work for you and lost your IMEI and/or WiFi and Bluetooth address.
Do not reboot to fastboot and execute "fastboot erase modemst1; fastboot erase modemst2". I lost my IMEI and MAC because of this.
Requirements:
1. Your phone needs to have root access.
2. Your original IMEI numbers and WiFi address, you can find them from your phone's packaging box.
If you don't have your IMEI, better use an IMEI from an old/dead phone of yours. Don't google this up, there can be blacklisted IMEIs.
Steps:
Preparing the .QCN file for restoration
Download and install UltraEdit (you can google up this for the link)
Download and install Qualcomm QPST/QFIL downloader (google it again)
Download IMEI Converter (find it in the attachments below)
Download .QCN file (find it in attachments, this is for Lenovo K6 Note - karatep)
Get your IMEI (for both the slots), WiFi and Bluetooth addresses
Open IMEI Converter and type your IMEI. You will get the hexcode for your IMEI, get the hexcode for both of your IMEIs. Copy the hexcodes.
Open the .QCN file with UltraEdit and search for "08 8A 11 11 11 11 11 11 11" (without the quotes). This is the dummy IMEI in the file, you have to replace it with your phone's IMEI.
In UltraEdit, goto find and replace, search for 08 8A 11 11 11 11 11 11 11 and replace it with your IMEI's hexcode. You have to replace the first hexcode with the hexcode for your second slot's IMEI and the second hexcode with the hexcode for your first slot's IMEI.
Search for AA AA AA AA AA AA and replace it with your WiFi MAC address, this has to update your Bluetooth address as well, there are four places where you have to replace it with your WiFi MAC address.
Save the .QCN file and close UltraEdit.
Enabling DIAG COM port on your phone to download .QCN to your phone
Execute in command prompt.
This will enable the diagnostic port on your phone.
Restoring .QCN to your phone
Open QFIL as administrator.
Connect your phone to your computer, keep your phone powered on with DIAG port enabled.
Goto Tools -> QCN Backup Restore
Browse your edited .QCN file
Don't change SPC code - leave it as such.
Select Enable Multi-SIM.
Click on Restore QCN.
This will take some time, once done, restart your phone.
Voila! Your IMEI, WiFi and Bluetooth addresses should be updated and network should be able to receive signal and place calls.
Please feel free to reach me if you run into any issues, I'll try my best to help you!
Thanks,
tfr!
Click to expand...
Click to collapse
i have Lenovo k6 note ,i don't know about the karatep part, it's in the vibe series ,k53a48 is the name with 4 GB ram,
I lost my IMEI, sn etc after doing the fastboot commands in an attempt to fix the common radio band issue of enabling us bands..but wifi, Bluetooth, etc weren't affected at all..
I've flashed qcn file from a youtube video after editing the IMEI to my own ..everything is restored, baseband,SN number(sn number is not mine tho),IMEI all..
but,
my phone still cant read sim cards, it says that the sim is not ready.. earlier the phone couldn't even recognize that i ve inserted the sim but after the qcn flash it can do that..but still it says sim card not ready...
please help me sir its been months! please?
i m running on the stock rom of Lenovo k6 note
guitargeek0517 said:
i have Lenovo k6 note ,i don't know about the karatep part, it's in the vibe series ,k53a48 is the name with 4 GB ram,
I lost my IMEI, sn etc after doing the fastboot commands in an attempt to fix the common radio band issue of enabling us bands..but wifi, Bluetooth, etc weren't affected at all..
I've flashed qcn file from a youtube video after editing the IMEI to my own ..everything is restored, baseband,SN number(sn number is not mine tho),IMEI all..
but,
my phone still cant read sim cards, it says that the sim is not ready.. earlier the phone couldn't even recognize that i ve inserted the sim but after the qcn flash it can do that..but still it says sim card not ready...
please help me sir its been months! please?
i m running on the stock rom of Lenovo k6 note
Click to expand...
Click to collapse
Hello,
Sorry for the late reply, we have a bad network connection here due to the lockdown.
Coming to your problem, karatep simply refers to K6 Note, so you have done the right procedure hopefully.
Can you see the IMEI when you enter *#06# in the Dialer?
You're on stock ROM right? Where did you get it from? You did a full flash with QFIL or a ROM flash only? Please note that ROM flashes can be dirty.
If you can see your IMEI, please try the following in the order I've mentioned below.
1. Check the network settings and select the proper network type. Especially if you are on Jio, set it to LTE only, make sure that the non-Jio SIM is set to GSM only. This is the most common problem.
2. Perform a full system reset from recovery, must solve the problem usually.
3. Try lineage 15.1 or 16.0, you'll be able to find the links here, they are really stable and worth upgrading.
4. Full factory flash with QFIL, you should be able to find videos on YouTube, else let me know, I'll be happy to help!
Let me know the results.
Happy to help!
rah.
theflyingrahul said:
Hello,
Sorry for the late reply, we have a bad network connection here due to the lockdown.
Coming to your problem, karatep simply refers to K6 Note, so you have done the right procedure hopefully.
Can you see the IMEI when you enter *#06# in the Dialer?
You're on stock ROM right? Where did you get it from? You did a full flash with QFIL or a ROM flash only? Please note that ROM flashes can be dirty.
If you can see your IMEI, please try the following in the order I've mentioned below.
1. Check the network settings and select the proper network type. Especially if you are on Jio, set it to LTE only, make sure that the non-Jio SIM is set to GSM only. This is the most common problem.
2. Perform a full system reset from recovery, must solve the problem usually.
3. Try lineage 15.1 or 16.0, you'll be able to find the links here, they are really stable and worth upgrading.
4. Full factory flash with QFIL, you should be able to find videos on YouTube, else let me know, I'll be happy to help!
Let me know the results.
Happy to help!
rah.
Click to expand...
Click to collapse
Thank you for the reply,
i do see my imei when i enter the code, Its the sn number that has been changed..
and about the stock rom part, I didn't do it by myself, i had given the phone to a repair shop earlier to fix the issue, this was before i flashed the QCN myself,
i flashed the qcn from a youtube video and all that guy had told was to have stock rom marshmallow, the repair shop had flashed a marshmallow rom so i figured it would do.. but i dont know what tool they used to flash it..
i used QFIL to flash the QCN though..
Let me try the factory reset solution and if that dont work i ll try to flash stock rom again...
for the other two,
1. The network settings are inaccessible for me(i tried to attach screenshots but its asking for URLs)
3. I really dont want to use lineage OS if i dont have to..
let me try the other solutions and i ll let you know..
thank you so much for helping me..
guitargeek0517 said:
Thank you for the reply,
i do see my imei when i enter the code, Its the sn number that has been changed..
and about the stock rom part, I didn't do it by myself, i had given the phone to a repair shop earlier to fix the issue, this was before i flashed the QCN myself,
i flashed the qcn from a youtube video and all that guy had told was to have stock rom marshmallow, the repair shop had flashed a marshmallow rom so i figured it would do.. but i dont know what tool they used to flash it..
i used QFIL to flash the QCN though..
Let me try the factory reset solution and if that dont work i ll try to flash stock rom again...
for the other two,
1. The network settings are inaccessible for me(i tried to attach screenshots but its asking for URLs)
3. I really dont want to use lineage OS if i dont have to..
let me try the other solutions and i ll let you know..
thank you so much for helping me..
Click to expand...
Click to collapse
Hello,
You cannot do anything about the serial number, there is currently no way to restore it, it should not limit the functionality of the device.
Is your phone rooted now? Do you have TWRP installed? Try resetting the phone from TWRP. If it doesn't work, restore stock rom with QFIL. Restoring with QFIL will reprogram your eMMC chip and revert it to stock, TWRP will be removed. This will give you the cleanest possible install.
For flashing QCN, you don't need stock Marshmallow. I'm on Lineage 16.0 and I keep changing my MAC address with QFIL, that is not a problem at all.
I'd like to see the screenshots, you can add them as attachments... Use the paper clip icon above, else upload the image to Google Drive and put the URL here.
Happy to help!
rah.
guitargeek0517 said:
Thank you for the reply,
i do see my imei when i enter the code, Its the sn number that has been changed..
and about the stock rom part, I didn't do it by myself, i had given the phone to a repair shop earlier to fix the issue, this was before i flashed the QCN myself,
i flashed the qcn from a youtube video and all that guy had told was to have stock rom marshmallow, the repair shop had flashed a marshmallow rom so i figured it would do.. but i dont know what tool they used to flash it..
i used QFIL to flash the QCN though..
Let me try the factory reset solution and if that dont work i ll try to flash stock rom again...
for the other two,
1. The network settings are inaccessible for me(i tried to attach screenshots but its asking for URLs)
3. I really dont want to use lineage OS if i dont have to..
let me try the other solutions and i ll let you know..
thank you so much for helping me..
Click to expand...
Click to collapse
What's your network BTW?
Here are the screenshots
https://drive.google.com/folderview?id=1Bxed7rCpd0MoVbnZCSGtJBjAlmgVkF1r
And no my phone is not rooted and nor is TWRP installed..i was planning on rooting it as a last resort..
I m now currently downloading the stock rom file..its nearly completed..
Should i try rooting it before flashing stock? I dont want to risk another brick cause of rooting
guitargeek0517 said:
https://drive.google.com/folderview?id=1Bxed7rCpd0MoVbnZCSGtJBjAlmgVkF1r
And no my phone is not rooted and nor is TWRP installed..i was planning on rooting it as a last resort..
I m now currently downloading the stock rom file..its nearly completed..
Should i try rooting it before flashing stock? I dont want to risk another brick cause of rooting
Click to expand...
Click to collapse
You don't have to root if you're flashing with QFIL.
How did you flash the QCN without root anyways?
Again, what network are you in?
theflyingrahul said:
You don't have to root if you're flashing with QFIL.
How did you flash the QCN without root anyways?
Again, what network are you in?
Click to expand...
Click to collapse
i followed this youtube video..
https://www.youtube.com/watch?v=1-4tmWvTGiI
i remember reading about it somewhere.. you only need to enable diagnostic mode to flash QCN, and many phones require root to enable this port, and some other need root to unlock to bootloader..
but k53a48 phones have unlocked bootloader and diagnostic mode port can be enabled easily like the guy in the youtube video..
(power off and press power button and volume up till a screen comes on and then connecting the USB, the PC installs the diagnostic port..
this is what i think happened.. i had zero errors during qcn flashing and i hope i didn't do it wrong?
I Have idea network if that is what you asked
The ROM download is complete..so i ll start flashing then?
guitargeek0517 said:
i followed this youtube video..
https://www.youtube.com/watch?v=1-4tmWvTGiI
i remember reading about it somewhere.. you only need to enable diagnostic mode to flash QCN, and many phones require root to enable this port, and some other need root to unlock to bootloader..
but k53a48 phones have unlocked bootloader and diagnostic mode port can be enabled easily like the guy in the youtube video..
(power off and press power button and volume up till a screen comes on and then connecting the USB, the PC installs the diagnostic port..
this is what i think happened.. i had zero errors during qcn flashing and i hope i didn't do it wrong?
I Have idea network if that is what you asked
The ROM download is complete..so i ll start flashing then?
Click to expand...
Click to collapse
It's correct that you have to enable only the diagnostic port to download QCN, but I'm not sure of the procedure that you describe here....
K6 Note doesn't come with an unlocked bootloader by default, you'll have to manually unlock.
I'm not sure of the technique that is shown in the video, the general procedure to open the diagnostic port is through adb. But if you are sure that the IMEI is flashed correctly, then there's nothing to worry about I guess.
Again, you're going to flash the S223 ROM using QFIL right?
Your network is fine, it's non-VoLTE, so calls should work if you have restored the QCN properly.
I m downloading the rom from a link in the description of a video..there were multiple stock files and i asked the youtuber and he told me download this one..
Lenovo_K6_Note_K53A48_K53_USR_S306_1709051329_Q00440_POLK_QPST
This is the one that i downloaded.. why are there so many stock files anyway? Is this right? Else
Would flashing stock using lenovo moto assistant application work?
Some people in xda had success using lenovo moto assistant..but the application asks for HW code and I cannot find my HW code from my sn number- HNB1GDX3 ,
No calls are not working, even ussd codes arent working..does that mean that even the qcn flash was done wrong ?:crying:
guitargeek0517 said:
I m downloading the rom from a link in the description of a video..there were multiple stock files and i asked the youtuber and he told me download this one..
Lenovo_K6_Note_K53A48_K53_USR_S306_1709051329_Q00440_POLK_QPST
This is the one that i downloaded.. why are there so many stock files anyway? Is this right? Else
Would flashing stock using lenovo moto assistant application work?
Some people in xda had success using lenovo moto assistant..but the application asks for HW code and I cannot find my HW code from my sn number- HNB1GDX3 ,
No calls are not working, even ussd codes arent working..does that mean that even the qcn flash was done wrong ?:crying:
Click to expand...
Click to collapse
Hello,
The file seems to be correct. You should install QPST and use it to flash the ROM file.
Lenovo moto assistant might work, I had no success with that though.
The QCN that you used might be probably dirty, I'd suggest you to reflash with QPST and try burning the QCN again. Generate a new QCN before you do.
Sir, I Did custom ROM flash for lenovo K6 note, with twrp and lineage OS 16, after completion of ROM flash, although I have IMEI number, wifi MAC address in about phone section
My problems to FIX:
------------------------
1) Need Volte support(VOLTE not supporting for my JIO SIM)
2) *#06# IMEI code not working(IT shows "Connection problem or invalid MMI code." although the IMEI numbers are available in About phone category under settings)
3) In settings Bluetooth address "Unavailable"
FayazD said:
Sir, I Did custom ROM flash for lenovo K6 note, with twrp and lineage OS 16, after completion of ROM flash, although I have IMEI number, wifi MAC address in about phone section
My problems to FIX:
------------------------
1) Need Volte support(VOLTE not supporting for my JIO SIM)
2) *#06# IMEI code not working(IT shows "Connection problem or invalid MMI code." although the IMEI numbers are available in About phone category under settings)
3) In settings Bluetooth address "Unavailable"
Click to expand...
Click to collapse
Hey FayazD,
What you've mentioned seems to be a common problem and I couldn't really find a fix.
1). VoLTE doesn't seem to work. Before writing this post (restoring the baseband), no other calls except VoLTE ones worked for me. After restoring the baseband, 3G/2G calls work and VoLTE doesn't work. I'm not sure if there is a fix for that.
2). This could probably be an issue with the ROM itself. Try to flash a different ROM, I recommend AEX, which I'm currently using and is very stable.
3). The Bluetooth address issue again is something which I observed in Lineage 16. It shouldn't affect the functionality, except for the changing Bluetooth address on every reboot. Not sure if it is an issue with the ROM itself, try AEX, this issue isn't present there. Again note that the Bluetooth address could be shown as "Unavailable" when Bluetooth is turned off.
Will update if there is a solution for the VoLTE thingy.
theflyingrahul said:
Hey FayazD,
What you've mentioned seems to be a common problem and I couldn't really find a fix.
1). VoLTE doesn't seem to work. Before writing this post (restoring the baseband), no other calls except VoLTE ones worked for me. After restoring the baseband, 3G/2G calls work and VoLTE doesn't work. I'm not sure if there is a fix for that.
2). This could probably be an issue with the ROM itself. Try to flash a different ROM, I recommend AEX, which I'm currently using and is very stable.
3). The Bluetooth address issue again is something which I observed in Lineage 16. It shouldn't affect the functionality, except for the changing Bluetooth address on every reboot. Not sure if it is an issue with the ROM itself, try AEX, this issue isn't present there. Again note that the Bluetooth address could be shown as "Unavailable" when Bluetooth is turned off.
Will update if there is a solution for the VoLTE thingy.
Click to expand...
Click to collapse
In AEX the VOLTE will work or not, if you give me the assurance i'll flash with AEX
Hi guys,
I have Pocophone f1 Global version (M1805E10A) 6gb RAM 64gb storage). I had a problem about IMEI and tried to fix it. Finally i fixed it, but now when i insert the sim card, phone recognises the sim card, asks me pin code. No problem till here. After entering pin code, phone unlocks but there is no service all the time. When i try to make a call it says "Turn off airplane mode to make a call." and "RADIO OFF" in the screen, as i marked in the photo.
In the Hardware Test section (*#4636#*#*) yes detect.
What i did for fixing;
1. Flashed china developer rom; did not work,
2. Flashed global developer rom; did not work,
3. Flashed NON-HLOS.bin file from gobal developer rom via fastboot adb; did not work,
4. Flashed gobal stable rom; did not work,
5. Flashed NON-HLOS.bin file from gobal stable rom via fastboot adb; did not work,
6. Tried to flashed .qcn file from another Redmi Note 4 Global version but get an error on this and could ot do this,
7. Flashed RR rom by TWTP, clean flash; didn't work,
8. Flashed latest developer rom from xiaomi.eu; didn't work.
I show about phone section for my phone at the picture too. I have bootloader unlocked, no root access for now (i had before and can get easly)
Please help...
I can't upload photos because I'm a beginner
Thanks
E-MAIL: [email protected]
wesleyned said:
Hi guys,
I have Pocophone f1 Global version (M1805E10A) 6gb RAM 64gb storage). I had a problem about IMEI and tried to fix it. Finally i fixed it, but now when i insert the sim card, phone recognises the sim card, asks me pin code. No problem till here. After entering pin code, phone unlocks but there is no service all the time. When i try to make a call it says "Turn off airplane mode to make a call." and "RADIO OFF" in the screen, as i marked in the photo.
In the Hardware Test section (*#4636#*#*) yes detect.
What i did for fixing;
1. Flashed china developer rom; did not work,
2. Flashed global developer rom; did not work,
3. Flashed NON-HLOS.bin file from gobal developer rom via fastboot adb; did not work,
4. Flashed gobal stable rom; did not work,
5. Flashed NON-HLOS.bin file from gobal stable rom via fastboot adb; did not work,
6. Tried to flashed .qcn file from another Redmi Note 4 Global version but get an error on this and could ot do this,
7. Flashed RR rom by TWTP, clean flash; didn't work,
8. Flashed latest developer rom from xiaomi.eu; didn't work.
I show about phone section for my phone at the picture too. I have bootloader unlocked, no root access for now (i had before and can get easly)
Please help...
I can't upload photos because I'm a beginner
Thanks
E-MAIL: [email protected]
Click to expand...
Click to collapse
I have same problem what you have right now and it has been over 6 months where still can't find a fix, unfortunately no one , if you fix the problem, plz inform me too. My email: [email protected], good luck bro
Heamnath said:
I have same problem what you have right now and it has been over 6 months where still can't find a fix, unfortunately no one , if you fix the problem, plz inform me too. My email: [email protected], good luck bro
Click to expand...
Click to collapse
i also have the same problem.its a hardware issue..the radio module is damaged which comes pre attatched with the main board.i visited service center they told i had to replace mainboard which cost around 11k.better buy a new phone instead.but the phone is working absolutely fine only the signal is not coming.
I also have similar problem. Constant wifi and mobile service droping. On MIUI 11 and Lineage 17.1(custom rom not helped). Maybe someone will answer on this problem?
Hi there,
May be you already did this. But out of curiosity wants you to know that you can try this if not yet done. May be your phone network come back Alive.
Go to settings > my device > all specs > internal storage
Click on this for couple of times 3 to 4 times.. then you will be entering phone information.
Select phone information 1 and turn on mobile radio power button there. Like wise for the other sim. May be it's turned off there and is the reason for the problem.
I am sorry if it didn't help. Anyway keep trying until you succeed is the secret. Thanks
Cheers
sssyraj
wesleyned said:
Hi guys,
I have Pocophone f1 Global version (M1805E10A) 6gb RAM 64gb storage). I had a problem about IMEI and tried to fix it. Finally i fixed it, but now when i insert the sim card, phone recognises the sim card, asks me pin code. No problem till here. After entering pin code, phone unlocks but there is no service all the time. When i try to make a call it says "Turn off airplane mode to make a call." and "RADIO OFF" in the screen, as i marked in the photo.
In the Hardware Test section (*#4636#*#*) yes detect.
What i did for fixing;
1. Flashed china developer rom; did not work,
2. Flashed global developer rom; did not work,
3. Flashed NON-HLOS.bin file from gobal developer rom via fastboot adb; did not work,
4. Flashed gobal stable rom; did not work,
5. Flashed NON-HLOS.bin file from gobal stable rom via fastboot adb; did not work,
6. Tried to flashed .qcn file from another Redmi Note 4 Global version but get an error on this and could ot do this,
7. Flashed RR rom by TWTP, clean flash; didn't work,
8. Flashed latest developer rom from xiaomi.eu; didn't work.
I show about phone section for my phone at the picture too. I have bootloader unlocked, no root access for now (i had before and can get easly)
Please help...
I can't upload photos because I'm a beginner
Thanks
E-MAIL: [email protected]
Click to expand...
Click to collapse
How he managed to repair the imei. I haven't found a solution yet. Help me please.
Hi to everyone..Had the same problem, phone was wet previously. Took it to service (not Xiaomi's). They changed the charging port and told me that the radio is on the same component. After the change signal is like before, everything working great. Hope this helps someone..
dreamdrake said:
Hi to everyone..Had the same problem, phone was wet previously. Took it to service (not Xiaomi's). They changed the charging port and told me that the radio is on the same component. After the change signal is like before, everything working great. Hope this helps someone..
Click to expand...
Click to collapse
Hi, my wifi and bluetooth work, replacement usb charging board is next to nothing, is this all service replaced?
hecatae said:
Hi, my wifi and bluetooth work, replacement usb charging board is next to nothing, is this all service replaced?
Click to expand...
Click to collapse
Yes, but it lasted just ten days..Then burned a capacitor on the motherboard and phone was dead.
dreamdrake said:
Yes, but it lasted just ten days..Then burned a capacitor on the motherboard and phone was dead.
Click to expand...
Click to collapse
And this is why I may just give up on my f1, after replacing the volume buttons I just do not trust the handset anymore.
Hello i try one days ago crossflash my phone because its not be posible used in Czech republic (calling,data). But my phone stuck in EDL mode. Display its just blank black screen nothing more. If i connect phone to QFIL . Qfil see my phone, but if i try make recovery via xml raw program file (which i used from another version TM etc, dont find for Verizon) After click to download ..coming many news about Sahara "failed"... Do you have any solution ?
lukasbudai said:
Hello i try one days ago crossflash my phone because its not be posible used in Czech republic (calling,data). But my phone stuck in EDL mode. Display its just blank black screen nothing more. If i connect phone to QFIL . Qfil see my phone, but if i try make recovery via xml raw program file (which i used from another version TM etc, dont find for Verizon) After click to download ..coming many news about Sahara "failed"... Do you have any solution ?
Click to expand...
Click to collapse
I've always had to reboot edl after connecting to qfil
Thank you , your help me help. But now i stuck in FACTORY RESET 2. Beacose i lost my imei (but physicly i stil have original in the box.) Its any idea how to repair my old imei ? Thank you.
lukasbudai said:
Thank you , your help me help. But now i stuck in FACTORY RESET 2. Beacose i lost my imei (but physicly i stil have original in the box.) Its any idea how to repair my old imei ? Thank you
Click to expand...
Click to collapse
Check this thread, I think they solved this problem
[V600AM][GUIDE] How to crossflash your AT&T V60
Crossflash guide for AT&T LG V60 Firstly I wanna give a special thanks to DK and @kim12355 (Mama Tao), without them this guide wouldn't be possible. Also great thanks to all guys on the Telegram Group. This guide was based on tbl-locksmiths's and...
forum.xda-developers.com
ebowen 747 said:
Check this thread, I think they solved this problem
[V600AM][GUIDE] How to crossflash your AT&T V60
Crossflash guide for AT&T LG V60 Firstly I wanna give a special thanks to DK and @kim12355 (Mama Tao), without them this guide wouldn't be possible. Also great thanks to all guys on the Telegram Group. This guide was based on tbl-locksmiths's and...
forum.xda-developers.com
Click to expand...
Click to collapse
I check but its can be stil big problem because i dont make backup LUN5 ? But stil have my original SN and imei in BOX. Its possible write my IMEI to in to file LUN5 ? ...
lukasbudai said:
I check but its can be stil big problem because i dont make backup LUN5 ? But stil have my original SN and imei in BOX. Its possible write my IMEI to in to file LUN5 ? ...
Click to expand...
Click to collapse
It is with a hex editor but I've never done it
And now after many times edl mode, phono no response with pc ?... No sound connected with pc, nothing in Device manager ? Do you think its gone ?
Now my phone its be unbricked, i reload my own imei via OCTOPLUS, and no now have problem with call ? Data conection work excelent and fast via LTE,but if i try make call then my phone try change network, just dialing after few moments hangs up. ... I have crossflash phone VM-->to TM--> EU (A12) region POL. I try update modem_a via qfil, but stil not work correct and finger print now working.
lukasbudai said:
Now my phone its be unbricked, i reload my own imei via OCTOPLUS, and no now have problem with call ? Data conection work excelent and fast via LTE,but if i try make call then my phone try change network, just dialing after few moments hangs up. ... I have crossflash phone VM-->to TM--> EU (A12) region POL. I try update modem_a via qfil, but stil not work correct and finger print now working.
Click to expand...
Click to collapse
DId you try repairing IMEI using service code *#546368#*Model Number#
NaughtyDescent said:
DId you try repairing IMEI using service code *#546368#*Model Number#
Click to expand...
Click to collapse
Yes this I try but IMEI don't write in system..just in Hidden app.
lukasbudai said:
Yes this I try but IMEI don't write in system..just in Hidden app.
Click to expand...
Click to collapse
After I go again to hidden menu, then again see IMEI null, this why I take Octopus repair IMEI...
lukasbudai said:
After I go again to hidden menu, then again see IMEI null, this why I take Octopus repair IMEI...
Click to expand...
Click to collapse
That will cost you credits. Usually this menu works for me in A10. You can recover your IMEI by downgrading to android 10. backing up Lun 5 partition and restoring after updating to your desired ROM. May be That works. But Octoplus is easy way xD
NaughtyDescent said:
That will cost you credits. Usually this menu works for me in A10. You can recover your IMEI by downgrading to android 10. backing up Lun 5 partition and restoring after updating to your desired ROM. May be That works. But Octoplus is easy way xD
Click to expand...
Click to collapse
Wau this I don't, work just in A10 I have A11 and A12, A10 I don't try..good idea for next mistakes Yes it's cost credit but it's worth for using phone..
NaughtyDescent said:
That will cost you credits. Usually this menu works for me in A10. You can recover your IMEI by downgrading to android 10. backing up Lun 5 partition and restoring after updating to your desired ROM. May be That works. But Octoplus is easy way xD
Click to expand...
Click to collapse
I write you pm...please look in box.