Hi there i have Tecno Spark KC2.
Yesterday i was trying to bypass FRP. By mistake i used Miacle Box. And after that my mobile is dead.I think it is hard bricked. I am unable to Turn on and these is no charging sign when pluged it. I tried to flash stock rom using sp flash but no luck. It detects my port MediaTek Port but show an error "status brom cmd start cmd fail".
Is there any solution?
Related
Hi,
can someone help me unbrick an x401?
I tried to flash an original firmware provided by manufacturer, but it doesn't work.
Phone can connect to win7 and COM port persinstenly appears in device manager while running SP flash tool which at the end says: "download complete"
But it still doesn't boot and show only white screen when connected via USB cable.
Any suggestion?
Hello Everyone
I need help for micromax A116 totally wasted not getting start no Led Notification for charging and when usb cable or battery is connected flash light flashes for a second and nothing after that tried MTK Droid tool, also tried to flash the mobile with SP flash tool and nothing is working out getting Error on every tool please someone help me to get the recovery installed on it so that u can install stock rom and after that root it and get the custom rom installed . Please Help its urgent
HARD BRICKED phone with no sign of charging LED light or anything. After that when you tried to flash your stock ROM back on the device using SP TOOLS then you get the error written:
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) "
this is the error message i am getting every time i am trying to flash with SP tool
luvlastcall said:
HARD BRICKED phone with no sign of charging LED light or anything. After that when you tried to flash your stock ROM back on the device using SP TOOLS then you get the error written:
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) "
this is the error message i am getting every time i am trying to flash with SP tool
Click to expand...
Click to collapse
Refer this
http://forum.xda-developers.com/showthread.php?p=45382917#post45382917
it may help and post shows for other mobile but it works for a116.
I tried pressing vol+ or vol- while connecting USB then only it will detect and rom gets flashed.
But there is chance that after flashing device may boot and works like normal and suddenly it may become like brick and you may have to try this method again to flash.
my mobile Micromax a116 was also facing same problem i was flashing repeatedly whenever it becomes like brick. one day i took it to service center when it was in brick state and they sent it to Delhi as local guys not able to fix and confirmed Mother board failure. I got new mother board installed freely at that time it was in warranty period and till date its working fine. currently i am using Discovery Rom
Hi..
I Have a problem with my Acer Liquid E2 Dual Sim..
Before this, my problem is the phone was stuck in the Ace green logo (Bootloop) and i tried to flash it using SP flash tool, and it flashed succesful until the green circle, but my device gotten even worse, now when i turn on the power, it just vibrate once and continue in blank screen only..and when i try to connect it to the pc, it recognize with a vibrate and blue led turning on, but in the device manager, it detects as MTK USB Port, the is no MTK Preloader or any driver except the mtk usb port
I already googled it, and it seems because i flashed the wrong preloader (it means i used the wrong firmware in the spflashtool), but i downloaded it from the global acer download, And another information i get that my device is in a condition where it enters the low-layer download interface of the MT65xx device (AFAIK).. Thats why it only detects as MTK USB Port. So what to do now? I have tried using SPFlashTool to Dwonload only the preloader checked using from two different rom, but no success both? already tried any different version spflashtool
Every time i tried to download the preloader to the device using spflashtool it just shows "dram failed"
like this
"BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!"
Does anyone knows how to fix it
Anyboy can help me pleaasee
lukerodriguez said:
Anyboy can help me pleaasee
Click to expand...
Click to collapse
i have same problem bro, is your phone already fix?
I bricked my phone and it is not getting started. I have tried all the possible way explained in different forums but no luck. I have downloaded the stock rom and tried to flash using YGP tool. But my device is not getting detected by windows properly. It will get connected for a 2 seconds and will get disconnected. While getting connected I can see the mediatek device in the port (device manager) and it goes off on disconnection. I there any other way to flash the rom than YGP tool. Is it possible to get SP flash tool rom for A109.. Please help
Experts please help me. My phone is detecting SP Flash tool. So please help me to get the sp flash tool rom
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Tomaskaos said:
Hello.
Everything has gone terribly wrong for my phone and I desperately need your help.
I downloaded what was stated on needrom.com I made sure MTK vcom was installed properly and had the correct rom from needrom.com but I still got Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP flash when using MTK_AllInOne_da.bin.
I then tried DA_PL.bin and got another error. I tried to uncheck preloader and run Download through SP flash with DA_PL.bin which worked just fine. However now I'm stuck at the Bluboo logo screen and phone does not load into android.
I still get Brom Error: STATUS_BROM_CMD_SEND_DA_FAIL in SP Flash if I use MTK_AllInOne_da.bin but if I use DA_PL.bin now I get this error:
Chip mismatch!
Scatter:MT6757D
device: MT6757
Please help me, my phone is bricked until one of you help me. I'd be forever grateful!
Click to expand...
Click to collapse
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
SubwayChamp said:
Don`t worry about that, first this is the link of the last update https://www.google.com/url?q=https:...ds-cse&usg=AFQjCNFJKeEcDClPU2MnxLJefaQ19GmQpQ
for more success put your folder of SPFlash Tool near to folder of your unpacked rom (for short transmission of data) and Bluboo S1 has a few different way to enter to other mtk cause battery it`s not removable like other just disconnect it and connect again; in this case connect cable usb to your device, prepare all the files in SPFlashTool and click download and now while pressing both volume + and - connect cord to pc till SPFlashTool begin to recognize files (red letters) and release now, SPFlashTool continues process till 100% in yellow progressing line
Click to expand...
Click to collapse
Thanks!!! It works!!!!
Just be very careful. The USB C connector port in the phone is very loose... so make sure you can hold the cable tight other wiser it will lose the connection and brick your phone. For me, I had to remove the Plastic cover to be able to hold the power cable tight!
Hi, could you help me please? I did your steps, but it is not working. Sp flash does all its job, shows the green sign, but the phone stills dead. What I noticed the usb connects with the phone, then it disconnects. I tried to install the drivers as the tutorials say like deactivating the driver signature enforcement, but nothig happens well.