Good day. The phone LG G3 VS985WK worked, but the Internet distribution via the SIM card of another operator was not available. I used a program SALT FWUL loaded from a USB flash (Live USB) drive to remove AntiRollBack. Through the inoperability of the Internet distribution, I also deleted the system partitions using the program SALT FWUL loaded from a USB flash (Live USB). After that, the program SALT FWUL does not detect the device, recovery does not start and no Download Mode. Moved the phone to Qualcomm HS-USB QDLoader 9008. When restoring the phone with the program BoardDiag (AP Check), an error appears "No response from the device. Check PMIC first and if stiil boot problem, replace AP". If you choose settings AP Check+EMMC Test or PMIC ON, then "Device was not found in dload trying flash programmer". Settings B2 (MSM8974AC) or G2 (MSM8974) and versions BoardDiag 2.99a or BoardDiag 3.99c do not affect, the error is the same.The program https://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-g2-all-variants/ restores the phone, but only one port LGE AndroidNet USB Serial Port and one modem LGE AndroidNet USB Modem appears. I use Windows 7 SP1 Ultimate x64. Please help me recover the phone. I understand Russian and English.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Buy a new phone m8. VS985 are cheap.
Related
**************Flashing Hard Bricked Redmi 3 SnapDragon***********
This IS the Guide to Flash hard Bricked Redmi 3, using Deep flash mod, No Fastboot, No Edl, No Test point, very easy and simple, Hit :good: if this helpful for you,
Instructions-
First of all Prepare Deep Flash Cable using Below Guide
Attached Both Coper Wire and then connect this cable with your pc
Now connect your Device to usb [Make Sure Your phone is switched Off]
On Pc go To Device manager and Look on port, {No Available] Don't Worry]
Pull the attached Wire and look Device Manager a New port Is Available HS-USB Diagnostic 9008[ com5, com17 etc]
Ok your Device is ready For Flashing
Run mi Flash click on Browse and Load Fastboot Rom Folder
Click Refresh and Then Flash Done, wait a few Seconds While flashing IS complete ,
Done,
Bought a Deep Flash Cable @ AliExpress (for about 5€/5US$). It has a button to enable Qualcomm HS-USB QDLoader 9008 and for me is more secure then trying to risk to kill your mainboard via USB.
P.S.: I'm not good at DIY.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
plz sent me a cable at my village, lol, Delivery system Not Available For all Areas or this guide for that person,
Does this work with Redmi Pro?
Hello.
I have one old Lenovo with MT6582M , which has 1gb ram and 4rom, which i flashed with stock rom using SP flash tools. After that phone was in bootloop, then tried to reflash but got error with checksum that recovery image isn't same size. And then i realize there is no recovery mode.
Next i format all data, and flash again, all went OK. But phone won't power on anymore, no charging, nothing...
PC recognizes it as 3 different ports, it depends on how i connect it (with ,without battery or vol key pressed) : Mediatek preloader USB VCOM (Android) , ADrom port , and MediaTek USB port
I tried 3 STOCK roms from different sites, flashing process has no issues, but phone still can't turn ON. But if i check DA DL all with chksum, after flash i get this error:
Brom error: chksum_error (1041)
Tried to flash only boot, after that whole rom again, tried to firmware upgrade but got Error: Failed to get PMT info.
I tried many versions of SP flashtool, and the older ones show me this 29Gb+8gb in statusbar, which i can't say how happened, but it seems PMT-partition memory table , has some problems.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Does someone has any ideas for me ?
Hi , I think I probably f*kc up something. My sister just changed his phone to a new one so I borrowed his old Lg K7 x210 3G (I just post all the info I have about the model cause I don't really know exactly which one is) Well I unloaded the Bootloader and tried to change the recovery. I fallowed the steps of the guide but at the end I finished having the "No Command" error . This got me nervous and I started to touch things without knowing what I was doing (really, REALLY bad idea )
So the phone got stuck on a bootloop , well time to flash to get rid of the loop. The main problem is that I can't flash anything (except for the preloader) because it disconects all the time. I installed 20 different drivers and Sp Flash Tools versions (erasing the old ones with USBDeview )
These are the two states that jumps every 2 seconds.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
What can I do to avoid this "jumps" and flash the rom correctly to the phone?
I tried 2 different pc , all the ports in this pc and all the cables I could find at home
PS: This are the different guides and tutorials I tried but failed.
https://forum.xda-developers.com/showthread.php?t=1982587 (It can't connect to the lg app because the "jumping" issue )
https://forum.xda-developers.com/elephone-m2/help/windows-10-mtk-vcom-usb-drivers-32-64-t3267033 (Tried these on a W10 computer but again the device cant stay connect for more than 2 seconds )
https://www.youtube.com/watch?v=A3TmXtOA0IA
Thanks for your help . I don't want to give so early I think it could be fixed.
So, my lg g5 h850eu one day started turning on and off when finally show screen like this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
.
So i downloaded minimal adb and fastbooot and typed "fastboot reboot". After this commend phone turned off and never displayed anything. In device manager show qualcomm hs-usb QDLoader 9008 (com3) and in minimal shows error: no devices/emulators found. I wanted use lgup to flash stock firmware but shows no handset connected.
What can i do in this situation?
Unfortunately, this isn't possible to fix this in my experience since the firehose and required program and rawprogram0.xml files do not work with the G5. The only solution is to replace the motherboard.
najak223 said:
So, my lg g5 h850eu one day started turning on and off when finally show screen like this
.
So i downloaded minimal adb and fastbooot and typed "fastboot reboot". After this commend phone turned off and never displayed anything. In device manager show qualcomm hs-usb QDLoader 9008 (com3) and in minimal shows error: no devices/emulators found. I wanted use lgup to flash stock firmware but shows no handset connected.
What can i do in this situation?
Click to expand...
Click to collapse
The same thing happened to me yesterday. First the stock camera started to hang, clearing data solved that, but at night it began to restart until the "fastboot" escreen appeared. Then I removed the battery, put the reserve one (a new one) and it never gave again a life signal...:crying:
Hello,
I hope someone can offer an idea of how to solve issue I'm facing atm.
I have FZ-X1 phone and it's came simlocked from Japan.
I want to run "fastboot oem clearsimlock 0".
I'm trying to communicate to it using fastboot but the problem I have is that once I boot the phone into its stock bootloader, my PC cannot see connected phone in Device Manager:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Once phone is fully booted into UI, I can see it recognised running command "adb devices":
I tried both latest Google and original Panasonic ADB drivers available for download. I use Windows 7 x32 version - it shouldn't have issue with drivers signature, right?
Have no clue how to overcome this obstacle. Any ideas or suggestions are very appreciated.
Thanks!
Remove the Google USB driver and the Panasonic ADB driver: All you have to do is to install the proper OEM USB driver suitable for your device:
Download Qualcomm HS-USB QDloader 9008 driver for Windows - 32-bit / 64-bit
You can now download Qualcomm QDLoader HS-USB Driver of 32-bit & 64-bit Installer. We have put up the entire installation process for you.
www.getdroidtips.com
Thank you for your reply! I tried that - unfortunately the phone still not detected by Windows 7 once connected to PC.