NOTE: Will just clarify, probably am an idiot and messed up a simple thing, so please do take everything I say here with a grain of salt.
The phone was rooted with Magisk v25.1, and I had also installed the unofficial TWRP from this very forum. I also believe I was on 11.0.4.0 of OxygenOS. It is the factory unlocked version.
I was following a guide to update the phone through fastboot, since stock recovery was just showing a screen with a keyboard, which appeared to be impossible to get past. Said guide is here.
Linked in the guide above is the 8th step of that guide, where you then flash the files from the OTA file after extracting them with payload_dumper. I believe the version I was extracting was 11.0.7.0, but to be honest, it was whatever I downloaded off of the Oxygen Updater app, so I'm not entirely certain. I had installed "boot.img", "dtbo.img", and "modem.img", then getting to "abl.img", before receiving an error: Flashing is not allowed for Critical Partitions. "Well," I thought, "I suppose I just can't do it then. *shrug*. Back to this version of OxygenOS I go." That was before remembering to attempt doing "fastboot flashing unlock_critical", which, gave me: Device already unlocked! Well, clearly not, as I should've been able to write abl.img. Attempting to flash again gave me nothing, so, I said screw it.
Well, upon trying to hit start in fastboot, I noticed the phone were now bootlooping back to fastboot over and over. So, I'm lead to a few conclusions:
a) I'm gonna need "dtbo.img" and "modem.img" (I already have boot.img) from the 11.0.4.0 stock image. I cannot find the actual image, so I'm lead to now needing some help here.
b) There has to be some way to continue flashing the files in fastboot (that is, if that is the correct course of action; I am assuming, please feel free to correct me).
c) There is a different way to fixing this than I am thinking.
d) Worst case scenario, this thing has to go back to OnePlus.
Would really hate to have to get to Step D, as this phone was a birthday present to me, and I'd find it wholly embarrassing to throw my hands up in the air a single day after getting the damn thing for my birthday just to need to send it back already, but if nobody can help me out here, then that's where I'm at.
Would appreciate any and all help/suggestions! Thanks.
EDIT: Phone is stuck in Qualcomm Crashdump mode now, bootable into fastboot with vol up+down+power. Looks like it's irreparable. Already working with OnePlus to get it replaced.
EDIT 2: Fixed it!! Big thanks to this thread for the help.
1)get a usb otg and pendrive
2)download and tranfer pixel experience full build zip file in you pendrive
3)go to fastboot and flash twrp recovery misc and vbmeta and boot to recovery
4)insert pendrive in usb otg and connect it to phone
5)click on install then click on select storage usb otg and flash the pixel experience like you flash other files
6)reboot the phone
7)after setting up download the rom you want to and go to fastboot then flash twrp again 3rd step
8)flash the rom you want to install and flash g-apps reboot your phone
9)complete all steps and you have your phone with custom os/rom
Raghaov said:
1)get a usb otg and pendrive
2)download and tranfer pixel experience full build zip file in you pendrive
3)go to fastboot and flash twrp recovery misc and vbmeta and boot to recovery
4)insert pendrive in usb otg and connect it to phone
5)click on install then click on select storage usb otg and flash the pixel experience like you flash other files
6)reboot the phone
7)after setting up download the rom you want to and go to fastboot then flash twrp again 3rd step
8)flash the rom you want to install and flash g-apps reboot your phone
9)complete all steps and you have your phone with custom os/rom
Click to expand...
Click to collapse
No offense, but this is a pretty dumb response. I don't think you're very familiar with how TWRP is on this device, nor the state of my own. I cannot mount storage, and even if I could, I don't even believe this rom exists for the N200 5G. Along with that, why would a USB OTG be necessary when there's.. I don't know, an SD card slot that works fine and is readable?
Also step 3 is a little laughable. That's why I'm even here in the first place; I couldn't flash every damn thing!
I'll share Oxygen OS 12 if you want it, and let me know if I should keep searching.
Just use payload dumper go to dump the payload and then flash the files with this guide.
Edit: Uploading it via xda didn't work, so here's the google drive link.
justauserthatusesaphone said:
I'll share Oxygen OS 12 if you want it, and let me know if I should keep searching.
Just use payload dumper go to dump the payload and then flash the files with this guide.
Edit: Uploading it via xda didn't work, so here's the google drive link.
Click to expand...
Click to collapse
Do you have one for metro T-MO variant?
Tyreethetruth said:
Do you have one for metro T-MO variant?
Click to expand...
Click to collapse
Nope, I also don't know how to get it, unfortunately.
sounds to me like you dont want a real answer i mean at least respect the one person that replied to your post, not our fault you got yourself in this situation.
Related
Hi all, well I think I have all but wrecked my 16gb shield tv. I unlocked bootloader, installed twrp and rooted, all was working fine. Then I decided to flash the full android rom that is on the forum . before doing so, i used twrp and made a backup. I installed the full android rom, although it seemed to work fine, i was not crazy about it and decided to go back to the original OS, so I booted up in twrp and went to the restore function, there were no backups to restore , I guess when I installed the system img for the full android it erased my backup somehow. anyway, I next went to nvidia website and downloaded the restore image for the 16gb shield tv, i booted in to bootloader and was following the instructions to restore the shield. all seems to go fine until I try to flash the system img, then I get the error "invalid sparse file format at unknown block 0000" it tries to continue but fails, afterwards the system will not boot at all, I can get back to twrp recovery an flash the full android rom just fine, but am not able to flash back the original os without that error. any suggestions would be greatly appreciated, as I am stuck at this point as what to attempt next. thanks. Here is a pic of the errors i am getting.
Use a windows pc or the last fastboot version from android sdk or a better otg cable.
Is just a connection problem or the extracted system.img was corrupted when extracted.
If you not solve download again the stock firmware and unzip with a decent tool. Is possoble that when you extracted the archive your stock system.img was corrupted.
I flashed my Shield a million times with no problem. Also the ridiculous stock firmware just to do some logcat.
Shield Console is solid as a rock, you can do anything.
Thanks for the reply zulu, I will re download the img and try again, although I'm concerned something is wrong with the partition, as I was able to flash the full android rom, but now can no longer flash it either. I will let you know the results as soon as I'm able to retry.
cdsn99 said:
Thanks for the reply zulu, I will re download the img and try again, although I'm concerned something is wrong with the partition, as I was able to flash the full android rom, but now can no longer flash it either. I will let you know the results as soon as I'm able to retry.
Click to expand...
Click to collapse
Don't worry all is ok. I'm here to help you step by step if necessary.
my friend had a problem like this with another device, another firmware. He used a MAC OS to extract the firmware, and the system.img was not extracted well.
What are you using ? MAC, Windows, Linux ? what is your fastboot version ? do you use an usb otg cable ? what is your precise procedure to go in the bootloader ?
i use an usb otg cable to use fastboot from my PC.
to go in bootloader, I connect the usb otg cable to Shield, that is already connected also to my PC usb port, after i insert the power cable to Shield, and after i press quickly the power button for 5 seconds.
From Windows, if i try to install with the normal micro usb cable (exspecially the one that come with Shield), i have problems similar to your problem.
you can try also to install only the stock system.img to see what happen.
fastboot flash system system.img
fastboot -w (this clear user data, but is necessary when you switch from a firmware to another)
fastboot reboot
i installed the stock and the full Android many many times. If the Shield resist to me, can resist to all
zulu99 said:
Don't worry all is ok. I'm here to help you step by step if necessary.
my friend had a problem like this with another device, another firmware. He used a MAC OS to extract the firmware, and the system.img was not extracted well.
What are you using ? MAC, Windows, Linux ? what is your fastboot version ? do you use an usb otg cable ? what is your precise procedure to go in the bootloader ?
i use an usb otg cable to use fastboot from my PC.
to go in bootloader, I connect the usb otg cable to Shield, that is already connected also to my PC usb port, after i insert the power cable to Shield, and after i press quickly the power button for 5 seconds.
From Windows, if i try to install with the normal micro usb cable (exspecially the one that come with Shield), i have problems similar to your problem.
you can try also to install only the stock system.img to see what happen.
fastboot flash system system.img
fastboot -w (this clear user data, but is necessary when you switch from a firmware to another)
fastboot reboot
i installed the stock and the full Android many many times. If the Shield resist to me, can resist to all
Click to expand...
Click to collapse
Hi Zulu, thanks for the help, I don't have an otg cable, I just use the cable that came with the shield tv. Anyway, you were right, i re downloaded the image and all flashed well, who would have thought. wow, thanks so much for the info, hopefully I won't screw it up again. I like exploring new roms, but panic when I mess things up, I have been trying to re flash this thing for days, with all partitions flashing fine except for the system partition, anyway, downloading the new file must have fixed it , I also went into factory recovery and did a factory reset, maybe that had something to with it also, i really don't know. anyway, thanks again for your assistance.
cdsn99 said:
Hi Zulu, thanks for the help, I don't have an otg cable, I just use the cable that came with the shield tv. Anyway, you were right, i re downloaded the image and all flashed well, who would have thought. wow, thanks so much for the info, hopefully I won't screw it up again. I like exploring new roms, but panic when I mess things up, I have been trying to re flash this thing for days, with all partitions flashing fine except for the system partition, anyway, downloading the new file must have fixed it , I also went into factory recovery and did a factory reset, maybe that had something to with it also, i really don't know. anyway, thanks again for your assistance.
Click to expand...
Click to collapse
I'm at disposal. Thanks also to you to report back to me.
cdsn99 said:
Thanks for the reply zulu, I will re download the img and try again, although I'm concerned something is wrong with the partition, as I was able to flash the full android rom, but now can no longer flash it either. I will let you know the results as soon as I'm able to retry.
Click to expand...
Click to collapse
I had that issue before in a different device. The recovery had botched formatting the system partition. I tried to sideload the whole operating system, but in the end I just had to boot the recovery and format system again. It fixed my problem.
tooandrew said:
I had that issue before in a different device. The recovery had botched formatting the system partition. I tried to sideload the whole operating system, but in the end I just had to boot the recovery and format system again. It fixed my problem.
Click to expand...
Click to collapse
Yea I've experienced that too, I think the last time it happened it was on my Nexus 6. Try and execute this while in fastboot fastboot format system and then reflashing the system image.
This is basically a copy of my Z380M TWRP thread adopted for the ZenPad 10. I decided to start a new one since the OP of justshaun's original recovery/rooting thread has gone stale, even as I had posted several new releases of TWRP over the months. Its instructions are also a little outdated. I've also compiled a version for the new Z301M(F) models and needed a place to post it. This is where I will be posting TWRP updates from now on.
In addition to this thread, referring to the Z380M TWRP thread and the original Z300M thread (links above) may be helpful. These models share the same hardware and software base, so most things that apply to one tablet also apply to the others.
DISCLAIMER
As usual, you do anything described in this post at your own risk. No one but you is responsible for any data loss, bricking or damage of your device.
REQUIREMENTS
Windows or Linux PC
SP Flash Tool version 5.1532 (only this version will bypass security checks)
MediaTek VCOM drivers (available through Windows Update)
ZenPad 10 scatter file for SPFT, attached (choose the one for your tablet)
Recovery image, attached (choose the one for your tablet)
ZenPad Z300M, Z301M or Z301MF tablet upgraded to Android N
This won't be a guide on how to use SP Flash Tool. There are plenty of good guides out there like this one on how to set up drivers, load scatter files, flash and make backups with SP Flash Tool. If you're not familiar with this software or how to flash MediaTek devices in general, please do your research before attempting this. I will just get straight to the specifics about the ZenPad 10.
FIRST TIME INSTALLATION
For a locked bootloader:
At this point you should have your tablet powered off, the drivers installed, all of your data backed up, and SP Flash Tool v5.1532's Download tab open and loaded with the tablet's scatter file. Open the download agent file DA_PL.bin, replacing the default MTK_AllInOne_DA.bin. (You can use the AllInOne DA if you want, but the procedure involves extra steps as described below.) Load the extracted TWRP recovery image for your device (twrp-3.2.1-0-z30*m.img) under the recovery partition line in the partition table. Click the Download button inside SPFT. Now just connect the USB cable to your tablet and your computer's USB port. It should start the download process automatically and disconnect when finished.
Alternative Method:
If you're using MTK_AllInOne_DA.bin, you have to hold the Volume Up key as you insert the cable, which puts the device into an emergency download mode. In addition, you will need to have the stock preloader*.bin file loaded inside SPFT for it to be able to communicate with your tablet. The preloader is available inside the official zip file download. Do not flash the preloader (untick the box) or any partitions other than recovery. You just need to have a valid bin file selected under the Preloader line.
For an unlocked bootloader:
If you have used the Asus unlock tool to unlock your device, you will still not be able to use fastboot flash to install a custom recovery. However, you can do a "hot boot" or a tethered boot of TWRP. This method doesn't require SP Flash Tool. Download the TWRP image, put your tablet in fastboot mode and connect to PC. Then run this command to boot TWRP dynamically:
fastboot boot twrp-3.2.1-0-z30*m.img
Once inside TWRP, flash twrp-3.2.1-0-z30*m.img to Recovery using Install -> Install Image. Then reboot to recovery. You may be able to use TWRP in the tethered boot mode, but that could result in glitches due to different parameters passed by the bootloader to the kernel. That's why flashing is recommended.
To update from your installed TWRP version to a new one, just transfer the image to your tablet, then boot to TWRP and install it by going to Install -> Install Image and flashing to Recovery.
START RECOVERY
With the tablet powered off, hold the Volume Up and Power keys together until you get to a menu where you can select "recovery". On the Z301M/Z301MF, that option is labeled Factory Reset. Use Vol. Up to scroll and Vol. Dn to select. If you have a locked bootloader, it will show a Yellow State message because the recovery is not signed by the OEM. Just press volume up to boot it. On the welcome screen of TWRP it will ask you about modifying the system partition, I suggest you go with Keep System Read-only. Doing otherwise will complicate your OTA updates.
WARNING: Never start the stock recovery from the bootloader menu on this device. It is programmed by the bootloader to instantly wipe your data without any warning. Also, be aware that Android installs the stock recovery at every normal boot cycle. So you either have to flash the TWRP every time you want to run it, or disable the automatic recovery installation in the stock firmware. Any kind of mod to the boot image will prevent the automatic recovery installation. If you're not sure which recovery you have installed, you can always do a 'adb reboot recovery' from Android without risk of data loss.
WARNING 2: Make sure you use the correct scatter file for your device (i.e. don't mix up the Z300 and Z301 files). For the initial flash, there is no check for scatter file correctness. If you use the wrong one, SP Flash Tool will alter and lock your GPT to that scatter file layout, possibly bricking your device. It will not be easy to restore it. Flashing with the correct scatter file later on will not work because Flash Tool will not allow you to use a different file than the one you used initially.
What works: Basically everything... access to major partitions, decrypted userdata partition, decrypted adoptable storage, external SD card, ADB, USB-OTG, touch interface, splash screen, installing stock Asus OTA/web FW updates
What doesn't work: (no known problems yet, but please report any)
Not guaranteed to work: factory reset
DOWNLOAD
SP Flash Tool v5.1532
Z300M Scatter file for all storage sizes (right click, Save link as...) -- do not use for other models
Z300M TWRP 3.2.1-0 image -- updated March 15, 2018
Z301M(F) series Scatter file for all storage sizes (right click, Save link as...) -- do not use for Z300M or other devices
Z301M TWRP 3.2.1-0 image -- updated March 13, 2018
Z301MF TWRP 3.2.3-0 image -- updated August 29, 2018
Development and experimental files
Source code
P.S. The thanks button doesn't bite.
Heya, thanks for the new thread..
Stupid question(coming from Samsung flashing)
Ive got Zenpad S3 10 P027, is this TRWP not ideal for this?
Currently, have some su (root) issues. Recovery shows Android icon chest with ! and says "No Command"
When running su in Terminal ADB via PC, says command not recognized.
Looks like I need to reflash recovery. When in TRWP (launched via fastboot boot twrp on PC) I flashed stock recovery but had system mounted read only. Could that be the problem?
Bro, I think you need to do some more homework on root, su, dm-verity, mods, etc. and read the instructions more carefully before applying these hacks. You are making a lot of simple mistakes and ending up shooting yourself in the foot for it. I don't think there's anything wrong with the Z500 TWRP. It can handle installing the stock firmware just fine. The problem is elsewhere. The unlock tool also works fine in TWRP as well in my testing.
The No Command screen is normal. That's been answered many times... you need to hold power+vol. up (or down) to get to the menu. There is no way the stock recovery image can be broken and still boot up.
The su thing, IDK what the problem is, but I'm sure if you install Magisk Manager and make your own patched image from your currently installed firmware, and fastboot-boot with it, you will have su functionality. Just like what it says in the unlock tool instructions.
Lastly and most important, never mount system in read-write mode, as I've repeated several times and exactly as it says in the directions:
7. At the TWRP welcome screen, do not select to modify the system partition and touch Keep System Read-only instead. Doing otherwise will render your tablet unbootable.
8. Mount system in TWRP (in read-only mode)
Click to expand...
Click to collapse
The only time you can mount it in read-write mode is when you are absolutely sure you have disabled dm-verity in your boot image.
I've successfully installed TWRP on Z301M using the instructions from the first post, but then I somehow managed to lose the system. Yes, I should have backed up like the OP suggests.
I thought I should be able to reinstall the original firmware downloaded from Asus (e.g. UL-ASUS_P028_1-WW-3.3.12.0-user.zip) but both the 'adb sideload' method and the TWRP failed to install that firmware zip. My device looks bricked. The only thing I can do is to boot into TWRP (I actually need to select Factory Reset on the bootloader screen to get into TWRP). The folder 'system' is empty.
Can anyone suggest what I am doing wrong when trying to restore the Asus firmware?
When I try to sideload the zip, setting TWRP in the sideload mode, the computer begins uploading but after a few seconds gives the message "Total xfer: 0.01x" and stops, while Android errors with "set boot part fail. can not open misc-sd".
When I install the firmware zip from TWRP it also starts installing fine but shortly gives the same error "set boot part fail. can not open misc-sd".
Thanks
@ahacker, first of all, thank you for the feedback on the Z301M platform. You are literally the first person to have said anything about that version of TWRP.
To see the files on system, you first have to mount the system partition. Did you do that? If not, I suggest mounting it read-only. If there was any corruption on it, then reinstalling the firmware should have fixed it. The "misc-sd" errors are normal. Pretty sure they happen on stock recovery too. The stock firmware does not have dm-verity enabled, so letting TWRP modify system to prevent overwriting recovery should not have caused any problems.
At which point did it stop booting? Also, did you use the scatter file from first post? And can you tell me if the touch screen works fine in TWRP on your tablet?
I'm not sure what the deal is with adb sideload. I don't think I've ever actually tried it....
diplomatic, thanks for replying!
diplomatic said:
[MENTION=4776997]
To see the files on system, you first have to mount the system partition. Did you do that?
Click to expand...
Click to collapse
I do mount the system partition. It appears empty. When I reboot into system TWRP says that the OS is not installed.
I don't remember the details of how I lost the system partition. First time I entered into TWRP it asked for a password, probably to mount some partition. I pressed cancel or something. Then I might have cleaned the caches. But I am sure I haven't wiped system. I might have pressed Factory Reset somewhere, because I don't have any data yet on the new tablet.
I would indeed try to mount the system read only. This is not the first Android system I rooted (maybe fifth), and I was always able to restore the system either from sideload or recovery. But here it seems Asus is making us jump extra hoops to do that.
diplomatic said:
[MENTION=4776997]
Reinstalling the firmware should have fixed it.
Click to expand...
Click to collapse
That seems to be my main problem now. I cannot reinstall the Asus firmware. It may look like I might be installing a wrong version, but I am positive that I have Z301M tablet. This is what I bought and what the boot-loader says. I download Z301M firmware from the Asus website (e.g.). So it must be a correct firmware.
diplomatic said:
[MENTION=4776997]
The "misc-sd" errors are normal. Pretty sure they happen on stock recovery too. The stock firmware does not have dm-verity enabled, so letting TWRP modify system to prevent overwriting recovery should not have caused any problems.
Click to expand...
Click to collapse
Thank you for the information.
diplomatic said:
[MENTION=4776997]
Also, did you use the scatter file from first post? Does the touch screen work fine in TWRP on that tablet?
Click to expand...
Click to collapse
Yes. I found that to be the only scatter file that worked. I tried scatter.txt from the firmware zip, but the Flash Tool refuses tio pick it up. TWRP seems to be working fine with touches working as expected.
diplomatic said:
[MENTION=4776997]
I'm not sure what the deal is with adb sideload. I don't think I've ever actually tried it....
Click to expand...
Click to collapse
This is the unbricking method described here. It probably does the same thing as the "Install Zip" from recovery, because the errors that both methods give are the same.
---------- Post added at 01:19 AM ---------- Previous post was at 12:57 AM ----------
Now system refuses to mount
ahacker said:
I don't remember the details of how I lost the system partition. First time I entered into TWRP it asked for a password, probably to mount some partition. I pressed cancel or something. Then I might have cleaned the caches. But I am sure I haven't wiped system. I might have pressed Factory Reset somewhere, because I don't have any data yet on the new tablet.
Click to expand...
Click to collapse
Er, the password should have been for decrypting your userdata. If you didn't have one set up, there might be something wrong there.... Or possibly just unformatted.
ahacker said:
That seems to be my main problem now. I cannot reinstall the Asus firmware. It may look like I might be installing a wrong version, but I am positive that I have Z301M tablet. This is what I bought and what the boot-loader says. I download Z301M firmware from the Asus website (e.g.). So it must be a correct firmware.
Click to expand...
Click to collapse
Yeah, that has to be the right one. The installation script has to match the model name reported by the recovery. Otherwise it would simply abort.
ahacker said:
Yes. I found that to be the only scatter file that worked. I tried scatter.txt from the firmware zip, but the Flash Tool refuses tio pick it up. TWRP seems to be working fine with touches working as expected.
Click to expand...
Click to collapse
Great! Guess my kernel patch was on the dot and the partition layout has not changed from the Z300.
ahacker said:
This is the unbricking method described here. It probably does the same thing as the "Install Zip" from recovery, because the errors that both methods give are the same.
Click to expand...
Click to collapse
When you installed the zip, did you unmount system completely? BTW, when you mentioned the errors, the installation does keep going for like 5 to 10 minutes afterwards, right?
If you still can't resurrect it, please post or send me the recovery & kernel log that has your installation attempt.
diplomatic said:
When you installed the zip, did you unmount system completely? BTW, when you mentioned the errors, the installation does keep going for like 5 to 10 minutes afterwards, right?
Click to expand...
Click to collapse
I've tried both ways, with and without system mounted, a few times. The installation would fail after something like 5 seconds.
diplomatic said:
If you still can't resurrect it, please post or send me the recovery & kernel log that has your installation attempt.
Click to expand...
Click to collapse
I think I am giving up on this cheap tablet. I cannot even format it in the Flash Tool: it says "To format code area is forbidden on this phone". Asus is forbidding too much for me to ever buy it again. Attached the logs.
Thanks, diplomatic
OK, found the problem. Check your PMs, ahacker.
diplomatic said:
OK, found the problem. Check your PMs, ahacker.
Click to expand...
Click to collapse
I have replied (twice), but the reply does not appear in my Sent Items. I hope it has reached you. If not, I'll paste the reply here, if you don't mind.
i not understand... i have Asus ZenPad 10 LTE Z301MFL.. a root method has been released ???
@diplomatic
Would this be compatible with Z0310M ? can't find anything for this damn model...
Hi, NeBouse,
Are you sure you have the correct information? It looks like just a misspelling of Z301M, aka P028....
I have z301m.
One thing that was a surprise for me is that the TWRP recovery flashed with the method described in the original post does not stick. You have to flash it each time you use it. If you are like me this information is important, because the original recovery plainly wipes your data without asking or warning.
After you have flashed TWRP on the device, to go to the recovery mode you have to chose "Factory Reset" in the bootloader. Then it will complain about wrong OS, which is the sign that flashing TWRP worked; choose 'yes'. The first thing you should do in TWRP is a ful nandroid backup. (Not listening the OP's advice about backing up when Installing TWRP with a wrong scatter file almost cost me the device. Thankfully diplomatic managed to remotely fix my problem, probably spending a lot of his personal time. The scatter file in the original post is a correct one now.)
Creating a nandroid backup in TWRP takes unusually long time, I even once decided that it hanged. Taking long time, like 10-30 minutes, for a full backup is normal.
Asus Z300M , Magisk 16.3 (beta) and FW 5.3.19 WW now works!
z301m, WW-3.3.12.0 firmware
For rooting I've installed in TWRP Magisk v15.3 (diplomatic warned against 16.x, someone else against 15.4) - link.
Installed in TWRP xPosed framework 88.2 - link, and xPosed Installer apk from within Android - link.
So far, so good.
What I've found is that TWRP seems to have problems with external sd cards (lots of fs corruption). I found it safer to unmount by hand by unticking the sd card checkbox in "Mount". Not very conclusive about this though.
Thanks, ahacker. Good feedback. Although to be fair, I didn't say to avoid Magisk 16.x. I said 16.0. I'm pretty sure whatever bug it had is already fixed in the latest version.
Now that you've installed root, TWRP will stick around on the emmc. The stock recovery only gets installed if you have the original unpatched boot image on it. I mean, this is not unique to these devices. That's been standard Android functionality since some 4.x or 5.x version. And this is essentially what's in the warning on the OP.
The backup I'm talking about in the installation method is done with the SP Flash Tool readback function. That will pull the partition tables and your device's "metadata" that's unique to your unit. I don't think nandroid covers that...
Oh, and what is this SD corruption you're talking about? What file system is it formatted in? Have you checked your card for errors in Windows?
Asus releases so many difference Z301M model, so I am curious if this also works on Z301MF model?
Notice Z300MF has the MTK8163BA (or MTK8163A?) CPU model while Z301M uses : 8163B
Anyone tested that already? Thanks.
my zenpad 10 has frp lock. it this a solution to remove the frp lock?
Pls help how i flash original software via fastboot ?????
I just bought a Nuu R1 Rugged Phone. It has Oreo 8.1.0 on it.
It is an "unlocked" phone. But I don't know if unlocked refers to the phone carrier or to the boot loader. (I'm thinking phone carrier.)
The last I rooted my tablets was Android 5, which required using a custom script that a dev here wrote that temporarily ran CW via fast boot.
I would like to root my R1. I hear now that Magisk is the way to go. (Instead of SU.)
Most every Guide says that I have to have TWRP installed before installing Magisk. But there's no TWRP for the R1. And I am incapable of compiling my own.
I learned, from Nuu Tech Support, that I can get into the phone's Recovery mode with some hidden button pushes. Here's a screen shot:
My first question is, could I simply install Magisk by selecting "Update from SD card"?
If it's not that easy, then, second: I can also get to a fastboot screen. (Not shown here.) Could I install Magisk from ADB on my computer?
I suppose a third question: Is there a version of TWRP that's compatible with this phone? And if so, how do I find it? It would be nice to have a Nandroid backup.
I am willing to show various screens that come up from various button pushes if that would help a dev here.
More data for TWRP'ing
So, I see that one needs an image of the OEM ROM to compile TWRP. I found two sites on the web that claim to have the ROM. (Before the R1 was officially released.) Sounds sketchy. Will try to get an image from Tech Support.
In the meantime, I found that the bootloader can be unlocked (or allowed to be unlocked) via a setting under Developer Options.
I contacted Nuu Mobile Support and they were kind to send me the MediaTek USB drivers for the R1.
It was a two step process to get the driver installed for ADB. But now I have access to the R1 via ADB.
I read here on the forums that I can boot TWRP via fastboot, and not risk ruining/corrupting the R1's Recovery Partition.
Anyone know of a TWRP model version that's close enough to work on the R1? (I presume a TWRP for another MediaTek device might work?)
I would hate to try KingRoot to get root.
I found a website called unofficialtwrp.com. It has a TWRP for the MediaTek 6739, running Oreo 8.1, with 16/2 GB. That's exactly what the Nuu Mobile R1 has.
So, hopeful that this would allow me to root my R1, I tried it. (Short version: Didn't work.)
I already had ADB installed and could talk to my R1 via ADB.
But once the R1 had booted into fastboot mode via ADB, I got a message from fastbood devices that it was "waiting."
I learned that that message means that I didn't have drivers for fastboot.
I ended up installing a fresh version of Win8.1 and using the Windows' updater to find the needed drivers. I had to have the R1 plugged in to the USB in fastboot mode for this to work. After that, I could talk to the device via the fastboot command.
So I unlocked the boot loader (which wiped my data - not every Guide warns you about that) and I did "fastboot boot recovery.img."
I got the message that the recovery file had transferred. After abotu 15 seconds, the phone rebooted. But no TWRP.
Rats.
I didn't want to try the fastboot flash command in case this unoffiical twrp from an unofficial site bricked my phone. If I understand things correctly, booting in fastboot to the recovery.img should give me a temporary instance of TWRP.
Presumably, after copying Magisk into memory, I would be able to get root that way.
PMikeP said:
I found a website called unofficialtwrp.com. It has a TWRP
Click to expand...
Click to collapse
Whoa you have been busy you must've heard XDA helps those who help themselves.. :highfive:
I just dropped by to say, 1st rule of modding is taking a pristine stock backup..
For MTK devices, there is a tool called SP Flash Tools, a quick search will help you take a full backup using this tool.
Afterward, you can even try using SP Flash Tools to flash a Magisk patched boot image to your device for ROOT!
Hope this helps!
Thanks. I did see SP Flash Tools mentioned and I did take a look at it. While I've rooted before, I'm trying to get my head around a Scatter File.
Everything I've read so far - well, almost everything - says that I need TWRP to get Magisk installed. But if you think it can be done via SP Flash Tools, I'll start playing with it.
Root nuu r1
Did u ever manage to figure out how to do this & get TWRP to install? :fingers-crossed:
No, I haven't had time to play with rooting lately. I still would like to root it tho.
Anyone know how to root the nuu phones?
someone has the boot.img i need the image
I will port TWRP for you in case you have stock recovery.img
jjgvv said:
I will port TWRP for you in case you have stock recovery.img
Click to expand...
Click to collapse
plis
do you have stock rom?
As the title states. Sorry if this has been covered already. Currently on Android 12 SQ3A.220705.004 with Magisk 25.2.
Others correct me if I am wrong, and don't take my advice before doing it, but I am under the impression it is just like any other upgrade. With the exception of making sure the new A13 boot gets flashed to both slots.
Steps I think are still valid:
1. Download the OTA to PC
2. Extract boot, copy to phone
3. Patch A13 boot with manager
4. Copy patched boot to PC
5. Reboot to recovery and sideload OTA.
6. Reboot to fastboot and flash patched boot to BOTH slots
7. Reboot to fastboot, NOT system.
8. Reboot system
What's wrong with reading the how to guides in the Pixel 6 threads?
It would definitely help with this BS clutter...
vandyman said:
What's wrong with reading the how to guides in the Pixel 6 threads?
It would definitely help with this BS clutter...
Click to expand...
Click to collapse
It's a lot to familiarise myself with, I thought I'd just ask to gauge whether or not it's worth trying now or waiting.
Still, there are 2 guides which are more detailed and using the OTA is frankly a little bit more complicated than use for example the factory image.
The OTA contains a boot image, but it is inside the "payload.bin". So you need to extract the "payload.bin" first to get the boot image for patching. So, get the factory image, you find all goodies already in the zip file.
Easiest and fastest way, update on your mobile to Magisk 25.2 before updating to A13 and then use the Pixelflasher, and flash the image to both slots.
Cheers
Tom
Hi, I've just bought a Cubot P50, it's a Chinese brand and seems more than decent for the price, I've rooted it with Magisk and I want to install TWRP on it but can't find anything for that brand. Has anyone came across a TWRP that might work on it?
Marko Lyno said:
Hi, I've just bought a Cubot P50, it's a Chinese brand and seems more than decent for the price, I've rooted it with Magisk and I want to install TWRP on it but can't find anything for that brand. Has anyone came across a TWRP that might work on it?
Click to expand...
Click to collapse
I have the same phone how did you root it ? If there a guide that is safe to use ? Thank you
Unlock the bootloader first, this step will factory reset your phone https://romprovider.com/unlock-bootloader-android/
On your PC:
1. Install Fastboot driver
2. Install MediaTek_Preloader_USB_VCOM_Drivers_Setup_Signed
3. Extract platform-tools
4. On your phone, Enable Developer Options, USB debugging and OEM Unlocking
5. Unlock bootloader (this step will factory reset your phone): Phone in fastboot mode, open command prompt on PC > fastboot devices > fastboot flashing unlock. Note this will cause the phone to show the "Orange State" warning on boot up. You can ignore this or remove it later.
(If device is unauthorised in ADB or Fastboot, go to Developer Options on phone, revoke USB debugging authorisation, disable then enable USB debugging. You should now get an authorisation confirmation dialogue when you try to connect with ADB/Fastboot. If not, type "adb kill-server", then "adb devices" or "adb start-server" in the command prompt).
6. Place boot.img on phone with USB file transfer (either from stock ROM, or read from phone using SP_Flash_Tool_v5.1924_Win) and patch it with Magisk v5.2. NO need to patch vbmeta.img
7. Transfer patched boot.img back to PC
8. Flash the patched boot.img to phone either with SP Flash Tool or Fastboot command in ADB (fastboot flash boot boot.img). Take care here, make sure it's the right image going to the right location and that ALL other files are de-selected, especially the preloader file, always de-select this when flashing any firmware unless you know what you're doing!
Phone is now rooted.
How to remove orange state warning on this device:
How to remove Orange, Yellow & Red state warnings on MTK
This guide will explain how to hide or remove Yellow, Red and Orange state warnings on a Mediatek Android device. Its ideal for those who feel irritated by constantly seeing these warnings on reboot.
www.hovatek.com
Edit: If you need a stock ROM for the phone it's here https://www.cubot.net/Support/id/78/cid/19.html#hh
Good evening, I would like to know if in the future it is possible to install a twrp with a custom rom?
Thank you have a nice day.
Good evening, I would like to know if in the future it is possible to install a twrp with a custom rom on the Cubot p50?
Thank you have a nice day.
Mark8:9 said:
Good evening, I would like to know if in the future it is possible to install a twrp with a custom rom on the Cubot p50?
Thank you have a nice day.
Click to expand...
Click to collapse
It is possible that in the future, developers may create custom ROMs and TWRP recoveries for the device, especially if it becomes popular among the Android community.
If a custom ROM and TWRP recovery becomes available for your device in the future, you will be able to flash it by following the instructions provided by the developer. Keep in mind that installing custom ROMs and recoveries comes with some risks, and it is important to backup your data and follow the instructions carefully to avoid damaging your device.
Good evening, can you tell me the correct procedure for how to Root the Cubot p50 smartphone? Thank you.
Mark8:9 said:
Good evening, can you tell me the correct procedure for how to Root the Cubot p50 smartphone? Thank you.
Click to expand...
Click to collapse
Well if you really want to know that, surely you would have read the entire thread? It's not that long. I gave complete instructions 5 posts up
Marko Lyno said:
Well if you really want to know that, surely you would have read the entire thread? It's not that long. I gave complete instructions 5 posts up
Click to expand...
Click to collapse
Good evening, be patient ... but where do I find Magisk 5.2 to download and how do I install it? Thanks good evening.
Download Magisk Manager Latest Version 26.1 For Android 2023
Magisk Manager is an app which helps users to root their phone. With the help of Magisk you can run banking apps and also pass SafetyNet tests.
magiskmanager.com
Just get the latest version and follow the instructions I posted.
Thanks for your work on the Cubot phone .Im a fan of them also. I found that twrp recovery 3.40 works on the Note 20/20Pro you just have to flash vbmeta BEFORE and AFTER you flash twrp to the device. Im also seeing separate websites claiming twrp 3.40 is also used with the Cubot P40 model. I dont see why it wouldnt work with the P50. Its worth a shot. Also theres alot more "familiars" with Mediatek phones like these in Hovatek forum. Since you already have information on how to root maybe consider starting your own P50 thread over there.
My references: https://www.hovatek.com/forum/thread-44810-post-233457.html#pid233457
elimoviebuff said:
Thanks for your work on the Cubot phone .Im a fan of them also. I found that twrp recovery 3.40 works on the Note 20/20Pro you just have to flash vbmeta BEFORE and AFTER you flash twrp to the device. Im also seeing separate websites claiming twrp 3.40 is also used with the Cubot P40 model. I dont see why it wouldnt work with the P50. Its worth a shot. Also theres alot more "familiars" with Mediatek phones like these in Hovatek forum. Since you already have information on how to root maybe consider starting your own P50 thread over there.
My references: https://www.hovatek.com/forum/thread-44810-post-233457.html#pid233457
Click to expand...
Click to collapse
Thanks for that. Is there a specific vbmeta to patch it with?
Good evening, can you give me the link to download a compatible cust recovery for the cubot p50? Thank you
The link is on the page just posted above. Here's the direct link to the file:
Hovatek
Download files
www.hovatek.com
Let us know if it works please, and what steps you took.
Good evening, how will I flash the lk file? Thanks.
Hi, you will have, or should have, downloaded a zip file containing a recovery.img. The recovery.img is the file you need to flash. Then follow the instructions here:
How to Install TWRP Recovery on Any Android 2022 [100% Working]
In this article, I will be showing you how you can install TWRP recovery on any Android smartphone. By following this guide you will be able to install
magiskapp.com
The TWRP Recovery file it refers to is the one you (hopefully) downloaded from this link:
Hovatek
Download files
www.hovatek.com
BUT, you also need to flash a vbmeta file BEFORE and AFTER the recovery.img, and I'm still unsure which vbmeta file it is, as elimoviebuff hasn't replied to my question regarding that.
Marko Lyno said:
Hi, you will have, or should have, downloaded a zip file containing a recovery.img. The recovery.img is the file you need to flash. Then follow the instructions here:
How to Install TWRP Recovery on Any Android 2022 [100% Working]
In this article, I will be showing you how you can install TWRP recovery on any Android smartphone. By following this guide you will be able to install
magiskapp.com
The TWRP Recovery file it refers to is the one you (hopefully) downloaded from this link:
Hovatek
Download files
www.hovatek.com
BUT, you also need to flash a vbmeta file BEFORE and AFTER the recovery.img, and I'm still unsure which vbmeta file it is, as elimoviebuff hasn't replied to my question regarding that.
Click to expand...
Click to collapse
I get it, but I have to flash the .bin to remove the yellow/red state on boot. I don't know how to install the lk.bin file. If you can help me. Thank you.
Ah I see, you're rooting the phone first. Ok I've just checked my own notes on this, so, if you have edited the lk.img file as described in that Hovatek thread, then do as follows:
When flashing with SP Flash Tool, make sure the correct lk.img file is chosen as SP Flash Tool chooses lk-verified.img by default (click along to the right of the file list under "Location" and choose your edited lk.img file here).
OR, flash with ADB (fastboot flash lk lk.img).
Then install Magisk on your phone if you haven't already.
boot.img is for rooting the phone, lk.img is only to remove the orange state message and the 5 second delay when the phone boots, it does not actually remove it's orange state and is not needed for the phone to be rooted.
To un-root, you should just flash the original boot.img and lk-verified.img from the stock firmware ROM file.
Marko Lyno said:
Ah I see, you're rooting the phone first. Ok I've just checked my own notes on this, so, if you have edited the lk.img file as described in that Hovatek thread, then do as follows:
When flashing with SP Flash Tool, make sure the correct lk.img file is chosen as SP Flash Tool chooses lk-verified.img by default (click along to the right of the file list under "Location" and choose your edited lk.img file here).
OR, flash with ADB (fastboot flash lk lk.img).
Then install Magisk on your phone if you haven't already.
boot.img is for rooting the phone, lk.img is only to remove the orange state message and the 5 second delay when the phone boots, it does not actually remove it's orange state and is not needed for the phone to be rooted.
To un-root, you should just flash the original boot.img and lk-verified.img from the stock firmware ROM file.
Click to expand...
Click to collapse
Good morning. Thank you for the information given.
I wanted to ask: is it necessary or useful to install an antivirus on your smartphone now that it's been rooted? Thank you.
I haven't but that's just down to personal choice really. It's certainly useful if you like to try stuff from unknown sources, although personally I've rarely encountered viruses on Android. I'm not saying they don't exist though.
Have you successfully rooted your phone then? What about TWRP, have you tried that yet?