Related
Huawei Y550 - looping "Fastboot & Rescue Mode - Phone Locked" - Data Recovery needed!
Hi @dimspace, @HB72K, @patrik.KT @hecaex @ EVERYONE!!!
Hi guys, I'm asking (BEGGING) on your VAST knowledge of this device, on behalf of my brother...
He has the Huawei Y550 L01 (everything STOCK, firmware/recovery) and it's just died in a very common way as seen all over the internet. We've tried many different tricks to try reboot it, but alas all do not work. IT IS VITAL WE DO NOT LOOSE ANY DATA, as it's required for a legal case.. His phone just booted into Fastboot & Rescue Mode - Phone Locked
We urgently need to get the data off there, ie: Text Messages, Call Logs and Pictures for a legal case coming up soon.
What I would like to know, is it possible to recovery this data via either Fastboot / ADB or TWRP whilst it's in this state??
Does the phones Bootloader need to be unlocked to begin with, if so... bit late for that now as can't boot the phone. As it appears to be in Fastboot mode now, can we run Fastboot Flash Recovery TWRP.img to install TWRP recovery, and will that have root access within itself? (as I know where the messages are stored) or will this trip the phone further...
Is there any ADB commands we can use to PULL the messages out, whilst it's in this Fastboot state, but everything is STOCK firmware.
Open to all methods to recover data, it's important the data is not lost... What happens to the phone after data is (hopefully) recovered is not of importance, just the data is....
I pray you knowledgeable people can and will help us with this...
** Any idea's what caused the phone to go into this mode also?? As my brother doesn't tamper with things (unlike me) and keeps everything stock. He said it happened about a month ago, but pulling the battery and replugging it back in fixed it... But this trick isn't working now.. **
Many thanks, Lister
Hello there. I'll just give a bit of information about your case. As far as I know, you need root permission to access /data/data/"packagenameoftheapp" (where app data is stored; app data on /sdcard/Android/data -where app data is also stored - does not need root access though) and this could be "pulled" via adb which apparently you can not access since the device is in fastboot. Also, to flash or boot a custom recovery, you'll need the bootloader to be unlocked: (a) in device > settings > allow oem unlocking, then (b) in terminal: fastboot oem unlock "unlock key". Note: unlocking the bootloader (fastboot oem unlock) restores the device to factory settings which means your data is cleared too.
If you can try to boot the device normally so that you can use adb, some data could be retrieved (but only on the /sdcard), then you can root (install supersu) the device via adb (if there are possible workaround - external app maybe (kingroot for windows, etc)).
edit: Can you boot into recovery (not fastboot)? i think adb is accessible from recovery (use the volume + button keys)
IMPORTANT: It appearance that Huawei is no longer going to provide bootloader unlocking services for their devices. Because of this, this guide is of no use unless you can find a way to get a code or you just held onto the code.
Hello, this is a guide for unlocking the bootloader and rooting the Huawei Ascend XT. I am writing this because the current guide is not very well written and does not contain bootloader unlock instructions. This will be split into two parts: Part 1, unlocking the bootloader, and Part 2, rooting the phone.
PLEASE NOTE THAT FOLLOWING THESE INSTRUCTIONS WILL WIPE YOUR DEVICE. I AM NOT RESPONSIBLE FOR AND DAMAGE DONE TO YOUR PHONE!
THINGS YOU WILL NEED:
1. A Huawei Ascend XT with at least 60% of battery left
2. A computer with adb drivers, fastboot drivers, and the Huawei USB drivers
3. A Micro-SD card for your backups (THIS IS VERY IMPORTANT! PLEASE MAKE BACKUPS!)
4. TWRP for this phone. This can be found here: https://forum.xda-developers.com/android/general/huawei-ascend-xt-h1611-t3507933 (credits to enigma2446)
5. The ZIP containing SuperSU. This can be found here: https://forum.xda-developers.com/android/general/huawei-ascend-xt-h1611-t3507933
6. The SDK Platform Tools. These can be found on the android studio website.
PART 1: UNLOCKING THE BOOTLOADER1. Geting the Bootloader Unlock Code: You need to get your bootloader unlock code. You can get this by going to https://emui.huawei.com/en/plugin.php?id=unlock
(EDIT: It appears that this website is down. I have read that if you PM Huawei on Twitter or call them and provide all the details of your phone, they will give you a code. I have not tested this method, bit people have said it worked with the mate 10.) and signing into your Huawei ID. If you dont have one, create one. Then, follow the instructions given to you by Huawei to get the code.
2. Enabling the Enable OEM Unlock Option: To enable this option, you must enable developer options. To do this, go to Settings>About Phone and tap the Build number until it says "You are now a Developer". back out of About Phone, and go to Developer options. turn on "Enable OEM unlock" and press Enable.
3. Enable USB Debugging: While you are still in Developer options, enable the option 'USB debugging" and press OK.
4. Booting Into the Bootloader: once you have completed the first three steps, you can now boot into the bootloader. Connect your phone to your computer, and open the Platform Tools folder you should have downloaded and extracted. Shift-Right click, and press "Open Command Window Here" or "Open Powershell Window Here", depending on your version of windows. Once it is open, make sure your device is detected by typing "adb devices". If it displays your device, you are good to continue. If not, something is not set up right on your computer or phone. Once you verified that your phone is detected, type "adb reboot bootloader".
5. Unlocking the Bootloader: Once your phone has booted into the bootloader, you can now unlock the bootloader. YOUR PHONE WILL BE WIPED ONCE YOU TYPED THIS COMMAND. You can unlock it by typing "fastboot oem unlock <your bootloader unlock code>". Once it has finished, you can reboot your phone, and just run through the setup fast, because you will still have to wipe it again.
PART 2: ROOTING YOUR PHONE1. Move the TWRP image you downloaded (called
Xtrecovery) to your Platform Tools folder and rename it to "TWRP.img"
2. Insert Your Micro-SD Card
3. Move the SuperSU Zip you downloaded to the SD card
4. Re-Enable USB Debugging: Enable Developer options by going to Settings>About Phone and taping the Build number until it says "You are now a Developer". Back out of About Phone, and go to Developer options, and enable USB debugging, and press OK.
5. Boot Into the Bootloader: Type "adb reboot bootloader" into your open CMD window or Powershell window.
6. Verify That your Phone says that the Bootloader is unlocked
7. Type "fastboot boot TWRP.img"
8. TWRP should boot. Tap "Keep Read Only"
9. You should now be in TWRP. Go to Backup>Select Storage and choose your Micro-SD card and tap OK. Uncheck everything and check "Recovery". Then, Swipe the slider to back up your stock recovery partition.
10. Once it has finished backing up, reboot your phone to the bootloader.
11. Once it is in the bootloader, type "fastboot flash recovery TWRP.img" to flash TWRP as your recovery. (I believe this is the point where your warrenty will be invalidated by Huawei, so be careful.)
12. When it finishes flashing TWRP, reboot your phone to TWRP by holding down the power button and volume up
13. It should boot to TWRP. Tap "Keep Read Only", then go to (YOU ARE ABOUT TO WIPE IT AGAIN)Wipe>Format Data and type yes, and hit the enter button.
14. Once it finishes, go to Backup>Select Storage, select your SD card and hit OK, then check every box to backup all six partitions, and swipe to back them up. (At the end, it may seem to get stuck at 98-99%, DO NOT STOP IT! It is generating an MD5 checksum)
15. When it finishes backing everything up, go back to the home screen of TWRP, then go to Install, navigate to where you stored the SuperSU ZIP, select it, then swipe to flash it.
16. When it finishes flashing the SuperSU ZIP, tap "Clear Cache/Dalvik" and swipe to clear them.
17. Reboot your phone. IT WILL REBOOT MULTIBLE TIMES AND APPEAR TO BE STUCK SOMETIMES, BUT DONT TOUCH IT! This is normal and it will eventually boot like normal.
That's it!
Your phone should now be rooted and have SuperSU installed. Please note that this is a Systemless root, and will be removed if you factory reset your phone.Thanks to divineBliss for creating the original instructions.
What do we do after we get root to install custom ROMS? please advise
nedfred0 said:
What do we do after we get root to install custom ROMS? please advise
Click to expand...
Click to collapse
To install a custom ROM, you need the ROM you want to install, gapps depending on the ROM, and the proper firmware. The firmware you are on can be found under about phone and is the last 4 digets of the build number (in the format of B1xx). Once you are on the proper firmware, have your ROM and other things it may require, (every ROM is different), and a backup (just in case), you can flash the ROM from TWRP. Follow the instructions provided by the creator of the ROM to properly flash it.
Where do you get the USB driver at because I am not seeing it at http://consumer.huawei.com/us/support/phones/ascend-xt/
BTJustice said:
Where do you get the USB driver at because I am not seeing it at
Click to expand...
Click to collapse
The drivers come with HiSuite. Download it and you should be good to go.
randomness725 said:
The drivers come with HiSuite. Download it and you should be good to go.
Click to expand...
Click to collapse
Thanks. I tried that but couldn't get it to go so I downloaded these instead which did the job:
https://www.androidfilehost.com/?fid=817550096634745788
does this work on the new h1711 huawei assend xt2
xaneth201 said:
does this work on the new h1711 huawei assend xt2
Click to expand...
Click to collapse
It will not. The TWRP recovery image is device specific and might brick your device if you flash it to your phone.
bricked 1711
randomness725 said:
It will not. The TWRP recovery image is device specific and might brick your device if you flash it to your phone.
Click to expand...
Click to collapse
Well I did not see that, so yeah, I have bricked it. IT comes up and says it is unlocked, it used to sit there then boot into the system.
So I downloaded the TWRP, tried to reboot to recovery and nothing.
Now, it just gets to the yellow warning screen, then goes black. Just bought this today on a black friday sale for 49.00
But did it for a reason. Now I would like to be able to recover it....
I was able to run adb and fastboot, so know that the drivers work, but it looks like it won't even get there now.
And it won't even go to the recovery, so I guess this phone is a real brick.
Can't seem to get the back cover off to remove the battery either.
You need a copy of the stock H1711 recovery image to use
"fastboot flash recovery H1711-stock-recovery.img" to restore the stock recovery. Until someone creates a working H1711 TWRP, I don't know where you'll find a stock H1711 recovery image file.
scrungydoolittle said:
Well I did not see that, so yeah, I have bricked it. IT comes up and says it is unlocked, it used to sit there then boot into the system.
So I downloaded the TWRP, tried to reboot to recovery and nothing.
Now, it just gets to the yellow warning screen, then goes black. Just bought this today on a black friday sale for 49.00
But did it for a reason. Now I would like to be able to recover it....
I was able to run adb and fastboot, so know that the drivers work, but it looks like it won't even get there now.
And it won't even go to the recovery, so I guess this phone is a real brick.
Can't seem to get the back cover off to remove the battery either.
Click to expand...
Click to collapse
download hisuite, enable oem unlocking and usb debbuginig, you gotta also get tha password or the unlocking, denn u run cmd and type:
adb devices
i hope i helped
there is easy way to get unlock bootloader pass for all huawei
just by IMEI search on google "hardreset24 unlock bootloader" there is full info how to do it
BTJustice said:
Where do you get the USB driver at because I am not seeing it at http://consumer.huawei.com/us/support/phones/ascend-xt/
Click to expand...
Click to collapse
Here is the site for USB drivers for all Huawei models:
http://huaweiadvices.com/download-huawei-usb-drivers/
Good luck....
Does the phone even have a fastboot mode?
RomLord14495 said:
Does the phone even have a fastboot mode?
Click to expand...
Click to collapse
Sure it does
Notes on booting up the phone (from power off)
Bootloader (fastboot) = power + volume down + USB hooked to pc
eRecovery = power + volume up + USB hooked to PC
TWRP = power + volume up
Click to expand...
Click to collapse
Optionally you put phone into bootloader/fastboot or recovery modes by typing from an adb prompt "reboot bootloader" or "reboot recovery"
Hi there. The website link for submitting your imei to get the unlock code doesn't work. Does anyone know how to get this code now?
dominoes20 said:
Hi there. The website link for submitting your imei to get the unlock code doesn't work. Does anyone know how to get this code now?
Click to expand...
Click to collapse
You'll have to use DC Unlocker and pay to unlock until the page returns
Since unlocking the bootloader is no longer supported, I have a suggestion but am afraid to try myself.
So, download stock version of rom (aka fastboot rom). Extract, replace recovery.img with twrp (renamed to recovery.img). Restart phone in EDL mode, flash. In theory, edl is working fastboot mode so it shouldn't matter if bootloader is unlocked, correct?
ezopantyd said:
there is easy way to get unlock bootloader pass for all huawei
just by IMEI search on google "hardreset24 unlock bootloader" there is full info how to do it
Click to expand...
Click to collapse
Imma try this out, I’m stuck in a weird situation where my sd card slot broke. When I sent it in for service, they said it was rooted and refused to fix it. I specifically did not root it so that I could send it in for warranty service. So it’s mission to try and root, unlock boot loader etc so that I can have more storage space
---------- Post added at 11:50 AM ---------- Previous post was at 11:36 AM ----------
ezopantyd said:
there is easy way to get unlock bootloader pass for all huawei
just by IMEI search on google "hardreset24 unlock bootloader" there is full info how to do it
Click to expand...
Click to collapse
Can you be a little more specific? I didn’t get that info on google
Hey there,
i was wondering if anyone got an idea how to get root access / TWRP working on a Doogee T6 Pro ?
I don't really find anything online that seems to be working and of course most one-click root tools dont work for China phones.
Anyone got any idea ? The official forums look empty as well.
It looks good
Applesoap said:
Hey there,
i was wondering if anyone got an idea how to get root access / TWRP working on a Doogee T6 Pro ?
I don't really find anything online that seems to be working and of course most one-click root tools dont work for China phones.
Anyone got any idea ? The official forums look empty as well.
Click to expand...
Click to collapse
Some useful tips for rooting MAZE Alpha, perhaps will help you : MAZE Alpha root
Use the method I to patch your boot.img with Magisk-v14 and flash the result image, it must works
Here is the HowTo, have done it 3 times yet:
First, get the correct TWRP Version for Doogee T6Pro ( i dont remember where i got it, i can upload it somewhere if someone have a good location) and the SuperSu Zip.
Then, activate the Developer Options in the Device Settings and Activate the OEM Unlock and USB Debugging in there.
The next Step is to Boot the Device in Fastboot mode. you can either do it by USB with the Terminal Command: "adb reboot bootloader" or you can turn the device of and then reboot it by pressing the Volume Up Button and the Power Button simultanously (quite difficult, didnt Work every Time). You will get to a menue with 3 options: Boot to Recovery, Fastboot and Normal. Switch through these Options with the Volume Up Button and Select it with the Volume Down. Go To the Fastboot Option and Select it.
In Fastboot Mode, plug in the device to an computer and type the terminal command "fastboot oem unlock" (in windows, you have to install the fastboot tools. i dont remember that i had to install them in ubuntu... im not sure). this will wipe the whole data of the device. its important to reboot the device afterwards normaly. otherwise it could happen that you get stuck in an bootloop later ( happend twice to me ) this normal system boot will last much longer then normal, so get a coffee or tea
the next step is do get to fastboot mode again and then send from your computer the command: "fastboot flash recovery twrp-recovery-filename.img". this will flash the recovery.img on the recovery partition.
than go to the bootloadermenue and this time you dont choose fastboot but the recovery option. this will start TWRP
while TWRP is running, you can copy the SuperSU zip to the device with Nautilus or in windows systems with windows explorer. then select "Install" in TWRP and select the SuperSU.zip.
After the installation, reboot to normal system and you are ready with rooting!
if something goes wrong, it can happen that booting to normal system will get you stuck in an bootloop. the last time i could repair the system by booting into recovery (TWRP) and select the Wipe menue and there the Format option. the other time i downloaded the original system from Doogee and flashed all partitions. im not sure if that was necessary.... but who knows :fingers-crossed:
1-step
in order to root these qilive devices you will need...
magisk manager apk v5.6.4
stock boot.img file
working ADB to unlock oem and flash
2-step
lets get to it
place the magisk.apk and the stock boot.img
in the internal memory of your phone (downloads)
if you like to keep stuff organized :good:
3-step
follow the vídeo tutorial and use magisk manager
to patch your stock boot.img it will output a new
boot.img that includes magisk Root (patched_boot.img)
https://www.youtube.com/watch?v=BF4_hnKgjFA
ps: major ty to hovatek team for this great tutorial
step-4 use Google drive or usb OTG to get the patched_
boot.img to your PC and place it in the ADB folder
once you have oem(bootloader) unlocked just
rename the patched_boot.img to boot.img
step-5
unlock oem, these qilive devices wont unlock
the bootloader even if you enable it in DEV options
enable USB debug in dev options
you will need to use ADB commands
command- adb devices
serial appears
command- adb reboot bootloader
phone reboots to fastboot mode
command- fastboot devices
serial appears
command- fastboot oem unlock
(MAJOR WARNING the fastboot
oem unlock will wipe/reset/factoryreset/delete your data)
after you give the command small letters will appear
on the phone screen(yes or no) hard to read dont be hasty plz
use VOLUME+ to select and VOLUME - to confirm
note: when my phone ended the unlock it whent back to
that black screen where you choose fastboot-recovery-restart
and was stuck there, side keys did nothing if this happens
just long press the power key for 10 sec it will shutdown
then press power again to turn on
first boot after unlock will take longer then normal dont freakout
after you unlock small letters will appear during boot up saying the device
is not safe unlocked ,you can later use ( fastboot oem lock )
step-6
flash the patched boot.img with ADB
command- adb devices
serial appears
command- adb reboot bootloader
phone reboots to fastboot mode
command- fastboot devices
serial appears
command- fastboot flash boot boot.img
finished/ok
command- fastboot reboot
and voila you should now have magisk
installed in the app drawer, open it!!
step-7 run the install one final time from the
magisk manager and install magisk V16 using
recomended option it will verify/patch the boot image
Do NOT select the AVB 2.0 BOX it will bootloop the phone
and your done, enjoy your qilive rooted phone.
from this point on you can use the fastboot
command- fastboot oem lock
to remove the letters in boot up about the
device not safe unlocked
WARNING oem lock
will WIPE/FACTORY RESET again (god damn it!!)
ps: i had to install twice in a row,major pain in the ....
Repeat step 7 after Wipe/Reset
here is the stock boot for 2 qilive models
you can get the stock firmware for any qilive
at this site www.doc-doapi.com/EM/qilive/smartph...te_3m-fdd-cs_mul_20170818-110645_songlixin_PC
and get the recovery or boot from the unpacked firmware file
ps:my phone is the Q8SIN4GP AND ITS WORKING FINE
A VERY SPECIAL TY to topjohnwu (magisk creator), this man is nothing
short of a God damn genius!! , and if you can donate to him.
hope this helps other qilive users to root:highfive:
quick note on the qilive models, they have two model names
the cliente name in my case Q8SIN4GP
and the factory name in my model its 882912
in order to download the right firmware for your model
you need the factory model witch is what appears in the qilive
site above, it will be in the back of the phone or the original
box on a sticker just bellow the bar code, full model exempl
:Q8SIN4GP/882912 my firmware serves several models,
these Q8 models all start with 88xxxx WARNING
dont try this using the wrong firmware/boot file or you will DAMAGE your phone
Help with BOOTLOOP problems, if you find your self stuck in a bootloop
the phone wont go past the qilive logo and just stays there, dont freak out
you will loose your data but there is a way out
just keep pressing power + Volume up until a black screen with 3 options appears
when it does let go, use Volume + to select option and Volume - to confirm
select Fastboot or alternative select recovery and then select reboot to bootloader
both option will place your phone in Fastboot mode, once in fastboot mode
connect your phone to PC and use ADB commands to fix/bootloop
command- fastboot devices
serial appears
command- fastboot oem unlock (skip this if you use phone unlocked)
a confirm action option appears on the phones screen
use Volume up to say YES / or Volume Down to say NO
Warning oem unlock will WIPE/Factory reset your phone
once it finishes the phone will be stuck on the
Recovery/fastboot/restart screen just long press the power key
until the phone shuts down
start the phone again using Power + Volume up when the black
screen with the 3 options come up, let go and use Volume up to
select Fastboot mode and confirm using Volume Down
Once in fastboot connect your phone to PC and use ADB commands
command- fastboot devices
serial apears
Here you will flash the magisk patched_boot.img
the same image you used to root your phone
command- fastboot flash boot boot.img
it will say finished-ok (or similar)
command- fastboot reboot
the boot up time will be longer than normal
but the phone should now complete the boot
and present the inicial setup screen, select language
enter your mail, the usual bla bla...
any way at this point just repeat step 7
to get root running again
sp flash tools v5.1716.
phonedriller said:
1-step
in order to root these qilive devices you will need...
magisk manager apk v5.6.4
stock boot.img file
working ADB to unlock oem and flash
2-step....
Click to expand...
Click to collapse
Hi phonedriller,
phew, I did it! (Q8S55IN4G2), thanks.
Next step: Have you found a compatible custom recovery? (especially for nandroid backups and for xposed installation)
Would be very thankful for your help!
thanks
xdatheresianum
xdacktheresianum said:
Hi phonedriller,
phew, I did it! (Q8S55IN4G2), thanks.
Next step: Have you found a compatible custom recovery? (especially for nandroid backups and for xposed installation)
Would be very thankful for your help!
thanks
xdatheresianum
Click to expand...
Click to collapse
Awsome work congrats, as for the recovery so far no luck so try not to go 2 crazy until a working recovery is up and working , install stericsons busy box this is always the first root app i install
If possible buy sterics busybox pro and titaniumbackup pro if you want to install apps to sd card apps2sd pro all of these can be tested in free
Version,again nice work congrats enjoy you rooted phone :highfive:
xdacktheresianum said:
Hi phonedriller,
phew, I did it! (Q8S55IN4G2), thanks.
Next step: Have you found a compatible custom recovery? (especially for nandroid backups and for xposed installation)
Would be very thankful for your help!
thanks
xdatheresianum
Click to expand...
Click to collapse
give a hungry man fish and you solve his problem for a day or two
teach him how to fish and you solve his problem for life
phonedriller said:
give a hungry man fish and you solve his problem for a day or two
teach him how to fish and you solve his problem for life
Click to expand...
Click to collapse
hi phonedriller,
...well, i must have been an unlucky fisherman
an app i installed ended up giving me a soft brick (bootloop between qilive icon opening screen - btw still with the "warning" of "device is unsafe etc", i.e. oem still open - and black screen, qilive opening screen etcetcetc)
have cleaned cache; went for factory reset; etc
BUT: am presently stuck when trying to go via ADB (which used to work perfectly before) that somehow the usb drivers don't want to get installed properly. as a consequence, desktop cannot see devices.
and i cannot, for the sake of me, remember how i had succeeded before installing usb drivers.
could you please help?
thx
cktheresianum
xdacktheresianum said:
hi phonedriller,
...well, i must have been an unlucky fisherman
an app i installed ended up giving me a soft brick (bootloop between qilive icon opening screen - btw still with the "warning" of "device is unsafe etc", i.e. oem still open - and black screen, qilive opening screen etcetcetc)
have cleaned cache; went for factory reset; etc
BUT: am presently stuck when trying to go via ADB (which used to work perfectly before) that somehow the usb drivers don't want to get installed properly. as a consequence, desktop cannot see devices.
and i cannot, for the sake of me, remember how i had succeeded before installing usb drivers.
could you please help?
thx
cktheresianum
Click to expand...
Click to collapse
PS: adb will not work if the phone is not booting to the OS
it will work if you manualy place the phone in fastboot AKA bootloader
MODE ,you see if it does not boot to OS then usb service is not working
use power + Volume up to enter the black menu
use the Volume up to select fastboot(bootloader) volume - to confirm
connect the phone to your PC
flash the boot.img, the same boot.img used to root (patched by magisk)
to see is adb is ok just run - fastboot devices
if a serial is presented then all other stuff should work
step 1 - reflash the boot img
step 2 - after the flash finishes - fastboot oem lock
message on the phone screen, confirm yes to lock
OEM
step 3- press power until it turns off
it should now complete the start up (boot)
if not working this method let me now
you can still flash the full factory firmware
using SP Flash Tool v5.17xx
phonedriller said:
PS: adb will not work if the phone is not booting to the OS
it will work if you manualy place the phone in fastboot AKA bootloader
MODE ,you see if it does not boot to OS then usb service is not working
use power + Volume up to enter the black menu
use the Volume up to select fastboot(bootloader) volume - to confirm
connect the phone to your PC
flash the boot.img, the same boot.img used to root (patched by magisk)
to see is adb is ok just run - fastboot devices
if a serial is presented then all other stuff should work
step 1 - reflash the boot img
step 2 - after the flash finishes - fastboot oem lock
message on the phone screen, confirm yes to lock
OEM
step 3- press power until it turns off
it should now complete the start up (boot)
if not working this method let me now
you can still flash the full factory firmware
using SP Flash Tool v5.17xx
Click to expand...
Click to collapse
dearphonedriller,
thank you so much for your speedy help.
followed the steps given by you. all is well, as you predicted, until step 3.
however:
phone (now without the "orange state" message, i.e. oem locked) still bootloops and short of ADB "fastboot devices" the desktop doesn't see the phone (and driver installation continues to fail), as per your PS (thanks!) i guess flashing the full factory firmware ("RC-mt6737...zip" quoted by you in your very first post) is next.
would you please point me to a basic-for-noobs tutorial or instruct me on the step-by-step commands/procedures using this zip file?!
HUGE thanks
ckth
xdacktheresianum said:
dearphonedriller,
thank you so much for your speedy help.
followed the steps given by you. all is well, as you predicted, until step 3.
however:
phone (now without the "orange state" message, i.e. oem locked) still bootloops and short of ADB "fastboot devices" the desktop doesn't see the phone (and driver installation continues to fail), as per your PS (thanks!) i guess flashing the full factory firmware ("RC-mt6737...zip" quoted by you in your very first post) is next.
would you please point me to a basic-for-noobs tutorial or instruct me on the step-by-step commands/procedures using this zip file?!
HUGE thanks
ckth
Click to expand...
Click to collapse
https://www.youtube.com/watch?v=-zaEmj3-prU
turn the phone off, follow the video
flashing the full firmware is actualy easy
https://forum.hovatek.com/thread-13970.html
or searh sp flash tool here on xda
https://www.youtube.com/watch?v=LzyYXAflmOk&t=125s
phonedriller said:
https://www.youtube.com/watch?v=-zaEmj3-prU
turn the phone off, follow the video
flashing the full firmware is actualy easy
https://forum.hovatek.com/thread-13970.html
or searh sp flash tool here on xda
https://www.youtube.com/watch?v=LzyYXAflmOk&t=125s
Click to expand...
Click to collapse
thank you, phonedriller
everything worked perfectly via SPFlash Tool.
and, referring back to our above questions re the possibility of getting TWRP onto the phones, a developer friend of mine writes me this:
>try to flash TWRP:
>Download following files from this link:
>https://mega.nz/#F!qZIgnJRK!5apBfYo1je0ytg-wmA6JMQ
>- Odin3 v3.12.3 (Complete folder)
>- twrp-3.2.1-0-Q8S55IN4G2-20180318.tar
>1. Start your Phone into download mode
>2. Start Odin (Odin3 v3.12.3\Odin3.exe)
>3. Click on Options and unmark Auto Reboot
>4. Click AP and select twrp-3.2.1-0-Q8S55IN4G2-20180318.tar
>5. Press Start and wait until finished (Reset or OK!)
>6. Restart your phone immediatly to recovery mode
>7. In TWRP Recovery click on mount
>8. Set the checkbox checked at system (that system is mounted)
>9. go back and click on advanced
>10. Open file manager
>11. navigate to system/build.prop and click on build.prop
>12. Click on chmod
>13. type: 0644 and hit the accept button on screen or at the virtual
>keyboard on your phone
>14. restart your phone
i haven't tried this, but am wondering whether it might seem "reasonably possible" when reading through it.
thanks
ckth
Do you perhaps have link to Q8S5IN4GP stock rorm? Mine came with malware installed on it. I want to see if those were chinese who preinstalled or or was it decided by Auchan.
tommo1982 said:
Do you perhaps have link to Q8S5IN4GP stock rorm? Mine came with malware installed on it. I want to see if those were chinese who preinstalled or or was it decided by Auchan.
Click to expand...
Click to collapse
On my phone it came from factory and on the firmware file on 2 models , however only kasperky complains about malware on an system app called Helper bla bla bla i think its a false positive(i think) as no other antivirus or playstore ever found anything,but hey better investigate and be safe then sry right :good: maybe a ported cyanogen rom, ive look at a few rom port tutorials but my knowhow is limited + dont even have a working twrp yet, avg/avast/malwarebytes and a few others ,only kaspersky detects malware.
phonedriller said:
On my phone it came from factory and on the firmware file on 2 models , however only kasperky complains about malware on an system app called Helper bla bla bla i think its a false positive(i think) as no other antivirus or playstore ever found anything,but hey better investigate and be safe then sry right :good: maybe a ported cyanogen rom, ive look at a few rom port tutorials but my knowhow is limited + dont even have a working twrp yet, avg/avast/malwarebytes and a few others ,only kaspersky detects malware.
Click to expand...
Click to collapse
I had issues with adds being displayed at home screen and I was not able to close them. I had to use NetGuard to find that FOTA talks to 'adsup' and it is a known malware provider. I learned that some of the system apps try to talk with Alibaba servers and AdOppo (whatever it's called). Kaspersky might not be wrong, actually.
I'm trying to download stock firmware, but I don't know the file name. The website with it is locked, so unless I know exactly what I need, I cannot download it.
phonedriller said:
On my phone it came from factory and on the firmware file on 2 models , however only kasperky complains about malware on an system app called Helper bla bla bla i think its a false positive(i think) as no other antivirus or playstore ever found anything,but hey better investigate and be safe then sry right :good: maybe a ported cyanogen rom, ive look at a few rom port tutorials but my knowhow is limited + dont even have a working twrp yet, avg/avast/malwarebytes and a few others ,only kaspersky detects malware.
Click to expand...
Click to collapse
Yes i noticed the site now asks for a login that i dont have,but it was open to all until recently i have the firmware file in my pc,a few days ago i went to check for firware updates and the site was diferent and closed , in the site the download link was 882912/****** this firmware services at least 3 similar models
phonedriller said:
Yes i noticed the site now asks for a login that i dont have,but it was open to all until recently i have the firmware file in my pc,a few days ago i went to check for firware updates and the site was diferent and closed , in the site the download link was 882912/****** this firmware services at least 3 similar models
Click to expand...
Click to collapse
I guess the best thing would be a lineage or cyanogen ported rom(clean),ps i flashed the phone 2 times because of popups/adds and battery drain,however im aware that having root and installing tones of crasy stuff can fu.. Up any phone cheap or flagship,thus the firmware flashes,i discovered that having malwarebytes(premium)free for 30days keeps the phone clean and working fine,it seems that one is forced to buy from a main stream brand or risk this kind of thing,little to no support,no updates at all,bad security,the problem is certain apps if removed resoult in boot loop like this Helper app
phonedriller said:
I guess the best thing would be a lineage or cyanogen ported rom(clean),ps i flashed the phone 2 times because of popups/adds and battery drain,however im aware that having root and installing tones of crasy stuff can fu.. Up any phone cheap or flagship,thus the firmware flashes,i discovered that having malwarebytes(premium)free for 30days keeps the phone clean and working fine,it seems that one is forced to buy from a main stream brand or risk this kind of thing,little to no support,no updates at all,bad security,the problem is certain apps if removed resoult in boot loop like this Helper app
Click to expand...
Click to collapse
Ps use root + apps2sd or titaniumbackup to stop/disable the bad apps and replace them with playS app,not possible on all apps of course
phonedriller said:
I guess the best thing would be a lineage or cyanogen ported rom(clean),ps i flashed the phone 2 times because of popups/adds and battery drain,however im aware that having root and installing tones of crasy stuff can fu.. Up any phone cheap or flagship,thus the firmware flashes,i discovered that having malwarebytes(premium)free for 30days keeps the phone clean and working fine,it seems that one is forced to buy from a main stream brand or risk this kind of thing,little to no support,no updates at all,bad security,the problem is certain apps if removed resoult in boot loop like this Helper app
Click to expand...
Click to collapse
I'm thinking about Android 8.1 with it's Treble project. I might not be knowledgable enought to compile and flash it, though.
tommo1982 said:
I'm thinking about Android 8.1 with it's Treble project. I might not be knowledgable enought to compile and flash it, though.
Click to expand...
Click to collapse
Flashing is super easy use spflashtools or. Odin compiling a Rom is not , were you able to get the original firmware? You will need the original firware to get the boot and partition info from what i read so far
Unfortunately not. I will ask at the shop where I bought it how to contact tech. It should be freely available. I don't understand why Qilive restricted access to firmware.
I'll post when I learn anything.
Well, you can download the firmware if you know the file name. The bad news is, it seems the stock firmware has malware preinstalled. If there is anyone who could help confirm it. I have the ROM, and I can upload it to Google Drive if needed.
Hi all,
I'm coming back to a question lingering since the very first post here and mentioned again in post #9:
Is there a successful way to install TWRP on this Qilive model?
Re this topic:
- has anybody tried/has anybody been successful with the procedure described in post #9?
and
- has anybody seen the following TWRP builders' version (do an in-page search on Q8S55IN4G2)
https://twrpbuilder.github.io/fr/downloads/twrp/
with the download belonging to it
https://androidfilehost.com/?fid=890129502657591798
???
any successful installations to report???
Wouldn't THAT be great!!??
thanks
xdack
Hello everyone guys, i hope i write in the right section so don't get angry whit me if i don't.
Like i said in the title i have some troubles to make my first root ever on my LG G6 International (h870) let me explain better.
I have enabled developer permissions and enabled USB Debug and OEM Unlock, i have installed on my pc ADB and FASTBOOT and i have unlocked the BOOTLOADER and i have SUPERSU.ZIP in the memory of the phone and TWRP flashed in my phone but the problem starts here, after i going in recovery mode whit POWER BUTTON + VOLUME- and do all the process to start TWRP the phone shows me the TWRP image but it don't start and after few seconds it reboot into my normal android recovery.
i really apprecciate if some of you guys wanna help me out whit this.