Please help me!!
I have tried all the systems described in the wiki without turns out to you.
Could you tell us which device do you have?
- HERM 100 / 200 / 300
- IPL & SPL versions
- Previous rom you had installed
- Language
And paste the output of these Bootloader commands:
Code:
info 2
info ?
checkimage
Model is Herm100 O2 XDA Trion German Language update to WWE (xxp://xda:[email protected]/Uploads/Hermes/CHT9000_ENG.exe)
I do not succeed to load nobody rom stop all to the maximum to 25%
I have tried all the ways also making to leave pda in boot mode
How them I must send those commandos through tty?
Put the device in bootloader mode (SIDE OK + POWER + RESET), connect it to the computer though USB cable, open RomUpgradeUT.exe and start the upgrade process, if it fails, do not disconnect the device from USB and start the upgrade again.
If that fails, download mtty.exe, open it, select USB, click OK, and type in the bootloader commands I told you in my previous comment.
For more info look at the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
No upgrade!!
info is:
info 2
HTCSO2___102"qŒ)HTCE
info ?
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19800
Partition[3], type=0x4, start=0x1C800, total=0x1E000
CE Total Length(with sector info) = 0x39E4000
CE CheckSum Length(without sector info) = 0x3900000
checkimage
IPL CRC checksum = 0x68F14038
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0xB17AD2A4
ExtROM CRC checksum = 0x1B80FFB9
Radio Image CRC checksum = 0xEF2E0780
----------------------
Tanks
Emblema said:
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
Click to expand...
Click to collapse
This seems not good to me
I guess you can boot the currently flashed rom and use the device, but you cannot flash a new rom, right?
Emblema said:
IPL CRC checksum = 0x68F14038
SPL CRC checksum = 0x3BF03635
Click to expand...
Click to collapse
Your IPL & SPL checksums are different from mines, which IPL & SPL versions do you have? The version numbers are shown on the device screen when you put it in bootloader mode.
pof said:
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
This seems not good to me
I guess you can boot the currently flashed rom and use the device, but you cannot flash a new rom, right?
Click to expand...
Click to collapse
yes I use the dispoditivo but I do not succeed to load one new rom
Emblema said:
IPL CRC checksum = 0x68F14038
SPL CRC checksum = 0x3BF03635
Your IPL & SPL checksums are different from mines, which IPL & SPL versions do you have? The version numbers are shown on the device screen when you put it in bootloader mode.
Click to expand...
Click to collapse
Herm100
IPL-1.00
Herm100
SPL-1.04
its possible to try to put within pda a rom dumped from an other? (.raw)
if, like?
Help me, my pda is 1/2 dead
Not possible at the moment. I think you'll need to format the flash or try to repair it using the bootloader, but I don't know the exact commands. I'll have a look at it and try to find a solution for you. Did you had any problems during any previous upgrade? Did the power went out while upgrading or did you disconnect the device?
What you can do is install HDD Usb Monitor, put it in capture mode and try to flash a new rom, then you should be able to see the exact error or reason why it fails from there. If you post the error here it will be useful to diagnose the exact problem and try to find a solution for it.
Hi Pof,
Today they are successful to put within the rom dell imate after six tried to you, for the moment aspect that decoy the rom Italian and then we try and we see if it continues to give stessp the problem. Thanks thousands for the availability.
Tanks
Help me - MDA Vario 2 - M300
I also has same prob with Emblema. My PPC only connect to PC in bootloader mode. I cannot start my PPC after fail upgrade ROM.I tried many times to upgrade but it not success (stop at 0%)
Pls help me to recover or upgrade new ROM
MDA vario II M300
IPL 1.01
SPL - 1.04
Re: Help me - MDA Vario 2 - M300
linhmuc said:
My PPC only connect to PC in bootloader mode. I cannot start my PPC after fail upgrade ROM.
Click to expand...
Click to collapse
Enter the bootloader using mtty, when you see the "USB>" prompt type in these commands (do not copy-paste!):
Code:
USB> set 14 0
USB> task 8
The device should restart and boot the OS. For more info, see this page on the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
I tried 2 command , it successed but hold at windows mobile screen. I want to format ROM and install new ROM, how do i do?
Pls help me.
Thanks.
Have you tried flashing every available ROM for the Hermes? Always get an error?
Can you post here the output of 'info 8' command in bootloader?
Thanks for reply
Here is the result executed command info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1B400
Partition[3], type=0x4, start=0x1E400, total=0x1C400
CE Total Length(with sector info) = 0x3D72000
CE CheckSum Length(without sector info) = 0x3C80000
I also tried other ROM upgrade but it hold at 0%
Everything seems ok to me... sorry for not asking before, but can you post the output of 'checkimage' command?
Which device is it, and which was the last ROM you had on it?
Did you try to unlock it or something before it break?
My PPC is MDA vario II - Herm300
I tried unlock with HTC_Uni_SIM_Unlock_v1 and have an error. From that I cannot start my device.
I execute checkimage command:
IPL CRC checksum = 0xA2BD7A6
SPL CRC checksum = 0x3BF03635
CE CRC checksum = 0x458E70C0
ExtROM CRC checksum = 0x10D845D9
Radio Image CRC checksum =
it stop at "Radio Image CRC checksum = "
I think you have the same problem fluffcat1 describes here:
http://forum.xda-developers.com/viewtopic.php?t=61396
After runing the HTC Universal Unlocker you've screwed the radio of your device, there is no radio rom present and no security area, radio rom upgrade won't success.
There is no known solution to this problem yet, do you have warranty or can get a replacement unit?
@linmhuc:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
to prof:
I run command info 2, but it not execute, it hold, how do i know my PPC CID ?
Related
Hi everybody,
I bought my V1605(French SFR) today and I decide to unlock it with HTC uni Unlock V1 in order to work with my business SIM card.
At the end of the unlocking I've got an error, telling me to try to install again. After resetting my V1605, It stop on Operator logo. I try hard reset but nothing happened, I'm still stuck on operator logo.
Bootloader is in 1.04.
My V1605 is no longer recognized by activsync, I tried with mtty, but impossible to connect on usb.
I tryed to reinstall the original rom, but V1605 can't be find. Same for other rom.
I tryed everything on hermes upgrade Problem page, but nothing works.
When I try to update rom by microsd, it's not working. I have read the wiki page.
Have you got any idea ? You'll be my hero... I'm really in a dead end.
Thanks in advance,
Geof
- disable usb connections on activesync
- put hermes in bootloader mode and connect to computer usb port
- start usb monitor capture ("complete view")
- start update of original rom (retry two times if it fails first)
- when finish, export usb monitor capture to ANSI text format, and attach it here.
Thanks for your help.
It seems that my V1605 is disconnecting when I try to update
oops! the file shows nothing useful. seems disconnected after the first usb setup packet.
When you put it in bootloader mode and connect to usb port, do you see in the bottom part of the screen the string "SERIAL" changes to "USB"? or it stays "SERIAL" ?
Have you tried a different usb port on the same computer? or even a different computer?
Do you get any error when trying to flash from SD card? do you see the "checking...." ?
I tried on 2 computers and on each usb ports...
When I try to update, it stays on usb and never come to serial.
With the Microsd, there is a very very very fast check on card (less than 1/2 seconde), and it stay on bootloader. It seems that it wouldn't want to launch anything from the Microsd.
I retried to use mtty and it connects, but what to do.
I tried with the himalaya rom to get a better USB monitor file. It stuck on white screen on V1605 at 0% on PC.
G3oF said:
With the Microsd, there is a very very very fast check on card (less than 1/2 seconde), and it stay on bootloader.
It seems that it wouldn't want to launch anything from the Microsd.
Click to expand...
Click to collapse
Try it several times... sometimes it is a bit hard to make the bootloader read the image. Make sure you only put the french voda rom NBH file renamed to HERMIMG.nbh on the microSD card, and nothing else.
G3oF said:
I retried to use mtty and it connects, but what to do.
Click to expand...
Click to collapse
checkimage
info 2
info 7
info 8
set 14 0
task 28
...
USB>checkimage
IPL CRC checksum = 0xAB6DDB32
SPL CRC checksum = 0x3BF03635
CE CRC checksum =
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a
Device Name: H, Bootloader Version : 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19D00
Partition[3], type=0x4, start=0x1CD00, total=0x1DB00
CE Total Length(with sector info) = 0x3A86800
CE CheckSum Length(without sector info) = 0x39A0000
USB>info 2
USB>set 14 0
Write Nand Success
HTCST ÚÈÒHTCEUSB>
USB>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 461
Storage Total block: 475
Total Bad Block in CE: 0
NeedToEraseBlockStart: 474
Storage format success
As you can see some command not working. It seems those commands interrupted the USB link. Have you ever seen this before ????
I continue to try updating by sd, but seems not working.
Thanks for your help
Do you think I have to send it to technical center ?
Probably it's a good desition if you can't fix it by any other way.
I ask for replacement and thy agreed. I'm surprised but very happy. I'm not sure to try to unlocked it right now ;-). Thanks again for your help
After trying to fix MapKing problem by flashing different SPL and OS, I have a new problem: shows "no gsm" then hang at windows mobile splash screen.
I have SPL 1.04, HTC_BOOT 1.08, and the wiki says "Flash a ROM with SPL-1.09+KITL enabled OS", but how do I know which OS has KITL enabled?
In addition, all the ROMs are now in RapidShare, and I have problem downloading. Could anyone please help share it in other places?
kuekpeow said:
After trying to fix MapKing problem by flashing different SPL and OS, I have a new problem: shows "no gsm" then hang at windows mobile splash screen.
I have SPL 1.04, HTC_BOOT 1.08, and the wiki says "Flash a ROM with SPL-1.09+KITL enabled OS", but how do I know which OS has KITL enabled?
In addition, all the ROMs are now in RapidShare, and I have problem downloading. Could anyone please help share it in other places?
Click to expand...
Click to collapse
You just need to spend more time reading the wiki...
trashcan said:
You just need to spend more time reading the wiki...
Click to expand...
Click to collapse
What I understand from WIKI is that all ROMs with SPL-1.06, SPL-1.09, or SPL-1.11 have KITL enabled. However, no ROM from Dopod has SPL-1.09 so I will need to flash the ROM from either HTC or Cingular. However, I'm worried that if I still can't get KITL mode, then I can't recover it myself using PB+KITL method. I understand that only SPL-1.04 has the CID bug to be able to flash other operator's ROM, therefore I would probably be stuck with HTC or Cingular splash, which will definitly void my Dopod warranty.
Therfore I will really appreciate if any knowledgable and helpful person could confirm with me that I should proceed to flash shipped SPL-1.09 ROM from other Operator to get KITL enabled OS, in order to use PB+KITL method to recover my bricked Dopod 838 Pro. If this is not a fool proof method, then I would rather sent the unit to Dopod Service Centre for repair...
I also posted in another thread asking for help ("dead hermes? corrupted radio? Post comments here" http://forum.xda-developers.com/showthread.php?t=286755&page=89), but have not got any reply yet...
Original Config: SPL=1.04, HTC_BOOT=1.08, Radio=1.38.00.10, ROM=Jasjamming WM6 v1.2.
What Happened: Flash by CustomRUU v4.2 Forced SSPL: SPL=1.04, HTC_BOOT=1.08, Radio=1.06.00.10, ROM=Dopod 1.23.707.4.
Current Problem: HTC Innovation Splash will show No GSM after few seconds, then hang at WM5 Splash. info 2 does not return SuperCID string anymore, and cannot boot into KITL mode.
Failed Recovery: Flash WM6 LVSW 2007-03-26 result in ERROR [262]:UPDATE ERROR.
USB>task 32
-> Level = FF
USB>info 2
->CID: Wait Interpreter timeout
HTCSUSB>
USB>info 3
->HTCSH
USB>info 7
->HTC Integrated Re-Flash Utility, Common Base Version: 1.50a
Device Name: H, Bootloader Version: 1.04
Built at: May 26 2006 20:17:35
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version= 0x4
Main Board version=0x6
USB>info 8
->Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x0x1CD00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
Already answered in the brick thread.
Cuivienor said:
Already answered in the brick thread.
Click to expand...
Click to collapse
Thanks
1. problem started when trying to down grade cingular 8525 from Black Satin 2.10.Olipro for warranty return.
2. Used mrvanx downgrading guide to wm5.
3. Used the following Rom to downgrade:
New cing/ATT aku3.5.2 WWE_2_1_.15.502.3_6275_1.40.30.00
Oli SPL 1.40, OS, Ext Rom, and 1.40 radio
http://forum.xda-developers.com/showthread.php?t=302092
4. after that I'm stuck @ tricolor screen with IPL 1.03 and SPL 1.40.Olipro
5. Used mtty without problem.
Cmd>info 2
HTCSSuperCIDHTCE
Cmd>info 4
HTCSCWS__001Ùü¤HHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1D500
Partition[3], type=0x4, start=0x20500, total=0x1A300
CE Total Length(with sector info) = 0x41A2800
CE CheckSum Length(without sector info) = 0x40A0000
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x91BAA20E
CE CRC checksum = 0x91AAF967
ExtROM CRC checksum = 0x8026B8EF
Radio Image CRC checksum = 0x967D13F3
5. Tried flashing with POF's unlocker v3 from SD flash successful.
I can flash with any rom from cingular's original wm6 to any rom without
any problem but can't boot.
When I press power button, the screen goes blank and green light but does
nothing else.
6. I've have read all the thread from Dead Hermes to HardSpl stickies and
searched the forums for 2 weeks now but can't find an answer. The
problem is that I have to returned the phone in 2 days or cingular's billing
me for the phone.
7. I tried flashing 1.10.Olipro, 2.10.Olipro, etc to replace 1.40.olipro from sd.
I says each time successful flash but during reset it remains the same it
stuck in green light blank screen and when I enter the bootloader mode it
says the same IPL 1.03 and SPL 1.40.Olipro.
Thanks in advance. any help is greatly appreciated. I'm stomped.
1. problem started when trying to down grade cingular 8525 from Black Satin 2.10.Olipro for warranty return.
2. Used mrvanx downgrading guide to wm5.
3. Used the following Rom to downgrade:
New cing/ATT aku3.5.2 WWE_2_1_.15.502.3_6275_1.40.30.00
Oli SPL 1.40, OS, Ext Rom, and 1.40 radio
http://forum.xda-developers.com/showthread.php?t=302092
4. after that I'm stuck @ tricolor screen with IPL 1.03 and SPL 1.40.Olipro
5. Used mtty without problem.
Cmd>info 2
HTCSSuperCIDHTCE
Cmd>info 4
HTCSCWS__001Ùü¤HHTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.60d
Device Name: HERM100, Bootloader Version : 1.40.Olipro
Built at: Mar 30 2007 15:10:47
Copyright (c) 1998-2007 Modified By Olipro - Hard-SPL
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x5
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x1D500
Partition[3], type=0x4, start=0x20500, total=0x1A300
CE Total Length(with sector info) = 0x41A2800
CE CheckSum Length(without sector info) = 0x40A0000
Cmd>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x91BAA20E
CE CRC checksum = 0x91AAF967
ExtROM CRC checksum = 0x8026B8EF
Radio Image CRC checksum = 0x967D13F3
5. Tried flashing with POF's unlocker v3 from SD flash successful.
I can flash with any rom from cingular's original wm6 to any rom without
any problem but can't boot.
When I press power button, the screen goes blank and green light but does
nothing else.
6. I've have read all the thread from Dead Hermes to HardSpl stickies and
searched the forums for 2 weeks now but can't find an answer. The
problem is that I have to returned the phone in 2 days or cingular's billing
me for the phone.
7. I tried flashing 1.10.Olipro, 2.10.Olipro, etc to replace 1.40.olipro from sd.
I says each time successful flash but during reset it remains the same it
stuck in green light blank screen and when I enter the bootloader mode it
says the same IPL 1.03 and SPL 1.40.Olipro.
Thanks in advance. any help is greatly appreciated. I'm stomped.
Hi,
I have been working for days and nights through wiki (you guys do a great job) and reading forums on the issues of bricked hermes, and wanted to know am i wasting my time with mine as follows;
Dopod 838 pro (Hermes100)
IPL-1.01
SPL-1.09 (BEFORE 1.04)
Corrupted CID, IMEI, RADIO (NO gsm)
USB>task 32
CID: Wait interpreter timeout
Level = FF
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a S024
Device Name: H, Bootloader Version : 1.09
Built at: Nov 7 2006 22:59:17
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
USB>info 4
HTCSDOPOD001Û<wHTCEUSB>
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0xD(13) is BAD block !!!
USB>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x91BDD7D5
CE is None.
ExtROM is None.
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
spl-1.04 which allowed me to flash original roms but hung at 14%, i guess this is when the rom installs the radio part of the rom which mine was corrupt when trying in the first instance to update radio rom 1.54.30.10 which got me in this mess.
So its looking like service center i guess?
Were you flashing it at the time it stopped working? What is the history?
history i had a crc10.2 version rom, flashed supercid, flashed hardsplv7, then flashed original dopod shipped 3 rom 3.54.707.4 radio 1.47.30.10 worked great. Then flashed upgraded radio 1.54.30.10 and then bricked. Downgraded spl to 1.01mfg using mtty and then it corrupted my cid and imei. so now i left with a corrupted imei,cid and radio.
Did you use the "task 2a" command to fix bad blocks?
Might help....
task 2a command only works with mfg bootlooder eg spl-1.01 MFG, i cant go back to mfg 1.01 because your cid needs to be supercid. so my is answer no regrettably. iam thinking with spl-1.09 i could flash the factory rom via sd card? but where do you get factory roms from not upgrades considering my cid is locked.
There were a heap of roms on the wiki (dont know if they're still available) both cooked and stock roms. Who you with? Might be an idea to let people know as they might be able to supply links... Just a thought...Cheers
i am currently with 3, but i bought the phone used not sure who it was prior.
only a thought but are using a usb hub,if so stop and connect directly,dont know if my problems were exactly the same but 4 days of frantic flashing and stomach ulceration were instantly relieved by doing the above,good luck,btw the 3 rom from dopodasia is still available online and used with a mod wrapper would allow a card intall
i have tried hut..3 roms via flashing usb and by sd get error via sd not allowed. i guess the roms online are upgrades where i need the factory wm5 rom.
wm5 rom is a good idea and there are plenty stock wm5/6 roms floating around,but use the modded wrapper to install via usb,no hub,many people swear by at&t roms to get them out of trouble
thanks Stevie boy for your ideas and comments, still having problems i have tried all the dopod roms on xda developers using the custom RUU wrapper so i can select my spl which is spl-1.09 and i get invalid vendor id. if i had SPL-1.04 it has a bug where i leave the phone connected to USB and run the wrapper twice and it updates but this is not working now on spl1.09 bummer.
i feel your pain man,all i can say is that the wiki saved me,there is so much info there its a bit hard to see your way thru but you should be able to work it out.i assume you can still force bootloader is so it seems all is not lost try pm to mr vanx to get more specific advice
.....
I'm with the same problem...
can anyone give more advices...
_______________________________________________
Spv m3100
USB>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.50a S024
Device Name: H, Bootloader Version : 1.09
Built at: Nov 7 2006 22:59:17
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
USB>task 32
CID: Wait interpreter timeout
Level = FF
USB>checkimage
IPL CRC checksum = 0x24C42773
SPL CRC checksum = 0x7725B228
CE is None.
ExtROM is None.
Radio Image CRC checksum = Checksum: Wait interpreter timeout
0x0
USB>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0xD(13) is BAD block !!!
how to install???
hello guys,, since i am new with smartphones,, just bought a htc touch,, but don't knowq how to install the T9 pad,,
can anyone help me???
Is the HTC touch even a Hermes???
Me too, this posts seem no one able to fix it.
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: HERM100, Bootloader Version : 2.03
Built at: Jun 16 2007 01:57:22
Copyright (c) 1998-2006 High Tech Computer Corporation
CPU ID=0x41129200
Main CPLD version=0x5
Upper CPLD version=0x4
Main Board version=0x6
Cmd>info 8
Block 0x0(0) is Reversed block
Block 0x1(1) is Reversed block
Block 0x2(2) is Reversed block
Block 0x3(3) is Reversed block
Block 0x4(4) is Reversed block
Block 0x5(5) is Reversed block
Block 0x6(6) is Reversed block
Block 0x7(7) is Reversed block
Block 0x8(8) is Reversed block
Block 0x9(9) is Reversed block
Block 0xA(10) is Reversed block
Block 0xB(11) is Reversed block
Block 0xC(12) is Reversed block
Block 0x15E(350) is BAD block !!!
Block 0x184(388) is BAD block !!!
Block 0x1CF(463) is BAD block !!!
Block 0x1E8(488) is BAD block !!!
Block 0x2EA(746) is BAD block !!!
Block 0x2F3(755) is BAD block !!!
Block 0x311(785) is BAD block !!!
Block 0x364(868) is BAD block !!!
Block 0x3C6(966) is BAD block !!!
Partition[0], type=0x20, start=0x2, total=0x18FE
Partition[1], type=0x23, start=0x1900, total=0x1700
Partition[2], type=0x25, start=0x3000, total=0x19E00
Partition[3], type=0x4, start=0x1CE00, total=0x1DA00
CE Total Length(with sector info) = 0x3AA7000
CE CheckSum Length(without sector info) = 0x39C0000
anyone can help ?
Try "task 2a"... Thats the command to fix bad blocks.
ultramag69 said:
Try "task 2a"... Thats the command to fix bad blocks.
Click to expand...
Click to collapse
Thanks for the reply, I tried tat too. nothing happend.
I tried almost everything, like cid unlocker, flash radio, flash back to original rom, flash from sdcard...etc..
Now trying to get the window platform builder.
You need to downgrade your SPL to 1.10 for those commands to work. If you haven't, nothing will work...
ultramag69 said:
You need to downgrade your SPL to 1.10 for those commands to work. If you haven't, nothing will work...
Click to expand...
Click to collapse
The problem is, I can't flash any of the rom. radio, hard spl, or others.