Japanese ROM from DoCoMo hTc Z has been uploaded to XDA-Developers FTP and added to the Hermes wiki, you can find it under the Available Original Shipped ROM Versions.
Notes on this ROM:
ROM Version: 1.23.731.2 06/24/06
Radio Version: 1.06.00.10
Bootloader: 1.04
Language: JPN (Japanese)
CID: DOCOM801
As you can see this is nothing new, but I guess it will be useful for people with this CID to be able to downgrade to bootloader 1.04.
Enjoy
Hi pof,
Thanks for that. I tried this to flash my X01HT after unlocking it with imei-check but with no luck. RUU went successufully till the last screen and I hit the upgrade but it returned an error saying something like this RUU cannot be used for the device. Bootloader is now 1.04 and the device should be SuperCID with imei-check. The only thing I can think of is that I upgraded the radio to your 1.2. Would that screw SuperCID? I appreciate your advice in advance.
Thanks,
harryk
harryk1372: If you are in 1.04 bootloader just run the upgrade utility again without disconnecting the device or start the upgrade in bootloader mode to bypass CID checking.
If it is really SuperCID then you shouldn't have seen this error.
Hi pof,
Thanks very much for getting back to me so quickly.
I ran the upgrade in the bootloader mode. I thought that I don't have to run it twice if the device is already at the SuperCID state and didn't run the update twice. I'll try it again when the device is fully charged as the battery is now down to like 30%.
I'll post the result again when I am done. Thanks again for your prompt advice. You're the man and I really appreciate your efforts taking us thus far in cracking Hermes.
Regards,
harryk
Hi pof,
The device looks like it was not in the SuperCID state and RUU went fine with the second run with no error. However, the upgrade failed when it hit exactly 47% no matter how many times I tried it. Lucky that I did not brick my device but of course it seemed to lack some of the components and it did not even have the Connections setting to set up the Internet access. Also, AutoRun and cabs in the ExtRom didn't take any effect either although the cab files were there.
I decided to flash the TyTN ROM instead and that was successful. That is fine as I only use Japanese occasionally and I didn't really want the Japanese MUI so I will keep it as is. Perhaps I will tweak it a little to be able to use Japanese with loading the Chinese nls, Japanese font, Japanese IME and so forth just like I did with my Universal.
Thanks again.
harryk
Does anyone succeed in flushing Docomo ROM to X01HT?
After unlocking my X01HT,
the annoying message http://forum.xda-developers.com/showthread.php?t=282073&p=1048193
appears again and again, even if I use SB_USIM.
Especially when I write SMS message, it will disturb me over and over.
I try to flush the Docomo ROM to my X01HT and hope to receive your help.
s2k7 said:
Does anyone succeed in flushing Docomo ROM to X01HT?
After unlocking my X01HT,
the annoying message http://forum.xda-developers.com/showthread.php?t=282073&p=1048193
appears again and again, even if I use SB_USIM.
Especially when I write SMS message, it will disturb me over and over.
I try to flush the Docomo ROM to my X01HT and hope to receive your help.
Click to expand...
Click to collapse
fyi...
http://forum.xda-developers.com/showthread.php?t=283177&page=2&highlight=qtotter
I always downgrade my JASJAM using I-Mate shipped ROM
s2k7 said:
Does anyone succeed in flushing Docomo ROM to X01HT?
After unlocking my X01HT,
the annoying message http://forum.xda-developers.com/showthread.php?t=282073&p=1048193
appears again and again, even if I use SB_USIM.
Especially when I write SMS message, it will disturb me over and over.
I try to flush the Docomo ROM to my X01HT and hope to receive your help.
Click to expand...
Click to collapse
i use the docomo rom on my x01ht. it's ok. i have no problem with it at all.
a friend of mine uses a sim-unlocked x01ht (/w the original s/b rom) with sb_usim, but she does not get such a msg at all. do you use a s/b sim?? if yes, i suppsoe you did something wrong...
X01HT Unlocking Problem
I've got this X01HT a few days ago from S/B shop but when I tried unlocking it the result was no good using my cable. I read from other site that X01HT released from December 2006 cannot be unlocked. Please give me some clarifications on this and also, is FLASHING on lower rom version even in english version can resolve the problem...? Your response will so much appreciated.
Thanks in advance.
At the moment it's not possible to unlock X01HT devices wich where bought after 12/1/2006 and have bootloader version 1.09 and RadioROM version 1.14.0.10! Please be patient.
To the experts, I need some advice. I intend to get a X01HT, already unlocked and flashed with the dopod 838 pro firmware. However, I intend to flash back the Japanese shipped rom :
RUU_HER_DoCoMo_1.23.731.2_1.06.00.10_JPN_SHIP.zip
What are the requirements esp where :
Bootloader (SPL)
Latest Radio Bootloader (HTC_BOOT)
Or since its unlocked, do I just go to the bootloader mode and flash direct? Any side effects if I do so, since its changing from an english rom of another clone (Dopod 838 pro, WM6)?
I am not even sure if the RUU_HER_DoCoMo_1.23.731.2_1.06.00.10_JPN_SHIP.zip rom is WM5/6. Please advice, thanks..
Related
Hi,
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
Please help.
Thanks
If your device is still working ok as a PDA then hopefully it just screwed up the radio update of your device.
Try reflashing the Radio only
Look Here
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Post back with results
Regards
S.K
EDIT: Sorry only works on 1.04 bootloader only. Afraid your gonna have to wait for Pof to come up with a 1.06-1.04 workaround
Hi S.K,
Thanks for the info. I have now tried installing the HERM_1.20.31.10_type2_radio_fixed upgrade but unfortunately the radio upgarde crashes also. It all seams to go well, (after using MaUpgradeUt_noID.exe twice) the phone says "Upgrade Radio Stack Please wait" and the progress bar appears on the PC but then after 10 mins I get an ERROR 114: RADIO ROM UPDATE ERROR.
Do you think this might be becuase the last upgarde partly installed bootloader 1.06?
Any other suggestions - I'm desperate to get the hpone on M3100 working again.
Thanks
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Please post USB monitor capture, otherwise can't help u.
Hi Pof,
Thanks for the offer, I will sort out the usb software on Monday. Are there specific actions that I should try, obvioosly I will usb monior everthing I do but I want to keep it to the point and not waist yr time trailing through huge log files.
Cheers
BTW - I have tried all options of recovery, such as attempting to install the latest radio and trying to install the new rom from an sd card, trying several roms and using imei unlocker - all without any joy.
I think the problem is that I have partially installed radio and bootloader 1.06 so I can't fix the problem.
Thanks again.
@wotthefok:
For me is faster to look at the usb log file, then I exactly know why the upgrade fails, otherwise I have to decode it from your feedback and I can't be really sure. Check the "upgrading problems" page on the wiki, if none of the steps there seems to fix your problem, post USB monitor log please.
Log Files as requested
Hi,
I have captured information using usb monitor and attached the zipped log files for your attention.
The first is called USB_monitor_log_Herm_120Radio_twice. This log details attempting to install the HERM_1.20.31.10_type2_radio_fixed upgrade, and running it twice - just in case.
The USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_twice.zip details attempting to install the RUU_HER_Cingular_1.34.502.1_1.16.00.00_wwe_cws_ship upgrade, simply using the standard ROMUpgradeUt.exe method. This generates the expected Vendor ID error.
My primary focus is to install the radio upgare or download my bootloader to 1.04. The PDA part of my m3100 does now freeze occasionally but at least functions whereas the phone is completely dead.
Thanks in advance.
Please attach capture in *ANSI TEXT FORMAT*, the .lgs file you zipped is totally unuseful
Edit -> Export and Save as type "ANSI Text files".
Also make sure you export in "COMPLETE" view, see the wiki for more details.
OK, Spot the novice.... I have now created a txt log file that captures activity of me running the 120 Radio upgarde - but only once this time. I still had to zip the file due to it's size. Hope this is OK.
I'll send the other logs within the next couple of hours. Please let me know if the output I have sent so far is acceptable?
Thanks
wotthefok said:
Please let me know if the output I have sent so far is acceptable?
Click to expand...
Click to collapse
No, it's a "basic" capture, you have to export a "complete" capture:
Start USBMonitor.
File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
In the upper part there are two tabs: basic and complete. Click on "Complete".
Right, Try again (duh!) OK, I've tried to keep the log files names as self-explanitory as possible... USB_monitor_log_Herm_120Radio_run1.zip is the r20 radio upgrade, 1st run and USB_monitor_log_Herm_120Radio_run2.zip the second run - without disconneting or resetting the device.
USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_ran_twice.zip is the Cingular upgrade run via the ROMUpgradeUt.exe, again run twice without disconneting the device.
Hope I got it right this time.....Please let me know if there is anything else I can do.
Thanks.
This time you got the captures right
- You're on bootloader 1.06: You don't have 'rtask' command, you won't be able to do any radio upgrade only.
- Your device is not CID unlocked (Security level=FF, unprivileged)
- The bad flash caused the CID area to corrupt (CID: Wait interpreter timeout)
- When flashing a full ROM you get a CID not allow (255) this is because your corrupted CID doesn't match the CID on the ROM.
The radio part is screwed, you could have fixed this if you where in bootloader 1.04 by flashing a full ROM, but as you are in 1.06 you can't because of CID checking. But you're lucky because the OS ROM is intact and you can boot the OS, you should be able to downgrade to bootloader 1.04 from OS and flash a full ROM after, which will hopefully fix your radio.
Just wait until a solution to downgrade bootloader is available (I'm working on it).
Hi,
As I suspected.... Suppose it's not all bad news though - just means that I have to be patient and use my communicator once more. Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
I have already got a IMEI-CHECK sim unlock from where I originally got the M3100 unlocked from Orange to work on o2. That said, I have run either unlocker 2 or 3 with the .unl that I know worked I now get
HTC HERMES v3c unlock
Starting communication.........
Checking device..............ERROR
The device you try to unlock is not supported.
Please contact your supplier site.
Device is rebooting
Press any key to quit this application.
I'm currently chatting to the guys at IMEI-CHECK re this problem.
Anything else I can do to assist you in anyway??
Cheers
wotthefok said:
Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
Click to expand...
Click to collapse
They have it (M3100v3cUnlock.exe), but it will not work on your device because your IMEI is corrupted and their unlocker will not be able to read it and to check/compare with the .unl key file.
Hi,
Just a quick update. The guys at MIGsofT LTD have VERY VERY generously said they'll have a look at the problem for me so my phone will be winging it's way to them today.
Thanks for your assistance and helping me be certain of the problem and to better understand the root cause.
Hope this information will prove useful to others.
Another quick update...
The guys at IMEI-CHECK (MIGsofT LTD) have rectified problems with my handset and managing to reinstall bootloader 1.04 in the process!!
They also turned my phone around in under three days and only charged me the cost of postage! I had previously been a customer of theirs but it was still a very generous and helpful offer and I would certainly pay for the service than have a duff handset - after all £250 + for a paperweight is rather excessive....
If you're experiencing a problem like mine why not get in touch with them and offer them money to have a look at your handset? No Guarantees but it seemed like my last chance, for a while anyway.
Praise to IMEI-CHECK for a brilliant service - they are King of the day !!
Hello all,
I got a friend of mine who came to me with a device-password locked Hermes, which password he cannot recall (actually his girlfriend...). I said I would be willing to give him a hand to unbrick the device. The problem is that I cannot install any ROM on the device, coz I got an error connection right after the screen goes white and the percentage count should normally start.
So I put the Herm in Bootloader (spl-1.06) and try to flash the OliPro Bootloader. The procedure goes correctly until the step where the upgrade itself should begin, counting from 0%... here, I got:
ERROR [262]: Update error: communication error.
I also tried to flash a ROM directly, but since my Bootloader is 1.06, I didn't find a CID match ROM, so it also failed. The Herm is now not bricked, but it stays at the password input screen, so cannot enter windows properly.
Any help on this?
Thanks,
Ionutz
Interesting since you are trying to go around something HTC probably did not want for people to go around due to security....
agovinoveritas said:
Interesting since you are trying to go around something HTC probably did not want for people to go around due to security....
Click to expand...
Click to collapse
yes, i grih you,and normally i wouldnt even try to do such thing, if it hadnt been for a friend of mine which i know.
besides i would like to learn more stuff about my Herm and this is one thing I havent seen discussed here, although i keep reading xda forums for such info.
just found the solution: i flashed another ROM with same CID since my BL was 1.06, but with BL 1.04. After that, I managed to flash any other ROM and automatically upgrade the SPL to 1.10 or 2.10 Oli accordingly.
If any of you interested and dont get the short explanation, PM me.
cheers,
Io, owner of 2 kicking TyTn's
BL 1.06 didnt allow devices with a different CID to be flashed,
eg: my TyTN had the CID: QTEK001 so i couldnt flash a ROM destined for a device with CID: VODAP001
But BL 1.04 had a bug where you COULD flash any ROM to the device regardless of the CID, the first attempt shows a vendor ID error, then try again and it will flash no problem.
The simplest way I would have got past the device security problem would have been a hard reset.
mrvanx said:
BL 1.06 didnt allow devices with a different CID to be flashed,
eg: my TyTN had the CID: QTEK001 so i couldnt flash a ROM destined for a device with CID: VODAP001
But BL 1.04 had a bug where you COULD flash any ROM to the device regardless of the CID, the first attempt shows a vendor ID error, then try again and it will flash no problem.
The simplest way I would have got past the device security problem would have been a hard reset.
Click to expand...
Click to collapse
I know the details about BL 1.04 vs 1.06, thats why I flashed a BL 1.04 ROM, but with the same CID QTEK_001, or smth.
I have to admit though that I never ever thought about doing a simple hard-reset. I guess it would have been to easy, I jumped to more complicate scenarios. Thanks for the help anyway, i gotta learn that.
Thanks mrvanx, glad I read down the whole thread to the part about a simple hard reset working. I lent my 8525 to a friend, thinking he might be interested in buying it, then he didn't have the money, and after I listed it on ebay today, I charged it up to flash to ATT stock, found it password locked, called my friend a few times just getting his voicemail, so tried flashing, and it said the Hermes wasn't connected to the PC...
I figured there would be a solution here at XDA..and POOF, like magic here it is!
So yes, all I had to do was a hard reset, tested and it works, and it was simple, so thanks again mrvanx, although this thread is very old, glad I found it LOL!
Hi,
First many thanks to all people here at the forum who makes the day better and more interesting for mobile nerds like me. I have been lurking around here for a long time and enjoyed every minute of it.
My problem :
Since my x7500 is SIM unlocked and with a standard setup as far as I can see I tried the HTC VM6 Rom flash without CID unlock.
That was stupid. Very stupid, since I don't have the providers orginal ROM available.
My x7500 will not accept the HTC VM6 ROM and is stuck in Bootloader with "USB" at the bottom of the screen when connected to my PC. Hard reset does not start the normal "installation"
When I start the VM6 flash program I get the famous "provider error message"
Is there any possibility to unlock the CID in Bootloader or "flashing" the bootloader to use the original ROM image at my device for a re-install ? In that way I could use the X7500 unlocker in VM5 and then flash to VM6 after.
If not re-installing the original ROM or unlocking the CID is possible I guess my x7500 is seriously bricked.
I am sorry if the answer to my problem can be found in other treads here. I have searched and read a lot without any success. I know now that I should have unlocked the device before trying to flash -> can only blame my one stupidity.
I will be very happy for every advice.
Greetings, Eric
EricBr said:
Hi,
First many thanks to all people here at the forum who makes the day better and more interesting for mobile nerds like me. I have been lurking around here for a long time and enjoyed every minute of it.
My problem :
Since my x7500 is SIM unlocked and with a standard setup as far as I can see I tried the HTC VM6 Rom flash without CID unlock.
That was stupid. Very stupid, since I don't have the providers orginal ROM available.
My x7500 will not accept the HTC VM6 ROM and is stuck in Bootloader with "USB" at the bottom of the screen when connected to my PC. Hard reset does not start the normal "installation"
When I start the VM6 flash program I get the famous "provider error message"
Is there any possibility to unlock the CID in Bootloader or "flashing" the bootloader to use the original ROM image at my device for a re-install ? In that way I could use the X7500 unlocker in VM5 and then flash to VM6 after.
If not re-installing the original ROM or unlocking the CID is possible I guess my x7500 is seriously bricked.
I am sorry if the answer to my problem can be found in other treads here. I have searched and read a lot without any success. I know now that I should have unlocked the device before trying to flash -> can only blame my one stupidity.
I will be very happy for every advice.
Greetings, Eric
Click to expand...
Click to collapse
There were four ROMs posted here some time ago. At least one of them didn't require the unit to be SPL / CID unlocked. Try to get hold of one of those - look in the Athena WM6 forum (where this should have been posted)
ROM
apd said:
There were four ROMs posted here some time ago. At least one of them didn't require the unit to be SPL / CID unlocked. Try to get hold of one of those - look in the Athena WM6 forum (where this should have been posted)
Click to expand...
Click to collapse
Thanks for reply.
I suppose you mean this four Rom's :
http://uploaded.de/?id=j2pv51 - ROM ver 2.20
for use with the athena_upgrade program
http://uploaded.de/?id=0v9mm1 - flasher for SuperCID devices only
works only for supercid devices
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
http://uploaded.de/?id=wbbw2u - T-MOB005 - version with spl,ipl and etc
works with CID T-MOB005 and SuperCid
As I understand my x7500 is not unlocked/superCid'ed and I need a ROM with exactly the same CID as on my device. Or am I far out ?
Or should I be able to use one of them even if the CID don't match ?
Thanks, Erik
EricBr said:
Thanks for reply.
I suppose you mean this four Rom's :
http://uploaded.de/?id=j2pv51 - ROM ver 2.20
for use with the athena_upgrade program
http://uploaded.de/?id=0v9mm1 - flasher for SuperCID devices only
works only for supercid devices
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
http://uploaded.de/?id=wbbw2u - T-MOB005 - version with spl,ipl and etc
works with CID T-MOB005 and SuperCid
As I understand my x7500 is not unlocked/superCid'ed and I need a ROM with exactly the same CID as on my device. Or am I far out ?
Or should I be able to use one of them even if the CID don't match ?
Thanks, Erik
Click to expand...
Click to collapse
I think you need this one:
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
mackaby007 said:
I think you need this one:
http://uploaded.de/?id=430xr4 - HTC__001 - version with spl,ipl and etc
works with CID HTC__001 and SuperCid
Click to expand...
Click to collapse
Hi Mackaby, thanks for the answer.
That was the first ROM I tried to flash. Gave me error message "wrong vendor, check your update software"
Now I only get bootloader when I start my device. I have(had) a Norwegian ROM so I guess the CID does not match. I wish I unlocked my device before trying the WM6 ROM but......
Now I am stuck : Cannot boot / install my original ROM or install any.
My hope is that I can either unlock my CID in Bootloader or installing the original ROM again with a hard reset. To bad a hard reset only sends me to bootloader.
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
pof said:
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
Click to expand...
Click to collapse
Hey Pof,
Welcome to the Athena forum. Are you planning on being here or you were just passing by...
pof said:
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
Click to expand...
Click to collapse
Hi Pof ! Thanks for the answer and clarification. Will try today !
Greetings, Eric
pof said:
try this commands in mtty:
set 14 0
task 8
If it doesn't boot OS after this, you need a rom matching your CID. It's not possible to CID unlock it from bootloader.
Click to expand...
Click to collapse
Did it. Same result : Bootloader shows up after "task 8"
bootloader says :
athe100
ipl-v1.00
Athe100
SPL-v1.07.0000
red (raster)
green (raster)
blue (raster)
"Serial" when not USB connected, "USB" when connected in white field.
Guess I have to send my device for service since there are no ROM available for my local X7500 That's life
lpsi2000 said:
Are you planning on being here or you were just passing by...
Click to expand...
Click to collapse
Just passing by, sorry... i don't have athena
EricBr said:
Did it. Same result : Bootloader shows up after "task 8"
[...]
Guess I have to send my device for service since there are no ROM available for my local X7500 That's life
Click to expand...
Click to collapse
bummer..
Eric
As far as I know, all the athenas were provided withe the romcode ...if one hqs got the bonus pack.Just check withe someone for the bonus pack,,ai hope this helps.
hdubli said:
Eric
As far as I know, all the athenas were provided withe the romcode ...if one hqs got the bonus pack.Just check withe someone for the bonus pack,,ai hope this helps.
Click to expand...
Click to collapse
Hi Hdubli,
Thanks for the answer.
Bonus pack ? do you mean the CD that followed my x7500 ? I can check but don't think there are any ROM Flash application on that.
Sorry if I didn't understand your message correct
Greetings, Eric
If u buy bonus pack with athena which includes car kit etc etc, u also get CDs, in which the ROM is also there..so I was asking if u can get hold of the dealer from whom u hv got and enquire about it..also in mtty issue info 2 command check what is yr CID
hdubli said:
If u buy bonus pack with athena which includes car kit etc etc, u also get CDs, in which the ROM is also there..so I was asking if u can get hold of the dealer from whom u hv got and enquire about it..also in mtty issue info 2 command check what is yr CID
Click to expand...
Click to collapse
Ok, understand. We don't have anything called Bonuspack here with hardware stuff and ROM software.
This was the output from the mtty command :
Cmd>info 2
HTCSHTC__H10 ÅPýHTCE
Cmd>info 3
HTCSATHE100001.07.0000 ßؽôHTCE
Anything special with this ?
Anyone who knows if it is possible to mod a ROM flash file so that this CID will be accepted during install ?
EricBr said:
Anyone who knows if it is possible to mod a ROM flash file so that this CID will be accepted during install ?
Click to expand...
Click to collapse
That would corrupt the signatures, and it won't flash with an unmodified bootloader.
bootloader screen freeze after turning htc x7500 off
EricBr said:
Hi,
First many thanks to all people here at the forum who makes the day better and more interesting for mobile nerds like me. I have been lurking around here for a long time and enjoyed every minute of it.
My problem :
Since my x7500 is SIM unlocked and with a standard setup as far as I can see I tried the HTC VM6 Rom flash without CID unlock.
That was stupid. Very stupid, since I don't have the providers orginal ROM available.
My x7500 will not accept the HTC VM6 ROM and is stuck in Bootloader with "USB" at the bottom of the screen when connected to my PC. Hard reset does not start the normal "installation"
When I start the VM6 flash program I get the famous "provider error message"
Is there any possibility to unlock the CID in Bootloader or "flashing" the bootloader to use the original ROM image at my device for a re-install ? In that way I could use the X7500 unlocker in VM5 and then flash to VM6 after.
If not re-installing the original ROM or unlocking the CID is possible I guess my x7500 is seriously bricked.
I am sorry if the answer to my problem can be found in other treads here. I have searched and read a lot without any success. I know now that I should have unlocked the device before trying to flash -> can only blame my one stupidity.
I will be very happy for every advice.
Greetings, Eric
Click to expand...
Click to collapse
Thanks EricBr or anyone who can help me,
I have a similar problem, but in my case I didn't do anything to deserve it... I just turned off my new and provider unlocked x7500 after playing with it all day (just installed skype for mobile and customized some settings, tried the programs, etc.), and when I tried to turn it on again, it just froze in the bootloader screen... Nothing works, I tried soft and hard resets, don't know what else to do?
I've been reading al your posts everywhere and tried a few things without succes, when I conect my x7500 to my pc, it doesn't connect to activesync or anything. I guess I would do better if there would be someone who can create a reply that would clearly guide me on what to do and what files (with links) to download. I simply don't know what happened! since I didn't do anything especial to deserve this from my x7500 which I was falling in love with, after only a few hours of just getting to know it.
I'm new to xda's so please lay it down easy on me... Already had removed the sim and the miniSD I had installed on it... still nothing happens.
Hi everyone,my name's Larry and I just registered to the forums. Please forgive my newness but I am in a bit of a pickle here.
I have a MDA Vario II, aka Hermes 300, that I bought s/h off ebay. Works fine,no worries, but I upgraded to WM6 because i felt browsing was a little slow and the screen graphics werent as good as I expected. The upgrade was from the T-mobile site itself and all went fine. Only thing is I dont believe this phone can handle it(needs more RAM really) and after being online a while it gets really slow,like steerig a cow through treacle at times so I came to the conclusiong it was a bad move! Now I've noticed a link on here about downgrading to WM5 but is it that easy for one with no specialised tools or knowledge(tho i did build my own PC, or should I say ahem WE did)
Also a problem the phone has developed since the upgrade is it keep deleting my email settings, even tho on the 'desktop' screen it tells me i have so many unread emails in each account! So now i cant check emails from it either!
I do hope I can sort this out cos it is really frustrating having a PDA and not being able to browse properly!
Many thanks
Larry
Welcome to XDA-Developers larry. Well Firstly i would start with CID unlocking your device so that you can flash any rom you can do that by downloading hard spl from here
http://forum.xda-developers.com/showthread.php?t=296722
then once you have flashed that you can basically download and install any rom for the hermes. I have an mda vario ii and hate the t-mobile rom as it installs quite a bit of useless crap. I never use and it is also so damn ugly. if after installing a new rom you find you have internet connection problems and/or mms settings then download and run this http://rapidshare.com/files/92547562/UK_Setup.exe that will install the settings for internet and mms for all uk networks, the majority of the cooked roms on here though ,already have a network wizard to set it up for you, but better to be safe than sorry
P.S. I forgot to add if you are looking for speed and extra ram i would look for a vanilla(clean) rom, install that and then add the apps you want via cab files, you will find them scattered about all over this site
scousemartin said:
Welcome to XDA-Developers larry. Well Firstly i would start with CID unlocking your device so that you can flash any rom you can do that by downloading hard spl from here
http://forum.xda-developers.com/showthread.php?t=296722
then once you have flashed that you can basically download and install any rom for the hermes. I have an mda vario ii and hate the t-mobile rom as it installs quite a bit of useless crap. I never use and it is also so damn ugly. if after installing a new rom you find you have internet connection problems and/or mms settings then download and run this http://rapidshare.com/files/92547562/UK_Setup.exe that will install the settings for internet and mms for all uk networks, the majority of the cooked roms on here though ,already have a network wizard to set it up for you, but better to be safe than sorry
P.S. I forgot to add if you are looking for speed and extra ram i would look for a vanilla(clean) rom, install that and then add the apps you want via cab files, you will find them scattered about all over this site
Click to expand...
Click to collapse
Ah thanks for that but I have no idea what CID unlocking is(do you mean like unlocking the phone to other networks?) Also what's hard spl?? Totally in the dark about this!
Hermes300 said:
Ah thanks for that but I have no idea what CID unlocking is(do you mean like unlocking the phone to other networks?) Also what's hard spl?? Totally in the dark about this!
Click to expand...
Click to collapse
all your question answered here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
I have looked thru the wiki and cannot find the advice I need.
My device has the following on it and what I would like to know is if I can actually drowngrade the device back to WM5.
The rom version is 3.60.110.4 (T-mobile UK)
The radio version is 1.50.00.00 so I assume that it is boot 0108.
The IPL is 1.04 and the SPL 2.03.
The protocol reads as follows 32.83.7020.20H
I have come across a guide that states if the radio is above 1.27.00.00 then downgrading may not be possible.
"(NOTE: If your radio version is currently HIGHER than 1.27.00.00 then it is very likely the radio bootloader is version 0108, this WILL NOT allow the radio to be downgraded to a radio containing BL 0106 and will result in a "NO GSM" error.)" -http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=41&Itemid=27
The other question I would like to ask is this - it is possible to put another verion of WM6 on with this radio version?
Thanks for any advice!
Can anyone help me here!
Do I need to SIM unlock my PDA to update the ROM to a custom ROM, for example Schaps_WM6Pro_Hermes_4.30 which I recently downloaded from here.
At the moment it is locked to T-mobile. I have also updated the SPL to 2.10 olipro and the radio is at 1.50.00.00 and the HTC boot is 0108.
Thanks guys
Larry
Hermes300 said:
Can anyone help me here!
Do I need to SIM unlock my PDA to update the ROM to a custom ROM, for example Schaps_WM6Pro_Hermes_4.30 which I recently downloaded from here.
At the moment it is locked to T-mobile. I have also updated the SPL to 2.10 olipro and the radio is at 1.50.00.00 and the HTC boot is 0108.
Thanks guys
Larry
Click to expand...
Click to collapse
I think you might not have gotten help 'cause it doesn't look like you've read what people pointed for you to read. Hopefully this'll help you get over the jargon hump and make progress. Having upgraded from the Offical T-Moble rom and swapped ROMs, it's definitely worth taking the time to learn how to do.
SIM unlock & CID unlock aren't the same.
If you've had you phone with T-Mobile for at least 3 month they will let Unlock you SIM (at least they do in the US). Contact them directly, you'll need an active account & phone number with them. This is free.
CID unlocking allows flashing ROMs onto your PDA. For some reason the folks at T-mobile, etc want you to have to look at their stuff every time you use a machine you bought through them. Using a cooked rom is like reinstalling XP without having AOL on your computer, makes life much better.
(flashing = installing to a PDA's Read Only Memory)
(ROM = OS + Radio + other stuff = basically everything thats on the PDA after a hard reset)
Flashing can be a dangerous thing, you don't want to 'brick' your PDA so you install an escape hatch. Hard SPL is that escape hatch.
(Brick = peice of baked clay = your PDA if a ROM install fails and you didn't install Hard SPL first)
The Hard SPL protects you if the ROM you installs fails 'cause power went out, ROM was bad, you bumped the cable, etc
http://forum.xda-developers.com/showthread.php?t=296722
Read & Follow the directions.
Select a ROM from here
http://wiki.xda-developers.com/index.php?pagename=Hermes_Cooked_ROMs
I have the same model & just installed Custel V2.5, seems to work well so far (day 2).
http://forum.xda-developers.com/showthread.php?t=364617
Good Luck
Thanks gt, and we have read advice on here but a lot of seems to be conflicting plus we seem to be just going round and round. Yep, ben there, yep read that etc.
I know the diff. between SIM and CID unlock but all I want to know is is it necessary to SIM unlock the phone to update a ROM?
I wont be using another network but will be staying with T-mobile W n W.
I did it!
Well I did it. flashed the phone with Schaps WM6 4.30 WWE.
Have noticed it runs faster than the previous T-Mobile WM6 and has some really neat features-you can adjust a lot more settings on the phone than before,quite impresed! Thanks for everyones help!
Hi,
I purchased the Softbank X01HT (post Dec) in Japan when i was working in Japan. I lived with the Japanese OS even though i don't understand Japanese because I didn't want to temper with it just incase something goes wrong and i can't use the phone. Well, now im back in Australia ... and i need to unlock it and flash a new ROM to it so that I can use it in Australia .. otherwise.. it is effectively a brick....
so.. i spent the past two days reading all the valuable information u guys provided... and in the end.. i decided to first unlock and superCID my phone using the AUTO_Unlock_v3a.bat provided by POF ... and then flash it with the Jasjam telstra ROM (RUU_Hermes_DL_UK_3[1].62.305.5_6275_1.54.30.10_108_Ship.exe) also found in this forum which received good feedbacks...
ok... after i executed the AUTO_Unlock_v3a.bat program .. everything went well... and at the end of it.. the screen even said.. successful in both unlock and superCID ... so.. i assumed that my phone is unlocked...
then... i went to flash my phone with the abovementioned jasjam ROM .. and this too.. everything went just fine ... and now.. my phone is working with this new ROM (cool! first time im able to read my x01ht coz its in English) ...
without a sim.. the OS works fine.. etc etc...
however, when i tried to put a telstra sim card in it ... its still simlocked ...
the SimLock screen comes up and requests me to input unlock code ...
so.. i did more reading and researched but can't find any solution to this ... i even tried that "unlock" code (22051978) but it doesnt work ...
Please.. can someone help me with this issue with my phone? now.. it seems that i just need to unlock my phone to use it as my jasjam ROM is working fine. Below are further details:
ROM version: 3.62.305.5
ROM date: 11/06/07
Radio version: 1.54.30.10
EtRom version: 3.62.305.116
any help/comments will be highly appreciated... thanks in advance...!
read somewhere that if you let the softbank go through the 1st boot and it installs all the extra stuff you wont EVER be able to unlock it again. some one else may need to clarify this but apparently you need to soft reset after you've reached the today screen but before the customisations start. if you didnt do this then you probably wont be able to unlock it. sorry if this is wrong/bad news.
Hope someone else can corroborate this.. cheers...
thanks for your reply ultramag69 although i hope that u r wrong.. hahaha
fingers crossed ... hopefully.. positive news from some experts ...
After re-reading the posts, i cannot find that I did anything wrong.
This link "http://forum.xda-developers.com/showthread.php?t=293665" states that the unlocker v3a "can be used in all HTC Hermes devices, no matter which bootloader version the device is running", with the exception of "x01ht post April devices" (i.e., white x01ht).
However, my x01ht is black and is a pre-April device.
So, I am still not sure what is wrong. Please help please help any experts out there ...
POF ... if you are there.. please help ... i need your expert advice thank you in advance.
ultramag69, i think that you are referring to this "http://forum.xda-developers.com/showthread.php?t=301952".
Quote:
"Here's how to unlock the new batch of SoftBank X01HT devices with radio 1.14.01.10.
This process is ONLY valid for new devices which have never turned on or let the SoftBank Extended ROM install.
If you have already let the ExtROM install you CAN'T sim-unlock it."
Fortunately, i find that this does not apply to me because my phone is not post april. Also, originally, my radio was never 1.14.01.10. It was 1.14.00.10.
help..........
snowboarder said:
Hi,
I purchased the Softbank X01HT (post Dec) in Japan when i was working in Japan. I lived with the Japanese OS even though i don't understand Japanese because I didn't want to temper with it just incase something goes wrong and i can't use the phone. Well, now im back in Australia ... and i need to unlock it and flash a new ROM to it so that I can use it in Australia .. otherwise.. it is effectively a brick....
so.. i spent the past two days reading all the valuable information u guys provided... and in the end.. i decided to first unlock and superCID my phone using the AUTO_Unlock_v3a.bat provided by POF ... and then flash it with the Jasjam telstra ROM (RUU_Hermes_DL_UK_3[1].62.305.5_6275_1.54.30.10_108_Ship.exe) also found in this forum which received good feedbacks...
ok... after i executed the AUTO_Unlock_v3a.bat program .. everything went well... and at the end of it.. the screen even said.. successful in both unlock and superCID ... so.. i assumed that my phone is unlocked...
then... i went to flash my phone with the abovementioned jasjam ROM .. and this too.. everything went just fine ... and now.. my phone is working with this new ROM (cool! first time im able to read my x01ht coz its in English) ...
without a sim.. the OS works fine.. etc etc...
however, when i tried to put a telstra sim card in it ... its still simlocked ...
the SimLock screen comes up and requests me to input unlock code ...
so.. i did more reading and researched but can't find any solution to this ... i even tried that "unlock" code (22051978) but it doesnt work ...
Please.. can someone help me with this issue with my phone? now.. it seems that i just need to unlock my phone to use it as my jasjam ROM is working fine. Below are further details:
ROM version: 3.62.305.5
ROM date: 11/06/07
Radio version: 1.54.30.10
EtRom version: 3.62.305.116
any help/comments will be highly appreciated... thanks in advance...!
Click to expand...
Click to collapse
hey bro!when you r already flashed v3a unlock,than you should down a software name like "Hard-SPL-V7",it will help you to unlock the exrom,make you able to flash the new os\rom...
"HARD-SPL-V7" has 2 software,1st is "RUU_signed.nbh",2nd is "RUUWrapper.exe".
devileric, read post carefully. snowboarder has no problem with reflashing oses, its the sim that needs unlocking now and hard spl WONT do that...
Still reading and researching. I'd probably retry the unlock tool. it cant hurt but may work... cheers
devileric ... yes ... ultramag69 is correct ... my new English Telstra Jasjam OS works like a beauty when it operates WITHOUT a sim card. However, when i try to insert a telstra (or optus) sim card in there, there is a prompt that requires me to enter a unlock code. Please note that the unlock code 22051978 does NOT work in this case (also doesnt work in alot of other cases that i read in this forum).
Ultramag69, thank you for your help and replies, much appreciated. I actually did try the unlocking program again (three times ) . However, when i execute the AUTO_Unlock_v3a.bat when my OS is the new telstra jasjam OS, my phone will freeze on the telstra startup screen after the radio update step of the unlocking program when it automatically resets. Thereafter, even when i perform soft reset again and again, it will just freeze there. When that happened the first time, I thought that I bricked my phone .. ahhaha.. but fortunately, I was able to simply go to the tri-color boot screen and then simply flash the above said telstra Jasjam ROM. This will get me back to square one, i.e., working Jasjam OS, but phone is still sim locked.
I spent another night last night reading the applicable threads. I find that quite afew other people had the same problem as me. And I also find that whenever such problem is posted, its either ignored or a moot reply is given.
So, for the experts out there, if there is a solution to this, please kindly let me know. I am sure it will others will find it helpful too. Thank you.
Sorry wrong post