Related
Dear All master,
I need help on my o2 Atom, when I upgrade it to latest version, it stop on stage 5: Burn in Radio Rom, 0%. Nothing happen even I had to wait for 1 hour.
I upgrade it with original atom rom from o2 site : 'Xda-Atom-ENG-20060426-MOT0822.exe'
The device stay in "O2" screen. this device can switch to diagnostic mode.
what should I do?
Note I repeated loading rom but Ietunai problem in Flash
Probably the Radio Hardware broken.... try to install without the Radio ROM.
sliders7 said:
Probably the Radio Hardware broken.... try to install without the Radio ROM.
Click to expand...
Click to collapse
from wher i can find that rom ?
or can u upload it ? for me plzzzz
http://pdaviet.net/showthread.php?t=17158
you can find how to flash rom without bootloader, extended rom , radio.
read my first post
medkid said:
http://pdaviet.net/showthread.php?t=17158
you can find how to flash rom without bootloader, extended rom , radio.
read my first post
Click to expand...
Click to collapse
but my phone is dead and it fail when i try to unpgrade it and it gave this eorr ===
!!!Please use DSUU in OS mode and syno with PC first !!!
usb transfer fail.
what shoud i do now plzz help me i dont know how to get it in DSUU mode its gose on boot loader but cant get it in to DUSS MODE
my Xda Atom Exec o2
waseemraj said:
but my phone is dead and it fail when i try to unpgrade it and it gave this eorr ===
!!!Please use DSUU in OS mode and syno with PC first !!!
usb transfer fail.
what shoud i do now plzz help me i dont know how to get it in DSUU mode its gose on boot loader but cant get it in to DUSS MODE
my Xda Atom Exec o2
Click to expand...
Click to collapse
u can't update using DSUU from activesync anymore. since u got broken ROM.
u must use Bootloader by pressing:
-power + camera + reset
-plug the USB
-start the update using DSUU.
sliders7 said:
u can't update using DSUU from activesync anymore. since u got broken ROM.
u must use Bootloader by pressing:
-power + camera + reset
-plug the USB
-start the update using DSUU.
Click to expand...
Click to collapse
i just do as u say but the but it fail gives the eorr as i told in my last post
and plzz tell me is i just have to get it in bootmode and conact it with usb and start updating
what is DSUU?? is this the file Xda-Atom-Exec-ENG-20060721-MOT0822 ? or what ?
Easy fix, check post #12 http://forum.xda-developers.com/showthread.php?t=319945&page=2&highlight=EBOOT
more than likely you will need a 256 or 512MB SD Card, the method discussed here (in most cases) will not work with higher capacity cards. Check the Atom Wiki too.
homer285 said:
Easy fix, check post #12 http://forum.xda-developers.com/showthread.php?t=319945&page=2&highlight=EBOOT
more than likely you will need a 256 or 512MB SD Card, the method discussed here (in most cases) will not work with higher capacity cards. Check the Atom Wiki too.
Click to expand...
Click to collapse
i tryied that too but still same postion.....
what shoud i do now plzzz help me i tell u again what it look like
====================================================
USB connected,waiting for download ..............
!!!Please use DSUU in OS mode and syc with PC first!!!
Usb Transfer fail
some one plzzzz help me ? for my atom exec
waseemraj said:
some one plzzzz help me ? for my atom exec
Click to expand...
Click to collapse
well...
after u see bootloader screen and waiting to download.
it should be ok to connect to USB and PC will recognize it for sure!
if doesn't... u should try different computer. not yours. just borrow somebody else computer... see the outcomes? just in case u got error/corrupted activesync.
if still not working... u must using SD card upgrade.
Use any ROM.. use WM5 Official ROM.
Extract the ROM.
put: diskimage_Ver.nb0 to the Blank SD card (use 512MB or 1GB)
and activate the bootloader again.
If your device are normal.. it should looking for SD card and start installing the ROM. If your device badly damage.. it will NOT run both method.
i don't know this is your hardware or Software are damage.
Maybe u should send it to the repair... hopefully u still got the warranty.
If Hardware is the problem, usually they replace the motherboard.
because no way to fix NAND memory module.
just keep trying... don't try one time only...
Good Luck & Pray!
sliders7 said:
well...
after u see bootloader screen and waiting to download.
it should be ok to connect to USB and PC will recognize it for sure!
if doesn't... u should try different computer. not yours. just borrow somebody else computer... see the outcomes? just in case u got error/corrupted activesync.
if still not working... u must using SD card upgrade.
Use any ROM.. use WM5 Official ROM.
Extract the ROM.
put: diskimage_Ver.nb0 to the Blank SD card (use 512MB or 1GB)
and activate the bootloader again.
If your device are normal.. it should looking for SD card and start installing the ROM. If your device badly damage.. it will NOT run both method.
i don't know this is your hardware or Software are damage.
Maybe u should send it to the repair... hopefully u still got the warranty.
If Hardware is the problem, usually they replace the motherboard.
because no way to fix NAND memory module.
just keep trying... don't try one time only...
Good Luck & Pray!
Click to expand...
Click to collapse
The above information will likely do more harm than good!
waseemraj said:
i tryied that too but still same postion.....
what shoud i do now plzzz help me i tell u again what it look like
====================================================
USB connected,waiting for download ..............
!!!Please use DSUU in OS mode and syc with PC first!!!
Usb Transfer fail
Click to expand...
Click to collapse
Bro I have recovered from this 20+ times, if its not working (and you can enter bootloader mode) then you're doing something incorrectly, either that or your memcard is incompatible, remember in most cases 256 or 512MB are the only working sizes! So place that EBOOT.nbo into and "empty" SDCard with your PC, enter the bootloader then stick the card in.... It wont take long, once you the screen goes black pull out the SDcard and then enter bootloader, plugin your USB and execute official O2 rom AKU2.2
The flash may not finish completely freezing in the Extended rom update, dont panic! unplug, softreset then flash in DSUU mode...easy as! works every time!
homer285 said:
Bro I have recovered from this 20+ times, if its not working (and you can enter bootloader mode) then you're doing something incorrectly, either that or your memcard is incompatible, remember in most cases 256 or 512MB are the only working sizes! So place that EBOOT.nbo into and "empty" SDCard with your PC, enter the bootloader then stick the card in.... It wont take long, once you the screen goes black pull out the SDcard and then enter bootloader, plugin your USB and execute official O2 rom AKU2.2
The flash may not finish completely freezing in the Extended rom update, dont panic! unplug, softreset then flash in DSUU mode...easy as! works every time!
Click to expand...
Click to collapse
Confirm!!!
I have done this also even using 1 GB memcard, my memcard is NCP mini SD.
I don't know it was lucky or it does work for 1 GB memcard. Even with non empty one.
But becareful, maybe I am just lucky, perhaps you should use 256 MB or 512 MB only.
homer285 said:
The above information will likely do more harm than good!
Click to expand...
Click to collapse
hei... he is desperately need help.
We all want to help him, thats all i can offer.
If you have different method.. thats a good news for him.
everybody here try to help him.. contribute something to help him.
so no more harm to his already broken device.
think the brighter side!
cheers
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
p.s srry for my bad english
Did you rename it to eboot.nbo ? Have any files in root folder of your miniSD ?
Who make you try this way ???
i rename as i mentioned above with the long name only change the .nbf to .nb0
i also regret now coz cant even see anything from the screen >> althought tried reset eith all the mothod..
izzit my 6828 dead ad?
cant even repair by myself and have to send it back to hp for repair?
williamSun said:
i rename as i mentioned above with the long name only change the .nbf to .nb0
i also regret now coz cant even see anything from the screen >> althought tried reset eith all the mothod..
izzit my 6828 dead ad?
cant even repair by myself and have to send it back to hp for repair?
Click to expand...
Click to collapse
If you don't rename to eboot.nb0 => Your device didn't flash it => Your device not dead. Have another files in the root folder of miniSD card ? List for me!!!
--Try this way :
Press both softkeys (two "-" keys) and remove battery then insert battery again (don't unpress two softkeys) and softreset, wait 2-3 seconds. It'll go bootloader mode. You can flash your device again.
hmm, tried u way ad didt make it to boot screen..>.<
in case i rename to eboot.nb0 >>i not really sure<<
>>izzit case sencetive?
>>izzit 6828 dead??
williamSun said:
hmm, tried u way ad didt make it to boot screen..>.<
in case i rename to eboot.nb0 >>i not really sure<<
>>izzit case sencetive?
>>izzit 6828 dead??
Click to expand...
Click to collapse
What is your current bootloader, 1.01 or 1.05 ?
If you follow that menthod but it didn't go to bootloader, your bootloader was dead.
You can send it to HP to repair, or try this way : http://wiki.xda-developers.com/index.php?pagename=DeadBoot
I recommend to sent it to HP.
while the PDA is still can open and bootloader screen
is 1.01
and im trying to use the EBOOT0502_MNT_01.01.03.nbf which found in the
HP official RUU PC flash ROM
and rename to EBOOT0502_MNT_01.01.03.nb0
then put in the root of memory card
then start to flash ..
now the PDA wouldn't reapond to any button HR, SR, soft-key + reset ...etc
only can charge and orange LED indicated
williamSun said:
while the PDA is still can open and bootloader screen
is 1.01
and im trying to use the EBOOT0502_MNT_01.01.03.nbf which found in the
HP official RUU PC flash ROM
and rename to EBOOT0502_MNT_01.01.03.nb0
then put in the root of memory card
then start to flash ..
now the PDA wouldn't reapond to any button HR, SR, soft-key + reset ...etc
only can charge and orange LED indicated
Click to expand...
Click to collapse
You was flash wrong bootloader due to make your device dead.
Now you need restore bootloader.
If you send to HP, they will replace board you must pay for it.
But you try the JTAG menthod to restore bootloader it'll make your warranty expired.
thx for all ur answer, i really appreeciated.
btw, for sure hp center will replace a board in it and that will be expensive rite?
if i sent to other shop which is not HP official service, will they do the same?
izzit juz flash using tools they hv>?
and expensive?
Here is what I did ... might help you
Hi
Make sure your phone is powered, it would be wise to charge the phone via AC power at least for 1-2 hours before you try to install anything.
I finally managed to install WM6 on my HP ipaq rw6828. But it wasnt easy, it took me 1 full day to get it installed. Just to help other people who are installing this, here is my experience -
What all I did and how I finally got there -
1.
Tried to install it via PC. When I already had a higher version of the Bootloader installed. Best way is to install it via 1GB mini SD card.
2.
After reading other posts I managed to downgrade the bootloader to version 1.0.1 (not sure of the version number...but its the version you get after installing the HP SP34074).
3.
Once I managed to downgrade. I got into the Bootloader mode on my device( its pretty simple to get into BL mode, make sure you ask someone to help you with it, its easier with two people, to get into Bootloader mode - a)press the two "-" buttons on the phone together. b)While the two "-" are pressed have a second person remove the battery. c) Wait for a few seconds and ask the person to insert the battery back. d)Once the battery is in place ask the second person to use the stylus and push into the soft reset hole (its hole on the left of the USB connecter on the phone). e) Wait for a few seconds and then phone should go into the BL mode. f) release the two "-" buttons after it enters the BL mode. Sometimes for me it entered the BL mode after I released the "-" buttons also. But dont release the "-" buttons till you have pressed into the hole with the stylus.
4.
With my phone now in the BL mode and showing the older version 1.0.1 (not sure but it should not be 1.0.5) I clicked the Device Software Update Utility.exe. I got the screen where you get a combo/dropdown with "ALL" pre-selected. The install step clearly says choose "OS" only and not "ALL". But I made a mistake here, for some reason using the mouse I didnt see any other option in the dropdown accept for "ALL". so I selected ALL and did a next. The setup kicked in and I got different screens showing status of install. But on the final screen it got stuck at 6% and stayed like that for well over 6 hours...I didnt touch the install as the instruction clearly say not to disconnect or stop the exe. But after 6 hours I realized that something is wrong and i killed the Device Software Update Utility.exe file.
5.
I did a soft reset on the phone and to my surprise after a while it loaded WM6....but that was it. Has the install failed in between the WM6 on the phone was totally screwed up...nothing worked properly. I coudnt even get ActiveSync to recogonise my device or connect to it.
6.
I tried the whole sequence mentioned in step 4 again but no luck now Device Software Update Utility.exe would error out I assume it could be because of the BL version 1.0.5. So I thought let downgrade and install the older BL version....but with no active sync i coudnt downgrade the device.
7.
Then i read somewhere SD card boot method to copy the EBOOT0908_MNT_1.00.05.nbf from the SP34074 and rename to eboot.nbo. This didnt work either, am not sure if I renamed the file correctly to .nbo(Orange) or .nb0(zero). Well I dont know whats correct eboot.nbo or eboot.nb0. But since this step didnt work. I was really upset as I felt I was stuck...then GOD had mercy on me and I did something which simply worked ...
8.
I took my mini SD card out connected to my Laptop in the SD card slot with the SD adapter. Did a quickformat to clean it up...if you have data its a good idea to back up the SD card in a seperate folder.
9.
Now I had a clean SD card with no files I downloaded the 1.0.5a (for 68x8) for miniSD. I copied the diskimg.nb0, size : 64,000 KB to the SD card root folder.
10.
Since I was trying the SD card method, I connected the mobile to AC power instead of the PC just to make sure I had enough power for install.
11.
I popped the SD card back into the phone. Removed the phone battery. Then entered into the Bootloader mode (refer to step 3 for getting into BL mode). Well nothing seemed to be happening...but I decided to stay on the BL mode .... to my surprise after 10-15 min i got a message asking my reset and goto factory mode. I wasnt sure if it was asking me to do something or was just a message. While I was wondering...the phone restarted automatically and it loaded WM6 ..asked me to do the tap thing to configure like the initial factory setup .. after all this I poped my SIM inside. Connected the phone to my PC. Active Sync finally recognized my device and synched everthing. Now everything WORKS!!! Though there are some issues like the camera flash doesnt come on.. etc but more or less everything seems to work. I havent tried other applications like email SMS wifi bluetooth etc.. I will post soon my experience weather all main applications work without a glitch...but am so happy my patience paid off..
Thanks to nhocbanme for WM6 version for HP ipqa rw6828, my biggest mistake was not to properly follow steps listed by nhocbanme. For people trying to install WM6 on HP ipaq rw6828....please please use the SD card method...it works and takes less then 30 minutes...you can follow my steps 8,9,10,11 to have a trouble free setup.
Good luck
Amit Reddy
Hi... my bootloader is dead any I cannot locate the fin out to flash my ipaq rw6828... please tell me where exactly are the pin out for rw6828
Thanks you.
Hi WilliamSun,
if you can go to boot loader it mean you can repair your device. You should download WM5/WM6/WM6.1 ROM that design to flash via mini SD. you can download it from nhocbanme's or hellowordl1's thread, and flash your device again.
Good Luck.
HELP
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
in this case i cant solve my problem
downgrade with SP34074 from PC (like intruction on screen PC)
1. run SP34074 from PC
2. remove battrey from device for sec, and put back to device
3. connect the device via USB, n make sure the PC is respon that
4. follow the instruction in screen
its work for me
ITS A HTC HD2 NOT THE ORIGINAL
Ok I am a really big noob and need some help. I Flashed My rom using Miri_HD2_WM65_21893_Sense25_V6.0.rar, I extracted in and it completed 100% and loaded up perfectly to home screen. I didnt have my sim card in or Sd card so I took battery out and put my sim card and sd card back in. When I turned it back on it was stuck on the HTC screen. Just the Green HTC writing and white screen and thats it. I have read some forums that have had the same problem but i just dont get it. they say get into bootloader ( which i can do) and then flash with radio or something... I am uncertain how to do this. When I downloaded one of them Customruu or whatever it is and open it it says I have to connect through active sync which i cant do because I cant get my device to turn On... I really need some help but it needs to be explain to me like explaining to a handicap person.
thanks
Put into bootloader, not necessary to connect to Activesync as you can't in bootloader mode. Flash the radio the same way as you flashed the rom. put the radio.nbh file in a folder, rename it to RUU_Signed.nbh and copy a CustomRUU.exe in and flash.
You'll find radios and steps here.
jaza20032000 said:
Ok I am a really big noob and need some help. I Flashed My rom using Miri_HD2_WM65_21893_Sense25_V6.0.rar, I extracted in and it completed 100% and loaded up perfectly to home screen. I didnt have my sim card in or Sd card so I took battery out and put my sim card and sd card back in. When I turned it back on it was stuck on the HTC screen. Just the Green HTC writing and white screen and thats it. I have read some forums that have had the same problem but i just dont get it. they say get into bootloader ( which i can do) and then flash with radio or something... I am uncertain how to do this. When I downloaded one of them Customruu or whatever it is and open it it says I have to connect through active sync which i cant do because I cant get my device to turn On... I really need some help but it needs to be explain to me like explaining to a handicap person.
thanks
Click to expand...
Click to collapse
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
where do I get the Customruu.exe from? What do you mean flash the radio same as the rom? how can i do that if i cant get connect to active sync? So does that mean I have to download Miri_HD2_WM65_21893_Sense25_V6.0.rar again? which radio file do I choose? I am so confused. Dont get annoyed its just i dont understand all this...
do NOT do it via SD card - flash the radio using activesync as mentioned in first reply. SD card is dodgy as hell and the quickest way to brick your phone for good
You can get CustomRRU from any ROM file - use the one from Miri's ROM
might've been worth reading the n00b flashing thread first as well as well as the first thread of Miri's ROM as all the info is on there...
how come you can't use activesync? what version of Windows you using?
in future i suggest you read the relevent threads and make sure you can flash a stock ROM before jumping into cooked ROMs...don't wanna brick an expensive phone do you?!?!
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
I can't use the SD card because I dont have the adapter thing to be able to hook it up to my comp only way i could access it was through my phone in hard drive mode. So basically i cant put any files on it without using the phone... Any other suggestions?
futher info from Miri's ROM thread...
"You MUST use radio 2.07.50.27 or 2.08.50.08"
read this thread...
http://forum.xda-developers.com/showthread.php?t=609477
all will become clear - or it should do!!
EddyOS said:
do NOT do it via SD card - flash the radio using activesync as mentioned in first reply. SD card is dodgy as hell and the quickest way to brick your phone for good
You can get CustomRRU from any ROM file - use the one from Miri's ROM
might've been worth reading the n00b flashing thread first as well as well as the first thread of Miri's ROM as all the info is on there...
how come you can't use activesync? what version of Windows you using?
in future i suggest you read the relevent threads and make sure you can flash a stock ROM before jumping into cooked ROMs...don't wanna brick an expensive phone do you?!?!
Click to expand...
Click to collapse
If you read my post I cannot get into the home screen... My Phone is stuck on the HTC boot up screen therefore making it impossible to use activesync... I did read all the Noob and Miri **** and it worked. I got to the new rom, but when i took the battery out and put sim card and sd card back in it is just stuck on the green htc screen and wont go past it...?????????
jaza20032000 said:
I can't use the SD card because I dont have the adapter thing to be able to hook it up to my comp only way i could access it was through my phone in hard drive mode. So basically i cant put any files on it without using the phone... Any other suggestions?
Click to expand...
Click to collapse
i would say buy one only cost about £5 to £10 uk pound
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: http://forum.xda-developers.com/showthread.php?t=575524) with the radio file from this link:
http://megaupload.com/?d=HT7ZMDGH
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
EddyOS said:
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: ) with the radio file from this link:
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
Click to expand...
Click to collapse
Where do I get jus the CustomRRU.exe..?? For miri?
Edit: Just read post again you included link in last quote, yes i know i am retard
I put a link for it in brackets (found here: ) - use your eyes!! lol
if you're not prepared to read what people put then don't ask for help
EddyOS said:
It just sounds like you've got the wrong radio on your device...
Turn off your phone, and turn it back on holding down just the down button. It will go into the bootloader screen (red green and blue one). You can then connect it to your PC and it should say 'USB' at the bottom instead of serial.
You can then run CustomRRU (found here: http://forum.xda-developers.com/showthread.php?t=575524) with the radio file from this link:
http://megaupload.com/?d=HT7ZMDGH
and it should allow you to flash the radio and work...(put both the CustomRRU app and radio file in the same folder)
Click to expand...
Click to collapse
I am using a HTC LEO (HD2) with EnergyROM installed in it. Now I was tryin to flash updated version (11th march update), But I am having trouble with Activesync which somehows is from last few weeks. It connects & syncs the device too once USB is plugged in, But disconnects when I try to flash a rom using customRUU..It gets disconnected on the bootloader screen & activesync status turns to Disconnected from Connected..I pull out my battery & restart the device again. This is highly irritating & I wish if there's some other program instead of Activesync that could be used to flash a rom.
I tried doing it with bootloader screen, Turning the device off, then turning it on while pressing down the volume button, It sure goes into bootloader screen, but shows Serial at the bottom & not USB..So any ideas for what could be the alternative for people who face the same problem with activesync, Instead of wasting time to rectify this error, Its better to find some other alternative. My PC is running Windows XP 32 bit, I re-installed my windows when i had trouble almost a month back & activesync worked fine then, But just can't afford to do it every other week or so
????
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
when i do this hd2 says NOT ALLOW What should i do??
sbugra said:
when i do this hd2 says NOT ALLOW What should i do??
Click to expand...
Click to collapse
Flash via pc
ClydeB1 said:
Flash via pc
Click to expand...
Click to collapse
done it. thnx
vicky_crispy said:
I am using a HTC LEO (HD2) with EnergyROM installed in it. Now I was tryin to flash updated version (11th march update), But I am having trouble with Activesync which somehows is from last few weeks. It connects & syncs the device too once USB is plugged in, But disconnects when I try to flash a rom using customRUU..It gets disconnected on the bootloader screen & activesync status turns to Disconnected from Connected..I pull out my battery & restart the device again. This is highly irritating & I wish if there's some other program instead of Activesync that could be used to flash a rom.
I tried doing it with bootloader screen, Turning the device off, then turning it on while pressing down the volume button, It sure goes into bootloader screen, but shows Serial at the bottom & not USB..So any ideas for what could be the alternative for people who face the same problem with activesync, Instead of wasting time to rectify this error, Its better to find some other alternative. My PC is running Windows XP 32 bit, I re-installed my windows when i had trouble almost a month back & activesync worked fine then, But just can't afford to do it every other week or so
Click to expand...
Click to collapse
It's not possible to connect to Activesync while being in the bootloader mode (The hd2 says "USB" on Windows without activesync too), so it has nothing to do with Active sync. Try another USB-Cable or use the sdcard to flash (see amma2005's Post, but as far as I know, there is no need to format the card again).
amma2005 said:
hi had same thing myself just rename ruu_sined.nbh to leoing.nbh
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
Great advice mate.
Been a rom junkie for weeks, bouncing around several releases to find the one.
turned towards Dutty, flashed and got a wihte screen for my trouble. Followed your advice and now running CDLC V2 "dutty" without a hiccup.
eng.mohammad said:
Dear Friend;
i faced the same problem and thanks my ALLAHH, i found that the connector copper pin that connect the battery with the phone is not in its right direction so i used my hand to redirect it to can connect with the battery
Click to expand...
Click to collapse
Hi. Can you help with this? or anyone?
leo70 said:
Hi. New here. Done this magldr 1.12 and leo70 rom but my phone playing up badly after a lot of droid and 6 and other flashes. I can't install hardly any rom any more without it - ie: stock, wm6, android, wp7 rebooting constantly for no reason etc.
Done mtty and have bad blocks - about 16 and 16 reversed. done task 28 and task 28 55aa, and task 29 as read in other threads. tried everything with different radios, different nand droid. multiple wp7-hd2 installs. but still reboots.
Any thoughts? If go back to stock+spl1.66 and send back under warranty anyone know/think if they will fix it and/or replace it? they still have old sealed replacement hd2 stock or boards much? do they do diagnostics and look at bad blocks properly on warranty return? Even on stock-rom and stock-spl still does this reboot although not as much. Worried that stock-rom wm6 will "work" too well and they won't check blocks. What about task2a? etc? Any way to install wp7/magldr and partition right so no bad blocks counted in?
Thanks very much.
Will pay for fix that works - $.
Click to expand...
Click to collapse
I am stuck on DFT boot screen after hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage.
and yes, was Windows Phone 7 and activated with marketplace & xbox/live.
leo70 said:
Hi. Can you help with this? or anyone?
I am stuck on DFT boot screen after hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage.
and yes, was Windows Phone 7 and activated with marketplace & xbox/live.
Click to expand...
Click to collapse
Did you check the battery pins ? Sometimes they do get bent out of alignment and simply pushing them back into place gently does the trick.
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
gjizaqin said:
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
Click to expand...
Click to collapse
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
CaponiND said:
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
Click to expand...
Click to collapse
Actually the sd is original 2gb that comes with hd2.
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
mladen.p said:
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
Click to expand...
Click to collapse
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
gjizaqin said:
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
Click to expand...
Click to collapse
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
zengxisheng said:
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
Click to expand...
Click to collapse
Ok I installed 2.08.HSPL from 1.42.HSPL and it went successfully, now i see 2.08.HSPL on bootloader but it still fails to update ROM. Stops at 8 % on the phone with rectangle mark, and on the pc it stops at 9 %.
I get Error 290 - Unknown Command
But why i cant go into sd card flash screen when i press reset and volume down ?
I just used another 2 gb microSD and added LEOIMG.nbh from official FRE ROM and it doesnt work.
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
ce3c said:
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
Click to expand...
Click to collapse
Hmmm this kinda messed me up.
What EXE file you run on the pc so it triggered update from SD ?
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
So i would say maby you just got it somehow with key kombination, because it would be impossible to run it the way you say. Or maby i'm wrong.
Could you be more specific about how you exactly run that process?
Thanks for your kind help. Gjizaqin
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
Click to expand...
Click to collapse
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
ce3c said:
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
Click to expand...
Click to collapse
Whell, by doing this procedure your doing normal ROM Update, and it's not doing update from sd card.
Anyways i tried this way too but not successful, its stuck on 8 % and stay's that way for about 3 minutes, than it gives me error 362 on the loader.
Anyways thanks for your help mate.
Anyone with experience can give me advice what to do with this phone?
Thanks in advance.
Gjizaqin
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
whizzkid_cool said:
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
Click to expand...
Click to collapse
I guess were on the same boat
gjizaqin said:
I guess were on the same boat
Click to expand...
Click to collapse
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
jordy1990 said:
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
Click to expand...
Click to collapse
There has been reported problems with some 16GBmSD cards when it comes to flashing from them.
The only thing you need on the mSD card is the LEOIMG.nbh file.
dwntoearth said:
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
Click to expand...
Click to collapse
If you boot up your phone to Bootloader mode (but not connected to the computer), the bottom of the screen reads 'Serial'. If you now plug it into the computer, does it change to 'USB'?
Your computer error message is just saying that the computer cannot install a driver to communicate properly with your phone. Since your phone isn't fully loaded into WinMo then your computer isn't going to recognise it as a WinMo device. So don't worry about that message.
feridoun said:
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Click to expand...
Click to collapse
I guess this problem happen to some of the flash addicts! Problem still unsolved...
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
Hi i was new to all this and installed dynamics v2.0 fully unlocked rom the other day and this is how i went about it
download this
RUU_Mozart_Orange_UK_1.24.061.35_Radio_5.50.09.18_22.24.50.09U
http://www8.zippyshare.com/v/48117282/file.html
this is a load your phone back to 1.24
to install it i did this
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial but maybe it will need to install some drivers cant remember 100%
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that then you will have your phone back to 1.24
next you can follow this post here and download the attachment at the bottom named DFT_XSPL_WP7FG1.rar this what u need for this step
http://forum.xda-developers.com/showthread.php?t=1195647
basically this is the install procedure u may need to install active sync (XP) or windows mobile device center (vista and 7) but i did not have to my phone automatically did this
DFT_RSPL_WP7FG1_LAUNCH allows you to load RSPL on the device:
1. Extract ALL files from RAR archive.
2. Run DFT_RSPL_WP7FG1_LAUNCH (with administrative rights to access USB)
3. Mindfully reads information text. Press “Next” button.
4. Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
5. Connect your device to PC via USB cable.
6. Now you may need to install proper USB drivers. They come with Active Sync / Windows Mobile Device Center.
7. Install drivers if required.
8. Make sure device show “USB” at the bottom instead of “Serial”.
9. Press “Next” button in the wizard. It should detect your phone.
10. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
11. After successful connection it should show device codename and allows to choose installed OSPL version.
12. You should look at the screen and select OSPL version in drop down list box. You need do this because it’s not possible to detect installed version via USB.
If your current SPL version doesn't present in the list, you can choose nearest version,
BUT ONLY IF IT HAS SAME FIRST NUMBER!!
Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.
13. Press “Next”. Wait until comes final page.
14. Read and close window
15. Look at the device – it must reboot to RSPL.
16. If you see RSPLX.Y.Z and “CotullaRSPL” on the screen – the task done! Otherwise, please report in this thread about your problems.
17. Put some feedback in this thread for community and developers.
Installing HSPL
DFT_HSPL_WP7FG1_INSTALL allows you to install HSPL on the device:
1. Launch RSPL on the device like described above.
2. Be sure that you close RSPL wizard window.
3. Run DFT_HSPL_WP7FG1_INSTALL.exe (with administrative rights to access USB)
4. Mindfully reads information text. Press “Next” button.
5. Proper drivers already must be installed in RSPL step.
6. Press “Next” button in the wizard. It should detect your phone.
7. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
8. After successful connection it should show device codename and allows to choose HSPL or OSPL version to install. OSPL means you install stock SPL back.
9. Check device codename, if something wrong turn off computer and run to the nearest forest. Grab some water with yourself.
10. Press “Next”. Wait until comes final page.
11. Device will reboot and start to boot OS.
12. Reset it and enter SPL mode again. Be sure there HSPLX.Y.Z and “CotullaHSPL” appear.
13. Put some feedback in this thread for community and developers.
Now u are ready
you can find what custom rom you want i used dynamics v2.0 which can be found here and its fully unlocked aswell so all i all im pleased with it
http://forum.xda-developers.com/showthread.php?t=1520352
download it and install the same way we installed the 1.24 rom in the begining of this post
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that and then you will have loaded your desired custom rom onto your phone
I hope this helps some of u out and happy modding
best regards
steve
1.24
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
geofferz said:
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
Click to expand...
Click to collapse
1.24 im refering to the SPL you can find your version by turning the phone off holding volume down and power button and u will see your SPL at the top,
im not sure about the unlocked sim/network im new to all this aswell maybe do a search on the forums and see if you can find the answer, but i dont know this 1 sorry :/
rom is good no issues had a cable issue yesterday that wouldnt let me charge my phone but thats down to my dodgy cable
you dont have to install this rom you can use any custom rom you like or might find out there
anyways hope this helps
Launch RSPL
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
geofferz said:
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
Click to expand...
Click to collapse
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Oh also do not extract the 1.24 from the .rar file run everything from there
This is why ur getting that error I think
geofferz said:
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
Click to expand...
Click to collapse
you dont need to select a option just load ROMUpdateUtility.exe
ive just downlaoded and reinstalled the rom myself to try see what u mean and i dont get this option
when you go to bootloader screen on your phone and it says usb open the rom file and click ROMUpdateUtility.exe
now dont open active sync or mobile tools as it says on the program information
just click the tick boxes and continue through the process
maybe try download the rom again found this
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
but like i sed i have downloaded the file myself and it is working for me without any problems
beany2009 said:
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Click to expand...
Click to collapse
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
geofferz said:
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
Click to expand...
Click to collapse
lol np mate ill try help as best i can
right i understand your bit now about the dynamics rom u need to select regular on this part
custom i think would be if u want to edit it or some **** but i have no idea so u use regular mate because this is the actual rom file made but remember u must downgrade and load rspl and hspl onto your phone before doing this step
right my firmware is 2250.21.51301.401 but i dont know if this changes on installation of the downgrade and adding the custom rom like i sed im a complete noob with this myself but all went smoothly for me thats why i made the tutorial
and no mate my phone took about 5-10 mins to install the 1.24 orange rom
have u tried a hard reset first and then see if it helps with the installation
ill search around for your firmware and see if there has been issues
edit..........................................
did a search on the forums and your firmware comes up with nothing :/ did a google and only shows this thread did you type the numbers correctly?
also you mean that the rom update works sometimes and not others?
if it works once it should install it mate np's
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
beany2009 said:
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
Click to expand...
Click to collapse
again thanks for your help
ok here goes red: PD 67100 ss-BC (4k)
SPL-4.6.2250.0(129193) mng
what you think?
i think my SPL was on that before so i dont know why u are having issues mate :/
maybe wait and see if a developer can read this and give us some info on why its not working for you :/
Thanx For The Help And the Tutorial It Was very Helpfull
Now my phone Is running dynamic 2.0
hey can u tell me what other custom roms are available that i can install on my phone and if there are any different methods of installing them
no problem mate glad it helped
erm the only other custom rom i have seen on mozart is deepdishing v7.0 you can find this in the development thread inside mozart topics
and for me mate im not sure and have not seen another way of installing another custom rom but im new to all this myself
anyway glad this helpped
regards
my computer wont pick up htc 7 mozart in bootloader
can anyone help me its doing my head in .
when you connect your phone to pc in bootloader its not showing as usb on the bottom of bootloader screen?
just serial?
just to confirm. this wont work on Asian handsets.
beany2009 said:
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
steve
Click to expand...
Click to collapse
Thx for the easy to follow guide.
It worked on a telstra brand mozart using windows 8.
Sent from my GT-N7105 using Tapatalk 2