Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
Related
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
tiagofa said:
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
Click to expand...
Click to collapse
if u are in Bootloader mode the one in three color mode.. U can downgrade surely with PDA viet temp.
In Boot loader mode just reconnect your device to pc through USB . and launch the PDA VIET program..
It should be work.
doesn´t work..
is there any connection with SD slot card doesn´t work ?.. ?? :S
help.. :S
u r using vista right?
u should do that with xp
be sure that with xp u can fix it 100%
no, i+m using xp.. still doens´t work..
i think my prophet dies :S
try flashing NVID wm5 when in bootloader. if you were successfull flash HardSPL and after that you original ROM!
First, disable any firewall
Put the prophet in bootloader (3-clored screen) by pushing CAM button and punching the reset hole at the bottom. When you realease the stylus, the colors should appear.
Then, before connecting your prophet to the PC, first DISable the "Allow USB connection" option in the connectionsettings box of ActiveSync.
After that connect the bootloadermoded Prophet to your PC, it conects as an ordinairy USB device. Then run the RUU of your choice.
probably the better idea is to send a snapshot of your display in fault mode.
do that with a camera. it could be useful to identify the state of your error.
i'm not skilled but here you can find a pool of powerfull developers.
jork
problem solve
problem.. usb port lol :S
Hi All,
Quick recap, I tried to install WM6 on a lower than 2.1 IPL/SPl so phone got stuck in boot screen, then i went to download an official WM5 rom from Tmobile, then I went into bootloader and successfully flash the official ROm. After flashing the official rom and multiple hard reset, phone is stuck on the bootscreen with the following info:
IPL 3.08
SPL 3.08.0000
GSM 02.69.21
OS 3.8.2.21
Am confused by the OS version isnt it meant to be 5.XXX because its a WM6.
Please.
Please anyone, I am pulling my hair out on this one...
Hello!
Try to use the following recovery method.
rmagyar said:
Hello!
Try to use the following recovery method.
Click to expand...
Click to collapse
Thanks for the reply I have downloaded the rescue kit and i have read the instruction, but the phone is not been connected in the bootloader mode even though i have the Xp usb driver connection. When I connect the usb cable after going into bootloader mode, the pc makes the usb connection sound but when when i run the Romupdate utility i get this error 260 connection error. What can I try again.
Thanks in advance.
I got this problem too.
I dont khnow wat to do, please help as.
rmagyar said:
Hello!
Try to use the following recovery method.
Click to expand...
Click to collapse
I have been able to successfully flash the phone again using the recovery kit but after flashing i took out the battery and powered up the phone, its still stuck at the boot screen with the same message.
IPL 3.08
SPL 3.08.0000
GSM 02.69.21
OS 3.8.2.21.
has it gone beyond the point of no return.?
Okay, am helpless here, Is anyone on here willing to fix this phone for me if I can post to them, and pay postage both ways?
did you find any solution?
Hallo!
I have exactly the same problem and I don't know what to do?
Do you guys have any news??
http://forum.xda-developers.com/showthread.php?t=406486&page=23
I need your help
My tytn is bricked
The Bootloader shows me HERM200 IPL-1.01 (White font, Red line)
HERM200 MFG SPL-1.01 (Yellow font) Redline)
I cant connect with my active sync anymore
The OS do not boot anymore
It shows my "no gsm"
It freezed by Windows Mobile Screen !
What can i do ?
Can anybody repair it ?
My english ist so bad, i come from Germany. SRY
I hope anybody can help me
Freeheld
press these buttons together: side ok button, power button and reset button,
then the HTC will go in USB mode and use some rom to flash it
thx for ur answer
when i try to flash it says me Error connecting
actice sync doesnt find my Tytn no conection
the tytn goes to the grey flash screen and interrupt it
can anybody tell my the right ROMs ?
i need a german roms and german radio rom
i have found my bricked Type
SPL HTC_BOOT Boot OS? No GSM? KITL
1.01MFG <=0107 No Yes ---
Diagnostic
bricked while flashing radio
Solution
Flash any type2 radio in NBF format, run RUU 2 times. If that doesn’t work, flash the radio using HERMflasher
i cant find "type2 radio roms in NBF format"
How i can see my HTC_BOOT ?
I crashed my tytn so hard
A new problem
Microsoft ActiveSync cannot recognize this device for one reason:
*The device was not connected properly.
.
.
.
And so one
How i can flash an new right ROM ?
You can flash from the SD-Card:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Here are the radio ROMs:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Thx but it doenst worked
i get an error
Loading...
than cant find file
but i renamed it write ???
how i can see that i have hardSPL
i dont beleave that i have it
and i cant install it because my activsync doenst work
If you're using XP - untick "Allow USB Connections" in activesync on pc. Put Hermes into bootloader and run the flash for Hard SPL V7. If this works then try an sd card flash for a different rom. No guarantees it will work but at this point, what have you got to loose?
Good Luck...
it doesnt work very well
i get an UPDATE ERROR
hmmmm
active sync is unticked (USB)
i have found a problem
i had flasched the bootloader 1.01MFG without SuperCID now i get Level= FF in mtty.exe, so i can flash back to 1.04 to install HARD SPL
How can i come back to 1.04 ?
help me please bro,, i want hacked my htc hd 2 and first i flash with hspl in this
and susscessed,,
and next my step is flashing stock room and i download in this
Code:
4shared.com/dir/22189940/b8552fa0/Shipped_Leo_ROMs.html
i download stock rom LEO 2.10 next my htc hd2 updating sudenly htc hd2 restart before finished update the screen after restart is triangle look like this pic
and i tried another stock rom but the screen like this
and im waiting but the loading never finished
this my tricolor
SPL 2.08 before i flash stock rom my spl 1.42
anything idea how to fix my htc hd2 problem ???
thanks for your help
The problem is with the spl. In order to flash roms that are not for your device you need hspl. Your spl is only 2.08.0000, you need to change this to 2.08.hspl.
ClydeB1 said:
The problem is with the spl. In order to flash roms that are not for your device you need hspl. Your spl is only 2.08.0000, you need to change this to 2.08.hspl.
Click to expand...
Click to collapse
you mean i must download this file bro ?
Code:
forum.xda-developers.com/attachment.php?attachmentid=297541&d=1269287146
how i can change 2.08 hspl where my htc hd 2 can't connect with activesync ??
thanks for ur help bro
****thefuckerz said:
you mean i must download this file bro ?
Code:
forum.xda-developers.com/attachment.php?attachmentid=297541&d=1269287146
how i can change 2.08 hspl where my htc hd 2 can't connect with activesync ??
thanks for ur help bro
Click to expand...
Click to collapse
No need for ActiveSync. Put phone in bootloader (tri-colour), connect to pc and when device shows usb in the bootm section of the screen run the hspl app again. Choose 2.08.hspl and all will be fine.
****thefuckerz said:
you mean i must download this file bro ?
Code:
forum.xda-developers.com/attachment.php?attachmentid=297541&d=1269287146
how i can change 2.08 hspl where my htc hd 2 can't connect with activesync ??
thanks for ur help bro
Click to expand...
Click to collapse
thats correct
you must go into bootloader mode, start the the tool and then u can install it(push and hold volume down+turn on the phone)
ClydeB1 said:
No need for ActiveSync. Put phone in bootloader (tri-colour), connect to pc and when device shows usb in the bootm section of the screen run the hspl app again. Choose 2.08.hspl and all will be fine.
Click to expand...
Click to collapse
ok i'll try bro thanks again for ur help...u have yahoo id bro?
****thefuckerz said:
ok i'll try bro thanks again for ur help...u have yahoo id bro?
Click to expand...
Click to collapse
Pleasure m8. No I don't. You can PM me though if you have more questions.
ClydeB1 said:
No need for ActiveSync. Put phone in bootloader (tri-colour), connect to pc and when device shows usb in the bootm section of the screen run the hspl app again. Choose 2.08.hspl and all will be fine.
Click to expand...
Click to collapse
Thanks bro,,sucessfuly
what should i do now to hacked my htc hd 2 bro ?
****thefuckerz said:
Thanks bro,,sucessfuly
what should i do now to hacked my htc hd 2 bro ?
Click to expand...
Click to collapse
Load spl 2.08.hspl by running the hspl2 tool. Once that is successful (check in bootloader again to see that it has successfully installed) then you can flash to the rom of your choice.
hi pls help
hi i have same problem i did everything but for me it didnt work why i saw it worked for that guy pls help
loonyozzy said:
hi i have same problem i did everything but for me it didnt work why i saw it worked for that guy pls help
Click to expand...
Click to collapse
Enter bootloader and supply all of the info you see there.
Actually you can't do much wrong. just connect the to your pc and then use the brilliant hspl2 to hack your spl on the phone, and then you can reflash the rom....
I have had same symptoms, tried everything... then....
Finally I have noticed that I can't flash through USB because on my micro-sd card I have placed LEOIMG.nbh which caused HSPL error 0028002
Before you flash remove micro-sd.
I hope my experience will help.
SAME problem no resolution
HI I have same problem Screen with exclamation mark then boot screen with gour colours showing this
HX-BC
SPL-1.42.0000 XE.
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So I've tried to install HSPL 1.42 With no card inside but during installation i get.
Download http://forum.xda-developers.com/attachment.php?attachmentid=297541&d=1269287146
1. Remove micro SD card.
2. Reboot phone while holding volume down.
3. Connect to the PC via USB.
4. Run HSPL2_RUN.exe and follow the steps on your screen
Same problem
Hi, I have also this problem. I tried to install the stock rom but during it an error occured and it stopped before finished. Then there is the triangle and "software update failed". My spl says that I have the version 3. and something and also when I try to run the hspl.exe an error occurs that says that a file RAPi.dll cannot be found and then it waits for usb connection and finaly an error occurs "cannot connect".
Please could someone help me ? WHat am I doing wrong ? Or what should I do ?
thanks