for those who cant get pass the "Hard-Soft SPL - created by sp3dev",
1- You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone.
2- Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3- Download http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar and upgrade your phone using the Flasher included in the file you downloaded in step 2.
I did mine, and now I have wm6.1 installed in my phone. and I loved it.
Thank you all for your input
charlietruong said:
for those who cant get pass the "Hard-Soft SPL - created by sp3dev",
1- You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone.
2- Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3- Download http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar and upgrade your phone using the Flasher included in the file you downloaded in step 2.
I did mine, and now I have wm6.1 installed in my phone. and I loved it.
Thank you all for your input
Click to expand...
Click to collapse
how the software unlock?
Copy all 3 files you downloaded in step #1 to your Oxygen. Then execute all 3 files in numerical order.
Good luck!
charlietruong said:
Copy all 3 files you downloaded in step #1 to your Oxygen. Then execute all 3 files in numerical order.
Good luck!
Click to expand...
Click to collapse
sotty after the white screen when i connect my smartphone to my pc nothing happens and activesync says no connection
it's ok. when you see the white screen and after you plug it in the computer, wait about 10 seconds then start upgrading.
charlietruong said:
it's ok. when you see the white screen and after you plug it in the computer, wait about 10 seconds then start upgrading.
Click to expand...
Click to collapse
oh yes I am successful
colataroc said:
oh yes I am successful
Click to expand...
Click to collapse
Hi,
would you please show me how you did it. My phone can only go in bootloader mode, like yours was. Please help. Thanks
traiviet said:
Hi,
would you please show me how you did it. My phone can only go in bootloader mode, like yours was. Please help. Thanks
Click to expand...
Click to collapse
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
colataroc said:
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
Click to expand...
Click to collapse
Thank you, but I can only get to the bootloader mode. I can't get pass the Windows Mobile screen.
traiviet said:
Thank you, but I can only get to the bootloader mode. I can't get pass the Windows Mobile screen.
Click to expand...
Click to collapse
oh i'm sotty but for this i don't know. i think you have already read this : http://forum.xda-developers.com/showthread.php?p=2186022
To fix your phone if its in the bootloader download this rom:
http://www.leaf.co.za/downloads/ROMS/Oxygen/Oxygen%20-%20P%20N%2099HCD064%20-%2024%20January%202007.exe
And flash it to your phone. It will then boot up in WM5.
This ROM has English and Russian.
Mavix_2008 said:
To fix your phone if its in the bootloader download this rom:
http://www.leaf.co.za/downloads/ROMS/Oxygen/Oxygen%20-%20P%20N%2099HCD064%20-%2024%20January%202007.exe
And flash it to your phone. It will then boot up in WM5.
This ROM has English and Russian.
Click to expand...
Click to collapse
thank you. i will try now. you'd be my life saver if it works. I'll let you know as soon as i try to reflash my phone.
hi Mavix_2008
i tried flashing this rom but it didnt work. it just reset at 4% and says Invalid vender ID. I dont know whats wrong with my phone.
Thx for all, i success =)=)=)
SIM unlock
I tried you procedure but I was blocked by an error message saying "no application associated to spl".
I could not launch spl.lnk
Could some one help me to resolve this.
Thanks
Anzad
SIM unlock
colataroc said:
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
Click to expand...
Click to collapse
Hello,
I Tried your procedure in order to update my WM and then unlock my mobile but I was blocked by an error message saying "No application associated de spl". I could not run spl.lnk
Could you help me please
Thanks
Anzad
Hi,
I installed the HTC.Device.Software.Unlock.
I copied the 3 files spl.nb, spl.lnk and jumpspl.exe...I hold the camera button at the spl.lnk...I wait...1 minute...2minutes...but nothing happens.
I just have to hold the camera button or I have to open the spl.lnk too?
Could you please help me?
Thank you
Hi,
I'm interested for this ROM
But is it in French too?
Thanks for respons
Bye
A debutant...
Great succes!!
colataroc said:
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
Click to expand...
Click to collapse
Thanks a lot for the great explanation! My first time on this forum, my first steps in modding my phone, instant succes!
Greets from a newb...
klaasroelofs said:
Thanks a lot for the great explanation! My first time on this forum, my first steps in modding my phone, instant succes!
Greets from a newb...
Click to expand...
Click to collapse
Do you have manualy lauched the spl.lnk or when you hold the camera button it launch automatically?
Related
I have a T-Mobile MDA Vario II and it just seems that flashing is impossible. I am pulling my hair out!
I have searched the forum and cannot see anyone else having had the same problem
I have tried to flash WM6, as provided by T-Mobile and also I have tried to flash Hard-SPL, but get the same problems with both.
First of all, if I try to flash by flashing from the PC, via ActiveSync, it all seems to be fine until it comes to that actual flashing itself. As soon as the flashing process begins, the phone goes to the bootloader and disconnects from ActiveSync, producing an error message in the program on the PC.
I have tried doing it directly on the phone, as described in post 1160 of the Hard-SPL, Or How to Not Brick Your PDA Ever Again And Fix Bad Blocks! thread, but when I reach step 7, where it should go from the tri-color screen to another screen, asking you to press the power button to start, it doesn't happen! The tri-color screen appears, followed, for less than a second, by a screen which says "Loading..." and then it just goes back to the bootloader screen, where it stays until I do a reset.
Anyone got any ideas at all?
CID Unlock the device then try to flash it, make sure battery is fully charged too. Have you tried entering bootloader manually then trying to flash the tmobile rom?
It won't even let me do that!
I have just tried to do this, using pof's free HTC Hermes SIM & CID Unlocker but even that won't work.
Pof's zip file contains 3 methods of doing this. I'll list all 3, with a description of where it goes wrong each time. Perhaps that will make the problem clearer
Easy auto-install Instructions:
-------------------------------
1. Unzip unlocker and run AUTO_Unlock_v3a.bat
2. Follow directions on screen
The .bat file starts a program on the PC. It goes OK, until it sends the phone to the boot loader screen. ActiveSync immediately disconnects and an error message comes up on the PC...
ERROR [260]: CONNECTION
The Update Utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone
Check the following:
1. The PDA Phone is connected to the USB cradle/cable
The USB cradle/cable is connected to the PC
Click 'Exit' to quit
manual instructions:
---------------------------------------------------------------------
1. Transfer SSPL/SSPL-HERM.exe to your phone and run it
2. Tri color screen will appear
3. Disable activesync (file -> connection settings -> uncheck "allow USB connections")
4. Connect your phone to your computer using the USB lead.
As long as the Tri-color screen is showing, the PC does not recognise the PDA Phone as being connected, even if the USB is connected
5. run RUU/RUU_HERM_Unlock_v3a.exe
6. follow the flashing process (Check the "I understand..." and "I completed..." boxes and update!)
Rather unsurprisingly, the same error as above appears
7. Allow your phone to reboot.
8. Transfer HERM_Unlock_v3.exe program to your phone and run it
9. Click the Unlock Button, select unlock option. Select if you want SIM/CID unlock.
10. Click "Unlock!" and wait until process finishes.
11. When done, turn off your phone for 10 seconds and reboot after that.
I actually still went through steps 7 to 11 and it all seemed to work, but although it said the PDA Phone was now SuperCID, it wasn't
update using the SD-Card Method:
-------------------------------------------------------------------------------------
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe This file doesn't exist in the zip file
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button. Nothing to confirm. The phone simply goes straight to the Tri-color screen and stays there until you do a soft reset
Again, I don't know how much help it is, but if I go to the boot loader screen, via the power, OK and soft resent buttons, I see the following information...
HERM300
IPL-1.01
HERM300
SPL-1.04
If I run the SSPL-HERM program on the phone, it takes me to the boot loader screen, but with the following info...
HERM300
HERM-SSPL by des
HERM300
SPL-1.09.ds
Any ideas?
Go to bootloader and tell us what your SPL is... If its 2.10 olipro then you have Hard SPL installed. This process is VERY quick so it may have worked and you just didn't notice the change.
As for using the PC & Activesync, if you have Hard SPl, use the sd card method to load new OS's onto your Phone instead as its safer and easier (same as how you loaded Hard SPL except you don't need to run the SSPL program from your device, just put file on card, rename and reset to bootloader.
Cheers...
That info is in the prevoius post. Before you worry that you are going mad, I edited the message to add that info, so I guess you probably asked, before that info was there
Hi,
Customer Bring Me Bricked Gene(Dead Condition)
Its Only Go To Boot Loader Mode and also detactable
(USB Icon Show When Enter Cable)
Here is the Details.
ONBL 1.07.0000
SPL 1.10.Olip
Serial Number Start with 8XX
When I Would Like To Update Rom With Rom Update Utiliy This Error Appear.
p3400 error 300 invalid update tool
How To Solve This Problem ?
Is My Genie is Old?
Rgds
Bluffmaster
bluffmaster said:
Hi,
Customer Bring Me Bricked Gene(Dead Condition)
Its Only Go To Boot Loader Mode and also detactable
(USB Icon Show When Enter Cable)
Here is the Details.
ONBL 1.07.0000
SPL 1.10.Olip
Serial Number Start with 8XX
When I Would Like To Update Rom With Rom Update Utiliy This Error Appear.
p3400 error 300 invalid update tool
How To Solve This Problem ?
Is My Genie is Old?
Rgds
Bluffmaster
Click to expand...
Click to collapse
Go through the Rom upgrading guide.Read thoroughly and follow every step carefully.there is a difference between Old Gene and New Gene.You will learn as you follow the guide as to which one is yours.Also to avoid invalid update tool errors,make sure your device is properly synced to yur computer.In your cas as the device is fully dead.Perform a Hard Reset.Even if that doesnt work,you have to use JTAG method to get back your Gene.
So follow the Guide and you'll do good.Revert back when your problem is solved.And do not Create New Threads unnecessarily.Post your doubts in the respective threads.
karan999 said:
Go through the Rom upgrading guide.Read thoroughly and follow every step carefully.there is a difference between Old Gene and New Gene.You will learn as you follow the guide as to which one is yours.Also to avoid invalid update tool errors,make sure your device is properly synced to yur computer.In your cas as the device is fully dead.Perform a Hard Reset.Even if that doesnt work,you have to use JTAG method to get back your Gene.
So follow the Guide and you'll do good.Revert back when your problem is solved.And do not Create New Threads unnecessarily.Post your doubts in the respective threads.
Click to expand...
Click to collapse
Hi
I follow the guide and Upgrade my SPL Olipro to Orefkov's.
PHP:
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 5 of Guide is Goes Well....
But Guide Show in Step 6 phone boot Once
PHP:
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
But Mine is Still Dead When i Press Power Button only redlight blink.
also it can go to bootloader when i press power + camera key.
i have sucessfully update my rom but now phone still dead
rgds
bluffmaster
bluffmaster said:
Hi
I follow the guide and Upgrade my SPL Olipro to Orefkov's.
PHP:
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 5 of Guide is Goes Well....
But Guide Show in Step 6 phone boot Once
PHP:
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
But Mine is Still Dead When i Press Power Button only redlight blink.
also it can go to bootloader when i press power + camera key.
i have sucessfully update my rom but now phone still dead
rgds
bluffmaster
Click to expand...
Click to collapse
Hi Friend i have the same problem
I successfully go to the (3. Connect the USB cable. The text USB will appear on the bottom of the screen.) after that when touch the usb text on my mobile it not responding & the Mtty1_42.exe programe the window will open but i cannot write any thing. please help me .
Make sure that you have removed SIM card and Storage card and try to connect it again.Then run mtty1_42.exe and select USB in the port then press OK.Hope this will help you.
mr.harsh said:
Make sure that you have removed SIM card and Storage card and try to connect it again.Then run mtty1_42.exe and select USB in the port then press OK.Hope this will help you.
Click to expand...
Click to collapse
I already remove my sim & storage card but now i can not switch on my phone / When i Press Power Button only redlight blink. also it can go to bootloader when i press power + camera key.
gcpganesh said:
Hi Friend i have the same problem
I successfully go to the (3. Connect the USB cable. The text USB will appear on the bottom of the screen.) after that when touch the usb text on my mobile it not responding & the Mtty1_42.exe programe the window will open but i cannot write any thing. please help me .
Click to expand...
Click to collapse
good morming
On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
it don´t apear any window after run mttyy1_42. Open a program bu i don´t see any button USB!!!
Cam you help me??
Thanks
HLCMAD said:
good morming
On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
it don´t apear any window after run mttyy1_42. Open a program bu i don´t see any button USB!!!
Cam you help me??
Thanks
Click to expand...
Click to collapse
Thank u friend
when i chose USB button of mobile it is not responding & I can not write any thing in mttyy1_42 programe.
to be able to do the command in the MTTY programe, for the first you should disable activesync -> connection settings -> uncheck "allow USB connections"
Hakim Rahman said:
to be able to do the command in the MTTY programe, for the first you should disable activesync -> connection settings -> uncheck "allow USB connections"
Click to expand...
Click to collapse
Thank you friend i already done it, when conect the phone to computer through USB ,In a corner position of the phone USB is written, but when i open the MTTY program it open & shows the Port option to chose , but it is not showing the USB option in that option.
gcpganesh said:
Thank you friend i already done it, when conect the phone to computer through USB ,In a corner position of the phone USB is written, but when i open the MTTY program it open & shows the Port option to chose , but it is not showing the USB option in that option.
Click to expand...
Click to collapse
If it does not exist, You can add it by typing USB on port column option
Hakim Rahman said:
If it does not exist, You can add it by typing USB on port column option
Click to expand...
Click to collapse
Thank U,
I add it but i got this " \\.\WCEUSBSH001 port can not open" Error Message.
(If Any thing i have to do after connecting USB Cable to phone to PC)
gcpganesh said:
Thank U,
I add it but i got this " \\.\WCEUSBSH001 port can not open" Error Message.
(If Any thing i have to do after connecting USB Cable to phone to PC)
Click to expand...
Click to collapse
You've kill processes wcescomm.exe on Task Manager ??
Hakim Rahman said:
You've kill processes wcescomm.exe on Task Manager ??
Click to expand...
Click to collapse
Thank u Friend
Now how can i update 6 professional to 6.5
gcpganesh said:
Thank u Friend
Now how can i update 6 professional to 6.5
Click to expand...
Click to collapse
for upgrade to WM 6.5, you can follow existing Guide by krazy_about_technology at http://forum.xda-developers.com/showthread.php?t=472169
This guide is similar as for Android HTC's
0. You must have RUU executable file such as
RUU_Omega_HTC_Europe_1.07.401.01_Radio_16.23.02.09_2_16.24.00.23U_Signed_OMEGA_RELEASE.exe
Click to expand...
Click to collapse
and .nbd file like
IMG_Omega_HTC_Europe_1.09.401.02_Radio_16.23.02.09_2_16.24.00.23U_Signed_OMEGA_RELEASE.nbh
Click to expand...
Click to collapse
1. Download Microsoft's Process Monitor and extract somewhere
2. Start Process Monitor and setup filers as follow:
3. Run RUU and see where the file it's extracted, in most cases it is SystemDriveLetter:\Users\YourUser\appdata\Local\Temp and the directory starts with the pf...
4. Browse to folder where you will find following files:
EnterBootloader.exe
ErrorBattery.fig
ErrorUSB.fig
rapitool.exe
README.doc
ROMUpdateUtility.cfg
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
RUU_signed.nbh
Click to expand...
Click to collapse
5. Copy the contect to other location for further usage
6. Replace RUU_signed.nbh with .nbh you have insted (don't forget to rename it to RUU_signed.nbh)
And thats all - installer does not see the phone!
Entering the bootloader displays a b&w phone connected to a pc - pc recognizes its as Omega and thats all... - any ideas?
I got a bit further. You have to power the phone on whilst holding down the Volume Up and Down button/s at the same time.
This takes you to a screen where you can Factory Reset etc. The PC will pick the phone up using the USB cable and you can follow your instructions above.
However, when I tried I get: ERROR [244] : INVALID MODEL ID
I have a Orange UK branded phone, I have followed your instructions above. I will look for another RUU to test.
jclubb said:
I got a bit further. You have to power the phone on whilst holding down the Volume Up and Down button/s at the same time.
This takes you to a screen where you can Factory Reset etc. The PC will pick the phone up using the USB cable and you can follow your instructions above.
However, when I tried I get: ERROR [244] : INVALID MODEL ID
I have a Orange UK branded phone, I have followed your instructions above. I will look for another RUU to test.
Click to expand...
Click to collapse
Will try that with my unbranded phone this afternoon and will leave some feedback as well
Hello guys!
Let me tell you a story...
I bought an Lumia 710 a few days ago and now I want do debrand it and update it to Windows Phone 7.8. I've followed every single tutorial I could find on the internet, starting from debranding to unlocking bootloader and jailbreaking it. Didn't tried everyone in fear of messing the phone up.
I ended up on Nokia Care Suite with a few firmware files and a very huge desire to update my phone. The matter is that, as soon as I connect my phone to start the flashing process on NCS, it reboots (the phone), vibrates and keeps on this semi-power off state. I know that this was supposed to happen, but now NCS doesn't recognise my phone in *any* way. I can reboot the phone holding vol+, reboot holding nothing, start all over again... Just nothing.
All I want is to debrand my phone to a Nokia firmware (not a TIM one, I really hate those custom boot and apps) and update it to WP7.8, but I also want to work with Zune (sync and updates). Can someone PLEASE help me?
One more thing: when I was reading about all these stuff, I came up with the unlocking bootloader process. It said that I needed to have the Qualcomm boot loader, so I tried to identify it (holding vol+ and plugging USB) and it appeared on my device manager something like Qualcomm MSM blah blah blah. This means that my phone is with Qualcomm bootloaders, right?
Thanks in advance!
If device manager says you have a Qualcomm bootloader you are 90% of the way there
All you need to do now is download this downloader.exe
http://forum.xda-developers.com/showthread.php?t=1665821
Download NaviFirm Plus from here
http://www.symbian-toys.com/navifirm.aspx
In Navifirm Plus, navigate to here
http://localhostr.com/files/jXWZZOI/Capture.PNG
And hit the download button
When it is downloaded, goto the download location and copy this file to the desktop or a folder
http://localhostr.com/files/eT3POA2/Capture.PNG
Use 7zip to extract that file and you should have 'boot.img' file
Rename that to stock.nb (You'll need to enable file extensions to be shown so you can see the .img and .nb extensions - do that from folders view menu)
Now extract that downloader.exe you got from the first link I posted and copy stock.nb into the same folder
You should have downloader.exe and stock.nb in that folder
Ok, now unplug your phone from the PC
Power off the phone
Hold Volume+ button in and plug in the phone to USB > PC
When you feel the short vibrate, release the Volume+ button
IF THE PC ASKS TO FORMAT THE PHONE, PRESS CANCEL, DO NOT FORMAT OR YOUR PHONE IS DEAD
Wait for the driver to install (If it has not already)
Run downloader.exe as Admin
Press the button on the downloader.exe to start flashing the phone
Wait for it to complete then remove the phone battery for 10 seconds, and then put it back in and reboot into 7.8
Done
If you can't stop the phone rebooting after plugging in the USB cable, try it without the battery in
If you don't have the qualcomm bootloader, use this NSS to flash the bootloader then repeat the above
http://forum.xda-developers.com/showthread.php?t=1620629
Good luck
THANK YOU! Updated to Windows Phone 7.8 with this method
I don't want to sound inconvenient, but how do I jailbreak/root it now? This is the last thing that is missing
Thanks a LOT!
Renan Lazarotto said:
THANK YOU! Updated to Windows Phone 7.8 with this method
I don't want to sound inconvenient, but how do I jailbreak/root it now? This is the last thing that is missing
Thanks a LOT!
Click to expand...
Click to collapse
No problem
You can't actually jailbreak stock ROMs yet (Sucks I know), you have to flash an already unlocked ROM from one of the devs here
Same method as above, only swap the stock ROM for the custom one
(What I missed from above, and thankfully you were clever enough to know not to do it, is when the PC asks to format the phone, ALWAYS press CANCEL, DO NOT FORMAT or you kill the phone dead !)
*Detection* said:
No problem
You can't actually jailbreak stock ROMs yet (Sucks I know), you have to flash an already unlocked ROM from one of the devs here
Same method as above, only swap the stock ROM for the custom one
(What I missed from above, and thankfully you were clever enough to know not to do it, is when the PC asks to format the phone, ALWAYS press CANCEL, DO NOT FORMAT or you kill the phone dead !)
Click to expand...
Click to collapse
And how can I modify an stock-rom to add these features? I was searching for it a few time ago, I've played with the OS Builder but I was a bit nervous on doing something wrong. I've also searched for some tutorials but haven't found anything yet. Can you point me where I should start?
Thanks!
Renan Lazarotto said:
And how can I modify an stock-rom to add these features? I was searching for it a few time ago, I've played with the OS Builder but I was a bit nervous on doing something wrong. I've also searched for some tutorials but haven't found anything yet. Can you point me where I should start?
Thanks!
Click to expand...
Click to collapse
I'd ask one of the devs here, I haven't tried to customise a ROM yet
Just reply to one of the 710 custom ROM threads or PM the dev
first, i would recommend you doing some reading: wp7 chef central
lordmaxey said:
first, i would recommend you doing some reading: wp7 chef central
Click to expand...
Click to collapse
Renan Lazarotto said:
I was searching for it a few time ago, I've played with the OS Builder but I was a bit nervous on doing something wrong. I've also searched for some tutorials but haven't found anything yet.
Click to expand...
Click to collapse
Already searched, nothing very well detailed...
@ detection
*Detection* said:
If device manager says you have a Qualcomm bootloader you are 90% of the way there
All you need to do now is download this downloader.exe
http://forum.xda-developers.com/showthread.php?t=1665821
Download NaviFirm Plus from here
http://www.symbian-toys.com/navifirm.aspx
In Navifirm Plus, navigate to here
http://localhostr.com/files/jXWZZOI/Capture.PNG
And hit the download button
When it is downloaded, goto the download location and copy this file to the desktop or a folder
http://localhostr.com/files/eT3POA2/Capture.PNG
Use 7zip to extract that file and you should have 'boot.img' file
Rename that to stock.nb (You'll need to enable file extensions to be shown so you can see the .img and .nb extensions - do that from folders view menu)
Now extract that downloader.exe you got from the first link I posted and copy stock.nb into the same folder
You should have downloader.exe and stock.nb in that folder
Ok, now unplug your phone from the PC
Power off the phone
Hold Volume+ button in and plug in the phone to USB > PC
When you feel the short vibrate, release the Volume+ button
IF THE PC ASKS TO FORMAT THE PHONE, PRESS CANCEL, DO NOT FORMAT OR YOUR PHONE IS DEAD
Wait for the driver to install (If it has not already)
Run downloader.exe as Admin
Press the button on the downloader.exe to start flashing the phone
Wait for it to complete then remove the phone battery for 10 seconds, and then put it back in and reboot into 7.8
Done
If you can't stop the phone rebooting after plugging in the USB cable, try it without the battery in
If you don't have the qualcomm bootloader, use this NSS to flash the bootloader then repeat the above
http://forum.xda-developers.com/showthread.php?t=1620629
Good luck
Click to expand...
Click to collapse
What if device manager also dont see the lumia 710.
Like my problem here.
What can i do now?
Bump.
ive click n formated the phone now its not booting up plz help:crying:
Thanks for this wonderful tutorial
Used it to reboot my dead lumia 710
wondering why his post in 2016? Bored and jobless
*Detection* said:
If device manager says you have a Qualcomm bootloader you are 90% of the way there
All you need to do now is download this downloader.exe
http://forum.xda-developers.com/showthread.php?t=1665821
Download NaviFirm Plus from here
http://www.symbian-toys.com/navifirm.aspx
In Navifirm Plus, navigate to here
http://localhostr.com/files/jXWZZOI/Capture.PNG
And hit the download button
When it is downloaded, goto the download location and copy this file to the desktop or a folder
http://localhostr.com/files/eT3POA2/Capture.PNG
Use 7zip to extract that file and you should have 'boot.img' file
Rename that to stock.nb (You'll need to enable file extensions to be shown so you can see the .img and .nb extensions - do that from folders view menu)
Now extract that downloader.exe you got from the first link I posted and copy stock.nb into the same folder
You should have downloader.exe and stock.nb in that folder
Ok, now unplug your phone from the PC
Power off the phone
Hold Volume+ button in and plug in the phone to USB > PC
When you feel the short vibrate, release the Volume+ button
IF THE PC ASKS TO FORMAT THE PHONE, PRESS CANCEL, DO NOT FORMAT OR YOUR PHONE IS DEAD
Wait for the driver to install (If it has not already)
Run downloader.exe as Admin
Press the button on the downloader.exe to start flashing the phone
Wait for it to complete then remove the phone battery for 10 seconds, and then put it back in and reboot into 7.8
Done
If you can't stop the phone rebooting after plugging in the USB cable, try it without the battery in
If you don't have the qualcomm bootloader, use this NSS to flash the bootloader then repeat the above
http://forum.xda-developers.com/showthread.php?t=1620629
Good luck
Click to expand...
Click to collapse
i successfully downgraded my F320s after i took kitkat ota here is how i did it.i used steps from this thread, http://forum.xda-developers.com/showthread.php?t=2636869 which as follows
[EDIT]: Cleaned the guide up a bit
Install
1. Install the LG drivers downloaded above.
2. Install LGFlashTools v1.5 (but don't run it)
3. Extract the DLL and the TOT files from above and put them in a nice tidy directory
.TOT https://drive.google.com/file/d/0B1kmABKJi1C6TUFaTUJldWxLN3M/edit?usp=sharing
.dll https://drive.google.com/file/d/0B1kmABKJi1C6Z1ZFbnpLYXJ0NmM/edit?usp=sharing
Flash tool https://drive.google.com/file/d/0B1kmABKJi1C6bEpMbHdIVG9XUlk/edit?usp=sharing
Drivers initialization
1. Put the phone into download mode. (Turn off device, keep pressing volume up while plugging in the micro usb cable.
2. Let the phone initialize and install the drivers. Once done, in Device manager, you should see the LG phone listed under COM ports (something along these lines).
3. Find that LG entry in Device Manager, click on Properties, Advanced and then change the COM port to COM41 and close/save.
4. Unplug your phone! Important step.
LGFlashTools
To get this tool to work, you'll need to do a few tricks.
1. Set the computer's date to some time in July 2012 or before.
2. Disconnect the internet
3. Find a serial number or register key for LG flash tool 1.5 (search the web)
4. Execute the LGFlashTools. It should ask you for a key, put it in. Now you should see a dialog where you can load the DLL file and the TOT files that you extracted earlier. Put them both in here. Click ok
Flashing
5. There is a yellow arrow on the top left. Click on it to initialize the process. Once done, it should say "ready/finished" or whatever.
6. Put the phone in download mode again, and plug it into the USB port. LG FLash Tools should start flashing it automatically. When it's done, it'll automatically reboot into your stock Shipped rom and all of your data and internal sdcard files are gone.
i will be uploading the tot file for f320s on my google drive for anyone who needs it, the rest you should be able to get easily on your own.
a big thank you to Seven Winds for the post and everyone who helped. ( please pm me so i can add your name to the Thanks list.)