Anyone know if there is a manual on how to install a new full housing for the hd? http://cgi.ebay.com/ws/eBayISAPI.dl...rms=algo=SI&its=I&itu=UCI&otn=15&po=LVI&ps=54
you can find in mikechannel.com
it doesnt tell you how to remove the display and install the digitizer.
Related
Hello
Where I can buy LCD display for Acer Liquid s100?
Thanks.
You can get one on ebay. Although i don't know how to get the damn thing open. Have you been able to remove your LCD ? so that you can replace it ? could you tell me how if you did. thanks.
Hi there,
Even I got my Liquid lcd broken,too.Anyone can help changing it with tutorial.Thanks in advance.
Try keepintouch web site. Just do a search for item# 771 It should bring "LCD Screen Display Ecran Panel For Acer Liquid A1 S100 Original New TFT"
As for disassembling your Acer Liquid E it is much harder than some other cell phones. Here is a guide attached that might somewhat help you with your task. I found it on Android Forums web site.
Acer A1 S100 Service Manual - Disassemble Procedure
Acer A1 S100 Service Manual [PDF] - Disassemble Procedure
I searched the web for days looking for a tut or a service manual and finally found the full service manual with the complete disassemble procedure - including pics.
www[dot]box[dot]net/shared/rylqej72jp
or
www[dot]box[dot]net/shared/r33btt9iju
or
h**p://rapidshare.com/files/445403533/ACER_A1_S100_User___Service_Guide.rar
or
h**p://hotfile.com/dl/100749010/c85027a/ACER.A1.S100.User.Plus.Service.Guide.rar.html
I tore mine down without this manual, wasn't too difficult but proceed very slowly because the double sided adhesives they use stick quite well and it's easy to damage the FPC flex cables if you're not careful, especially at the bottom of the phone below PCB. Make sure you have the correct tools for prying (plastic or Mylar).
Hope this helps...
You can find new lcd screens for liquid from Ebay.
is anybody here who has successfully separated the display and touchunit from ther frontcover of its x10`?
my cover is broken and i would like to buy a new cover set without a new screen.
i´d like to keep it. ppl told me that the screen is glues so maybe somebody knows how get it removed without any damage
cheers
First watch this: http://www.youtube.com/watch?v=ypmgeoaDURQ
Then: http://www.youtube.com/watch?v=jhUa7R2KOTc
probably easier to just fit the new screen
Anyone tried changing the housing before and could recommend a video guide? thanks, I am still using my current digitizer and lcd screen by the way. just wanna change the cover color of my s3. Thanks
I have a problem with the cracked screen of my Xperia Active (st17i). Since the repairing cost the service centre will be more than half the price of a new phone, I’ll most probably need to order it and replace it myself.
I haven’t done this before so I’ll need all the advice you can give me both on the hardware and the software part. If anyone have done it before or knows how to do it all tips are welcome.
On the hardware part:
In ebay I found replacement modules including both the screen and the digitizer, BUT not the metal frame to which they are attached. For reference you can see the attached photos. My question here is:
HOW or CAN I disassemble the LCD and the digitizer from the metal frame of the phone at home? They seem to be glued firmly to each other.
On the software part:
I understand that changing the hardware is only part of the problem. If I’m not mistaken after that I’ll have to flash the firmware and calibrate the new screen. The guy from the service centre explained that if I do not find the correct version to flash with the damage may be even worse.
So my questions here are two:
1) Can anyone point which is the correct version to flash (and instructions)?
2) How or Can I calibrate the screen?
.
Read this post
donZe said:
I have a problem with the cracked screen of my Xperia Active (st17i). Since the repairing cost the service centre will be more than half the price of a new phone, I’ll most probably need to order it and replace it myself.
I haven’t done this before so I’ll need all the advice you can give me both on the hardware and the software part. If anyone have done it before or knows how to do it all tips are welcome.
On the hardware part:
In ebay I found replacement modules including both the screen and the digitizer, BUT not the metal frame to which they are attached. For reference you can see the attached photos. My question here is:
HOW or CAN I disassemble the LCD and the digitizer from the metal frame of the phone at home? They seem to be glued firmly to each other.
On the software part:
I understand that changing the hardware is only part of the problem. If I’m not mistaken after that I’ll have to flash the firmware and calibrate the new screen. The guy from the service centre explained that if I do not find the correct version to flash with the damage may be even worse.
So my questions here are two:
1) Can anyone point which is the correct version to flash (and instructions)?
2) How or Can I calibrate the screen?
.
Click to expand...
Click to collapse
This has been done with other devices but this may work for yours too.
Read this:
http://forum.xda-developers.com/showthread.php?t=2104484
Hit thanks if I helped you in any way.
Thanks for the link. I was looking at this topic before, but I am not sure whether it is about solving software-related touch-screen problems and if it is applicable in my case (screen replacement).
Does anyone know whether is it really necessary to flash the phone at all?
I also found an article online on screen calibration for xperia active and xperia mini. Here is the link.
It says there I should install ETS software with SETool. I have no idea what this is or how to do that. Can anyone help?
hi,
so i have 2 galaxy s3 i9300 both network unlocked one in red and one in white
the wife has dropped both, the red is put away for now, i managed to remove the lens from the white one, but wer the bang happend the volume up doesnt work and neither does the camera, i get sum exetion error, the chrome is rather tatty too, i puit a temp lens on for time being, and yep she dropped and broke that too,
I have a new lens here with the adhesive , the top and bottom kind, touch works fine
im trying to find a guide on how to swap the complete innards from the white housing to a new midframe if i buy one, but cant seem to find the actul working lcd removal, only the logic board and cameras
and the new lcd and screen complete are rather expensive at the moment my plan is this.
and i guess il need to order new camera.
buy new housing something like this
http://www.ebay.co.uk/itm/FRONT-REP...e_Replacement_Parts_Tools&hash=item2577355c8d
ande then remove the lcd and logic board form the white one i have now and put it in this and attach the new lens,,
is this atricky job, i was told removing the lens was, took me a hr but i did it with no damage,
help would be great! just sum advice or point me in right direction for a actual lcd removal and refitting giude, but not the complete unit as i have a lens already ,
thanx